From: Stefan Binding <[email protected]>
CS8409/CS42L42 Driver currently does most of the platform specific
setup inside the main body of the code, however, this setup can be
moved into fixup functions, to make the driver more generic.
Making the driver more generic, allows the driver to use the
cs_parse_auto_config function in the patch function. This function
forces all of the ADCs to be permanently powered, which means the
cap_sync_hook function is no longer needed to restart the stream, when
the jack has been ejected.
Since the codec is re-initialized on every init/resume, there is no
need to add specific verbs to be run on init, and instead these can
be combined with the initialization verbs, which are run on init.
In addition, the extra fixup verbs are no longer required, since this
is taken care of elsewhere.
Tested on DELL Inspiron-3505, DELL Inspiron-3501, DELL Inspiron-3500
Signed-off-by: Stefan Binding <[email protected]>
Signed-off-by: Vitaly Rodionov <[email protected]>
Changes in v1:
- No changes
---
sound/pci/hda/patch_cirrus.c | 304 ++++++++++++++---------------------
1 file changed, 118 insertions(+), 186 deletions(-)
diff --git a/sound/pci/hda/patch_cirrus.c b/sound/pci/hda/patch_cirrus.c
index 74ac758aa4d5..d0a3c3189d26 100644
--- a/sound/pci/hda/patch_cirrus.c
+++ b/sound/pci/hda/patch_cirrus.c
@@ -1292,9 +1292,14 @@ enum {
CS8409_BULLSEYE,
CS8409_WARLOCK,
CS8409_CYBORG,
- CS8409_VERBS,
+ CS8409_FIXUPS,
};
+static void cs8409_cs42l42_fixups(struct hda_codec *codec,
+ const struct hda_fixup *fix, int action);
+static int cs8409_cs42l42_exec_verb(struct hdac_device *dev,
+ unsigned int cmd, unsigned int flags, unsigned int *res);
+
/* Dell Inspiron models with cs8409/cs42l42 */
static const struct hda_model_fixup cs8409_models[] = {
{ .id = CS8409_BULLSEYE, .name = "bullseye" },
@@ -1357,6 +1362,22 @@ static const struct hda_verb cs8409_cs42l42_init_verbs[] = {
{ 0x47, AC_VERB_SET_PROC_COEF, 0x0080 }, /* I2C mode */
{ 0x47, AC_VERB_SET_COEF_INDEX, 0x005b }, /* Set I2C bus speed */
{ 0x47, AC_VERB_SET_PROC_COEF, 0x0200 }, /* 100kHz I2C_STO = 2 */
+ { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0xF0 }, /* Widget node ASP-1-TX */
+ { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x20 },
+ { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0x21 },
+ { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x04 },
+ { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0x50 }, /* Widget node ASP-1-RX0 */
+ { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x20 },
+ { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0xa1 },
+ { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x04 },
+ { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0xF0 }, /* Widget node ASP-2-TX */
+ { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x00 },
+ { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0x10 },
+ { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x90 },
+ { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0x90 }, /* Widget node DMIC-1 */
+ { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x00 },
+ { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0xA0 },
+ { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x90 },
{} /* terminator */
};
@@ -1368,48 +1389,28 @@ static const struct hda_pintbl cs8409_cs42l42_pincfgs[] = {
{} /* terminator */
};
-static const struct hda_verb cs8409_cs42l42_add_verbs[] = {
- { 0x24, 0x71c, 0xF0 }, /* Widget node ASP-1-TX */
- { 0x24, 0x71d, 0x20 },
- { 0x24, 0x71e, 0x21 },
- { 0x24, 0x71f, 0x04 },
- { 0x34, 0x71c, 0x50 }, /* Widget node ASP-1-RX0 */
- { 0x34, 0x71d, 0x20 },
- { 0x34, 0x71e, 0xa1 },
- { 0x34, 0x71f, 0x04 },
- { 0x2C, 0x71c, 0xF0 }, /* Widget node ASP-2-TX */
- { 0x2C, 0x71d, 0x00 },
- { 0x2C, 0x71e, 0x10 },
- { 0x2C, 0x71f, 0x90 },
- { 0x44, 0x71c, 0x90 }, /* Widget node DMIC-1 */
- { 0x44, 0x71d, 0x00 },
- { 0x44, 0x71e, 0xA0 },
- { 0x44, 0x71f, 0x90 },
- {} /* terminator */
-};
-
static const struct hda_fixup cs8409_fixups[] = {
[CS8409_BULLSEYE] = {
.type = HDA_FIXUP_PINS,
.v.pins = cs8409_cs42l42_pincfgs,
.chained = true,
- .chain_id = CS8409_VERBS,
+ .chain_id = CS8409_FIXUPS,
},
