From: Frank Wunderlich <[email protected]>
This Series adds some Nodes to mt7986 devicetree and the BananaPi R3
This version is rebased on Matthias' DTS64 next Branch from 2022/11/11.
i included sams series for mt7986 DTS with small changes
https://patchwork.kernel.org/project/linux-mediatek/cover/20220427124741.18245->
6.2 will support dtso extension for dt overlays:
"kbuild: Allow DTB overlays to built from .dtso named source files"
https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2
There is some discussion about inclusion of dt-overlays and if it is
better to support mmc also by these:
https://patchwork.kernel.org/comment/25092116/
https://patchwork.kernel.org/comment/25085681/
i had run full dtbs-check but i end up with some strange warnings in
ethernet-node that should not come up as phy-handle and sfp/managed
properties are already defined.
phy-handle made optional
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/mediatek,net.yaml#n265
property sfp/managed (which is included for mac subnode in yaml above):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-controller.yaml#n137
changes:
v6:
- dropped regulators from usb-patch as suggested by chunfeng yun
- moved 3v3 regulator to mmc-patch as it is needed for emmc to work
rfbs were tested by sam shih, r3 by me
- dropped RB from AngeloGioacchino from mmc-patch due to this change
- fixed links in coverletter which were broken in v5
- i hope this series is sent without errors now (my mailprovider limited
mails last 2 times while sending part 10)
v5:
- changed usb ranges/reg/unit-adress
- added reviewd-by's except usb-part due to changes
v4:
- dropped RFC prefix
- rebase on matthias' mtk dts-next (for 6.2) branch
- added author information to overlays
- fixed sfp binding error
- added fix for moving wed_pcie node
- readded missing compatible patches
v3:
- changed mmc pull-ups
- added patch for board binding (sent separately before)
- added pcie node in mt7986 (not yet again in r3)
- added dt overlays
Frank Wunderlich (7):
arm64: dts: mt7986: move wed_pcie node
dt-bindings: phy: mediatek,tphy: add support for mt7986
dt-bindings: usb: mtk-xhci: add support for mt7986
dt-bindings: PCI: mediatek-gen3: add SoC based clock config
dt-bindings: PCI: mediatek-gen3: add support for mt7986
arm64: dts: mt7986: add Bananapi R3
arm64: dts: mt7986: add BPI-R3 nand/nor overlays
Sam Shih (4):
arm64: dts: mt7986: add spi related device nodes
arm64: dts: mt7986: add usb related device nodes
arm64: dts: mt7986: add mmc related device nodes
arm64: dts: mt7986: add pcie related device nodes
.../bindings/pci/mediatek-pcie-gen3.yaml | 64 ++-
.../bindings/phy/mediatek,tphy.yaml | 1 +
.../bindings/usb/mediatek,mtk-xhci.yaml | 1 +
arch/arm64/boot/dts/mediatek/Makefile | 4 +
.../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts | 31 ++
.../mediatek/mt7986a-bananapi-bpi-r3-nand.dts | 55 +++
.../mediatek/mt7986a-bananapi-bpi-r3-nor.dts | 69 +++
.../mediatek/mt7986a-bananapi-bpi-r3-sd.dts | 25 +
.../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 446 ++++++++++++++++++
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 155 ++++++
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 162 ++++++-
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 43 ++
12 files changed, 1038 insertions(+), 18 deletions(-)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
--
2.34.1
From: Sam Shih <[email protected]>
This patch adds PCIe support for MT7986.
