Some of MediaTek's Filogic SoCs come with built-in gigabit Ethernet
PHYs which require calibration data from the SoC's efuse.
Despite the similar design the driver doesn't share any code with the
existing mediatek-ge.c, so add support for these PHYs by introducing a
new driver for only MediaTek's ARM64 SoCs.
Signed-off-by: Daniel Golle <[email protected]>
---
Changes since v1:
* split-off SoC-specific driver from mediatek-ge.c as requested
* address comments made by Heiner Kallweit
* add pinctrl handling for PHY LED
* remove calibration details not needed in production hardware
MAINTAINERS | 9 +
drivers/net/phy/Kconfig | 12 +
drivers/net/phy/Makefile | 1 +
drivers/net/phy/mediatek-ge-soc.c | 1263 +++++++++++++++++++++++++++++
drivers/net/phy/mediatek-ge.c | 3 +-
5 files changed, 1287 insertions(+), 1 deletion(-)
create mode 100644 drivers/net/phy/mediatek-ge-soc.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 6ac562e0381e0..c8307ac6174a8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13078,6 +13078,15 @@ S: Maintained
F: drivers/net/pcs/pcs-mtk-lynxi.c
F: include/linux/pcs/pcs-mtk-lynxi.h
+MEDIATEK ETHERNET PHY DRIVERS
+M: Daniel Golle <[email protected]>
+M: Qingfang Deng <[email protected]>
+M: SkyLake Huang <[email protected]>
+L: [email protected]
+S: Maintained
+F: drivers/net/phy/mediatek-ge-soc.c
+F: drivers/net/phy/mediatek-ge.c
+
MEDIATEK I2C CONTROLLER DRIVER
M: Qii Wang <[email protected]>
L: [email protected]
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index bcfba077b80e1..1cf7ee655f1ce 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -238,6 +238,18 @@ config MEDIATEK_GE_PHY
help
Supports the MediaTek Gigabit Ethernet PHYs.
+config MEDIATEK_GE_SOC_PHY
+ tristate "MediaTek SoC Ethernet PHYs"
+ depends on (ARM64 && ARCH_MEDIATEK) || COMPILE_TEST
+ select NVMEM_MTK_EFUSE
+ help
+ Supports MediaTek SoC built-in Gigabit Ethernet PHYs.
+
+ Include support for built-in Ethernet PHYs which are present in
+ the MT7981 and MT7988 SoCs. These PHYs need calibration data
+ present in the SoCs efuse and will dynamically calibrate VCM
+ (common-mode voltage) during startup.
+
config MICREL_PHY
tristate "Micrel PHYs"
depends on PTP_1588_CLOCK_OPTIONAL
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index ae11bf20b46ee..212fc32f03261 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -69,6 +69,7 @@ obj-$(CONFIG_MARVELL_PHY) += marvell.o
obj-$(CONFIG_MARVELL_88X2222_PHY) += marvell-88x2222.o
obj-$(CONFIG_MAXLINEAR_GPHY) += mxl-gpy.o
obj-$(CONFIG_MEDIATEK_GE_PHY) += mediatek-ge.o
+obj-$(CONFIG_MEDIATEK_GE_SOC_PHY) += mediatek-ge-soc.o
obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o
obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o
obj-$(CONFIG_MICREL_PHY) += micrel.o
diff --git a/drivers/net/phy/mediatek-ge-soc.c b/drivers/net/phy/mediatek-ge-soc.c
new file mode 100644
index 0000000000000..e48502ac3fdd1
--- /dev/null
+++ b/drivers/net/phy/mediatek-ge-soc.c
@@ -0,0 +1,1263 @@
+// SPDX-License-Identifier: GPL-2.0+
+#include <linux/bitfield.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/phy.h>
+
+#define MTK_GPHY_ID_MT7981 0x03a29461
+#define MTK_GPHY_ID_MT7988 0x03a29481
+
+#define MTK_EXT_PAGE_ACCESS 0x1f
+#define MTK_PHY_PAGE_STANDARD 0x0000
+#define MTK_PHY_PAGE_EXTENDED_3 0x0003
+
+#define MTK_PHY_LPI_REG_14 0x14
+#define MTK_PHY_LPI_WAKE_TIMER_1000_MASK GENMASK(8, 0)
+
+#define MTK_PHY_LPI_REG_1c 0x1c
+#define MTK_PHY_SMI_DET_ON_THRESH_MASK GENMASK(13, 8)
+
+#define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30
+#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5
+
+#define ANALOG_INTERNAL_OPERATION_MAX_US 20
+#define TXRESERVE_MIN 0
+#define TXRESERVE_MAX 7
+
+#define MTK_PHY_ANARG_RG 0x10
+#define MTK_PHY_TCLKOFFSET_MASK GENMASK(12, 8)
+
+/* Registers on MDIO_MMD_VEND1 */
+#define MTK_PHY_TXVLD_DA_RG 0x12
+#define MTK_PHY_DA_TX_I2MPB_A_GBE_MASK GENMASK(15, 10)
+#define MTK_PHY_DA_TX_I2MPB_A_TBT_MASK GENMASK(5, 0)
+
+#define MTK_PHY_TX_I2MPB_TEST_MODE_A2 0x16
+#define MTK_PHY_DA_TX_I2MPB_A_HBT_MASK GENMASK(15, 10)
+#define MTK_PHY_DA_TX_I2MPB_A_TST_MASK GENMASK(5, 0)
+
+#define MTK_PHY_TX_I2MPB_TEST_MODE_B1 0x17
+#define MTK_PHY_DA_TX_I2MPB_B_GBE_MASK GENMASK(13, 8)
+#define MTK_PHY_DA_TX_I2MPB_B_TBT_MASK GENMASK(5, 0)
+
+#define MTK_PHY_TX_I2MPB_TEST_MODE_B2 0x18
+#define MTK_PHY_DA_TX_I2MPB_B_HBT_MASK GENMASK(13, 8)
+#define MTK_PHY_DA_TX_I2MPB_B_TST_MASK GENMASK(5, 0)
+
+#define MTK_PHY_TX_I2MPB_TEST_MODE_C1 0x19
+#define MTK_PHY_DA_TX_I2MPB_C_GBE_MASK GENMASK(13, 8)
+#define MTK_PHY_DA_TX_I2MPB_C_TBT_MASK GENMASK(5, 0)
