2023-09-13 15:19:27

by Romain Perier

[permalink] [raw]
Subject: [PATCH v2 0/3] Add RTC for MStar SSD20xD SoCs

This patches series adds a new driver for the RTC found in the Mstar
SSD202D SoCs. It adds a basic rtc driver, the corresponding devicetree
bindings.

The rtctest (from selftests) has been passed on this driver, with the
following output:

# rtctest
TAP version 13
1..8
# Starting 8 tests from 1 test cases.
# RUN rtc.date_read ...
# rtctest.c:52:date_read:Current RTC date/time is 17/05/2023 15:58:12.
# OK rtc.date_read
ok 1 rtc.date_read
# RUN rtc.date_read_loop ...
# rtctest.c:95:date_read_loop:Continuously reading RTC time for 30s (with 11ms breaks after every read).
# rtctest.c:122:date_read_loop:Performed 888 RTC time reads.
# OK rtc.date_read_loop
ok 2 rtc.date_read_loop
# RUN rtc.uie_read ...
# rtctest.c:137:uie_read:skip update IRQs not supported.
# OK rtc.uie_read
ok 3 rtc.uie_read
# RUN rtc.uie_select ...
# rtctest.c:166:uie_select:skip update IRQs not supported.
# OK rtc.uie_select
ok 4 rtc.uie_select
# RUN rtc.alarm_alm_set ...
# rtctest.c:214:alarm_alm_set:skip alarms are not supported.
# OK rtc.alarm_alm_set
ok 5 rtc.alarm_alm_set
# RUN rtc.alarm_wkalm_set ...
# rtctest.c:274:alarm_wkalm_set:skip alarms are not supported.
# OK rtc.alarm_wkalm_set
ok 6 rtc.alarm_wkalm_set
# RUN rtc.alarm_alm_set_minute ...
# rtctest.c:324:alarm_alm_set_minute:skip alarms are not supported.
# OK rtc.alarm_alm_set_minute
ok 7 rtc.alarm_alm_set_minute
# RUN rtc.alarm_wkalm_set_minute ...
# rtctest.c:384:alarm_wkalm_set_minute:skip alarms are not supported.
# OK rtc.alarm_wkalm_set_minute
ok 8 rtc.alarm_wkalm_set_minute
# PASSED: 8 / 8 tests passed.
# Totals: pass:8 fail:0 xfail:0 xpass:0 skip:0 error:0

Changes since v1:
- Changed the compatible from mstar,ssd20xd-rtc to mstar,ssd20d-rtc.
So the driver, its documentation and the commit messages have been
reworked accordingly.
- Re-worked the dt-binding, I have also simplified the commit message
- Re-worked the commit message for the driver
- Remove redundant logging message for the user in the driver, as
requested by the subsystem maintainer. As these messages are helpful
for debugging purpose, I have switched these to dev_dbg().
- Updated the list of maintainers (sorry for that).

Romain Perier (3):
rtc: Add support for the SSD202D RTC
dt-bindings: rtc: Add Mstar SSD202D RTC
ARM: dts: mstar: Enable rtc for SSD202D

.../bindings/rtc/mstar,ssd202d-rtc.yaml | 35 +++
.../boot/dts/sigmastar/mstar-infinity2m.dtsi | 5 +
drivers/rtc/Kconfig | 11 +
drivers/rtc/Makefile | 1 +
drivers/rtc/rtc-ssd202d.c | 249 ++++++++++++++++++
5 files changed, 301 insertions(+)
create mode 100644 Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml
create mode 100644 drivers/rtc/rtc-ssd202d.c

--
2.39.2


2023-09-13 20:13:51

by Romain Perier

[permalink] [raw]
Subject: [PATCH v2 2/3] dt-bindings: rtc: Add Mstar SSD202D RTC

Add YAML bindings for Mstar SSD202D RTC.