Signed-off-by: Jieyy Yang <[email protected]>
Signed-off-by: Sam Shih <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
changes compared to sams original version:
- add clock-names to pcie node
- update clocks to new binding
---
bindings-patches:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=690172
---
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 16 ++++++
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 52 ++++++++++++++++++++
2 files changed, 68 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 4c0b879d6703..8eaee9ff1822 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -93,6 +93,15 @@ &mmc0 {
non-removable;
no-sd;
no-sdio;
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pins>;
+ status = "okay";
+};
+
+&pcie_phy {
status = "okay";
};
@@ -155,6 +164,13 @@ conf-rst {
};
};
+ pcie_pins: pcie-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+ };
+ };
+
spi_flash_pins: spi-flash-pins {
mux {
function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index b3ad8978b563..b310abc02dcc 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/mt7986-clk.h>
#include <dt-bindings/reset/mt7986-resets.h>
+#include <dt-bindings/phy/phy.h>
/ {
interrupt-parent = <&gic>;
@@ -319,6 +320,57 @@ mmc0: mmc@11230000 {
status = "disabled";
};
+ pcie: pcie@11280000 {
+ compatible = "mediatek,mt7986-pcie",
+ "mediatek,mt8192-pcie";
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ reg = <0x00 0x11280000 0x00 0x4000>;
+ reg-names = "pcie-mac";
+ interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+ bus-range = <0x00 0xff>;
+ ranges = <0x82000000 0x00 0x20000000 0x00
+ 0x20000000 0x00 0x10000000>;
+ clocks = <&infracfg CLK_INFRA_IPCIE_PIPE_CK>,
+ <&infracfg CLK_INFRA_IPCIE_CK>,
+ <&infracfg CLK_INFRA_IPCIER_CK>,
+ <&infracfg CLK_INFRA_IPCIEB_CK>;
+ clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m";
+ status = "disabled";
+
+ phys = <&pcie_port PHY_TYPE_PCIE>;
+ phy-names = "pcie-phy";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &pcie_intc 0>,
+ <0 0 0 2 &pcie_intc 1>,
+ <0 0 0 3 &pcie_intc 2>,
+ <0 0 0 4 &pcie_intc 3>;
+ pcie_intc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+ };
+
+ pcie_phy: t-phy@11c00000 {
+ compatible = "mediatek,mt7986-tphy",
+ "mediatek,generic-tphy-v2";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ pcie_port: pcie-phy@11c00000 {
+ reg = <0 0x11c00000 0 0x20000>;
+ clocks = <&clk40m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ };
+ };
+
usb_phy: t-phy@11e10000 {
compatible = "mediatek,mt7986-tphy",
"mediatek,generic-tphy-v2";
--
2.34.1
From: Frank Wunderlich <[email protected]>
Add compatible string for mt7986.
Signed-off-by: Frank Wunderlich <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Chunfeng Yun <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
index 939623867a64..a3c37944c630 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -28,6 +28,7 @@ properties:
- mediatek,mt7622-xhci
- mediatek,mt7623-xhci
- mediatek,mt7629-xhci
+ - mediatek,mt7986-xhci
- mediatek,mt8173-xhci
- mediatek,mt8183-xhci
- mediatek,mt8186-xhci
--
2.34.1
From: Frank Wunderlich <[email protected]>
Add compatible string and clock-definition for mt7986. It needs 4 clocks
for PCIe, define them in binding.
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Jianjun Wang <[email protected]>
---
v2:
- squashed patch 2+3 (compatible and clock definition)
---
.../bindings/pci/mediatek-pcie-gen3.yaml | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
index 5d7369debff2..f7a02019daea 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
@@ -48,6 +48,7 @@ properties:
oneOf:
- items:
- enum:
+ - mediatek,mt7986-pcie
- mediatek,mt8188-pcie
- mediatek,mt8195-pcie
- const: mediatek,mt8192-pcie
@@ -78,9 +79,11 @@ properties:
- const: mac
clocks:
+ minItems: 4
maxItems: 6
clock-names:
+ minItems: 4
maxItems: 6
assigned-clocks:
@@ -160,6 +163,20 @@ allOf:
- const: tl_32k
- const: peri_26m
- const: peri_mem
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - mediatek,mt7986-pcie
+ then:
+ properties:
+ clock-names:
+ items:
+ - const: pl_250m
+ - const: tl_26m
+ - const: peri_26m
+ - const: top_133m
unevaluatedProperties: false
--
2.34.1
From: Frank Wunderlich <[email protected]>
Add support for Bananapi R3 SBC.
- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
The device can boot from all 4 storage options. Both, SPI and MMC, can
be switched using hardware switches on the board, see
https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting
I have added base dtb for sd/emmc to have a bootable version in mainline
linux. SPI-NAND/NOR switched (CS by sw5/C) can be done with DT-Overlays,
but don't know how to do it in upstream the right way...added dts files
for dtbo and added them with dtbo extension to Makefile works.
there is a commit which adds support building dtso files to dtbo in next:
"kbuild: Allow DTB overlays to built from .dtso named source files"
https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2
if Overlays are accepted then we can change my current dts from here
to overlays too to have all as such. Till then imho the best way is to
have mmc as board dts and add the right spi-device via overlay if
needed.
changes:
v6:
- drop usb 5v regulator from bpi-r3
based on chunfengs response it is only needed if regulator is
switched (like for otg), usb works without it.
v4:
- add PCIe nodes
- fix sfp-properties of sfp-1 (need to be plural)
thx to Denis Odintsov for this
v3:
- rename factory-key to reset-key
- add dcin regulator and add it as input for 3v3 (with renaming)
- remove memory-node
- dropped wifi eeprom (calibration) data
- move mmc0 pinctrl to common dtsi and drop sdcard comment
- change mmc pull-up/down to have generic bias-pull*
v2:
- remove pcie to be added later (discussion about clocks)
- some fixes based on suggestions on ML
- add key suffix like it's done in mt7622-bpi-r64 devicetree
- add dash in sfp node names
- use reg as unit for switch-node
- drop "-3-4" suffix from i2c-pins node name
- fix order in Makefile
---
arch/arm64/boot/dts/mediatek/Makefile | 2 +
.../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts | 31 ++
.../mediatek/mt7986a-bananapi-bpi-r3-sd.dts | 25 +
.../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 446 ++++++++++++++++++
4 files changed, 504 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 0ec90cb3ef28..e8902f2cc58f 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -7,6 +7,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
new file mode 100644
index 000000000000..a0ca35b5977e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7986a-bananapi-bpi-r3.dtsi"
+
+/ {
+ model = "Bananapi BPI-R3 (emmc)";
+};
+
+&mmc0 {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ hs400-ds-delay = <0x14014>;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
new file mode 100644
index 000000000000..06e4691cb815
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <[email protected]>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7986a-bananapi-bpi-r3.dtsi"
+
+/ {
+ model = "Bananapi BPI-R3 (sdmmc)";
+};
+
+&mmc0 {
+ bus-width = <4>;
+ max-frequency = <52000000>;
+ cap-sd-highspeed;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
new file mode 100644
index 000000000000..455e958ea08a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Sam.Shih <[email protected]>
+ * Frank Wunderlich <[email protected]>
+ * Daniel Golle <[email protected]>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+ model = "Bananapi BPI-R3";
+ compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ dcin: regulator-12vd {
+ compatible = "regulator-fixed";
+ regulator-name = "12vd";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset-key {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ wps-key {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ /* i2c of the left SFP cage (wan) */
+ i2c_sfp1: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ /* i2c of the right SFP cage (lan) */
+ i2c_sfp2: i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ green_led: led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ blue_led: led-1 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ reg_1p8v: regulator-1p8v {
+ compatible = "regulator-fixed";
+ regulator-name = "1.8vd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ vin-supply = <&dcin>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3.3vd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ vin-supply = <&dcin>;
+ };
+
+ /* left SFP cage (wan) */
+ sfp1: sfp-1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* right SFP cage (lan) */
