Create new dts file specific for Qdrive board based on sa8540p chipset.
Introduce common dtsi file sa8295p-adp.dtsi, to be included for adp and
Qdrive board.
Signed-off-by: Parikshit Pareek <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 378 +----------------
arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi | 385 ++++++++++++++++++
arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts | 15 +
4 files changed, 403 insertions(+), 376 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 9e2a13d75f9d..fa0abcf7660b 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sa8540p-adp-ride.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb
diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
index 9398f0349944..adb6637117bc 100644
--- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
+++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
@@ -2,388 +2,14 @@
/*
* Copyright (c) 2021, The Linux Foundation. All rights reserved.
* Copyright (c) 2022, Linaro Limited
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
*/
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-#include <dt-bindings/spmi/spmi.h>
-
-#include "sa8540p.dtsi"
+#include "sa8295p-adp.dtsi"
/ {
model = "Qualcomm SA8295P ADP";
compatible = "qcom,sa8295p-adp", "qcom,sa8540p";
-
- aliases {
- serial0 = &qup2_uart17;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&apps_rsc {
- pmm8540-a-regulators {
- compatible = "qcom,pm8150-rpmh-regulators";
- qcom,pmic-id = "a";
-
- vreg_l3a: ldo3 {
- regulator-name = "vreg_l3a";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1208000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l5a: ldo5 {
- regulator-name = "vreg_l5a";
- regulator-min-microvolt = <912000>;
- regulator-max-microvolt = <912000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l7a: ldo7 {
- regulator-name = "vreg_l7a";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l13a: ldo13 {
- regulator-name = "vreg_l13a";
- regulator-min-microvolt = <3072000>;
- regulator-max-microvolt = <3072000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
- };
-
- pmm8540-c-regulators {
- compatible = "qcom,pm8150-rpmh-regulators";
- qcom,pmic-id = "c";
-
- vreg_l1c: ldo1 {
- regulator-name = "vreg_l1c";
- regulator-min-microvolt = <912000>;
- regulator-max-microvolt = <912000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l2c: ldo2 {
- regulator-name = "vreg_l2c";
- regulator-min-microvolt = <3072000>;
- regulator-max-microvolt = <3072000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l3c: ldo3 {
- regulator-name = "vreg_l3c";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l4c: ldo4 {
- regulator-name = "vreg_l4c";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1208000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l6c: ldo6 {
- regulator-name = "vreg_l6c";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l7c: ldo7 {
- regulator-name = "vreg_l7c";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l10c: ldo10 {
- regulator-name = "vreg_l10c";
- regulator-min-microvolt = <2504000>;
- regulator-max-microvolt = <2504000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l17c: ldo17 {
- regulator-name = "vreg_l17c";
- regulator-min-microvolt = <2504000>;
- regulator-max-microvolt = <2504000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
- };
-
- pmm8540-g-regulators {
- compatible = "qcom,pm8150-rpmh-regulators";
- qcom,pmic-id = "g";
-
- vreg_l3g: ldo3 {
- regulator-name = "vreg_l3g";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l7g: ldo7 {
- regulator-name = "vreg_l7g";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
-
- vreg_l8g: ldo8 {
- regulator-name = "vreg_l8g";
- regulator-min-microvolt = <880000>;
- regulator-max-microvolt = <880000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- };
- };
-};
-
-&qup2 {
- status = "okay";
-};
-
-&qup2_uart17 {
