2021-12-05 22:12:23

by David Virag

[permalink] [raw]
Subject: [PATCH v2 0/7] Initial Samsung Galaxy A8 (2018) support

Add basic initial support for the Samsung Galaxy A8 (2018) smartphone.
This phone is also known as "jackpotlte" and under the model name
"SM-A530F". In its current state this should work on most if not all
Exynos7885 phones/devices released.

As of now, it supports I2C nodes (all disabled by default) and UART
console with basic clock support in place.

To access the UART console on the A8, there are two methods:
-You can open up the device and solder directly to some debug pins
close to the display connector.
-Through I2C you can set the S2MU004 MFD chip to multiplex the SoC's
UART lines to the d+ and d- on the USB Type-C port of the device.

Note that UART works on 1.8 volts, so plugging in a normal USB cable
while multiplexed to UART may fry the SoC.

Everything was tested through UART by using a minimal driver that sets
the S2MU004 to multiplex UART.

The preferred way to boot this device is by using my Minimal S-Boot
Wrapper [1] to work around some issues caused by the stock, and
non-replacable Samsung S-Boot bootloader.

Changes in v2:
- Added R-b tags by Krzysztof Kozlowski
- Moved dt-bindings patches to the beginning of the series
- Fixed double : in 7885 CMU bindings
- Fixed multiple double line breaks
- Made Exynos850 and 7885 clock drivers share some code in a new patch
- Lots of dts/dtsi fixes

[1] https://github.com/VDavid003/minimal_sboot_wrapper

David Virag (7):
dt-bindings: clock: Add bindings definitions for Exynos7885 CMU
dt-bindings: clock: Document Exynos7885 CMU bindings
dt-bindings: arm: samsung: document jackpotlte board binding
clk: samsung: Make exynos850_register_cmu shared
clk: samsung: clk-pll: Add support for pll1417x
clk: samsung: Add initial Exynos7885 clock driver
arm64: dts: exynos: Add initial device tree support for Exynos7885 SoC

.../bindings/arm/samsung/samsung-boards.yaml | 6 +
.../clock/samsung,exynos7885-clock.yaml | 166 ++++
arch/arm64/boot/dts/exynos/Makefile | 7 +-
.../boot/dts/exynos/exynos7885-jackpotlte.dts | 95 ++
.../boot/dts/exynos/exynos7885-pinctrl.dtsi | 865 ++++++++++++++++++
arch/arm64/boot/dts/exynos/exynos7885.dtsi | 438 +++++++++
drivers/clk/samsung/Makefile | 2 +
drivers/clk/samsung/clk-exynos-arm64.c | 94 ++
drivers/clk/samsung/clk-exynos-arm64.h | 20 +
drivers/clk/samsung/clk-exynos7885.c | 593 ++++++++++++
drivers/clk/samsung/clk-exynos850.c | 94 +-
drivers/clk/samsung/clk-pll.c | 1 +
drivers/clk/samsung/clk-pll.h | 1 +
include/dt-bindings/clock/exynos7885.h | 115 +++
14 files changed, 2404 insertions(+), 93 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/samsung,exynos7885-clock.yaml
create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
create mode 100644 arch/arm64/boot/dts/exynos/exynos7885.dtsi
create mode 100644 drivers/clk/samsung/clk-exynos-arm64.c
create mode 100644 drivers/clk/samsung/clk-exynos-arm64.h
create mode 100644 drivers/clk/samsung/clk-exynos7885.c
create mode 100644 include/dt-bindings/clock/exynos7885.h

--
2.34.1



2021-12-05 22:12:28

by David Virag

[permalink] [raw]
Subject: [PATCH v2 1/7] dt-bindings: clock: Add bindings definitions for Exynos7885 CMU

Just like on Exynos850, the clock controller driver is designed to have
separate instances for each particular CMU, so clock IDs start from 1
for each CMU in this bindings header too.

Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: David Virag <[email protected]>
---
Changes in v2:
- Added R-b tag by Krzysztof Kozlowski

include/dt-bindings/clock/exynos7885.h | 115 +++++++++++++++++++++++++
1 file changed, 115 insertions(+)
create mode 100644 include/dt-bindings/clock/exynos7885.h

diff --git a/include/dt-bindings/clock/exynos7885.h b/include/dt-bindings/clock/exynos7885.h
new file mode 100644
index 000000000000..1f8701691d62
--- /dev/null
+++ b/include/dt-bindings/clock/exynos7885.h
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) 2021 Dávid Virág
+ *
+ * Device Tree binding constants for Exynos7885 clock controller.
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_EXYNOS_7885_H
+#define _DT_BINDINGS_CLOCK_EXYNOS_7885_H
+
+/* CMU_TOP */
+#define CLK_FOUT_SHARED0_PLL 1
+#define CLK_FOUT_SHARED1_PLL 2
+#define CLK_DOUT_SHARED0_DIV2 3
+#define CLK_DOUT_SHARED0_DIV3 4
+#define CLK_DOUT_SHARED0_DIV4 5
+#define CLK_DOUT_SHARED0_DIV5 6
+#define CLK_DOUT_SHARED1_DIV2 7
+#define CLK_DOUT_SHARED1_DIV3 8
+#define CLK_DOUT_SHARED1_DIV4 9
+#define CLK_MOUT_CORE_BUS 10
+#define CLK_MOUT_CORE_CCI 11
+#define CLK_MOUT_CORE_G3D 12
+#define CLK_DOUT_CORE_BUS 13
+#define CLK_DOUT_CORE_CCI 14
+#define CLK_DOUT_CORE_G3D 15
+#define CLK_GOUT_CORE_BUS 16
+#define CLK_GOUT_CORE_CCI 17
+#define CLK_GOUT_CORE_G3D 18
+#define CLK_MOUT_PERI_BUS 19
+#define CLK_MOUT_PERI_SPI0 20
+#define CLK_MOUT_PERI_SPI1 21
+#define CLK_MOUT_PERI_UART0 22
+#define CLK_MOUT_PERI_UART1 23
+#define CLK_MOUT_PERI_UART2 24
+#define CLK_MOUT_PERI_USI0 25
+#define CLK_MOUT_PERI_USI1 26
+#define CLK_MOUT_PERI_USI2 27
+#define CLK_DOUT_PERI_BUS 28
+#define CLK_DOUT_PERI_SPI0 29
+#define CLK_DOUT_PERI_SPI1 30
+#define CLK_DOUT_PERI_UART0 31
+#define CLK_DOUT_PERI_UART1 32
+#define CLK_DOUT_PERI_UART2 33
+#define CLK_DOUT_PERI_USI0 34
+#define CLK_DOUT_PERI_USI1 35
+#define CLK_DOUT_PERI_USI2 36
+#define CLK_GOUT_PERI_BUS 37
+#define CLK_GOUT_PERI_SPI0 38
+#define CLK_GOUT_PERI_SPI1 39
+#define CLK_GOUT_PERI_UART0 40
+#define CLK_GOUT_PERI_UART1 41
+#define CLK_GOUT_PERI_UART2 42
+#define CLK_GOUT_PERI_USI0 43
+#define CLK_GOUT_PERI_USI1 44
+#define CLK_GOUT_PERI_USI2 45
+#define TOP_NR_CLK 46
+
+/* CMU_CORE */
+#define CLK_MOUT_CORE_BUS_USER 1
+#define CLK_MOUT_CORE_CCI_USER 2
+#define CLK_MOUT_CORE_G3D_USER 3
+#define CLK_MOUT_CORE_GIC 4
+#define CLK_DOUT_CORE_BUSP 5
+#define CLK_GOUT_CCI_ACLK 6
+#define CLK_GOUT_GIC400_CLK 7
+#define CORE_NR_CLK 8
+
+/* CMU_PERI */
+#define CLK_MOUT_PERI_BUS_USER 1
+#define CLK_MOUT_PERI_SPI0_USER 2
+#define CLK_MOUT_PERI_SPI1_USER 3
+#define CLK_MOUT_PERI_UART0_USER 4
+#define CLK_MOUT_PERI_UART1_USER 5
+#define CLK_MOUT_PERI_UART2_USER 6
+#define CLK_MOUT_PERI_USI0_USER 7
+#define CLK_MOUT_PERI_USI1_USER 8
+#define CLK_MOUT_PERI_USI2_USER 9
+#define CLK_GOUT_GPIO_TOP_PCLK 10
+#define CLK_GOUT_HSI2C0_PCLK 11
+#define CLK_GOUT_HSI2C1_PCLK 12
+#define CLK_GOUT_HSI2C2_PCLK 13
+#define CLK_GOUT_HSI2C3_PCLK 14
+#define CLK_GOUT_I2C0_PCLK 15
+#define CLK_GOUT_I2C1_PCLK 16
+#define CLK_GOUT_I2C2_PCLK 17
+#define CLK_GOUT_I2C3_PCLK 18
+#define CLK_GOUT_I2C4_PCLK 19
+#define CLK_GOUT_I2C5_PCLK 20
+#define CLK_GOUT_I2C6_PCLK 21
+#define CLK_GOUT_I2C7_PCLK 22
+#define CLK_GOUT_PWM_MOTOR_PCLK 23
+#define CLK_GOUT_SPI0_PCLK 24
+#define CLK_GOUT_SPI0_EXT_CLK 25
+#define CLK_GOUT_SPI1_PCLK 26
+#define CLK_GOUT_SPI1_EXT_CLK 27
+#define CLK_GOUT_UART0_EXT_UCLK 28
+#define CLK_GOUT_UART0_PCLK 29
+#define CLK_GOUT_UART1_EXT_UCLK 30
+#define CLK_GOUT_UART1_PCLK 31
+#define CLK_GOUT_UART2_EXT_UCLK 32
+#define CLK_GOUT_UART2_PCLK 33
+#define CLK_GOUT_USI0_PCLK 34
+#define CLK_GOUT_USI0_SCLK 35
+#define CLK_GOUT_USI1_PCLK 36
+#define CLK_GOUT_USI1_SCLK 37
+#define CLK_GOUT_USI2_PCLK 38
+#define CLK_GOUT_USI2_SCLK 39
+#define CLK_GOUT_MCT_PCLK 40
+#define CLK_GOUT_SYSREG_PERI_PCLK 41
+#define CLK_GOUT_WDT0_PCLK 42
+#define CLK_GOUT_WDT1_PCLK 43
+#define PERI_NR_CLK 44
+
+#endif /* _DT_BINDINGS_CLOCK_EXYNOS_7885_H */
--
2.34.1


2021-12-05 22:12:32

by David Virag

[permalink] [raw]
Subject: [PATCH v2 2/7] dt-bindings: clock: Document Exynos7885 CMU bindings

Provide dt-schema documentation for Exynos7885 SoC clock controller.
Description is modified from Exynos850 clock controller documentation as
I couldn't describe it any better, that was written by Sam Protsenko.

Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: David Virag <[email protected]>
---
Changes in v2:
- Fixed double : in description
- Added R-b tag by Krzysztof Kozlowski

.../clock/samsung,exynos7885-clock.yaml | 166 ++++++++++++++++++
1 file changed, 166 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/samsung,exynos7885-clock.yaml

diff --git a/Documentation/devicetree/bindings/clock/samsung,exynos7885-clock.yaml b/Documentation/devicetree/bindings/clock/samsung,exynos7885-clock.yaml
new file mode 100644
index 000000000000..63f95d6ec190
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/samsung,exynos7885-clock.yaml
@@ -0,0 +1,166 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/samsung,exynos7885-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos7885 SoC clock controller
+
+maintainers:
+ - Dávid Virág <[email protected]>
+ - Chanwoo Choi <[email protected]>
+ - Krzysztof Kozlowski <[email protected]>
+ - Sylwester Nawrocki <[email protected]>
+ - Tomasz Figa <[email protected]>
+
+description: |
+ Exynos7885 clock controller is comprised of several CMU units, generating
+ clocks for different domains. Those CMU units are modeled as separate device
+ tree nodes, and might depend on each other. The root clock in that root tree
+ is an external clock: OSCCLK (26 MHz). This external clock must be defined
+ as a fixed-rate clock in dts.
+
+ CMU_TOP is a top-level CMU, where all base clocks are prepared using PLLs and
+ dividers; all other leaf clocks (other CMUs) are usually derived from CMU_TOP.
+
+ Each clock is assigned an identifier and client nodes can use this identifier
+ to specify the clock which they consume. All clocks available for usage
+ in clock consumer nodes are defined as preprocessor macros in
+ 'dt-bindings/clock/exynos7885.h' header.
+
+properties:
+ compatible:
+ enum:
+ - samsung,exynos7885-cmu-top
+ - samsung,exynos7885-cmu-core
+ - samsung,exynos7885-cmu-peri
+
+ clocks:
+ minItems: 1
+ maxItems: 10
+
+ clock-names:
+ minItems: 1
+ maxItems: 10
+
+ "#clock-cells":
+ const: 1
+
+ reg:
+ maxItems: 1
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: samsung,exynos7885-cmu-top
+
+ then:
+ properties:
+ clocks:
+ items:
+ - description: External reference clock (26 MHz)
+
+ clock-names:
+ items:
+ - const: oscclk
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: samsung,exynos7885-cmu-core
+
+ then:
+ properties:
+ clocks:
+ items:
+ - description: External reference clock (26 MHz)
+ - description: CMU_CORE bus clock (from CMU_TOP)
+ - description: CCI clock (from CMU_TOP)
+ - description: G3D clock (from CMU_TOP)
+
+ clock-names:
+ items:
+ - const: oscclk
+ - const: dout_core_bus
+ - const: dout_core_cci
+ - const: dout_core_g3d
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: samsung,exynos7885-cmu-peri
+
+ then:
+ properties:
+ clocks:
+ items:
+ - description: External reference clock (26 MHz)
+ - description: CMU_PERI bus clock (from CMU_TOP)
+ - description: SPI0 clock (from CMU_TOP)
+ - description: SPI1 clock (from CMU_TOP)
+ - description: UART0 clock (from CMU_TOP)
+ - description: UART1 clock (from CMU_TOP)
+ - description: UART2 clock (from CMU_TOP)
+ - description: USI0 clock (from CMU_TOP)
+ - description: USI1 clock (from CMU_TOP)
+ - description: USI2 clock (from CMU_TOP)
+
+ clock-names:
+ items:
+ - const: oscclk
+ - const: dout_peri_bus
+ - const: dout_peri_spi0
+ - const: dout_peri_spi1
+ - const: dout_peri_uart0
+ - const: dout_peri_uart1
+ - const: dout_peri_uart2
+ - const: dout_peri_usi0
+ - const: dout_peri_usi1
+ - const: dout_peri_usi2
+
+required:
+ - compatible
+ - "#clock-cells"
+ - clocks
+ - clock-names
+ - reg
+
+additionalProperties: false
+
+examples:
+ # Clock controller node for CMU_PERI
+ - |
+ #include <dt-bindings/clock/exynos7885.h>
+
+ cmu_peri: clock-controller@0x10010000 {
+ compatible = "samsung,exynos7885-cmu-peri";
+ reg = <0x10010000 0x8000>;
+ #clock-cells = <1>;
+
+ clocks = <&oscclk>,
+ <&cmu_top CLK_DOUT_PERI_BUS>,
+ <&cmu_top CLK_DOUT_PERI_SPI0>,
+ <&cmu_top CLK_DOUT_PERI_SPI1>,
+ <&cmu_top CLK_DOUT_PERI_UART0>,
+ <&cmu_top CLK_DOUT_PERI_UART1>,
+ <&cmu_top CLK_DOUT_PERI_UART2>,
+ <&cmu_top CLK_DOUT_PERI_USI0>,
+ <&cmu_top CLK_DOUT_PERI_USI1>,
+ <&cmu_top CLK_DOUT_PERI_USI2>;
+ clock-names = "oscclk",
+ "dout_peri_bus",
+ "dout_peri_spi0",
+ "dout_peri_spi1",
+ "dout_peri_uart0",
+ "dout_peri_uart1",
+ "dout_peri_uart2",
+ "dout_peri_usi0",
+ "dout_peri_usi1",
+ "dout_peri_usi2";
+ };
+
+...
--
2.34.1


2021-12-05 22:12:37

by David Virag

[permalink] [raw]
Subject: [PATCH v2 3/7] dt-bindings: arm: samsung: document jackpotlte board binding

Add binding for the jackpotlte board (Samsung Galaxy A8 (2018)).

Signed-off-by: David Virag <[email protected]>
---
Changes in v2:
- Nothing

.../devicetree/bindings/arm/samsung/samsung-boards.yaml | 6 ++++++
1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
index ef6dc14be4b5..d88571202713 100644
--- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
+++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.yaml
@@ -199,6 +199,12 @@ properties:
- samsung,exynos7-espresso # Samsung Exynos7 Espresso
- const: samsung,exynos7

+ - description: Exynos7885 based boards
+ items:
+ - enum:
+ - samsung,jackpotlte # Samsung Galaxy A8 (2018)
+ - const: samsung,exynos7885
+
- description: Exynos Auto v9 based boards
items:
- enum:
--
2.34.1


2021-12-05 22:12:44

by David Virag

[permalink] [raw]
Subject: [PATCH v2 4/7] clk: samsung: Make exynos850_register_cmu shared

Rename exynos850_register_cmu to exynos_arm64_register_cmu and move it
to a new file called "clk-exynos-arm64.c".

This should have no functional changes, but it will allow this code to
be shared between other arm64 Exynos SoCs, like the Exynos7885 and
possibly ExynosAuto V9.

Signed-off-by: David Virag <[email protected]>
---
Changes in v2:
- New patch

drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-exynos-arm64.c | 94 ++++++++++++++++++++++++++
drivers/clk/samsung/clk-exynos-arm64.h | 20 ++++++
drivers/clk/samsung/clk-exynos850.c | 94 ++------------------------
4 files changed, 119 insertions(+), 90 deletions(-)
create mode 100644 drivers/clk/samsung/clk-exynos-arm64.c
create mode 100644 drivers/clk/samsung/clk-exynos-arm64.h

diff --git a/drivers/clk/samsung/Makefile b/drivers/clk/samsung/Makefile
index c46cf11e4d0b..901e6333c5f0 100644
--- a/drivers/clk/samsung/Makefile
+++ b/drivers/clk/samsung/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_EXYNOS_5420_COMMON_CLK) += clk-exynos5-subcmu.o
obj-$(CONFIG_EXYNOS_ARM64_COMMON_CLK) += clk-exynos5433.o
obj-$(CONFIG_EXYNOS_AUDSS_CLK_CON) += clk-exynos-audss.o
obj-$(CONFIG_EXYNOS_CLKOUT) += clk-exynos-clkout.o
+obj-$(CONFIG_EXYNOS_ARM64_COMMON_CLK) += clk-exynos-arm64.o
obj-$(CONFIG_EXYNOS_ARM64_COMMON_CLK) += clk-exynos7.o
obj-$(CONFIG_EXYNOS_ARM64_COMMON_CLK) += clk-exynos850.o
obj-$(CONFIG_S3C2410_COMMON_CLK)+= clk-s3c2410.o
diff --git a/drivers/clk/samsung/clk-exynos-arm64.c b/drivers/clk/samsung/clk-exynos-arm64.c
new file mode 100644
index 000000000000..b921b9a1134a
--- /dev/null
+++ b/drivers/clk/samsung/clk-exynos-arm64.c
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 Linaro Ltd.
+ * Copyright (C) 2021 Dávid Virág <[email protected]>
+ * Author: Sam Protsenko <[email protected]>
+ * Author: Dávid Virág <[email protected]>
+ *
+ * This file contains shared functions used by some arm64 Exynos SoCs,
+ * such as Exynos7885 or Exynos850 to register and init CMUs.
+ */
+#include <linux/clk.h>
+#include <linux/of_address.h>
+
+#include "clk-exynos-arm64.h"
+
+/* Gate register bits */
+#define GATE_MANUAL BIT(20)
+#define GATE_ENABLE_HWACG BIT(28)
+
+/* Gate register offsets range */
+#define GATE_OFF_START 0x2000
+#define GATE_OFF_END 0x2fff
+
+/**
+ * exynos_arm64_init_clocks - Set clocks initial configuration
+ * @np: CMU device tree node with "reg" property (CMU addr)
+ * @reg_offs: Register offsets array for clocks to init
+ * @reg_offs_len: Number of register offsets in reg_offs array
+ *
+ * Set manual control mode for all gate clocks.
+ */
+static void __init exynos_arm64_init_clocks(struct device_node *np,
+ const unsigned long *reg_offs, size_t reg_offs_len)
+{
+ void __iomem *reg_base;
+ size_t i;
+
+ reg_base = of_iomap(np, 0);
+ if (!reg_base)
+ panic("%s: failed to map registers\n", __func__);
+
+ for (i = 0; i < reg_offs_len; ++i) {
+ void __iomem *reg = reg_base + reg_offs[i];
+ u32 val;
+
+ /* Modify only gate clock registers */
+ if (reg_offs[i] < GATE_OFF_START || reg_offs[i] > GATE_OFF_END)
+ continue;
+
+ val = readl(reg);
+ val |= GATE_MANUAL;
+ val &= ~GATE_ENABLE_HWACG;
+ writel(val, reg);
+ }
+
+ iounmap(reg_base);
+}
+
+/**
+ * exynos_arm64_register_cmu - Register specified Exynos CMU domain
+ * @dev: Device object; may be NULL if this function is not being
+ * called from platform driver probe function
+ * @np: CMU device tree node
+ * @cmu: CMU data
+ *
+ * Register specified CMU domain, which includes next steps:
+ *
+ * 1. Enable parent clock of @cmu CMU
+ * 2. Set initial registers configuration for @cmu CMU clocks
+ * 3. Register @cmu CMU clocks using Samsung clock framework API
+ */
+void __init exynos_arm64_register_cmu(struct device *dev,
+ struct device_node *np, const struct samsung_cmu_info *cmu)
+{
+ /* Keep CMU parent clock running (needed for CMU registers access) */
+ if (cmu->clk_name) {
+ struct clk *parent_clk;
+
+ if (dev)
+ parent_clk = clk_get(dev, cmu->clk_name);
+ else
+ parent_clk = of_clk_get_by_name(np, cmu->clk_name);
+
+ if (IS_ERR(parent_clk)) {
+ pr_err("%s: could not find bus clock %s; err = %ld\n",
+ __func__, cmu->clk_name, PTR_ERR(parent_clk));
+ } else {
+ clk_prepare_enable(parent_clk);
+ }
+ }
+
+ exynos_arm64_init_clocks(np, cmu->clk_regs, cmu->nr_clk_regs);
+ samsung_cmu_register_one(np, cmu);
+}
diff --git a/drivers/clk/samsung/clk-exynos-arm64.h b/drivers/clk/samsung/clk-exynos-arm64.h
new file mode 100644
index 000000000000..184ca79ea649
--- /dev/null
+++ b/drivers/clk/samsung/clk-exynos-arm64.h
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 Linaro Ltd.
+ * Copyright (C) 2021 Dávid Virág <[email protected]>
+ * Author: Sam Protsenko <[email protected]>
+ * Author: Dávid Virág <[email protected]>
+ *
+ * This file contains shared functions used by some arm64 Exynos SoCs,
+ * such as Exynos7885 or Exynos850 to register and init CMUs.
+ */
+
+#ifndef __SAMSUNG_CLK_ARM64_H
+#define __SAMSUNG_CLK_ARM64_H
+
+#include "clk.h"
+
+void exynos_arm64_register_cmu(struct device *dev,
+ struct device_node *np, const struct samsung_cmu_info *cmu);
+
+#endif /* __CLK_EXYNOS_ARM64_H */
diff --git a/drivers/clk/samsung/clk-exynos850.c b/drivers/clk/samsung/clk-exynos850.c
index 568ac97c8120..3cc85b64cbff 100644
--- a/drivers/clk/samsung/clk-exynos850.c
+++ b/drivers/clk/samsung/clk-exynos850.c
@@ -6,96 +6,10 @@
* Common Clock Framework support for Exynos850 SoC.
*/

