I'm seeing a rather odd behavior from sdhci-iproc's integration in BCM2711
(Raspberry Pi 4's SoC), and would appreciate some opinions.
The controller will timeout on SDHCI CMDs under the following conditions:
- No SD card plugged in (the card polling thread is running, CD irq disabled).
- BCM2711's VPU clock[1] configured at 500MHz or more, lower clocks are OK.
There is no specific command that will time out, it seems random.
Here's what I found out. The SDHCI controller runs at 100MHz, by bumping the
frequency to 150MHz the issue disapears. Might be pure luck, or maybe I hit the
nail and it's proper interference. Can't say.
Regards,
Nicolas
---
[1] For those who are not aware, here's the relationship between VPU's clock
and emmc2's:
osc 54000000
plld 3000000091
plld_per 750000023
emmc2 149882908
pllc 2999999988
pllc_core0 999999996
vpu 499999998
Nicolas Saenz Julienne (2):
ARM: dts: Fix-up EMMC2 controller's frequency
mmc: sdhci-iproc: Set clock frequency as per DT
arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 6 ++++++
drivers/mmc/host/sdhci-iproc.c | 10 ++++++++++
2 files changed, 16 insertions(+)
--
2.30.1
devicetree might request a clock frequency different from whatever is
set-up by the bootloader. Make sure to setup the new rate.
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
---
drivers/mmc/host/sdhci-iproc.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/mmc/host/sdhci-iproc.c b/drivers/mmc/host/sdhci-iproc.c
index ddeaf8e1f72f..536c382e2486 100644
--- a/drivers/mmc/host/sdhci-iproc.c
+++ b/drivers/mmc/host/sdhci-iproc.c
@@ -358,6 +358,16 @@ static int sdhci_iproc_probe(struct platform_device *pdev)
ret = PTR_ERR(pltfm_host->clk);
goto err;
}
+
+ if (pltfm_host->clock) {
+ ret = clk_set_rate(pltfm_host->clk, pltfm_host->clock);
+ if (ret) {
+ dev_err(dev, "failed to set host clk at %u Hz\n",
+ pltfm_host->clock);
+ goto err;
+ }
+ }
+
ret = clk_prepare_enable(pltfm_host->clk);
if (ret) {
dev_err(dev, "failed to enable host clk\n");
--
2.30.1
Force emmc2's frequency to 150MHz as the default 100MHz (set by FW)
seems to interfere with the VPU clock when setup at frequencies bigger
than 500MHz, causing unwarranted SDHCI CMD hangs when no SD card is
present.
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
---
arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
index 3b4ab947492a..9aa8408d9960 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@@ -257,6 +257,12 @@ &emmc2 {
vqmmc-supply = <&sd_io_1v8_reg>;
vmmc-supply = <&sd_vcc_reg>;
broken-cd;
+ /*
+ * Force the frequency to 150MHz as the default 100MHz seems to
+ * interfere with the VPU clock when setup at frequencies bigger than
+ * 500MHz, causing unwarranted CMD hangs.
+ */
+ clock-frequency = <150000000>;
status = "okay";
};
--
2.30.1
On Thu, 25 Feb 2021 at 10:53, Nicolas Saenz Julienne
<[email protected]> wrote:
>
> I'm seeing a rather odd behavior from sdhci-iproc's integration in BCM2711
> (Raspberry Pi 4's SoC), and would appreciate some opinions.
>
> The controller will timeout on SDHCI CMDs under the following conditions:
>
> - No SD card plugged in (the card polling thread is running, CD irq disabled).
> - BCM2711's VPU clock[1] configured at 500MHz or more, lower clocks are OK.
>
> There is no specific command that will time out, it seems random.
>
> Here's what I found out. The SDHCI controller runs at 100MHz, by bumping the
> frequency to 150MHz the issue disapears. Might be pure luck, or maybe I hit the
> nail and it's proper interference. Can't say.
As you probably know, I don't have the in-depth knowledge about this
HW. Although, let me provide a very vague guess. Could be that the
controller needs a higher clock rate to stay within some spec, for an
OPP/voltage domain for example?
In any case, assuming you get some confirmation from the Broadcom
folkz that this makes sense, you need to update the DT doc bindings
to add the clock-frequency property. In regards to this, please take
the opportunity to convert from legacy DT doc format
(brcm,sdhci-iproc.txt) into the new yaml format.
Kind regards
Uffe
>
> Regards,
> Nicolas
>
> ---
>
> [1] For those who are not aware, here's the relationship between VPU's clock
> and emmc2's:
>
> osc 54000000
> plld 3000000091
> plld_per 750000023
> emmc2 149882908
> pllc 2999999988
> pllc_core0 999999996
> vpu 499999998
>
> Nicolas Saenz Julienne (2):
> ARM: dts: Fix-up EMMC2 controller's frequency
> mmc: sdhci-iproc: Set clock frequency as per DT
>
> arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 6 ++++++
> drivers/mmc/host/sdhci-iproc.c | 10 ++++++++++
> 2 files changed, 16 insertions(+)
>
> --
> 2.30.1
>