This series is the v8 series that attempts to support media controller in the
atmel ISC and XISC drivers.
The CSI2DC driver was accepted thus removed from the patch series, together with
other patches.
Important note: this series applies on top of current media_staging tree, as it
relies on previous patches in the series which were accepted.
Thanks to everyone who reviewed my work !
Eugen
Changes in v8:
-> scaler: modified crop bounds to have the exact source size
Changes in v7:
-> scaler: modified crop bounds to have maximum isc size
-> format propagation: did small changes as per Jacopo review
Changes in v6:
-> worked a bit on scaler, added try crop and other changes as per Jacopo review
-> worked on isc-base enum_fmt , reworked as per Jacopo review
Changes in v5:
-> removed patch that removed the 'stop' variable as it was still required
-> added two new trivial patches
-> reworked some parts of the scaler and format propagation after discussions with Jacopo
Changes in v4:
-> as reviewed by Hans, added new patch to remove the 'stop' variable and reworked
one patch that was using it
-> as reviewed by Jacopo, reworked some parts of the media controller implementation
Changes in v3:
- change in bindings, small fixes in csi2dc driver and conversion to mc
for the isc-base.
- removed some MAINTAINERS patches and used patterns in MAINTAINERS
Changes in v2:
- integrated many changes suggested by Jacopo in the review of the v1 series.
- add a few new patches
Eugen Hristev (13):
media: atmel: atmel-isc-base: use streaming status when queueing
buffers
media: atmel: atmel-isc-base: replace is_streaming call in
s_fmt_vid_cap
media: atmel: atmel-isc: remove redundant comments
media: atmel: atmel-isc: implement media controller
media: atmel: atmel-sama5d2-isc: fix wrong mask in YUYV format check
media: atmel: atmel-isc-base: use mutex to lock awb workqueue from
streaming
media: atmel: atmel-isc: compact the controller formats list
media: atmel: atmel-isc: change format propagation to subdev into only
verification
media: atmel: atmel-sama7g5-isc: remove stray line
dt-bindings: media: microchip,xisc: add bus-width of 14
ARM: dts: at91: sama7g5: add nodes for video capture
ARM: configs: at91: sama7: add xisc and csi2dc
ARM: multi_v7_defconfig: add atmel video pipeline modules
.../bindings/media/microchip,xisc.yaml | 2 +-
arch/arm/boot/dts/sama7g5.dtsi | 49 ++
arch/arm/configs/multi_v7_defconfig | 3 +
arch/arm/configs/sama7_defconfig | 2 +
drivers/media/platform/atmel/Makefile | 2 +-
drivers/media/platform/atmel/atmel-isc-base.c | 518 ++++++++++--------
.../media/platform/atmel/atmel-isc-scaler.c | 267 +++++++++
drivers/media/platform/atmel/atmel-isc.h | 58 +-
.../media/platform/atmel/atmel-sama5d2-isc.c | 87 +--
.../media/platform/atmel/atmel-sama7g5-isc.c | 93 ++--
10 files changed, 754 insertions(+), 327 deletions(-)
create mode 100644 drivers/media/platform/atmel/atmel-isc-scaler.c
--
2.25.1
In s_fmt_vid_cap, we should check if vb2_is_busy and return EBUSY,
not check if it's streaming to return the busy state.
Suggested-by: Hans Verkuil <[email protected]>
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
drivers/media/platform/atmel/atmel-isc-base.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/media/platform/atmel/atmel-isc-base.c b/drivers/media/platform/atmel/atmel-isc-base.c
index d2cc6c99984f..67b4a2323fed 100644
--- a/drivers/media/platform/atmel/atmel-isc-base.c
+++ b/drivers/media/platform/atmel/atmel-isc-base.c
@@ -1029,7 +1029,7 @@ static int isc_s_fmt_vid_cap(struct file *file, void *priv,
{
struct isc_device *isc = video_drvdata(file);
- if (vb2_is_streaming(&isc->vb2_vidq))
+ if (vb2_is_busy(&isc->vb2_vidq))
return -EBUSY;
return isc_set_fmt(isc, f);
--
2.25.1
During experiments with libcamera, it looks like vb2_is_streaming returns
true before our start streaming is called.
Order of operations is streamon -> queue -> start_streaming
ISC would have started the DMA immediately when a buffer is being added
to the vbqueue if the queue is streaming.
It is more safe to start the DMA after the start streaming of the driver is
called.
Thus, even if vb2queue is streaming, add the buffer to the dma queue of the
driver instead of actually starting the DMA process, if the start streaming
has not been called yet.
Tho achieve this, we have to use vb2_start_streaming_called instead of
vb2_is_streaming.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
drivers/media/platform/atmel/atmel-isc-base.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/media/platform/atmel/atmel-isc-base.c b/drivers/media/platform/atmel/atmel-isc-base.c
index db15770d5b88..d2cc6c99984f 100644
--- a/drivers/media/platform/atmel/atmel-isc-base.c
+++ b/drivers/media/platform/atmel/atmel-isc-base.c
@@ -442,7 +442,7 @@ static void isc_buffer_queue(struct vb2_buffer *vb)
spin_lock_irqsave(&isc->dma_queue_lock, flags);
if (!isc->cur_frm && list_empty(&isc->dma_queue) &&
- vb2_is_streaming(vb->vb2_queue)) {
+ vb2_start_streaming_called(vb->vb2_queue)) {
isc->cur_frm = buf;
isc_start_dma(isc);
} else
--
2.25.1
Remove duplicate comments which are already in place before the struct
definition.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
drivers/media/platform/atmel/atmel-isc.h | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/media/platform/atmel/atmel-isc.h b/drivers/media/platform/atmel/atmel-isc.h
index 07fa6dbf8460..f9ad7ec6bd13 100644
--- a/drivers/media/platform/atmel/atmel-isc.h
+++ b/drivers/media/platform/atmel/atmel-isc.h
@@ -272,7 +272,7 @@ struct isc_device {
struct video_device video_dev;
struct vb2_queue vb2_vidq;
- spinlock_t dma_queue_lock; /* serialize access to dma queue */
+ spinlock_t dma_queue_lock;
struct list_head dma_queue;
struct isc_buffer *cur_frm;
unsigned int sequence;
@@ -289,8 +289,8 @@ struct isc_device {
struct isc_ctrls ctrls;
struct work_struct awb_work;
- struct mutex lock; /* serialize access to file operations */
- spinlock_t awb_lock; /* serialize access to DMA buffers from awb work queue */
+ struct mutex lock;
+ spinlock_t awb_lock;
struct regmap_field *pipeline[ISC_PIPE_LINE_NODE_NUM];
--
2.25.1
Implement the support for media-controller.
This means that the capabilities of the driver have changed and now
it also advertises the IO_MC .
The driver will register its media device, and add the video entity to this
media device. The subdevices are registered to the same media device.
The ISC will have a base entity which is auto-detected as atmel_isc_base.
It will also register a subdevice that allows cropping of the incoming frame
to the maximum frame size supported by the ISC.
The ISC will create a link between the subdevice that is asynchronously
registered and the atmel_isc_scaler entity.
