v4: Sort properties in l11.
v3: Set property status = "okay"; as the last property.
Reword the bindings patch.
v2: Fix a typo in dt-bindings commit message
Acer Iconia Talk S A1-724 is a tablet using the MSM8916 SoC released
in 2014.
Note: The original firmware from Acer can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Acer
didn't set up (firmware) secure boot.
Add a device tree for with initial support for:
- GPIO keys
- pm8916-vibrator
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- WCNSS (WiFi/BT)
- Regulators
- Bosch BMC150 accelerometer/magnetometer
Document the new acer,a1-724 device tree bindings used in its device tree.
Signed-off-by: Lin, Meng-Bo <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 463509f0f23a..83f6748979a9 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -180,6 +180,7 @@ properties:
- items:
- enum:
+ - acer,a1-724
- alcatel,idol347
- asus,z00l
- huawei,g7
--
2.30.2
Iconia Talk S uses a Bosch BMC150 accelerometer/magnetometer combo.
The chip provides two separate I2C devices for the accelerometer
and magnetometer that are already supported by the bmc150-accel
and bmc150-magn driver.
Signed-off-by: Lin, Meng-Bo <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
---
.../boot/dts/qcom/msm8916-acer-a1-724.dts | 38 +++++++++++++++++++
1 file changed, 38 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
index 593051ea92b6..bea0d022dd9a 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
@@ -6,6 +6,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/*
* NOTE: The original firmware from Acer can only boot 32-bit kernels.
@@ -51,6 +52,35 @@ usb_id: usb-id {
};
};
+&blsp_i2c2 {
+ status = "okay";
+
+ accelerometer@10 {
+ compatible = "bosch,bmc150_accel";
+ reg = <0x10>;
+ interrupt-parent = <&msmgpio>;
+ interrupts = <115 IRQ_TYPE_EDGE_RISING>;
+
+ vdd-supply = <&pm8916_l17>;
+ vddio-supply = <&pm8916_l6>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_int_default>;
+
+ mount-matrix = "0", "-1", "0",
+ "-1", "0", "0",
+ "0", "0", "1";
+ };
+
+ magnetometer@12 {
+ compatible = "bosch,bmc150_magn";
+ reg = <0x12>;
+
+ vdd-supply = <&pm8916_l17>;
+ vddio-supply = <&pm8916_l6>;
+ };
+};
+
&blsp1_uart2 {
status = "okay";
};
@@ -199,6 +229,14 @@ l18 {
};
&msmgpio {
+ accel_int_default: accel-int-default-state {
+ pins = "gpio115";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
gpio_keys_default: gpio-keys-default-state {
pins = "gpio107";
function = "gpio";
--
2.30.2
v5: Add touchscreen.
v4: Sort properties in l11.
v3: Set property status = "okay"; as the last property.
Reword the bindings patch.
v2: Fix a typo in dt-bindings commit message
Acer Iconia Talk S A1-724 is a tablet using the MSM8916 SoC released
in 2014.
Note: The original firmware from Acer can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Acer
didn't set up (firmware) secure boot.
Add a device tree for with initial support for:
- GPIO keys
- pm8916-vibrator
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- WCNSS (WiFi/BT)
- Regulators
- Bosch BMC150 accelerometer/magnetometer
- Focaltech FT5446 touchscreen
Acer Iconia Talk S A1-724 is a tablet using the MSM8916 SoC released
in 2014.
Note: The original firmware from Acer can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Acer
didn't set up (firmware) secure boot.
Add a device tree for with initial support for:
- GPIO keys
- pm8916-vibrator
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- WCNSS (WiFi/BT)
- Regulators
Signed-off-by: Lin, Meng-Bo <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/msm8916-acer-a1-724.dts | 217 ++++++++++++++++++
2 files changed, 218 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index afe496a93f94..f38a20074013 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c2.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-huawei-g7.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
new file mode 100644
index 000000000000..593051ea92b6
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/*
+ * NOTE: The original firmware from Acer can only boot 32-bit kernels.
+ * To boot this device tree using arm64 it is necessary to flash 64-bit
+ * TZ/HYP firmware (e.g. taken from the DragonBoard 410c).
+ * See https://wiki.postmarketos.org/wiki/Acer_Iconia_Talk_S_(acer-a1-724)
+ * for suggested installation instructions.