+
+#define MTK_PHY_TX_I2MPB_TEST_MODE_C2 0x20
+#define MTK_PHY_DA_TX_I2MPB_C_HBT_MASK GENMASK(13, 8)
+#define MTK_PHY_DA_TX_I2MPB_C_TST_MASK GENMASK(5, 0)
+
+#define MTK_PHY_TX_I2MPB_TEST_MODE_D1 0x21
+#define MTK_PHY_DA_TX_I2MPB_D_GBE_MASK GENMASK(13, 8)
+#define MTK_PHY_DA_TX_I2MPB_D_TBT_MASK GENMASK(5, 0)
+
+#define MTK_PHY_TX_I2MPB_TEST_MODE_D2 0x22
+#define MTK_PHY_DA_TX_I2MPB_D_HBT_MASK GENMASK(13, 8)
+#define MTK_PHY_DA_TX_I2MPB_D_TST_MASK GENMASK(5, 0)
+
+#define MTK_PHY_RXADC_CTRL_RG7 0xc6
+#define MTK_PHY_DA_AD_BUF_BIAS_LP_MASK GENMASK(9, 8)
+
+#define MTK_PHY_RXADC_CTRL_RG9 0xc8
+#define MTK_PHY_DA_RX_PSBN_TBT_MASK GENMASK(14, 12)
+#define MTK_PHY_DA_RX_PSBN_HBT_MASK GENMASK(10, 8)
+#define MTK_PHY_DA_RX_PSBN_GBE_MASK GENMASK(6, 4)
+#define MTK_PHY_DA_RX_PSBN_LP_MASK GENMASK(2, 0)
+
+#define MTK_PHY_LDO_OUTPUT_V 0xd7
+
+#define MTK_PHY_RG_ANA_CAL_RG0 0xdb
+#define MTK_PHY_RG_CAL_CKINV BIT(12)
+#define MTK_PHY_RG_ANA_CALEN BIT(8)
+#define MTK_PHY_RG_ZCALEN_A BIT(0)
+
+#define MTK_PHY_RG_ANA_CAL_RG1 0xdc
+#define MTK_PHY_RG_ZCALEN_B BIT(12)
+#define MTK_PHY_RG_ZCALEN_C BIT(8)
+#define MTK_PHY_RG_ZCALEN_D BIT(4)
+#define MTK_PHY_RG_TXVOS_CALEN BIT(0)
+
+#define MTK_PHY_RG_ANA_CAL_RG5 0xe0
+#define MTK_PHY_RG_REXT_TRIM_MASK GENMASK(13, 8)
+
+#define MTK_PHY_RG_TX_FILTER 0xfe
+
+#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG120 0x120
+#define MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK GENMASK(12, 8)
+#define MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK GENMASK(4, 0)
+
+#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122 0x122
+#define MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK GENMASK(7, 0)
+
+#define MTK_PHY_RG_TESTMUX_ADC_CTRL 0x144
+#define MTK_PHY_RG_TXEN_DIG_MASK GENMASK(5, 5)
+
+#define MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B 0x172
+#define MTK_PHY_CR_TX_AMP_OFFSET_A_MASK GENMASK(13, 8)
+#define MTK_PHY_CR_TX_AMP_OFFSET_B_MASK GENMASK(6, 0)
+
+#define MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D 0x173
+#define MTK_PHY_CR_TX_AMP_OFFSET_C_MASK GENMASK(13, 8)
+#define MTK_PHY_CR_TX_AMP_OFFSET_D_MASK GENMASK(6, 0)
+
+#define MTK_PHY_RG_AD_CAL_COMP 0x17a
+#define MTK_PHY_AD_CAL_COMP_OUT_SHIFT (8)
+
+#define MTK_PHY_RG_AD_CAL_CLK 0x17b
+#define MTK_PHY_DA_CAL_CLK BIT(0)
+
+#define MTK_PHY_RG_AD_CALIN 0x17c
+#define MTK_PHY_DA_CALIN_FLAG BIT(0)
+
+#define MTK_PHY_RG_DASN_DAC_IN0_A 0x17d
+#define MTK_PHY_DASN_DAC_IN0_A_MASK GENMASK(9, 0)
+
+#define MTK_PHY_RG_DASN_DAC_IN0_B 0x17e
+#define MTK_PHY_DASN_DAC_IN0_B_MASK GENMASK(9, 0)
+
+#define MTK_PHY_RG_DASN_DAC_IN0_C 0x17f
+#define MTK_PHY_DASN_DAC_IN0_C_MASK GENMASK(9, 0)
+
+#define MTK_PHY_RG_DASN_DAC_IN0_D 0x180
+#define MTK_PHY_DASN_DAC_IN0_D_MASK GENMASK(9, 0)
+
+#define MTK_PHY_RG_DASN_DAC_IN1_A 0x181
+#define MTK_PHY_DASN_DAC_IN1_A_MASK GENMASK(9, 0)
+
+#define MTK_PHY_RG_DASN_DAC_IN1_B 0x182
+#define MTK_PHY_DASN_DAC_IN1_B_MASK GENMASK(9, 0)
+
+#define MTK_PHY_RG_DASN_DAC_IN1_C 0x183
+#define MTK_PHY_DASN_DAC_IN1_C_MASK GENMASK(9, 0)
+
+#define MTK_PHY_RG_DASN_DAC_IN1_D 0x184
+#define MTK_PHY_DASN_DAC_IN1_D_MASK GENMASK(9, 0)
+
+#define MTK_PHY_RG_DEV1E_REG19b 0x19b
+#define MTK_PHY_BYPASS_DSP_LPI_READY BIT(8)
+
+#define MTK_PHY_RG_LP_IIR2_K1_L 0x22a
+#define MTK_PHY_RG_LP_IIR2_K1_U 0x22b
+#define MTK_PHY_RG_LP_IIR2_K2_L 0x22c
+#define MTK_PHY_RG_LP_IIR2_K2_U 0x22d
+#define MTK_PHY_RG_LP_IIR2_K3_L 0x22e
+#define MTK_PHY_RG_LP_IIR2_K3_U 0x22f
+#define MTK_PHY_RG_LP_IIR2_K4_L 0x230
+#define MTK_PHY_RG_LP_IIR2_K4_U 0x231
+#define MTK_PHY_RG_LP_IIR2_K5_L 0x232
+#define MTK_PHY_RG_LP_IIR2_K5_U 0x233
+
+#define MTK_PHY_RG_DEV1E_REG234 0x234
+#define MTK_PHY_TR_OPEN_LOOP_EN_MASK GENMASK(0, 0)
+#define MTK_PHY_LPF_X_AVERAGE_MASK GENMASK(7, 4)
+#define MTK_PHY_TR_LP_IIR_EEE_EN BIT(12)
+
+#define MTK_PHY_RG_LPF_CNT_VAL 0x235
+
+#define MTK_PHY_RG_DEV1E_REG238 0x238
+#define MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK GENMASK(8, 0)
+#define MTK_PHY_LPI_SLV_SEND_TX_EN BIT(12)
+
+#define MTK_PHY_RG_DEV1E_REG239 0x239
+#define MTK_PHY_LPI_SEND_LOC_TIMER_MASK GENMASK(8, 0)
+#define MTK_PHY_LPI_TXPCS_LOC_RCV BIT(12)
+
+#define MTK_PHY_RG_DEV1E_REG27C 0x27c
+#define MTK_PHY_VGASTATE_FFE_THR_ST1_MASK GENMASK(12, 8)
+#define MTK_PHY_RG_DEV1E_REG27D 0x27d
+#define MTK_PHY_VGASTATE_FFE_THR_ST2_MASK GENMASK(4, 0)
+
+#define MTK_PHY_RG_DEV1E_REG2C7 0x2c7
+#define MTK_PHY_MAX_GAIN_MASK GENMASK(4, 0)
+#define MTK_PHY_MIN_GAIN_MASK GENMASK(12, 8)
+
+#define MTK_PHY_RG_DEV1E_REG2D1 0x2d1
+#define MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK GENMASK(7, 0)