Signed-off-by: Romain Perier <[email protected]>
---
.../bindings/rtc/mstar,ssd202d-rtc.yaml | 35 +++++++++++++++++++
1 file changed, 35 insertions(+)
create mode 100644 Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml

diff --git a/Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml b/Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml
new file mode 100644
index 000000000000..4c1f22ef5a2c
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/mstar,ssd202d-rtc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mstar SSD202D Real Time Clock
+
+maintainers:
+ - Daniel Palmer <[email protected]>
+ - Romain Perier <[email protected]>
+
+allOf:
+ - $ref: rtc.yaml#
+
+properties:
+ compatible:
+ enum:
+ - mstar,ssd202d-rtc
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ rtc@6800 {
+ compatible = "mstar,ssd202d-rtc";
+ reg = <0x6800 0x200>;
+ };
+...
--
2.39.2

2023-09-13 20:17:41

by Romain Perier

[permalink] [raw]
Subject: [PATCH v2 3/3] ARM: dts: mstar: Enable rtc for SSD202D

This adds the definition of the rtc device node. It enables RTC block
for SSD202D SoCs and newer.

Signed-off-by: Romain Perier <[email protected]>
---
arch/arm/boot/dts/sigmastar/mstar-infinity2m.dtsi | 5 +++++
1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/sigmastar/mstar-infinity2m.dtsi b/arch/arm/boot/dts/sigmastar/mstar-infinity2m.dtsi
index 1b485efd7156..b4ac535a73c8 100644
--- a/arch/arm/boot/dts/sigmastar/mstar-infinity2m.dtsi
+++ b/arch/arm/boot/dts/sigmastar/mstar-infinity2m.dtsi
@@ -32,6 +32,11 @@ cpu1: cpu@1 {
};

&riu {
+ rtc@6800 {
+ compatible = "mstar,ssd202d-rtc";
+ reg = <0x6800 0x200>;
+ };
+
smpctrl: smpctrl@204000 {
reg = <0x204000 0x200>;
status = "disabled";
--
2.39.2

2023-09-13 23:30:21

by Romain Perier

[permalink] [raw]
Subject: [PATCH v2 1/3] rtc: Add support for the SSD202D RTC

Newer SigmaStar SSD202D SoCs contain a Real Time Clock, capable of
running while the system is sleeping (battery powered), this is not the
case with the other RTC on older SoCs. This adds basic support for this
RTC block.

Signed-off-by: Romain Perier <[email protected]>
Co-developed-by: Daniel Palmer <[email protected]>
Signed-off-by: Daniel Palmer <[email protected]>
---
drivers/rtc/Kconfig | 11 ++
drivers/rtc/Makefile | 1 +
drivers/rtc/rtc-ssd202d.c | 249 ++++++++++++++++++++++++++++++++++++++
3 files changed, 261 insertions(+)
create mode 100644 drivers/rtc/rtc-ssd202d.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index d7502433c78a..f6c49348d7aa 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1984,4 +1984,15 @@ config RTC_DRV_POLARFIRE_SOC
This driver can also be built as a module, if so, the module
will be called "rtc-mpfs".