[CS8409_WARLOCK] = {
.type = HDA_FIXUP_PINS,
.v.pins = cs8409_cs42l42_pincfgs,
.chained = true,
- .chain_id = CS8409_VERBS,
+ .chain_id = CS8409_FIXUPS,
},
[CS8409_CYBORG] = {
.type = HDA_FIXUP_PINS,
.v.pins = cs8409_cs42l42_pincfgs,
.chained = true,
- .chain_id = CS8409_VERBS,
+ .chain_id = CS8409_FIXUPS,
},
- [CS8409_VERBS] = {
- .type = HDA_FIXUP_VERBS,
- .v.verbs = cs8409_cs42l42_add_verbs,
+ [CS8409_FIXUPS] = {
+ .type = HDA_FIXUP_FUNC,
+ .v.func = cs8409_cs42l42_fixups,
},
};
@@ -1975,26 +1976,6 @@ static void cs8409_jack_unsol_event(struct hda_codec *codec, unsigned int res)
}
}
-static int cs8409_cs42l42_build_controls(struct hda_codec *codec)
-{
- int err;
-
- err = snd_hda_gen_build_controls(codec);
- if (err < 0)
- return err;
-
- snd_hda_apply_fixup(codec, HDA_FIXUP_ACT_BUILD);
-
- /* Run jack auto detect first time on boot
- * after controls have been added, to check if jack has
- * been already plugged in
- */
- cs8409_cs42l42_run_jack_detect(codec);
- usleep_range(100000, 150000);
-
- return 0;
-}
-
#ifdef CONFIG_PM
/* Manage PDREF, when transition to D3hot */
static int cs8409_suspend(struct hda_codec *codec)
@@ -2015,31 +1996,6 @@ static int cs8409_suspend(struct hda_codec *codec)
}
#endif
-static void cs8409_cs42l42_cap_sync_hook(struct hda_codec *codec,
- struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_value *ucontrol)
-{
- struct cs_spec *spec = codec->spec;
- unsigned int curval, expval;
- /* CS8409 DMIC Pin only allows the setting of the Stream Parameters in
- * Power State D0. When a headset is unplugged, and the path is switched to
- * the DMIC, the Stream is restarted with the new ADC, but this is done in
- * Power State D3. Restart the Stream now DMIC is in D0.
- */
- if (spec->gen.cur_adc == CS8409_CS42L42_DMIC_ADC_PIN_NID) {
- curval = snd_hda_codec_read(codec, spec->gen.cur_adc,
- 0, AC_VERB_GET_CONV, 0);
- expval = (spec->gen.cur_adc_stream_tag << 4) | 0;
- if (curval != expval) {
- codec_dbg(codec, "%s Restarting Stream after DMIC switch\n", __func__);
- __snd_hda_codec_cleanup_stream(codec, spec->gen.cur_adc, 1);
- snd_hda_codec_setup_stream(codec, spec->gen.cur_adc,
- spec->gen.cur_adc_stream_tag, 0,
- spec->gen.cur_adc_format);
- }
- }
-}
-
/* Enable/Disable Unsolicited Response for gpio(s) 3,4 */
static void cs8409_enable_ur(struct hda_codec *codec, int flag)
{
@@ -2123,25 +2079,14 @@ static int cs8409_cs42l42_init(struct hda_codec *codec)
{
int ret = snd_hda_gen_init(codec);
- if (!ret) {
- /* On Dell platforms with suspend D3 mode support we
- * have to re-initialise cs8409 bridge and companion
- * cs42l42 codec
- */
- snd_hda_sequence_write(codec, cs8409_cs42l42_init_verbs);
- snd_hda_sequence_write(codec, cs8409_cs42l42_add_verbs);
-
- cs8409_cs42l42_hw_init(codec);
-
- cs8409_cs42l42_run_jack_detect(codec);
- usleep_range(100000, 150000);
- }
+ if (!ret)
+ snd_hda_apply_fixup(codec, HDA_FIXUP_ACT_INIT);
return ret;
}
static const struct hda_codec_ops cs8409_cs42l42_patch_ops = {
- .build_controls = cs8409_cs42l42_build_controls,
+ .build_controls = cs_build_controls,
.build_pcms = snd_hda_gen_build_pcms,
.init = cs8409_cs42l42_init,
.free = cs_free,
@@ -2151,70 +2096,95 @@ static const struct hda_codec_ops cs8409_cs42l42_patch_ops = {
#endif
};
-static int cs8409_cs42l42_fixup(struct hda_codec *codec)
+static void cs8409_cs42l42_fixups(struct hda_codec *codec,
+ const struct hda_fixup *fix, int action)
{
- int err;
struct cs_spec *spec = codec->spec;
int caps;
- /* Basic initial sequence for specific hw configuration */
- snd_hda_sequence_write(codec, cs8409_cs42l42_init_verbs);
-
- /* CS8409 is simple HDA bridge and intended to be used with a remote
- * companion codec. Most of input/output PIN(s) have only basic
- * capabilities. NID(s) 0x24 and 0x34 have only OUTC and INC
- * capabilities and no presence detect capable (PDC) and call to
- * snd_hda_gen_build_controls() will mark them as non detectable
- * phantom jacks. However, in this configuration companion codec
- * CS42L42 is connected to these pins and it has jack detect
- * capabilities. We have to override pin capabilities,
- * otherwise they will not be created as input devices.
