Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.
With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.
This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <[email protected]>
Acked-by: Arun Ramadoss <[email protected]>
---
drivers/net/dsa/microchip/ksz8.h | 1 +
drivers/net/dsa/microchip/ksz8795.c | 53 ++++++++++++++++++++++++-
drivers/net/dsa/microchip/ksz8795_reg.h | 3 ++
drivers/net/dsa/microchip/ksz_common.c | 7 ++++
drivers/net/dsa/microchip/ksz_common.h | 4 ++
5 files changed, 66 insertions(+), 2 deletions(-)
diff --git a/drivers/net/dsa/microchip/ksz8.h b/drivers/net/dsa/microchip/ksz8.h
index 8582b4b67d98..ea05abfbd51d 100644
--- a/drivers/net/dsa/microchip/ksz8.h
+++ b/drivers/net/dsa/microchip/ksz8.h
@@ -57,5 +57,6 @@ int ksz8_reset_switch(struct ksz_device *dev);
int ksz8_switch_detect(struct ksz_device *dev);
int ksz8_switch_init(struct ksz_device *dev);
void ksz8_switch_exit(struct ksz_device *dev);
+int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu);
#endif
diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index bd3b133e7085..d01bfd609130 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -76,6 +76,57 @@ int ksz8_reset_switch(struct ksz_device *dev)
return 0;
}
+static int ksz8863_change_mtu(struct ksz_device *dev, int frame_size)
+{
+ u8 ctrl2 = 0;
+
+ if (frame_size <= KSZ8_LEGAL_PACKET_SIZE)
+ ctrl2 |= KSZ8863_LEGAL_PACKET_ENABLE;
+ else if (frame_size > KSZ8863_NORMAL_PACKET_SIZE)
+ ctrl2 |= KSZ8863_HUGE_PACKET_ENABLE;
+
+ return ksz_rmw8(dev, REG_SW_CTRL_2, KSZ8863_LEGAL_PACKET_ENABLE |
+ KSZ8863_HUGE_PACKET_ENABLE, ctrl2);
+}
+
+static int ksz8795_change_mtu(struct ksz_device *dev, int frame_size)
+{
+ u8 ctrl1 = 0, ctrl2 = 0;
+ int ret;
+
+ if (frame_size > KSZ8_LEGAL_PACKET_SIZE)
+ ctrl2 |= SW_LEGAL_PACKET_DISABLE;
+ else if (frame_size > KSZ8863_NORMAL_PACKET_SIZE)
+ ctrl1 |= SW_HUGE_PACKET;
+
+ ret = ksz_rmw8(dev, REG_SW_CTRL_1, SW_HUGE_PACKET, ctrl1);
+ if (ret)
+ return ret;
+
+ return ksz_rmw8(dev, REG_SW_CTRL_2, SW_LEGAL_PACKET_DISABLE, ctrl2);
+}
+
+int ksz8_change_mtu(struct ksz_device *dev, int port, int mtu)
+{
+ u16 frame_size;
+
+ if (!dsa_is_cpu_port(dev->ds, port))
+ return 0;
+
+ frame_size = mtu + VLAN_ETH_HLEN + ETH_FCS_LEN;
+
+ switch (dev->chip_id) {
+ case KSZ8795_CHIP_ID:
+ case KSZ8794_CHIP_ID:
+ case KSZ8765_CHIP_ID:
+ return ksz8795_change_mtu(dev, frame_size);
+ case KSZ8830_CHIP_ID:
+ return ksz8863_change_mtu(dev, frame_size);
+ }
+
+ return -EOPNOTSUPP;
+}
+
static void ksz8795_set_prio_queue(struct ksz_device *dev, int port, int queue)
{
u8 hi, lo;
@@ -1233,8 +1284,6 @@ void ksz8_config_cpu_port(struct dsa_switch *ds)
masks = dev->info->masks;
regs = dev->info->regs;
- /* Switch marks the maximum frame with extra byte as oversize. */
- ksz_cfg(dev, REG_SW_CTRL_2, SW_LEGAL_PACKET_DISABLE, true);
ksz_cfg(dev, regs[S_TAIL_TAG_CTRL], masks[SW_TAIL_TAG_ENABLE], true);
p = &dev->ports[dev->cpu_port];
diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h b/drivers/net/dsa/microchip/ksz8795_reg.h
index 77487d611824..7a57c6088f80 100644
--- a/drivers/net/dsa/microchip/ksz8795_reg.h
+++ b/drivers/net/dsa/microchip/ksz8795_reg.h
@@ -48,6 +48,9 @@
#define NO_EXC_COLLISION_DROP BIT(3)
#define SW_LEGAL_PACKET_DISABLE BIT(1)
+#define KSZ8863_HUGE_PACKET_ENABLE BIT(2)
+#define KSZ8863_LEGAL_PACKET_ENABLE BIT(1)
+
#define REG_SW_CTRL_3 0x05
#define WEIGHTED_FAIR_QUEUE_ENABLE BIT(3)
diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 49a5a236d958..f39b041765fb 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -172,6 +172,7 @@ static const struct ksz_dev_ops ksz8_dev_ops = {
.reset = ksz8_reset_switch,
.init = ksz8_switch_init,
.exit = ksz8_switch_exit,
+ .change_mtu = ksz8_change_mtu,
};
static void ksz9477_phylink_mac_link_up(struct ksz_device *dev, int port,
@@ -2500,6 +2501,12 @@ static int ksz_max_mtu(struct dsa_switch *ds, int port)