+config RTC_DRV_SSD202D
+ tristate "SigmaStar SSD202D RTC"
+ depends on ARCH_MSTARV7 || COMPILE_TEST
+ default ARCH_MSTARV7
+ help
+ If you say yes here you get support for the SigmaStar SSD202D On-Chip
+ Real Time Clock.
+
+ This driver can also be built as a module, if so, the module
+ will be called "rtc-ssd20xd".
+
endif # RTC_CLASS
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index fd209883ee2e..7b03c3abfd78 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -103,6 +103,7 @@ obj-$(CONFIG_RTC_DRV_MESON) += rtc-meson.o
obj-$(CONFIG_RTC_DRV_MOXART) += rtc-moxart.o
obj-$(CONFIG_RTC_DRV_MPC5121) += rtc-mpc5121.o
obj-$(CONFIG_RTC_DRV_MSC313) += rtc-msc313.o
+obj-$(CONFIG_RTC_DRV_SSD202D) += rtc-ssd202d.o
obj-$(CONFIG_RTC_DRV_MSM6242) += rtc-msm6242.o
obj-$(CONFIG_RTC_DRV_MT2712) += rtc-mt2712.o
obj-$(CONFIG_RTC_DRV_MT6397) += rtc-mt6397.o
diff --git a/drivers/rtc/rtc-ssd202d.c b/drivers/rtc/rtc-ssd202d.c
new file mode 100644
index 000000000000..a69e062ad1b4
--- /dev/null
+++ b/drivers/rtc/rtc-ssd202d.c
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Real time clocks driver for MStar/SigmaStar SSD202D SoCs.
+ *
+ * (C) 2021 Daniel Palmer
+ * (C) 2023 Romain Perier
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/rtc.h>
+#include <linux/regmap.h>
+#include <linux/pm.h>
+
+#define REG_CTRL 0x0
+#define REG_CTRL1 0x4
+#define REG_ISO_CTRL 0xc
+#define REG_WRDATA_L 0x10
+#define REG_WRDATA_H 0x14
+#define REG_ISOACK 0x20
+#define REG_RDDATA_L 0x24
+#define REG_RDDATA_H 0x28
+#define REG_RDCNT_L 0x30
+#define REG_RDCNT_H 0x34
+#define REG_CNT_TRIG 0x38
+#define REG_PWRCTRL 0x3c
+#define REG_RTC_TEST 0x54
+
+#define CNT_RD_TRIG_BIT BIT(0)
+#define CNT_RD_BIT BIT(0)
+#define BASE_WR_BIT BIT(1)
+#define BASE_RD_BIT BIT(2)
+#define CNT_RST_BIT BIT(3)
+#define ISO_CTRL_ACK_MASK BIT(3)
+#define ISO_CTRL_ACK_SHIFT 3
+#define SW0_WR_BIT BIT(5)
+#define SW1_WR_BIT BIT(6)
+#define SW0_RD_BIT BIT(7)
+#define SW1_RD_BIT BIT(8)
+
+#define ISO_CTRL_MASK GENMASK(2, 0)
+
+struct ssd202d_rtc {
+ struct rtc_device *rtc_dev;
+ void __iomem *base;
+};
+
+static u8 read_iso_en(void __iomem *base)
+{
+ return readb(base + REG_RTC_TEST) & 0x1;
+}
+
+static u8 read_iso_ctrl_ack(void __iomem *base)
+{
+ return (readb(base + REG_ISOACK) & ISO_CTRL_ACK_MASK) >> ISO_CTRL_ACK_SHIFT;
+}
+
+static int ssd202d_rtc_isoctrl(struct ssd202d_rtc *priv)
+{
+ static const unsigned int sequence[] = { 0x0, 0x1, 0x3, 0x7, 0x5, 0x1, 0x0 };
+ unsigned int val;
+ struct device *dev = &priv->rtc_dev->dev;
+ int i, ret;
+
+ /*
+ * This gates iso_en by writing a special sequence of bytes to iso_ctrl
+ * and ensuring that it has been correctly applied by reading iso_ctrl_ack
+ */
+ for (i = 0; i < ARRAY_SIZE(sequence); i++) {
+ writeb(sequence[i] & ISO_CTRL_MASK, priv->base + REG_ISO_CTRL);
+
+ ret = read_poll_timeout(read_iso_ctrl_ack, val, val == (i % 2), 100,
+ 20 * 100, true, priv->base);
+ if (ret) {
+ dev_dbg(dev, "Timeout waiting for ack byte %i (%x) of sequence\n", i,
+ sequence[i]);
+ return ret;
+ }
+ }
+
+ /*
+ * At this point iso_en should be raised for 1ms
+ */
+ ret = read_poll_timeout(read_iso_en, val, val, 100, 22 * 100, true, priv->base);
+ if (ret)
+ dev_dbg(dev, "Timeout waiting for iso_en\n");
+ mdelay(2);
+ return 0;
+}
+
+static void ssd202d_rtc_read_reg(struct ssd202d_rtc *priv, unsigned int reg,
+ unsigned int field, unsigned int *base)
+{
+ unsigned int l, h;
+ u16 val;
+
+ /* Ask for the content of an RTC value into RDDATA by gating iso_en,
+ * then iso_en is gated and the content of RDDATA can be read
+ */
+ val = readw(priv->base + reg);
+ writew(val | field, priv->base + reg);
+ ssd202d_rtc_isoctrl(priv);
