This adds support for IRQ handling in the RC5T619 which is required
for properly implementing subdevices like RTC.
For now only definitions for the variant RC5T619 are included.
Signed-off-by: Andreas Kemnade <[email protected]>
---
Changes in v5:
rn5t618_irq_init static
Changes in v4:
merge rn5t618-irq.c into rn5t618.c
use macros for IRQ table
Changes in v3:
alignment cleanup
Changes in v2:
- no dead code, did some more testing and thinking for that
- remove extra empty lines
drivers/mfd/Kconfig | 1 +
drivers/mfd/rn5t618.c | 88 +++++++++++++++++++++++++++++++++++++
include/linux/mfd/rn5t618.h | 15 +++++++
3 files changed, 104 insertions(+)
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 2b203290e7b9..a7067888a41e 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1058,6 +1058,7 @@ config MFD_RN5T618
depends on OF
select MFD_CORE
select REGMAP_I2C
+ select REGMAP_IRQ
help
Say yes here to add support for the Ricoh RN5T567,
RN5T618, RC5T619 PMIC.
diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c
index ead2e79036a9..849a33d64860 100644
--- a/drivers/mfd/rn5t618.c
+++ b/drivers/mfd/rn5t618.c
@@ -8,6 +8,8 @@
#include <linux/delay.h>
#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
#include <linux/mfd/core.h>
#include <linux/mfd/rn5t618.h>
#include <linux/module.h>
@@ -46,9 +48,63 @@ static const struct regmap_config rn5t618_regmap_config = {
.cache_type = REGCACHE_RBTREE,
};
+static const struct regmap_irq rc5t619_irqs[] = {
+ REGMAP_IRQ_REG(RN5T618_IRQ_SYS, 0, BIT(0)),
+ REGMAP_IRQ_REG(RN5T618_IRQ_DCDC, 0, BIT(1)),
+ REGMAP_IRQ_REG(RN5T618_IRQ_RTC, 0, BIT(2)),
+ REGMAP_IRQ_REG(RN5T618_IRQ_ADC, 0, BIT(3)),
+ REGMAP_IRQ_REG(RN5T618_IRQ_GPIO, 0, BIT(4)),
+ REGMAP_IRQ_REG(RN5T618_IRQ_CHG, 0, BIT(6)),
+};
+
+static const struct regmap_irq_chip rc5t619_irq_chip = {
+ .name = "rc5t619",
+ .irqs = rc5t619_irqs,
+ .num_irqs = ARRAY_SIZE(rc5t619_irqs),
+ .num_regs = 1,
+ .status_base = RN5T618_INTMON,
+ .mask_base = RN5T618_INTEN,
+ .mask_invert = true,
+};
+
static struct rn5t618 *rn5t618_pm_power_off;
static struct notifier_block rn5t618_restart_handler;
+static int rn5t618_irq_init(struct rn5t618 *rn5t618)
+{
+ const struct regmap_irq_chip *irq_chip;
+ int ret;
+
+ if (!rn5t618->irq)
+ return 0;
+
+ switch (rn5t618->variant) {
+ case RC5T619:
+ irq_chip = &rc5t619_irq_chip;
+ break;
+ default:
+ irq_chip = NULL;
+ break;
+ }
+
+ if (!irq_chip) {
+ dev_err(rn5t618->dev, "Currently no IRQ support for variant %d\n",
+ (int)rn5t618->variant);
+ return -ENOENT;
+ }
+
+ ret = devm_regmap_add_irq_chip(rn5t618->dev, rn5t618->regmap,
+ rn5t618->irq,
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ 0, irq_chip, &rn5t618->irq_data);
+ if (ret) {
+ dev_err(rn5t618->dev, "Failed to register IRQ chip\n");
+ return ret;
+ }
+
+ return 0;
+}
+
static void rn5t618_trigger_poweroff_sequence(bool repower)
{
/* disable automatic repower-on */
@@ -106,6 +162,8 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c,
i2c_set_clientdata(i2c, priv);
priv->variant = (long)of_id->data;
+ priv->irq = i2c->irq;
+ priv->dev = &i2c->dev;
priv->regmap = devm_regmap_init_i2c(i2c, &rn5t618_regmap_config);
if (IS_ERR(priv->regmap)) {
@@ -138,6 +196,11 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c,
return ret;
}
+ if (priv->irq > 0) {
+ if (rn5t618_irq_init(priv))
+ priv->irq = 0;
+ }
+
return 0;
}
@@ -155,15 +218,40 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c)
return 0;
}
+static int __maybe_unused rn5t618_i2c_suspend(struct device *dev)
+{
+ struct rn5t618 *priv = dev_get_drvdata(dev);
+
+ if (priv->irq)
+ disable_irq(priv->irq);
+
+ return 0;
+}
+
+static int __maybe_unused rn5t618_i2c_resume(struct device *dev)
+{
+ struct rn5t618 *priv = dev_get_drvdata(dev);
