Hey all,
Some 6.1 targeted changes here.
Firstly, two new dev kits (one first-party & one from Aries Embedded).
They've been sitting in our vendor tree, so are being sent where they
belong.
Secondly, another release of our reference design for the Icicle kit
is due in September. Usually these do not really change much for the
devicetree, but this time around a pair of changes impact the memory
map.
The first of these is adding dma-ranges to the pcie controller. The
controller had some issues to begin with & with the current reference
design (v2022.05) would not work with mainline Linux nor has it since
reference design v2021.08. A combination of the property, a change
to the FPGA design & a small fix to the driver will get it working
with mainline again. The other non-backwards compatible change to the
reference design is moves of the peripherals instantiated in the
fabric. Currently they are fairly spread out & a common complaint has
been that this leaves little room in the fic3 section of the memory map
for custom peripherals without removing the existing ones.
This series depends on [0] so as not to add dtbs_check warnings. The
fabric clock support is added by [1].
Thanks,
Conor.
Changes since v2:
- drop the sd & emmc versions of the aries devicetree
- remove a extra newline
Changes since v1:
- made the polarberry part of an enum in patch 1
0 - https://lore.kernel.org/linux-gpio/[email protected]/
1 - https://lore.kernel.org/linux-clk/[email protected]/
Conor Dooley (7):
dt-bindings: riscv: microchip: document icicle reference design
dt-bindings: riscv: microchip: document the aries m100pfsevp
riscv: dts: microchip: add pci dma ranges for the icicle kit
riscv: dts: microchip: move the mpfs' pci node to -fabric.dtsi
riscv: dts: microchip: icicle: update pci address properties
riscv: dts: microchip: icicle: re-jig fabric peripheral addresses
riscv: dts: microchip: add a devicetree for aries' m100pfsevp
Shravan Chippa (1):
dt-bindings: riscv: microchip: document the sev kit
Vattipalli Praveen (1):
riscv: dts: microchip: add sevkit device tree
.../devicetree/bindings/riscv/microchip.yaml | 20 +-
arch/riscv/boot/dts/microchip/Makefile | 2 +
.../dts/microchip/mpfs-icicle-kit-fabric.dtsi | 42 +++-
.../boot/dts/microchip/mpfs-icicle-kit.dts | 3 +-
.../dts/microchip/mpfs-m100pfs-fabric.dtsi | 45 +++++
.../boot/dts/microchip/mpfs-m100pfsevp.dts | 179 ++++++++++++++++++
.../dts/microchip/mpfs-polarberry-fabric.dtsi | 29 +++
.../dts/microchip/mpfs-sev-kit-fabric.dtsi | 45 +++++
.../riscv/boot/dts/microchip/mpfs-sev-kit.dts | 145 ++++++++++++++
arch/riscv/boot/dts/microchip/mpfs.dtsi | 29 ---
10 files changed, 498 insertions(+), 41 deletions(-)
create mode 100644 arch/riscv/boot/dts/microchip/mpfs-m100pfs-fabric.dtsi
create mode 100644 arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts
create mode 100644 arch/riscv/boot/dts/microchip/mpfs-sev-kit-fabric.dtsi
create mode 100644 arch/riscv/boot/dts/microchip/mpfs-sev-kit.dts
--
2.36.1
Add a compatible for the Aries Embedded M100PFSEVP SOM + EVK platform.
Link: https://www.aries-embedded.com/polarfire-soc-fpga-microsemi-m100pfs-som-mpfs025t-pcie-serdes
Signed-off-by: Conor Dooley <[email protected]>
---
Documentation/devicetree/bindings/riscv/microchip.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/riscv/microchip.yaml b/Documentation/devicetree/bindings/riscv/microchip.yaml
index 485981fbfb4b..630f82c85a0c 100644
--- a/Documentation/devicetree/bindings/riscv/microchip.yaml
+++ b/Documentation/devicetree/bindings/riscv/microchip.yaml
@@ -27,6 +27,7 @@ properties:
- items:
- enum:
+ - aries,m100pfsevp
- sundance,polarberry
- const: microchip,mpfs
--
2.36.1
The recently removed, accidentally included, "matr0" property was used
in place of a dma-ranges property. The PCI controller is non-functional
with mainline Linux in the v2022.02 or later reference designs and has
not worked without configuration of address-translation since v2021.08.