-#include <linux/clk.h>
-#include <linux/clk-provider.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
#include <linux/of_device.h>
-#include <linux/platform_device.h>
-
#include <dt-bindings/clock/exynos850.h>

-#include "clk.h"
-
-/* Gate register bits */
-#define GATE_MANUAL BIT(20)
-#define GATE_ENABLE_HWACG BIT(28)
-
-/* Gate register offsets range */
-#define GATE_OFF_START 0x2000
-#define GATE_OFF_END 0x2fff
-
-/**
- * exynos850_init_clocks - Set clocks initial configuration
- * @np: CMU device tree node with "reg" property (CMU addr)
- * @reg_offs: Register offsets array for clocks to init
- * @reg_offs_len: Number of register offsets in reg_offs array
- *
- * Set manual control mode for all gate clocks.
- */
-static void __init exynos850_init_clocks(struct device_node *np,
- const unsigned long *reg_offs, size_t reg_offs_len)
-{
- void __iomem *reg_base;
- size_t i;
-
- reg_base = of_iomap(np, 0);
- if (!reg_base)
- panic("%s: failed to map registers\n", __func__);
-
- for (i = 0; i < reg_offs_len; ++i) {
- void __iomem *reg = reg_base + reg_offs[i];
- u32 val;
-
- /* Modify only gate clock registers */
- if (reg_offs[i] < GATE_OFF_START || reg_offs[i] > GATE_OFF_END)
- continue;
-
- val = readl(reg);
- val |= GATE_MANUAL;
- val &= ~GATE_ENABLE_HWACG;
- writel(val, reg);
- }
-
- iounmap(reg_base);
-}
-
-/**
- * exynos850_register_cmu - Register specified Exynos850 CMU domain
- * @dev: Device object; may be NULL if this function is not being
- * called from platform driver probe function
- * @np: CMU device tree node
- * @cmu: CMU data
- *
- * Register specified CMU domain, which includes next steps:
- *
- * 1. Enable parent clock of @cmu CMU
- * 2. Set initial registers configuration for @cmu CMU clocks
- * 3. Register @cmu CMU clocks using Samsung clock framework API
- */
-static void __init exynos850_register_cmu(struct device *dev,
- struct device_node *np, const struct samsung_cmu_info *cmu)
-{
- /* Keep CMU parent clock running (needed for CMU registers access) */
- if (cmu->clk_name) {
- struct clk *parent_clk;
-
- if (dev)
- parent_clk = clk_get(dev, cmu->clk_name);
- else
- parent_clk = of_clk_get_by_name(np, cmu->clk_name);
-
- if (IS_ERR(parent_clk)) {
- pr_err("%s: could not find bus clock %s; err = %ld\n",
- __func__, cmu->clk_name, PTR_ERR(parent_clk));
- } else {
- clk_prepare_enable(parent_clk);
- }
- }
-
- exynos850_init_clocks(np, cmu->clk_regs, cmu->nr_clk_regs);
- samsung_cmu_register_one(np, cmu);
-}
+#include "clk-exynos-arm64.h"

/* ---- CMU_TOP ------------------------------------------------------------- */

@@ -404,7 +318,7 @@ static const struct samsung_cmu_info top_cmu_info __initconst = {

static void __init exynos850_cmu_top_init(struct device_node *np)
{
- exynos850_register_cmu(NULL, np, &top_cmu_info);
+ exynos_arm64_register_cmu(NULL, np, &top_cmu_info);
}

/* Register CMU_TOP early, as it's a dependency for other early domains */
@@ -892,7 +806,7 @@ static const struct samsung_cmu_info peri_cmu_info __initconst = {

static void __init exynos850_cmu_peri_init(struct device_node *np)
{
- exynos850_register_cmu(NULL, np, &peri_cmu_info);
+ exynos_arm64_register_cmu(NULL, np, &peri_cmu_info);
}

/* Register CMU_PERI early, as it's needed for MCT timer */
@@ -1069,7 +983,7 @@ static int __init exynos850_cmu_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;

info = of_device_get_match_data(dev);
- exynos850_register_cmu(dev, dev->of_node, info);
+ exynos_arm64_register_cmu(dev, dev->of_node, info);

return 0;
}
--
2.34.1


2021-12-05 22:12:47

by David Virag

[permalink] [raw]
Subject: [PATCH v2 5/7] clk: samsung: clk-pll: Add support for pll1417x

pll1417x is used in Exynos7885 SoC for top-level integer PLLs.
It is similar enough to pll0822x that practically the same code can
handle both. The difference that's to be noted is that when defining a
pl1417x PLL, the "con" parameter of the PLL macro should be set to the
CON1 register instead of CON3, like this:

PLL(pll_1417x, CLK_FOUT_SHARED0_PLL, "fout_shared0_pll", "oscclk",
PLL_LOCKTIME_PLL_SHARED0, PLL_CON0_PLL_SHARED0,
NULL),

Signed-off-by: David Virag <[email protected]>
---
Changes in v2:
- Nothing

drivers/clk/samsung/clk-pll.c | 1 +
drivers/clk/samsung/clk-pll.h | 1 +
2 files changed, 2 insertions(+)

diff --git a/drivers/clk/samsung/clk-pll.c b/drivers/clk/samsung/clk-pll.c
index 83d1b03647db..70cdc87f714e 100644
--- a/drivers/clk/samsung/clk-pll.c
+++ b/drivers/clk/samsung/clk-pll.c
@@ -1476,6 +1476,7 @@ static void __init _samsung_clk_register_pll(struct samsung_clk_provider *ctx,
else
init.ops = &samsung_pll35xx_clk_ops;
break;
+ case pll_1417x:
case pll_0822x:
pll->enable_offs = PLL0822X_ENABLE_SHIFT;
pll->lock_offs = PLL0822X_LOCK_STAT_SHIFT;
diff --git a/drivers/clk/samsung/clk-pll.h b/drivers/clk/samsung/clk-pll.h
index a739f2b7ae80..c83a20195f6d 100644
--- a/drivers/clk/samsung/clk-pll.h
+++ b/drivers/clk/samsung/clk-pll.h
@@ -32,6 +32,7 @@ enum samsung_pll_type {
pll_2550xx,
pll_2650x,
pll_2650xx,
+ pll_1417x,
pll_1450x,
pll_1451x,
pll_1452x,
--
2.34.1


2021-12-05 22:12:51

by David Virag

[permalink] [raw]
Subject: [PATCH v2 6/7] clk: samsung: Add initial Exynos7885 clock driver

This is an initial implementation adding basic clocks, such as UART,
USI, I2C, WDT, ect. and their parent clocks. It is heavily based on the
Exynos850 clock driver at 'drivers/clk/samsung/clk-exynos850.c' which
was made by Sam Protsenko, thus the copyright and author lines were
kept.

Bus clocks are enabled by default as well to avoid hangs while trying to
access CMU registers.

Only the parts of CMU_TOP needed for CMU_CORE and CMU_PERI, a bit of
CMU_CORE, and most of CMU_PERI is implemented as of now.

Signed-off-by: David Virag <[email protected]>
---
Changes in v2:
- Use shared code between Exynos850 and 7885 clock drivers
- As the code that was from the Exynos850 clock driver was moved to
clk-exynos-arm64.c and what remains is mostly SoC specific data,
move the Linaro copyright and Sam Protsenko author lines there.

drivers/clk/samsung/Makefile | 1 +
drivers/clk/samsung/clk-exynos7885.c | 593 +++++++++++++++++++++++++++
2 files changed, 594 insertions(+)
create mode 100644 drivers/clk/samsung/clk-exynos7885.c