- compatible = "qcom,geni-debug-uart";
- status = "okay";
-};
-
-&remoteproc_adsp {
- firmware-name = "qcom/sa8540p/adsp.mbn";
- status = "okay";
-};
-
-&remoteproc_nsp0 {
- firmware-name = "qcom/sa8540p/cdsp.mbn";
- status = "okay";
-};
-
-&remoteproc_nsp1 {
- firmware-name = "qcom/sa8540p/cdsp1.mbn";
- status = "okay";
-};
-
-&spmi_bus {
- pm8450a: pmic@0 {
- compatible = "qcom,pm8150", "qcom,spmi-pmic";
- reg = <0x0 SPMI_USID>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pm8450a_gpios: gpio@c000 {
- compatible = "qcom,pm8150-gpio";
- reg = <0xc000>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
- };
-
- pm8450c: pmic@4 {
- compatible = "qcom,pm8150", "qcom,spmi-pmic";
- reg = <0x4 SPMI_USID>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pm8450c_gpios: gpio@c000 {
- compatible = "qcom,pm8150-gpio";
- reg = <0xc000>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
- };
-
- pm8450e: pmic@8 {
- compatible = "qcom,pm8150", "qcom,spmi-pmic";
- reg = <0x8 SPMI_USID>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pm8450e_gpios: gpio@c000 {
- compatible = "qcom,pm8150-gpio";
- reg = <0xc000>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
- };
-
- pm8450g: pmic@c {
- compatible = "qcom,pm8150", "qcom,spmi-pmic";
- reg = <0xc SPMI_USID>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- pm8450g_gpios: gpio@c000 {
- compatible = "qcom,pm8150-gpio";
- reg = <0xc000>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
- };
-};
-
-&ufs_mem_hc {
- reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
-
- vcc-supply = <&vreg_l17c>;
- vcc-max-microamp = <800000>;
- vccq-supply = <&vreg_l6c>;
- vccq-max-microamp = <900000>;
-
- status = "okay";
-};
-
-&ufs_mem_phy {
- vdda-phy-supply = <&vreg_l8g>;
- vdda-pll-supply = <&vreg_l3g>;
-
- status = "okay";
};
-
-&ufs_card_hc {
- reset-gpios = <&tlmm 229 GPIO_ACTIVE_LOW>;
-
- vcc-supply = <&vreg_l10c>;
- vcc-max-microamp = <800000>;
- vccq-supply = <&vreg_l3c>;
- vccq-max-microamp = <900000>;
-
- status = "okay";
-};
-
-&ufs_card_phy {
- vdda-phy-supply = <&vreg_l8g>;
- vdda-pll-supply = <&vreg_l3g>;
-
- status = "okay";
-};
-
-&usb_0 {
- status = "okay";
-};
-
-&usb_0_dwc3 {
- /* TODO: Define USB-C connector properly */
- dr_mode = "peripheral";
-};
-
-&usb_0_hsphy {
- vdda-pll-supply = <&vreg_l5a>;
- vdda18-supply = <&vreg_l7a>;
- vdda33-supply = <&vreg_l13a>;
-
- status = "okay";
-};
-
-&usb_0_qmpphy {
- vdda-phy-supply = <&vreg_l3a>;
- vdda-pll-supply = <&vreg_l5a>;
-
- status = "okay";
-};
-
-&usb_1 {
- status = "okay";
-};
-
-&usb_1_dwc3 {
- /* TODO: Define USB-C connector properly */
- dr_mode = "host";
-};
-
-&usb_1_hsphy {
- vdda-pll-supply = <&vreg_l1c>;
- vdda18-supply = <&vreg_l7c>;
- vdda33-supply = <&vreg_l2c>;
-
- status = "okay";
-};
-
-&usb_1_qmpphy {
- vdda-phy-supply = <&vreg_l4c>;
- vdda-pll-supply = <&vreg_l1c>;
-
- status = "okay";
-};
-
-&usb_2_hsphy0 {
- vdda-pll-supply = <&vreg_l5a>;
- vdda18-supply = <&vreg_l7g>;
- vdda33-supply = <&vreg_l13a>;
-
- status = "okay";
-};
-
-&usb_2_hsphy1 {
- vdda-pll-supply = <&vreg_l5a>;
- vdda18-supply = <&vreg_l7g>;
- vdda33-supply = <&vreg_l13a>;
-
- status = "okay";
-};
-
-&usb_2_hsphy2 {
- vdda-pll-supply = <&vreg_l5a>;
- vdda18-supply = <&vreg_l7g>;
- vdda33-supply = <&vreg_l13a>;
-
- status = "okay";
-};
-
-&usb_2_hsphy3 {
- vdda-pll-supply = <&vreg_l5a>;
- vdda18-supply = <&vreg_l7g>;
- vdda33-supply = <&vreg_l13a>;
-
- status = "okay";
-};
-
-&usb_2_qmpphy0 {
- vdda-phy-supply = <&vreg_l3a>;
- vdda-pll-supply = <&vreg_l5a>;
-
- status = "okay";
-};
-
-&usb_2_qmpphy1 {
- vdda-phy-supply = <&vreg_l3a>;
- vdda-pll-supply = <&vreg_l5a>;
-
- status = "okay";
-};
-
-&xo_board_clk {
- clock-frequency = <38400000>;
-};
-
-/* PINCTRL */
diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi b/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
new file mode 100644