Add the address translation that will be used by the v2022.09 reference
design & update the compatible used by the dts.
Signed-off-by: Conor Dooley <[email protected]>
---
arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi | 7 ++++++-
arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts | 3 ++-
2 files changed, 8 insertions(+), 2 deletions(-)
diff --git a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
index 0d28858b83f2..c0fb9dd7b2c8 100644
--- a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
+++ b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
@@ -2,7 +2,8 @@
/* Copyright (c) 2020-2021 Microchip Technology Inc */
/ {
- compatible = "microchip,mpfs-icicle-reference-rtlv2203", "microchip,mpfs";
+ compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit",
+ "microchip,mpfs";
core_pwm0: pwm@41000000 {
compatible = "microchip,corepwm-rtl-v4";
@@ -37,3 +38,7 @@ fabric_clk1: fabric-clk1 {
clock-frequency = <125000000>;
};
};
+
+&pcie {
+ dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 0x1 0x00000000>;
+};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts
index f3f87ed2007f..5e2b8aa2ff64 100644
--- a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts
+++ b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit.dts
@@ -11,7 +11,8 @@
/ {
model = "Microchip PolarFire-SoC Icicle Kit";
- compatible = "microchip,mpfs-icicle-kit", "microchip,mpfs";
+ compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit",
+ "microchip,mpfs";
aliases {
ethernet0 = &mac1;
--
2.36.1
From: Shravan Chippa <[email protected]>
Update devicetree bindings document with PolarFire SoC Video Kit, known
by its "sev-kit" product code.
Link: https://onlinedocs.microchip.com/pr/GUID-404D3738-DC76-46BA-8683-6A77E837C2DD-en-US-1/index.html?GUID-065AEBEE-7B2C-4895-8579-B1D73D797F06
Signed-off-by: Shravan Chippa <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Conor Dooley <[email protected]>
---
Documentation/devicetree/bindings/riscv/microchip.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/riscv/microchip.yaml b/Documentation/devicetree/bindings/riscv/microchip.yaml
index 630f82c85a0c..ab0a64cd5386 100644
--- a/Documentation/devicetree/bindings/riscv/microchip.yaml
+++ b/Documentation/devicetree/bindings/riscv/microchip.yaml
@@ -28,6 +28,7 @@ properties:
- items:
- enum:
- aries,m100pfsevp
+ - microchip,mpfs-sev-kit
- sundance,polarberry
- const: microchip,mpfs
--
2.36.1
The icicle kit reference design's v2022.09 release,made some changes
to the memory map - including adding the ability to read the fabric
clock controllers via the system controller bus & making the PCI
controller work with upstream Linux.
While the PCI was not working in the v2022.03 design, so nothing is
broken there in terms of backwards compatibility, the fabric clocks
used in the v2022.03 design were chosen by the individual run of the
synthesis tool. In the v2022.09 reference design, the clocks are fixed
to use the "north west" fabric Clock Conditioning Circuitry.
Make use of a new compatible to denote that this is not backwards
compatible.
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Conor Dooley <[email protected]>
---
.../devicetree/bindings/riscv/microchip.yaml | 18 ++++++++++++------
1 file changed, 12 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/riscv/microchip.yaml b/Documentation/devicetree/bindings/riscv/microchip.yaml
index 1aa7336a9672..485981fbfb4b 100644
--- a/Documentation/devicetree/bindings/riscv/microchip.yaml
+++ b/Documentation/devicetree/bindings/riscv/microchip.yaml
@@ -17,12 +17,18 @@ properties:
$nodename:
const: '/'
compatible:
- items:
- - enum:
- - microchip,mpfs-icicle-kit
- - microchip,mpfs-icicle-reference-rtlv2203
- - sundance,polarberry
- - const: microchip,mpfs
+ oneOf:
+ - items:
+ - enum:
+ - microchip,mpfs-icicle-reference-rtlv2203
+ - microchip,mpfs-icicle-reference-rtlv2209
+ - const: microchip,mpfs-icicle-kit
+ - const: microchip,mpfs
+
+ - items:
+ - enum:
+ - sundance,polarberry
+ - const: microchip,mpfs
additionalProperties: true
--
2.36.1
When users try to add onto the reference design, they find that the
current addresses that peripherals connected to Fabric InterConnect
(FIC) 3 use are restrictive. For the v2022.09 reference design, the
peripherals have been shifted down, leaving more contiguous address
space for their custom IP/peripherals.