+ writew(val & ~field, priv->base + reg);
+
+ l = readw(priv->base + REG_RDDATA_L);
+ h = readw(priv->base + REG_RDDATA_H);
+
+ *base = (h << 16) | l;
+}
+
+static void ssd202d_rtc_write_reg(struct ssd202d_rtc *priv, unsigned int reg,
+ unsigned int field, u32 base)
+{
+ u16 val;
+
+ /* Set the content of an RTC value from WRDATA by gating iso_en */
+ val = readw(priv->base + reg);
+ writew(val | field, priv->base + reg);
+ writew(base, priv->base + REG_WRDATA_L);
+ writew(base >> 16, priv->base + REG_WRDATA_H);
+ ssd202d_rtc_isoctrl(priv);
+ writew(val & ~field, priv->base + reg);
+}
+
+static int ssd202d_rtc_read_counter(struct ssd202d_rtc *priv, unsigned int *counter)
+{
+ unsigned int l, h;
+ u16 val;
+
+ val = readw(priv->base + REG_CTRL1);
+ writew(val | CNT_RD_BIT, priv->base + REG_CTRL1);
+ ssd202d_rtc_isoctrl(priv);
+ writew(val & ~CNT_RD_BIT, priv->base + REG_CTRL1);
+
+ val = readw(priv->base + REG_CTRL1);
+ writew(val | CNT_RD_TRIG_BIT, priv->base + REG_CNT_TRIG);
+ writew(val & ~CNT_RD_TRIG_BIT, priv->base + REG_CNT_TRIG);
+
+ l = readw(priv->base + REG_RDCNT_L);
+ h = readw(priv->base + REG_RDCNT_H);
+
+ *counter = (h << 16) | l;
+
+ return 0;
+}
+
+static int ssd202d_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+ struct ssd202d_rtc *priv = dev_get_drvdata(dev);
+ unsigned int sw0, base, counter;
+ u32 seconds;
+ int ret;
+
+ /* Check that RTC is enabled by SW */
+ ssd202d_rtc_read_reg(priv, REG_CTRL, SW0_RD_BIT, &sw0);
+ if (sw0 != 1)
+ return -EINVAL;
+
+ /* Get RTC base value from RDDATA */
+ ssd202d_rtc_read_reg(priv, REG_CTRL, BASE_RD_BIT, &base);
+ /* Get RTC counter value from RDDATA */
+ ret = ssd202d_rtc_read_counter(priv, &counter);
+ if (ret)
+ return ret;
+
+ seconds = base + counter;
+
+ rtc_time64_to_tm(seconds, tm);
+
+ return 0;
+}
+
+static int ssd202d_rtc_reset_counter(struct ssd202d_rtc *priv)
+{
+ u16 val;
+
+ val = readw(priv->base + REG_CTRL);
+ writew(val | CNT_RST_BIT, priv->base + REG_CTRL);
+ ssd202d_rtc_isoctrl(priv);
+ writew(val & ~CNT_RST_BIT, priv->base + REG_CTRL);
+ ssd202d_rtc_isoctrl(priv);
+
+ return 0;
+}
+
+static int ssd202d_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+ struct ssd202d_rtc *priv = dev_get_drvdata(dev);
+ unsigned long seconds = rtc_tm_to_time64(tm);
+
+ ssd202d_rtc_write_reg(priv, REG_CTRL, BASE_WR_BIT, seconds);
+ ssd202d_rtc_reset_counter(priv);
+ ssd202d_rtc_write_reg(priv, REG_CTRL, SW0_WR_BIT, 1);
+
+ return 0;
+}
+
+static const struct rtc_class_ops ssd202d_rtc_ops = {
+ .read_time = ssd202d_rtc_read_time,
+ .set_time = ssd202d_rtc_set_time,
+};
+
+static int ssd202d_rtc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ssd202d_rtc *priv;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(struct ssd202d_rtc), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ priv->rtc_dev = devm_rtc_allocate_device(dev);
+ if (IS_ERR(priv->rtc_dev))
+ return PTR_ERR(priv->rtc_dev);
+
+ priv->rtc_dev->ops = &ssd202d_rtc_ops;
+ priv->rtc_dev->range_max = U32_MAX;
+
+ platform_set_drvdata(pdev, priv);
+
+ return devm_rtc_register_device(priv->rtc_dev);
+}
+
+static const struct of_device_id ssd202d_rtc_of_match_table[] = {
+ { .compatible = "mstar,ssd202d-rtc" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ssd202d_rtc_of_match_table);
+
+static struct platform_driver ssd202d_rtc_driver = {
+ .probe = ssd202d_rtc_probe,
+ .driver = {
+ .name = "ssd202d-rtc",
+ .of_match_table = ssd202d_rtc_of_match_table,
+ },
+};
+module_platform_driver(ssd202d_rtc_driver);
+
+MODULE_AUTHOR("Daniel Palmer <[email protected]>");
+MODULE_AUTHOR("Romain Perier <[email protected]>");
+MODULE_DESCRIPTION("MStar SSD202D RTC Driver");
+MODULE_LICENSE("GPL v2");
--
2.39.2