struct ksz_device *dev = ds->priv;
switch (dev->chip_id) {
+ case KSZ8795_CHIP_ID:
+ case KSZ8794_CHIP_ID:
+ case KSZ8765_CHIP_ID:
+ return KSZ8795_HUGE_PACKET_SIZE - VLAN_ETH_HLEN - ETH_FCS_LEN;
+ case KSZ8830_CHIP_ID:
+ return KSZ8863_HUGE_PACKET_SIZE - VLAN_ETH_HLEN - ETH_FCS_LEN;
case KSZ8563_CHIP_ID:
case KSZ9477_CHIP_ID:
case KSZ9563_CHIP_ID:
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index 5f404a444ce1..cb27f5a180c7 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -591,6 +591,10 @@ static inline int is_lan937x(struct ksz_device *dev)
#define PORT_SRC_PHY_INT 1
+#define KSZ8795_HUGE_PACKET_SIZE 2000
+#define KSZ8863_HUGE_PACKET_SIZE 1916
+#define KSZ8863_NORMAL_PACKET_SIZE 1536
+#define KSZ8_LEGAL_PACKET_SIZE 1518
#define KSZ9477_MAX_FRAME_SIZE 9000
/* Regmap tables generation */
--
2.30.2
On Thu, Nov 10, 2022 at 01:22:25PM +0100, Oleksij Rempel wrote:
> Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
>
> Before this patch, pre-configured behavior was different on different
> switch series, due to opposite meaning of the same bit:
> - KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
> - KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
>
> Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
> assume, the idea was to set max frame size to 1532.
>
> With this patch, by setting MTU size 1500, both switch series will be
> configured to the 1532 frame limit.
>
> This patch was tested on KSZ8873.
>
> Signed-off-by: Oleksij Rempel <[email protected]>
> Acked-by: Arun Ramadoss <[email protected]>
> ---
Reviewed-by: Vladimir Oltean <[email protected]>
As an extension to this patch set, you might also want to set
ds->mtu_enforcement_ingress = true, to activate the bridge MTU
normalization logic, since you have one MTU global to the entire switch.
On 11/10/2022 4:22 AM, Oleksij Rempel wrote:
> Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
>
> Before this patch, pre-configured behavior was different on different
> switch series, due to opposite meaning of the same bit:
> - KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
> - KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
>
> Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
> assume, the idea was to set max frame size to 1532.
>
> With this patch, by setting MTU size 1500, both switch series will be
> configured to the 1532 frame limit.
>
> This patch was tested on KSZ8873.
>
> Signed-off-by: Oleksij Rempel <[email protected]>
> Acked-by: Arun Ramadoss <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
--
Florian
On Thu, Nov 10, 2022 at 03:03:25PM +0200, Vladimir Oltean wrote:
> On Thu, Nov 10, 2022 at 01:22:25PM +0100, Oleksij Rempel wrote:
> > Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
> >
> > Before this patch, pre-configured behavior was different on different
> > switch series, due to opposite meaning of the same bit:
> > - KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
> > - KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
> >
> > Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
> > assume, the idea was to set max frame size to 1532.
> >
> > With this patch, by setting MTU size 1500, both switch series will be
> > configured to the 1532 frame limit.
> >
> > This patch was tested on KSZ8873.
> >
> > Signed-off-by: Oleksij Rempel <[email protected]>
> > Acked-by: Arun Ramadoss <[email protected]>
> > ---
>
> Reviewed-by: Vladimir Oltean <[email protected]>
>
> As an extension to this patch set, you might also want to set
> ds->mtu_enforcement_ingress = true, to activate the bridge MTU
> normalization logic, since you have one MTU global to the entire switch.
Ok, I'll include it in to a different patch set. There are more patches
to mainline :)
Regards,
Oleksij
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |