In continuation of patch series posted by Nishanth
for sync of uboot device tree with kernel device tree for AM64 SOC.
https://lore.kernel.org/linux-arm-kernel/[email protected]/
This series extend device tree sync/clean up for J7200 SOC.
This patch series build on top of
https://lore.kernel.org/all/[email protected]
Changes since v1:
https://lore.kernel.org/all/[email protected]/
* Add general purpose timers:
Addded CLKSEL_VD clock for odd numbered timers
Marked MCU_Timer as reserved, fixed clock index for main_timer13
*Configure pinctrl for timer IO pads
Marked mcu_timerio_input as reserved
*main_pmx0 clean up
Splitted into two patches, One for UART and second for
i2c duplication removal
*Add uart pin mux in wkup_pmx0
No change
*Add bootph-pre-ram for u-boot
patch dropped, later will add bootph-pre-ram property
later for all nodes.
Udit Kumar (5):
arm64: dts: ti: k3-j7200: Add general purpose timers
arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
arm64: dts: ti: k3-j7200-common-proc-board: main_pmx0 clean up
arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0
pin mux
arm64: dts: ti: k3-j7200-common-proc-board: Add uart pin mux in
wkup_pmx0
.../dts/ti/k3-j7200-common-proc-board.dts | 32 ++-
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 258 ++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 150 ++++++++++
3 files changed, 436 insertions(+), 4 deletions(-)
--
2.34.1
Add main_uart0 pin mux in board common file
Signed-off-by: Udit Kumar <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 0cc0e1dc40c5..02d2e4b36b18 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -113,6 +113,15 @@ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>;
};
+ main_uart0_pins_default: main_uart0_pins_default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
+ J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
+ J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
+ J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -162,6 +171,8 @@ &main_uart0 {
status = "okay";
/* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart0_pins_default>;
};
&main_uart1 {
--
2.34.1
main_i2c0 pin mux was duplicated in som and common file.
So removing duplicated node from common file
Signed-off-by: Udit Kumar <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 7 -------
1 file changed, 7 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 02d2e4b36b18..e12d93f56c51 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -106,13 +106,6 @@ J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
};
&main_pmx0 {
- main_i2c0_pins_default: main-i2c0-pins-default {
- pinctrl-single,pins = <
- J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
- J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
- >;
- };
-
main_uart0_pins_default: main_uart0_pins_default {
pinctrl-single,pins = <
J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
--
2.34.1
There are 20 general purpose timers on j721e that can be used for
things like PWM using pwm-omap-dmtimer driver. There are also
additional ten timers in the MCU domain which are meant for MCU
firmware usage and hence marked reserved by default.
The odd numbered timers have the option of being cascaded to even
timers to create a 64 bit non-atomic counter which is racy in simple
usage, hence the clock muxes are explicitly setup to individual 32 bit
counters driven off system crystal (HFOSC) as default.
Signed-off-by: Udit Kumar <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 240 ++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 130 ++++++++++
2 files changed, 370 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index ef352e32f19d..c6b15aceea82 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -971,6 +971,246 @@ watchdog1: watchdog@2210000 {
assigned-clock-parents = <&k3_clks 253 5>;
};
+ main_timer0: timer@2400000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2400000 0x00 0x400>;
+ interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 49 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 49 1>;
+ assigned-clock-parents = <&k3_clks 49 2>;
+ power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer1: timer@2410000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2410000 0x00 0x400>;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 50 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 50 1>, <&k3_clks 313 0>;
+ assigned-clock-parents = <&k3_clks 50 2>, <&k3_clks 313 1>;
+ power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer2: timer@2420000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2420000 0x00 0x400>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 51 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 51 1>;
+ assigned-clock-parents = <&k3_clks 51 2>;
+ power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer3: timer@2430000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2430000 0x00 0x400>;
+ interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 52 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 52 1>, <&k3_clks 314 0>;
+ assigned-clock-parents = <&k3_clks 52 2>, <&k3_clks 314 1>;
+ power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer4: timer@2440000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2440000 0x00 0x400>;
+ interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 53 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 53 1>;
+ assigned-clock-parents = <&k3_clks 53 2>;
+ power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer5: timer@2450000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2450000 0x00 0x400>;
+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 54 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 54 1>, <&k3_clks 315 0>;
+ assigned-clock-parents = <&k3_clks 54 2>, <&k3_clks 315 1>;
+ power-domains = <&k3_pds 54 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer6: timer@2460000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2460000 0x00 0x400>;
+ interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 55 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 55 1>;
+ assigned-clock-parents = <&k3_clks 55 2>;
+ power-domains = <&k3_pds 55 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer7: timer@2470000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2470000 0x00 0x400>;
+ interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 57 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 57 1>, <&k3_clks 316 0>;
+ assigned-clock-parents = <&k3_clks 57 2>, <&k3_clks 316 1>;
+ power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer8: timer@2480000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2480000 0x00 0x400>;
+ interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 58 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 58 1>;
+ assigned-clock-parents = <&k3_clks 58 2>;
+ power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer9: timer@2490000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2490000 0x00 0x400>;
+ interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 59 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 59 1>, <&k3_clks 317 0>;
+ assigned-clock-parents = <&k3_clks 59 2>, <&k3_clks 317 1>;
+ power-domains = <&k3_pds 59 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer10: timer@24a0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24a0000 0x00 0x400>;
+ interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 60 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 60 1>;
+ assigned-clock-parents = <&k3_clks 60 2>;
+ power-domains = <&k3_pds 60 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer11: timer@24b0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24b0000 0x00 0x400>;
+ interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 62 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 62 1>, <&k3_clks 318 0>;
+ assigned-clock-parents = <&k3_clks 62 2>, <&k3_clks 318 1>;
+ power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer12: timer@24c0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24c0000 0x00 0x400>;
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 63 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 63 1>;
+ assigned-clock-parents = <&k3_clks 63 2>;
+ power-domains = <&k3_pds 63 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer13: timer@24d0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24d0000 0x00 0x400>;
+ interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 64 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 64 1>, <&k3_clks 319 0>;
+ assigned-clock-parents = <&k3_clks 64 2>, <&k3_clks 319 1>;
+ power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer14: timer@24e0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24e0000 0x00 0x400>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 65 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 65 1>;
+ assigned-clock-parents = <&k3_clks 65 2>;
+ power-domains = <&k3_pds 65 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer15: timer@24f0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24f0000 0x00 0x400>;
+ interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 66 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 66 1>, <&k3_clks 320 0>;
+ assigned-clock-parents = <&k3_clks 66 2>, <&k3_clks 320 1>;
+ power-domains = <&k3_pds 66 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer16: timer@2500000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2500000 0x00 0x400>;
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 67 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 67 1>;
+ assigned-clock-parents = <&k3_clks 67 2>;
+ power-domains = <&k3_pds 67 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer17: timer@2510000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2510000 0x00 0x400>;
+ interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 68 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 68 1>, <&k3_clks 321 0>;
+ assigned-clock-parents = <&k3_clks 68 2>, <&k3_clks 321 1>;
+ power-domains = <&k3_pds 68 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer18: timer@2520000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2520000 0x00 0x400>;
+ interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 69 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 69 1>;
+ assigned-clock-parents = <&k3_clks 69 2>;
+ power-domains = <&k3_pds 69 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer19: timer@2530000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2530000 0x00 0x400>;
+ interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 70 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 70 1>, <&k3_clks 322 0>;
+ assigned-clock-parents = <&k3_clks 70 2>, <&k3_clks 322 1>;
+ power-domains = <&k3_pds 70 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
main_r5fss0: r5fss@5c00000 {
compatible = "ti,j7200-r5fss";
ti,cluster-mode = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 674e695ef844..dcb6696cff17 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -34,6 +34,136 @@ k3_reset: reset-controller {
};
};
+ mcu_timer0: timer@40400000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40400000 0x00 0x400>;
+ interrupts = <GIC_SPI 816 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 35 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 35 1>;
+ assigned-clock-parents = <&k3_clks 35 2>;
+ power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer1: timer@40410000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40410000 0x00 0x400>;
+ interrupts = <GIC_SPI 817 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 71 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 71 1>, <&k3_clks 308 0>;