diff --git a/drivers/clk/samsung/Makefile b/drivers/clk/samsung/Makefile
index 901e6333c5f0..0df74916a895 100644
--- a/drivers/clk/samsung/Makefile
+++ b/drivers/clk/samsung/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_EXYNOS_AUDSS_CLK_CON) += clk-exynos-audss.o
obj-$(CONFIG_EXYNOS_CLKOUT) += clk-exynos-clkout.o
obj-$(CONFIG_EXYNOS_ARM64_COMMON_CLK) += clk-exynos-arm64.o
obj-$(CONFIG_EXYNOS_ARM64_COMMON_CLK) += clk-exynos7.o
+obj-$(CONFIG_EXYNOS_ARM64_COMMON_CLK) += clk-exynos7885.o
obj-$(CONFIG_EXYNOS_ARM64_COMMON_CLK) += clk-exynos850.o
obj-$(CONFIG_S3C2410_COMMON_CLK)+= clk-s3c2410.o
obj-$(CONFIG_S3C2410_COMMON_DCLK)+= clk-s3c2410-dclk.o
diff --git a/drivers/clk/samsung/clk-exynos7885.c b/drivers/clk/samsung/clk-exynos7885.c
new file mode 100644
index 000000000000..0b3a28800e76
--- /dev/null
+++ b/drivers/clk/samsung/clk-exynos7885.c
@@ -0,0 +1,591 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 Dávid Virág <[email protected]>
+ * Author: Dávid Virág <[email protected]>
+ *
+ * Common Clock Framework support for Exynos7885 SoC.
+ */
+
+#include <linux/of_device.h>
+#include <dt-bindings/clock/exynos7885.h>
+
+#include "clk-exynos-arm64.h"
+
+/* ---- CMU_TOP ------------------------------------------------------------- */
+
+/* Register Offset definitions for CMU_TOP (0x12060000) */
+#define PLL_LOCKTIME_PLL_SHARED0 0x0000
+#define PLL_LOCKTIME_PLL_SHARED1 0x0004
+#define PLL_CON0_PLL_SHARED0 0x0100
+#define PLL_CON0_PLL_SHARED1 0x0120
+#define CLK_CON_MUX_MUX_CLKCMU_CORE_BUS 0x1014
+#define CLK_CON_MUX_MUX_CLKCMU_CORE_CCI 0x1018
+#define CLK_CON_MUX_MUX_CLKCMU_CORE_G3D 0x101c
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_BUS 0x1058
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_SPI0 0x105c
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_SPI1 0x1060
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_UART0 0x1064
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_UART1 0x1068
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_UART2 0x106c
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_USI0 0x1070
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_USI1 0x1074
+#define CLK_CON_MUX_MUX_CLKCMU_PERI_USI2 0x1078
+#define CLK_CON_DIV_CLKCMU_CORE_BUS 0x181c
+#define CLK_CON_DIV_CLKCMU_CORE_CCI 0x1820
+#define CLK_CON_DIV_CLKCMU_CORE_G3D 0x1824
+#define CLK_CON_DIV_CLKCMU_PERI_BUS 0x1874
+#define CLK_CON_DIV_CLKCMU_PERI_SPI0 0x1878
+#define CLK_CON_DIV_CLKCMU_PERI_SPI1 0x187c
+#define CLK_CON_DIV_CLKCMU_PERI_UART0 0x1880
+#define CLK_CON_DIV_CLKCMU_PERI_UART1 0x1884
+#define CLK_CON_DIV_CLKCMU_PERI_UART2 0x1888
+#define CLK_CON_DIV_CLKCMU_PERI_USI0 0x188c
+#define CLK_CON_DIV_CLKCMU_PERI_USI1 0x1890
+#define CLK_CON_DIV_CLKCMU_PERI_USI2 0x1894
+#define CLK_CON_DIV_PLL_SHARED0_DIV2 0x189c
+#define CLK_CON_DIV_PLL_SHARED0_DIV3 0x18a0
+#define CLK_CON_DIV_PLL_SHARED0_DIV4 0x18a4
+#define CLK_CON_DIV_PLL_SHARED0_DIV5 0x18a8
+#define CLK_CON_DIV_PLL_SHARED1_DIV2 0x18ac
+#define CLK_CON_DIV_PLL_SHARED1_DIV3 0x18b0
+#define CLK_CON_DIV_PLL_SHARED1_DIV4 0x18b4
+#define CLK_CON_GAT_GATE_CLKCMUC_PERI_UART1 0x2004
+#define CLK_CON_GAT_GATE_CLKCMU_CORE_BUS 0x201c
+#define CLK_CON_GAT_GATE_CLKCMU_CORE_CCI 0x2020
+#define CLK_CON_GAT_GATE_CLKCMU_CORE_G3D 0x2024
+#define CLK_CON_GAT_GATE_CLKCMU_PERI_BUS 0x207c
+#define CLK_CON_GAT_GATE_CLKCMU_PERI_SPI0 0x2080
+#define CLK_CON_GAT_GATE_CLKCMU_PERI_SPI1 0x2084
+#define CLK_CON_GAT_GATE_CLKCMU_PERI_UART0 0x2088
+#define CLK_CON_GAT_GATE_CLKCMU_PERI_UART2 0x208c
+#define CLK_CON_GAT_GATE_CLKCMU_PERI_USI0 0x2090
+#define CLK_CON_GAT_GATE_CLKCMU_PERI_USI1 0x2094
+#define CLK_CON_GAT_GATE_CLKCMU_PERI_USI2 0x2098
+
+static const unsigned long top_clk_regs[] __initconst = {
+ PLL_LOCKTIME_PLL_SHARED0,
+ PLL_LOCKTIME_PLL_SHARED1,
+ PLL_CON0_PLL_SHARED0,
+ PLL_CON0_PLL_SHARED1,
+ CLK_CON_MUX_MUX_CLKCMU_CORE_BUS,
+ CLK_CON_MUX_MUX_CLKCMU_CORE_CCI,
+ CLK_CON_MUX_MUX_CLKCMU_CORE_G3D,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_BUS,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_SPI0,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_SPI1,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_UART0,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_UART1,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_UART2,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_USI0,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_USI1,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_USI2,
+ CLK_CON_DIV_CLKCMU_CORE_BUS,
+ CLK_CON_DIV_CLKCMU_CORE_CCI,
+ CLK_CON_DIV_CLKCMU_CORE_G3D,
+ CLK_CON_DIV_CLKCMU_PERI_BUS,
+ CLK_CON_DIV_CLKCMU_PERI_SPI0,
+ CLK_CON_DIV_CLKCMU_PERI_SPI1,
+ CLK_CON_DIV_CLKCMU_PERI_UART0,
+ CLK_CON_DIV_CLKCMU_PERI_UART1,
+ CLK_CON_DIV_CLKCMU_PERI_UART2,
+ CLK_CON_DIV_CLKCMU_PERI_USI0,
+ CLK_CON_DIV_CLKCMU_PERI_USI1,
+ CLK_CON_DIV_CLKCMU_PERI_USI2,
+ CLK_CON_DIV_PLL_SHARED0_DIV2,
+ CLK_CON_DIV_PLL_SHARED0_DIV3,
+ CLK_CON_DIV_PLL_SHARED0_DIV4,
+ CLK_CON_DIV_PLL_SHARED0_DIV5,
+ CLK_CON_DIV_PLL_SHARED1_DIV2,
+ CLK_CON_DIV_PLL_SHARED1_DIV3,
+ CLK_CON_DIV_PLL_SHARED1_DIV4,
+ CLK_CON_GAT_GATE_CLKCMUC_PERI_UART1,
+ CLK_CON_GAT_GATE_CLKCMU_CORE_BUS,
+ CLK_CON_GAT_GATE_CLKCMU_CORE_CCI,
+ CLK_CON_GAT_GATE_CLKCMU_CORE_G3D,
+ CLK_CON_GAT_GATE_CLKCMU_PERI_BUS,
+ CLK_CON_GAT_GATE_CLKCMU_PERI_SPI0,
+ CLK_CON_GAT_GATE_CLKCMU_PERI_SPI1,
+ CLK_CON_GAT_GATE_CLKCMU_PERI_UART0,
+ CLK_CON_GAT_GATE_CLKCMU_PERI_UART2,
+ CLK_CON_GAT_GATE_CLKCMU_PERI_USI0,
+ CLK_CON_GAT_GATE_CLKCMU_PERI_USI1,
+ CLK_CON_GAT_GATE_CLKCMU_PERI_USI2,
+};
+
+static const struct samsung_pll_clock top_pll_clks[] __initconst = {
+ PLL(pll_1417x, CLK_FOUT_SHARED0_PLL, "fout_shared0_pll", "oscclk",
+ PLL_LOCKTIME_PLL_SHARED0, PLL_CON0_PLL_SHARED0,
+ NULL),
+ PLL(pll_1417x, CLK_FOUT_SHARED1_PLL, "fout_shared1_pll", "oscclk",
+ PLL_LOCKTIME_PLL_SHARED1, PLL_CON0_PLL_SHARED1,
+ NULL),
+};
+
+/* List of parent clocks for Muxes in CMU_TOP: for CMU_CORE */
+PNAME(mout_core_bus_p) = { "dout_shared0_div2", "dout_shared1_div2",
+ "dout_shared0_div3", "dout_shared0_div3" };
+PNAME(mout_core_cci_p) = { "dout_shared0_div2", "dout_shared1_div2",
+ "dout_shared0_div3", "dout_shared0_div3" };
+PNAME(mout_core_g3d_p) = { "dout_shared0_div2", "dout_shared1_div2",
+ "dout_shared0_div3", "dout_shared0_div3" };
+
+/* List of parent clocks for Muxes in CMU_TOP: for CMU_PERI */
+PNAME(mout_peri_bus_p) = { "dout_shared0_div4", "dout_shared1_div4" };
+PNAME(mout_peri_spi0_p) = { "oscclk", "dout_shared0_div4" };
+PNAME(mout_peri_spi1_p) = { "oscclk", "dout_shared0_div4" };
+PNAME(mout_peri_uart0_p) = { "oscclk", "dout_shared0_div4" };
+PNAME(mout_peri_uart1_p) = { "oscclk", "dout_shared0_div4" };
+PNAME(mout_peri_uart2_p) = { "oscclk", "dout_shared0_div4" };
+PNAME(mout_peri_usi0_p) = { "oscclk", "dout_shared0_div4" };
+PNAME(mout_peri_usi1_p) = { "oscclk", "dout_shared0_div4" };
+PNAME(mout_peri_usi2_p) = { "oscclk", "dout_shared0_div4" };
+
+static const struct samsung_mux_clock top_mux_clks[] __initconst = {
+ /* CORE */
+ MUX(CLK_MOUT_CORE_BUS, "mout_core_bus", mout_core_bus_p,
+ CLK_CON_MUX_MUX_CLKCMU_CORE_BUS, 0, 2),
+ MUX(CLK_MOUT_CORE_CCI, "mout_core_cci", mout_core_cci_p,
+ CLK_CON_MUX_MUX_CLKCMU_CORE_CCI, 0, 2),
+ MUX(CLK_MOUT_CORE_G3D, "mout_core_g3d", mout_core_g3d_p,
+ CLK_CON_MUX_MUX_CLKCMU_CORE_G3D, 0, 2),
+
+ /* PERI */
+ MUX(CLK_MOUT_PERI_BUS, "mout_peri_bus", mout_peri_bus_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_BUS, 0, 1),
+ MUX(CLK_MOUT_PERI_SPI0, "mout_peri_spi0", mout_peri_spi0_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_SPI0, 0, 1),
+ MUX(CLK_MOUT_PERI_SPI1, "mout_peri_spi1", mout_peri_spi1_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_SPI1, 0, 1),
+ MUX(CLK_MOUT_PERI_UART0, "mout_peri_uart0", mout_peri_uart0_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_UART0, 0, 1),
+ MUX(CLK_MOUT_PERI_UART1, "mout_peri_uart1", mout_peri_uart1_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_UART1, 0, 1),
+ MUX(CLK_MOUT_PERI_UART2, "mout_peri_uart2", mout_peri_uart2_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_UART2, 0, 1),
+ MUX(CLK_MOUT_PERI_USI0, "mout_peri_usi0", mout_peri_usi0_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_USI0, 0, 1),
+ MUX(CLK_MOUT_PERI_USI1, "mout_peri_usi1", mout_peri_usi1_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_USI1, 0, 1),
+ MUX(CLK_MOUT_PERI_USI2, "mout_peri_usi2", mout_peri_usi2_p,
+ CLK_CON_MUX_MUX_CLKCMU_PERI_USI2, 0, 1),
+};
+
+static const struct samsung_div_clock top_div_clks[] __initconst = {
+ /* TOP */
+ DIV(CLK_DOUT_SHARED0_DIV2, "dout_shared0_div2", "fout_shared0_pll",
+ CLK_CON_DIV_PLL_SHARED0_DIV2, 0, 1),
+ DIV(CLK_DOUT_SHARED0_DIV3, "dout_shared0_div3", "fout_shared0_pll",
+ CLK_CON_DIV_PLL_SHARED0_DIV3, 0, 2),
+ DIV(CLK_DOUT_SHARED0_DIV4, "dout_shared0_div4", "fout_shared0_pll",
+ CLK_CON_DIV_PLL_SHARED0_DIV4, 0, 1),
+ DIV(CLK_DOUT_SHARED0_DIV5, "dout_shared0_div5", "fout_shared0_pll",
+ CLK_CON_DIV_PLL_SHARED0_DIV5, 0, 3),
+ DIV(CLK_DOUT_SHARED1_DIV2, "dout_shared1_div2", "fout_shared1_pll",
+ CLK_CON_DIV_PLL_SHARED1_DIV2, 0, 1),
+ DIV(CLK_DOUT_SHARED1_DIV3, "dout_shared1_div3", "fout_shared1_pll",
+ CLK_CON_DIV_PLL_SHARED1_DIV3, 0, 2),