- */
- caps = snd_hdac_read_parm(&codec->core, CS8409_CS42L42_HP_PIN_NID,
- AC_PAR_PIN_CAP);
- if (caps >= 0)
- snd_hdac_override_parm(&codec->core,
- CS8409_CS42L42_HP_PIN_NID, AC_PAR_PIN_CAP,
- (caps | (AC_PINCAP_IMP_SENSE | AC_PINCAP_PRES_DETECT)));
-
- caps = snd_hdac_read_parm(&codec->core, CS8409_CS42L42_AMIC_PIN_NID,
- AC_PAR_PIN_CAP);
- if (caps >= 0)
- snd_hdac_override_parm(&codec->core,
- CS8409_CS42L42_AMIC_PIN_NID, AC_PAR_PIN_CAP,
- (caps | (AC_PINCAP_IMP_SENSE | AC_PINCAP_PRES_DETECT)));
-
- caps = get_wcaps(codec, CS8409_CS42L42_HP_PIN_NID);
- if (caps != 0)
- snd_hda_override_wcaps(codec, CS8409_CS42L42_HP_PIN_NID,
- (caps | AC_WCAP_UNSOL_CAP));
-
- caps = get_wcaps(codec, CS8409_CS42L42_AMIC_PIN_NID);
- if (caps != 0)
- snd_hda_override_wcaps(codec, CS8409_CS42L42_AMIC_PIN_NID,
- (caps | AC_WCAP_UNSOL_CAP));
+ switch (action) {
+ case HDA_FIXUP_ACT_PRE_PROBE:
+ snd_hda_add_verbs(codec, cs8409_cs42l42_init_verbs);
+ /* verb exec op override */
+ spec->exec_verb = codec->core.exec_verb;
+ codec->core.exec_verb = cs8409_cs42l42_exec_verb;
- snd_hda_apply_fixup(codec, HDA_FIXUP_ACT_PRE_PROBE);
+ mutex_init(&spec->cs8409_i2c_mux);
- err = snd_hda_parse_pin_defcfg(codec, &spec->gen.autocfg, 0, 0);
- if (err < 0)
- return err;
+ codec->patch_ops = cs8409_cs42l42_patch_ops;
- err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
- if (err < 0)
- return err;
+ spec->gen.suppress_auto_mute = 1;
+ spec->gen.no_primary_hp = 1;
+ spec->gen.suppress_vmaster = 1;
- if (!snd_hda_gen_add_kctl(
- &spec->gen, NULL, &cs8409_cs42l42_hp_volume_mixer))
- return -1;
+ /* GPIO 5 out, 3,4 in */
+ spec->gpio_dir = GPIO5_INT;
+ spec->gpio_data = 0;
+ spec->gpio_mask = 0x03f;
- if (!snd_hda_gen_add_kctl(
- &spec->gen, NULL, &cs8409_cs42l42_amic_volume_mixer))
- return -1;
+ spec->cs42l42_hp_jack_in = 0;
+ spec->cs42l42_mic_jack_in = 0;
- snd_hda_apply_fixup(codec, HDA_FIXUP_ACT_PROBE);
+ /* Basic initial sequence for specific hw configuration */
+ snd_hda_sequence_write(codec, cs8409_cs42l42_init_verbs);
- return 0;
+ /* CS8409 is simple HDA bridge and intended to be used with a remote
+ * companion codec. Most of input/output PIN(s) have only basic
+ * capabilities. NID(s) 0x24 and 0x34 have only OUTC and INC
+ * capabilities and no presence detect capable (PDC) and call to
+ * snd_hda_gen_build_controls() will mark them as non detectable
+ * phantom jacks. However, in this configuration companion codec
+ * CS42L42 is connected to these pins and it has jack detect
+ * capabilities. We have to override pin capabilities,
+ * otherwise they will not be created as input devices.