+ sfp2: sfp-2 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac@0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac@1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "2500base-x";
+ sfp = <&sfp1>;
+ managed = "in-band-status";
+ };
+
+ mdio: mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&mdio {
+ switch: switch@31 {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_pins_default>;
+ pinctrl-1 = <&mmc0_pins_uhs>;
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_pins>;
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pins>;
+ status = "okay";
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pio {
+ i2c_pins: i2c-pins {
+ mux {
+ function = "i2c";
+ groups = "i2c";
+ };
+ };
+
+ mmc0_pins_default: mmc0-pins {
+ mux {
+ function = "emmc";
+ groups = "emmc_51";
+ };
+ conf-cmd-dat {
+ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ conf-clk {
+ pins = "EMMC_CK";
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-ds {
+ pins = "EMMC_DSL";
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-rst {
+ pins = "EMMC_RSTB";
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ };
+
+ mmc0_pins_uhs: mmc0-uhs-pins {
+ mux {
+ function = "emmc";
+ groups = "emmc_51";
+ };
+ conf-cmd-dat {
+ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ conf-clk {
+ pins = "EMMC_CK";
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-ds {
+ pins = "EMMC_DSL";
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-rst {
+ pins = "EMMC_RSTB";
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ };
+
+ pcie_pins: pcie-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie_clk", "pcie_pereset";
+ };
+ };
+
+ spi_flash_pins: spi-flash-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ };
+
+ spic_pins: spic-pins {
+ mux {
+ function = "spi";
+ groups = "spi1_0";
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ mux {
+ function = "uart";
+ groups = "uart1_rx_tx";
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ mux {
+ function = "uart";
+ groups = "uart2_0_rx_tx";
+ };
+ };
+
+ wf_2g_5g_pins: wf-2g-5g-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_2g", "wf_5g";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <4>;
+ };
+ };
+
+ wf_dbdc_pins: wf-dbdc-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_dbdc";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <4>;
+ };
+ };
+
+ wf_led_pins: wf-led-pins {
+ mux {
+ function = "led";
+ groups = "wifi_led";
+ };
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ cs-gpios = <0>, <0>;
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic_pins>;
+ cs-gpios = <0>, <0>;
+ status = "okay";
+};
+
+&ssusb {
+ status = "okay";
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "wan";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan0";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan1";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan2";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan3";
+ };
+
+ port5: port@5 {
+ reg = <5>;
+ label = "lan4";
+ phy-mode = "2500base-x";
+ sfp = <&sfp2>;
+ managed = "in-band-status";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&trng {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+ pinctrl-names = "default", "dbdc";
+ pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+ pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+};
+
--
2.34.1
From: Frank Wunderlich <[email protected]>
Move the wed_pcie node to have node aligned by address.
Fixes: 00b9903996b3 ("arm64: dts: mediatek: mt7986: add support for Wireless Ethernet Dispatch")
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index a22e10e89ab9..afc01abfa99c 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -112,6 +112,12 @@ infracfg: infracfg@10001000 {
#clock-cells = <1>;
};
+ wed_pcie: wed-pcie@10003000 {
+ compatible = "mediatek,mt7986-wed-pcie",
+ "syscon";
+ reg = <0 0x10003000 0 0x10>;
+ };
+
topckgen: topckgen@1001b000 {
compatible = "mediatek,mt7986-topckgen", "syscon";
reg = <0 0x1001B000 0 0x1000>;
@@ -257,12 +263,6 @@ ethsys: syscon@15000000 {
#reset-cells = <1>;
};
- wed_pcie: wed-pcie@10003000 {
- compatible = "mediatek,mt7986-wed-pcie",
- "syscon";
- reg = <0 0x10003000 0 0x10>;
- };
-
wed0: wed@15010000 {
compatible = "mediatek,mt7986-wed",
"syscon";
--
2.34.1
From: Frank Wunderlich <[email protected]>
Add compatible string for mt7986.