Then, the atmel_isc_scaler and atmel_isc_base are connected through another
link.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
Changes in v8:
- use source format size as bounds always
Changes in v7:
- use maximum isc frame size as bounds always
Changes in v6:
- reworked a bit as suggested by Jacopo
- add try crops
Changes in v5:
- reworked s_fmt to pass the same format from sink to source
- simplified enum_mbus_code
- separated tgt and bounds to report correctly in g_sel
Changes in v4:
As suggested by Jacopo:
- renamed atmel_isc_mc to atmel_isc_scaler.c
- moved init_mc/clean_mc to isc_base file
Changes in v2:
- implement try formats
drivers/media/platform/atmel/Makefile | 2 +-
drivers/media/platform/atmel/atmel-isc-base.c | 75 ++++-
.../media/platform/atmel/atmel-isc-scaler.c | 262 ++++++++++++++++++
drivers/media/platform/atmel/atmel-isc.h | 37 +++
.../media/platform/atmel/atmel-sama5d2-isc.c | 14 +-
.../media/platform/atmel/atmel-sama7g5-isc.c | 12 +-
6 files changed, 394 insertions(+), 8 deletions(-)
create mode 100644 drivers/media/platform/atmel/atmel-isc-scaler.c
diff --git a/drivers/media/platform/atmel/Makefile b/drivers/media/platform/atmel/Makefile
index 794e8f739287..f02d03df89d6 100644
--- a/drivers/media/platform/atmel/Makefile
+++ b/drivers/media/platform/atmel/Makefile
@@ -1,7 +1,7 @@
# SPDX-License-Identifier: GPL-2.0-only
atmel-isc-objs = atmel-sama5d2-isc.o
atmel-xisc-objs = atmel-sama7g5-isc.o
-atmel-isc-common-objs = atmel-isc-base.o atmel-isc-clk.o
+atmel-isc-common-objs = atmel-isc-base.o atmel-isc-clk.o atmel-isc-scaler.o
obj-$(CONFIG_VIDEO_ATMEL_ISI) += atmel-isi.o
obj-$(CONFIG_VIDEO_ATMEL_ISC_BASE) += atmel-isc-common.o
diff --git a/drivers/media/platform/atmel/atmel-isc-base.c b/drivers/media/platform/atmel/atmel-isc-base.c
index 67b4a2323fed..448bf281c61a 100644
--- a/drivers/media/platform/atmel/atmel-isc-base.c
+++ b/drivers/media/platform/atmel/atmel-isc-base.c
@@ -1712,6 +1712,7 @@ static int isc_async_bound(struct v4l2_async_notifier *notifier,
struct isc_device, v4l2_dev);
struct isc_subdev_entity *subdev_entity =
container_of(notifier, struct isc_subdev_entity, notifier);
+ int pad;
if (video_is_registered(&isc->video_dev)) {
v4l2_err(&isc->v4l2_dev, "only supports one sub-device.\n");
@@ -1720,6 +1721,16 @@ static int isc_async_bound(struct v4l2_async_notifier *notifier,
subdev_entity->sd = subdev;
+ pad = media_entity_get_fwnode_pad(&subdev->entity, asd->match.fwnode,
+ MEDIA_PAD_FL_SOURCE);
+ if (pad < 0) {
+ v4l2_err(&isc->v4l2_dev, "failed to find pad for %s\n",
+ subdev->name);
+ return pad;
+ }
+
+ isc->remote_pad = pad;
+
return 0;
}
@@ -1734,8 +1745,8 @@ static void isc_async_unbind(struct v4l2_async_notifier *notifier,
v4l2_ctrl_handler_free(&isc->ctrls.handler);
}
-static struct isc_format *find_format_by_code(struct isc_device *isc,
- unsigned int code, int *index)
+struct isc_format *isc_find_format_by_code(struct isc_device *isc,
+ unsigned int code, int *index)
{
struct isc_format *fmt = &isc->formats_list[0];
unsigned int i;
@@ -1751,6 +1762,7 @@ static struct isc_format *find_format_by_code(struct isc_device *isc,
return NULL;
}
+EXPORT_SYMBOL_GPL(isc_find_format_by_code);
static int isc_formats_init(struct isc_device *isc)
{
@@ -1767,7 +1779,7 @@ static int isc_formats_init(struct isc_device *isc)
NULL, &mbus_code)) {
mbus_code.index++;
- fmt = find_format_by_code(isc, mbus_code.code, &i);
+ fmt = isc_find_format_by_code(isc, mbus_code.code, &i);
if (!fmt) {
v4l2_warn(&isc->v4l2_dev, "Mbus code %x not supported\n",
mbus_code.code);
@@ -1893,7 +1905,8 @@ static int isc_async_complete(struct v4l2_async_notifier *notifier)
vdev->queue = q;
vdev->lock = &isc->lock;
vdev->ctrl_handler = &isc->ctrls.handler;
- vdev->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_CAPTURE;
+ vdev->device_caps = V4L2_CAP_STREAMING | V4L2_CAP_VIDEO_CAPTURE |
+ V4L2_CAP_IO_MC;
video_set_drvdata(vdev, isc);
ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1);
@@ -1903,8 +1916,19 @@ static int isc_async_complete(struct v4l2_async_notifier *notifier)
goto isc_async_complete_err;
}
+ ret = isc_scaler_link(isc);
+ if (ret < 0)
+ goto isc_async_complete_unregister_device;
+
+ ret = media_device_register(&isc->mdev);
+ if (ret < 0)
+ goto isc_async_complete_unregister_device;
+
return 0;
+isc_async_complete_unregister_device:
+ video_unregister_device(vdev);
+
isc_async_complete_err:
mutex_destroy(&isc->lock);
return ret;
@@ -1971,6 +1995,49 @@ int isc_pipeline_init(struct isc_device *isc)
}
EXPORT_SYMBOL_GPL(isc_pipeline_init);
+int isc_mc_init(struct isc_device *isc, u32 ver)
+{
+ const struct of_device_id *match;
+ int ret;
+
+ isc->video_dev.entity.function = MEDIA_ENT_F_IO_V4L;
+ isc->video_dev.entity.flags = MEDIA_ENT_FL_DEFAULT;
+ isc->pads[ISC_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+
+ ret = media_entity_pads_init(&isc->video_dev.entity, ISC_PADS_NUM,
+ isc->pads);
+ if (ret < 0) {
+ dev_err(isc->dev, "media entity init failed\n");
+ return ret;
+ }
+
+ isc->mdev.dev = isc->dev;
+
+ match = of_match_node(isc->dev->driver->of_match_table,
+ isc->dev->of_node);
+
+ strscpy(isc->mdev.driver_name, KBUILD_MODNAME,
+ sizeof(isc->mdev.driver_name));
+ strscpy(isc->mdev.model, match->compatible, sizeof(isc->mdev.model));
+ snprintf(isc->mdev.bus_info, sizeof(isc->mdev.bus_info), "platform:%s",
+ isc->v4l2_dev.name);
+ isc->mdev.hw_revision = ver;
+
+ media_device_init(&isc->mdev);
+
+ isc->v4l2_dev.mdev = &isc->mdev;
+
+ return isc_scaler_init(isc);
+}
+EXPORT_SYMBOL_GPL(isc_mc_init);
+
+void isc_mc_cleanup(struct isc_device *isc)
+{
+ media_entity_cleanup(&isc->video_dev.entity);
+ media_device_cleanup(&isc->mdev);
+}
+EXPORT_SYMBOL_GPL(isc_mc_cleanup);
+
/* regmap configuration */
#define ATMEL_ISC_REG_MAX 0xd5c
const struct regmap_config isc_regmap_config = {
diff --git a/drivers/media/platform/atmel/atmel-isc-scaler.c b/drivers/media/platform/atmel/atmel-isc-scaler.c
new file mode 100644
index 000000000000..a1ca4633787c
--- /dev/null
+++ b/drivers/media/platform/atmel/atmel-isc-scaler.c
@@ -0,0 +1,262 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Microchip Image Sensor Controller (ISC) Scaler entity support
+ *
+ * Copyright (C) 2022 Microchip Technology, Inc.
+ *
+ * Author: Eugen Hristev <[email protected]>
+ *
+ */
+
+#include <media/media-device.h>
+#include <media/media-entity.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-subdev.h>
+
+#include "atmel-isc-regs.h"
+#include "atmel-isc.h"
+
+static void isc_scaler_prepare_fmt(struct v4l2_mbus_framefmt *framefmt)
+{
+ framefmt->colorspace = V4L2_COLORSPACE_SRGB;
+ framefmt->field = V4L2_FIELD_NONE;
+ framefmt->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
+ framefmt->quantization = V4L2_QUANTIZATION_DEFAULT;
+ framefmt->xfer_func = V4L2_XFER_FUNC_DEFAULT;
+};
+
+static int isc_scaler_get_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_format *format)
+{
+ struct isc_device *isc = container_of(sd, struct isc_device, scaler_sd);
+ struct v4l2_mbus_framefmt *v4l2_try_fmt;
+
+ if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
+ v4l2_try_fmt = v4l2_subdev_get_try_format(sd, sd_state,
+ format->pad);
+ format->format = *v4l2_try_fmt;
+
+ return 0;
+ }
+
+ format->format = isc->scaler_format[format->pad];
+
+ return 0;
+}
+
+static int isc_scaler_set_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_format *req_fmt)
+{
+ struct isc_device *isc = container_of(sd, struct isc_device, scaler_sd);
+ struct v4l2_mbus_framefmt *v4l2_try_fmt;
+ struct isc_format *fmt;
+ unsigned int i;
+
+ /* Source format is fixed, we cannot change it */
+ if (req_fmt->pad == ISC_SCALER_PAD_SOURCE) {
+ req_fmt->format = isc->scaler_format[ISC_SCALER_PAD_SOURCE];
+ return 0;
+ }
+
+ /* There is no limit on the frame size on the sink pad */
+ v4l_bound_align_image(&req_fmt->format.width, 16, UINT_MAX, 0,
+ &req_fmt->format.height, 16, UINT_MAX, 0, 0);
+
+ isc_scaler_prepare_fmt(&req_fmt->format);
+
+ fmt = isc_find_format_by_code(isc, req_fmt->format.code, &i);
+
+ if (!fmt)
+ fmt = &isc->formats_list[0];
+
+ req_fmt->format.code = fmt->mbus_code;
+
+ if (req_fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
+ v4l2_try_fmt = v4l2_subdev_get_try_format(sd, sd_state,
+ req_fmt->pad);
+ *v4l2_try_fmt = req_fmt->format;
+ /* Trying on the sink pad makes the source pad change too */
+ v4l2_try_fmt = v4l2_subdev_get_try_format(sd, sd_state,
+ ISC_SCALER_PAD_SOURCE);
+ *v4l2_try_fmt = req_fmt->format;
+
+ v4l_bound_align_image(&v4l2_try_fmt->width,
+ 16, isc->max_width, 0,
+ &v4l2_try_fmt->height,
+ 16, isc->max_height, 0, 0);
+ /* if we are just trying, we are done */
+ return 0;
+ }
+
+ isc->scaler_format[ISC_SCALER_PAD_SINK] = req_fmt->format;
+
+ /* The source pad is the same as the sink, but we have to crop it */
+ isc->scaler_format[ISC_SCALER_PAD_SOURCE] =
+ isc->scaler_format[ISC_SCALER_PAD_SINK];
+ v4l_bound_align_image
+ (&isc->scaler_format[ISC_SCALER_PAD_SOURCE].width, 16,
+ isc->max_width, 0,
+ &isc->scaler_format[ISC_SCALER_PAD_SOURCE].height, 16,
+ isc->max_height, 0, 0);
+
+ return 0;
+}
+
+static int isc_scaler_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ struct isc_device *isc = container_of(sd, struct isc_device, scaler_sd);
+
+ /*
+ * All formats supported by the ISC are supported by the scaler.