+ */
+ caps = snd_hdac_read_parm(&codec->core, CS8409_CS42L42_HP_PIN_NID,
+ AC_PAR_PIN_CAP);
+ if (caps >= 0)
+ snd_hdac_override_parm(&codec->core,
+ CS8409_CS42L42_HP_PIN_NID, AC_PAR_PIN_CAP,
+ (caps | (AC_PINCAP_IMP_SENSE | AC_PINCAP_PRES_DETECT)));
+
+ caps = snd_hdac_read_parm(&codec->core, CS8409_CS42L42_AMIC_PIN_NID,
+ AC_PAR_PIN_CAP);
+ if (caps >= 0)
+ snd_hdac_override_parm(&codec->core,
+ CS8409_CS42L42_AMIC_PIN_NID, AC_PAR_PIN_CAP,
+ (caps | (AC_PINCAP_IMP_SENSE | AC_PINCAP_PRES_DETECT)));
+
+ caps = get_wcaps(codec, CS8409_CS42L42_HP_PIN_NID);
+ if (caps != 0)
+ snd_hda_override_wcaps(codec, CS8409_CS42L42_HP_PIN_NID,
+ (caps | AC_WCAP_UNSOL_CAP));
+
+ caps = get_wcaps(codec, CS8409_CS42L42_AMIC_PIN_NID);
+ if (caps != 0)
+ snd_hda_override_wcaps(codec, CS8409_CS42L42_AMIC_PIN_NID,
+ (caps | AC_WCAP_UNSOL_CAP));
+ break;
+ case HDA_FIXUP_ACT_PROBE:
+ snd_hda_gen_add_kctl(&spec->gen,
+ NULL, &cs8409_cs42l42_hp_volume_mixer);
+ snd_hda_gen_add_kctl(&spec->gen,
+ NULL, &cs8409_cs42l42_amic_volume_mixer);
+ cs8409_cs42l42_hw_init(codec);
+ snd_hda_codec_set_name(codec, "CS8409/CS42L42");
+ break;
+ case HDA_FIXUP_ACT_INIT:
+ cs8409_cs42l42_hw_init(codec);
+ // Fall through
+ case HDA_FIXUP_ACT_BUILD:
+ /* Run jack auto detect first time on boot
+ * after controls have been added, to check if jack has
+ * been already plugged in.
+ * Run immediately after init.
+ */
+ cs8409_cs42l42_run_jack_detect(codec);
+ usleep_range(100000, 150000);
+ break;
+ default:
+ break;
+ }
}
static int cs8409_cs42l42_exec_verb(struct hdac_device *dev,
@@ -2255,11 +2225,9 @@ static int cs8409_cs42l42_exec_verb(struct hdac_device *dev,
static int patch_cs8409(struct hda_codec *codec)
{
- struct cs_spec *spec;
- int err = -EINVAL;
+ int err;
- spec = cs_alloc_spec(codec, CS8409_VENDOR_NID);
- if (!spec)
+ if (!cs_alloc_spec(codec, CS8409_VENDOR_NID))
return -ENOMEM;
snd_hda_pick_fixup(codec,
@@ -2270,52 +2238,16 @@ static int patch_cs8409(struct hda_codec *codec)
codec->bus->pci->subsystem_vendor,
codec->bus->pci->subsystem_device);
- switch (codec->fixup_id) {
- /* Dell platforms with CS42L42 companion codec */
- case CS8409_BULLSEYE:
- case CS8409_WARLOCK:
- case CS8409_CYBORG:
-
- snd_hda_add_verbs(codec, cs8409_cs42l42_add_verbs);
-
- /* verb exec op override */
- spec->exec_verb = codec->core.exec_verb;
- codec->core.exec_verb = cs8409_cs42l42_exec_verb;
-
- mutex_init(&spec->cs8409_i2c_mux);
-
- codec->patch_ops = cs8409_cs42l42_patch_ops;
-
- spec->gen.cap_sync_hook = cs8409_cs42l42_cap_sync_hook;
-
- spec->gen.suppress_auto_mute = 1;
- spec->gen.no_primary_hp = 1;
- spec->gen.suppress_vmaster = 1;
- /* GPIO 5 out, 3,4 in */
- spec->gpio_dir = GPIO5_INT;
- spec->gpio_data = 0;
- spec->gpio_mask = 0x03f;
-
- spec->cs42l42_hp_jack_in = 0;
- spec->cs42l42_mic_jack_in = 0;
-
- err = cs8409_cs42l42_fixup(codec);
- break;
-
- default:
- codec_err(codec, "VID=%08x, DEV=%08x not supported\n",
- codec->bus->pci->subsystem_vendor,
- codec->bus->pci->subsystem_device);
- break;
- }
+ snd_hda_apply_fixup(codec, HDA_FIXUP_ACT_PRE_PROBE);
- if (!err) {
- cs8409_cs42l42_hw_init(codec);
- snd_hda_codec_set_name(codec, "CS8409/CS42L42");
- } else
+ err = cs_parse_auto_config(codec);
+ if (err < 0) {
cs_free(codec);
+ return err;
+ }
- return err;
+ snd_hda_apply_fixup(codec, HDA_FIXUP_ACT_PROBE);
+ return 0;
}
/*
--
2.25.1
On Sat, 13 Mar 2021 12:34:10 +0100,
Vitaly Rodionov wrote:
> @@ -1357,6 +1362,22 @@ static const struct hda_verb cs8409_cs42l42_init_verbs[] = {
> { 0x47, AC_VERB_SET_PROC_COEF, 0x0080 }, /* I2C mode */
> { 0x47, AC_VERB_SET_COEF_INDEX, 0x005b }, /* Set I2C bus speed */
> { 0x47, AC_VERB_SET_PROC_COEF, 0x0200 }, /* 100kHz I2C_STO = 2 */
> + { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0xF0 }, /* Widget node ASP-1-TX */
> + { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x20 },
> + { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0x21 },
> + { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x04 },
> + { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0x50 }, /* Widget node ASP-1-RX0 */
> + { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x20 },
> + { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0xa1 },
> + { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x04 },
> + { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0xF0 }, /* Widget node ASP-2-TX */
> + { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x00 },
> + { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0x10 },
> + { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x90 },
> + { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0x90 }, /* Widget node DMIC-1 */
> + { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x00 },
> + { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0xA0 },
> + { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x90 },
Those widgets are all pin widgets, right? If so, setting via the
pincfg table would be more suitable, as it's cached and exposed via
sysfs for debugging.
thanks,
Takashi
On 15/03/2021 7:49 am, Takashi Iwai wrote:
> On Sat, 13 Mar 2021 12:34:10 +0100,
> Vitaly Rodionov wrote:
>> @@ -1357,6 +1362,22 @@ static const struct hda_verb cs8409_cs42l42_init_verbs[] = {
>> { 0x47, AC_VERB_SET_PROC_COEF, 0x0080 }, /* I2C mode */
>> { 0x47, AC_VERB_SET_COEF_INDEX, 0x005b }, /* Set I2C bus speed */
>> { 0x47, AC_VERB_SET_PROC_COEF, 0x0200 }, /* 100kHz I2C_STO = 2 */
>> + { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0xF0 }, /* Widget node ASP-1-TX */
>> + { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x20 },
>> + { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0x21 },
>> + { 0x24, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x04 },
>> + { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0x50 }, /* Widget node ASP-1-RX0 */
>> + { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x20 },
>> + { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0xa1 },
>> + { 0x34, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x04 },
>> + { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0xF0 }, /* Widget node ASP-2-TX */
>> + { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x00 },
>> + { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0x10 },
>> + { 0x2C, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x90 },
>> + { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_0, 0x90 }, /* Widget node DMIC-1 */
>> + { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_1, 0x00 },
>> + { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_2, 0xA0 },
>> + { 0x44, AC_VERB_SET_CONFIG_DEFAULT_BYTES_3, 0x90 },
> Those widgets are all pin widgets, right? If so, setting via the
> pincfg table would be more suitable, as it's cached and exposed via
> sysfs for debugging.
Yes, you are right, actually we already have these widgets in pincfg
table, so this code is redundant.
Will fix in next version.
>
>
> thanks,
>
> Takashi