Signed-off-by: Frank Wunderlich <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Chunfeng Yun <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
index 5613cc5106e3..230a17f24966 100644
--- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -79,6 +79,7 @@ properties:
- enum:
- mediatek,mt2712-tphy
- mediatek,mt7629-tphy
+ - mediatek,mt7986-tphy
- mediatek,mt8183-tphy
- mediatek,mt8186-tphy
- mediatek,mt8192-tphy
--
2.34.1
From: Sam Shih <[email protected]>
This patch adds spi support for MT7986.
Signed-off-by: Sam Shih <[email protected]>
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 35 ++++++++++++++++++++
arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 28 ++++++++++++++++
arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 35 ++++++++++++++++++++
3 files changed, 98 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 2f48cc3d3ddb..006878e3f2b2 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -59,6 +59,20 @@ switch: switch@0 {
};
&pio {
+ spi_flash_pins: spi-flash-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ };
+
+ spic_pins: spic-pins {
+ mux {
+ function = "spi";
+ groups = "spi1_2";
+ };
+ };
+
uart1_pins: uart1-pins {
mux {
function = "uart";
@@ -105,6 +119,27 @@ conf {
};
};
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ cs-gpios = <0>, <0>;
+ status = "okay";
+ spi_nand: spi_nand@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+ };
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic_pins>;
+ cs-gpios = <0>, <0>;
+ status = "okay";
+};
+
&switch {
ports {
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index afc01abfa99c..29da9b8ed753 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -253,6 +253,34 @@ i2c0: i2c@11008000 {
status = "disabled";
};
+ spi0: spi@1100a000 {
+ compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0 0x1100a000 0 0x100>;
+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&topckgen CLK_TOP_MPLL_D2>,
+ <&topckgen CLK_TOP_SPI_SEL>,
+ <&infracfg CLK_INFRA_SPI0_CK>,
+ <&infracfg CLK_INFRA_SPI0_HCK_CK>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk";
+ status = "disabled";
+ };
+
+ spi1: spi@1100b000 {
+ compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0 0x1100b000 0 0x100>;
+ interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&topckgen CLK_TOP_MPLL_D2>,
+ <&topckgen CLK_TOP_SPIM_MST_SEL>,
+ <&infracfg CLK_INFRA_SPI1_CK>,
+ <&infracfg CLK_INFRA_SPI1_HCK_CK>;
+ clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk";
+ status = "disabled";
+ };
+
ethsys: syscon@15000000 {
#address-cells = <1>;
#size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 79c5c78f7a14..2c7f1d4fb352 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -100,6 +100,20 @@ fixed-link {
};
&pio {
+ spi_flash_pins: spi-flash-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ };
+
+ spic_pins: spic-pins {
+ mux {
+ function = "spi";
+ groups = "spi1_2";
+ };
+ };
+
wf_2g_5g_pins: wf-2g-5g-pins {
mux {
function = "wifi";
@@ -132,6 +146,27 @@ conf {
};
};
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ cs-gpios = <0>, <0>;
+ status = "okay";
+ spi_nand: spi_nand@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+ };
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spic_pins>;
+ cs-gpios = <0>, <0>;
+ status = "okay";
+};
+
&uart0 {
status = "okay";
};
--
2.34.1
On 18/11/2022 20:01, Frank Wunderlich wrote:
> From: Frank Wunderlich <[email protected]>
>
> Add compatible string for mt7986.
>
> Signed-off-by: Frank Wunderlich <[email protected]>
> Acked-by: Krzysztof Kozlowski <[email protected]>
> Reviewed-by: Chunfeng Yun <[email protected]>
> Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
> ---
> Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
> index 5613cc5106e3..230a17f24966 100644
> --- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
> +++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
> @@ -79,6 +79,7 @@ properties:
> - enum:
> - mediatek,mt2712-tphy
> - mediatek,mt7629-tphy
> + - mediatek,mt7986-tphy
> - mediatek,mt8183-tphy
> - mediatek,mt8186-tphy
> - mediatek,mt8192-tphy
On 18/11/2022 20:01, Frank Wunderlich wrote:
> From: Frank Wunderlich <[email protected]>
>
> Add compatible string for mt7986.