+#define MTK_PHY_LPI_SKIP_SD_SLV_TR BIT(8)
+#define MTK_PHY_LPI_TR_READY BIT(9)
+#define MTK_PHY_LPI_VCO_EEE_STG0_EN BIT(10)
+
+#define MTK_PHY_RG_DEV1E_REG323 0x323
+#define MTK_PHY_EEE_WAKE_MAS_INT_DC BIT(0)
+#define MTK_PHY_EEE_WAKE_SLV_INT_DC BIT(4)
+
+#define MTK_PHY_RG_DEV1E_REG324 0x324
+#define MTK_PHY_SMI_DETCNT_MAX_MASK GENMASK(5, 0)
+#define MTK_PHY_SMI_DET_MAX_EN BIT(8)
+
+#define MTK_PHY_RG_DEV1E_REG326 0x326
+#define MTK_PHY_LPI_MODE_SD_ON BIT(0)
+#define MTK_PHY_RESET_RANDUPD_CNT BIT(1)
+#define MTK_PHY_TREC_UPDATE_ENAB_CLR BIT(2)
+#define MTK_PHY_LPI_QUIT_WAIT_DFE_SIG_DET_OFF BIT(4)
+#define MTK_PHY_TR_READY_SKIP_AFE_WAKEUP BIT(5)
+
+#define MTK_PHY_LDO_PUMP_EN_PAIRAB 0x502
+#define MTK_PHY_LDO_PUMP_EN_PAIRCD 0x503
+
+#define MTK_PHY_DA_TX_R50_PAIR_A 0x53d
+#define MTK_PHY_DA_TX_R50_PAIR_B 0x53e
+#define MTK_PHY_DA_TX_R50_PAIR_C 0x53f
+#define MTK_PHY_DA_TX_R50_PAIR_D 0x540
+
+/* Registers on MDIO_MMD_VEND2 */
+#define MTK_PHY_LED0_ON_CTRL 0x24
+#define MTK_PHY_LED0_ON_MASK GENMASK(6, 0)
+#define MTK_PHY_LED0_ON_LINK1000 BIT(0)
+#define MTK_PHY_LED0_ON_LINK100 BIT(1)
+#define MTK_PHY_LED0_ON_LINK10 BIT(2)
+#define MTK_PHY_LED0_ON_LINKDOWN BIT(3)
+#define MTK_PHY_LED0_ON_FDX BIT(4) /* Full duplex */
+#define MTK_PHY_LED0_ON_HDX BIT(5) /* Half duplex */
+#define MTK_PHY_LED0_FORCE_ON BIT(6)
+#define MTK_PHY_LED0_POLARITY BIT(14)
+#define MTK_PHY_LED0_ENABLE BIT(15)
+
+#define MTK_PHY_LED0_BLINK_CTRL 0x25
+#define MTK_PHY_LED0_1000TX BIT(0)
+#define MTK_PHY_LED0_1000RX BIT(1)
+#define MTK_PHY_LED0_100TX BIT(2)
+#define MTK_PHY_LED0_100RX BIT(3)
+#define MTK_PHY_LED0_10TX BIT(4)
+#define MTK_PHY_LED0_10RX BIT(5)
+#define MTK_PHY_LED0_COLLISION BIT(6)
+#define MTK_PHY_LED0_RX_CRC_ERR BIT(7)
+#define MTK_PHY_LED0_RX_IDLE_ERR BIT(8)
+#define MTK_PHY_LED0_FORCE_BLINK BIT(9)
+
+#define MTK_PHY_LED1_ON_CTRL 0x26
+#define MTK_PHY_LED1_ON_MASK GENMASK(6, 0)
+#define MTK_PHY_LED1_ON_LINK1000 BIT(0)
+#define MTK_PHY_LED1_ON_LINK100 BIT(1)
+#define MTK_PHY_LED1_ON_LINK10 BIT(2)
+#define MTK_PHY_LED1_ON_LINKDOWN BIT(3)
+#define MTK_PHY_LED1_ON_FDX BIT(4) /* Full duplex */
+#define MTK_PHY_LED1_ON_HDX BIT(5) /* Half duplex */
+#define MTK_PHY_LED1_FORCE_ON BIT(6)
+#define MTK_PHY_LED1_POLARITY BIT(14)
+#define MTK_PHY_LED1_ENABLE BIT(15)
+
+#define MTK_PHY_LED1_BLINK_CTRL 0x27
+#define MTK_PHY_LED1_1000TX BIT(0)
+#define MTK_PHY_LED1_1000RX BIT(1)
+#define MTK_PHY_LED1_100TX BIT(2)
+#define MTK_PHY_LED1_100RX BIT(3)
+#define MTK_PHY_LED1_10TX BIT(4)
+#define MTK_PHY_LED1_10RX BIT(5)
+#define MTK_PHY_LED1_COLLISION BIT(6)
+#define MTK_PHY_LED1_RX_CRC_ERR BIT(7)
+#define MTK_PHY_LED1_RX_IDLE_ERR BIT(8)
+#define MTK_PHY_LED1_FORCE_BLINK BIT(9)
+
+#define MTK_PHY_RG_BG_RASEL 0x115
+#define MTK_PHY_RG_BG_RASEL_MASK GENMASK(2, 0)
+
+/* These macro privides efuse parsing for internal phy. */
+#define EFS_DA_TX_I2MPB_A(x) (((x) >> 0) & GENMASK(5, 0))
+#define EFS_DA_TX_I2MPB_B(x) (((x) >> 6) & GENMASK(5, 0))
+#define EFS_DA_TX_I2MPB_C(x) (((x) >> 12) & GENMASK(5, 0))
+#define EFS_DA_TX_I2MPB_D(x) (((x) >> 18) & GENMASK(5, 0))
+#define EFS_DA_TX_AMP_OFFSET_A(x) (((x) >> 24) & GENMASK(5, 0))
+
+#define EFS_DA_TX_AMP_OFFSET_B(x) (((x) >> 0) & GENMASK(5, 0))
+#define EFS_DA_TX_AMP_OFFSET_C(x) (((x) >> 6) & GENMASK(5, 0))
+#define EFS_DA_TX_AMP_OFFSET_D(x) (((x) >> 12) & GENMASK(5, 0))
+#define EFS_DA_TX_R50_A(x) (((x) >> 18) & GENMASK(5, 0))
+#define EFS_DA_TX_R50_B(x) (((x) >> 24) & GENMASK(5, 0))
+
+#define EFS_DA_TX_R50_C(x) (((x) >> 0) & GENMASK(5, 0))
+#define EFS_DA_TX_R50_D(x) (((x) >> 6) & GENMASK(5, 0))
+
+#define EFS_RG_BG_RASEL(x) (((x) >> 4) & GENMASK(2, 0))
+#define EFS_RG_REXT_TRIM(x) (((x) >> 7) & GENMASK(5, 0))
+
+enum {
+ NO_PAIR,
+ PAIR_A,
+ PAIR_B,
+ PAIR_C,
+ PAIR_D,
+};
+
+enum {
+ GPHY_PORT0,
+ GPHY_PORT1,
+ GPHY_PORT2,
+ GPHY_PORT3,
+};
+
+enum calibration_mode {
+ EFUSE_K,
+ SW_K
+};
+
+enum CAL_ITEM {
+ REXT,
+ TX_OFFSET,
+ TX_AMP,
+ TX_R50,
+ TX_VCM
+};
+
+enum CAL_MODE {
+ EFUSE_M,
+ SW_M
+};
+
+struct mtk_socphy_shared_priv {
+ u32 boottrap;
+};
+
+static int mtk_socphy_read_page(struct phy_device *phydev)
+{
+ return __phy_read(phydev, MTK_EXT_PAGE_ACCESS);
+}
+
+static int mtk_socphy_write_page(struct phy_device *phydev, int page)
+{
+ return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page);
+}
+
+/* One calibration cycle consists of:
+ * 1.Set DA_CALIN_FLAG high to start calibration. Keep it high
+ * until AD_CAL_COMP is ready to output calibration result.
+ * 2.Wait until DA_CAL_CLK is available.
+ * 3.Fetch AD_CAL_COMP_OUT.