+ * Advertise the formats which the ISC can take as input, as the scaler
+ * entity cropping is part of the PFE module (parallel front end)
+ */
+ if (code->index < isc->formats_list_size) {
+ code->code = isc->formats_list[code->index].mbus_code;
+ return 0;
+ }
+
+ return -EINVAL;
+}
+
+static int isc_scaler_g_sel(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_selection *sel)
+{
+ struct isc_device *isc = container_of(sd, struct isc_device, scaler_sd);
+
+ if (sel->pad == ISC_SCALER_PAD_SOURCE)
+ return -EINVAL;
+
+ if (sel->target != V4L2_SEL_TGT_CROP_BOUNDS &&
+ sel->target != V4L2_SEL_TGT_CROP)
+ return -EINVAL;
+
+ sel->r.height = isc->scaler_format[ISC_SCALER_PAD_SOURCE].height;
+ sel->r.width = isc->scaler_format[ISC_SCALER_PAD_SOURCE].width;
+
+ sel->r.left = 0;
+ sel->r.top = 0;
+
+ return 0;
+}
+
+static int isc_scaler_init_cfg(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state)
+{
+ struct v4l2_mbus_framefmt *v4l2_try_fmt =
+ v4l2_subdev_get_try_format(sd, sd_state, 0);
+ struct v4l2_rect *try_crop;
+ struct isc_device *isc = container_of(sd, struct isc_device, scaler_sd);
+
+ *v4l2_try_fmt = isc->scaler_format[ISC_SCALER_PAD_SOURCE];
+
+ try_crop = v4l2_subdev_get_try_crop(sd, sd_state, 0);
+
+ try_crop->top = 0;
+ try_crop->left = 0;
+ try_crop->width = v4l2_try_fmt->width;
+ try_crop->height = v4l2_try_fmt->height;
+
+ return 0;
+}
+
+static const struct v4l2_subdev_pad_ops isc_scaler_pad_ops = {
+ .enum_mbus_code = isc_scaler_enum_mbus_code,
+ .set_fmt = isc_scaler_set_fmt,
+ .get_fmt = isc_scaler_get_fmt,
+ .get_selection = isc_scaler_g_sel,
+ .init_cfg = isc_scaler_init_cfg,
+};
+
+static const struct v4l2_subdev_ops xisc_scaler_subdev_ops = {
+ .pad = &isc_scaler_pad_ops,
+};
+
+int isc_scaler_init(struct isc_device *isc)
+{
+ int ret;
+
+ v4l2_subdev_init(&isc->scaler_sd, &xisc_scaler_subdev_ops);
+
+ isc->scaler_sd.owner = THIS_MODULE;
+ isc->scaler_sd.dev = isc->dev;
+ snprintf(isc->scaler_sd.name, sizeof(isc->scaler_sd.name),
+ "atmel_isc_scaler");
+
+ isc->scaler_sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ isc->scaler_sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_SCALER;
+ isc->scaler_pads[ISC_SCALER_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+ isc->scaler_pads[ISC_SCALER_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+ isc_scaler_prepare_fmt(&isc->scaler_format[ISC_SCALER_PAD_SOURCE]);
+ isc->scaler_format[ISC_SCALER_PAD_SOURCE].height = isc->max_height;
+ isc->scaler_format[ISC_SCALER_PAD_SOURCE].width = isc->max_width;
+ isc->scaler_format[ISC_SCALER_PAD_SOURCE].code =
+ isc->formats_list[0].mbus_code;
+
+ isc->scaler_format[ISC_SCALER_PAD_SINK] =
+ isc->scaler_format[ISC_SCALER_PAD_SOURCE];
+
+ ret = media_entity_pads_init(&isc->scaler_sd.entity,
+ ISC_SCALER_PADS_NUM,
+ isc->scaler_pads);
+ if (ret < 0) {
+ dev_err(isc->dev, "scaler sd media entity init failed\n");
+ return ret;
+ }
+
+ ret = v4l2_device_register_subdev(&isc->v4l2_dev, &isc->scaler_sd);
+ if (ret < 0) {
+ dev_err(isc->dev, "scaler sd failed to register subdev\n");
+ return ret;
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(isc_scaler_init);
+
+int isc_scaler_link(struct isc_device *isc)
+{
+ int ret;
+
+ ret = media_create_pad_link(&isc->current_subdev->sd->entity,
+ isc->remote_pad, &isc->scaler_sd.entity,
+ ISC_SCALER_PAD_SINK,
+ MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+
+ if (ret < 0) {
+ dev_err(isc->dev, "Failed to create pad link: %s to %s\n",
+ isc->current_subdev->sd->entity.name,
+ isc->scaler_sd.entity.name);
+ return ret;
+ }
+
+ dev_dbg(isc->dev, "link with %s pad: %d\n",
+ isc->current_subdev->sd->name, isc->remote_pad);
+
+ ret = media_create_pad_link(&isc->scaler_sd.entity,
+ ISC_SCALER_PAD_SOURCE,
+ &isc->video_dev.entity, ISC_PAD_SINK,
+ MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+
+ if (ret < 0) {
+ dev_err(isc->dev, "Failed to create pad link: %s to %s\n",
+ isc->scaler_sd.entity.name,
+ isc->video_dev.entity.name);
+ return ret;
+ }
+
+ dev_dbg(isc->dev, "link with %s pad: %d\n", isc->scaler_sd.name,
+ ISC_SCALER_PAD_SOURCE);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(isc_scaler_link);
+
diff --git a/drivers/media/platform/atmel/atmel-isc.h b/drivers/media/platform/atmel/atmel-isc.h
index f9ad7ec6bd13..9cc69c3ae26d 100644
--- a/drivers/media/platform/atmel/atmel-isc.h
+++ b/drivers/media/platform/atmel/atmel-isc.h
@@ -183,6 +183,17 @@ struct isc_reg_offsets {
u32 his_entry;
};
+enum isc_mc_pads {
+ ISC_PAD_SINK = 0,
+ ISC_PADS_NUM = 1,
+};
+
+enum isc_scaler_pads {
+ ISC_SCALER_PAD_SINK = 0,
+ ISC_SCALER_PAD_SOURCE = 1,
+ ISC_SCALER_PADS_NUM = 2,
+};
+
/*
* struct isc_device - ISC device driver data/config struct
* @regmap: Register map
@@ -258,6 +269,12 @@ struct isc_reg_offsets {
* be used as an input to the controller
* @controller_formats_size: size of controller_formats array
* @formats_list_size: size of formats_list array
+ * @pads: media controller pads for isc video entity
+ * @mdev: media device that is registered by the isc
+ * @remote_pad: remote pad on the connected subdevice
+ * @scaler_sd: subdevice for the scaler that isc registers
+ * @scaler_pads: media controller pads for the scaler subdevice
+ * @scaler_format: current format for the scaler subdevice
*/
struct isc_device {
struct regmap *regmap;
@@ -346,6 +363,19 @@ struct isc_device {
struct isc_format *formats_list;
u32 controller_formats_size;
u32 formats_list_size;
+
+ struct {
+ struct media_pad pads[ISC_PADS_NUM];
+ struct media_device mdev;
+
+ u32 remote_pad;
+ };
+
+ struct {
+ struct v4l2_subdev scaler_sd;
+ struct media_pad scaler_pads[ISC_SCALER_PADS_NUM];
+ struct v4l2_mbus_framefmt scaler_format[ISC_SCALER_PADS_NUM];
+ };
};
extern const struct regmap_config isc_regmap_config;
@@ -357,4 +387,11 @@ int isc_clk_init(struct isc_device *isc);
void isc_subdev_cleanup(struct isc_device *isc);
void isc_clk_cleanup(struct isc_device *isc);
+int isc_scaler_link(struct isc_device *isc);
+int isc_scaler_init(struct isc_device *isc);
+int isc_mc_init(struct isc_device *isc, u32 ver);
+void isc_mc_cleanup(struct isc_device *isc);
+
+struct isc_format *isc_find_format_by_code(struct isc_device *isc,
+ unsigned int code, int *index);
#endif
diff --git a/drivers/media/platform/atmel/atmel-sama5d2-isc.c b/drivers/media/platform/atmel/atmel-sama5d2-isc.c
index c5b9563e36cb..c244682ea22f 100644
--- a/drivers/media/platform/atmel/atmel-sama5d2-isc.c
+++ b/drivers/media/platform/atmel/atmel-sama5d2-isc.c
@@ -553,6 +553,12 @@ static int atmel_isc_probe(struct platform_device *pdev)
break;
}
+ regmap_read(isc->regmap, ISC_VERSION + isc->offsets.version, &ver);
+
+ ret = isc_mc_init(isc, ver);
+ if (ret < 0)
+ goto isc_probe_mc_init_err;
+
pm_runtime_set_active(dev);
pm_runtime_enable(dev);
pm_request_idle(dev);
@@ -562,7 +568,7 @@ static int atmel_isc_probe(struct platform_device *pdev)
ret = clk_prepare_enable(isc->ispck);
if (ret) {
dev_err(dev, "failed to enable ispck: %d\n", ret);
- goto cleanup_subdev;
+ goto isc_probe_mc_init_err;
}
/* ispck should be greater or equal to hclock */
@@ -572,7 +578,6 @@ static int atmel_isc_probe(struct platform_device *pdev)
goto unprepare_clk;
}
- regmap_read(isc->regmap, ISC_VERSION + isc->offsets.version, &ver);
dev_info(dev, "Microchip ISC version %x\n", ver);
return 0;
@@ -580,6 +585,9 @@ static int atmel_isc_probe(struct platform_device *pdev)
unprepare_clk:
clk_disable_unprepare(isc->ispck);
+isc_probe_mc_init_err:
+ isc_mc_cleanup(isc);
+
cleanup_subdev:
isc_subdev_cleanup(isc);
@@ -600,6 +608,8 @@ static int atmel_isc_remove(struct platform_device *pdev)
