changes since v4:
- remove int case from a printk in p1
- include tags into commit messages
changes since v3:
- update Kconfig as well
- drop chip names from comment in driver header
- add manufacturer check for Fintek again, Nuvoton not possible
- drop revision printing for Nuvoton
- restructure defines again
- add new model 427G
changes since v2: (p1 only)
- rename macros that change behavior
- use chip type not device id in the macros
- reorder defines a bit
changes since v1:
- remove unused define
- fix bug where (base + 2) was used as second data bit
- add macros for "inverted" and "single data bit"
This series first enables a SuperIO GPIO driver to support a chip from
the vendor Nuvoton, the driver is for Fintek devices but those just are
very similar. And in watchdog and hwmon subsystems these SuperIO drivers
also share code and are sometimes called a family.
In another step the individual banks receive a label to tell them apart,
a step which potentially changes an interface to legacy users that might
rely on all banks having the same label, or an exact label. But since a
later patch wants to use GPIO_LOOKUP unique labels are needed and i
decided to assign them for all supported chips.
In a following patch the Simatic GPIO LED driver is extended to provide
LEDs in case that SuperIO GPIO driver can be loaded.
Last but not least the watchdog module of that same SuperIO gets loaded
on a best effort basis.
The very last patch enables a second model of that same board type.
Henning Schild (5):
gpio-f7188x: Add GPIO support for Nuvoton NCT6116
gpio-f7188x: use unique labels for banks/chips
leds: simatic-ipc-leds-gpio: add new model 227G
platform/x86: simatic-ipc: enable watchdog for 227G
platform/x86: simatic-ipc: add new model 427G
drivers/gpio/Kconfig | 3 +-
drivers/gpio/gpio-f7188x.c | 228 +++++++++++-------
drivers/leds/simple/simatic-ipc-leds-gpio.c | 42 +++-
drivers/platform/x86/simatic-ipc.c | 10 +-
.../platform_data/x86/simatic-ipc-base.h | 1 +
include/linux/platform_data/x86/simatic-ipc.h | 2 +
6 files changed, 193 insertions(+), 93 deletions(-)
--
2.35.1
This adds support of the Siemens Simatic IPC227G. Its LEDs are connected
to GPIO pins provided by the gpio-f7188x module. We make sure that
gets loaded, if not enabled in the kernel config no LED support will be
available.
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Henning Schild <[email protected]>
---
drivers/leds/simple/simatic-ipc-leds-gpio.c | 42 ++++++++++++++++---
drivers/platform/x86/simatic-ipc.c | 4 +-
.../platform_data/x86/simatic-ipc-base.h | 1 +
include/linux/platform_data/x86/simatic-ipc.h | 1 +
4 files changed, 42 insertions(+), 6 deletions(-)
diff --git a/drivers/leds/simple/simatic-ipc-leds-gpio.c b/drivers/leds/simple/simatic-ipc-leds-gpio.c
index 4c9e663a90ba..0d73dcbeec2d 100644
--- a/drivers/leds/simple/simatic-ipc-leds-gpio.c
+++ b/drivers/leds/simple/simatic-ipc-leds-gpio.c
@@ -13,28 +13,45 @@
#include <linux/leds.h>
#include <linux/module.h>
#include <linux/platform_device.h>
+#include <linux/platform_data/x86/simatic-ipc-base.h>
-static struct gpiod_lookup_table simatic_ipc_led_gpio_table = {
+struct gpiod_lookup_table *simatic_ipc_led_gpio_table;
+
+static struct gpiod_lookup_table simatic_ipc_led_gpio_table_127e = {
.dev_id = "leds-gpio",
.table = {
- GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 51, NULL, 0, GPIO_ACTIVE_LOW),
GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 52, NULL, 1, GPIO_ACTIVE_LOW),
GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 53, NULL, 2, GPIO_ACTIVE_LOW),
GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 57, NULL, 3, GPIO_ACTIVE_LOW),
GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 58, NULL, 4, GPIO_ACTIVE_LOW),
GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 60, NULL, 5, GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 51, NULL, 0, GPIO_ACTIVE_LOW),
GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 56, NULL, 6, GPIO_ACTIVE_LOW),
GPIO_LOOKUP_IDX("apollolake-pinctrl.0", 59, NULL, 7, GPIO_ACTIVE_HIGH),
},
};
+static struct gpiod_lookup_table simatic_ipc_led_gpio_table_227g = {
+ .dev_id = "leds-gpio",
+ .table = {
+ GPIO_LOOKUP_IDX("gpio-f7188x-2", 0, NULL, 0, GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP_IDX("gpio-f7188x-2", 1, NULL, 1, GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP_IDX("gpio-f7188x-2", 2, NULL, 2, GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP_IDX("gpio-f7188x-2", 3, NULL, 3, GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP_IDX("gpio-f7188x-2", 4, NULL, 4, GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP_IDX("gpio-f7188x-2", 5, NULL, 5, GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP_IDX("gpio-f7188x-3", 6, NULL, 6, GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("gpio-f7188x-3", 7, NULL, 7, GPIO_ACTIVE_HIGH),
+ }
+};
+
static const struct gpio_led simatic_ipc_gpio_leds[] = {
- { .name = "green:" LED_FUNCTION_STATUS "-3" },
{ .name = "red:" LED_FUNCTION_STATUS "-1" },
{ .name = "green:" LED_FUNCTION_STATUS "-1" },
{ .name = "red:" LED_FUNCTION_STATUS "-2" },
{ .name = "green:" LED_FUNCTION_STATUS "-2" },
{ .name = "red:" LED_FUNCTION_STATUS "-3" },
+ { .name = "green:" LED_FUNCTION_STATUS "-3" },
};
static const struct gpio_led_platform_data simatic_ipc_gpio_leds_pdata = {
@@ -46,7 +63,7 @@ static struct platform_device *simatic_leds_pdev;
static int simatic_ipc_leds_gpio_remove(struct platform_device *pdev)
{
- gpiod_remove_lookup_table(&simatic_ipc_led_gpio_table);
+ gpiod_remove_lookup_table(simatic_ipc_led_gpio_table);
platform_device_unregister(simatic_leds_pdev);
return 0;
@@ -54,10 +71,25 @@ static int simatic_ipc_leds_gpio_remove(struct platform_device *pdev)