+ */
+static int cal_cycle(struct phy_device *phydev, int devad,
+ u32 regnum, u16 mask, u16 cal_val)
+{
+ int reg_val;
+ int ret;
+
+ phy_modify_mmd(phydev, devad, regnum,
+ mask, cal_val);
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN,
+ MTK_PHY_DA_CALIN_FLAG);
+
+ ret = phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_AD_CAL_CLK, reg_val,
+ reg_val & MTK_PHY_DA_CAL_CLK, 500,
+ ANALOG_INTERNAL_OPERATION_MAX_US, false);
+ if (ret) {
+ phydev_err(phydev, "Calibration cycle timeout\n");
+ return ret;
+ }
+
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN,
+ MTK_PHY_DA_CALIN_FLAG);
+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CAL_COMP) >>
+ MTK_PHY_AD_CAL_COMP_OUT_SHIFT;
+ phydev_dbg(phydev, "cal_val: 0x%x, ret: %d\n", cal_val, ret);
+
+ return ret;
+}
+
+static int rext_fill_result(struct phy_device *phydev, u16 *buf)
+{
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG5,
+ MTK_PHY_RG_REXT_TRIM_MASK, buf[0] << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_RG_BG_RASEL,
+ MTK_PHY_RG_BG_RASEL_MASK, buf[1]);
+
+ return 0;
+}
+
+static int rext_cal_efuse(struct phy_device *phydev, u32 *buf)
+{
+ u16 rext_cal_val[2];
+
+ rext_cal_val[0] = EFS_RG_REXT_TRIM(buf[3]);
+ rext_cal_val[1] = EFS_RG_BG_RASEL(buf[3]);
+ rext_fill_result(phydev, rext_cal_val);
+
+ return 0;
+}
+
+static int tx_offset_fill_result(struct phy_device *phydev, u16 *buf)
+{
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B,
+ MTK_PHY_CR_TX_AMP_OFFSET_A_MASK, buf[0] << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B,
+ MTK_PHY_CR_TX_AMP_OFFSET_B_MASK, buf[1]);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D,
+ MTK_PHY_CR_TX_AMP_OFFSET_C_MASK, buf[2] << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D,
+ MTK_PHY_CR_TX_AMP_OFFSET_D_MASK, buf[3]);
+
+ return 0;
+}
+
+static int tx_offset_cal_efuse(struct phy_device *phydev, u32 *buf)
+{
+ u16 tx_offset_cal_val[4];
+
+ tx_offset_cal_val[0] = EFS_DA_TX_AMP_OFFSET_A(buf[0]);
+ tx_offset_cal_val[1] = EFS_DA_TX_AMP_OFFSET_B(buf[1]);
+ tx_offset_cal_val[2] = EFS_DA_TX_AMP_OFFSET_C(buf[1]);
+ tx_offset_cal_val[3] = EFS_DA_TX_AMP_OFFSET_D(buf[1]);
+
+ tx_offset_fill_result(phydev, tx_offset_cal_val);
+
+ return 0;
+}
+
+static int tx_amp_fill_result(struct phy_device *phydev, u16 *buf)
+{
+ int i;
+ int bias[16] = {};
+ const int vals_9461[16] = { 7, 1, 4, 7,
+ 7, 1, 4, 7,
+ 7, 1, 4, 7,
+ 7, 1, 4, 7 };
+ const int vals_9481[16] = { 10, 6, 6, 10,
+ 10, 6, 6, 10,
+ 10, 6, 6, 10,
+ 10, 6, 6, 10 };
+ switch (phydev->drv->phy_id) {
+ case MTK_GPHY_ID_MT7981:
+ /* We add some calibration to efuse values
+ * due to board level influence.
+ * GBE: +7, TBT: +1, HBT: +4, TST: +7
+ */
+ memcpy(bias, (const void *)vals_9461, sizeof(bias));
+ break;
+ case MTK_GPHY_ID_MT7988:
+ memcpy(bias, (const void *)vals_9481, sizeof(bias));
+ break;
+ }
+
+ /* Prevent overflow */
+ for (i = 0; i < 12; i++) {
+ if (buf[i >> 2] + bias[i] > 63) {
+ buf[i >> 2] = 63;
+ bias[i] = 0;
+ }
+ }
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG,
+ MTK_PHY_DA_TX_I2MPB_A_GBE_MASK, (buf[0] + bias[0]) << 10);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG,
+ MTK_PHY_DA_TX_I2MPB_A_TBT_MASK, buf[0] + bias[1]);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2,
+ MTK_PHY_DA_TX_I2MPB_A_HBT_MASK, (buf[0] + bias[2]) << 10);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2,
+ MTK_PHY_DA_TX_I2MPB_A_TST_MASK, buf[0] + bias[3]);
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1,
+ MTK_PHY_DA_TX_I2MPB_B_GBE_MASK, (buf[1] + bias[4]) << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1,
+ MTK_PHY_DA_TX_I2MPB_B_TBT_MASK, buf[1] + bias[5]);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2,
+ MTK_PHY_DA_TX_I2MPB_B_HBT_MASK, (buf[1] + bias[6]) << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2,
+ MTK_PHY_DA_TX_I2MPB_B_TST_MASK, buf[1] + bias[7]);
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1,
+ MTK_PHY_DA_TX_I2MPB_C_GBE_MASK, (buf[2] + bias[8]) << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1,
+ MTK_PHY_DA_TX_I2MPB_C_TBT_MASK, buf[2] + bias[9]);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2,
+ MTK_PHY_DA_TX_I2MPB_C_HBT_MASK, (buf[2] + bias[10]) << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2,
+ MTK_PHY_DA_TX_I2MPB_C_TST_MASK, buf[2] + bias[11]);
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1,
+ MTK_PHY_DA_TX_I2MPB_D_GBE_MASK, (buf[3] + bias[12]) << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1,
+ MTK_PHY_DA_TX_I2MPB_D_TBT_MASK, buf[3] + bias[13]);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2,
+ MTK_PHY_DA_TX_I2MPB_D_HBT_MASK, (buf[3] + bias[14]) << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2,
+ MTK_PHY_DA_TX_I2MPB_D_TST_MASK, buf[3] + bias[15]);
+
+ return 0;
+}
+
+static int tx_amp_cal_efuse(struct phy_device *phydev, u32 *buf)
+{
+ u16 tx_amp_cal_val[4];
+
+ tx_amp_cal_val[0] = EFS_DA_TX_I2MPB_A(buf[0]);
+ tx_amp_cal_val[1] = EFS_DA_TX_I2MPB_B(buf[0]);
+ tx_amp_cal_val[2] = EFS_DA_TX_I2MPB_C(buf[0]);
+ tx_amp_cal_val[3] = EFS_DA_TX_I2MPB_D(buf[0]);
+ tx_amp_fill_result(phydev, tx_amp_cal_val);
+
+ return 0;
+}
+
+static int tx_r50_fill_result(struct phy_device *phydev, u16 tx_r50_cal_val,
+ u8 txg_calen_x)
+{
+ int bias = 0;
+ u16 reg, val;
+
+ if (phydev->drv->phy_id == MTK_GPHY_ID_MT7988)
+ bias = -2;
+
+ val = clamp_val(bias + tx_r50_cal_val, 0, 63);
+
+ switch (txg_calen_x) {
+ case PAIR_A:
+ reg = MTK_PHY_DA_TX_R50_PAIR_A;
+ break;
+ case PAIR_B:
+ reg = MTK_PHY_DA_TX_R50_PAIR_B;
+ break;
+ case PAIR_C:
+ reg = MTK_PHY_DA_TX_R50_PAIR_C;
+ break;
+ case PAIR_D:
+ reg = MTK_PHY_DA_TX_R50_PAIR_D;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, reg, val | val << 8);
+
+ return 0;
+}
+
+static int tx_r50_cal_efuse(struct phy_device *phydev, u32 *buf,
+ u8 txg_calen_x)
+{
+ u16 tx_r50_cal_val;
+
+ switch (txg_calen_x) {
+ case PAIR_A:
+ tx_r50_cal_val = EFS_DA_TX_R50_A(buf[1]);
+ break;
+ case PAIR_B:
+ tx_r50_cal_val = EFS_DA_TX_R50_B(buf[1]);
+ break;
+ case PAIR_C:
+ tx_r50_cal_val = EFS_DA_TX_R50_C(buf[2]);
+ break;
+ case PAIR_D:
+ tx_r50_cal_val = EFS_DA_TX_R50_D(buf[2]);
+ break;
+ default:
+ return -EINVAL;
+ }
+ tx_r50_fill_result(phydev, tx_r50_cal_val, txg_calen_x);
+
+ return 0;
+}
+
+static int tx_vcm_cal_sw(struct phy_device *phydev, u8 rg_txreserve_x)
+{
+ u8 lower_idx, upper_idx, txreserve_val;
+ u8 lower_ret, upper_ret;
+ int ret;
+
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0,
+ MTK_PHY_RG_ANA_CALEN);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0,
+ MTK_PHY_RG_CAL_CKINV);
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1,
+ MTK_PHY_RG_TXVOS_CALEN);
+
+ switch (rg_txreserve_x) {
+ case PAIR_A:
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DASN_DAC_IN0_A,
+ MTK_PHY_DASN_DAC_IN0_A_MASK);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DASN_DAC_IN1_A,
+ MTK_PHY_DASN_DAC_IN1_A_MASK);
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_ANA_CAL_RG0,