+ */
+
+/ {
+ model = "Acer Iconia Talk S A1-724";
+ compatible = "acer,a1-724", "qcom,msm8916";
+ chassis-type = "tablet";
+
+ aliases {
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_keys_default>;
+
+ label = "GPIO Buttons";
+
+ button-volume-up {
+ label = "Volume Up";
+ gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ usb_id: usb-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_id_default>;
+ };
+};
+
+&blsp1_uart2 {
+ status = "okay";
+};
+
+&pm8916_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&pm8916_vib {
+ status = "okay";
+};
+
+&pronto {
+ status = "okay";
+};
+
+&sdhc_1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+ pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
+
+ cd-gpios = <&msmgpio 38 GPIO_ACTIVE_HIGH>;
+
+ status = "okay";
+};
+
+&usb {
+ extcon = <&usb_id>, <&usb_id>;
+ status = "okay";
+};
+
+&usb_hs_phy {
+ extcon = <&usb_id>;
+};
+
+&smd_rpm_regulators {
+ vdd_l1_l2_l3-supply = <&pm8916_s3>;
+ vdd_l4_l5_l6-supply = <&pm8916_s4>;
+ vdd_l7-supply = <&pm8916_s4>;
+
+ s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l8 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l10 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-system-load = <200000>;
+ regulator-allow-set-load;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l13 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+};
+
+&msmgpio {
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio107";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ usb_id_default: usb-id-default-state {
+ pins = "gpio110";
+ function = "gpio";
+
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
--
2.30.2
A1-724 uses a Focaltech FT5446 touchscreen that is connected to blsp_i2c5.
Add it to the device tree.
Signed-off-by: Lin, Meng-Bo <[email protected]>
---
.../boot/dts/qcom/msm8916-acer-a1-724.dts | 42 +++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
index bea0d022dd9a..5b216107f69b 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
@@ -81,6 +81,30 @@ magnetometer@12 {
};
};
+&blsp_i2c5 {
+ status = "okay";
+
+ touchscreen@38 {
+ /* Actually ft5446 */
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&msmgpio 12 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&pm8916_l16>;
+ iovcc-supply = <&pm8916_l6>;
+
+ touchscreen-size-x = <720>;
+ touchscreen-size-y = <1280>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_default>;
+ };
+};
+
&blsp1_uart2 {
status = "okay";
};
@@ -245,6 +269,24 @@ gpio_keys_default: gpio-keys-default-state {
bias-pull-up;
};
+ touchscreen_default: touchscreen-default-state {
+ reset-pins {
+ pins = "gpio12";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ touchscreen-pins {
+ pins = "gpio13";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
usb_id_default: usb-id-default-state {
pins = "gpio110";
function = "gpio";
--
2.30.2
Document the new acer,a1-724 device tree bindings used in its device tree.
Signed-off-by: Lin, Meng-Bo <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 463509f0f23a..83f6748979a9 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -180,6 +180,7 @@ properties:
- items:
- enum:
+ - acer,a1-724
- alcatel,idol347
- asus,z00l
- huawei,g7
--
2.30.2
Iconia Talk S uses a Bosch BMC150 accelerometer/magnetometer combo.
The chip provides two separate I2C devices for the accelerometer
and magnetometer that are already supported by the bmc150-accel
and bmc150-magn driver.
Signed-off-by: Lin, Meng-Bo <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
---
.../boot/dts/qcom/msm8916-acer-a1-724.dts | 38 +++++++++++++++++++
1 file changed, 38 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
index 593051ea92b6..bea0d022dd9a 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
@@ -6,6 +6,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/*
* NOTE: The original firmware from Acer can only boot 32-bit kernels.
@@ -51,6 +52,35 @@ usb_id: usb-id {
};
};
+&blsp_i2c2 {
+ status = "okay";
+
+ accelerometer@10 {
+ compatible = "bosch,bmc150_accel";
+ reg = <0x10>;
+ interrupt-parent = <&msmgpio>;
+ interrupts = <115 IRQ_TYPE_EDGE_RISING>;
+
+ vdd-supply = <&pm8916_l17>;
+ vddio-supply = <&pm8916_l6>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&accel_int_default>;
+
+ mount-matrix = "0", "-1", "0",
+ "-1", "0", "0",
+ "0", "0", "1";
+ };
+
+ magnetometer@12 {
+ compatible = "bosch,bmc150_magn";
+ reg = <0x12>;
+
+ vdd-supply = <&pm8916_l17>;
+ vddio-supply = <&pm8916_l6>;
+ };
+};
+
&blsp1_uart2 {
status = "okay";
};
@@ -199,6 +229,14 @@ l18 {
};
&msmgpio {
+ accel_int_default: accel-int-default-state {
+ pins = "gpio115";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
gpio_keys_default: gpio-keys-default-state {
pins = "gpio107";
function = "gpio";
--
2.30.2
On 22/11/2022 14:25, Lin, Meng-Bo wrote:
> A1-724 uses a Focaltech FT5446 touchscreen that is connected to blsp_i2c5.
> Add it to the device tree.
Subject prefix needs fixes (reversed).
Best regards,
Krzysztof