Signed-off-by: Conor Dooley <[email protected]>
---
arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
index 32d51c4a5b0c..98f04be0dc6b 100644
--- a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
+++ b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
@@ -6,18 +6,18 @@ / {
compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit",
"microchip,mpfs";
- core_pwm0: pwm@41000000 {
+ core_pwm0: pwm@40000000 {
compatible = "microchip,corepwm-rtl-v4";
- reg = <0x0 0x41000000 0x0 0xF0>;
+ reg = <0x0 0x40000000 0x0 0xF0>;
microchip,sync-update-mask = /bits/ 32 <0>;
#pwm-cells = <2>;
clocks = <&fabric_clk3>;
status = "disabled";
};
- i2c2: i2c@44000000 {
+ i2c2: i2c@40000200 {
compatible = "microchip,corei2c-rtl-v7";
- reg = <0x0 0x44000000 0x0 0x1000>;
+ reg = <0x0 0x40000200 0x0 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&fabric_clk3>;
--
2.36.1
For the v2022.09 reference design the PCI root port's data region has
been moved to FIC1 from FIC0. This is a shorter path, allowing for
higher clock rates and improved through-put. As a result, the address at
which the PCIe's data region appears to the core complex has changed.
The config region's address is unchanged.
As FIC0 is no longer used, its clock can be removed too.
Signed-off-by: Conor Dooley <[email protected]>
---
.../boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi | 11 ++++++-----
1 file changed, 6 insertions(+), 5 deletions(-)
diff --git a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
index a21440c8ee03..32d51c4a5b0c 100644
--- a/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
+++ b/arch/riscv/boot/dts/microchip/mpfs-icicle-kit-fabric.dtsi
@@ -2,6 +2,7 @@
/* Copyright (c) 2020-2021 Microchip Technology Inc */
/ {
+
compatible = "microchip,mpfs-icicle-reference-rtlv2209", "microchip,mpfs-icicle-kit",
"microchip,mpfs";
@@ -38,13 +39,13 @@ fabric_clk1: fabric-clk1 {
clock-frequency = <125000000>;
};
- pcie: pcie@2000000000 {
+ pcie: pcie@3000000000 {
compatible = "microchip,pcie-host-1.0";
#address-cells = <0x3>;
#interrupt-cells = <0x1>;
#size-cells = <0x2>;
device_type = "pci";
- reg = <0x20 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>;
+ reg = <0x30 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>;
reg-names = "cfg", "apb";
bus-range = <0x0 0x7f>;
interrupt-parent = <&plic>;
@@ -54,9 +55,9 @@ pcie: pcie@2000000000 {
<0 0 0 3 &pcie_intc 2>,
<0 0 0 4 &pcie_intc 3>;
interrupt-map-mask = <0 0 0 7>;
- clocks = <&fabric_clk1>, <&fabric_clk1>, <&fabric_clk3>;
- clock-names = "fic0", "fic1", "fic3";
- ranges = <0x3000000 0x0 0x8000000 0x20 0x8000000 0x0 0x80000000>;
+ clocks = <&fabric_clk1>, <&fabric_clk3>;
+ clock-names = "fic1", "fic3";
+ ranges = <0x3000000 0x0 0x8000000 0x30 0x8000000 0x0 0x80000000>;
dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 0x1 0x00000000>;
msi-parent = <&pcie>;
msi-controller;
--
2.36.1
Add device trees for both configs used by the Aries Embedded
M100PFSEVP. The M100OFSEVP consists of a MPFS250T on a SOM,
featuring:
- 2GB DDR4 SDRAM dedicated to the HMS
- 512MB DDR4 SDRAM dedicated to the FPGA
- 32 MB SPI NOR Flash
- 4 GByte eMMC
and a carrier board with:
- 2x Gigabit Ethernet
- USB
- 2x UART
- 2x CAN
- TFT connector
- HSMC extension connector
- 3x PMOD extension connectors
- microSD-card slot
Link: https://www.aries-embedded.com/polarfire-soc-fpga-microsemi-m100pfs-som-mpfs025t-pcie-serdes
Link: https://www.aries-embedded.com/evaluation-kit/fpga/polarfire-microchip-soc-fpga-m100pfsevp-riscv-hsmc-pmod
Link: https://downloads.aries-embedded.de/products/M100PFS/Hardware/M100PFSEVP-Schematics.pdf
Co-developed-by: Wolfgang Grandegger <[email protected]>
Signed-off-by: Wolfgang Grandegger <[email protected]>
Signed-off-by: Conor Dooley <[email protected]>
---
Note to self:
The amount of DDR at 0x10... is probably a fraction of what is actually there.