static int simatic_ipc_leds_gpio_probe(struct platform_device *pdev)
{
+ const struct simatic_ipc_platform *plat = pdev->dev.platform_data;
struct gpio_desc *gpiod;
int err;
- gpiod_add_lookup_table(&simatic_ipc_led_gpio_table);
+ switch (plat->devmode) {
+ case SIMATIC_IPC_DEVICE_127E:
+ simatic_ipc_led_gpio_table = &simatic_ipc_led_gpio_table_127e;
+ break;
+ case SIMATIC_IPC_DEVICE_227G:
+ if (!IS_ENABLED(CONFIG_GPIO_F7188X))
+ return -ENODEV;
+ request_module("gpio-f7188x");
+ simatic_ipc_led_gpio_table = &simatic_ipc_led_gpio_table_227g;
+ break;
+ default:
+ return -ENODEV;
+ }
+
+ gpiod_add_lookup_table(simatic_ipc_led_gpio_table);
simatic_leds_pdev = platform_device_register_resndata(NULL,
"leds-gpio", PLATFORM_DEVID_NONE, NULL, 0,
&simatic_ipc_gpio_leds_pdata,
diff --git a/drivers/platform/x86/simatic-ipc.c b/drivers/platform/x86/simatic-ipc.c
index ca3647b751d5..1825ef21a86d 100644
--- a/drivers/platform/x86/simatic-ipc.c
+++ b/drivers/platform/x86/simatic-ipc.c
@@ -41,6 +41,7 @@ static struct {
{SIMATIC_IPC_IPC127E, SIMATIC_IPC_DEVICE_127E, SIMATIC_IPC_DEVICE_NONE},
{SIMATIC_IPC_IPC227D, SIMATIC_IPC_DEVICE_227D, SIMATIC_IPC_DEVICE_NONE},
{SIMATIC_IPC_IPC227E, SIMATIC_IPC_DEVICE_427E, SIMATIC_IPC_DEVICE_227E},
+ {SIMATIC_IPC_IPC227G, SIMATIC_IPC_DEVICE_227G, SIMATIC_IPC_DEVICE_NONE},
{SIMATIC_IPC_IPC277E, SIMATIC_IPC_DEVICE_NONE, SIMATIC_IPC_DEVICE_227E},
{SIMATIC_IPC_IPC427D, SIMATIC_IPC_DEVICE_427E, SIMATIC_IPC_DEVICE_NONE},
{SIMATIC_IPC_IPC427E, SIMATIC_IPC_DEVICE_427E, SIMATIC_IPC_DEVICE_427E},
@@ -65,7 +66,8 @@ static int register_platform_devices(u32 station_id)
}
if (ledmode != SIMATIC_IPC_DEVICE_NONE) {
- if (ledmode == SIMATIC_IPC_DEVICE_127E)
+ if (ledmode == SIMATIC_IPC_DEVICE_127E ||
+ ledmode == SIMATIC_IPC_DEVICE_227G)
pdevname = KBUILD_MODNAME "_leds_gpio";
platform_data.devmode = ledmode;
ipc_led_platform_device =
diff --git a/include/linux/platform_data/x86/simatic-ipc-base.h b/include/linux/platform_data/x86/simatic-ipc-base.h
index 39fefd48cf4d..57d6a10dfc9e 100644
--- a/include/linux/platform_data/x86/simatic-ipc-base.h
+++ b/include/linux/platform_data/x86/simatic-ipc-base.h
@@ -19,6 +19,7 @@
#define SIMATIC_IPC_DEVICE_427E 2
#define SIMATIC_IPC_DEVICE_127E 3
#define SIMATIC_IPC_DEVICE_227E 4
+#define SIMATIC_IPC_DEVICE_227G 5
struct simatic_ipc_platform {
u8 devmode;
diff --git a/include/linux/platform_data/x86/simatic-ipc.h b/include/linux/platform_data/x86/simatic-ipc.h
index f3b76b39776b..7a2e79f3be0b 100644
--- a/include/linux/platform_data/x86/simatic-ipc.h
+++ b/include/linux/platform_data/x86/simatic-ipc.h
@@ -31,6 +31,7 @@ enum simatic_ipc_station_ids {
SIMATIC_IPC_IPC427E = 0x00000A01,
SIMATIC_IPC_IPC477E = 0x00000A02,
SIMATIC_IPC_IPC127E = 0x00000D01,
+ SIMATIC_IPC_IPC227G = 0x00000F01,
};
static inline u32 simatic_ipc_get_station_id(u8 *data, int max_len)
--
2.35.1
This adds support for the Siemens Simatic IPC427G. A board which
basically works like the 227G added in a previous patch. So all there is
to do is to add the station_id and make it take all the 227G branches.
Reviewed-by: Andy Shevchenko <[email protected]>
Signed-off-by: Henning Schild <[email protected]>
---
drivers/platform/x86/simatic-ipc.c | 11 +++++++----
include/linux/platform_data/x86/simatic-ipc.h | 1 +
2 files changed, 8 insertions(+), 4 deletions(-)
diff --git a/drivers/platform/x86/simatic-ipc.c b/drivers/platform/x86/simatic-ipc.c
index 8dd686d1c9f1..ca76076fc706 100644
--- a/drivers/platform/x86/simatic-ipc.c
+++ b/drivers/platform/x86/simatic-ipc.c
@@ -41,11 +41,12 @@ static struct {
{SIMATIC_IPC_IPC127E, SIMATIC_IPC_DEVICE_127E, SIMATIC_IPC_DEVICE_NONE},
{SIMATIC_IPC_IPC227D, SIMATIC_IPC_DEVICE_227D, SIMATIC_IPC_DEVICE_NONE},
{SIMATIC_IPC_IPC227E, SIMATIC_IPC_DEVICE_427E, SIMATIC_IPC_DEVICE_227E},
- {SIMATIC_IPC_IPC227G, SIMATIC_IPC_DEVICE_227G, SIMATIC_IPC_DEVICE_NONE},
+ {SIMATIC_IPC_IPC227G, SIMATIC_IPC_DEVICE_227G, SIMATIC_IPC_DEVICE_227G},
{SIMATIC_IPC_IPC277E, SIMATIC_IPC_DEVICE_NONE, SIMATIC_IPC_DEVICE_227E},
{SIMATIC_IPC_IPC427D, SIMATIC_IPC_DEVICE_427E, SIMATIC_IPC_DEVICE_NONE},
{SIMATIC_IPC_IPC427E, SIMATIC_IPC_DEVICE_427E, SIMATIC_IPC_DEVICE_427E},
{SIMATIC_IPC_IPC477E, SIMATIC_IPC_DEVICE_NONE, SIMATIC_IPC_DEVICE_427E},
+ {SIMATIC_IPC_IPC427G, SIMATIC_IPC_DEVICE_227G, SIMATIC_IPC_DEVICE_227G},
};
static int register_platform_devices(u32 station_id)
@@ -82,6 +83,11 @@ static int register_platform_devices(u32 station_id)
ipc_led_platform_device->name);
}
+ if (wdtmode == SIMATIC_IPC_DEVICE_227G) {
+ request_module("w83627hf_wdt");
+ return 0;
+ }
+
if (wdtmode != SIMATIC_IPC_DEVICE_NONE) {
platform_data.devmode = wdtmode;
ipc_wdt_platform_device =
@@ -96,9 +102,6 @@ static int register_platform_devices(u32 station_id)
ipc_wdt_platform_device->name);
}
- if (station_id == SIMATIC_IPC_IPC227G)
- request_module("w83627hf_wdt");
-
if (ledmode == SIMATIC_IPC_DEVICE_NONE &&
wdtmode == SIMATIC_IPC_DEVICE_NONE) {
pr_warn("unsupported IPC detected, station id=%08x\n",
diff --git a/include/linux/platform_data/x86/simatic-ipc.h b/include/linux/platform_data/x86/simatic-ipc.h
index 7a2e79f3be0b..632320ec8f08 100644
--- a/include/linux/platform_data/x86/simatic-ipc.h
+++ b/include/linux/platform_data/x86/simatic-ipc.h
@@ -32,6 +32,7 @@ enum simatic_ipc_station_ids {
SIMATIC_IPC_IPC477E = 0x00000A02,
SIMATIC_IPC_IPC127E = 0x00000D01,
SIMATIC_IPC_IPC227G = 0x00000F01,
+ SIMATIC_IPC_IPC427G = 0x00001001,
};
static inline u32 simatic_ipc_get_station_id(u8 *data, int max_len)
--
2.35.1
Add GPIO support for Nuvoton NCT6116 chip. Nuvoton SuperIO chips are
very similar to the ones from Fintek. In other subsystems they also
share drivers and are called a family of drivers.