+ DIV(CLK_DOUT_SHARED1_DIV4, "dout_shared1_div4", "fout_shared1_pll",
+ CLK_CON_DIV_PLL_SHARED1_DIV4, 0, 1),
+
+ /* CORE */
+ DIV(CLK_DOUT_CORE_BUS, "dout_core_bus", "gout_core_bus",
+ CLK_CON_DIV_CLKCMU_CORE_BUS, 0, 3),
+ DIV(CLK_DOUT_CORE_CCI, "dout_core_cci", "gout_core_cci",
+ CLK_CON_DIV_CLKCMU_CORE_CCI, 0, 3),
+ DIV(CLK_DOUT_CORE_G3D, "dout_core_g3d", "gout_core_g3d",
+ CLK_CON_DIV_CLKCMU_CORE_G3D, 0, 3),
+
+ /* PERI */
+ DIV(CLK_DOUT_PERI_BUS, "dout_peri_bus", "gout_peri_bus",
+ CLK_CON_DIV_CLKCMU_PERI_BUS, 0, 4),
+ DIV(CLK_DOUT_PERI_SPI0, "dout_peri_spi0", "gout_peri_spi0",
+ CLK_CON_DIV_CLKCMU_PERI_SPI0, 0, 6),
+ DIV(CLK_DOUT_PERI_SPI1, "dout_peri_spi1", "gout_peri_spi1",
+ CLK_CON_DIV_CLKCMU_PERI_SPI1, 0, 6),
+ DIV(CLK_DOUT_PERI_UART0, "dout_peri_uart0", "gout_peri_uart0",
+ CLK_CON_DIV_CLKCMU_PERI_UART0, 0, 4),
+ DIV(CLK_DOUT_PERI_UART1, "dout_peri_uart1", "gout_peri_uart1",
+ CLK_CON_DIV_CLKCMU_PERI_UART1, 0, 4),
+ DIV(CLK_DOUT_PERI_UART2, "dout_peri_uart2", "gout_peri_uart2",
+ CLK_CON_DIV_CLKCMU_PERI_UART2, 0, 4),
+ DIV(CLK_DOUT_PERI_USI0, "dout_peri_usi0", "gout_peri_usi0",
+ CLK_CON_DIV_CLKCMU_PERI_USI0, 0, 4),
+ DIV(CLK_DOUT_PERI_USI1, "dout_peri_usi1", "gout_peri_usi1",
+ CLK_CON_DIV_CLKCMU_PERI_USI1, 0, 4),
+ DIV(CLK_DOUT_PERI_USI2, "dout_peri_usi2", "gout_peri_usi2",
+ CLK_CON_DIV_CLKCMU_PERI_USI2, 0, 4),
+};
+
+static const struct samsung_gate_clock top_gate_clks[] __initconst = {
+ /* CORE */
+ GATE(CLK_GOUT_CORE_BUS, "gout_core_bus", "mout_core_bus",
+ CLK_CON_GAT_GATE_CLKCMU_CORE_BUS, 21, 0, 0),
+ GATE(CLK_GOUT_CORE_CCI, "gout_core_cci", "mout_core_cci",
+ CLK_CON_GAT_GATE_CLKCMU_CORE_CCI, 21, 0, 0),
+ GATE(CLK_GOUT_CORE_G3D, "gout_core_g3d", "mout_core_g3d",
+ CLK_CON_GAT_GATE_CLKCMU_CORE_G3D, 21, 0, 0),
+
+ /* PERI */
+ GATE(CLK_GOUT_PERI_BUS, "gout_peri_bus", "mout_peri_bus",
+ CLK_CON_GAT_GATE_CLKCMU_PERI_BUS, 21, 0, 0),
+ GATE(CLK_GOUT_PERI_SPI0, "gout_peri_spi0", "mout_peri_spi0",
+ CLK_CON_GAT_GATE_CLKCMU_PERI_SPI0, 21, 0, 0),
+ GATE(CLK_GOUT_PERI_SPI1, "gout_peri_spi1", "mout_peri_spi1",
+ CLK_CON_GAT_GATE_CLKCMU_PERI_SPI1, 21, 0, 0),
+ GATE(CLK_GOUT_PERI_UART0, "gout_peri_uart0", "mout_peri_uart0",
+ CLK_CON_GAT_GATE_CLKCMU_PERI_UART0, 21, 0, 0),
+ GATE(CLK_GOUT_PERI_UART1, "gout_peri_uart1", "mout_peri_uart1",
+ CLK_CON_GAT_GATE_CLKCMUC_PERI_UART1, 21, 0, 0),
+ GATE(CLK_GOUT_PERI_UART2, "gout_peri_uart2", "mout_peri_uart2",
+ CLK_CON_GAT_GATE_CLKCMU_PERI_UART2, 21, 0, 0),
+ GATE(CLK_GOUT_PERI_USI0, "gout_peri_usi0", "mout_peri_usi0",
+ CLK_CON_GAT_GATE_CLKCMU_PERI_USI0, 21, 0, 0),
+ GATE(CLK_GOUT_PERI_USI1, "gout_peri_usi1", "mout_peri_usi1",
+ CLK_CON_GAT_GATE_CLKCMU_PERI_USI1, 21, 0, 0),
+ GATE(CLK_GOUT_PERI_USI2, "gout_peri_usi2", "mout_peri_usi2",
+ CLK_CON_GAT_GATE_CLKCMU_PERI_USI2, 21, 0, 0),
+};
+
+static const struct samsung_cmu_info top_cmu_info __initconst = {
+ .pll_clks = top_pll_clks,
+ .nr_pll_clks = ARRAY_SIZE(top_pll_clks),
+ .mux_clks = top_mux_clks,
+ .nr_mux_clks = ARRAY_SIZE(top_mux_clks),
+ .div_clks = top_div_clks,
+ .nr_div_clks = ARRAY_SIZE(top_div_clks),
+ .gate_clks = top_gate_clks,
+ .nr_gate_clks = ARRAY_SIZE(top_gate_clks),
+ .nr_clk_ids = TOP_NR_CLK,
+ .clk_regs = top_clk_regs,
+ .nr_clk_regs = ARRAY_SIZE(top_clk_regs),
+};
+
+static void __init exynos7885_cmu_top_init(struct device_node *np)
+{
+ exynos_arm64_register_cmu(NULL, np, &top_cmu_info);
+}
+
+/* Register CMU_TOP early, as it's a dependency for other early domains */
+CLK_OF_DECLARE(exynos7885_cmu_top, "samsung,exynos7885-cmu-top",
+ exynos7885_cmu_top_init);
+
+/* ---- CMU_PERI ------------------------------------------------------------ */
+
+/* Register Offset definitions for CMU_PERI (0x10010000) */
+#define PLL_CON0_MUX_CLKCMU_PERI_BUS_USER 0x0100
+#define PLL_CON0_MUX_CLKCMU_PERI_SPI0_USER 0x0120
+#define PLL_CON0_MUX_CLKCMU_PERI_SPI1_USER 0x0140
+#define PLL_CON0_MUX_CLKCMU_PERI_UART0_USER 0x0160
+#define PLL_CON0_MUX_CLKCMU_PERI_UART1_USER 0x0180
+#define PLL_CON0_MUX_CLKCMU_PERI_UART2_USER 0x01a0
+#define PLL_CON0_MUX_CLKCMU_PERI_USI0_USER 0x01c0
+#define PLL_CON0_MUX_CLKCMU_PERI_USI1_USER 0x01e0
+#define PLL_CON0_MUX_CLKCMU_PERI_USI2_USER 0x0200
+#define CLK_CON_GAT_GOUT_PERI_GPIO_TOP_PCLK 0x2024
+#define CLK_CON_GAT_GOUT_PERI_HSI2C_0_PCLK 0x2028
+#define CLK_CON_GAT_GOUT_PERI_HSI2C_1_PCLK 0x202c
+#define CLK_CON_GAT_GOUT_PERI_HSI2C_2_PCLK 0x2030
+#define CLK_CON_GAT_GOUT_PERI_HSI2C_3_PCLK 0x2034
+#define CLK_CON_GAT_GOUT_PERI_I2C_0_PCLK 0x2038
+#define CLK_CON_GAT_GOUT_PERI_I2C_1_PCLK 0x203c
+#define CLK_CON_GAT_GOUT_PERI_I2C_2_PCLK 0x2040
+#define CLK_CON_GAT_GOUT_PERI_I2C_3_PCLK 0x2044
+#define CLK_CON_GAT_GOUT_PERI_I2C_4_PCLK 0x2048
+#define CLK_CON_GAT_GOUT_PERI_I2C_5_PCLK 0x204c
+#define CLK_CON_GAT_GOUT_PERI_I2C_6_PCLK 0x2050
+#define CLK_CON_GAT_GOUT_PERI_I2C_7_PCLK 0x2054
+#define CLK_CON_GAT_GOUT_PERI_PWM_MOTOR_PCLK 0x2058
+#define CLK_CON_GAT_GOUT_PERI_SPI_0_PCLK 0x205c
+#define CLK_CON_GAT_GOUT_PERI_SPI_0_EXT_CLK 0x2060
+#define CLK_CON_GAT_GOUT_PERI_SPI_1_PCLK 0x2064
+#define CLK_CON_GAT_GOUT_PERI_SPI_1_EXT_CLK 0x2068
+#define CLK_CON_GAT_GOUT_PERI_UART_0_EXT_UCLK 0x206c
+#define CLK_CON_GAT_GOUT_PERI_UART_0_PCLK 0x2070
+#define CLK_CON_GAT_GOUT_PERI_UART_1_EXT_UCLK 0x2074
+#define CLK_CON_GAT_GOUT_PERI_UART_1_PCLK 0x2078
+#define CLK_CON_GAT_GOUT_PERI_UART_2_EXT_UCLK 0x207c
+#define CLK_CON_GAT_GOUT_PERI_UART_2_PCLK 0x2080
+#define CLK_CON_GAT_GOUT_PERI_USI0_PCLK 0x2084
+#define CLK_CON_GAT_GOUT_PERI_USI0_SCLK 0x2088
+#define CLK_CON_GAT_GOUT_PERI_USI1_PCLK 0x208c
+#define CLK_CON_GAT_GOUT_PERI_USI1_SCLK 0x2090
+#define CLK_CON_GAT_GOUT_PERI_USI2_PCLK 0x2094
+#define CLK_CON_GAT_GOUT_PERI_USI2_SCLK 0x2098
+#define CLK_CON_GAT_GOUT_PERI_MCT_PCLK 0x20a0
+#define CLK_CON_GAT_GOUT_PERI_SYSREG_PERI_PCLK 0x20b0
+#define CLK_CON_GAT_GOUT_PERI_WDT_CLUSTER0_PCLK 0x20b4
+#define CLK_CON_GAT_GOUT_PERI_WDT_CLUSTER1_PCLK 0x20b8
+
+static const unsigned long peri_clk_regs[] __initconst = {
+ PLL_CON0_MUX_CLKCMU_PERI_BUS_USER,
+ PLL_CON0_MUX_CLKCMU_PERI_SPI0_USER,
+ PLL_CON0_MUX_CLKCMU_PERI_SPI1_USER,
+ PLL_CON0_MUX_CLKCMU_PERI_UART0_USER,
+ PLL_CON0_MUX_CLKCMU_PERI_UART1_USER,
+ PLL_CON0_MUX_CLKCMU_PERI_UART2_USER,
+ PLL_CON0_MUX_CLKCMU_PERI_USI0_USER,
+ PLL_CON0_MUX_CLKCMU_PERI_USI1_USER,
+ PLL_CON0_MUX_CLKCMU_PERI_USI2_USER,
+ CLK_CON_GAT_GOUT_PERI_GPIO_TOP_PCLK,
+ CLK_CON_GAT_GOUT_PERI_HSI2C_0_PCLK,
+ CLK_CON_GAT_GOUT_PERI_HSI2C_1_PCLK,
+ CLK_CON_GAT_GOUT_PERI_HSI2C_2_PCLK,
+ CLK_CON_GAT_GOUT_PERI_HSI2C_3_PCLK,
+ CLK_CON_GAT_GOUT_PERI_I2C_0_PCLK,
+ CLK_CON_GAT_GOUT_PERI_I2C_1_PCLK,
+ CLK_CON_GAT_GOUT_PERI_I2C_2_PCLK,
+ CLK_CON_GAT_GOUT_PERI_I2C_3_PCLK,
+ CLK_CON_GAT_GOUT_PERI_I2C_4_PCLK,
+ CLK_CON_GAT_GOUT_PERI_I2C_5_PCLK,
+ CLK_CON_GAT_GOUT_PERI_I2C_6_PCLK,
+ CLK_CON_GAT_GOUT_PERI_I2C_7_PCLK,
+ CLK_CON_GAT_GOUT_PERI_PWM_MOTOR_PCLK,
+ CLK_CON_GAT_GOUT_PERI_SPI_0_PCLK,
+ CLK_CON_GAT_GOUT_PERI_SPI_0_EXT_CLK,
+ CLK_CON_GAT_GOUT_PERI_SPI_1_PCLK,
+ CLK_CON_GAT_GOUT_PERI_SPI_1_EXT_CLK,
+ CLK_CON_GAT_GOUT_PERI_UART_0_EXT_UCLK,
+ CLK_CON_GAT_GOUT_PERI_UART_0_PCLK,
+ CLK_CON_GAT_GOUT_PERI_UART_1_EXT_UCLK,
+ CLK_CON_GAT_GOUT_PERI_UART_1_PCLK,
+ CLK_CON_GAT_GOUT_PERI_UART_2_EXT_UCLK,
+ CLK_CON_GAT_GOUT_PERI_UART_2_PCLK,
+ CLK_CON_GAT_GOUT_PERI_USI0_PCLK,
+ CLK_CON_GAT_GOUT_PERI_USI0_SCLK,
+ CLK_CON_GAT_GOUT_PERI_USI1_PCLK,
+ CLK_CON_GAT_GOUT_PERI_USI1_SCLK,
+ CLK_CON_GAT_GOUT_PERI_USI2_PCLK,
+ CLK_CON_GAT_GOUT_PERI_USI2_SCLK,
+ CLK_CON_GAT_GOUT_PERI_MCT_PCLK,
+ CLK_CON_GAT_GOUT_PERI_SYSREG_PERI_PCLK,
+ CLK_CON_GAT_GOUT_PERI_WDT_CLUSTER0_PCLK,
+ CLK_CON_GAT_GOUT_PERI_WDT_CLUSTER1_PCLK,
+};
+
+/* List of parent clocks for Muxes in CMU_PERI */
+PNAME(mout_peri_bus_user_p) = { "oscclk", "dout_peri_bus" };
+PNAME(mout_peri_spi0_user_p) = { "oscclk", "dout_peri_spi0" };
+PNAME(mout_peri_spi1_user_p) = { "oscclk", "dout_peri_spi1" };
+PNAME(mout_peri_uart0_user_p) = { "oscclk", "dout_peri_uart0" };
+PNAME(mout_peri_uart1_user_p) = { "oscclk", "dout_peri_uart1" };
+PNAME(mout_peri_uart2_user_p) = { "oscclk", "dout_peri_uart2" };
+PNAME(mout_peri_usi0_user_p) = { "oscclk", "dout_peri_usi0" };
+PNAME(mout_peri_usi1_user_p) = { "oscclk", "dout_peri_usi1" };
+PNAME(mout_peri_usi2_user_p) = { "oscclk", "dout_peri_usi2" };
+
+static const struct samsung_mux_clock peri_mux_clks[] __initconst = {
+ MUX(CLK_MOUT_PERI_BUS_USER, "mout_peri_bus_user", mout_peri_bus_user_p,
+ PLL_CON0_MUX_CLKCMU_PERI_BUS_USER, 4, 1),
+ MUX(CLK_MOUT_PERI_SPI0_USER, "mout_peri_spi0_user", mout_peri_spi0_user_p,
+ PLL_CON0_MUX_CLKCMU_PERI_SPI0_USER, 4, 1),
+ MUX(CLK_MOUT_PERI_SPI1_USER, "mout_peri_spi1_user", mout_peri_spi1_user_p,
+ PLL_CON0_MUX_CLKCMU_PERI_SPI1_USER, 4, 1),
+ MUX(CLK_MOUT_PERI_UART0_USER, "mout_peri_uart0_user",
+ mout_peri_uart0_user_p, PLL_CON0_MUX_CLKCMU_PERI_UART0_USER, 4, 1),
+ MUX(CLK_MOUT_PERI_UART1_USER, "mout_peri_uart1_user",
+ mout_peri_uart1_user_p, PLL_CON0_MUX_CLKCMU_PERI_UART1_USER, 4, 1),
+ MUX(CLK_MOUT_PERI_UART2_USER, "mout_peri_uart2_user",
+ mout_peri_uart2_user_p, PLL_CON0_MUX_CLKCMU_PERI_UART2_USER, 4, 1),
+ MUX(CLK_MOUT_PERI_USI0_USER, "mout_peri_usi0_user",
+ mout_peri_usi0_user_p, PLL_CON0_MUX_CLKCMU_PERI_USI0_USER, 4, 1),
+ MUX(CLK_MOUT_PERI_USI1_USER, "mout_peri_usi1_user",