>
> Signed-off-by: Frank Wunderlich <[email protected]>
> Acked-by: Krzysztof Kozlowski <[email protected]>
> Reviewed-by: Chunfeng Yun <[email protected]>
> Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
> ---
> Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> index 939623867a64..a3c37944c630 100644
> --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
> @@ -28,6 +28,7 @@ properties:
> - mediatek,mt7622-xhci
> - mediatek,mt7623-xhci
> - mediatek,mt7629-xhci
> + - mediatek,mt7986-xhci
> - mediatek,mt8173-xhci
> - mediatek,mt8183-xhci
> - mediatek,mt8186-xhci
On 18/11/2022 20:01, Frank Wunderlich wrote:
> From: Frank Wunderlich <[email protected]>
>
> Add compatible string and clock-definition for mt7986. It needs 4 clocks
> for PCIe, define them in binding.
>
> Signed-off-by: Frank Wunderlich <[email protected]>
> Reviewed-by: Rob Herring <[email protected]>
> Acked-by: Jianjun Wang <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
> ---
> v2:
> - squashed patch 2+3 (compatible and clock definition)
> ---
> .../bindings/pci/mediatek-pcie-gen3.yaml | 17 +++++++++++++++++
> 1 file changed, 17 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
> index 5d7369debff2..f7a02019daea 100644
> --- a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
> +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
> @@ -48,6 +48,7 @@ properties:
> oneOf:
> - items:
> - enum:
> + - mediatek,mt7986-pcie
> - mediatek,mt8188-pcie
> - mediatek,mt8195-pcie
> - const: mediatek,mt8192-pcie
> @@ -78,9 +79,11 @@ properties:
> - const: mac
>
> clocks:
> + minItems: 4
> maxItems: 6
>
> clock-names:
> + minItems: 4
> maxItems: 6
>
> assigned-clocks:
> @@ -160,6 +163,20 @@ allOf:
> - const: tl_32k
> - const: peri_26m
> - const: peri_mem
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - mediatek,mt7986-pcie
> + then:
> + properties:
> + clock-names:
> + items:
> + - const: pl_250m
> + - const: tl_26m
> + - const: peri_26m
> + - const: top_133m
>
> unevaluatedProperties: false
>
On 18/11/2022 20:01, Frank Wunderlich wrote:
> From: Sam Shih <[email protected]>
>
> This patch adds spi support for MT7986.
>
> Signed-off-by: Sam Shih <[email protected]>
> Signed-off-by: Frank Wunderlich <[email protected]>
> Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Applied, thanks!
> ---
> arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 35 ++++++++++++++++++++
> arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 28 ++++++++++++++++
> arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 35 ++++++++++++++++++++
> 3 files changed, 98 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> index 2f48cc3d3ddb..006878e3f2b2 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> @@ -59,6 +59,20 @@ switch: switch@0 {
> };
>
> &pio {
> + spi_flash_pins: spi-flash-pins {
> + mux {
> + function = "spi";
> + groups = "spi0", "spi0_wp_hold";
> + };
> + };
> +
> + spic_pins: spic-pins {
> + mux {
> + function = "spi";
> + groups = "spi1_2";
> + };
> + };
> +
> uart1_pins: uart1-pins {
> mux {
> function = "uart";
> @@ -105,6 +119,27 @@ conf {
> };
> };
>
> +&spi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_flash_pins>;
> + cs-gpios = <0>, <0>;
> + status = "okay";
> + spi_nand: spi_nand@0 {
> + compatible = "spi-nand";
> + reg = <0>;
> + spi-max-frequency = <10000000>;
> + spi-tx-buswidth = <4>;
> + spi-rx-buswidth = <4>;
> + };
> +};
> +
> +&spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spic_pins>;