For the GPIO subsystem the only difference is that the direction bit is
reversed and that there is only one data bit per pin. On the SuperIO
level the logical device is another one.
On a chip level we do not have a manufacturer ID to check and also no
revision.
Signed-off-by: Henning Schild <[email protected]>
---
drivers/gpio/Kconfig | 3 +-
drivers/gpio/gpio-f7188x.c | 106 ++++++++++++++++++++++++++++---------
2 files changed, 83 insertions(+), 26 deletions(-)
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 0642f579196f..3f64345fe40b 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -874,10 +874,11 @@ config GPIO_104_IDI_48
module parameter.
config GPIO_F7188X
- tristate "F71869, F71869A, F71882FG, F71889F and F81866 GPIO support"
+ tristate "Fintek and Nuvoton Super-I/O GPIO support"
help
This option enables support for GPIOs found on Fintek Super-I/O
chips F71869, F71869A, F71882FG, F71889F and F81866.
+ As well as Nuvoton Super-I/O chip NCT6116D.
To compile this driver as a module, choose M here: the module will
be called f7188x-gpio.
diff --git a/drivers/gpio/gpio-f7188x.c b/drivers/gpio/gpio-f7188x.c
index 18a3147f5a42..b73bf28bf347 100644
--- a/drivers/gpio/gpio-f7188x.c
+++ b/drivers/gpio/gpio-f7188x.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0-or-later
/*
- * GPIO driver for Fintek Super-I/O F71869, F71869A, F71882, F71889 and F81866
+ * GPIO driver for Fintek and Nuvoton Super-I/O chips
*
* Copyright (C) 2010-2013 LaCie
*
@@ -21,23 +21,36 @@
*/
#define SIO_LDSEL 0x07 /* Logical device select */
#define SIO_DEVID 0x20 /* Device ID (2 bytes) */
-#define SIO_DEVREV 0x22 /* Device revision */
-#define SIO_MANID 0x23 /* Fintek ID (2 bytes) */
-#define SIO_LD_GPIO 0x06 /* GPIO logical device */
#define SIO_UNLOCK_KEY 0x87 /* Key to enable Super-I/O */
#define SIO_LOCK_KEY 0xAA /* Key to disable Super-I/O */
-#define SIO_FINTEK_ID 0x1934 /* Manufacturer ID */
+/*
+ * Fintek devices.
+ */
+#define SIO_FINTEK_DEVREV 0x22 /* Fintek Device revision */
+#define SIO_FINTEK_MANID 0x23 /* Fintek ID (2 bytes) */
+
+#define SIO_FINTEK_ID 0x1934 /* Manufacturer ID */
+
#define SIO_F71869_ID 0x0814 /* F71869 chipset ID */
#define SIO_F71869A_ID 0x1007 /* F71869A chipset ID */
#define SIO_F71882_ID 0x0541 /* F71882 chipset ID */
#define SIO_F71889_ID 0x0909 /* F71889 chipset ID */
#define SIO_F71889A_ID 0x1005 /* F71889A chipset ID */
#define SIO_F81866_ID 0x1010 /* F81866 chipset ID */
-#define SIO_F81804_ID 0x1502 /* F81804 chipset ID, same for f81966 */
+#define SIO_F81804_ID 0x1502 /* F81804 chipset ID, same for F81966 */
#define SIO_F81865_ID 0x0704 /* F81865 chipset ID */
+#define SIO_LD_GPIO_FINTEK 0x06 /* GPIO logical device */
+
+/*
+ * Nuvoton devices.
+ */
+#define SIO_NCT6116D_ID 0xD283 /* NCT6116D chipset ID */
+
+#define SIO_LD_GPIO_NUVOTON 0x07 /* GPIO logical device */
+
enum chips {
f71869,
@@ -48,6 +61,7 @@ enum chips {
f81866,
f81804,
f81865,
+ nct6116d,
};
static const char * const f7188x_names[] = {
@@ -59,10 +73,12 @@ static const char * const f7188x_names[] = {
"f81866",
"f81804",
"f81865",
+ "nct6116d",
};
struct f7188x_sio {
int addr;
+ int device;
enum chips type;
};
@@ -170,6 +186,9 @@ static int f7188x_gpio_set_config(struct gpio_chip *chip, unsigned offset,
/* Output mode register (0:open drain 1:push-pull). */
#define gpio_out_mode(base) (base + 3)
+#define gpio_dir_invert(type) ((type) == nct6116d)
+#define gpio_data_single(type) ((type) == nct6116d)
+
static struct f7188x_gpio_bank f71869_gpio_bank[] = {
F7188X_GPIO_BANK(0, 6, 0xF0),
F7188X_GPIO_BANK(10, 8, 0xE0),
@@ -254,6 +273,17 @@ static struct f7188x_gpio_bank f81865_gpio_bank[] = {
F7188X_GPIO_BANK(60, 5, 0x90),
};
+static struct f7188x_gpio_bank nct6116d_gpio_bank[] = {
+ F7188X_GPIO_BANK(0, 8, 0xE0),
+ F7188X_GPIO_BANK(10, 8, 0xE4),
+ F7188X_GPIO_BANK(20, 8, 0xE8),
+ F7188X_GPIO_BANK(30, 8, 0xEC),
+ F7188X_GPIO_BANK(40, 8, 0xF0),
+ F7188X_GPIO_BANK(50, 8, 0xF4),
+ F7188X_GPIO_BANK(60, 8, 0xF8),
+ F7188X_GPIO_BANK(70, 1, 0xFC),
+};
+
static int f7188x_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
{
int err;
@@ -264,13 +294,16 @@ static int f7188x_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
err = superio_enter(sio->addr);
if (err)
return err;
- superio_select(sio->addr, SIO_LD_GPIO);
+ superio_select(sio->addr, sio->device);
dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
superio_exit(sio->addr);
- if (dir & 1 << offset)
+ if (gpio_dir_invert(sio->type))
+ dir = ~dir;
+
+ if (dir & BIT(offset))
return GPIO_LINE_DIRECTION_OUT;
return GPIO_LINE_DIRECTION_IN;
@@ -286,10 +319,14 @@ static int f7188x_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
err = superio_enter(sio->addr);
if (err)
return err;
- superio_select(sio->addr, SIO_LD_GPIO);
+ superio_select(sio->addr, sio->device);
dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
- dir &= ~BIT(offset);
+
+ if (gpio_dir_invert(sio->type))
+ dir |= BIT(offset);
+ else
+ dir &= ~BIT(offset);
superio_outb(sio->addr, gpio_dir(bank->regbase), dir);
superio_exit(sio->addr);
@@ -307,11 +344,11 @@ static int f7188x_gpio_get(struct gpio_chip *chip, unsigned offset)
err = superio_enter(sio->addr);
if (err)
return err;
- superio_select(sio->addr, SIO_LD_GPIO);
+ superio_select(sio->addr, sio->device);
dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
dir = !!(dir & BIT(offset));
- if (dir)
+ if (gpio_data_single(sio->type) || dir)
data = superio_inb(sio->addr, gpio_data_out(bank->regbase));
else
data = superio_inb(sio->addr, gpio_data_in(bank->regbase));
@@ -332,7 +369,7 @@ static int f7188x_gpio_direction_out(struct gpio_chip *chip,
err = superio_enter(sio->addr);
if (err)
return err;
- superio_select(sio->addr, SIO_LD_GPIO);
+ superio_select(sio->addr, sio->device);
data_out = superio_inb(sio->addr, gpio_data_out(bank->regbase));
if (value)
@@ -342,7 +379,10 @@ static int f7188x_gpio_direction_out(struct gpio_chip *chip,
superio_outb(sio->addr, gpio_data_out(bank->regbase), data_out);
dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
- dir |= BIT(offset);
+ if (gpio_dir_invert(sio->type))
+ dir &= ~BIT(offset);
+ else
+ dir |= BIT(offset);
superio_outb(sio->addr, gpio_dir(bank->regbase), dir);
superio_exit(sio->addr);
@@ -360,7 +400,7 @@ static void f7188x_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
err = superio_enter(sio->addr);
if (err)
return;
- superio_select(sio->addr, SIO_LD_GPIO);
+ superio_select(sio->addr, sio->device);
data_out = superio_inb(sio->addr, gpio_data_out(bank->regbase));
if (value)
@@ -388,7 +428,7 @@ static int f7188x_gpio_set_config(struct gpio_chip *chip, unsigned offset,
err = superio_enter(sio->addr);
if (err)
return err;
- superio_select(sio->addr, SIO_LD_GPIO);
+ superio_select(sio->addr, sio->device);
data = superio_inb(sio->addr, gpio_out_mode(bank->regbase));
if (param == PIN_CONFIG_DRIVE_OPEN_DRAIN)
@@ -449,6 +489,10 @@ static int f7188x_gpio_probe(struct platform_device *pdev)
data->nr_bank = ARRAY_SIZE(f81865_gpio_bank);
data->bank = f81865_gpio_bank;
break;
+ case nct6116d:
+ data->nr_bank = ARRAY_SIZE(nct6116d_gpio_bank);
+ data->bank = nct6116d_gpio_bank;
+ break;
default:
return -ENODEV;
}
@@ -479,18 +523,15 @@ static int __init f7188x_find(int addr, struct f7188x_sio *sio)
{
int err;
u16 devid;
+ u16 manid;
err = superio_enter(addr);
if (err)
return err;
err = -ENODEV;
- devid = superio_inw(addr, SIO_MANID);
- if (devid != SIO_FINTEK_ID) {
- pr_debug(DRVNAME ": Not a Fintek device at 0x%08x\n", addr);
- goto err;
- }
+ sio->device = SIO_LD_GPIO_FINTEK;
devid = superio_inw(addr, SIO_DEVID);
switch (devid) {
case SIO_F71869_ID:
@@ -517,17 +558,32 @@ static int __init f7188x_find(int addr, struct f7188x_sio *sio)
case SIO_F81865_ID:
sio->type = f81865;
break;
+ case SIO_NCT6116D_ID:
+ sio->device = SIO_LD_GPIO_NUVOTON;
+ sio->type = nct6116d;
+ break;
default:
- pr_info(DRVNAME ": Unsupported Fintek device 0x%04x\n", devid);
+ pr_info(DRVNAME ": Unsupported device 0x%04x\n", devid);
goto err;
}
+
+ /* double check manufacturer where possible */
+ if (sio->type != nct6116d) {
+ manid = superio_inw(addr, SIO_FINTEK_MANID);
+ if (manid != SIO_FINTEK_ID) {
+ pr_debug(DRVNAME ": Not a Fintek device at 0x%08x\n", addr);
+ goto err;
+ }
+ }
+
sio->addr = addr;
err = 0;
- pr_info(DRVNAME ": Found %s at %#x, revision %d\n",
+ pr_info(DRVNAME ": Found %s at %#x\n",
f7188x_names[sio->type],
- (unsigned int) addr,
- (int) superio_inb(addr, SIO_DEVREV));
+ (unsigned int)addr);
+ if (sio->type != nct6116d)
+ pr_info(DRVNAME ": revision %d\n", superio_inb(addr, SIO_FINTEK_DEVREV));
err:
superio_exit(addr);
--
2.35.1
Just load the watchdog module, after having identified that machine.
That watchdog module does not have any autoloading support.
Reviewed-by: Andy Shevchenko <[email protected]>
Signed-off-by: Henning Schild <[email protected]>
---
drivers/platform/x86/simatic-ipc.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/platform/x86/simatic-ipc.c b/drivers/platform/x86/simatic-ipc.c
index 1825ef21a86d..8dd686d1c9f1 100644
--- a/drivers/platform/x86/simatic-ipc.c
+++ b/drivers/platform/x86/simatic-ipc.c
@@ -96,6 +96,9 @@ static int register_platform_devices(u32 station_id)
ipc_wdt_platform_device->name);
}
+ if (station_id == SIMATIC_IPC_IPC227G)
+ request_module("w83627hf_wdt");
+
if (ledmode == SIMATIC_IPC_DEVICE_NONE &&
wdtmode == SIMATIC_IPC_DEVICE_NONE) {
pr_warn("unsupported IPC detected, station id=%08x\n",
--
2.35.1
So that drivers building on top can find those pins with GPIO_LOOKUP
helpers.