pm_runtime_disable(&pdev->dev);
+ isc_mc_cleanup(isc);
+
isc_subdev_cleanup(isc);
v4l2_device_unregister(&isc->v4l2_dev);
diff --git a/drivers/media/platform/atmel/atmel-sama7g5-isc.c b/drivers/media/platform/atmel/atmel-sama7g5-isc.c
index 07a80b08bc54..9dc75eed0098 100644
--- a/drivers/media/platform/atmel/atmel-sama7g5-isc.c
+++ b/drivers/media/platform/atmel/atmel-sama7g5-isc.c
@@ -547,15 +547,23 @@ static int microchip_xisc_probe(struct platform_device *pdev)
break;
}
+ regmap_read(isc->regmap, ISC_VERSION + isc->offsets.version, &ver);
+
+ ret = isc_mc_init(isc, ver);
+ if (ret < 0)
+ goto isc_probe_mc_init_err;
+
pm_runtime_set_active(dev);
pm_runtime_enable(dev);
pm_request_idle(dev);
- regmap_read(isc->regmap, ISC_VERSION + isc->offsets.version, &ver);
dev_info(dev, "Microchip XISC version %x\n", ver);
return 0;
+isc_probe_mc_init_err:
+ isc_mc_cleanup(isc);
+
cleanup_subdev:
isc_subdev_cleanup(isc);
@@ -576,6 +584,8 @@ static int microchip_xisc_remove(struct platform_device *pdev)
pm_runtime_disable(&pdev->dev);
+ isc_mc_cleanup(isc);
+
isc_subdev_cleanup(isc);
v4l2_device_unregister(&isc->v4l2_dev);
--
2.25.1
Remove stray line from formats struct.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
drivers/media/platform/atmel/atmel-sama7g5-isc.c | 1 -
1 file changed, 1 deletion(-)
diff --git a/drivers/media/platform/atmel/atmel-sama7g5-isc.c b/drivers/media/platform/atmel/atmel-sama7g5-isc.c
index a0d60cfdba7b..638af8da2694 100644
--- a/drivers/media/platform/atmel/atmel-sama7g5-isc.c
+++ b/drivers/media/platform/atmel/atmel-sama7g5-isc.c
@@ -225,7 +225,6 @@ static struct isc_format sama7g5_formats_list[] = {
.mbus_code = MEDIA_BUS_FMT_Y10_1X10,
.pfe_cfg0_bps = ISC_PFG_CFG0_BPS_TEN,
},
-
};
static void isc_sama7g5_config_csc(struct isc_device *isc)
--
2.25.1
Enable XISC and CSI2DC drivers.
Signed-off-by: Eugen Hristev <[email protected]>
---
arch/arm/configs/sama7_defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/configs/sama7_defconfig b/arch/arm/configs/sama7_defconfig
index 0368068e04d9..9918cff93e5b 100644
--- a/arch/arm/configs/sama7_defconfig
+++ b/arch/arm/configs/sama7_defconfig
@@ -127,6 +127,8 @@ CONFIG_MEDIA_SUPPORT_FILTER=y
CONFIG_MEDIA_CAMERA_SUPPORT=y
CONFIG_MEDIA_PLATFORM_SUPPORT=y
CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_ATMEL_XISC=y
+CONFIG_VIDEO_MICROCHIP_CSI2DC=y
CONFIG_VIDEO_IMX219=m
CONFIG_VIDEO_IMX274=m
CONFIG_VIDEO_OV5647=m
--
2.25.1
As a top MC video driver, the atmel-isc should not propagate the format to the
subdevice, it should rather check at start_streaming() time if the subdev is properly
configured with a compatible format.
Removed the whole format finding logic, and reworked the format verification
at start_streaming time, such that the ISC will return an error if the subdevice
is not properly configured. To achieve this, media_pipeline_start
is called and a link_validate callback is created to check the formats.
With this being done, the module parameter 'sensor_preferred' makes no sense
anymore. The ISC should not decide which format the sensor is using. The
ISC should only cope with the situation and inform userspace if the streaming
is possible in the current configuration.
The redesign of the format propagation has also risen the question of the
enumfmt callback. If enumfmt is called with an mbus_code, the enumfmt handler
should only return the formats that are supported for this mbus_code.
Otherwise, the enumfmt will report all the formats that the ISC could output.
With this rework, the dynamic list of user formats is removed. It makes no
more sense to identify at complete time which formats the sensor could emit,
and add those into a separate dynamic list.
The ISC will start with a simple preconfigured default format, and at
link validate time, decide whether it can use the format that is configured
on the sink or not.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
Changes in v7:
- minor typos as suggested by Jacopo
- small changes, reduce some indentation, modified an index, as suggested by
Jacopo
Changes in v6:
- reworked a bit enum_fmt as suggested by Jacopo
Changes in v5:
- removed user_formats dynamic list as it is now pointless
- greatly simplified the enum_fmt function
- removed some init code that was useless now
Changes in v4:
- moved validation code into link_validate and used media_pipeline_start
- merged this patch with the enum_fmt patch which was previously in v3 of
the series
Changes in v3:
- clamp to maximum resolution once the frame size from the subdev is found
drivers/media/platform/atmel/atmel-isc-base.c | 412 ++++++++----------
.../media/platform/atmel/atmel-isc-scaler.c | 5 +
drivers/media/platform/atmel/atmel-isc.h | 13 +-
.../media/platform/atmel/atmel-sama5d2-isc.c | 20 +
.../media/platform/atmel/atmel-sama7g5-isc.c | 20 +
5 files changed, 236 insertions(+), 234 deletions(-)
diff --git a/drivers/media/platform/atmel/atmel-isc-base.c b/drivers/media/platform/atmel/atmel-isc-base.c
index ee1dda6707a0..28937c6789b6 100644
--- a/drivers/media/platform/atmel/atmel-isc-base.c
+++ b/drivers/media/platform/atmel/atmel-isc-base.c
@@ -36,11 +36,6 @@ static unsigned int debug;
module_param(debug, int, 0644);
MODULE_PARM_DESC(debug, "debug level (0-2)");
-static unsigned int sensor_preferred = 1;
-module_param(sensor_preferred, uint, 0644);
-MODULE_PARM_DESC(sensor_preferred,
- "Sensor is preferred to output the specified format (1-on 0-off), default 1");
-
#define ISC_IS_FORMAT_RAW(mbus_code) \
(((mbus_code) & 0xf000) == 0x3000)
@@ -337,6 +332,10 @@ static int isc_start_streaming(struct vb2_queue *vq, unsigned int count)
unsigned long flags;
int ret;
+ ret = media_pipeline_start(&isc->video_dev.entity, &isc->mpipe);
+ if (ret)
+ goto err_pipeline_start;
+
/* Enable stream on the sub device */
ret = v4l2_subdev_call(isc->current_subdev->sd, video, s_stream, 1);
if (ret && ret != -ENOIOCTLCMD) {
@@ -385,6 +384,9 @@ static int isc_start_streaming(struct vb2_queue *vq, unsigned int count)
v4l2_subdev_call(isc->current_subdev->sd, video, s_stream, 0);
err_start_stream:
+ media_pipeline_stop(&isc->video_dev.entity);
+
+err_pipeline_start:
spin_lock_irqsave(&isc->dma_queue_lock, flags);
list_for_each_entry(buf, &isc->dma_queue, list)
vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED);
@@ -423,6 +425,9 @@ static void isc_stop_streaming(struct vb2_queue *vq)
if (ret && ret != -ENOIOCTLCMD)
v4l2_err(&isc->v4l2_dev, "stream off failed in subdev\n");
+ /* Stop media pipeline */
+ media_pipeline_stop(&isc->video_dev.entity);
+
/* Release all active buffers */
spin_lock_irqsave(&isc->dma_queue_lock, flags);
if (unlikely(isc->cur_frm)) {
@@ -453,22 +458,6 @@ static void isc_buffer_queue(struct vb2_buffer *vb)
spin_unlock_irqrestore(&isc->dma_queue_lock, flags);
}
-static struct isc_format *find_format_by_fourcc(struct isc_device *isc,
- unsigned int fourcc)
-{
- unsigned int num_formats = isc->num_user_formats;
- struct isc_format *fmt;
- unsigned int i;
-
- for (i = 0; i < num_formats; i++) {
- fmt = isc->user_formats[i];
- if (fmt->fourcc == fourcc)
- return fmt;
- }
-
- return NULL;
-}
-
static const struct vb2_ops isc_vb2_ops = {
.queue_setup = isc_queue_setup,
.wait_prepare = vb2_ops_wait_prepare,
@@ -497,23 +486,57 @@ static int isc_enum_fmt_vid_cap(struct file *file, void *priv,
{
struct isc_device *isc = video_drvdata(file);
u32 index = f->index;
- u32 i, supported_index;
+ u32 i, supported_index = 0;
+ struct isc_format *fmt;
+
+ /*
+ * If we are not asked a specific mbus_code, we have to report all
+ * the formats that we can output.
+ */
+ if (!f->mbus_code) {
+ if (index >= isc->controller_formats_size)
+ return -EINVAL;
- if (index < isc->controller_formats_size) {
f->pixelformat = isc->controller_formats[index].fourcc;
+
+ return 0;
+ }
+
+ /*
+ * If a specific mbus_code is requested, check if we support
+ * this mbus_code as input for the ISC.
+ * If it's supported, then we report the corresponding pixelformat
+ * as first possible option for the ISC.
+ * E.g. mbus MEDIA_BUS_FMT_YUYV8_2X8 and report
+ * 'YUYV' (YUYV 4:2:2)
+ */
+ fmt = isc_find_format_by_code(isc, f->mbus_code, &i);
+ if (!fmt)
+ return -EINVAL;
+
+ if (!index) {
+ f->pixelformat = fmt->fourcc;
+
return 0;
}
- index -= isc->controller_formats_size;
+ supported_index++;
- supported_index = 0;
+ /* If the index is not raw, we don't have anymore formats to report */
+ if (!ISC_IS_FORMAT_RAW(f->mbus_code))
+ return -EINVAL;
- for (i = 0; i < isc->formats_list_size; i++) {
- if (!ISC_IS_FORMAT_RAW(isc->formats_list[i].mbus_code) ||
- !isc->formats_list[i].sd_support)
+ /*
+ * We are asked for a specific mbus code, which is raw.
+ * We have to search through the formats we can convert to.
+ * We have to skip the raw formats, we cannot convert to raw.
+ * E.g. 'AR12' (16-bit ARGB 4-4-4-4), 'AR15' (16-bit ARGB 1-5-5-5), etc.
+ */
+ for (i = 0; i < isc->controller_formats_size; i++) {
+ if (isc->controller_formats[i].raw)
continue;
- if (supported_index == index) {
- f->pixelformat = isc->formats_list[i].fourcc;
+ if (index == supported_index) {
+ f->pixelformat = isc->controller_formats[i].fourcc;
return 0;
}
supported_index++;
@@ -584,20 +607,30 @@ static int isc_try_validate_formats(struct isc_device *isc)
break;
default:
/* any other different formats are not supported */
+ v4l2_err(&isc->v4l2_dev, "Requested unsupported format.\n");
ret = -EINVAL;
}
v4l2_dbg(1, debug, &isc->v4l2_dev,
"Format validation, requested rgb=%u, yuv=%u, grey=%u, bayer=%u\n",
rgb, yuv, grey, bayer);
- /* we cannot output RAW if we do not receive RAW */
- if ((bayer) && !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code))
+ if (bayer &&
+ !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code)) {
+ v4l2_err(&isc->v4l2_dev, "Cannot output RAW if we do not receive RAW.\n");
return -EINVAL;
+ }
- /* we cannot output GREY if we do not receive RAW/GREY */
if (grey && !ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code) &&
- !ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code))
+ !ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code)) {
+ v4l2_err(&isc->v4l2_dev, "Cannot output GREY if we do not receive RAW/GREY.\n");
return -EINVAL;
+ }
+
+ if ((rgb || bayer || yuv) &&
+ ISC_IS_FORMAT_GREY(isc->try_config.sd_format->mbus_code)) {
+ v4l2_err(&isc->v4l2_dev, "Cannot convert GREY to another format.\n");
+ return -EINVAL;
+ }
return ret;
}
@@ -825,7 +858,7 @@ static void isc_try_fse(struct isc_device *isc,
* If we do not know yet which format the subdev is using, we cannot
* do anything.
*/
- if (!isc->try_config.sd_format)
+ if (!isc->config.sd_format)
return;
fse.code = isc->try_config.sd_format->mbus_code;
@@ -846,180 +879,140 @@ static void isc_try_fse(struct isc_device *isc,
}
}
-static int isc_try_fmt(struct isc_device *isc, struct v4l2_format *f,
- u32 *code)
+static int isc_try_fmt(struct isc_device *isc, struct v4l2_format *f)
{
- int i;
- struct isc_format *sd_fmt = NULL, *direct_fmt = NULL;
struct v4l2_pix_format *pixfmt = &f->fmt.pix;
- struct v4l2_subdev_pad_config pad_cfg = {};
- struct v4l2_subdev_state pad_state = {
- .pads = &pad_cfg
- };
- struct v4l2_subdev_format format = {
- .which = V4L2_SUBDEV_FORMAT_TRY,
- };
- u32 mbus_code;
- int ret;
- bool rlp_dma_direct_dump = false;
+ unsigned int i;
if (f->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
return -EINVAL;
- /* Step 1: find a RAW format that is supported */
- for (i = 0; i < isc->num_user_formats; i++) {
- if (ISC_IS_FORMAT_RAW(isc->user_formats[i]->mbus_code)) {
- sd_fmt = isc->user_formats[i];
+ isc->try_config.fourcc = isc->controller_formats[0].fourcc;
+
+ /* find if the format requested is supported */
+ for (i = 0; i < isc->controller_formats_size; i++)
+ if (isc->controller_formats[i].fourcc == pixfmt->pixelformat) {
+ isc->try_config.fourcc = pixfmt->pixelformat;
break;
}
- }
- /* Step 2: We can continue with this RAW format, or we can look
- * for better: maybe sensor supports directly what we need.
- */
- direct_fmt = find_format_by_fourcc(isc, pixfmt->pixelformat);
-
- /* Step 3: We have both. We decide given the module parameter which
- * one to use.
- */
- if (direct_fmt && sd_fmt && sensor_preferred)
- sd_fmt = direct_fmt;
-
- /* Step 4: we do not have RAW but we have a direct format. Use it. */
- if (direct_fmt && !sd_fmt)
- sd_fmt = direct_fmt;
-
- /* Step 5: if we are using a direct format, we need to package
- * everything as 8 bit data and just dump it
- */
- if (sd_fmt == direct_fmt)
- rlp_dma_direct_dump = true;
-
- /* Step 6: We have no format. This can happen if the userspace
- * requests some weird/invalid format.
- * In this case, default to whatever we have
- */
- if (!sd_fmt && !direct_fmt) {
- sd_fmt = isc->user_formats[isc->num_user_formats - 1];
- v4l2_dbg(1, debug, &isc->v4l2_dev,
- "Sensor not supporting %.4s, using %.4s\n",
- (char *)&pixfmt->pixelformat, (char *)&sd_fmt->fourcc);
- }
-
- if (!sd_fmt) {
- ret = -EINVAL;
- goto isc_try_fmt_err;
- }
-
- /* Step 7: Print out what we decided for debugging */
- v4l2_dbg(1, debug, &isc->v4l2_dev,
- "Preferring to have sensor using format %.4s\n",
- (char *)&sd_fmt->fourcc);
- /* Step 8: at this moment we decided which format the subdev will use */
- isc->try_config.sd_format = sd_fmt;
+ isc_try_configure_rlp_dma(isc, false);
/* Limit to Atmel ISC hardware capabilities */
- if (pixfmt->width > isc->max_width)
- pixfmt->width = isc->max_width;
- if (pixfmt->height > isc->max_height)
- pixfmt->height = isc->max_height;
-
- /*
- * The mbus format is the one the subdev outputs.
- * The pixels will be transferred in this format Sensor -> ISC
- */
- mbus_code = sd_fmt->mbus_code;
-
- /*
- * Validate formats. If the required format is not OK, default to raw.