+ MTK_PHY_RG_ZCALEN_A);
+ break;
+ case PAIR_B:
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DASN_DAC_IN0_B,
+ MTK_PHY_DASN_DAC_IN0_B_MASK);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DASN_DAC_IN1_B,
+ MTK_PHY_DASN_DAC_IN1_B_MASK);
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_ANA_CAL_RG1,
+ MTK_PHY_RG_ZCALEN_B);
+ break;
+ case PAIR_C:
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DASN_DAC_IN0_C,
+ MTK_PHY_DASN_DAC_IN0_C_MASK);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DASN_DAC_IN1_C,
+ MTK_PHY_DASN_DAC_IN1_C_MASK);
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_ANA_CAL_RG1,
+ MTK_PHY_RG_ZCALEN_C);
+ break;
+ case PAIR_D:
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DASN_DAC_IN0_D,
+ MTK_PHY_DASN_DAC_IN0_D_MASK);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DASN_DAC_IN1_D,
+ MTK_PHY_DASN_DAC_IN1_D_MASK);
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_ANA_CAL_RG1,
+ MTK_PHY_RG_ZCALEN_D);
+ break;
+ default:
+ ret = -EINVAL;
+ goto restore;
+ }
+
+ lower_idx = TXRESERVE_MIN;
+ upper_idx = TXRESERVE_MAX;
+
+ phydev_dbg(phydev, "Start TX-VCM SW cal.\n");
+ while ((upper_idx - lower_idx) > 1) {
+ txreserve_val = DIV_ROUND_CLOSEST(lower_idx + upper_idx, 2);
+ ret = cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9,
+ MTK_PHY_DA_RX_PSBN_TBT_MASK |
+ MTK_PHY_DA_RX_PSBN_HBT_MASK |
+ MTK_PHY_DA_RX_PSBN_GBE_MASK |
+ MTK_PHY_DA_RX_PSBN_LP_MASK,
+ txreserve_val << 12 | txreserve_val << 8 |
+ txreserve_val << 4 | txreserve_val);
+ if (ret == 1) {
+ upper_idx = txreserve_val;
+ upper_ret = ret;
+ } else if (ret == 0) {
+ lower_idx = txreserve_val;
+ lower_ret = ret;
+ } else {
+ goto restore;
+ }
+ }
+
+ if (lower_idx == TXRESERVE_MIN) {
+ lower_ret = cal_cycle(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RXADC_CTRL_RG9,
+ MTK_PHY_DA_RX_PSBN_TBT_MASK |
+ MTK_PHY_DA_RX_PSBN_HBT_MASK |
+ MTK_PHY_DA_RX_PSBN_GBE_MASK |
+ MTK_PHY_DA_RX_PSBN_LP_MASK,
+ lower_idx << 12 | lower_idx << 8 |
+ lower_idx << 4 | lower_idx);
+ ret = lower_ret;
+ } else if (upper_idx == TXRESERVE_MAX) {
+ upper_ret = cal_cycle(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RXADC_CTRL_RG9,
+ MTK_PHY_DA_RX_PSBN_TBT_MASK |
+ MTK_PHY_DA_RX_PSBN_HBT_MASK |
+ MTK_PHY_DA_RX_PSBN_GBE_MASK |
+ MTK_PHY_DA_RX_PSBN_LP_MASK,
+ upper_idx << 12 | upper_idx << 8 |
+ upper_idx << 4 | upper_idx);
+ ret = upper_ret;
+ }
+ if (ret < 0)
+ goto restore;
+
+ /* We calibrate TX-VCM in different logic. Check upper index and then
+ * lower index. If this calibration is valid, apply lower index's result.
+ */
+ ret = upper_ret - lower_ret;
+ if (ret == 1) {
+ ret = 0;
+ /* Make sure we use upper_idx in our calibration system */
+ cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9,
+ MTK_PHY_DA_RX_PSBN_TBT_MASK |
+ MTK_PHY_DA_RX_PSBN_HBT_MASK |
+ MTK_PHY_DA_RX_PSBN_GBE_MASK |
+ MTK_PHY_DA_RX_PSBN_LP_MASK,
+ upper_idx << 12 | upper_idx << 8 |
+ upper_idx << 4 | upper_idx);
+ phydev_dbg(phydev, "TX-VCM SW cal result: 0x%x\n", upper_idx);
+ } else if (lower_idx == TXRESERVE_MIN && upper_ret == 1 &&
+ lower_ret == 1) {
+ ret = 0;
+ cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9,
+ MTK_PHY_DA_RX_PSBN_TBT_MASK |
+ MTK_PHY_DA_RX_PSBN_HBT_MASK |
+ MTK_PHY_DA_RX_PSBN_GBE_MASK |
+ MTK_PHY_DA_RX_PSBN_LP_MASK,
+ lower_idx << 12 | lower_idx << 8 |
+ lower_idx << 4 | lower_idx);
+ phydev_warn(phydev, "TX-VCM SW cal result at low margin 0x%x\n",
+ lower_idx);
+ } else if (upper_idx == TXRESERVE_MAX && upper_ret == 0 &&
+ lower_ret == 0) {
+ ret = 0;
+ phydev_warn(phydev, "TX-VCM SW cal result at high margin 0x%x\n",
+ upper_idx);
+ } else {
+ ret = -EINVAL;
+ }
+
+restore:
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0,
+ MTK_PHY_RG_ANA_CALEN);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1,
+ MTK_PHY_RG_TXVOS_CALEN);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0,
+ MTK_PHY_RG_ZCALEN_A);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1,
+ MTK_PHY_RG_ZCALEN_B | MTK_PHY_RG_ZCALEN_C |
+ MTK_PHY_RG_ZCALEN_D);
+
+ return ret;
+}
+
+static void mt798x_phy_common_finetune(struct phy_device *phydev)
+{
+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5);
+ /* EnabRandUpdTrig = 1 */
+ __phy_write(phydev, 0x11, 0x2f00);
+ __phy_write(phydev, 0x12, 0xe);
+ __phy_write(phydev, 0x10, 0x8fb0);
+
+ /* NormMseLoThresh = 85 */
+ __phy_write(phydev, 0x11, 0x55a0);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x83aa);
+
+ /* TrFreeze = 0 */
+ __phy_write(phydev, 0x11, 0x0);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x9686);
+
+ /* SSTrKp1000Slv = 5 */
+ __phy_write(phydev, 0x11, 0xbaef);
+ __phy_write(phydev, 0x12, 0x2e);
+ __phy_write(phydev, 0x10, 0x968c);
+
+ /* MrvlTrFix100Kp = 3, MrvlTrFix100Kf = 2,
+ * MrvlTrFix1000Kp = 3, MrvlTrFix1000Kf = 2
+ */
+ __phy_write(phydev, 0x11, 0xd10a);
+ __phy_write(phydev, 0x12, 0x34);
+ __phy_write(phydev, 0x10, 0x8f82);
+
+ /* VcoSlicerThreshBitsHigh */
+ __phy_write(phydev, 0x11, 0x5555);
+ __phy_write(phydev, 0x12, 0x55);
+ __phy_write(phydev, 0x10, 0x8ec0);
+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0);
+
+ /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 9*/
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234,
+ MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK,
+ BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0x9));
+
+ /* rg_tr_lpf_cnt_val = 512 */
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LPF_CNT_VAL, 0x200);
+
+ /* IIR2 related */
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K1_L, 0x82);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K1_U, 0x0);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K2_L, 0x103);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K2_U, 0x0);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K3_L, 0x82);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K3_U, 0x0);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K4_L, 0xd177);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K4_U, 0x3);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K5_L, 0x2c82);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K5_U, 0xe);
+
+ /* FFE peaking */
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG27C,
+ MTK_PHY_VGASTATE_FFE_THR_ST1_MASK, 0x1b << 8);
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG27D,
+ MTK_PHY_VGASTATE_FFE_THR_ST2_MASK, 0x1e);
+
+ /* Disable LDO pump */
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_PUMP_EN_PAIRAB, 0x0);
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_PUMP_EN_PAIRCD, 0x0);
+ /* Adjust LDO output voltage */
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_OUTPUT_V, 0x2222);
+}
+
+static void mt7981_phy_finetune(struct phy_device *phydev)
+{
+ u16 val[8] = { 0x01ce, 0x01c1,
+ 0x020f, 0x0202,
+ 0x03d0, 0x03c0,
+ 0x0013, 0x0005 };
+ int i, k;
+
+ /* 100M eye finetune:
+ * Keep middle level of TX MLT3 shapper as default.