Reviewed-by: Andy Shevchenko <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Acked-by: Simon Guinot <[email protected]>
Signed-off-by: Henning Schild <[email protected]>
---
drivers/gpio/gpio-f7188x.c | 138 ++++++++++++++++++-------------------
1 file changed, 69 insertions(+), 69 deletions(-)
diff --git a/drivers/gpio/gpio-f7188x.c b/drivers/gpio/gpio-f7188x.c
index b73bf28bf347..565840586150 100644
--- a/drivers/gpio/gpio-f7188x.c
+++ b/drivers/gpio/gpio-f7188x.c
@@ -162,10 +162,10 @@ static void f7188x_gpio_set(struct gpio_chip *chip, unsigned offset, int value);
static int f7188x_gpio_set_config(struct gpio_chip *chip, unsigned offset,
unsigned long config);
-#define F7188X_GPIO_BANK(_base, _ngpio, _regbase) \
+#define F7188X_GPIO_BANK(_base, _ngpio, _regbase, _label) \
{ \
.chip = { \
- .label = DRVNAME, \
+ .label = _label, \
.owner = THIS_MODULE, \
.get_direction = f7188x_gpio_get_direction, \
.direction_input = f7188x_gpio_direction_in, \
@@ -190,98 +190,98 @@ static int f7188x_gpio_set_config(struct gpio_chip *chip, unsigned offset,
#define gpio_data_single(type) ((type) == nct6116d)
static struct f7188x_gpio_bank f71869_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 6, 0xF0),
- F7188X_GPIO_BANK(10, 8, 0xE0),
- F7188X_GPIO_BANK(20, 8, 0xD0),
- F7188X_GPIO_BANK(30, 8, 0xC0),
- F7188X_GPIO_BANK(40, 8, 0xB0),
- F7188X_GPIO_BANK(50, 5, 0xA0),
- F7188X_GPIO_BANK(60, 6, 0x90),
+ F7188X_GPIO_BANK(0, 6, 0xF0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 8, 0xE0, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xD0, DRVNAME "-2"),
+ F7188X_GPIO_BANK(30, 8, 0xC0, DRVNAME "-3"),
+ F7188X_GPIO_BANK(40, 8, 0xB0, DRVNAME "-4"),
+ F7188X_GPIO_BANK(50, 5, 0xA0, DRVNAME "-5"),
+ F7188X_GPIO_BANK(60, 6, 0x90, DRVNAME "-6"),
};
static struct f7188x_gpio_bank f71869a_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 6, 0xF0),
- F7188X_GPIO_BANK(10, 8, 0xE0),
- F7188X_GPIO_BANK(20, 8, 0xD0),
- F7188X_GPIO_BANK(30, 8, 0xC0),
- F7188X_GPIO_BANK(40, 8, 0xB0),
- F7188X_GPIO_BANK(50, 5, 0xA0),
- F7188X_GPIO_BANK(60, 8, 0x90),
- F7188X_GPIO_BANK(70, 8, 0x80),
+ F7188X_GPIO_BANK(0, 6, 0xF0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 8, 0xE0, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xD0, DRVNAME "-2"),
+ F7188X_GPIO_BANK(30, 8, 0xC0, DRVNAME "-3"),
+ F7188X_GPIO_BANK(40, 8, 0xB0, DRVNAME "-4"),
+ F7188X_GPIO_BANK(50, 5, 0xA0, DRVNAME "-5"),
+ F7188X_GPIO_BANK(60, 8, 0x90, DRVNAME "-6"),
+ F7188X_GPIO_BANK(70, 8, 0x80, DRVNAME "-7"),
};
static struct f7188x_gpio_bank f71882_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 8, 0xF0),
- F7188X_GPIO_BANK(10, 8, 0xE0),
- F7188X_GPIO_BANK(20, 8, 0xD0),
- F7188X_GPIO_BANK(30, 4, 0xC0),
- F7188X_GPIO_BANK(40, 4, 0xB0),
+ F7188X_GPIO_BANK(0, 8, 0xF0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 8, 0xE0, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xD0, DRVNAME "-2"),
+ F7188X_GPIO_BANK(30, 4, 0xC0, DRVNAME "-3"),
+ F7188X_GPIO_BANK(40, 4, 0xB0, DRVNAME "-4"),
};
static struct f7188x_gpio_bank f71889a_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 7, 0xF0),
- F7188X_GPIO_BANK(10, 7, 0xE0),
- F7188X_GPIO_BANK(20, 8, 0xD0),
- F7188X_GPIO_BANK(30, 8, 0xC0),
- F7188X_GPIO_BANK(40, 8, 0xB0),
- F7188X_GPIO_BANK(50, 5, 0xA0),
- F7188X_GPIO_BANK(60, 8, 0x90),
- F7188X_GPIO_BANK(70, 8, 0x80),
+ F7188X_GPIO_BANK(0, 7, 0xF0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 7, 0xE0, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xD0, DRVNAME "-2"),
+ F7188X_GPIO_BANK(30, 8, 0xC0, DRVNAME "-3"),
+ F7188X_GPIO_BANK(40, 8, 0xB0, DRVNAME "-4"),
+ F7188X_GPIO_BANK(50, 5, 0xA0, DRVNAME "-5"),
+ F7188X_GPIO_BANK(60, 8, 0x90, DRVNAME "-6"),
+ F7188X_GPIO_BANK(70, 8, 0x80, DRVNAME "-7"),
};
static struct f7188x_gpio_bank f71889_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 7, 0xF0),
- F7188X_GPIO_BANK(10, 7, 0xE0),
- F7188X_GPIO_BANK(20, 8, 0xD0),
- F7188X_GPIO_BANK(30, 8, 0xC0),
- F7188X_GPIO_BANK(40, 8, 0xB0),
- F7188X_GPIO_BANK(50, 5, 0xA0),
- F7188X_GPIO_BANK(60, 8, 0x90),
- F7188X_GPIO_BANK(70, 8, 0x80),
+ F7188X_GPIO_BANK(0, 7, 0xF0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 7, 0xE0, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xD0, DRVNAME "-2"),
+ F7188X_GPIO_BANK(30, 8, 0xC0, DRVNAME "-3"),
+ F7188X_GPIO_BANK(40, 8, 0xB0, DRVNAME "-4"),
+ F7188X_GPIO_BANK(50, 5, 0xA0, DRVNAME "-5"),
+ F7188X_GPIO_BANK(60, 8, 0x90, DRVNAME "-6"),
+ F7188X_GPIO_BANK(70, 8, 0x80, DRVNAME "-7"),
};
static struct f7188x_gpio_bank f81866_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 8, 0xF0),
- F7188X_GPIO_BANK(10, 8, 0xE0),
- F7188X_GPIO_BANK(20, 8, 0xD0),
- F7188X_GPIO_BANK(30, 8, 0xC0),
- F7188X_GPIO_BANK(40, 8, 0xB0),
- F7188X_GPIO_BANK(50, 8, 0xA0),
- F7188X_GPIO_BANK(60, 8, 0x90),
- F7188X_GPIO_BANK(70, 8, 0x80),
- F7188X_GPIO_BANK(80, 8, 0x88),
+ F7188X_GPIO_BANK(0, 8, 0xF0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 8, 0xE0, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xD0, DRVNAME "-2"),
+ F7188X_GPIO_BANK(30, 8, 0xC0, DRVNAME "-3"),
+ F7188X_GPIO_BANK(40, 8, 0xB0, DRVNAME "-4"),
+ F7188X_GPIO_BANK(50, 8, 0xA0, DRVNAME "-5"),
+ F7188X_GPIO_BANK(60, 8, 0x90, DRVNAME "-6"),
+ F7188X_GPIO_BANK(70, 8, 0x80, DRVNAME "-7"),
+ F7188X_GPIO_BANK(80, 8, 0x88, DRVNAME "-8"),
};
static struct f7188x_gpio_bank f81804_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 8, 0xF0),
- F7188X_GPIO_BANK(10, 8, 0xE0),
- F7188X_GPIO_BANK(20, 8, 0xD0),
- F7188X_GPIO_BANK(50, 8, 0xA0),
- F7188X_GPIO_BANK(60, 8, 0x90),
- F7188X_GPIO_BANK(70, 8, 0x80),
- F7188X_GPIO_BANK(90, 8, 0x98),
+ F7188X_GPIO_BANK(0, 8, 0xF0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 8, 0xE0, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xD0, DRVNAME "-2"),
+ F7188X_GPIO_BANK(50, 8, 0xA0, DRVNAME "-3"),
+ F7188X_GPIO_BANK(60, 8, 0x90, DRVNAME "-4"),
+ F7188X_GPIO_BANK(70, 8, 0x80, DRVNAME "-5"),
+ F7188X_GPIO_BANK(90, 8, 0x98, DRVNAME "-6"),
};
static struct f7188x_gpio_bank f81865_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 8, 0xF0),
- F7188X_GPIO_BANK(10, 8, 0xE0),
- F7188X_GPIO_BANK(20, 8, 0xD0),
- F7188X_GPIO_BANK(30, 8, 0xC0),
- F7188X_GPIO_BANK(40, 8, 0xB0),
- F7188X_GPIO_BANK(50, 8, 0xA0),
- F7188X_GPIO_BANK(60, 5, 0x90),
+ F7188X_GPIO_BANK(0, 8, 0xF0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 8, 0xE0, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xD0, DRVNAME "-2"),
+ F7188X_GPIO_BANK(30, 8, 0xC0, DRVNAME "-3"),
+ F7188X_GPIO_BANK(40, 8, 0xB0, DRVNAME "-4"),
+ F7188X_GPIO_BANK(50, 8, 0xA0, DRVNAME "-5"),
+ F7188X_GPIO_BANK(60, 5, 0x90, DRVNAME "-6"),
};
static struct f7188x_gpio_bank nct6116d_gpio_bank[] = {
- F7188X_GPIO_BANK(0, 8, 0xE0),
- F7188X_GPIO_BANK(10, 8, 0xE4),
- F7188X_GPIO_BANK(20, 8, 0xE8),
- F7188X_GPIO_BANK(30, 8, 0xEC),
- F7188X_GPIO_BANK(40, 8, 0xF0),
- F7188X_GPIO_BANK(50, 8, 0xF4),
- F7188X_GPIO_BANK(60, 8, 0xF8),
- F7188X_GPIO_BANK(70, 1, 0xFC),
+ F7188X_GPIO_BANK(0, 8, 0xE0, DRVNAME "-0"),
+ F7188X_GPIO_BANK(10, 8, 0xE4, DRVNAME "-1"),
+ F7188X_GPIO_BANK(20, 8, 0xE8, DRVNAME "-2"),
+ F7188X_GPIO_BANK(30, 8, 0xEC, DRVNAME "-3"),
+ F7188X_GPIO_BANK(40, 8, 0xF0, DRVNAME "-4"),
+ F7188X_GPIO_BANK(50, 8, 0xF4, DRVNAME "-5"),
+ F7188X_GPIO_BANK(60, 8, 0xF8, DRVNAME "-6"),
+ F7188X_GPIO_BANK(70, 1, 0xFC, DRVNAME "-7"),
};
static int f7188x_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
--
2.35.1
On Wed, Aug 24, 2022 at 5:04 PM Henning Schild
<[email protected]> wrote:
>
> Add GPIO support for Nuvoton NCT6116 chip. Nuvoton SuperIO chips are
> very similar to the ones from Fintek. In other subsystems they also
> share drivers and are called a family of drivers.
>
> For the GPIO subsystem the only difference is that the direction bit is
> reversed and that there is only one data bit per pin. On the SuperIO
> level the logical device is another one.
>
> On a chip level we do not have a manufacturer ID to check and also no
> revision.
...
> +#define gpio_dir_invert(type) ((type) == nct6116d)
> +#define gpio_data_single(type) ((type) == nct6116d)
What you are trying to do here is to put GPIO maintainers / heavy
contributors on a minefield (basically moving your job to their
shoulders). Please, provide a proper namespace and not gpio_ one. I'm
talking in my "GPIO heavy contributor" hat on.
With that fixed I can survive w/o pr_fmt() being in this patch. If you
are going to address this, you may add my tag in a new version.
--
With Best Regards,
Andy Shevchenko
On Wed, Aug 24, 2022 at 04:03:43PM +0200, Henning Schild wrote:
> Add GPIO support for Nuvoton NCT6116 chip. Nuvoton SuperIO chips are
> very similar to the ones from Fintek. In other subsystems they also
> share drivers and are called a family of drivers.
>
> For the GPIO subsystem the only difference is that the direction bit is
> reversed and that there is only one data bit per pin. On the SuperIO
> level the logical device is another one.
>
> On a chip level we do not have a manufacturer ID to check and also no
> revision.
>
> Signed-off-by: Henning Schild <[email protected]>
Acked-by: Simon Guinot <[email protected]>
> ---
> drivers/gpio/Kconfig | 3 +-
> drivers/gpio/gpio-f7188x.c | 106 ++++++++++++++++++++++++++++---------
> 2 files changed, 83 insertions(+), 26 deletions(-)
>
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 0642f579196f..3f64345fe40b 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -874,10 +874,11 @@ config GPIO_104_IDI_48
> module parameter.
>
> config GPIO_F7188X
> - tristate "F71869, F71869A, F71882FG, F71889F and F81866 GPIO support"
> + tristate "Fintek and Nuvoton Super-I/O GPIO support"
> help
> This option enables support for GPIOs found on Fintek Super-I/O
> chips F71869, F71869A, F71882FG, F71889F and F81866.
> + As well as Nuvoton Super-I/O chip NCT6116D.
>
> To compile this driver as a module, choose M here: the module will
> be called f7188x-gpio.