+ assigned-clock-parents = <&k3_clks 71 2>, <&k3_clks 308 1>;
+ power-domains = <&k3_pds 71 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer2: timer@40420000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40420000 0x00 0x400>;
+ interrupts = <GIC_SPI 818 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 72 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 72 1>;
+ assigned-clock-parents = <&k3_clks 72 2>;
+ power-domains = <&k3_pds 72 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer3: timer@40430000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40430000 0x00 0x400>;
+ interrupts = <GIC_SPI 819 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 73 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 73 1>, <&k3_clks 309 0>;
+ assigned-clock-parents = <&k3_clks 73 2>, <&k3_clks 309 1>;
+ power-domains = <&k3_pds 73 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer4: timer@40440000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40440000 0x00 0x400>;
+ interrupts = <GIC_SPI 820 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 74 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 74 1>;
+ assigned-clock-parents = <&k3_clks 74 2>;
+ power-domains = <&k3_pds 74 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer5: timer@40450000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40450000 0x00 0x400>;
+ interrupts = <GIC_SPI 821 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 75 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 75 1>, <&k3_clks 310 0>;
+ assigned-clock-parents = <&k3_clks 75 2>, <&k3_clks 310 1>;
+ power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer6: timer@40460000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40460000 0x00 0x400>;
+ interrupts = <GIC_SPI 822 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 76 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 76 1>;
+ assigned-clock-parents = <&k3_clks 76 2>;
+ power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer7: timer@40470000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40470000 0x00 0x400>;
+ interrupts = <GIC_SPI 823 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 77 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 77 1>, <&k3_clks 311 0>;
+ assigned-clock-parents = <&k3_clks 77 2>, <&k3_clks 311 1>;
+ power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer8: timer@40480000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40480000 0x00 0x400>;
+ interrupts = <GIC_SPI 824 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 78 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 78 1>;
+ assigned-clock-parents = <&k3_clks 78 2>;
+ power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer9: timer@40490000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40490000 0x00 0x400>;
+ interrupts = <GIC_SPI 825 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 79 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 79 1>, <&k3_clks 312 0>;
+ assigned-clock-parents = <&k3_clks 79 2>, <&k3_clks 312 1>;
+ power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
mcu_conf: syscon@40f00000 {
compatible = "syscon", "simple-mfd";
reg = <0x00 0x40f00000 0x00 0x20000>;
--
2.34.1
Add uart pin mux of wkup domain into common board file.
Signed-off-by: Udit Kumar <[email protected]>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 22 ++++++++++++++++++-
1 file changed, 21 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index e12d93f56c51..809d1c910015 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -79,6 +79,24 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
};
};
+&wkup_pmx0 {
+ mcu_uart0_pins_default: mcu_uart0_pins_default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xf4, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */
+ J721E_WKUP_IOPAD(0xf0, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */
+ J721E_WKUP_IOPAD(0xf8, PIN_INPUT, 0) /* (E20) MCU_UART0_CTSn */
+ J721E_WKUP_IOPAD(0xfc, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */
+ >;
+ };
+
+ wkup_uart0_pins_default: wkup_uart0_pins_default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */
+ J721E_WKUP_IOPAD(0xb4, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */
+ >;
+ };
+};
+
&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
@@ -157,7 +175,9 @@ &wkup_uart0 {
&mcu_uart0 {
status = "okay";
- /* Default pinmux */
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_uart0_pins_default>;
+ clock-frequency = <96000000>;
};
&main_uart0 {
--
2.34.1
There are timer IO pads in the MCU domain, and in the MAIN domain. These
pads can be muxed for the related timers.
There are timer IO control registers for input and output. The registers
for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control
the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and
CTRLMMR_MCU_TIMERIO*_CTRL the output.
The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control
Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the
CASCADE_EN bit is documented in TRM "12.6.3.1 Timers Overview".
For chaining timers, the timer IO control registers also have a CASCADE_EN
input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit
muxes the previous timer output, or possibly and external TIMER_IO pad
source, to the input clock of the selected timer instance for odd numered
timers. For the even numbered timers, the CASCADE_EN bit does not do
anything. The timer cascade input routing options are shown in TRM
"Figure 12-3224. Timers Overview". For handling beyond multiplexing, the
driver support for timer cascading should be likely be handled via the
clock framework.
The MCU timer controls are also marked as reserved for
usage by the MCU firmware.
Cc: Nishanth Menon <[email protected]>
Cc: Vignesh Raghavendra <[email protected]>
Cc: Tony Lindgren <[email protected]>
Signed-off-by: Udit Kumar <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 18 +++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 20 +++++++++++++++++++
2 files changed, 38 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index c6b15aceea82..a9b3bf8a5c6a 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -392,6 +392,24 @@ cpts@3d000 {
};
};
+ /* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */
+ main_timerio_input: pinctrl@104200 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0x104200 0x0 0x50>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x000001ff>;
+ };
+
+ /* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */
+ main_timerio_output: pinctrl@104280 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0x104280 0x0 0x20>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x0000001f>;
+ };
+
main_pmx0: pinctrl@11c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index dcb6696cff17..b518ec9eea32 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -183,6 +183,26 @@ chipid@43000014 {
reg = <0x00 0x43000014 0x00 0x4>;
};
+ /* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */
+ mcu_timerio_input: pinctrl@40f04200 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0x40f04200 0x0 0x28>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x0000000F>;
+ status = "reserved";
+ };
+
+ /* MCU_TIMERIO pad output CTRLMMR_MCU_TIMERIO*_CTRL registers */
+ mcu_timerio_output: pinctrl@40f04280 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0x40f04280 0x0 0x28>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x0000000F>;
+ status = "reserved";
+ };
+
wkup_pmx0: pinctrl@4301c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
--
2.34.1
On 15:07-20230601, Udit Kumar wrote:
> Add main_uart0 pin mux in board common file
$subject is a bit misleading.. I think the intent is to mux the console
explicitly rather than a pinmux cleanup itself.
>
> Signed-off-by: Udit Kumar <[email protected]>
> ---
> arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 0cc0e1dc40c5..02d2e4b36b18 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -113,6 +113,15 @@ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
> >;
> };
>
> + main_uart0_pins_default: main_uart0_pins_default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
> + J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
> + J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
> + J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
> + >;
> + };
> +
> main_i2c1_pins_default: main-i2c1-pins-default {
> pinctrl-single,pins = <
> J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
> @@ -162,6 +171,8 @@ &main_uart0 {
> status = "okay";
> /* Shared with ATF on this platform */
> power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_uart0_pins_default>;
> };
>
> &main_uart1 {
> --
> 2.34.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
* Udit Kumar <[email protected]> [230601 09:38]:
> There are timer IO pads in the MCU domain, and in the MAIN domain. These
> pads can be muxed for the related timers.
>
> There are timer IO control registers for input and output. The registers
> for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control
> the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and
> CTRLMMR_MCU_TIMERIO*_CTRL the output.
>
> The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control
> Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the
> CASCADE_EN bit is documented in TRM "12.6.3.1 Timers Overview".
>
> For chaining timers, the timer IO control registers also have a CASCADE_EN
> input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit
> muxes the previous timer output, or possibly and external TIMER_IO pad
> source, to the input clock of the selected timer instance for odd numered
> timers. For the even numbered timers, the CASCADE_EN bit does not do
> anything. The timer cascade input routing options are shown in TRM
> "Figure 12-3224. Timers Overview". For handling beyond multiplexing, the
> driver support for timer cascading should be likely be handled via the
> clock framework.
>
> The MCU timer controls are also marked as reserved for
> usage by the MCU firmware.
Reviewed-by: Tony Lindgren <[email protected]>
Thanks
On 6/1/2023 4:15 PM, Nishanth Menon wrote:
> On 15:07-20230601, Udit Kumar wrote:
>> Add main_uart0 pin mux in board common file
> $subject is a bit misleading.. I think the intent is to mux the console
> explicitly rather than a pinmux cleanup itself.
oops, missed to changed subject of this patch after split.
Will address in v3.
>> Signed-off-by: Udit Kumar<[email protected]>
>> ---
>> arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 11 +++++++++++
>> 1 file changed, 11 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> index 0cc0e1dc40c5..02d2e4b36b18 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> @@ -113,6 +113,15 @@ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>> >;
>> };
>>
>> + main_uart0_pins_default: main_uart0_pins_default {
>> + pinctrl-single,pins = <
>> + J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
>> + J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
>> + J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
>> + J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
>> + >;
>> + };
>> +
>> main_i2c1_pins_default: main-i2c1-pins-default {
>> pinctrl-single,pins = <
>> J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
>> @@ -162,6 +171,8 @@ &main_uart0 {
>> status = "okay";
>> /* Shared with ATF on this platform */
>> power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&main_uart0_pins_default>;
>> };
>>
>> &main_uart1 {
>> --
>> 2.34.1
>>