- */
-
- isc->try_config.fourcc = pixfmt->pixelformat;
-
- if (isc_try_validate_formats(isc)) {
- pixfmt->pixelformat = isc->try_config.fourcc = sd_fmt->fourcc;
- /* Re-try to validate the new format */
- ret = isc_try_validate_formats(isc);
- if (ret)
- goto isc_try_fmt_err;
- }
-
- ret = isc_try_configure_rlp_dma(isc, rlp_dma_direct_dump);
- if (ret)
- goto isc_try_fmt_err;
-
- ret = isc_try_configure_pipeline(isc);
- if (ret)
- goto isc_try_fmt_err;
-
- /* Obtain frame sizes if possible to have crop requirements ready */
- isc_try_fse(isc, &pad_state);
-
- v4l2_fill_mbus_format(&format.format, pixfmt, mbus_code);
- ret = v4l2_subdev_call(isc->current_subdev->sd, pad, set_fmt,
- &pad_state, &format);
- if (ret < 0)
- goto isc_try_fmt_subdev_err;
-
- v4l2_fill_pix_format(pixfmt, &format.format);
+ v4l_bound_align_image(&pixfmt->width, 16, isc->max_width, 0,
+ &pixfmt->height, 16, isc->max_height, 0, 0);
+ /* If we did not find the requested format, we will fallback here */
+ pixfmt->pixelformat = isc->try_config.fourcc;
+ pixfmt->colorspace = V4L2_COLORSPACE_SRGB;
+ pixfmt->field = V4L2_FIELD_NONE;
- /* Limit to Atmel ISC hardware capabilities */
- if (pixfmt->width > isc->max_width)
- pixfmt->width = isc->max_width;
- if (pixfmt->height > isc->max_height)
- pixfmt->height = isc->max_height;
- pixfmt->field = V4L2_FIELD_NONE;
pixfmt->bytesperline = (pixfmt->width * isc->try_config.bpp_v4l2) >> 3;
pixfmt->sizeimage = ((pixfmt->width * isc->try_config.bpp) >> 3) *
pixfmt->height;
- if (code)
- *code = mbus_code;
+ isc->try_fmt = *f;
return 0;
+}
-isc_try_fmt_err:
- v4l2_err(&isc->v4l2_dev, "Could not find any possible format for a working pipeline\n");
-isc_try_fmt_subdev_err:
- memset(&isc->try_config, 0, sizeof(isc->try_config));
+static int isc_set_fmt(struct isc_device *isc, struct v4l2_format *f)
+{
+ isc_try_fmt(isc, f);
- return ret;
+ /* make the try configuration active */
+ isc->config = isc->try_config;
+ isc->fmt = isc->try_fmt;
+
+ v4l2_dbg(1, debug, &isc->v4l2_dev, "ISC set_fmt to %.4s @%dx%d\n",
+ (char *)&f->fmt.pix.pixelformat,
+ f->fmt.pix.width, f->fmt.pix.height);
+
+ return 0;
}
-static int isc_set_fmt(struct isc_device *isc, struct v4l2_format *f)
+static int isc_validate(struct isc_device *isc)
{
+ int ret;
+ int i;
+ struct isc_format *sd_fmt = NULL;
+ struct v4l2_pix_format *pixfmt = &isc->fmt.fmt.pix;
struct v4l2_subdev_format format = {
.which = V4L2_SUBDEV_FORMAT_ACTIVE,
+ .pad = isc->remote_pad,
+ };
+ struct v4l2_subdev_pad_config pad_cfg = {};
+ struct v4l2_subdev_state pad_state = {
+ .pads = &pad_cfg,
};
- u32 mbus_code = 0;
- int ret;
- ret = isc_try_fmt(isc, f, &mbus_code);
+ /* Get current format from subdev */
+ ret = v4l2_subdev_call(isc->current_subdev->sd, pad, get_fmt, NULL,
+ &format);
if (ret)
return ret;
- v4l2_fill_mbus_format(&format.format, &f->fmt.pix, mbus_code);
- ret = v4l2_subdev_call(isc->current_subdev->sd, pad,
- set_fmt, NULL, &format);
- if (ret < 0)
- return ret;
+ /* Identify the subdev's format configuration */
+ for (i = 0; i < isc->formats_list_size; i++)
+ if (isc->formats_list[i].mbus_code == format.format.code) {
+ sd_fmt = &isc->formats_list[i];
+ break;
+ }
+
+ /* Check if the format is not supported */
+ if (!sd_fmt) {
+ v4l2_err(&isc->v4l2_dev,
+ "Current subdevice is streaming a media bus code that is not supported 0x%x\n",
+ format.format.code);
+ return -EPIPE;
+ }
+
+ /* At this moment we know which format the subdev will use */
+ isc->try_config.sd_format = sd_fmt;
+
+ /* If the sensor is not RAW, we can only do a direct dump */
+ if (!ISC_IS_FORMAT_RAW(isc->try_config.sd_format->mbus_code))
+ isc_try_configure_rlp_dma(isc, true);
/* Limit to Atmel ISC hardware capabilities */
- if (f->fmt.pix.width > isc->max_width)
- f->fmt.pix.width = isc->max_width;
- if (f->fmt.pix.height > isc->max_height)
- f->fmt.pix.height = isc->max_height;
+ v4l_bound_align_image(&format.format.width, 16, isc->max_width, 0,
+ &format.format.height, 16, isc->max_height, 0, 0);
- isc->fmt = *f;
+ /* Check if the frame size is the same. Otherwise we may overflow */
+ if (pixfmt->height != format.format.height ||
+ pixfmt->width != format.format.width) {
+ v4l2_err(&isc->v4l2_dev,
+ "ISC not configured with the proper frame size: %dx%d\n",
+ format.format.width, format.format.height);
+ return -EPIPE;
+ }
+ v4l2_dbg(1, debug, &isc->v4l2_dev,
+ "Identified subdev using format %.4s with %dx%d %d bpp\n",
+ (char *)&sd_fmt->fourcc, pixfmt->width, pixfmt->height,
+ isc->try_config.bpp);
+
+ /* Reset and restart AWB if the subdevice changed the format */
if (isc->try_config.sd_format && isc->config.sd_format &&
isc->try_config.sd_format != isc->config.sd_format) {
isc->ctrls.hist_stat = HIST_INIT;
isc_reset_awb_ctrls(isc);
isc_update_v4l2_ctrls(isc);
}
- /* make the try configuration active */
+
+ /* Validate formats */
+ ret = isc_try_validate_formats(isc);
+ if (ret)
+ return ret;
+
+ /* Obtain frame sizes if possible to have crop requirements ready */
+ isc_try_fse(isc, &pad_state);
+
+ /* Configure ISC pipeline for the config */
+ ret = isc_try_configure_pipeline(isc);
+ if (ret)
+ return ret;
+
isc->config = isc->try_config;
v4l2_dbg(1, debug, &isc->v4l2_dev, "New ISC configuration in place\n");
@@ -1043,7 +1036,7 @@ static int isc_try_fmt_vid_cap(struct file *file, void *priv,
{
struct isc_device *isc = video_drvdata(file);
- return isc_try_fmt(isc, f, NULL);
+ return isc_try_fmt(isc, f);
}
static int isc_enum_input(struct file *file, void *priv,
@@ -1098,10 +1091,6 @@ static int isc_enum_framesizes(struct file *file, void *fh,
if (fsize->index)
return -EINVAL;
- for (i = 0; i < isc->num_user_formats; i++)
- if (isc->user_formats[i]->fourcc == fsize->pixel_format)
- ret = 0;
-
for (i = 0; i < isc->controller_formats_size; i++)
if (isc->controller_formats[i].fourcc == fsize->pixel_format)
ret = 0;
@@ -1782,52 +1771,6 @@ struct isc_format *isc_find_format_by_code(struct isc_device *isc,
}
EXPORT_SYMBOL_GPL(isc_find_format_by_code);
-static int isc_formats_init(struct isc_device *isc)
-{
- struct isc_format *fmt;
- struct v4l2_subdev *subdev = isc->current_subdev->sd;
- unsigned int num_fmts, i, j;
- u32 list_size = isc->formats_list_size;
- struct v4l2_subdev_mbus_code_enum mbus_code = {
- .which = V4L2_SUBDEV_FORMAT_ACTIVE,
- };
-
- num_fmts = 0;
- while (!v4l2_subdev_call(subdev, pad, enum_mbus_code,
- NULL, &mbus_code)) {
- mbus_code.index++;
-
- fmt = isc_find_format_by_code(isc, mbus_code.code, &i);
- if (!fmt) {
- v4l2_warn(&isc->v4l2_dev, "Mbus code %x not supported\n",
- mbus_code.code);
- continue;
- }
-
- fmt->sd_support = true;
- num_fmts++;
- }
-
- if (!num_fmts)
- return -ENXIO;
-
- isc->num_user_formats = num_fmts;
- isc->user_formats = devm_kcalloc(isc->dev,
- num_fmts, sizeof(*isc->user_formats),
- GFP_KERNEL);
- if (!isc->user_formats)
- return -ENOMEM;
-
- fmt = &isc->formats_list[0];
- for (i = 0, j = 0; i < list_size; i++) {
- if (fmt->sd_support)
- isc->user_formats[j++] = fmt;
- fmt++;
- }
-
- return 0;
-}
-
static int isc_set_default_fmt(struct isc_device *isc)
{
struct v4l2_format f = {
@@ -1836,12 +1779,12 @@ static int isc_set_default_fmt(struct isc_device *isc)
.width = VGA_WIDTH,
.height = VGA_HEIGHT,
.field = V4L2_FIELD_NONE,
- .pixelformat = isc->user_formats[0]->fourcc,
+ .pixelformat = isc->controller_formats[0].fourcc,
},
};
int ret;
- ret = isc_try_fmt(isc, &f, NULL);
+ ret = isc_try_fmt(isc, &f);
if (ret)
return ret;
@@ -1896,13 +1839,6 @@ static int isc_async_complete(struct v4l2_async_notifier *notifier)
spin_lock_init(&isc->dma_queue_lock);
spin_lock_init(&isc->awb_lock);
- ret = isc_formats_init(isc);
- if (ret < 0) {
- v4l2_err(&isc->v4l2_dev,
- "Init format failed: %d\n", ret);
- goto isc_async_complete_err;
- }
-
ret = isc_set_default_fmt(isc);
if (ret) {
v4l2_err(&isc->v4l2_dev, "Could not set default format\n");
@@ -2016,6 +1952,24 @@ int isc_pipeline_init(struct isc_device *isc)
}
EXPORT_SYMBOL_GPL(isc_pipeline_init);
+int isc_link_validate(struct media_link *link)
+{
+ struct video_device *vdev =
+ media_entity_to_video_device(link->sink->entity);
+ struct isc_device *isc = video_get_drvdata(vdev);
+ int ret;
+
+ ret = v4l2_subdev_link_validate(link);
+ if (ret)
+ return ret;
+
+ return isc_validate(isc);
+}
+
+static const struct media_entity_operations isc_entity_operations = {
+ .link_validate = isc_link_validate,
+};
+
int isc_mc_init(struct isc_device *isc, u32 ver)
{
const struct of_device_id *match;
@@ -2023,6 +1977,8 @@ int isc_mc_init(struct isc_device *isc, u32 ver)
isc->video_dev.entity.function = MEDIA_ENT_F_IO_V4L;
isc->video_dev.entity.flags = MEDIA_ENT_FL_DEFAULT;
+ isc->video_dev.entity.ops = &isc_entity_operations;
+
isc->pads[ISC_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
ret = media_entity_pads_init(&isc->video_dev.entity, ISC_PADS_NUM,
diff --git a/drivers/media/platform/atmel/atmel-isc-scaler.c b/drivers/media/platform/atmel/atmel-isc-scaler.c
index a1ca4633787c..2b0621297dfe 100644
--- a/drivers/media/platform/atmel/atmel-isc-scaler.c
+++ b/drivers/media/platform/atmel/atmel-isc-scaler.c
@@ -173,6 +173,10 @@ static const struct v4l2_subdev_pad_ops isc_scaler_pad_ops = {
.init_cfg = isc_scaler_init_cfg,
};
+static const struct media_entity_operations isc_scaler_entity_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+};
+
static const struct v4l2_subdev_ops xisc_scaler_subdev_ops = {
.pad = &isc_scaler_pad_ops,
};
@@ -190,6 +194,7 @@ int isc_scaler_init(struct isc_device *isc)
isc->scaler_sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
isc->scaler_sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_SCALER;
+ isc->scaler_sd.entity.ops = &isc_scaler_entity_ops;
isc->scaler_pads[ISC_SCALER_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
isc->scaler_pads[ISC_SCALER_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
diff --git a/drivers/media/platform/atmel/atmel-isc.h b/drivers/media/platform/atmel/atmel-isc.h
index f98f25a55e73..5b0100c8c245 100644
--- a/drivers/media/platform/atmel/atmel-isc.h
+++ b/drivers/media/platform/atmel/atmel-isc.h
@@ -63,15 +63,16 @@ struct isc_subdev_entity {
* @cfa_baycfg: If this format is RAW BAYER, indicate the type of bayer.
this is either BGBG, RGRG, etc.
* @pfe_cfg0_bps: Number of hardware data lines connected to the ISC
+ * @raw: If the format is raw bayer.
*/
struct isc_format {
u32 fourcc;
u32 mbus_code;
u32 cfa_baycfg;
-
- bool sd_support;
u32 pfe_cfg0_bps;
+
+ bool raw;
};
/* Pipeline bitmap */
@@ -216,8 +217,7 @@ enum isc_scaler_pads {
* @comp: completion reference that signals frame completion
*
* @fmt: current v42l format
- * @user_formats: list of formats that are supported and agreed with sd
- * @num_user_formats: how many formats are in user_formats
+ * @try_fmt: current v4l2 try format
*
* @config: current ISC format configuration
* @try_config: the current ISC try format , not yet activated
@@ -272,6 +272,7 @@ enum isc_scaler_pads {
* @formats_list_size: size of formats_list array
* @pads: media controller pads for isc video entity
* @mdev: media device that is registered by the isc
+ * @mpipe: media device pipeline used by the isc
* @remote_pad: remote pad on the connected subdevice
* @scaler_sd: subdevice for the scaler that isc registers
* @scaler_pads: media controller pads for the scaler subdevice
@@ -298,8 +299,7 @@ struct isc_device {
struct completion comp;
struct v4l2_format fmt;
- struct isc_format **user_formats;
- unsigned int num_user_formats;
+ struct v4l2_format try_fmt;
struct fmt_config config;
struct fmt_config try_config;
@@ -369,6 +369,7 @@ struct isc_device {
struct {
struct media_pad pads[ISC_PADS_NUM];
struct media_device mdev;
+ struct media_pipeline mpipe;
u32 remote_pad;
};
diff --git a/drivers/media/platform/atmel/atmel-sama5d2-isc.c b/drivers/media/platform/atmel/atmel-sama5d2-isc.c
index d96ee3373889..2a651e237193 100644
--- a/drivers/media/platform/atmel/atmel-sama5d2-isc.c
+++ b/drivers/media/platform/atmel/atmel-sama5d2-isc.c
@@ -80,20 +80,40 @@ static const struct isc_format sama5d2_controller_formats[] = {
.fourcc = V4L2_PIX_FMT_Y10,
}, {
.fourcc = V4L2_PIX_FMT_SBGGR8,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SGBRG8,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SGRBG8,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SRGGB8,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SBGGR10,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SGBRG10,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SGRBG10,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SRGGB10,
+ .raw = true,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SBGGR12,
+ .raw = true,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG12,
+ .raw = true,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG12,
+ .raw = true,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB12,
+ .raw = true,
},
};
diff --git a/drivers/media/platform/atmel/atmel-sama7g5-isc.c b/drivers/media/platform/atmel/atmel-sama7g5-isc.c
index e07ae188c15f..a0d60cfdba7b 100644
--- a/drivers/media/platform/atmel/atmel-sama7g5-isc.c
+++ b/drivers/media/platform/atmel/atmel-sama7g5-isc.c
@@ -89,20 +89,40 @@ static const struct isc_format sama7g5_controller_formats[] = {
.fourcc = V4L2_PIX_FMT_Y16,
}, {
.fourcc = V4L2_PIX_FMT_SBGGR8,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SGBRG8,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SGRBG8,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SRGGB8,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SBGGR10,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SGBRG10,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SGRBG10,
+ .raw = true,
}, {
.fourcc = V4L2_PIX_FMT_SRGGB10,
+ .raw = true,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SBGGR12,
+ .raw = true,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG12,
+ .raw = true,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG12,
+ .raw = true,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB12,
+ .raw = true,
},
};
--
2.25.1
Add drivers for the atmel video capture pipeline: atmel isc, xisc and
microchip csi2dc.
Signed-off-by: Eugen Hristev <[email protected]>
---
arch/arm/configs/multi_v7_defconfig | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index 8863fa969ede..b768abad8df0 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -639,7 +639,10 @@ CONFIG_VIDEO_S5P_MIPI_CSIS=m
CONFIG_VIDEO_EXYNOS_FIMC_LITE=m
CONFIG_VIDEO_EXYNOS4_FIMC_IS=m
CONFIG_VIDEO_RCAR_VIN=m
+CONFIG_VIDEO_ATMEL_ISC=m
+CONFIG_VIDEO_ATMEL_XISC=m
CONFIG_VIDEO_ATMEL_ISI=m
+CONFIG_VIDEO_MICROCHIP_CSI2DC=m
CONFIG_V4L_MEM2MEM_DRIVERS=y
CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
--
2.25.1
Compact the list array to be more readable.
No other changes, only cosmetic.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
.../media/platform/atmel/atmel-sama5d2-isc.c | 51 ++++++----------
.../media/platform/atmel/atmel-sama7g5-isc.c | 60 +++++++------------
2 files changed, 37 insertions(+), 74 deletions(-)
diff --git a/drivers/media/platform/atmel/atmel-sama5d2-isc.c b/drivers/media/platform/atmel/atmel-sama5d2-isc.c
index 025c3e8a7e95..d96ee3373889 100644
--- a/drivers/media/platform/atmel/atmel-sama5d2-isc.c
+++ b/drivers/media/platform/atmel/atmel-sama5d2-isc.c
@@ -60,56 +60,39 @@
static const struct isc_format sama5d2_controller_formats[] = {
{
.fourcc = V4L2_PIX_FMT_ARGB444,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_ARGB555,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_RGB565,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_ABGR32,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_XBGR32,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_YUV420,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_YUYV,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_YUV422P,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_GREY,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_Y10,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SBGGR8,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SGBRG8,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SGRBG8,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SRGGB8,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SBGGR10,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SGBRG10,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SGRBG10,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SRGGB10,
},
};
diff --git a/drivers/media/platform/atmel/atmel-sama7g5-isc.c b/drivers/media/platform/atmel/atmel-sama7g5-isc.c
index 9dc75eed0098..e07ae188c15f 100644
--- a/drivers/media/platform/atmel/atmel-sama7g5-isc.c
+++ b/drivers/media/platform/atmel/atmel-sama7g5-isc.c
@@ -63,65 +63,45 @@
static const struct isc_format sama7g5_controller_formats[] = {
{
.fourcc = V4L2_PIX_FMT_ARGB444,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_ARGB555,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_RGB565,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_ABGR32,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_XBGR32,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_YUV420,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_UYVY,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_VYUY,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_YUYV,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_YUV422P,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_GREY,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_Y10,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_Y16,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SBGGR8,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SGBRG8,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SGRBG8,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SRGGB8,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SBGGR10,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SGBRG10,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SGRBG10,
- },
- {
+ }, {
.fourcc = V4L2_PIX_FMT_SRGGB10,
},
};
--
2.25.1
Add node for the XISC (eXtended Image Sensor Controller) and CSI2DC
(csi2 demux controller).
These nodes represent the top level of the video capture hardware pipeline
and are directly connected in hardware.