> diff --git a/drivers/gpio/gpio-f7188x.c b/drivers/gpio/gpio-f7188x.c
> index 18a3147f5a42..b73bf28bf347 100644
> --- a/drivers/gpio/gpio-f7188x.c
> +++ b/drivers/gpio/gpio-f7188x.c
> @@ -1,6 +1,6 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> /*
> - * GPIO driver for Fintek Super-I/O F71869, F71869A, F71882, F71889 and F81866
> + * GPIO driver for Fintek and Nuvoton Super-I/O chips
> *
> * Copyright (C) 2010-2013 LaCie
> *
> @@ -21,23 +21,36 @@
> */
> #define SIO_LDSEL 0x07 /* Logical device select */
> #define SIO_DEVID 0x20 /* Device ID (2 bytes) */
> -#define SIO_DEVREV 0x22 /* Device revision */
> -#define SIO_MANID 0x23 /* Fintek ID (2 bytes) */
>
> -#define SIO_LD_GPIO 0x06 /* GPIO logical device */
> #define SIO_UNLOCK_KEY 0x87 /* Key to enable Super-I/O */
> #define SIO_LOCK_KEY 0xAA /* Key to disable Super-I/O */
>
> -#define SIO_FINTEK_ID 0x1934 /* Manufacturer ID */
> +/*
> + * Fintek devices.
> + */
> +#define SIO_FINTEK_DEVREV 0x22 /* Fintek Device revision */
> +#define SIO_FINTEK_MANID 0x23 /* Fintek ID (2 bytes) */
> +
> +#define SIO_FINTEK_ID 0x1934 /* Manufacturer ID */
> +
> #define SIO_F71869_ID 0x0814 /* F71869 chipset ID */
> #define SIO_F71869A_ID 0x1007 /* F71869A chipset ID */
> #define SIO_F71882_ID 0x0541 /* F71882 chipset ID */
> #define SIO_F71889_ID 0x0909 /* F71889 chipset ID */
> #define SIO_F71889A_ID 0x1005 /* F71889A chipset ID */
> #define SIO_F81866_ID 0x1010 /* F81866 chipset ID */
> -#define SIO_F81804_ID 0x1502 /* F81804 chipset ID, same for f81966 */
> +#define SIO_F81804_ID 0x1502 /* F81804 chipset ID, same for F81966 */
> #define SIO_F81865_ID 0x0704 /* F81865 chipset ID */
>
> +#define SIO_LD_GPIO_FINTEK 0x06 /* GPIO logical device */
> +
> +/*
> + * Nuvoton devices.
> + */
> +#define SIO_NCT6116D_ID 0xD283 /* NCT6116D chipset ID */
> +
> +#define SIO_LD_GPIO_NUVOTON 0x07 /* GPIO logical device */
> +
>
> enum chips {
> f71869,
> @@ -48,6 +61,7 @@ enum chips {
> f81866,
> f81804,
> f81865,
> + nct6116d,
> };
>
> static const char * const f7188x_names[] = {
> @@ -59,10 +73,12 @@ static const char * const f7188x_names[] = {
> "f81866",
> "f81804",
> "f81865",
> + "nct6116d",
> };
>
> struct f7188x_sio {
> int addr;
> + int device;
> enum chips type;
> };
>
> @@ -170,6 +186,9 @@ static int f7188x_gpio_set_config(struct gpio_chip *chip, unsigned offset,
> /* Output mode register (0:open drain 1:push-pull). */
> #define gpio_out_mode(base) (base + 3)
>
> +#define gpio_dir_invert(type) ((type) == nct6116d)
> +#define gpio_data_single(type) ((type) == nct6116d)
> +
> static struct f7188x_gpio_bank f71869_gpio_bank[] = {
> F7188X_GPIO_BANK(0, 6, 0xF0),
> F7188X_GPIO_BANK(10, 8, 0xE0),
> @@ -254,6 +273,17 @@ static struct f7188x_gpio_bank f81865_gpio_bank[] = {
> F7188X_GPIO_BANK(60, 5, 0x90),
> };
>
> +static struct f7188x_gpio_bank nct6116d_gpio_bank[] = {
> + F7188X_GPIO_BANK(0, 8, 0xE0),
> + F7188X_GPIO_BANK(10, 8, 0xE4),
> + F7188X_GPIO_BANK(20, 8, 0xE8),
> + F7188X_GPIO_BANK(30, 8, 0xEC),
> + F7188X_GPIO_BANK(40, 8, 0xF0),
> + F7188X_GPIO_BANK(50, 8, 0xF4),
> + F7188X_GPIO_BANK(60, 8, 0xF8),
> + F7188X_GPIO_BANK(70, 1, 0xFC),
> +};
> +
> static int f7188x_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
> {
> int err;
> @@ -264,13 +294,16 @@ static int f7188x_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
> err = superio_enter(sio->addr);
> if (err)
> return err;
> - superio_select(sio->addr, SIO_LD_GPIO);
> + superio_select(sio->addr, sio->device);
>
> dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
>
> superio_exit(sio->addr);
>
> - if (dir & 1 << offset)
> + if (gpio_dir_invert(sio->type))
> + dir = ~dir;
> +
> + if (dir & BIT(offset))
> return GPIO_LINE_DIRECTION_OUT;
>
> return GPIO_LINE_DIRECTION_IN;
> @@ -286,10 +319,14 @@ static int f7188x_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
> err = superio_enter(sio->addr);
> if (err)
> return err;
> - superio_select(sio->addr, SIO_LD_GPIO);
> + superio_select(sio->addr, sio->device);
>
> dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
> - dir &= ~BIT(offset);
> +
> + if (gpio_dir_invert(sio->type))
> + dir |= BIT(offset);
> + else
> + dir &= ~BIT(offset);
> superio_outb(sio->addr, gpio_dir(bank->regbase), dir);
>
> superio_exit(sio->addr);
> @@ -307,11 +344,11 @@ static int f7188x_gpio_get(struct gpio_chip *chip, unsigned offset)
> err = superio_enter(sio->addr);
> if (err)
> return err;
> - superio_select(sio->addr, SIO_LD_GPIO);
> + superio_select(sio->addr, sio->device);
>
> dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
> dir = !!(dir & BIT(offset));
> - if (dir)
> + if (gpio_data_single(sio->type) || dir)
> data = superio_inb(sio->addr, gpio_data_out(bank->regbase));
> else
> data = superio_inb(sio->addr, gpio_data_in(bank->regbase));
> @@ -332,7 +369,7 @@ static int f7188x_gpio_direction_out(struct gpio_chip *chip,
> err = superio_enter(sio->addr);
> if (err)
> return err;
> - superio_select(sio->addr, SIO_LD_GPIO);
> + superio_select(sio->addr, sio->device);
>
> data_out = superio_inb(sio->addr, gpio_data_out(bank->regbase));
> if (value)
> @@ -342,7 +379,10 @@ static int f7188x_gpio_direction_out(struct gpio_chip *chip,
> superio_outb(sio->addr, gpio_data_out(bank->regbase), data_out);
>
> dir = superio_inb(sio->addr, gpio_dir(bank->regbase));
> - dir |= BIT(offset);
> + if (gpio_dir_invert(sio->type))
> + dir &= ~BIT(offset);
> + else
> + dir |= BIT(offset);
> superio_outb(sio->addr, gpio_dir(bank->regbase), dir);
>
> superio_exit(sio->addr);
> @@ -360,7 +400,7 @@ static void f7188x_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
> err = superio_enter(sio->addr);
> if (err)
> return;
> - superio_select(sio->addr, SIO_LD_GPIO);
> + superio_select(sio->addr, sio->device);
>
> data_out = superio_inb(sio->addr, gpio_data_out(bank->regbase));