+ * Only change TX MLT3 overshoot level here.
+ */
+ for (k = 0, i = 1; i < 12; i++) {
+ if (i % 3 == 0)
+ continue;
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[k++]);
+ }
+
+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5);
+ /* SlvDSPreadyTime = 24, MasDSPreadyTime = 24 */
+ __phy_write(phydev, 0x11, 0xc71);
+ __phy_write(phydev, 0x12, 0xc);
+ __phy_write(phydev, 0x10, 0x8fae);
+
+ /* ResetSyncOffset = 6 */
+ __phy_write(phydev, 0x11, 0x600);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x8fc0);
+
+ /* VgaDecRate = 1 */
+ __phy_write(phydev, 0x11, 0x4c2a);
+ __phy_write(phydev, 0x12, 0x3e);
+ __phy_write(phydev, 0x10, 0x8fa4);
+
+ /* FfeUpdGainForce = 4 */
+ __phy_write(phydev, 0x11, 0x240);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x9680);
+
+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0);
+}
+
+static void mt7988_phy_finetune(struct phy_device *phydev)
+{
+ u16 val[12] = { 0x0187, 0x01cd, 0x01c8, 0x0182,
+ 0x020d, 0x0206, 0x0384, 0x03d0,
+ 0x03c6, 0x030a, 0x0011, 0x0005 };
+ int i;
+
+ /* Set default MLT3 shaper first */
+ for (i = 0; i < 12; i++)
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[i]);
+
+ /* TCT finetune */
+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_TX_FILTER, 0x5);
+
+ /* Disable TX power saving */
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG7,
+ MTK_PHY_DA_AD_BUF_BIAS_LP_MASK, 0x3 << 8);
+
+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5);
+
+ /* SlvDSPreadyTime = 24, MasDSPreadyTime = 12 */
+ __phy_write(phydev, 0x11, 0x671);
+ __phy_write(phydev, 0x12, 0xc);
+ __phy_write(phydev, 0x10, 0x8fae);
+
+ /* ResetSyncOffset = 5 */
+ __phy_write(phydev, 0x11, 0x500);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x8fc0);
+
+ /* VgaDecRate is 1 at default on mt7988 */
+
+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0);
+
+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_2A30);
+ /* TxClkOffset = 2 */
+ __phy_modify(phydev, MTK_PHY_ANARG_RG, MTK_PHY_TCLKOFFSET_MASK,
+ FIELD_PREP(MTK_PHY_TCLKOFFSET_MASK, 0x2));
+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0);
+}
+
+static void mt798x_phy_eee(struct phy_device *phydev)
+{
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG120,
+ MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK |
+ MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK,
+ FIELD_PREP(MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK, 0x0) |
+ FIELD_PREP(MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK, 0x14));
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122,
+ MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK,
+ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK,
+ 0xff));
+
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_TESTMUX_ADC_CTRL,
+ MTK_PHY_RG_TXEN_DIG_MASK);
+
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DEV1E_REG19b, MTK_PHY_BYPASS_DSP_LPI_READY);
+
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_DEV1E_REG234, MTK_PHY_TR_LP_IIR_EEE_EN);
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG238,
+ MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK |
+ MTK_PHY_LPI_SLV_SEND_TX_EN,
+ FIELD_PREP(MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK, 0x120));
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG239,
+ MTK_PHY_LPI_SEND_LOC_TIMER_MASK |
+ MTK_PHY_LPI_TXPCS_LOC_RCV,
+ FIELD_PREP(MTK_PHY_LPI_SEND_LOC_TIMER_MASK, 0x117));
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2C7,
+ MTK_PHY_MAX_GAIN_MASK | MTK_PHY_MIN_GAIN_MASK,
+ FIELD_PREP(MTK_PHY_MAX_GAIN_MASK, 0x8) |
+ FIELD_PREP(MTK_PHY_MIN_GAIN_MASK, 0x13));
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2D1,
+ MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK,
+ FIELD_PREP(MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK,
+ 0x33) |
+ MTK_PHY_LPI_SKIP_SD_SLV_TR | MTK_PHY_LPI_TR_READY |
+ MTK_PHY_LPI_VCO_EEE_STG0_EN);
+
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG323,
+ MTK_PHY_EEE_WAKE_MAS_INT_DC |
+ MTK_PHY_EEE_WAKE_SLV_INT_DC);
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG324,
+ MTK_PHY_SMI_DETCNT_MAX_MASK,
+ FIELD_PREP(MTK_PHY_SMI_DETCNT_MAX_MASK, 0x3f) |
+ MTK_PHY_SMI_DET_MAX_EN);
+
+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG326,
+ MTK_PHY_LPI_MODE_SD_ON | MTK_PHY_RESET_RANDUPD_CNT |
+ MTK_PHY_TREC_UPDATE_ENAB_CLR |
+ MTK_PHY_LPI_QUIT_WAIT_DFE_SIG_DET_OFF |
+ MTK_PHY_TR_READY_SKIP_AFE_WAKEUP);
+
+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5);
+ /* Regsigdet_sel_1000 = 0 */
+ __phy_write(phydev, 0x11, 0xb);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x9690);
+
+ /* REG_EEE_st2TrKf1000 = 3 */
+ __phy_write(phydev, 0x11, 0x114f);
+ __phy_write(phydev, 0x12, 0x2);
+ __phy_write(phydev, 0x10, 0x969a);
+
+ /* RegEEE_slv_wake_tr_timer_tar = 6, RegEEE_slv_remtx_timer_tar = 20 */
+ __phy_write(phydev, 0x11, 0x3028);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x969e);
+
+ /* RegEEE_slv_wake_int_timer_tar = 8 */
+ __phy_write(phydev, 0x11, 0x5010);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x96a0);
+
+ /* RegEEE_trfreeze_timer2 = 586 */
+ __phy_write(phydev, 0x11, 0x24a);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x96a8);
+
+ /* RegEEE100Stg1_tar = 16 */
+ __phy_write(phydev, 0x11, 0x3210);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x96b8);
+
+ /* REGEEE_wake_slv_tr_wait_dfesigdet_en = 1 */
+ __phy_write(phydev, 0x11, 0x1463);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x96ca);
+
+ /* DfeTailEnableVgaThresh1000 = 27 */
+ __phy_write(phydev, 0x11, 0x36);
+ __phy_write(phydev, 0x12, 0x0);
+ __phy_write(phydev, 0x10, 0x8f80);
+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0);
+
+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_3);
+ __phy_modify(phydev, MTK_PHY_LPI_REG_14, MTK_PHY_LPI_WAKE_TIMER_1000_MASK,
+ FIELD_PREP(MTK_PHY_LPI_WAKE_TIMER_1000_MASK, 0x19c));
+