index 000000000000..75ef77b7cac1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
@@ -0,0 +1,385 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/spmi/spmi.h>
+
+#include "sa8540p.dtsi"
+
+/ {
+ aliases {
+ serial0 = &qup2_uart17;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&apps_rsc {
+ pmm8540-a-regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1208000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l13a: ldo13 {
+ regulator-name = "vreg_l13a";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+
+ pmm8540-c-regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l2c: ldo2 {
+ regulator-name = "vreg_l2c";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l3c: ldo3 {
+ regulator-name = "vreg_l3c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l4c: ldo4 {
+ regulator-name = "vreg_l4c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1208000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l10c: ldo10 {
+ regulator-name = "vreg_l10c";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l17c: ldo17 {
+ regulator-name = "vreg_l17c";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+
+ pmm8540-g-regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "g";
+
+ vreg_l3g: ldo3 {
+ regulator-name = "vreg_l3g";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7g: ldo7 {
+ regulator-name = "vreg_l7g";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l8g: ldo8 {
+ regulator-name = "vreg_l8g";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+ };
+};
+
+&qup2 {
+ status = "okay";
+};
+
+&qup2_uart17 {
+ compatible = "qcom,geni-debug-uart";
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sa8540p/adsp.mbn";
+ status = "okay";
+};
+
+&remoteproc_nsp0 {
+ firmware-name = "qcom/sa8540p/cdsp.mbn";
+ status = "okay";
+};
+
+&remoteproc_nsp1 {
+ firmware-name = "qcom/sa8540p/cdsp1.mbn";
+ status = "okay";
+};
+
+&spmi_bus {
+ pm8450a: pmic@0 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450a_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450c: pmic@4 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450c_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450e: pmic@8 {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0x8 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450e_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8450g: pmic@c {
+ compatible = "qcom,pm8150", "qcom,spmi-pmic";
+ reg = <0xc SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8450g_gpios: gpio@c000 {
+ compatible = "qcom,pm8150-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l17c>;
+ vcc-max-microamp = <800000>;
+ vccq-supply = <&vreg_l6c>;
+ vccq-max-microamp = <900000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l8g>;
+ vdda-pll-supply = <&vreg_l3g>;
+
+ status = "okay";
+};
+
+&ufs_card_hc {
+ reset-gpios = <&tlmm 229 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l10c>;
+ vcc-max-microamp = <800000>;
+ vccq-supply = <&vreg_l3c>;
+ vccq-max-microamp = <900000>;
+
+ status = "okay";
+};
+
+&ufs_card_phy {
+ vdda-phy-supply = <&vreg_l8g>;
+ vdda-pll-supply = <&vreg_l3g>;
+
+ status = "okay";
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_dwc3 {
+ /* TODO: Define USB-C connector properly */
+ dr_mode = "peripheral";
+};
+
+&usb_0_hsphy {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7a>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy {
+ vdda-phy-supply = <&vreg_l3a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ /* TODO: Define USB-C connector properly */
+ dr_mode = "host";
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l1c>;
+ vdda18-supply = <&vreg_l7c>;
+ vdda33-supply = <&vreg_l2c>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ vdda-phy-supply = <&vreg_l4c>;
+ vdda-pll-supply = <&vreg_l1c>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy0 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy1 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy2 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy3 {