arch/riscv/boot/dts/microchip/Makefile | 1 +
.../dts/microchip/mpfs-m100pfs-fabric.dtsi | 45 +++++
.../boot/dts/microchip/mpfs-m100pfsevp.dts | 179 ++++++++++++++++++
3 files changed, 225 insertions(+)
create mode 100644 arch/riscv/boot/dts/microchip/mpfs-m100pfs-fabric.dtsi
create mode 100644 arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts
diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
index f18477b2e86d..7427a20934f3 100644
--- a/arch/riscv/boot/dts/microchip/Makefile
+++ b/arch/riscv/boot/dts/microchip/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-icicle-kit.dtb
+dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-m100pfsevp.dtb
dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-polarberry.dtb
dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-sev-kit.dtb
obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/riscv/boot/dts/microchip/mpfs-m100pfs-fabric.dtsi b/arch/riscv/boot/dts/microchip/mpfs-m100pfs-fabric.dtsi
new file mode 100644
index 000000000000..7b9ee13b6a3a
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-m100pfs-fabric.dtsi
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2022 Microchip Technology Inc */
+
+/ {
+ fabric_clk3: fabric-clk3 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <62500000>;
+ };
+
+ fabric_clk1: fabric-clk1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ pcie: pcie@2000000000 {
+ compatible = "microchip,pcie-host-1.0";
+ #address-cells = <0x3>;
+ #interrupt-cells = <0x1>;
+ #size-cells = <0x2>;
+ device_type = "pci";
+ reg = <0x20 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>;
+ reg-names = "cfg", "apb";
+ bus-range = <0x0 0x7f>;
+ interrupt-parent = <&plic>;
+ interrupts = <119>;
+ interrupt-map = <0 0 0 1 &pcie_intc 0>,
+ <0 0 0 2 &pcie_intc 1>,
+ <0 0 0 3 &pcie_intc 2>,
+ <0 0 0 4 &pcie_intc 3>;
+ interrupt-map-mask = <0 0 0 7>;
+ clocks = <&fabric_clk1>, <&fabric_clk1>, <&fabric_clk3>;
+ clock-names = "fic0", "fic1", "fic3";
+ ranges = <0x3000000 0x0 0x8000000 0x20 0x8000000 0x0 0x80000000>;
+ msi-parent = <&pcie>;
+ msi-controller;
+ status = "disabled";
+ pcie_intc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
+};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts b/arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts
new file mode 100644
index 000000000000..184cb36a175e
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-m100pfsevp.dts
@@ -0,0 +1,179 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Original all-in-one devicetree:
+ * Copyright (C) 2021-2022 - Wolfgang Grandegger <[email protected]>
+ * Rewritten to use includes:
+ * Copyright (C) 2022 - Conor Dooley <[email protected]>
+ */
+/dts-v1/;
+
+#include "mpfs.dtsi"
+#include "mpfs-m100pfs-fabric.dtsi"
+
+/* Clock frequency (in Hz) of the rtcclk */
+#define MTIMER_FREQ 1000000
+
+/ {
+ model = "Aries Embedded M100PFEVPS";
+ compatible = "aries,m100pfsevp", "microchip,mpfs";
+
+ aliases {
+ ethernet0 = &mac0;
+ ethernet1 = &mac1;
+ serial0 = &mmuart0;
+ serial1 = &mmuart1;
+ serial2 = &mmuart2;
+ serial3 = &mmuart3;
+ serial4 = &mmuart4;
+ gpio0 = &gpio0;
+ gpio1 = &gpio2;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ cpus {
+ timebase-frequency = <MTIMER_FREQ>;
+ };
+
+ ddrc_cache_lo: memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x0 0x40000000>;
+ };
+ ddrc_cache_hi: memory@1040000000 {
+ device_type = "memory";
+ reg = <0x10 0x40000000 0x0 0x40000000>;
+ };
+};
+
+&can0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&gpio0 {
+ interrupts = <13>, <14>, <15>, <16>,