2023-09-14 20:06:25

by Romain Perier

[permalink] [raw]
Subject: Re: [PATCH v2 2/3] dt-bindings: rtc: Add Mstar SSD202D RTC

Le jeu. 14 sept. 2023 à 10:28, Conor Dooley
<[email protected]> a écrit :
>
> On Thu, Sep 14, 2023 at 09:08:52AM +0200, Romain Perier wrote:
> > Le mer. 13 sept. 2023 à 20:30, Conor Dooley <[email protected]> a écrit :
> > >
> > > On Wed, Sep 13, 2023 at 05:16:05PM +0200, Romain Perier wrote:
> > > > Add YAML bindings for Mstar SSD202D RTC.
> > > >
> > > > Signed-off-by: Romain Perier <[email protected]>
> > > > ---
> > > > .../bindings/rtc/mstar,ssd202d-rtc.yaml | 35 +++++++++++++++++++
> > > > 1 file changed, 35 insertions(+)
> > > > create mode 100644 Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml b/Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml
> > > > new file mode 100644
> > > > index 000000000000..4c1f22ef5a2c
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/rtc/mstar,ssd202d-rtc.yaml
> > > > @@ -0,0 +1,35 @@
> > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > > +%YAML 1.2
> > > > +---
> > > > +$id: http://devicetree.org/schemas/rtc/mstar,ssd202d-rtc.yaml#
> > > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > > +
> > > > +title: Mstar SSD202D Real Time Clock
> > > > +
> > > > +maintainers:
> > > > + - Daniel Palmer <[email protected]>
> > > > + - Romain Perier <[email protected]>
> > > > +
> > > > +allOf:
> > > > + - $ref: rtc.yaml#
> > > > +
> > > > +properties:
> > > > + compatible:
> > > > + enum:
> > > > + - mstar,ssd202d-rtc
> > > > + reg:
> > > > + maxItems: 1
> > > > +
> > > > +required:
> > > > + - compatible
> > > > + - reg
> > >
> >
> > Hi,
> >
> > > So, this seems fine to me in isolation, but isn't this now the sort of
> > > thing that can be documented in trivial-rtc.yaml?
> > > Its only got compatible & reg, which seems to fit the bill for that.
> > >
> >
> > With the current state, it might make sense. However, currently, the
> > RTC hw block is mostly
> > reverse-engineered, the driver is not complete yet, things like
> > external irq or wakeup irq might arrive later (once we know how it is
> > wired up and used).
> > So the content of the dt-bindings might change and differ from a
> > simple "compatible & reg" requirement.
>
> It's always possible to move from that to a fully fledged binding at a
> later date. re: interrupts, trivial-rtc permits a single interrupt, so
> it'd still be suitable if the device only has one.

I agree, good point. Yes, we can make the change later, sure. I will
fix it in the next patch series.

Thanks,
Romain

2023-10-15 21:48:26

by Alexandre Belloni

[permalink] [raw]
Subject: Re: [PATCH v2 1/3] rtc: Add support for the SSD202D RTC

Hello Romain,

Sorry for the very long delay,

On 13/09/2023 17:16:04+0200, Romain Perier wrote:
> +MODULE_AUTHOR("Daniel Palmer <[email protected]>");
> +MODULE_AUTHOR("Romain Perier <[email protected]>");
> +MODULE_DESCRIPTION("MStar SSD202D RTC Driver");
> +MODULE_LICENSE("GPL v2");

checkpatch complains rightfully about GPL v2 here. If you agree, I'll
change this to simply GPL.

--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

2023-10-16 14:33:50

by Romain Perier

[permalink] [raw]
Subject: Re: [PATCH v2 1/3] rtc: Add support for the SSD202D RTC

Le dim. 15 oct. 2023 à 23:48, Alexandre Belloni
<[email protected]> a écrit :
>
> Hello Romain,
>
> Sorry for the very long delay,

Hi,

np,

>
> On 13/09/2023 17:16:04+0200, Romain Perier wrote:
> > +MODULE_AUTHOR("Daniel Palmer <[email protected]>");
> > +MODULE_AUTHOR("Romain Perier <[email protected]>");
> > +MODULE_DESCRIPTION("MStar SSD202D RTC Driver");
> > +MODULE_LICENSE("GPL v2");
>
> checkpatch complains rightfully about GPL v2 here. If you agree, I'll
> change this to simply GPL.