+ mout_peri_usi1_user_p, PLL_CON0_MUX_CLKCMU_PERI_USI1_USER, 4, 1),
+ MUX(CLK_MOUT_PERI_USI2_USER, "mout_peri_usi2_user",
+ mout_peri_usi2_user_p, PLL_CON0_MUX_CLKCMU_PERI_USI2_USER, 4, 1),
+};
+
+static const struct samsung_gate_clock peri_gate_clks[] __initconst = {
+ /* TODO: Should be enabled in GPIO driver (or made CLK_IS_CRITICAL) */
+ GATE(CLK_GOUT_GPIO_TOP_PCLK, "gout_gpio_top_pclk",
+ "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_GPIO_TOP_PCLK, 21, CLK_IGNORE_UNUSED, 0),
+ GATE(CLK_GOUT_HSI2C0_PCLK, "gout_hsi2c0_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_HSI2C_0_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_HSI2C1_PCLK, "gout_hsi2c1_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_HSI2C_1_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_HSI2C2_PCLK, "gout_hsi2c2_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_HSI2C_2_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_HSI2C3_PCLK, "gout_hsi2c3_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_HSI2C_3_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_I2C0_PCLK, "gout_i2c0_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_I2C_0_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_I2C1_PCLK, "gout_i2c1_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_I2C_1_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_I2C2_PCLK, "gout_i2c2_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_I2C_2_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_I2C3_PCLK, "gout_i2c3_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_I2C_3_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_I2C4_PCLK, "gout_i2c4_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_I2C_4_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_I2C5_PCLK, "gout_i2c5_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_I2C_5_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_I2C6_PCLK, "gout_i2c6_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_I2C_6_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_I2C7_PCLK, "gout_i2c7_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_I2C_7_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_PWM_MOTOR_PCLK, "gout_pwm_motor_pclk",
+ "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_PWM_MOTOR_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_SPI0_PCLK, "gout_spi0_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_SPI_0_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_SPI0_EXT_CLK, "gout_spi0_ipclk", "mout_peri_spi0_user",
+ CLK_CON_GAT_GOUT_PERI_SPI_0_EXT_CLK, 21, 0, 0),
+ GATE(CLK_GOUT_SPI1_PCLK, "gout_spi1_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_SPI_1_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_SPI1_EXT_CLK, "gout_spi1_ipclk", "mout_peri_spi1_user",
+ CLK_CON_GAT_GOUT_PERI_SPI_1_EXT_CLK, 21, 0, 0),
+ GATE(CLK_GOUT_UART0_EXT_UCLK, "gout_uart0_ext_uclk", "mout_peri_uart0_user",
+ CLK_CON_GAT_GOUT_PERI_UART_0_EXT_UCLK, 21, 0, 0),
+ GATE(CLK_GOUT_UART0_PCLK, "gout_uart0_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_UART_0_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_UART1_EXT_UCLK, "gout_uart1_ext_uclk", "mout_peri_uart1_user",
+ CLK_CON_GAT_GOUT_PERI_UART_1_EXT_UCLK, 21, 0, 0),
+ GATE(CLK_GOUT_UART1_PCLK, "gout_uart1_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_UART_1_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_UART2_EXT_UCLK, "gout_uart2_ext_uclk", "mout_peri_uart2_user",
+ CLK_CON_GAT_GOUT_PERI_UART_2_EXT_UCLK, 21, 0, 0),
+ GATE(CLK_GOUT_UART2_PCLK, "gout_uart2_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_UART_2_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_USI0_PCLK, "gout_usi0_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_USI0_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_USI0_SCLK, "gout_usi0_sclk", "mout_peri_usi0_user",
+ CLK_CON_GAT_GOUT_PERI_USI0_SCLK, 21, 0, 0),
+ GATE(CLK_GOUT_USI1_PCLK, "gout_usi1_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_USI1_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_USI1_SCLK, "gout_usi1_sclk", "mout_peri_usi1_user",
+ CLK_CON_GAT_GOUT_PERI_USI1_SCLK, 21, 0, 0),
+ GATE(CLK_GOUT_USI2_PCLK, "gout_usi2_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_USI2_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_USI2_SCLK, "gout_usi2_sclk", "mout_peri_usi2_user",
+ CLK_CON_GAT_GOUT_PERI_USI2_SCLK, 21, 0, 0),
+ GATE(CLK_GOUT_MCT_PCLK, "gout_mct_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_MCT_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_SYSREG_PERI_PCLK, "gout_sysreg_peri_pclk",
+ "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_SYSREG_PERI_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_WDT0_PCLK, "gout_wdt0_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_WDT_CLUSTER0_PCLK, 21, 0, 0),
+ GATE(CLK_GOUT_WDT1_PCLK, "gout_wdt1_pclk", "mout_peri_bus_user",
+ CLK_CON_GAT_GOUT_PERI_WDT_CLUSTER1_PCLK, 21, 0, 0),
+};
+
+static const struct samsung_cmu_info peri_cmu_info __initconst = {
+ .mux_clks = peri_mux_clks,
+ .nr_mux_clks = ARRAY_SIZE(peri_mux_clks),
+ .gate_clks = peri_gate_clks,
+ .nr_gate_clks = ARRAY_SIZE(peri_gate_clks),
+ .nr_clk_ids = PERI_NR_CLK,
+ .clk_regs = peri_clk_regs,
+ .nr_clk_regs = ARRAY_SIZE(peri_clk_regs),
+ .clk_name = "dout_peri_bus",
+};
+
+static void __init exynos7885_cmu_peri_init(struct device_node *np)
+{
+ exynos_arm64_register_cmu(NULL, np, &peri_cmu_info);
+}
+
+/* Register CMU_PERI early, as it's needed for MCT timer */
+CLK_OF_DECLARE(exynos7885_cmu_peri, "samsung,exynos7885-cmu-peri",
+ exynos7885_cmu_peri_init);
+
+/* ---- CMU_CORE ------------------------------------------------------------ */
+
+/* Register Offset definitions for CMU_CORE (0x12000000) */
+#define PLL_CON0_MUX_CLKCMU_CORE_BUS_USER 0x0100
+#define PLL_CON0_MUX_CLKCMU_CORE_CCI_USER 0x0120
+#define PLL_CON0_MUX_CLKCMU_CORE_G3D_USER 0x0140
+#define CLK_CON_MUX_MUX_CLK_CORE_GIC 0x1000
+#define CLK_CON_DIV_DIV_CLK_CORE_BUSP 0x1800
+#define CLK_CON_GAT_GOUT_CORE_CCI_550_ACLK 0x2054
+#define CLK_CON_GAT_GOUT_CORE_GIC400_CLK 0x2058
+
+static const unsigned long core_clk_regs[] __initconst = {
+ PLL_CON0_MUX_CLKCMU_CORE_BUS_USER,
+ PLL_CON0_MUX_CLKCMU_CORE_CCI_USER,
+ PLL_CON0_MUX_CLKCMU_CORE_G3D_USER,
+ CLK_CON_MUX_MUX_CLK_CORE_GIC,
+ CLK_CON_DIV_DIV_CLK_CORE_BUSP,
+ CLK_CON_GAT_GOUT_CORE_CCI_550_ACLK,
+ CLK_CON_GAT_GOUT_CORE_GIC400_CLK,
+};
+
+/* List of parent clocks for Muxes in CMU_CORE */
+PNAME(mout_core_bus_user_p) = { "oscclk", "dout_core_bus" };
+PNAME(mout_core_cci_user_p) = { "oscclk", "dout_core_cci" };
+PNAME(mout_core_g3d_user_p) = { "oscclk", "dout_core_g3d" };
+PNAME(mout_core_gic_p) = { "dout_core_busp", "oscclk" };
+
+static const struct samsung_mux_clock core_mux_clks[] __initconst = {
+ MUX(CLK_MOUT_CORE_BUS_USER, "mout_core_bus_user", mout_core_bus_user_p,
+ PLL_CON0_MUX_CLKCMU_CORE_BUS_USER, 4, 1),
+ MUX(CLK_MOUT_CORE_CCI_USER, "mout_core_cci_user", mout_core_cci_user_p,
+ PLL_CON0_MUX_CLKCMU_CORE_CCI_USER, 4, 1),
+ MUX(CLK_MOUT_CORE_G3D_USER, "mout_core_g3d_user", mout_core_g3d_user_p,
+ PLL_CON0_MUX_CLKCMU_CORE_G3D_USER, 4, 1),
+ MUX(CLK_MOUT_CORE_GIC, "mout_core_gic", mout_core_gic_p,
+ CLK_CON_MUX_MUX_CLK_CORE_GIC, 0, 1),
+};
+
+static const struct samsung_div_clock core_div_clks[] __initconst = {
+ DIV(CLK_DOUT_CORE_BUSP, "dout_core_busp", "mout_core_bus_user",
+ CLK_CON_DIV_DIV_CLK_CORE_BUSP, 0, 2),
+};
+
+static const struct samsung_gate_clock core_gate_clks[] __initconst = {
+ /* CCI (interconnect) clock must be always running */
+ GATE(CLK_GOUT_CCI_ACLK, "gout_cci_aclk", "mout_core_cci_user",
+ CLK_CON_GAT_GOUT_CORE_CCI_550_ACLK, 21, CLK_IS_CRITICAL, 0),
+ /* GIC (interrupt controller) clock must be always running */
+ GATE(CLK_GOUT_GIC400_CLK, "gout_gic400_clk", "mout_core_gic",
+ CLK_CON_GAT_GOUT_CORE_GIC400_CLK, 21, CLK_IS_CRITICAL, 0),
+};
+
+static const struct samsung_cmu_info core_cmu_info __initconst = {
+ .mux_clks = core_mux_clks,
+ .nr_mux_clks = ARRAY_SIZE(core_mux_clks),
+ .div_clks = core_div_clks,
+ .nr_div_clks = ARRAY_SIZE(core_div_clks),
+ .gate_clks = core_gate_clks,
+ .nr_gate_clks = ARRAY_SIZE(core_gate_clks),
+ .nr_clk_ids = CORE_NR_CLK,
+ .clk_regs = core_clk_regs,
+ .nr_clk_regs = ARRAY_SIZE(core_clk_regs),
+ .clk_name = "dout_core_bus",
+};
+
+/* ---- platform_driver ----------------------------------------------------- */
+
+static int __init exynos7885_cmu_probe(struct platform_device *pdev)
+{
+ const struct samsung_cmu_info *info;
+ struct device *dev = &pdev->dev;
+
+ info = of_device_get_match_data(dev);
+ exynos_arm64_register_cmu(dev, dev->of_node, info);
+
+ return 0;
+}
+
+static const struct of_device_id exynos7885_cmu_of_match[] = {
+ {
+ .compatible = "samsung,exynos7885-cmu-core",
+ .data = &core_cmu_info,
+ }, {
+ },
+};
+
+static struct platform_driver exynos7885_cmu_driver __refdata = {
+ .driver = {
+ .name = "exynos7885-cmu",
+ .of_match_table = exynos7885_cmu_of_match,
+ .suppress_bind_attrs = true,
+ },
+ .probe = exynos7885_cmu_probe,
+};
+
+static int __init exynos7885_cmu_init(void)
+{
+ return platform_driver_register(&exynos7885_cmu_driver);
+}
+core_initcall(exynos7885_cmu_init);
--
2.34.1