> + cs-gpios = <0>, <0>;
> + status = "okay";
> +};
> +
> &switch {
> ports {
> #address-cells = <1>;
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> index afc01abfa99c..29da9b8ed753 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> @@ -253,6 +253,34 @@ i2c0: i2c@11008000 {
> status = "disabled";
> };
>
> + spi0: spi@1100a000 {
> + compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0 0x1100a000 0 0x100>;
> + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&topckgen CLK_TOP_MPLL_D2>,
> + <&topckgen CLK_TOP_SPI_SEL>,
> + <&infracfg CLK_INFRA_SPI0_CK>,
> + <&infracfg CLK_INFRA_SPI0_HCK_CK>;
> + clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk";
> + status = "disabled";
> + };
> +
> + spi1: spi@1100b000 {
> + compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0 0x1100b000 0 0x100>;
> + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&topckgen CLK_TOP_MPLL_D2>,
> + <&topckgen CLK_TOP_SPIM_MST_SEL>,
> + <&infracfg CLK_INFRA_SPI1_CK>,
> + <&infracfg CLK_INFRA_SPI1_HCK_CK>;
> + clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk";
> + status = "disabled";
> + };
> +
> ethsys: syscon@15000000 {
> #address-cells = <1>;
> #size-cells = <1>;
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> index 79c5c78f7a14..2c7f1d4fb352 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> @@ -100,6 +100,20 @@ fixed-link {
> };
>
> &pio {
> + spi_flash_pins: spi-flash-pins {
> + mux {
> + function = "spi";
> + groups = "spi0", "spi0_wp_hold";
> + };
> + };
> +
> + spic_pins: spic-pins {
> + mux {
> + function = "spi";
> + groups = "spi1_2";
> + };
> + };
> +
> wf_2g_5g_pins: wf-2g-5g-pins {
> mux {
> function = "wifi";
> @@ -132,6 +146,27 @@ conf {
> };
> };
>
> +&spi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_flash_pins>;
> + cs-gpios = <0>, <0>;
> + status = "okay";
> + spi_nand: spi_nand@0 {
> + compatible = "spi-nand";
> + reg = <0>;
> + spi-max-frequency = <10000000>;
> + spi-tx-buswidth = <4>;
> + spi-rx-buswidth = <4>;
> + };
> +};
> +
> +&spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spic_pins>;
> + cs-gpios = <0>, <0>;
> + status = "okay";
> +};
> +
> &uart0 {
> status = "okay";
> };
On 18/11/2022 20:01, Frank Wunderlich wrote:
> From: Frank Wunderlich <[email protected]>
>
> Move the wed_pcie node to have node aligned by address.
>
> Fixes: 00b9903996b3 ("arm64: dts: mediatek: mt7986: add support for Wireless Ethernet Dispatch")
> Signed-off-by: Frank Wunderlich <[email protected]>
> Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Applied, thanks!
> ---
> arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 12 ++++++------
> 1 file changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> index a22e10e89ab9..afc01abfa99c 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> @@ -112,6 +112,12 @@ infracfg: infracfg@10001000 {
> #clock-cells = <1>;
> };
>
> + wed_pcie: wed-pcie@10003000 {
> + compatible = "mediatek,mt7986-wed-pcie",
> + "syscon";
> + reg = <0 0x10003000 0 0x10>;
> + };
> +
> topckgen: topckgen@1001b000 {
> compatible = "mediatek,mt7986-topckgen", "syscon";
> reg = <0 0x1001B000 0 0x1000>;
> @@ -257,12 +263,6 @@ ethsys: syscon@15000000 {
> #reset-cells = <1>;
> };
>
> - wed_pcie: wed-pcie@10003000 {
> - compatible = "mediatek,mt7986-wed-pcie",
> - "syscon";
> - reg = <0 0x10003000 0 0x10>;
> - };
> -
> wed0: wed@15010000 {
> compatible = "mediatek,mt7986-wed",
> "syscon";