+ <17>, <18>, <19>, <20>,
+ <21>, <22>, <23>, <24>,
+ <25>, <26>;
+ ngpios = <14>;
+ status = "okay";
+
+ pmic-irq-hog {
+ gpio-hog;
+ gpios = <13 0>;
+ input;
+ };
+
+ /* Set to low for eMMC, high for SD-card */
+ mmc-sel-hog {
+ gpio-hog;
+ gpios = <12 0>;
+ output-high;
+ };
+};
+
+&gpio2 {
+ interrupts = <13>, <14>, <15>, <16>,
+ <17>, <18>, <19>, <20>,
+ <21>, <22>, <23>, <24>,
+ <25>, <26>, <27>, <28>,
+ <29>, <30>, <31>, <32>,
+ <33>, <34>, <35>, <36>,
+ <37>, <38>, <39>, <40>,
+ <41>, <42>, <43>, <44>;
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+ phy-mode = "gmii";
+ phy-handle = <&phy0>;
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&mac1 {
+ status = "okay";
+ phy-mode = "gmii";
+ phy-handle = <&phy1>;
+ phy1: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&mbox {
+ status = "okay";
+};
+
+&mmc {
+ max-frequency = <50000000>;
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ no-1-8-v;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ disable-wp;
+ status = "okay";
+};
+
+&mmuart1 {
+ status = "okay";
+};
+
+&mmuart2 {
+ status = "okay";
+};
+
+&mmuart3 {
+ status = "okay";
+};
+
+&mmuart4 {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&qspi {
+ status = "okay";
+};
+
+&refclk {
+ clock-frequency = <125000000>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+};
+
+&spi1 {
+ status = "okay";
+};
+
+&syscontroller {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "host";
+};
--
2.36.1
From: Vattipalli Praveen <[email protected]>
Add a basic dts for the Microchip Smart Embedded Vision dev kit.
The SEV kit is an upcoming first party board, featuring an MPFS250T and:
- Dual Sony Camera Sensors (IMX334)
- IEEE 802.11 b/g/n 20MHz (1x1) Wi-Fi
- Bluetooth 5 Low Energy
- 4 GB DDR4 x64
- 2 GB LPDDR4 x32
- 1 GB SPI Flash
- 8 GB eMMC flash & SD card slot (multiplexed)
- HDMI2.0 Video Input/Output
- MIPI DSI Output
- MIPI CSI-2 Input
Link: https://onlinedocs.microchip.com/pr/GUID-404D3738-DC76-46BA-8683-6A77E837C2DD-en-US-1/index.html?GUID-065AEBEE-7B2C-4895-8579-B1D73D797F06
Signed-off-by: Vattipalli Praveen <[email protected]>
Signed-off-by: Conor Dooley <[email protected]>
---
arch/riscv/boot/dts/microchip/Makefile | 1 +
.../dts/microchip/mpfs-sev-kit-fabric.dtsi | 45 ++++++
.../riscv/boot/dts/microchip/mpfs-sev-kit.dts | 145 ++++++++++++++++++
3 files changed, 191 insertions(+)
create mode 100644 arch/riscv/boot/dts/microchip/mpfs-sev-kit-fabric.dtsi
create mode 100644 arch/riscv/boot/dts/microchip/mpfs-sev-kit.dts
diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
index 39aae7b04f1c..f18477b2e86d 100644
--- a/arch/riscv/boot/dts/microchip/Makefile
+++ b/arch/riscv/boot/dts/microchip/Makefile
@@ -1,4 +1,5 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-icicle-kit.dtb
dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-polarberry.dtb
+dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += mpfs-sev-kit.dtb
obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/riscv/boot/dts/microchip/mpfs-sev-kit-fabric.dtsi b/arch/riscv/boot/dts/microchip/mpfs-sev-kit-fabric.dtsi
new file mode 100644
index 000000000000..8545baf4d129
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-sev-kit-fabric.dtsi
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2022 Microchip Technology Inc */
+
+/ {
+ fabric_clk3: fabric-clk3 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ fabric_clk1: fabric-clk1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ pcie: pcie@2000000000 {
+ compatible = "microchip,pcie-host-1.0";
+ #address-cells = <0x3>;
+ #interrupt-cells = <0x1>;
+ #size-cells = <0x2>;
+ device_type = "pci";
+ reg = <0x20 0x0 0x0 0x8000000>, <0x0 0x43000000 0x0 0x10000>;
+ reg-names = "cfg", "apb";
+ bus-range = <0x0 0x7f>;
+ interrupt-parent = <&plic>;
+ interrupts = <119>;
+ interrupt-map = <0 0 0 1 &pcie_intc 0>,
+ <0 0 0 2 &pcie_intc 1>,
+ <0 0 0 3 &pcie_intc 2>,
+ <0 0 0 4 &pcie_intc 3>;
+ interrupt-map-mask = <0 0 0 7>;
+ clocks = <&fabric_clk1>, <&fabric_clk1>, <&fabric_clk3>;
+ clock-names = "fic0", "fic1", "fic3";
+ ranges = <0x3000000 0x0 0x8000000 0x20 0x8000000 0x0 0x80000000>;
+ msi-parent = <&pcie>;
+ msi-controller;
+ status = "disabled";
+ pcie_intc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
+};
diff --git a/arch/riscv/boot/dts/microchip/mpfs-sev-kit.dts b/arch/riscv/boot/dts/microchip/mpfs-sev-kit.dts
new file mode 100644
index 000000000000..013cb666c72d
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/mpfs-sev-kit.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2022 Microchip Technology Inc */
+
+/dts-v1/;
+
+#include "mpfs.dtsi"
+#include "mpfs-sev-kit-fabric.dtsi"
+
+/* Clock frequency (in Hz) of the rtcclk */
+#define MTIMER_FREQ 1000000
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ model = "Microchip PolarFire-SoC SEV Kit";
+ compatible = "microchip,mpfs-sev-kit", "microchip,mpfs";
+
+ aliases {
+ ethernet0 = &mac1;
+ serial0 = &mmuart0;
+ serial1 = &mmuart1;
+ serial2 = &mmuart2;
+ serial3 = &mmuart3;
+ serial4 = &mmuart4;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ cpus {
+ timebase-frequency = <MTIMER_FREQ>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ fabricbuf0ddrc: buffer@80000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0x80000000 0x0 0x2000000>;
+ };
+
+ fabricbuf1ddrnc: buffer@c4000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0xc4000000 0x0 0x4000000>;
+ };
+
+ fabricbuf2ddrncwcb: buffer@d4000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x0 0xd4000000 0x0 0x4000000>;
+ };
+ };
+
+ ddrc_cache: memory@1000000000 {
+ device_type = "memory";
+ reg = <0x10 0x0 0x0 0x76000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&gpio2 {
+ interrupts = <53>, <53>, <53>, <53>,
+ <53>, <53>, <53>, <53>,
+ <53>, <53>, <53>, <53>,
+ <53>, <53>, <53>, <53>,
+ <53>, <53>, <53>, <53>,
+ <53>, <53>, <53>, <53>,
+ <53>, <53>, <53>, <53>,
+ <53>, <53>, <53>, <53>;
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&phy0>;
+ phy1: ethernet-phy@9 {
+ reg = <9>;
+ };
+ phy0: ethernet-phy@8 {
+ reg = <8>;
+ };
+};
+
+&mac1 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&phy1>;
+};
+
+&mbox {
+ status = "okay";
+};
+
+&mmc {
+ status = "okay";
+ bus-width = <4>;
+ disable-wp;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+};
+
+&mmuart1 {
+ status = "okay";
+};
+
+&mmuart2 {
+ status = "okay";
+};
+
+&mmuart3 {
+ status = "okay";
+};
+
+&mmuart4 {
+ status = "okay";
+};
+
+&refclk {
+ clock-frequency = <125000000>;
+};
+
+&rtc {
+ status = "okay";
+};
+
+&syscontroller {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "otg";
+};
--
2.36.1
On Thu, 01 Sep 2022 14:33:57 +0100, Conor Dooley wrote:
> Add a compatible for the Aries Embedded M100PFSEVP SOM + EVK platform.
>
> Link: https://www.aries-embedded.com/polarfire-soc-fpga-microsemi-m100pfs-som-mpfs025t-pcie-serdes
> Signed-off-by: Conor Dooley <[email protected]>
> ---
> Documentation/devicetree/bindings/riscv/microchip.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
Acked-by: Rob Herring <[email protected]>