Use node labels instead of nodename@address for BCM28155 AP board
to simplify its DTS file.
Signed-off-by: Stanislav Jakubek <[email protected]>
---
Changes in V2:
- keep &pmu (bcm59056) related stuff last in the file
- drop already applied patches
- drop cover letter (since this is now a single patch)
V1 - https://lore.kernel.org/lkml/[email protected]/
arch/arm/boot/dts/broadcom/bcm28155-ap.dts | 94 +++++++++++-----------
1 file changed, 47 insertions(+), 47 deletions(-)
diff --git a/arch/arm/boot/dts/broadcom/bcm28155-ap.dts b/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
index 0a8ad1d673d8..2f3634545e64 100644
--- a/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
+++ b/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
@@ -15,64 +15,64 @@ memory@80000000 {
device_type = "memory";
reg = <0x80000000 0x40000000>; /* 1 GB */
};
+};
- serial@3e000000 {
- status = "okay";
- };
-
- i2c@3e016000 {
- clock-frequency = <400000>;
- status = "okay";
- };
+&bsc1 {
+ clock-frequency = <400000>;
+ status = "okay";
+};
- i2c@3e017000 {
- clock-frequency = <400000>;
- status = "okay";
- };
+&bsc2 {
+ clock-frequency = <400000>;
+ status = "okay";
+};
- i2c@3e018000 {
- clock-frequency = <400000>;
- status = "okay";
- };
+&bsc3 {
+ clock-frequency = <400000>;
+ status = "okay";
+};
- i2c@3500d000 {
- clock-frequency = <100000>;
- status = "okay";
+&pmu_bsc {
+ clock-frequency = <100000>;
+ status = "okay";
- pmu: pmu@8 {
- reg = <0x08>;
- };
+ pmu: pmu@8 {
+ reg = <0x08>;
};
+};
- sdio2: mmc@3f190000 {
- non-removable;
- max-frequency = <48000000>;
- vmmc-supply = <&camldo1_reg>;
- vqmmc-supply = <&iosr1_reg>;
- status = "okay";
- };
+&pwm {
+ status = "okay";
+};
- sdio4: mmc@3f1b0000 {
- max-frequency = <48000000>;
- cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
- vmmc-supply = <&sdldo_reg>;
- vqmmc-supply = <&sdxldo_reg>;
- status = "okay";
- };
+&sdio2 {
+ non-removable;
+ max-frequency = <48000000>;
+ vmmc-supply = <&camldo1_reg>;
+ vqmmc-supply = <&iosr1_reg>;
+ status = "okay";
+};
- pwm: pwm@3e01a000 {
- status = "okay";
- };
+&sdio4 {
+ max-frequency = <48000000>;
+ cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&sdldo_reg>;
+ vqmmc-supply = <&sdxldo_reg>;
+ status = "okay";
+};
- usbotg: usb@3f120000 {
- vusb_d-supply = <&usbldo_reg>;
- vusb_a-supply = <&iosr1_reg>;
- status = "okay";
- };
+&uartb {
+ status = "okay";
+};
- usbphy: usb-phy@3f130000 {
- status = "okay";
- };
+&usbotg {
+ vusb_d-supply = <&usbldo_reg>;
+ vusb_a-supply = <&iosr1_reg>;
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
};
#include "bcm59056.dtsi"
--
2.25.1