> if (value)
> @@ -388,7 +428,7 @@ static int f7188x_gpio_set_config(struct gpio_chip *chip, unsigned offset,
> err = superio_enter(sio->addr);
> if (err)
> return err;
> - superio_select(sio->addr, SIO_LD_GPIO);
> + superio_select(sio->addr, sio->device);
>
> data = superio_inb(sio->addr, gpio_out_mode(bank->regbase));
> if (param == PIN_CONFIG_DRIVE_OPEN_DRAIN)
> @@ -449,6 +489,10 @@ static int f7188x_gpio_probe(struct platform_device *pdev)
> data->nr_bank = ARRAY_SIZE(f81865_gpio_bank);
> data->bank = f81865_gpio_bank;
> break;
> + case nct6116d:
> + data->nr_bank = ARRAY_SIZE(nct6116d_gpio_bank);
> + data->bank = nct6116d_gpio_bank;
> + break;
> default:
> return -ENODEV;
> }
> @@ -479,18 +523,15 @@ static int __init f7188x_find(int addr, struct f7188x_sio *sio)
> {
> int err;
> u16 devid;
> + u16 manid;
>
> err = superio_enter(addr);
> if (err)
> return err;
>
> err = -ENODEV;
> - devid = superio_inw(addr, SIO_MANID);
> - if (devid != SIO_FINTEK_ID) {
> - pr_debug(DRVNAME ": Not a Fintek device at 0x%08x\n", addr);
> - goto err;
> - }
>
> + sio->device = SIO_LD_GPIO_FINTEK;
> devid = superio_inw(addr, SIO_DEVID);
> switch (devid) {
> case SIO_F71869_ID:
> @@ -517,17 +558,32 @@ static int __init f7188x_find(int addr, struct f7188x_sio *sio)
> case SIO_F81865_ID:
> sio->type = f81865;
> break;
> + case SIO_NCT6116D_ID:
> + sio->device = SIO_LD_GPIO_NUVOTON;
> + sio->type = nct6116d;
> + break;
> default:
> - pr_info(DRVNAME ": Unsupported Fintek device 0x%04x\n", devid);
> + pr_info(DRVNAME ": Unsupported device 0x%04x\n", devid);
> goto err;
> }
> +
> + /* double check manufacturer where possible */
> + if (sio->type != nct6116d) {
> + manid = superio_inw(addr, SIO_FINTEK_MANID);
> + if (manid != SIO_FINTEK_ID) {
> + pr_debug(DRVNAME ": Not a Fintek device at 0x%08x\n", addr);
> + goto err;
> + }
> + }
> +
> sio->addr = addr;
> err = 0;
>
> - pr_info(DRVNAME ": Found %s at %#x, revision %d\n",
> + pr_info(DRVNAME ": Found %s at %#x\n",
> f7188x_names[sio->type],
> - (unsigned int) addr,
> - (int) superio_inb(addr, SIO_DEVREV));
> + (unsigned int)addr);
> + if (sio->type != nct6116d)
> + pr_info(DRVNAME ": revision %d\n", superio_inb(addr, SIO_FINTEK_DEVREV));
>
> err:
> superio_exit(addr);
> --
> 2.35.1
Am Wed, 24 Aug 2022 18:59:17 +0300
schrieb Andy Shevchenko <[email protected]>:
> On Wed, Aug 24, 2022 at 5:04 PM Henning Schild
> <[email protected]> wrote:
> >
> > Add GPIO support for Nuvoton NCT6116 chip. Nuvoton SuperIO chips are
> > very similar to the ones from Fintek. In other subsystems they also
> > share drivers and are called a family of drivers.
> >
> > For the GPIO subsystem the only difference is that the direction
> > bit is reversed and that there is only one data bit per pin. On the
> > SuperIO level the logical device is another one.
> >
> > On a chip level we do not have a manufacturer ID to check and also
> > no revision.
>
> ...
>
> > +#define gpio_dir_invert(type) ((type) == nct6116d)
> > +#define gpio_data_single(type) ((type) == nct6116d)
>
> What you are trying to do here is to put GPIO maintainers / heavy
> contributors on a minefield (basically moving your job to their
> shoulders). Please, provide a proper namespace and not gpio_ one. I'm
> talking in my "GPIO heavy contributor" hat on.
No i was trying to avoid having to touch those other 4 existing macros,
touching lines that checkpatch.pl and you will pick on again. Adding
the prefixes just to those new ones would be inconsistent and also not
nice.
> With that fixed I can survive w/o pr_fmt() being in this patch. If you
> are going to address this, you may add my tag in a new version.
It is a bit unfortunate that you seem to be surprised where i said i
was going to not address this. And once the new series comes insist on
another round ... which involves testing and what not.
But hey, i will send a v6 with style refactoring patches and test it
all over again.
Thanks everyone for the review, i hope that next version will be
acceptable and not open new discussion with the new patches coming.
regards,
Henning
On Thu, Aug 25, 2022 at 12:32 PM Henning Schild
<[email protected]> wrote:
> Am Wed, 24 Aug 2022 18:59:17 +0300
> schrieb Andy Shevchenko <[email protected]>:
> > On Wed, Aug 24, 2022 at 5:04 PM Henning Schild
> > <[email protected]> wrote:
...
> > > +#define gpio_dir_invert(type) ((type) == nct6116d)
> > > +#define gpio_data_single(type) ((type) == nct6116d)
> >
> > What you are trying to do here is to put GPIO maintainers / heavy
> > contributors on a minefield (basically moving your job to their
> > shoulders). Please, provide a proper namespace and not gpio_ one. I'm
> > talking in my "GPIO heavy contributor" hat on.
>
> No i was trying to avoid having to touch those other 4 existing macros,
> touching lines that checkpatch.pl and you will pick on again. Adding
> the prefixes just to those new ones would be inconsistent and also not
> nice.
Do you have other prefixes in those files starting with gpio_?!
Now I see it. I'm not sure why this pops up only now.
> > With that fixed I can survive w/o pr_fmt() being in this patch. If you
> > are going to address this, you may add my tag in a new version.
>
> It is a bit unfortunate that you seem to be surprised where i said i
> was going to not address this.
Yes, because you are not a newbie and you know that the community
doesn't work on a "take it or leave" basis.
> And once the new series comes insist on
> another round ... which involves testing and what not.
Which is your job as a developer.
> But hey, i will send a v6 with style refactoring patches and test it
> all over again.
Thanks!
> Thanks everyone for the review, i hope that next version will be
> acceptable and not open new discussion with the new patches coming.
--
With Best Regards,
Andy Shevchenko