+ __phy_modify(phydev, MTK_PHY_LPI_REG_1c, MTK_PHY_SMI_DET_ON_THRESH_MASK,
+ FIELD_PREP(MTK_PHY_SMI_DET_ON_THRESH_MASK, 0xc));
+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0);
+
+ phy_modify_mmd(phydev, MDIO_MMD_VEND1,
+ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122,
+ MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK,
+ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, 0xff));
+}
+
+static int cal_sw(struct phy_device *phydev, enum CAL_ITEM cal_item,
+ u8 start_pair, u8 end_pair)
+{
+ u8 pair_n;
+ int ret;
+
+ for (pair_n = start_pair; pair_n <= end_pair; pair_n++) {
+ /* TX_OFFSET & TX_AMP have no SW calibration. */
+ switch (cal_item) {
+ case TX_VCM:
+ ret = tx_vcm_cal_sw(phydev, pair_n);
+ break;
+ default:
+ return -EINVAL;
+ }
+ if (ret)
+ return ret;
+ }
+ return 0;
+}
+
+static int cal_efuse(struct phy_device *phydev, enum CAL_ITEM cal_item,
+ u8 start_pair, u8 end_pair, u32 *buf)
+{
+ u8 pair_n;
+ int ret;
+
+ for (pair_n = start_pair; pair_n <= end_pair; pair_n++) {
+ /* TX_VCM has no efuse calibration. */
+ switch (cal_item) {
+ case REXT:
+ ret = rext_cal_efuse(phydev, buf);
+ break;
+ case TX_OFFSET:
+ ret = tx_offset_cal_efuse(phydev, buf);
+ break;
+ case TX_AMP:
+ ret = tx_amp_cal_efuse(phydev, buf);
+ break;
+ case TX_R50:
+ ret = tx_r50_cal_efuse(phydev, buf, pair_n);
+ break;
+ default:
+ return -EINVAL;
+ }
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int start_cal(struct phy_device *phydev, enum CAL_ITEM cal_item,
+ enum CAL_MODE cal_mode, u8 start_pair,
+ u8 end_pair, u32 *buf)
+{
+ int ret;
+
+ switch (cal_mode) {
+ case EFUSE_M:
+ ret = cal_efuse(phydev, cal_item, start_pair,
+ end_pair, buf);
+ break;
+ case SW_M:
+ ret = cal_sw(phydev, cal_item, start_pair, end_pair);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (ret) {
+ phydev_err(phydev, "cal %d failed\n", cal_item);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int mt798x_phy_calibration(struct phy_device *phydev)
+{
+ int ret = 0;
+ u32 *buf;
+ size_t len;
+ struct nvmem_cell *cell;
+
+ cell = nvmem_cell_get(&phydev->mdio.dev, "phy-cal-data");
+ if (IS_ERR(cell)) {
+ if (PTR_ERR(cell) == -EPROBE_DEFER)
+ return PTR_ERR(cell);
+ return 0;
+ }
+
+ buf = (u32 *)nvmem_cell_read(cell, &len);
+ if (IS_ERR(buf))
+ return PTR_ERR(buf);
+ nvmem_cell_put(cell);
+
+ if (!buf[0] || !buf[1] || !buf[2] || !buf[3] || len < 4 * sizeof(u32)) {
+ phydev_err(phydev, "invalid efuse data\n");
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ret = start_cal(phydev, REXT, EFUSE_M, NO_PAIR, NO_PAIR, buf);
+ if (ret)
+ goto out;
+ ret = start_cal(phydev, TX_OFFSET, EFUSE_M, NO_PAIR, NO_PAIR, buf);
+ if (ret)
+ goto out;
+ ret = start_cal(phydev, TX_AMP, EFUSE_M, NO_PAIR, NO_PAIR, buf);
+ if (ret)
+ goto out;
+ ret = start_cal(phydev, TX_R50, EFUSE_M, PAIR_A, PAIR_D, buf);
+ if (ret)
+ goto out;
+ ret = start_cal(phydev, TX_VCM, SW_M, PAIR_A, PAIR_A, buf);
+ if (ret)
+ goto out;
+
+out:
+ kfree(buf);
+ return ret;
+}
+
+static int mt798x_phy_config_init(struct phy_device *phydev)
+{
+ switch (phydev->drv->phy_id) {
+ case MTK_GPHY_ID_MT7981:
+ mt7981_phy_finetune(phydev);
+ break;
+ case MTK_GPHY_ID_MT7988:
+ mt7988_phy_finetune(phydev);
+ break;
+ }
+
+ mt798x_phy_common_finetune(phydev);
+ mt798x_phy_eee(phydev);
+
+ return mt798x_phy_calibration(phydev);
+}
+
+static int mt7988_phy_setup_led(struct phy_device *phydev)
+{
+ struct mtk_socphy_shared_priv *priv = phydev->shared->priv;
+ int port = phydev->mdio.addr;
+ u32 reg = priv->boottrap;
+ struct pinctrl *pinctrl;
+
+ phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL,
+ MTK_PHY_LED0_ENABLE | MTK_PHY_LED0_POLARITY |
+ MTK_PHY_LED0_ON_LINK10 |
+ MTK_PHY_LED0_ON_LINK100 |
+ MTK_PHY_LED0_ON_LINK1000);
+ phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_ON_CTRL,
+ MTK_PHY_LED1_ENABLE | MTK_PHY_LED1_POLARITY |
+ MTK_PHY_LED1_ON_LINK10 |
+ MTK_PHY_LED1_ON_LINK100 |
+ MTK_PHY_LED1_ON_LINK1000);
+
+ if ((port == GPHY_PORT0 && reg & BIT(8)) ||
+ (port == GPHY_PORT1 && reg & BIT(9)) ||
+ (port == GPHY_PORT2 && reg & BIT(10)) ||
+ (port == GPHY_PORT3 && reg & BIT(11))) {
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL,
+ MTK_PHY_LED0_POLARITY);
+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_ON_CTRL,
+ MTK_PHY_LED1_POLARITY);
+ }
+
+ phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_BLINK_CTRL,
+ MTK_PHY_LED0_1000TX | MTK_PHY_LED0_1000RX |
+ MTK_PHY_LED0_100TX | MTK_PHY_LED0_100RX |
+ MTK_PHY_LED0_10TX | MTK_PHY_LED0_10RX);
+ phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_BLINK_CTRL,
+ MTK_PHY_LED1_1000TX | MTK_PHY_LED1_1000RX |
+ MTK_PHY_LED1_100TX | MTK_PHY_LED1_100RX |
+ MTK_PHY_LED1_10TX | MTK_PHY_LED1_10RX);
+
+ pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "gbe-led");
+ if (IS_ERR(pinctrl)) {
+ dev_err(&phydev->mdio.bus->dev, "Failed to setup LED pins\n");
+ return PTR_ERR(pinctrl);
+ }
+
+ return 0;
+}
+
+static int mt7988_phy_probe_shared(struct phy_device *phydev)
+{
+ struct mtk_socphy_shared_priv *priv = phydev->shared->priv;
+ void __iomem *boottrap;
+ struct device_node *np;
+ u32 reg;
+
+ np = of_find_compatible_node(NULL, NULL, "mediatek,boottrap");
+ if (!np)
+ return -ENOENT;
+
+ boottrap = of_iomap(np, 0);
+ if (!boottrap)
+ return -ENOMEM;
+
+ reg = readl(boottrap);
+ iounmap(boottrap);
+
+ priv->boottrap = reg;
+
+ return 0;
+}
+
+static int mt7981_phy_probe(struct phy_device *phydev)
+{
+ return mt798x_phy_calibration(phydev);
+}
+
+static int mt7988_phy_probe(struct phy_device *phydev)
+{
+ int err;
+
+ err = devm_phy_package_join(&phydev->mdio.dev, phydev, 0,
+ sizeof(struct mtk_socphy_shared_priv));
+ if (err)
+ return err;
+
+ if (phy_package_probe_once(phydev)) {
+ err = mt7988_phy_probe_shared(phydev);
+ if (err)
+ return err;
+ }
+
+ mt7988_phy_setup_led(phydev);
+
+ return mt798x_phy_calibration(phydev);
+}
+
+static struct phy_driver mtk_socphy_driver[] = {
+ {
+ PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981),
+ .name = "MediaTek MT7981 PHY",
+ .config_init = mt798x_phy_config_init,
+ .config_intr = genphy_no_config_intr,
+ .handle_interrupt = genphy_handle_interrupt_no_ack,
+ .probe = mt7981_phy_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .read_page = mtk_socphy_read_page,
+ .write_page = mtk_socphy_write_page,
+ },
+ {
+ PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988),
+ .name = "MediaTek MT7988 PHY",
+ .config_init = mt798x_phy_config_init,
+ .config_intr = genphy_no_config_intr,
+ .handle_interrupt = genphy_handle_interrupt_no_ack,
+ .probe = mt7988_phy_probe,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .read_page = mtk_socphy_read_page,
+ .write_page = mtk_socphy_write_page,
+ },
+};
+
+module_phy_driver(mtk_socphy_driver);
+
+static struct mdio_device_id __maybe_unused mtk_socphy_tbl[] = {
+ { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981) },
+ { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988) },
+ { }
+};
+
+MODULE_DESCRIPTION("MediaTek SoC Gigabit Ethernet PHY driver");
+MODULE_AUTHOR("Daniel Golle <[email protected]>");
+MODULE_AUTHOR("SkyLake Huang <[email protected]>");
+MODULE_LICENSE("GPL");
+
+MODULE_DEVICE_TABLE(mdio, mtk_socphy_tbl);
diff --git a/drivers/net/phy/mediatek-ge.c b/drivers/net/phy/mediatek-ge.c
index 68ee434f9dea3..a493ae01b267a 100644
--- a/drivers/net/phy/mediatek-ge.c
+++ b/drivers/net/phy/mediatek-ge.c
@@ -102,7 +102,8 @@ static struct phy_driver mtk_gephy_driver[] = {
module_phy_driver(mtk_gephy_driver);
static struct mdio_device_id __maybe_unused mtk_gephy_tbl[] = {
- { PHY_ID_MATCH_VENDOR(0x03a29400) },
+ { PHY_ID_MATCH_EXACT(0x03a29441) },
+ { PHY_ID_MATCH_EXACT(0x03a29412) },
{ }
};
--
2.40.0
On Sat, 22 Apr 2023 13:36:58 +0100 Daniel Golle wrote:
> Some of MediaTek's Filogic SoCs come with built-in gigabit Ethernet
> PHYs which require calibration data from the SoC's efuse.
> Despite the similar design the driver doesn't share any code with the
> existing mediatek-ge.c, so add support for these PHYs by introducing a
> new driver for only MediaTek's ARM64 SoCs.
Andrew, Heiner, how do you feel about this driver?
Daniel, is it high prio for you to get it into 6.4 or 6.5 is okay?
I'm trying to get a read on whether we should merge it because it's
kind of on the goal line for this merge window.
If nobody feels strongly we can do this the traditional way - I'll
just complain about RCT, hence kicking it back out into the field :)
On Mon, Apr 24, 2023 at 06:37:55PM -0700, Jakub Kicinski wrote:
> On Sat, 22 Apr 2023 13:36:58 +0100 Daniel Golle wrote:
> > Some of MediaTek's Filogic SoCs come with built-in gigabit Ethernet
> > PHYs which require calibration data from the SoC's efuse.
> > Despite the similar design the driver doesn't share any code with the
> > existing mediatek-ge.c, so add support for these PHYs by introducing a
> > new driver for only MediaTek's ARM64 SoCs.
>
> Andrew, Heiner, how do you feel about this driver?
It is 95% magic values in magic registers which nobody is every going
to understand without the datasheet. Assuming any of it is actually in
the data sheet. I really think the firmware in this PHY needs a
re-write to avoid exposing all this to the OS. But i don't know if we
have that level of NACK. Having said that, there is a nice quote in
LWN from Thomas Gleixer about this:
https://lwn.net/Articles/928946/
This does seem like a case of 'throw hardware/firmware over the fence
and let software folks deal with it.' There is no other PHY like it in
Linux. So i would like to reject it, but i then suspect we are
punishing the wrong people, Daniel not MediaTek.
I would also drop the LED configuration parts. Leave it at reset
defaults for the moment. It seems like the generic support for
controlling PHY LEDs is making progress and will be merged next cycle.
Andrew
On Mon, Apr 24, 2023 at 06:37:55PM -0700, Jakub Kicinski wrote:
> On Sat, 22 Apr 2023 13:36:58 +0100 Daniel Golle wrote:
> > Some of MediaTek's Filogic SoCs come with built-in gigabit Ethernet
> > PHYs which require calibration data from the SoC's efuse.
> > Despite the similar design the driver doesn't share any code with the
> > existing mediatek-ge.c, so add support for these PHYs by introducing a
> > new driver for only MediaTek's ARM64 SoCs.
>
> Andrew, Heiner, how do you feel about this driver?
>
> Daniel, is it high prio for you to get it into 6.4 or 6.5 is okay?
No rush, as this is mostly relevant for OpenWrt the thing which matters
most to me is having it in the next LTS kernel, so 6.5 should still be
fine I suppose.
>
> I'm trying to get a read on whether we should merge it because it's
> kind of on the goal line for this merge window.
>
> If nobody feels strongly we can do this the traditional way - I'll
> just complain about RCT, hence kicking it back out into the field :)
I understand Andrew's concerns and will resubmit for the next merge
window in 2 weeks, and without the LED part for now until PHY LED
infrastructure is more ready (ie. able to offload 'netdev' trigger
to hardware)
On Tue, 25 Apr 2023 09:27:56 +0100 Daniel Golle wrote:
> > Daniel, is it high prio for you to get it into 6.4 or 6.5 is okay?
>
> No rush, as this is mostly relevant for OpenWrt the thing which matters
> most to me is having it in the next LTS kernel, so 6.5 should still be
> fine I suppose.
>
> >
> > I'm trying to get a read on whether we should merge it because it's
> > kind of on the goal line for this merge window.
> >
> > If nobody feels strongly we can do this the traditional way - I'll
> > just complain about RCT, hence kicking it back out into the field :)
>
> I understand Andrew's concerns and will resubmit for the next merge
> window in 2 weeks, and without the LED part for now until PHY LED
> infrastructure is more ready (ie. able to offload 'netdev' trigger
> to hardware)
Perfect, thanks!