2021-12-05 22:12:58

by David Virag

[permalink] [raw]
Subject: [PATCH v2 7/7] arm64: dts: exynos: Add initial device tree support for Exynos7885 SoC

Add initial Exynos7885 device tree nodes with dts for the Samsung Galaxy
A8 (2018), a.k.a. "jackpotlte", with model number "SM-A530F".
Currently this includes some clock support, UART support, and I2C nodes.

Signed-off-by: David Virag <[email protected]>
---
Changes in v2:
- Remove address-cells, and size-cells from dts, since they are
already in the dtsi.
- Lower case hex in memory node
- Fix node names with underscore instead of hyphen
- Fix line breaks
- Fix "-key" missing from gpio keys node names
- Use the form without "key" in gpio key labels on all keys
- Suffix pin configuration node names with "-pins"
- Remove "fimc_is_mclk" nodes from pinctrl dtsi for now
- Use macros for "samsung,pin-con-pdn", and "samsung,pin-con-pdn"
- Add comment about Arm PMU
- Rename "clock-oscclk" to "osc-clock"
- Include exynos-syscon-restart.dtsi instead of rewriting its contents

arch/arm64/boot/dts/exynos/Makefile | 7 +-
.../boot/dts/exynos/exynos7885-jackpotlte.dts | 95 ++
.../boot/dts/exynos/exynos7885-pinctrl.dtsi | 865 ++++++++++++++++++
arch/arm64/boot/dts/exynos/exynos7885.dtsi | 438 +++++++++
4 files changed, 1402 insertions(+), 3 deletions(-)
create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
create mode 100644 arch/arm64/boot/dts/exynos/exynos7885.dtsi

diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile
index b41e86df0a84..c68c4ad577ac 100644
--- a/arch/arm64/boot/dts/exynos/Makefile
+++ b/arch/arm64/boot/dts/exynos/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_EXYNOS) += \
- exynos5433-tm2.dtb \
- exynos5433-tm2e.dtb \
- exynos7-espresso.dtb \
+ exynos5433-tm2.dtb \
+ exynos5433-tm2e.dtb \
+ exynos7-espresso.dtb \
+ exynos7885-jackpotlte.dtb \
exynosautov9-sadk.dtb
diff --git a/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts b/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
new file mode 100644
index 000000000000..f5941dc4c374
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Galaxy A8 2018 (jackpotlte/SM-A530F) device tree source
+ *
+ * Copyright (c) 2021 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2021 Dávid Virág
+ *
+ */
+
+/dts-v1/;
+#include "exynos7885.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Samsung Galaxy A8 (2018)";
+ compatible = "samsung,jackpotlte", "samsung,exynos7885";
+ chassis-type = "handset";
+
+ aliases {
+ serial0 = &serial_0;
+ serial1 = &serial_1;
+ serial2 = &serial_2;
+ };
+
+ chosen {
+ stdout-path = &serial_2;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x3da00000>,
+ <0x0 0xc0000000 0x40000000>,
+ <0x8 0x80000000 0x40000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&key_volup &key_voldown &key_power>;
+
+ volup-key {
+ label = "Volume Up";
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-parent = <&gpa1>;
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&gpa1 5 GPIO_ACTIVE_LOW>;
+ };
+
+ voldown-key {
+ label = "Volume Down";
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-parent = <&gpa1>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpios = <&gpa1 6 GPIO_ACTIVE_LOW>;
+ };
+
+ power-key {
+ label = "Power";
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-parent = <&gpa1>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpa1 7 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+ };
+};
+
+&serial_2 {
+ status = "okay";
+};
+
+&pinctrl_alive {
+ key_volup: key-volup-pins {
+ samsung,pins = "gpa1-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ };
+
+ key_voldown: key-voldown-pins {
+ samsung,pins = "gpa1-6";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ };
+
+ key_power: key-power-pins {
+ samsung,pins = "gpa1-7";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
new file mode 100644
index 000000000000..741d5cceafab
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
@@ -0,0 +1,865 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Exynos7885 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2017 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2021 Dávid Virág
+ *
+ * Samsung's Exynos7885 SoC pin-mux and pin-config options are listed as
+ * device tree nodes in this file.
+ */
+
+#include <dt-bindings/pinctrl/samsung.h>
+
+&pinctrl_alive {
+ etc0: etc0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ etc1: etc1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpa0: gpa0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpa1: gpa1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpa2: gpa2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpq0: gpq0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ sim1_det_gpio: sim1-det-gpio-pins {
+ samsung,pins = "gpa2-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ sim0_det_gpio: sim0-det-gpio-pins {
+ samsung,pins = "gpa2-6";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ speedy_bus: speedy-bus-pins {
+ samsung,pins = "gpq0-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ /* UART_DEBUG */
+ uart2_bus: uart2-bus-pins {
+ samsung,pins = "gpq0-4", "gpq0-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+};
+
+&pinctrl_dispaud {
+ gpb0: gpb0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb1: gpb1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb2: gpb2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ aud_codec_mclk: aud-codec-mclk-pins {
+ samsung,pins = "gpb0-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_codec_mclk_idle: aud-codec-mclk-idle-pins {
+ samsung,pins = "gpb0-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_codec_bus: aud-codec-bus-pins {
+ samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_codec_bus_idle: aud-codec-bus-idle-pins {
+ samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_loopback_bus: aud-loopback-bus{
+ samsung,pins = "gpb1-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_loopback_bus_idle: aud-loopback-bus-idle{
+ samsung,pins = "gpb1-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_fm_bus: aud-fm-bus-pins {
+ samsung,pins = "gpb1-1", "gpb1-2", "gpb1-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_fm_bus_idle: aud-fm-bus-idle-pins {
+ samsung,pins = "gpb1-1", "gpb1-2", "gpb1-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_spk_bus: aud-spk-bus-pins {
+ samsung,pins = "gpb2-0", "gpb2-1", "gpb2-2", "gpb2-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+
+ aud_spk_bus_idle: aud-spk-bus-idle-pins {
+ samsung,pins = "gpb2-0", "gpb2-1", "gpb2-2", "gpb2-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ };
+};
+
+&pinctrl_fsys {
+ gpf0: gpf0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf2: gpf2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf3: gpf3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf4: gpf4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ sd0_clk: sd0-clk-pins {
+ samsung,pins = "gpf0-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x-pins {
+ samsung,pins = "gpf0-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ };
+
+ sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x-pins {
+ samsung,pins = "gpf0-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <1>;
+ };
+
+ sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x-pins {
+ samsung,pins = "gpf0-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x-pins {
+ samsung,pins = "gpf0-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_cmd: sd0-cmd-pins {
+ samsung,pins = "gpf0-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_rdqs: sd0-rdqs-pins {
+ samsung,pins = "gpf0-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus1: sd0-bus-width1-pins {
+ samsung,pins = "gpf2-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus4: sd0-bus-width4-pins {
+ samsung,pins = "gpf2-1", "gpf2-2", "gpf2-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus8: sd0-bus-width8-pins {
+ samsung,pins = "gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_clk: sd1-clk-pins {
+ samsung,pins = "gpf3-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd1_clk_fast_slew_rate_1x: sd1-clk-fast-slew-rate-1x-pins {
+ samsung,pins = "gpf3-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ };
+
+ sd1_clk_fast_slew_rate_2x: sd1-clk-fast-slew-rate-2x-pins {
+ samsung,pins = "gpf3-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <1>;
+ };
+
+ sd1_clk_fast_slew_rate_3x: sd1-clk-fast-slew-rate-3x-pins {
+ samsung,pins = "gpf3-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd1_clk_fast_slew_rate_4x: sd1-clk-fast-slew-rate-4x-pins {
+ samsung,pins = "gpf3-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_cmd: sd1-cmd-pins {
+ samsung,pins = "gpf3-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd1_bus1: sd1-bus-width1-pins {
+ samsung,pins = "gpf3-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd1_bus4: sd1-bus-width4-pins {
+ samsung,pins = "gpf3-3", "gpf3-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd2_clk: sd2-clk-pins {
+ samsung,pins = "gpf4-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x-pins {
+ samsung,pins = "gpf4-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ };
+
+ sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x-pins {
+ samsung,pins = "gpf4-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <1>;
+ };
+
+ sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x-pins {
+ samsung,pins = "gpf4-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x-pins {
+ samsung,pins = "gpf4-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_cmd: sd2-cmd-pins {
+ samsung,pins = "gpf4-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd2_bus1: sd2-bus-width1-pins {
+ samsung,pins = "gpf4-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd2_bus4: sd2-bus-width4-pins {
+ samsung,pins = "gpf4-3", "gpf4-4", "gpf4-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <2>;
+ };
+};
+
+&pinctrl_top {
+ gpc0: gpc0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc1: gpc1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc2: gpc2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg0: gpg0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg1: gpg1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg2: gpg2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg3: gpg3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg4: gpg4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp0: gpp0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp1: gpp1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp2: gpp2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp3: gpp3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp4: gpp4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp5: gpp5 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp6: gpp6 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp7: gpp7 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpp8: gpp8 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ /* DECON TE */
+ decon_f_te_on: decon_f_te_on {
+ samsung,pins = "gpc0-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+ };
+
+ decon_f_te_off: decon_f_te_off {
+ samsung,pins = "gpc0-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ };
+
+ hs_i2c0_bus: hs-i2c0-bus {
+ samsung,pins = "gpc1-1", "gpc1-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ };
+
+ hs_i2c1_bus: hs-i2c1-bus {
+ samsung,pins = "gpc1-3", "gpc1-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ hs_i2c2_bus: hs-i2c2-bus {
+ samsung,pins = "gpc1-5", "gpc1-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ hs_i2c3_bus: hs-i2c3-bus {
+ samsung,pins = "gpc1-7", "gpc1-6";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ /* USI0 UART */
+ uart3_bus_single: uart3-bus-single {
+ samsung,pins = "gpc2-3", "gpc2-2", "gpc2-1", "gpc2-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ /* USI0 UART_HSI2C1 */
+ uart3_bus_dual: uart3-bus-dual {
+ samsung,pins = "gpc2-1", "gpc2-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ /* USI0 HSI2C0 */
+ hs_i2c4_bus: hs-i2c4-bus {
+ samsung,pins = "gpc2-1", "gpc2-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ /* USI0 HSI2C1 */
+ hs_i2c5_bus: hs-i2c5-bus {
+ samsung,pins = "gpc2-3", "gpc2-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ /* USI0 SPI */
+ spi2_bus: spi2-bus {
+ samsung,pins = "gpc2-1", "gpc2-0", "gpc2-3";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi2_cs: spi2-cs {
+ samsung,pins = "gpc2-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ /* USI1 UART */
+ uart4_bus_single: uart4-bus-single {
+ samsung,pins = "gpc2-7", "gpc2-6", "gpc2-5", "gpc2-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ /* USI1 UART_HSI2C1*/
+ uart4_bus_dual: uart4-bus-dual {
+ samsung,pins = "gpc2-5", "gpc2-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ /* USI1 HSI2C0 */
+ hs_i2c6_bus: hs-i2c6-bus {
+ samsung,pins = "gpc2-5", "gpc2-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ /* USI1 HSI2C1 */
+ hs_i2c7_bus: hs-i2c7-bus {
+ samsung,pins = "gpc2-7", "gpc2-6";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ /* USI1 SPI */
+ spi3_bus: spi3-bus {
+ samsung,pins = "gpc2-5", "gpc2-4", "gpc2-7";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi3_cs: spi3-cs {
+ samsung,pins = "gpc2-6";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ fm_lna_en: fm-lna-en {
+ samsung,pins = "gpg0-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-val = <1>;
+ };
+
+ uart1_bus: uart1-bus {
+ samsung,pins = "gpg1-3", "gpg1-2", "gpg1-1", "gpg1-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ i2c7_bus: i2c7-bus {
+ samsung,pins = "gpg1-5", "gpg1-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ aud_dmic_on: aud_dmic_on {
+ samsung,pins = "gpg2-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+ samsung,pin-val = <1>;
+ };
+
+ aud_dmic_off: aud_dmic_off {
+ samsung,pins = "gpg2-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+ samsung,pin-val = <0>;
+ };
+
+ /* UART_HEALTH */
+ uart0_bus: uart0-bus {
+ samsung,pins = "gpp0-3", "gpp0-2", "gpp0-1", "gpp0-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ i2c0_bus: i2c0-bus {
+ samsung,pins = "gpp1-1", "gpp1-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c1_bus: i2c1-bus {
+ samsung,pins = "gpp1-3", "gpp1-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c2_bus: i2c2-bus {
+ samsung,pins = "gpp2-1", "gpp2-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c3_bus: i2c3-bus {
+ samsung,pins = "gpp3-1", "gpp3-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c4_bus: i2c4-bus {
+ samsung,pins = "gpp4-1", "gpp4-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c5_bus: i2c5-bus {
+ samsung,pins = "gpp4-3", "gpp4-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c6_bus: i2c6-bus {
+ samsung,pins = "gpp4-5", "gpp4-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ /* SPI_ESE */
+ spi0_bus: spi0-bus {
+ samsung,pins = "gpp5-3", "gpp5-2", "gpp5-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi0_cs: spi0-cs {
+ samsung,pins = "gpp5-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ /* SPI_FP */
+ spi1_bus: spi1-bus {
+ samsung,pins = "gpp6-3", "gpp6-2", "gpp6-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi1_cs: spi1-cs {
+ samsung,pins = "gpp6-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ /* USI2 UART */
+ uart5_bus_single: uart5-bus-single {
+ samsung,pins = "gpp8-1", "gpp8-0", "gpp7-1", "gpp7-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ /* USI2 UART_HSI2C1 */
+ uart5_bus_dual: uart5-bus-dual {
+ samsung,pins = "gpp7-1", "gpp7-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ };
+
+ /* USI2 HSI2C0 */
+ hs_i2c8_bus: hs-i2c8-bus {
+ samsung,pins = "gpp7-1", "gpp7-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ /* USI2 HSI2C1 */
+ hs_i2c9_bus: hs-i2c9-bus {
+ samsung,pins = "gpp8-1", "gpp8-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <0>;
+ samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+ samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+ };
+
+ /* USI2 SPI */
+ spi4_bus: spi4-bus {
+ samsung,pins = "gpp7-1", "gpp7-0", "gpp8-1";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi4_cs: spi4-cs {
+ samsung,pins = "gpp8-0";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos7885.dtsi b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
new file mode 100644
index 000000000000..e85a6b988beb
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Exynos7885 SoC device tree source
+ *
+ * Copyright (c) 2021 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2021 Dávid Virág
+ *
+ */
+
+#include <dt-bindings/clock/exynos7885.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "samsung,exynos7885";
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ interrupt-parent = <&gic>;
+
+ aliases {
+ pinctrl0 = &pinctrl_alive;
+ pinctrl1 = &pinctrl_dispaud;
+ pinctrl2 = &pinctrl_fsys;
+ pinctrl3 = &pinctrl_top;
+ };
+
+ /*
+ * We should have two seperate nodes for a53 and a73, but we have
+ * no documentation about which interrupts belong to which one.
+ */
+ arm-pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu6>,
+ <&cpu7>,
+ <&cpu0>,
+ <&cpu1>,
+ <&cpu2>,
+ <&cpu3>,
+ <&cpu4>,
+ <&cpu5>;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ core4 {
+ cpu = <&cpu4>;
+ };
+ core5 {
+ cpu = <&cpu5>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu6>;
+ };
+ core1 {
+ cpu = <&cpu7>;
+ };
+ };
+ };
+
+ cpu0: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x100>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x101>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x102>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x103>;
+ enable-method = "psci";
+ };
+
+ cpu4: cpu@200 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x200>;
+ enable-method = "psci";
+ };
+
+ cpu5: cpu@201 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x201>;
+ enable-method = "psci";
+ };
+
+ cpu6: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x0>;
+ enable-method = "psci";
+ };
+
+ cpu7: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x1>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci";
+ method = "smc";
+ cpu_suspend = <0xc4000001>;
+ cpu_off = <0x84000002>;
+ cpu_on = <0xc4000003>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ /* Hypervisor Virtual Timer interrupt is not wired to GIC */
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ fixed-rate-clocks {
+ oscclk: osc-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "oscclk";
+ };
+ };
+
+ soc: soc@0 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x0 0x20000000>;
+
+ chipid@10000000 {
+ compatible = "samsung,exynos850-chipid";
+ reg = <0x10000000 0x24>;
+ };
+
+ gic: interrupt-controller@12301000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x12301000 0x1000>,
+ <0x12302000 0x2000>,
+ <0x12304000 0x2000>,
+ <0x12306000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ cmu_peri: clock-controller@0x10010000 {
+ compatible = "samsung,exynos7885-cmu-peri";
+ reg = <0x10010000 0x8000>;
+ #clock-cells = <1>;
+
+ clocks = <&oscclk>,
+ <&cmu_top CLK_DOUT_PERI_BUS>,
+ <&cmu_top CLK_DOUT_PERI_SPI0>,
+ <&cmu_top CLK_DOUT_PERI_SPI1>,
+ <&cmu_top CLK_DOUT_PERI_UART0>,
+ <&cmu_top CLK_DOUT_PERI_UART1>,
+ <&cmu_top CLK_DOUT_PERI_UART2>,
+ <&cmu_top CLK_DOUT_PERI_USI0>,
+ <&cmu_top CLK_DOUT_PERI_USI1>,
+ <&cmu_top CLK_DOUT_PERI_USI2>;
+ clock-names = "oscclk",
+ "dout_peri_bus",
+ "dout_peri_spi0",
+ "dout_peri_spi1",
+ "dout_peri_uart0",
+ "dout_peri_uart1",
+ "dout_peri_uart2",
+ "dout_peri_usi0",
+ "dout_peri_usi1",
+ "dout_peri_usi2";
+ };
+
+ cmu_core: clock-controller@0x12000000 {
+ compatible = "samsung,exynos7885-cmu-core";
+ reg = <0x12000000 0x8000>;
+ #clock-cells = <1>;
+
+ clocks = <&oscclk>,
+ <&cmu_top CLK_DOUT_CORE_BUS>,
+ <&cmu_top CLK_DOUT_CORE_CCI>,
+ <&cmu_top CLK_DOUT_CORE_G3D>;
+ clock-names = "oscclk", "dout_core_bus", "dout_core_cci", "dout_core_g3d";
+ };
+
+ cmu_top: clock-controller@0x12060000 {
+ compatible = "samsung,exynos7885-cmu-top";
+ reg = <0x12060000 0x8000>;
+ #clock-cells = <1>;
+
+ clocks = <&oscclk>;
+ clock-names = "oscclk";
+ };
+
+ pinctrl_alive: pinctrl@11cb0000 {
+ compatible = "samsung,exynos7885-pinctrl";
+ reg = <0x11cb0000 0x1000>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+
+ wakeup-interrupt-controller {
+ compatible = "samsung,exynos7-wakeup-eint";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ pinctrl_dispaud: pinctrl@148f0000 {
+ compatible = "samsung,exynos7885-pinctrl";
+ reg = <0x148f0000 0x1000>;
+ interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pinctrl_fsys: pinctrl@13430000 {
+ compatible = "samsung,exynos7885-pinctrl";
+ reg = <0x13430000 0x1000>;
+ interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pinctrl_top: pinctrl@139b0000 {
+ compatible = "samsung,exynos7885-pinctrl";
+ reg = <0x139b0000 0x1000>;
+ interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pmu_system_controller: system-controller@11c80000 {
+ compatible = "samsung,exynos7-pmu", "syscon";
+ reg = <0x11c80000 0x10000>;
+ };
+
+ serial_0: serial@13800000 {
+ compatible = "samsung,exynos5433-uart";
+ reg = <0x13800000 0x100>;
+ interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_bus>;
+ clocks = <&cmu_peri CLK_GOUT_UART0_EXT_UCLK>,
+ <&cmu_peri CLK_GOUT_UART0_PCLK>;
+ clock-names = "uart", "clk_uart_baud0";
+ samsung,uart-fifosize = <64>;
+ status = "disabled";
+ };
+
+ serial_1: serial@13810000 {
+ compatible = "samsung,exynos5433-uart";
+ reg = <0x13810000 0x100>;
+ interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_bus>;
+ clocks = <&cmu_peri CLK_GOUT_UART1_EXT_UCLK>,
+ <&cmu_peri CLK_GOUT_UART1_PCLK>;
+ clock-names = "uart", "clk_uart_baud0";
+ samsung,uart-fifosize = <256>;
+ status = "disabled";
+ };
+
+ serial_2: serial@13820000 {
+ compatible = "samsung,exynos5433-uart";
+ reg = <0x13820000 0x100>;
+ interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_bus>;
+ clocks = <&cmu_peri CLK_GOUT_UART2_EXT_UCLK>,
+ <&cmu_peri CLK_GOUT_UART2_PCLK>;
+ clock-names = "uart", "clk_uart_baud0";
+ samsung,uart-fifosize = <256>;
+ status = "disabled";
+ };
+
+ i2c_0: i2c@13830000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13830000 0x100>;
+ interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+ clocks = <&cmu_peri CLK_GOUT_I2C0_PCLK>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
+
+ i2c_1: i2c@13840000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13840000 0x100>;
+ interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+ clocks = <&cmu_peri CLK_GOUT_I2C1_PCLK>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
+
+ i2c_2: i2c@13850000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13850000 0x100>;
+ interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+ clocks = <&cmu_peri CLK_GOUT_I2C2_PCLK>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
+
+ i2c_3: i2c@13860000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13860000 0x100>;
+ interrupts = <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
+ clocks = <&cmu_peri CLK_GOUT_I2C3_PCLK>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
+
+ i2c_4: i2c@13870000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13870000 0x100>;
+ interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_bus>;
+ clocks = <&cmu_peri CLK_GOUT_I2C4_PCLK>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
+
+ i2c_5: i2c@13880000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13880000 0x100>;
+ interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_bus>;
+ clocks = <&cmu_peri CLK_GOUT_I2C5_PCLK>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
+
+ i2c_6: i2c@13890000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13890000 0x100>;
+ interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_bus>;
+ clocks = <&cmu_peri CLK_GOUT_I2C6_PCLK>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
+
+ i2c_7: i2c@11cd0000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x11cd0000 0x100>;
+ interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_bus>;
+ clocks = <&cmu_peri CLK_GOUT_I2C7_PCLK>;
+ clock-names = "i2c";
+ status = "disabled";
+ };
+ };
+};
+
+#include "exynos7885-pinctrl.dtsi"
+#include "arm/exynos-syscon-restart.dtsi"
--
2.34.1