+
+ if (priv->irq)
+ enable_irq(priv->irq);
+
+ return 0;
+}
+
static const struct i2c_device_id rn5t618_i2c_id[] = {
{ }
};
MODULE_DEVICE_TABLE(i2c, rn5t618_i2c_id);
+static SIMPLE_DEV_PM_OPS(rn5t618_i2c_dev_pm_ops,
+ rn5t618_i2c_suspend,
+ rn5t618_i2c_resume);
+
static struct i2c_driver rn5t618_i2c_driver = {
.driver = {
.name = "rn5t618",
.of_match_table = of_match_ptr(rn5t618_of_match),
+ .pm = &rn5t618_i2c_dev_pm_ops,
},
.probe = rn5t618_i2c_probe,
.remove = rn5t618_i2c_remove,
diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h
index d62ef48060b5..739571656f2b 100644
--- a/include/linux/mfd/rn5t618.h
+++ b/include/linux/mfd/rn5t618.h
@@ -242,9 +242,24 @@ enum {
RC5T619,
};
+/* RN5T618 IRQ definitions */
+enum {
+ RN5T618_IRQ_SYS = 0,
+ RN5T618_IRQ_DCDC,
+ RN5T618_IRQ_RTC,
+ RN5T618_IRQ_ADC,
+ RN5T618_IRQ_GPIO,
+ RN5T618_IRQ_CHG,
+ RN5T618_NR_IRQS,
+};
+
struct rn5t618 {
struct regmap *regmap;
+ struct device *dev;
long variant;
+
+ int irq;
+ struct regmap_irq_chip_data *irq_data;
};
#endif /* __LINUX_MFD_RN5T618_H */
--
2.20.1
On Fri, 13 Mar 2020, Andreas Kemnade wrote:
> This adds support for IRQ handling in the RC5T619 which is required
> for properly implementing subdevices like RTC.
> For now only definitions for the variant RC5T619 are included.
>
> Signed-off-by: Andreas Kemnade <[email protected]>
> ---
> Changes in v5:
> rn5t618_irq_init static
>
> Changes in v4:
> merge rn5t618-irq.c into rn5t618.c
> use macros for IRQ table
>
> Changes in v3:
> alignment cleanup
>
> Changes in v2:
> - no dead code, did some more testing and thinking for that
> - remove extra empty lines
> drivers/mfd/Kconfig | 1 +
> drivers/mfd/rn5t618.c | 88 +++++++++++++++++++++++++++++++++++++
> include/linux/mfd/rn5t618.h | 15 +++++++
> 3 files changed, 104 insertions(+)
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 2b203290e7b9..a7067888a41e 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1058,6 +1058,7 @@ config MFD_RN5T618
> depends on OF
> select MFD_CORE
> select REGMAP_I2C
> + select REGMAP_IRQ
> help
> Say yes here to add support for the Ricoh RN5T567,
> RN5T618, RC5T619 PMIC.
> diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c
> index ead2e79036a9..849a33d64860 100644
> --- a/drivers/mfd/rn5t618.c
> +++ b/drivers/mfd/rn5t618.c
> @@ -8,6 +8,8 @@
>
> #include <linux/delay.h>
> #include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
> #include <linux/mfd/core.h>
> #include <linux/mfd/rn5t618.h>
> #include <linux/module.h>
> @@ -46,9 +48,63 @@ static const struct regmap_config rn5t618_regmap_config = {
> .cache_type = REGCACHE_RBTREE,
> };
>
> +static const struct regmap_irq rc5t619_irqs[] = {
> + REGMAP_IRQ_REG(RN5T618_IRQ_SYS, 0, BIT(0)),
> + REGMAP_IRQ_REG(RN5T618_IRQ_DCDC, 0, BIT(1)),
> + REGMAP_IRQ_REG(RN5T618_IRQ_RTC, 0, BIT(2)),
> + REGMAP_IRQ_REG(RN5T618_IRQ_ADC, 0, BIT(3)),
> + REGMAP_IRQ_REG(RN5T618_IRQ_GPIO, 0, BIT(4)),
> + REGMAP_IRQ_REG(RN5T618_IRQ_CHG, 0, BIT(6)),
> +};
> +
> +static const struct regmap_irq_chip rc5t619_irq_chip = {
> + .name = "rc5t619",
> + .irqs = rc5t619_irqs,
> + .num_irqs = ARRAY_SIZE(rc5t619_irqs),
> + .num_regs = 1,
> + .status_base = RN5T618_INTMON,
> + .mask_base = RN5T618_INTEN,
> + .mask_invert = true,
> +};
> +
> static struct rn5t618 *rn5t618_pm_power_off;
> static struct notifier_block rn5t618_restart_handler;
>
> +static int rn5t618_irq_init(struct rn5t618 *rn5t618)
> +{
> + const struct regmap_irq_chip *irq_chip;
> + int ret;
> +
> + if (!rn5t618->irq)
> + return 0;
> +
> + switch (rn5t618->variant) {
> + case RC5T619:
> + irq_chip = &rc5t619_irq_chip;
> + break;
> + default:
> + irq_chip = NULL;
If you initialised this at the top, you can rid this line.