Aah, good catch , yes I agree, it will be simpler.

Thanks,
Regards,
Romain

2023-10-16 14:56:13

by Alexandre Belloni

[permalink] [raw]
Subject: Re: [PATCH v2 0/3] Add RTC for MStar SSD20xD SoCs


On Wed, 13 Sep 2023 17:16:03 +0200, Romain Perier wrote:
> This patches series adds a new driver for the RTC found in the Mstar
> SSD202D SoCs. It adds a basic rtc driver, the corresponding devicetree
> bindings.
>
> The rtctest (from selftests) has been passed on this driver, with the
> following output:
>
> [...]

Applied, thanks!

[1/3] rtc: Add support for the SSD202D RTC
commit: ebf6255868e6141c737cacb8d62b0b347f344877
[2/3] dt-bindings: rtc: Add Mstar SSD202D RTC
commit: cfb67623ce281e045ec11e3eddb1b68b879b53a1

Best regards,

--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

2023-10-17 06:09:34

by Romain Perier

[permalink] [raw]
Subject: Re: [PATCH v2 0/3] Add RTC for MStar SSD20xD SoCs

Le lun. 16 oct. 2023 à 16:55, Alexandre Belloni
<[email protected]> a écrit :
>
>
> On Wed, 13 Sep 2023 17:16:03 +0200, Romain Perier wrote:
> > This patches series adds a new driver for the RTC found in the Mstar
> > SSD202D SoCs. It adds a basic rtc driver, the corresponding devicetree
> > bindings.
> >
> > The rtctest (from selftests) has been passed on this driver, with the
> > following output:
> >
> > [...]
>
> Applied, thanks!

Hi,

Thanks!

>
> [1/3] rtc: Add support for the SSD202D RTC
> commit: ebf6255868e6141c737cacb8d62b0b347f344877
> [2/3] dt-bindings: rtc: Add Mstar SSD202D RTC
> commit: cfb67623ce281e045ec11e3eddb1b68b879b53a1
>
> Best regards,

Ah , you also merged dt-bindings, Conor (from dt maintainers) prefers
trivial-rtc.yaml, it makes sense with the current driver.
I planned to make the change for trivial-rtc in v3, so I can adapt the
commit and rename mstar,ssd202d-rtc.yaml to trivial-rtc.yaml, what do
you think ?

Regards,
Romain



>
> --
> Alexandre Belloni, co-owner and COO, Bootlin
> Embedded Linux and Kernel engineering
> https://bootlin.com

2023-10-18 08:27:52

by Alexandre Belloni

[permalink] [raw]
Subject: Re: [PATCH v2 0/3] Add RTC for MStar SSD20xD SoCs

On 17/10/2023 08:09:10+0200, Romain Perier wrote:
> Le lun. 16 oct. 2023 ? 16:55, Alexandre Belloni
> <[email protected]> a ?crit :
> >
> >
> > On Wed, 13 Sep 2023 17:16:03 +0200, Romain Perier wrote:
> > > This patches series adds a new driver for the RTC found in the Mstar
> > > SSD202D SoCs. It adds a basic rtc driver, the corresponding devicetree
> > > bindings.
> > >
> > > The rtctest (from selftests) has been passed on this driver, with the
> > > following output:
> > >
> > > [...]
> >
> > Applied, thanks!
>
> Hi,
>
> Thanks!
>
> >
> > [1/3] rtc: Add support for the SSD202D RTC
> > commit: ebf6255868e6141c737cacb8d62b0b347f344877
> > [2/3] dt-bindings: rtc: Add Mstar SSD202D RTC
> > commit: cfb67623ce281e045ec11e3eddb1b68b879b53a1
> >
> > Best regards,
>
> Ah , you also merged dt-bindings, Conor (from dt maintainers) prefers
> trivial-rtc.yaml, it makes sense with the current driver.
> I planned to make the change for trivial-rtc in v3, so I can adapt the
> commit and rename mstar,ssd202d-rtc.yaml to trivial-rtc.yaml, what do
> you think ?
>

This is fine as-is.

--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com