Signed-off-by: Eugen Hristev <[email protected]>
---
arch/arm/boot/dts/sama7g5.dtsi | 49 ++++++++++++++++++++++++++++++++++
1 file changed, 49 insertions(+)
diff --git a/arch/arm/boot/dts/sama7g5.dtsi b/arch/arm/boot/dts/sama7g5.dtsi
index eddcfbf4d223..de43f854ce47 100644
--- a/arch/arm/boot/dts/sama7g5.dtsi
+++ b/arch/arm/boot/dts/sama7g5.dtsi
@@ -266,6 +266,55 @@ sdmmc2: mmc@e120c000 {
status = "disabled";
};
+ csi2dc: csi2dc@e1404000 {
+ compatible = "microchip,sama7g5-csi2dc";
+ reg = <0xe1404000 0x500>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&xisc>;
+ clock-names = "pclk", "scck";
+ assigned-clocks = <&xisc>;
+ assigned-clock-rates = <266000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ csi2dc_in: endpoint {
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ csi2dc_out: endpoint {
+ bus-width = <14>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ remote-endpoint = <&xisc_in>;
+ };
+ };
+ };
+ };
+
+ xisc: xisc@e1408000 {
+ compatible = "microchip,sama7g5-isc";
+ reg = <0xe1408000 0x2000>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 56>;
+ clock-names = "hclock";
+ #clock-cells = <0>;
+ clock-output-names = "isc-mck";
+
+ port {
+ xisc_in: endpoint {
+ bus-type = <5>; /* Parallel */
+ bus-width = <14>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ remote-endpoint = <&csi2dc_out>;
+ };
+ };
+ };
+
pwm: pwm@e1604000 {
compatible = "microchip,sama7g5-pwm", "atmel,sama5d2-pwm";
reg = <0xe1604000 0x4000>;
--
2.25.1
While this does not happen in production, this check should be done
versus the mask, as checking with the YCYC value may not include
some bits that may be set.
Is it correct and safe to check the whole mask.
Fixes: 123aaf816b95 ("media: atmel: atmel-sama5d2-isc: fix YUYV format")
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
drivers/media/platform/atmel/atmel-sama5d2-isc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/media/platform/atmel/atmel-sama5d2-isc.c b/drivers/media/platform/atmel/atmel-sama5d2-isc.c
index c244682ea22f..025c3e8a7e95 100644
--- a/drivers/media/platform/atmel/atmel-sama5d2-isc.c
+++ b/drivers/media/platform/atmel/atmel-sama5d2-isc.c
@@ -291,7 +291,7 @@ static void isc_sama5d2_config_rlp(struct isc_device *isc)
* Thus, if the YCYC mode is selected, replace it with the
* sama5d2-compliant mode which is YYCC .
*/
- if ((rlp_mode & ISC_RLP_CFG_MODE_YCYC) == ISC_RLP_CFG_MODE_YCYC) {
+ if ((rlp_mode & ISC_RLP_CFG_MODE_MASK) == ISC_RLP_CFG_MODE_YCYC) {
rlp_mode &= ~ISC_RLP_CFG_MODE_MASK;
rlp_mode |= ISC_RLP_CFG_MODE_YYCC;
}
--
2.25.1
The AWB workqueue runs in a kernel thread and needs to be synchronized
w.r.t. the streaming status.
It is possible that streaming is stopped while the AWB workq is running.
In this case it is likely that the check for vb2_start_streaming_called is done
at one point in time, but the AWB computations are done later, including a call
to isc_update_profile, which requires streaming to be started.
Thus , isc_update_profile will fail if during this operation sequence the
streaming was stopped.
To solve this issue, a mutex is added, that will serialize the awb work and
streaming stopping, with the mention that either streaming is stopped
completely including termination of the last frame is done, and after that
the AWB work can check stream status and stop; either first AWB work is
completed and after that the streaming can stop correctly.
The awb spin lock cannot be used since this spinlock is taken in the same
context and using it in the stop streaming will result in a recursion BUG.
Signed-off-by: Eugen Hristev <[email protected]>
Reviewed-by: Jacopo Mondi <[email protected]>
---
drivers/media/platform/atmel/atmel-isc-base.c | 29 ++++++++++++++++---
drivers/media/platform/atmel/atmel-isc.h | 2 ++
2 files changed, 27 insertions(+), 4 deletions(-)
diff --git a/drivers/media/platform/atmel/atmel-isc-base.c b/drivers/media/platform/atmel/atmel-isc-base.c
index 448bf281c61a..ee1dda6707a0 100644
--- a/drivers/media/platform/atmel/atmel-isc-base.c
+++ b/drivers/media/platform/atmel/atmel-isc-base.c
@@ -401,6 +401,7 @@ static void isc_stop_streaming(struct vb2_queue *vq)
struct isc_buffer *buf;
int ret;
+ mutex_lock(&isc->awb_mutex);
v4l2_ctrl_activate(isc->do_wb_ctrl, false);
isc->stop = true;
@@ -410,6 +411,8 @@ static void isc_stop_streaming(struct vb2_queue *vq)
v4l2_err(&isc->v4l2_dev,
"Timeout waiting for end of the capture\n");
+ mutex_unlock(&isc->awb_mutex);
+
/* Disable DMA interrupt */
regmap_write(isc->regmap, ISC_INTDIS, ISC_INT_DDONE);
@@ -1397,10 +1400,6 @@ static void isc_awb_work(struct work_struct *w)
u32 min, max;
int ret;
- /* streaming is not active anymore */
- if (isc->stop)
- return;
-
if (ctrls->hist_stat != HIST_ENABLED)
return;
@@ -1455,7 +1454,24 @@ static void isc_awb_work(struct work_struct *w)
}
regmap_write(regmap, ISC_HIS_CFG + isc->offsets.his,
hist_id | baysel | ISC_HIS_CFG_RAR);
+
+ /*
+ * We have to make sure the streaming has not stopped meanwhile.
+ * ISC requires a frame to clock the internal profile update.
+ * To avoid issues, lock the sequence with a mutex
+ */
+ mutex_lock(&isc->awb_mutex);
+
+ /* streaming is not active anymore */
+ if (isc->stop) {
+ mutex_unlock(&isc->awb_mutex);
+ return;
+ };
+
isc_update_profile(isc);
+
+ mutex_unlock(&isc->awb_mutex);
+
/* if awb has been disabled, we don't need to start another histogram */
if (ctrls->awb)
regmap_write(regmap, ISC_CTRLEN, ISC_CTRL_HISREQ);
@@ -1548,6 +1564,7 @@ static int isc_s_awb_ctrl(struct v4l2_ctrl *ctrl)
*/
v4l2_ctrl_activate(isc->do_wb_ctrl, false);
}
+ mutex_unlock(&isc->awb_mutex);
/* if we have autowhitebalance on, start histogram procedure */
if (ctrls->awb == ISC_WB_AUTO &&
@@ -1740,6 +1757,7 @@ static void isc_async_unbind(struct v4l2_async_notifier *notifier,
{
struct isc_device *isc = container_of(notifier->v4l2_dev,
struct isc_device, v4l2_dev);
+ mutex_destroy(&isc->awb_mutex);
cancel_work_sync(&isc->awb_work);
video_unregister_device(&isc->video_dev);
v4l2_ctrl_handler_free(&isc->ctrls.handler);
@@ -1850,6 +1868,8 @@ static int isc_async_complete(struct v4l2_async_notifier *notifier)
isc->current_subdev = container_of(notifier,
struct isc_subdev_entity, notifier);
mutex_init(&isc->lock);
+ mutex_init(&isc->awb_mutex);
+
init_completion(&isc->comp);
/* Initialize videobuf2 queue */
@@ -1930,6 +1950,7 @@ static int isc_async_complete(struct v4l2_async_notifier *notifier)
video_unregister_device(vdev);
isc_async_complete_err:
+ mutex_destroy(&isc->awb_mutex);
mutex_destroy(&isc->lock);
return ret;
}
diff --git a/drivers/media/platform/atmel/atmel-isc.h b/drivers/media/platform/atmel/atmel-isc.h
index 9cc69c3ae26d..f98f25a55e73 100644
--- a/drivers/media/platform/atmel/atmel-isc.h
+++ b/drivers/media/platform/atmel/atmel-isc.h
@@ -229,6 +229,7 @@ enum isc_scaler_pads {
*
* @lock: lock for serializing userspace file operations
* with ISC operations
+ * @awb_mutex: serialize access to streaming status from awb work queue
* @awb_lock: lock for serializing awb work queue operations
* with DMA/buffer operations
*
@@ -307,6 +308,7 @@ struct isc_device {
struct work_struct awb_work;
struct mutex lock;
+ struct mutex awb_mutex;
spinlock_t awb_lock;
struct regmap_field *pipeline[ISC_PIPE_LINE_NODE_NUM];
--
2.25.1
The Microchip XISC supports a bus width of 14 bits.
Add it to the supported bus widths.
Signed-off-by: Eugen Hristev <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/media/microchip,xisc.yaml | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/media/microchip,xisc.yaml b/Documentation/devicetree/bindings/media/microchip,xisc.yaml
index 086e1430af4f..3be8f64c3e21 100644
--- a/Documentation/devicetree/bindings/media/microchip,xisc.yaml
+++ b/Documentation/devicetree/bindings/media/microchip,xisc.yaml
@@ -67,7 +67,7 @@ properties:
remote-endpoint: true
bus-width:
- enum: [8, 9, 10, 11, 12]
+ enum: [8, 9, 10, 11, 12, 14]
default: 12
hsync-active:
--
2.25.1