Don't you want to put a message in here about an unsupported device?
> + break;
> + }
> +
> + if (!irq_chip) {
> + dev_err(rn5t618->dev, "Currently no IRQ support for variant %d\n",
> + (int)rn5t618->variant);
> + return -ENOENT;
> + }
Ah yes. Put this in 'default' instead.
> + ret = devm_regmap_add_irq_chip(rn5t618->dev, rn5t618->regmap,
> + rn5t618->irq,
> + IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
> + 0, irq_chip, &rn5t618->irq_data);
> + if (ret) {
> + dev_err(rn5t618->dev, "Failed to register IRQ chip\n");
> + return ret;
Make this a one line if.
> + }
> +
> + return 0;
... and return ret.
> +}
> +
> static void rn5t618_trigger_poweroff_sequence(bool repower)
> {
> /* disable automatic repower-on */
> @@ -106,6 +162,8 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c,
>
> i2c_set_clientdata(i2c, priv);
> priv->variant = (long)of_id->data;
> + priv->irq = i2c->irq;
> + priv->dev = &i2c->dev;
>
> priv->regmap = devm_regmap_init_i2c(i2c, &rn5t618_regmap_config);
> if (IS_ERR(priv->regmap)) {
> @@ -138,6 +196,11 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c,
> return ret;
> }
>
> + if (priv->irq > 0) {
There are already have checks in rn5t618_irq_init().
Just call it regardless.
> + if (rn5t618_irq_init(priv))
If this returns an error, you should return that error from .probe().
> + priv->irq = 0;
> + }
> +
> return 0;
> }
>
> @@ -155,15 +218,40 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c)
> return 0;
> }
>
> +static int __maybe_unused rn5t618_i2c_suspend(struct device *dev)
> +{
> + struct rn5t618 *priv = dev_get_drvdata(dev);
> +
> + if (priv->irq)
> + disable_irq(priv->irq);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused rn5t618_i2c_resume(struct device *dev)
> +{
> + struct rn5t618 *priv = dev_get_drvdata(dev);
> +
> + if (priv->irq)
> + enable_irq(priv->irq);
> +
> + return 0;
> +}
> +
> static const struct i2c_device_id rn5t618_i2c_id[] = {
> { }
> };
> MODULE_DEVICE_TABLE(i2c, rn5t618_i2c_id);
>
> +static SIMPLE_DEV_PM_OPS(rn5t618_i2c_dev_pm_ops,
> + rn5t618_i2c_suspend,
> + rn5t618_i2c_resume);
> +
> static struct i2c_driver rn5t618_i2c_driver = {
> .driver = {
> .name = "rn5t618",
> .of_match_table = of_match_ptr(rn5t618_of_match),
> + .pm = &rn5t618_i2c_dev_pm_ops,
> },
> .probe = rn5t618_i2c_probe,
> .remove = rn5t618_i2c_remove,
> diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h
> index d62ef48060b5..739571656f2b 100644
> --- a/include/linux/mfd/rn5t618.h
> +++ b/include/linux/mfd/rn5t618.h
> @@ -242,9 +242,24 @@ enum {
> RC5T619,
> };
>
> +/* RN5T618 IRQ definitions */
> +enum {
> + RN5T618_IRQ_SYS = 0,
> + RN5T618_IRQ_DCDC,
> + RN5T618_IRQ_RTC,
> + RN5T618_IRQ_ADC,
> + RN5T618_IRQ_GPIO,
> + RN5T618_IRQ_CHG,
> + RN5T618_NR_IRQS,
> +};
> +
> struct rn5t618 {
> struct regmap *regmap;
> + struct device *dev;
> long variant;
> +
> + int irq;
> + struct regmap_irq_chip_data *irq_data;
> };
>
> #endif /* __LINUX_MFD_RN5T618_H */
--
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
On Thu, 19 Mar 2020 16:11:49 +0000
Lee Jones <[email protected]> wrote:
> On Fri, 13 Mar 2020, Andreas Kemnade wrote:
[...]
I agree to the other comments.
> > + if (priv->irq > 0) {
>
> There are already have checks in rn5t618_irq_init().
>
> Just call it regardless.
>
> > + if (rn5t618_irq_init(priv))
>
> If this returns an error, you should return that error from .probe().
>
Hmm, that would be a regression. Current users do not specify an interrupt
in the devicetree yet, so the MFD driver would stop working on these devices
completely.
Therefore I think we should keep the existing functionality if there is no
IRQ specified in the devicetree and ignore the error. The new subdevices
are checking the IRQ availability and give error messages and have
reduced functionality.
Regards,
Andreas
On Thu, 19 Mar 2020 16:11:49 +0000
Lee Jones <[email protected]> wrote:
[...]
>
> > + if (rn5t618_irq_init(priv))
>
> If this returns an error, you should return that error from .probe().
>
Ah, ok, I am returning 0 if there is no irq, so
forget my previous comment about regressions.
Regards,
Andreas