+ vdda-pll-supply = <&vreg_l5a>;
+ vdda18-supply = <&vreg_l7g>;
+ vdda33-supply = <&vreg_l13a>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy0 {
+ vdda-phy-supply = <&vreg_l3a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy1 {
+ vdda-phy-supply = <&vreg_l3a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
diff --git a/arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts
new file mode 100644
index 000000000000..87077f7a321c
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "sa8295p-adp.dtsi"
+
+/ {
+ model = "Qualcomm SA8540 ADP";
+ compatible = "qcom,sa8540p-adp-ride", "qcom,sa8540p";
+};
--
2.17.1
On 21/07/2022 17:40, Parikshit Pareek wrote:
> Create new dts file specific for Qdrive board based on sa8540p chipset.
s/dts/DTS/
s/sa8450p/SA8450P/
> Introduce common dtsi file sa8295p-adp.dtsi, to be included for adp and
> Qdrive board.
Thank you for your patch. There is something to discuss/improve.
>
> Signed-off-by: Parikshit Pareek <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 378 +----------------
> arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi | 385 ++++++++++++++++++
> arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts | 15 +
> 4 files changed, 403 insertions(+), 376 deletions(-)
> create mode 100644 arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 9e2a13d75f9d..fa0abcf7660b 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sa8540p-adp-ride.dtb
Align formatting with the rest.
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> index 9398f0349944..adb6637117bc 100644
> --- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> @@ -2,388 +2,14 @@
> /*
> * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> * Copyright (c) 2022, Linaro Limited
> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> /dts-v1/;
>
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> -#include <dt-bindings/spmi/spmi.h>
> -
> -#include "sa8540p.dtsi"
> +#include "sa8295p-adp.dtsi"
>
> / {
> model = "Qualcomm SA8295P ADP";
> compatible = "qcom,sa8295p-adp", "qcom,sa8540p";
> -
> - aliases {
> - serial0 = &qup2_uart17;
> - };
> -
> - chosen {
> - stdout-path = "serial0:115200n8";
> - };
> -};
> -
You need to split the patch. First into DTSI split, so we can easily
compare the diffs. Then add new board.
Best regards,
Krzysztof
Hello!
On 21.07.2022 17:40, Parikshit Pareek wrote:
> Create new dts file specific for Qdrive board based on sa8540p chipset.
Is the SA8540P any different than SA8295P? My wild guess is that they're
binned versions of each other with different DVFS levels.. That could
use a separate SoC DTSI to hold these differences should that be true..
> Introduce common dtsi file sa8295p-adp.dtsi, to be included for adp and
> Qdrive board.
>
> Signed-off-by: Parikshit Pareek <[email protected]>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 378 +----------------
> arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi | 385 ++++++++++++++++++
> arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts | 15 +
> 4 files changed, 403 insertions(+), 376 deletions(-)
> create mode 100644 arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
> create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 9e2a13d75f9d..fa0abcf7660b 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sa8540p-adp-ride.dtb
This needs to be a tab.
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> index 9398f0349944..adb6637117bc 100644
> --- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> @@ -2,388 +2,14 @@
> /*
> * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> * Copyright (c) 2022, Linaro Limited
> + * Copyright (c) 2022 Qualcomm Innovaion Center, Inc. All rights reserved.
Please add a comma after the year to keep it consistent.
> */
>
> /dts-v1/;
[...]
> diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi b/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
> new file mode 100644
> index 000000000000..75ef77b7cac1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
Are the boards based on each other? Or on a similar base platform?
Maybe sa8295p/sa8540p/sasomethingelse-automotive.dtsi could be a
better name in the latter case?
[...]
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts
> @@ -0,0 +1,15 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Linaro Limited
> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
> + */
> +
> +/dts-v1/;
> +
> +#include "sa8295p-adp.dtsi"
> +
> +/ {
> + model = "Qualcomm SA8540 ADP";
So "Qdrive board" == SA8540 ADP == SA8540 ADP Ride? Or is there
a base platform for all of them? Maybe the Qdrive is simply based
on the ADPs? Is there a clear distinction between ADP and ADP Ride?
Konrad
> + compatible = "qcom,sa8540p-adp-ride", "qcom,sa8540p";
> +};
On Thu, Jul 21, 2022 at 08:41:34PM +0200, Konrad Dybcio wrote:
>
> Hello!
>
> On 21.07.2022 17:40, Parikshit Pareek wrote:
> > Create new dts file specific for Qdrive board based on sa8540p chipset.
> Is the SA8540P any different than SA8295P? My wild guess is that they're
> binned versions of each other with different DVFS levels.. That could
> use a separate SoC DTSI to hold these differences should that be true..
>
>
> > Introduce common dtsi file sa8295p-adp.dtsi, to be included for adp and
> > Qdrive board.
> >
> > Signed-off-by: Parikshit Pareek <[email protected]>
> > ---
> > arch/arm64/boot/dts/qcom/Makefile | 1 +
> > arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 378 +----------------
> > arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi | 385 ++++++++++++++++++
> > arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts | 15 +
> > 4 files changed, 403 insertions(+), 376 deletions(-)
> > create mode 100644 arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
> > create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts
> >
> > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> > index 9e2a13d75f9d..fa0abcf7660b 100644
> > --- a/arch/arm64/boot/dts/qcom/Makefile
> > +++ b/arch/arm64/boot/dts/qcom/Makefile
> > @@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
> > +dtb-$(CONFIG_ARCH_QCOM) += sa8540p-adp-ride.dtb
> This needs to be a tab.
>
>
> > dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb
> > dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb
> > diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> > index 9398f0349944..adb6637117bc 100644
> > --- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> > +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> > @@ -2,388 +2,14 @@
> > /*
> > * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> > * Copyright (c) 2022, Linaro Limited
> > + * Copyright (c) 2022 Qualcomm Innovaion Center, Inc. All rights reserved.
> Please add a comma after the year to keep it consistent.
>
>
> > */
> >
> > /dts-v1/;
>
> [...]
>
> > diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi b/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
> > new file mode 100644
> > index 000000000000..75ef77b7cac1
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dtsi
> Are the boards based on each other? Or on a similar base platform?
> Maybe sa8295p/sa8540p/sasomethingelse-automotive.dtsi could be a
> better name in the latter case?
Thanks, agreed.
>
>
> [...]
>
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/sa8540p-adp-ride.dts
> > @@ -0,0 +1,15 @@
> > +// SPDX-License-Identifier: BSD-3-Clause
> > +/*
> > + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> > + * Copyright (c) 2022, Linaro Limited
> > + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sa8295p-adp.dtsi"
> > +
> > +/ {
> > + model = "Qualcomm SA8540 ADP";
> So "Qdrive board" == SA8540 ADP == SA8540 ADP Ride? Or is there
> a base platform for all of them? Maybe the Qdrive is simply based
> on the ADPs? Is there a clear distinction between ADP and ADP Ride?
Yes, Qdrive board" == SA8540 ADP == SA8540 ADP Ride. ADP is common to
many boards, one being Qdrive or ADP ride.
>
> Konrad
>
> > + compatible = "qcom,sa8540p-adp-ride", "qcom,sa8540p";
> > +};
Regards,
Parikshit Pareek