This serie adds support for the GalaxyCore GC2145 sensor.
Initialization is based on scripts provided by GalaxyCore,
allowing 3 fixed configurations supported for the time being.
Minimum controls have been added in order to allow it to
be successfully used with libcamera and dcmipp driver (under
review) on STM32MP13 platform.
The sensor also supports Bayer formats which will be added
later on.
v5: - serie rebased on top of master branch of tree sailus/media_tree.git
in order to use v4l2_subdev_state_* functions
v4: - bindings: add link-frequencies & correct description
- driver: add link-frequency ctrl and fix pixelrate
and check for link-frequency dt properties
- driver: correct wording / email / add datasheet link
v3: - fix copyright year
- add more gc2145_ func or variable prefixes
- removal of colorspace within struct gc2145_format
- use 1X16 formats since driver is supporting CSI-2 interface only
- use msleep instead of usleep_range
- add pm_runtime_ last_busy & autosuspend handling
- only start streaming AFTER applying ctrls
- correct RGB565 format to generate _LE instead of _BE
- perform pm_runtime configuration prior to v4l2_async_register_subdev_sensor
- remove frame_interval handling and expose HBLANK/VBLANK ctrls
instead
v2: - split vendor-prefixes update into a separate commit
- correction into dt-bindings (description, const i2c address,
lowcase of supplies, node naming
- correct KConfig (avoid VIDEO_V4L2_SUBDEV_API, V4L2_FWNODE and add
V4L2_CCI_I2C)
- usage of v4l2-cci framework for accessing to device registers
- correction in power-on / power-off sequences and update
usleep_range delay
- detail MIPI configuration and stop register access to stop
streaming
- removal of SYSTEM_SLEEP_PM_OPS (and streaming variable)
- various small fixes, typo, oneline functions
- removal of useless HBLANK control considereing that RAW isn't
supported for the time being
- removal of RAW parts
- usage of dev_err_probe
Alain Volmat (3):
dt-bindings: vendor-prefixes: Add prefix for GalaxyCore Inc.
dt-bindings: media: i2c: add galaxycore,gc2145 dt-bindings
media: i2c: gc2145: Galaxy Core GC2145 sensor support
.../bindings/media/i2c/galaxycore,gc2145.yaml | 113 ++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 8 +
drivers/media/i2c/Kconfig | 10 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/gc2145.c | 1446 +++++++++++++++++
6 files changed, 1580 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml
create mode 100644 drivers/media/i2c/gc2145.c
--
2.25.1
Introduction of the Galaxy Core GC2145 XVGA CMOS camera sensor.
Signed-off-by: Alain Volmat <[email protected]>
Reviewed-by: Conor Dooley <[email protected]>
---
.../bindings/media/i2c/galaxycore,gc2145.yaml | 113 ++++++++++++++++++
1 file changed, 113 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml
new file mode 100644
index 000000000000..1726ecca4c77
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml
@@ -0,0 +1,113 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/galaxycore,gc2145.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Galaxy Core 1/5'' UXGA CMOS Image Sensor
+
+maintainers:
+ - Alain Volmat <[email protected]>
+
+description:
+ The Galaxy Core GC2145 is a 2 Megapixel CMOS image sensor, for mobile
+ phone camera applications and digital camera products. GC2145 incorporates a
+ 1616V x 1232H active pixel array, on-chip 10-bit ADC, and image signal
+ processor allowing AE/AWB/interpolation/de-noise/color-conversion and
+ gamma correction. Bayer RGB, RGB565 and YCbCr 4:2:2 can be provided by the
+ sensor. It is programmable through an I2C interface. Image data is sent
+ either through a parallel interface or through MIPI CSI-2.
+
+allOf:
+ - $ref: ../video-interface-devices.yaml#
+
+properties:
+ compatible:
+ const: galaxycore,gc2145
+
+ reg:
+ const: 0x3c
+
+ clocks:
+ maxItems: 1
+
+ powerdown-gpios:
+ maxItems: 1
+
+ reset-gpios:
+ maxItems: 1
+
+ iovdd-supply:
+ description: Power Supply for I/O circuits (1.7 - 3V).
+
+ avdd-supply:
+ description: Power for analog circuit/sensor array (2.7 - 3V).
+
+ dvdd-supply:
+ description: Power for digital core (1.7 - 1.9V).
+
+ orientation: true
+
+ rotation: true
+
+ port:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ link-frequencies: true
+
+ required:
+ - link-frequencies
+
+ required:
+ - endpoint
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - powerdown-gpios
+ - reset-gpios
+ - iovdd-supply
+ - avdd-supply
+ - dvdd-supply
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ camera@3c {
+ compatible = "galaxycore,gc2145";
+ reg = <0x3c>;
+ clocks = <&clk_ext_camera>;
+ iovdd-supply = <&scmi_v3v3_sw>;
+ avdd-supply = <&scmi_v3v3_sw>;
+ dvdd-supply = <&scmi_v3v3_sw>;
+ powerdown-gpios = <&mcp23017 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
+ reset-gpios = <&mcp23017 4 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
+
+ port {
+ endpoint {
+ remote-endpoint = <&mipid02_0>;
+ data-lanes = <1 2>;
+ link-frequencies = /bits/ 64 <120000000 192000000 240000000>;
+ };
+ };
+ };
+ };
+
+...
--
2.25.1
Add a vendor prefix entry for galaxycore (https://www.gcoreinc.com)
Signed-off-by: Alain Volmat <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Pavel Machek <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 309b94c328c8..b3d751b42927 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -502,6 +502,8 @@ patternProperties:
description: Fujitsu Ltd.
"^fxtec,.*":
description: FX Technology Ltd.
+ "^galaxycore,.*":
+ description: GalaxyCore Inc.
"^gardena,.*":
description: GARDENA GmbH
"^gateway,.*":
--
2.25.1
Addition of support for the Galaxy Core GC2145 XVGA sensor.
The sensor supports both DVP and CSI-2 interfaces however for
the time being only CSI-2 is implemented.
Configurations are currently based on initialization scripts
coming from Galaxy Core and so for that purpose only 3 static
resolutions are supported:
- 640x480
- 1280x720
- 1600x1200
Signed-off-by: Alain Volmat <[email protected]>
---
MAINTAINERS | 8 +
drivers/media/i2c/Kconfig | 10 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/gc2145.c | 1446 ++++++++++++++++++++++++++++++++++++
4 files changed, 1465 insertions(+)
create mode 100644 drivers/media/i2c/gc2145.c
diff --git a/MAINTAINERS b/MAINTAINERS
index c5029341b1d6..43702f86f64c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8760,6 +8760,14 @@ F: kernel/futex/*
F: tools/perf/bench/futex*
F: tools/testing/selftests/futex/
+GALAXYCORE GC2145 SENSOR DRIVER
+M: Alain Volmat <[email protected]>
+L: [email protected]
+S: Maintained
+T: git git://linuxtv.org/media_tree.git
+F: Documentation/devicetree/bindings/media/i2c/galaxycore,gc2145.yaml
+F: drivers/media/i2c/gc2145.c
+
GATEWORKS SYSTEM CONTROLLER (GSC) DRIVER
M: Tim Harvey <[email protected]>
S: Maintained
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 59ee0ca2c978..fc053c834782 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -50,6 +50,16 @@ config VIDEO_AR0521
To compile this driver as a module, choose M here: the
module will be called ar0521.
+config VIDEO_GC2145
+ select V4L2_CCI_I2C
+ tristate "GalaxyCore GC2145 sensor support"
+ help
+ This is a V4L2 sensor-level driver for GalaxyCore GC2145
+ 2 Mpixel camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called gc2145.
+
config VIDEO_HI556
tristate "Hynix Hi-556 sensor support"
help
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index f5010f80a21f..08e7e638dedc 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_VIDEO_DW9719) += dw9719.o
obj-$(CONFIG_VIDEO_DW9768) += dw9768.o
obj-$(CONFIG_VIDEO_DW9807_VCM) += dw9807-vcm.o
obj-$(CONFIG_VIDEO_ET8EK8) += et8ek8/
+obj-$(CONFIG_VIDEO_GC2145) += gc2145.o
obj-$(CONFIG_VIDEO_HI556) += hi556.o
obj-$(CONFIG_VIDEO_HI846) += hi846.o
obj-$(CONFIG_VIDEO_HI847) += hi847.o
diff --git a/drivers/media/i2c/gc2145.c b/drivers/media/i2c/gc2145.c
new file mode 100644
index 000000000000..12d3780b5548
--- /dev/null
+++ b/drivers/media/i2c/gc2145.c
@@ -0,0 +1,1446 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * A V4L2 driver for Galaxycore GC2145 camera.
+ * Copyright (C) 2023, STMicroelectronics SA
+ *
+ * Inspired by the imx219.c driver
+ *
+ * Datasheet v1.0 available at http://files.pine64.org/doc/datasheet/PinebookPro/GC2145%20CSP%20DataSheet%20release%20V1.0_20131201.pdf
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/units.h>
+
+#include <media/mipi-csi2.h>
+#include <media/v4l2-cci.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mediabus.h>
+
+/* Chip ID */
+#define GC2145_CHIP_ID 0x2145
+
+/* Page 0 */
+#define GC2145_REG_EXPOSURE CCI_REG16(0x03)
+#define GC2145_REG_HBLANK CCI_REG16(0x05)
+#define GC2145_REG_VBLANK CCI_REG16(0x07)
+#define GC2145_REG_ROW_START CCI_REG16(0x09)
+#define GC2145_REG_COL_START CCI_REG16(0x0b)
+#define GC2145_REG_WIN_HEIGHT CCI_REG16(0x0d)
+#define GC2145_REG_WIN_WIDTH CCI_REG16(0x0f)
+#define GC2145_REG_ANALOG_MODE1 CCI_REG8(0x17)
+#define GC2145_REG_OUTPUT_FMT CCI_REG8(0x84)
+#define GC2145_REG_SYNC_MODE CCI_REG8(0x86)
+#define GC2145_SYNC_MODE_COL_SWITCH BIT(4)
+#define GC2145_SYNC_MODE_ROW_SWITCH BIT(5)
+#define GC2145_REG_BYPASS_MODE CCI_REG8(0x89)
+#define GC2145_BYPASS_MODE_SWITCH BIT(5)
+#define GC2145_REG_DEBUG_MODE2 CCI_REG8(0x8c)
+#define GC2145_REG_DEBUG_MODE3 CCI_REG8(0x8d)
+#define GC2145_REG_CROP_ENABLE CCI_REG8(0x90)
+#define GC2145_REG_CROP_Y CCI_REG16(0x91)
+#define GC2145_REG_CROP_X CCI_REG16(0x93)
+#define GC2145_REG_CROP_HEIGHT CCI_REG16(0x95)
+#define GC2145_REG_CROP_WIDTH CCI_REG16(0x97)
+#define GC2145_REG_GLOBAL_GAIN CCI_REG8(0xb0)
+#define GC2145_REG_CHIP_ID CCI_REG16(0xf0)
+#define GC2145_REG_PAD_IO CCI_REG8(0xf2)
+#define GC2145_REG_PAGE_SELECT CCI_REG8(0xfe)
+/* Page 3 */
+#define GC2145_REG_DPHY_ANALOG_MODE1 CCI_REG8(0x01)
+#define GC2145_DPHY_MODE_PHY_CLK_EN BIT(0)
+#define GC2145_DPHY_MODE_PHY_LANE0_EN BIT(1)
+#define GC2145_DPHY_MODE_PHY_LANE1_EN BIT(2)
+#define GC2145_DPHY_MODE_PHY_CLK_LANE_P2S_SEL BIT(7)
+#define GC2145_REG_DPHY_ANALOG_MODE2 CCI_REG8(0x02)
+#define GC2145_DPHY_CLK_DIFF(a) ((a) & 0x07)
+#define GC2145_DPHY_LANE0_DIFF(a) (((a) & 0x07) << 4)
+#define GC2145_REG_DPHY_ANALOG_MODE3 CCI_REG8(0x03)
+#define GC2145_DPHY_LANE1_DIFF(a) ((a) & 0x07)
+#define GC2145_DPHY_CLK_DELAY BIT(4)
+#define GC2145_DPHY_LANE0_DELAY BIT(5)
+#define GC2145_DPHY_LANE1_DELAY BIT(6)
+#define GC2145_REG_FIFO_FULL_LVL_LOW CCI_REG8(0x04)
+#define GC2145_REG_FIFO_FULL_LVL_HIGH CCI_REG8(0x05)
+#define GC2145_REG_FIFO_MODE CCI_REG8(0x06)
+#define GC2145_FIFO_MODE_READ_GATE BIT(3)
+#define GC2145_FIFO_MODE_MIPI_CLK_MODULE BIT(7)
+#define GC2145_REG_BUF_CSI2_MODE CCI_REG8(0x10)
+#define GC2145_CSI2_MODE_DOUBLE BIT(0)
+#define GC2145_CSI2_MODE_RAW8 BIT(2)
+#define GC2145_CSI2_MODE_MIPI_EN BIT(4)
+#define GC2145_CSI2_MODE_EN BIT(7)
+#define GC2145_REG_MIPI_DT CCI_REG8(0x11)
+#define GC2145_REG_LWC_LOW CCI_REG8(0x12)
+#define GC2145_REG_LWC_HIGH CCI_REG8(0x13)
+#define GC2145_REG_DPHY_MODE CCI_REG8(0x15)
+#define GC2145_DPHY_MODE_TRIGGER_PROG BIT(4)
+#define GC2145_REG_FIFO_GATE_MODE CCI_REG8(0x17)
+#define GC2145_REG_T_LPX CCI_REG8(0x21)
+#define GC2145_REG_T_CLK_HS_PREPARE CCI_REG8(0x22)
+#define GC2145_REG_T_CLK_ZERO CCI_REG8(0x23)
+#define GC2145_REG_T_CLK_PRE CCI_REG8(0x24)
+#define GC2145_REG_T_CLK_POST CCI_REG8(0x25)
+#define GC2145_REG_T_CLK_TRAIL CCI_REG8(0x26)
+#define GC2145_REG_T_HS_EXIT CCI_REG8(0x27)
+#define GC2145_REG_T_WAKEUP CCI_REG8(0x28)
+#define GC2145_REG_T_HS_PREPARE CCI_REG8(0x29)
+#define GC2145_REG_T_HS_ZERO CCI_REG8(0x2a)
+#define GC2145_REG_T_HS_TRAIL CCI_REG8(0x2b)
+
+/* External clock frequency is 24.0MHz */
+#define GC2145_XCLK_FREQ (24 * HZ_PER_MHZ)
+
+#define GC2145_NATIVE_WIDTH 1616U
+#define GC2145_NATIVE_HEIGHT 1232U
+
+/**
+ * struct gc2145_mode - GC2145 mode description
+ * @width: frame width (in pixels)
+ * @height: frame height (in pixels)
+ * @reg_seq: registers config sequence to enter into the mode
+ * @reg_seq_size: size of the sequence
+ * @pixel_rate: pixel rate associated with the mode
+ * @crop: window area captured
+ * @hblank: default horizontal blanking
+ * @vblank: default vertical blanking
+ * @link_freq_index: index within the link frequency menu
+ */
+struct gc2145_mode {
+ unsigned int width;
+ unsigned int height;
+ const struct cci_reg_sequence *reg_seq;
+ size_t reg_seq_size;
+ unsigned long pixel_rate;
+ struct v4l2_rect crop;
+ unsigned int hblank;
+ unsigned int vblank;
+ unsigned int link_freq_index;
+};
+
+#define GC2145_DEFAULT_EXPOSURE 0x04e2
+#define GC2145_DEFAULT_GLOBAL_GAIN 0x55
+static const struct cci_reg_sequence gc2145_common_regs[] = {
+ {GC2145_REG_PAGE_SELECT, 0x00},
+ /* SH Delay */
+ {CCI_REG8(0x12), 0x2e},
+ /* Flip */
+ {GC2145_REG_ANALOG_MODE1, 0x14},
+ /* Analog Conf */
+ {CCI_REG8(0x18), 0x22}, {CCI_REG8(0x19), 0x0e}, {CCI_REG8(0x1a), 0x01},
+ {CCI_REG8(0x1b), 0x4b}, {CCI_REG8(0x1c), 0x07}, {CCI_REG8(0x1d), 0x10},
+ {CCI_REG8(0x1e), 0x88}, {CCI_REG8(0x1f), 0x78}, {CCI_REG8(0x20), 0x03},
+ {CCI_REG8(0x21), 0x40}, {CCI_REG8(0x22), 0xa0}, {CCI_REG8(0x24), 0x16},
+ {CCI_REG8(0x25), 0x01}, {CCI_REG8(0x26), 0x10}, {CCI_REG8(0x2d), 0x60},
+ {CCI_REG8(0x30), 0x01}, {CCI_REG8(0x31), 0x90}, {CCI_REG8(0x33), 0x06},
+ {CCI_REG8(0x34), 0x01},
+ /* ISP related */
+ {CCI_REG8(0x80), 0x7f}, {CCI_REG8(0x81), 0x26}, {CCI_REG8(0x82), 0xfa},
+ {CCI_REG8(0x83), 0x00}, {CCI_REG8(0x84), 0x02}, {CCI_REG8(0x86), 0x02},
+ {CCI_REG8(0x88), 0x03},
+ {GC2145_REG_BYPASS_MODE, 0x03},
+ {CCI_REG8(0x85), 0x08}, {CCI_REG8(0x8a), 0x00}, {CCI_REG8(0x8b), 0x00},
+ {GC2145_REG_GLOBAL_GAIN, GC2145_DEFAULT_GLOBAL_GAIN},
+ {CCI_REG8(0xc3), 0x00}, {CCI_REG8(0xc4), 0x80}, {CCI_REG8(0xc5), 0x90},
+ {CCI_REG8(0xc6), 0x3b}, {CCI_REG8(0xc7), 0x46},
+ /* BLK */
+ {GC2145_REG_PAGE_SELECT, 0x00},
+ {CCI_REG8(0x40), 0x42}, {CCI_REG8(0x41), 0x00}, {CCI_REG8(0x43), 0x5b},
+ {CCI_REG8(0x5e), 0x00}, {CCI_REG8(0x5f), 0x00}, {CCI_REG8(0x60), 0x00},
+ {CCI_REG8(0x61), 0x00}, {CCI_REG8(0x62), 0x00}, {CCI_REG8(0x63), 0x00},
+ {CCI_REG8(0x64), 0x00}, {CCI_REG8(0x65), 0x00}, {CCI_REG8(0x66), 0x20},
+ {CCI_REG8(0x67), 0x20}, {CCI_REG8(0x68), 0x20}, {CCI_REG8(0x69), 0x20},
+ {CCI_REG8(0x76), 0x00}, {CCI_REG8(0x6a), 0x08}, {CCI_REG8(0x6b), 0x08},
+ {CCI_REG8(0x6c), 0x08}, {CCI_REG8(0x6d), 0x08}, {CCI_REG8(0x6e), 0x08},
+ {CCI_REG8(0x6f), 0x08}, {CCI_REG8(0x70), 0x08}, {CCI_REG8(0x71), 0x08},
+ {CCI_REG8(0x76), 0x00}, {CCI_REG8(0x72), 0xf0}, {CCI_REG8(0x7e), 0x3c},
+ {CCI_REG8(0x7f), 0x00},
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0x48), 0x15}, {CCI_REG8(0x49), 0x00}, {CCI_REG8(0x4b), 0x0b},
+ /* AEC */
+ {GC2145_REG_PAGE_SELECT, 0x00},
+ {GC2145_REG_EXPOSURE, GC2145_DEFAULT_EXPOSURE},
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ {CCI_REG8(0x01), 0x04}, {CCI_REG8(0x02), 0xc0}, {CCI_REG8(0x03), 0x04},
+ {CCI_REG8(0x04), 0x90}, {CCI_REG8(0x05), 0x30}, {CCI_REG8(0x06), 0x90},
+ {CCI_REG8(0x07), 0x30}, {CCI_REG8(0x08), 0x80}, {CCI_REG8(0x09), 0x00},
+ {CCI_REG8(0x0a), 0x82}, {CCI_REG8(0x0b), 0x11}, {CCI_REG8(0x0c), 0x10},
+ {CCI_REG8(0x11), 0x10}, {CCI_REG8(0x13), 0x7b}, {CCI_REG8(0x17), 0x00},
+ {CCI_REG8(0x1c), 0x11}, {CCI_REG8(0x1e), 0x61}, {CCI_REG8(0x1f), 0x35},
+ {CCI_REG8(0x20), 0x40}, {CCI_REG8(0x22), 0x40}, {CCI_REG8(0x23), 0x20},
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0x0f), 0x04},
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ {CCI_REG8(0x12), 0x35}, {CCI_REG8(0x15), 0xb0}, {CCI_REG8(0x10), 0x31},
+ {CCI_REG8(0x3e), 0x28}, {CCI_REG8(0x3f), 0xb0}, {CCI_REG8(0x40), 0x90},
+ {CCI_REG8(0x41), 0x0f},
+ /* INTPEE */
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0x90), 0x6c}, {CCI_REG8(0x91), 0x03}, {CCI_REG8(0x92), 0xcb},
+ {CCI_REG8(0x94), 0x33}, {CCI_REG8(0x95), 0x84}, {CCI_REG8(0x97), 0x65},
+ {CCI_REG8(0xa2), 0x11},
+ /* DNDD */
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0x80), 0xc1}, {CCI_REG8(0x81), 0x08}, {CCI_REG8(0x82), 0x05},
+ {CCI_REG8(0x83), 0x08}, {CCI_REG8(0x84), 0x0a}, {CCI_REG8(0x86), 0xf0},
+ {CCI_REG8(0x87), 0x50}, {CCI_REG8(0x88), 0x15}, {CCI_REG8(0x89), 0xb0},
+ {CCI_REG8(0x8a), 0x30}, {CCI_REG8(0x8b), 0x10},
+ /* ASDE */
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ {CCI_REG8(0x21), 0x04},
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0xa3), 0x50}, {CCI_REG8(0xa4), 0x20}, {CCI_REG8(0xa5), 0x40},
+ {CCI_REG8(0xa6), 0x80}, {CCI_REG8(0xab), 0x40}, {CCI_REG8(0xae), 0x0c},
+ {CCI_REG8(0xb3), 0x46}, {CCI_REG8(0xb4), 0x64}, {CCI_REG8(0xb6), 0x38},
+ {CCI_REG8(0xb7), 0x01}, {CCI_REG8(0xb9), 0x2b}, {CCI_REG8(0x3c), 0x04},
+ {CCI_REG8(0x3d), 0x15}, {CCI_REG8(0x4b), 0x06}, {CCI_REG8(0x4c), 0x20},
+ /* Gamma */
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0x10), 0x09}, {CCI_REG8(0x11), 0x0d}, {CCI_REG8(0x12), 0x13},
+ {CCI_REG8(0x13), 0x19}, {CCI_REG8(0x14), 0x27}, {CCI_REG8(0x15), 0x37},
+ {CCI_REG8(0x16), 0x45}, {CCI_REG8(0x17), 0x53}, {CCI_REG8(0x18), 0x69},
+ {CCI_REG8(0x19), 0x7d}, {CCI_REG8(0x1a), 0x8f}, {CCI_REG8(0x1b), 0x9d},
+ {CCI_REG8(0x1c), 0xa9}, {CCI_REG8(0x1d), 0xbd}, {CCI_REG8(0x1e), 0xcd},
+ {CCI_REG8(0x1f), 0xd9}, {CCI_REG8(0x20), 0xe3}, {CCI_REG8(0x21), 0xea},
+ {CCI_REG8(0x22), 0xef}, {CCI_REG8(0x23), 0xf5}, {CCI_REG8(0x24), 0xf9},
+ {CCI_REG8(0x25), 0xff},
+ {GC2145_REG_PAGE_SELECT, 0x00},
+ {CCI_REG8(0xc6), 0x20}, {CCI_REG8(0xc7), 0x2b},
+ /* Gamma 2 */
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0x26), 0x0f}, {CCI_REG8(0x27), 0x14}, {CCI_REG8(0x28), 0x19},
+ {CCI_REG8(0x29), 0x1e}, {CCI_REG8(0x2a), 0x27}, {CCI_REG8(0x2b), 0x33},
+ {CCI_REG8(0x2c), 0x3b}, {CCI_REG8(0x2d), 0x45}, {CCI_REG8(0x2e), 0x59},
+ {CCI_REG8(0x2f), 0x69}, {CCI_REG8(0x30), 0x7c}, {CCI_REG8(0x31), 0x89},
+ {CCI_REG8(0x32), 0x98}, {CCI_REG8(0x33), 0xae}, {CCI_REG8(0x34), 0xc0},
+ {CCI_REG8(0x35), 0xcf}, {CCI_REG8(0x36), 0xda}, {CCI_REG8(0x37), 0xe2},
+ {CCI_REG8(0x38), 0xe9}, {CCI_REG8(0x39), 0xf3}, {CCI_REG8(0x3a), 0xf9},
+ {CCI_REG8(0x3b), 0xff},
+ /* YCP */
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0xd1), 0x32}, {CCI_REG8(0xd2), 0x32}, {CCI_REG8(0xd3), 0x40},
+ {CCI_REG8(0xd6), 0xf0}, {CCI_REG8(0xd7), 0x10}, {CCI_REG8(0xd8), 0xda},
+ {CCI_REG8(0xdd), 0x14}, {CCI_REG8(0xde), 0x86}, {CCI_REG8(0xed), 0x80},
+ {CCI_REG8(0xee), 0x00}, {CCI_REG8(0xef), 0x3f}, {CCI_REG8(0xd8), 0xd8},
+ /* ABS */
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ {CCI_REG8(0x9f), 0x40},
+ /* LSC */
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ {CCI_REG8(0xc2), 0x14}, {CCI_REG8(0xc3), 0x0d}, {CCI_REG8(0xc4), 0x0c},
+ {CCI_REG8(0xc8), 0x15}, {CCI_REG8(0xc9), 0x0d}, {CCI_REG8(0xca), 0x0a},
+ {CCI_REG8(0xbc), 0x24}, {CCI_REG8(0xbd), 0x10}, {CCI_REG8(0xbe), 0x0b},
+ {CCI_REG8(0xb6), 0x25}, {CCI_REG8(0xb7), 0x16}, {CCI_REG8(0xb8), 0x15},
+ {CCI_REG8(0xc5), 0x00}, {CCI_REG8(0xc6), 0x00}, {CCI_REG8(0xc7), 0x00},
+ {CCI_REG8(0xcb), 0x00}, {CCI_REG8(0xcc), 0x00}, {CCI_REG8(0xcd), 0x00},
+ {CCI_REG8(0xbf), 0x07}, {CCI_REG8(0xc0), 0x00}, {CCI_REG8(0xc1), 0x00},
+ {CCI_REG8(0xb9), 0x00}, {CCI_REG8(0xba), 0x00}, {CCI_REG8(0xbb), 0x00},
+ {CCI_REG8(0xaa), 0x01}, {CCI_REG8(0xab), 0x01}, {CCI_REG8(0xac), 0x00},
+ {CCI_REG8(0xad), 0x05}, {CCI_REG8(0xae), 0x06}, {CCI_REG8(0xaf), 0x0e},
+ {CCI_REG8(0xb0), 0x0b}, {CCI_REG8(0xb1), 0x07}, {CCI_REG8(0xb2), 0x06},
+ {CCI_REG8(0xb3), 0x17}, {CCI_REG8(0xb4), 0x0e}, {CCI_REG8(0xb5), 0x0e},
+ {CCI_REG8(0xd0), 0x09}, {CCI_REG8(0xd1), 0x00}, {CCI_REG8(0xd2), 0x00},
+ {CCI_REG8(0xd6), 0x08}, {CCI_REG8(0xd7), 0x00}, {CCI_REG8(0xd8), 0x00},
+ {CCI_REG8(0xd9), 0x00}, {CCI_REG8(0xda), 0x00}, {CCI_REG8(0xdb), 0x00},
+ {CCI_REG8(0xd3), 0x0a}, {CCI_REG8(0xd4), 0x00}, {CCI_REG8(0xd5), 0x00},
+ {CCI_REG8(0xa4), 0x00}, {CCI_REG8(0xa5), 0x00}, {CCI_REG8(0xa6), 0x77},
+ {CCI_REG8(0xa7), 0x77}, {CCI_REG8(0xa8), 0x77}, {CCI_REG8(0xa9), 0x77},
+ {CCI_REG8(0xa1), 0x80}, {CCI_REG8(0xa2), 0x80},
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ {CCI_REG8(0xdf), 0x0d}, {CCI_REG8(0xdc), 0x25}, {CCI_REG8(0xdd), 0x30},
+ {CCI_REG8(0xe0), 0x77}, {CCI_REG8(0xe1), 0x80}, {CCI_REG8(0xe2), 0x77},
+ {CCI_REG8(0xe3), 0x90}, {CCI_REG8(0xe6), 0x90}, {CCI_REG8(0xe7), 0xa0},
+ {CCI_REG8(0xe8), 0x90}, {CCI_REG8(0xe9), 0xa0},
+ /* AWB */
+ /* measure window */
+ {GC2145_REG_PAGE_SELECT, 0x00},
+ {CCI_REG8(0xec), 0x06}, {CCI_REG8(0xed), 0x04}, {CCI_REG8(0xee), 0x60},
+ {CCI_REG8(0xef), 0x90}, {CCI_REG8(0xb6), 0x01},
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ {CCI_REG8(0x4f), 0x00}, {CCI_REG8(0x4f), 0x00}, {CCI_REG8(0x4b), 0x01},
+ {CCI_REG8(0x4f), 0x00},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x71}, {CCI_REG8(0x4e), 0x01},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x91}, {CCI_REG8(0x4e), 0x01},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x70}, {CCI_REG8(0x4e), 0x01},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x90}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xb0}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x8f}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x6f}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xaf}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xd0}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xf0}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xcf}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xef}, {CCI_REG8(0x4e), 0x02},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x6e}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x8e}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xae}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xce}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x4d}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x6d}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x8d}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xad}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xcd}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x4c}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x6c}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x8c}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xac}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xcc}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xcb}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x4b}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x6b}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x8b}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xab}, {CCI_REG8(0x4e), 0x03},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x8a}, {CCI_REG8(0x4e), 0x04},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xaa}, {CCI_REG8(0x4e), 0x04},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xca}, {CCI_REG8(0x4e), 0x04},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xca}, {CCI_REG8(0x4e), 0x04},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xc9}, {CCI_REG8(0x4e), 0x04},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x8a}, {CCI_REG8(0x4e), 0x04},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0x89}, {CCI_REG8(0x4e), 0x04},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xa9}, {CCI_REG8(0x4e), 0x04},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x0b}, {CCI_REG8(0x4e), 0x05},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x0a}, {CCI_REG8(0x4e), 0x05},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xeb}, {CCI_REG8(0x4e), 0x05},
+ {CCI_REG8(0x4c), 0x01}, {CCI_REG8(0x4d), 0xea}, {CCI_REG8(0x4e), 0x05},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x09}, {CCI_REG8(0x4e), 0x05},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x29}, {CCI_REG8(0x4e), 0x05},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x2a}, {CCI_REG8(0x4e), 0x05},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x4a}, {CCI_REG8(0x4e), 0x05},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x8a}, {CCI_REG8(0x4e), 0x06},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x49}, {CCI_REG8(0x4e), 0x06},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x69}, {CCI_REG8(0x4e), 0x06},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x89}, {CCI_REG8(0x4e), 0x06},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xa9}, {CCI_REG8(0x4e), 0x06},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x48}, {CCI_REG8(0x4e), 0x06},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x68}, {CCI_REG8(0x4e), 0x06},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0x69}, {CCI_REG8(0x4e), 0x06},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xca}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xc9}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xe9}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x03}, {CCI_REG8(0x4d), 0x09}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xc8}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xe8}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xa7}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xc7}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x02}, {CCI_REG8(0x4d), 0xe7}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4c), 0x03}, {CCI_REG8(0x4d), 0x07}, {CCI_REG8(0x4e), 0x07},
+ {CCI_REG8(0x4f), 0x01},
+ {CCI_REG8(0x50), 0x80}, {CCI_REG8(0x51), 0xa8}, {CCI_REG8(0x52), 0x47},
+ {CCI_REG8(0x53), 0x38}, {CCI_REG8(0x54), 0xc7}, {CCI_REG8(0x56), 0x0e},
+ {CCI_REG8(0x58), 0x08}, {CCI_REG8(0x5b), 0x00}, {CCI_REG8(0x5c), 0x74},
+ {CCI_REG8(0x5d), 0x8b}, {CCI_REG8(0x61), 0xdb}, {CCI_REG8(0x62), 0xb8},
+ {CCI_REG8(0x63), 0x86}, {CCI_REG8(0x64), 0xc0}, {CCI_REG8(0x65), 0x04},
+ {CCI_REG8(0x67), 0xa8}, {CCI_REG8(0x68), 0xb0}, {CCI_REG8(0x69), 0x00},
+ {CCI_REG8(0x6a), 0xa8}, {CCI_REG8(0x6b), 0xb0}, {CCI_REG8(0x6c), 0xaf},
+ {CCI_REG8(0x6d), 0x8b}, {CCI_REG8(0x6e), 0x50}, {CCI_REG8(0x6f), 0x18},
+ {CCI_REG8(0x73), 0xf0}, {CCI_REG8(0x70), 0x0d}, {CCI_REG8(0x71), 0x60},
+ {CCI_REG8(0x72), 0x80}, {CCI_REG8(0x74), 0x01}, {CCI_REG8(0x75), 0x01},
+ {CCI_REG8(0x7f), 0x0c}, {CCI_REG8(0x76), 0x70}, {CCI_REG8(0x77), 0x58},
+ {CCI_REG8(0x78), 0xa0}, {CCI_REG8(0x79), 0x5e}, {CCI_REG8(0x7a), 0x54},
+ {CCI_REG8(0x7b), 0x58},
+ /* CC */
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0xc0), 0x01}, {CCI_REG8(0xc1), 0x44}, {CCI_REG8(0xc2), 0xfd},
+ {CCI_REG8(0xc3), 0x04}, {CCI_REG8(0xc4), 0xf0}, {CCI_REG8(0xc5), 0x48},
+ {CCI_REG8(0xc6), 0xfd}, {CCI_REG8(0xc7), 0x46}, {CCI_REG8(0xc8), 0xfd},
+ {CCI_REG8(0xc9), 0x02}, {CCI_REG8(0xca), 0xe0}, {CCI_REG8(0xcb), 0x45},
+ {CCI_REG8(0xcc), 0xec}, {CCI_REG8(0xcd), 0x48}, {CCI_REG8(0xce), 0xf0},
+ {CCI_REG8(0xcf), 0xf0}, {CCI_REG8(0xe3), 0x0c}, {CCI_REG8(0xe4), 0x4b},
+ {CCI_REG8(0xe5), 0xe0},
+ /* ABS */
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ {CCI_REG8(0x9f), 0x40},
+ /* Dark sun */
+ {GC2145_REG_PAGE_SELECT, 0x02},
+ {CCI_REG8(0x40), 0xbf}, {CCI_REG8(0x46), 0xcf},
+};
+
+#define GC2145_640_480_PIXELRATE 30000000
+#define GC2145_640_480_LINKFREQ 120000000
+#define GC2145_640_480_HBLANK 0x0130
+#define GC2145_640_480_VBLANK 0x000c
+static const struct cci_reg_sequence gc2145_mode_640_480_regs[] = {
+ {GC2145_REG_PAGE_SELECT, 0xf0}, {GC2145_REG_PAGE_SELECT, 0xf0},
+ {GC2145_REG_PAGE_SELECT, 0xf0}, {CCI_REG8(0xfc), 0x06},
+ {CCI_REG8(0xf6), 0x00}, {CCI_REG8(0xf7), 0x1d}, {CCI_REG8(0xf8), 0x86},
+ {CCI_REG8(0xfa), 0x00}, {CCI_REG8(0xf9), 0x8e},
+ /* Disable PAD IO */
+ {GC2145_REG_PAD_IO, 0x00},
+ {GC2145_REG_PAGE_SELECT, 0x00},
+ /* Row/Col start - 0/0 */
+ {GC2145_REG_ROW_START, 0x0000},
+ {GC2145_REG_COL_START, 0x0000},
+ /* Window size 1216/1618 */
+ {GC2145_REG_WIN_HEIGHT, 0x04c0},
+ {GC2145_REG_WIN_WIDTH, 0x0652},
+ /* Scalar more */
+ {CCI_REG8(0xfd), 0x01}, {CCI_REG8(0xfa), 0x00},
+ /* Crop 640-480@0-0 */
+ {GC2145_REG_CROP_ENABLE, 0x01},
+ {GC2145_REG_CROP_Y, 0x0000},
+ {GC2145_REG_CROP_X, 0x0000},
+ {GC2145_REG_CROP_HEIGHT, 0x01e0},
+ {GC2145_REG_CROP_WIDTH, 0x0280},
+ /* Subsampling configuration */
+ {CCI_REG8(0x99), 0x55}, {CCI_REG8(0x9a), 0x06}, {CCI_REG8(0x9b), 0x01},
+ {CCI_REG8(0x9c), 0x23}, {CCI_REG8(0x9d), 0x00}, {CCI_REG8(0x9e), 0x00},
+ {CCI_REG8(0x9f), 0x01}, {CCI_REG8(0xa0), 0x23}, {CCI_REG8(0xa1), 0x00},
+ {CCI_REG8(0xa2), 0x00},
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ /* AEC anti-flicker */
+ {CCI_REG16(0x25), 0x0175},
+ /* AEC exposure level 1-5 */
+ {CCI_REG16(0x27), 0x045f}, {CCI_REG16(0x29), 0x045f},
+ {CCI_REG16(0x2b), 0x045f}, {CCI_REG16(0x2d), 0x045f},
+};
+
+#define GC2145_1280_720_PIXELRATE 48000000
+#define GC2145_1280_720_LINKFREQ 192000000
+#define GC2145_1280_720_HBLANK 0x0156
+#define GC2145_1280_720_VBLANK 0x0011
+static const struct cci_reg_sequence gc2145_mode_1280_720_regs[] = {
+ {GC2145_REG_PAGE_SELECT, 0xf0}, {GC2145_REG_PAGE_SELECT, 0xf0},
+ {GC2145_REG_PAGE_SELECT, 0xf0}, {CCI_REG8(0xfc), 0x06},
+ {CCI_REG8(0xf6), 0x00}, {CCI_REG8(0xf7), 0x1d}, {CCI_REG8(0xf8), 0x83},
+ {CCI_REG8(0xfa), 0x00}, {CCI_REG8(0xf9), 0x8e},
+ /* Disable PAD IO */
+ {GC2145_REG_PAD_IO, 0x00},
+ {GC2145_REG_PAGE_SELECT, 0x00},
+ /* Row/Col start - 240/160 */
+ {GC2145_REG_ROW_START, 0x00f0},
+ {GC2145_REG_COL_START, 0x00a0},
+ /* Window size 736/1296 */
+ {GC2145_REG_WIN_HEIGHT, 0x02e0},
+ {GC2145_REG_WIN_WIDTH, 0x0510},
+ /* Crop 1280-720@0-0 */
+ {GC2145_REG_CROP_ENABLE, 0x01},
+ {GC2145_REG_CROP_Y, 0x0000},
+ {GC2145_REG_CROP_X, 0x0000},
+ {GC2145_REG_CROP_HEIGHT, 0x02d0},
+ {GC2145_REG_CROP_WIDTH, 0x0500},
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ /* AEC anti-flicker */
+ {CCI_REG16(0x25), 0x00e6},
+ /* AEC exposure level 1-5 */
+ {CCI_REG16(0x27), 0x02b2}, {CCI_REG16(0x29), 0x02b2},
+ {CCI_REG16(0x2b), 0x02b2}, {CCI_REG16(0x2d), 0x02b2},
+};
+
+#define GC2145_1600_1200_PIXELRATE 60000000
+#define GC2145_1600_1200_LINKFREQ 240000000
+#define GC2145_1600_1200_HBLANK 0x0156
+#define GC2145_1600_1200_VBLANK 0x0010
+static const struct cci_reg_sequence gc2145_mode_1600_1200_regs[] = {
+ {GC2145_REG_PAGE_SELECT, 0xf0}, {GC2145_REG_PAGE_SELECT, 0xf0},
+ {GC2145_REG_PAGE_SELECT, 0xf0}, {CCI_REG8(0xfc), 0x06},
+ {CCI_REG8(0xf6), 0x00}, {CCI_REG8(0xf7), 0x1d}, {CCI_REG8(0xf8), 0x84},
+ {CCI_REG8(0xfa), 0x00}, {CCI_REG8(0xf9), 0x8e},
+ /* Disable PAD IO */
+ {GC2145_REG_PAD_IO, 0x00},
+ {GC2145_REG_PAGE_SELECT, 0x00},
+ /* Row/Col start - 0/0 */
+ {GC2145_REG_ROW_START, 0x0000},
+ {GC2145_REG_COL_START, 0x0000},
+ /* Window size: 1216/1618 */
+ {GC2145_REG_WIN_HEIGHT, 0x04c0},
+ {GC2145_REG_WIN_WIDTH, 0x0652},
+ /* Crop 1600-1200@0-0 */
+ {GC2145_REG_CROP_ENABLE, 0x01},
+ {GC2145_REG_CROP_Y, 0x0000},
+ {GC2145_REG_CROP_X, 0x0000},
+ {GC2145_REG_CROP_HEIGHT, 0x04b0},
+ {GC2145_REG_CROP_WIDTH, 0x0640},
+ {GC2145_REG_PAGE_SELECT, 0x01},
+ /* AEC anti-flicker */
+ {CCI_REG16(0x25), 0x00fa},
+ /* AEC exposure level 1-5 */
+ {CCI_REG16(0x27), 0x04e2}, {CCI_REG16(0x29), 0x04e2},
+ {CCI_REG16(0x2b), 0x04e2}, {CCI_REG16(0x2d), 0x04e2},
+};
+
+static const s64 gc2145_link_freq_menu[] = {
+ GC2145_640_480_LINKFREQ,
+ GC2145_1280_720_LINKFREQ,
+ GC2145_1600_1200_LINKFREQ,
+};
+
+/* Regulators supplies */
+static const char * const gc2145_supply_name[] = {
+ "iovdd", /* Digital I/O (1.7-3V) suppply */
+ "avdd", /* Analog (2.7-3V) supply */
+ "dvdd", /* Digital Core (1.7-1.9V) supply */
+};
+
+#define GC2145_NUM_SUPPLIES ARRAY_SIZE(gc2145_supply_name)
+
+/* Mode configs */
+#define GC2145_MODE_640X480 0
+#define GC2145_MODE_1280X720 1
+#define GC2145_MODE_1600X1200 2
+static const struct gc2145_mode supported_modes[] = {
+ {
+ /* 640x480 30fps mode */
+ .width = 640,
+ .height = 480,
+ .reg_seq = gc2145_mode_640_480_regs,
+ .reg_seq_size = ARRAY_SIZE(gc2145_mode_640_480_regs),
+ .pixel_rate = GC2145_640_480_PIXELRATE,
+ .crop = {
+ .top = 0,
+ .left = 0,
+ .width = 640,
+ .height = 480,
+ },
+ .hblank = GC2145_640_480_HBLANK,
+ .vblank = GC2145_640_480_VBLANK,
+ .link_freq_index = GC2145_MODE_640X480,
+ },
+ {
+ /* 1280x720 30fps mode */
+ .width = 1280,
+ .height = 720,
+ .reg_seq = gc2145_mode_1280_720_regs,
+ .reg_seq_size = ARRAY_SIZE(gc2145_mode_1280_720_regs),
+ .pixel_rate = GC2145_1280_720_PIXELRATE,
+ .crop = {
+ .top = 160,
+ .left = 240,
+ .width = 1280,
+ .height = 720,
+ },
+ .hblank = GC2145_1280_720_HBLANK,
+ .vblank = GC2145_1280_720_VBLANK,
+ .link_freq_index = GC2145_MODE_1280X720,
+ },
+ {
+ /* 1600x1200 20fps mode */
+ .width = 1600,
+ .height = 1200,
+ .reg_seq = gc2145_mode_1600_1200_regs,
+ .reg_seq_size = ARRAY_SIZE(gc2145_mode_1600_1200_regs),
+ .pixel_rate = GC2145_1600_1200_PIXELRATE,
+ .crop = {
+ .top = 0,
+ .left = 0,
+ .width = 1600,
+ .height = 1200,
+ },
+ .hblank = GC2145_1600_1200_HBLANK,
+ .vblank = GC2145_1600_1200_VBLANK,
+ .link_freq_index = GC2145_MODE_1600X1200,
+ },
+};
+
+/**
+ * struct gc2145_format - GC2145 pixel format description
+ * @code: media bus (MBUS) associated code
+ * @datatype: MIPI CSI2 data type
+ * @output_fmt: GC2145 output format
+ * @switch_bit: GC2145 first/second switch
+ */
+struct gc2145_format {
+ unsigned int code;
+ unsigned char datatype;
+ unsigned char output_fmt;
+ bool switch_bit;
+};
+
+/* All supported formats */
+static const struct gc2145_format supported_formats[] = {
+ {
+ .code = MEDIA_BUS_FMT_UYVY8_1X16,
+ .datatype = MIPI_CSI2_DT_YUV422_8B,
+ .output_fmt = 0x00,
+ },
+ {
+ .code = MEDIA_BUS_FMT_VYUY8_1X16,
+ .datatype = MIPI_CSI2_DT_YUV422_8B,
+ .output_fmt = 0x01,
+ },
+ {
+ .code = MEDIA_BUS_FMT_YUYV8_1X16,
+ .datatype = MIPI_CSI2_DT_YUV422_8B,
+ .output_fmt = 0x02,
+ },
+ {
+ .code = MEDIA_BUS_FMT_YVYU8_1X16,
+ .datatype = MIPI_CSI2_DT_YUV422_8B,
+ .output_fmt = 0x03,
+ },
+ {
+ .code = MEDIA_BUS_FMT_RGB565_1X16,
+ .datatype = MIPI_CSI2_DT_RGB565,
+ .output_fmt = 0x06,
+ .switch_bit = true,
+ },
+};
+
+struct gc2145_ctrls {
+ struct v4l2_ctrl_handler handler;
+ struct v4l2_ctrl *pixel_rate;
+ struct v4l2_ctrl *link_freq;
+ struct v4l2_ctrl *test_pattern;
+ struct v4l2_ctrl *hflip;
+ struct v4l2_ctrl *vflip;
+ struct v4l2_ctrl *hblank;
+ struct v4l2_ctrl *vblank;
+};
+
+struct gc2145 {
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+
+ struct regmap *regmap;
+ struct clk *xclk;
+
+ struct gpio_desc *reset_gpio;
+ struct gpio_desc *powerdown_gpio;
+ struct regulator_bulk_data supplies[GC2145_NUM_SUPPLIES];
+
+ /* V4L2 controls */
+ struct gc2145_ctrls ctrls;
+
+ /* Current mode */
+ const struct gc2145_mode *mode;
+};
+
+static inline struct gc2145 *to_gc2145(struct v4l2_subdev *_sd)
+{
+ return container_of(_sd, struct gc2145, sd);
+}
+
+static inline struct v4l2_subdev *gc2145_ctrl_to_sd(struct v4l2_ctrl *ctrl)
+{
+ return &container_of(ctrl->handler, struct gc2145,
+ ctrls.handler)->sd;
+}
+
+static const struct gc2145_format *
+gc2145_get_format_code(struct gc2145 *gc2145, u32 code)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(supported_formats); i++) {
+ if (supported_formats[i].code == code)
+ break;
+ }
+
+ if (i >= ARRAY_SIZE(supported_formats))
+ i = 0;
+
+ return &supported_formats[i];
+}
+
+static void gc2145_update_pad_format(struct gc2145 *gc2145,
+ const struct gc2145_mode *mode,
+ struct v4l2_mbus_framefmt *fmt, u32 code)
+{
+ fmt->code = code;
+ fmt->width = mode->width;
+ fmt->height = mode->height;
+ fmt->field = V4L2_FIELD_NONE;
+ fmt->colorspace = V4L2_COLORSPACE_SRGB;
+ fmt->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT;
+ fmt->quantization = V4L2_QUANTIZATION_DEFAULT;
+ fmt->xfer_func = V4L2_XFER_FUNC_DEFAULT;
+}
+
+static int gc2145_init_cfg(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct gc2145 *gc2145 = to_gc2145(sd);
+ struct v4l2_mbus_framefmt *format;
+ struct v4l2_rect *crop;
+
+ /* Initialize pad format */
+ format = v4l2_subdev_state_get_format(state, 0);
+ gc2145_update_pad_format(gc2145, &supported_modes[0], format,
+ MEDIA_BUS_FMT_RGB565_1X16);
+
+ /* Initialize crop rectangle. */
+ crop = v4l2_subdev_state_get_crop(state, 0);
+ *crop = supported_modes[0].crop;
+
+ return 0;
+}
+
+static int gc2145_get_selection(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_selection *sel)
+{
+ switch (sel->target) {
+ case V4L2_SEL_TGT_CROP:
+ sel->r = *v4l2_subdev_state_get_crop(sd_state, 0);
+ return 0;
+
+ case V4L2_SEL_TGT_NATIVE_SIZE:
+ sel->r.top = 0;
+ sel->r.left = 0;
+ sel->r.width = GC2145_NATIVE_WIDTH;
+ sel->r.height = GC2145_NATIVE_HEIGHT;
+
+ return 0;
+
+ case V4L2_SEL_TGT_CROP_DEFAULT:
+ case V4L2_SEL_TGT_CROP_BOUNDS:
+ sel->r.top = 0;
+ sel->r.left = 0;
+ sel->r.width = 1600;
+ sel->r.height = 1200;
+
+ return 0;
+ }
+
+ return -EINVAL;
+}
+
+static int gc2145_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->index >= ARRAY_SIZE(supported_formats))
+ return -EINVAL;
+
+ code->code = supported_formats[code->index].code;
+ return 0;
+}
+
+static int gc2145_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ struct gc2145 *gc2145 = to_gc2145(sd);
+ const struct gc2145_format *gc2145_format;
+ u32 code;
+
+ if (fse->index >= ARRAY_SIZE(supported_modes))
+ return -EINVAL;
+
+ gc2145_format = gc2145_get_format_code(gc2145, fse->code);
+ code = gc2145_format->code;
+ if (fse->code != code)
+ return -EINVAL;
+
+ fse->min_width = supported_modes[fse->index].width;
+ fse->max_width = fse->min_width;
+ fse->min_height = supported_modes[fse->index].height;
+ fse->max_height = fse->min_height;
+
+ return 0;
+}
+
+static int gc2145_set_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_format *fmt)
+{
+ struct gc2145 *gc2145 = to_gc2145(sd);
+ const struct gc2145_mode *mode;
+ const struct gc2145_format *gc2145_fmt;
+ struct v4l2_mbus_framefmt *framefmt;
+ struct gc2145_ctrls *ctrls = &gc2145->ctrls;
+ struct v4l2_rect *crop;
+
+ gc2145_fmt = gc2145_get_format_code(gc2145, fmt->format.code);
+ mode = v4l2_find_nearest_size(supported_modes,
+ ARRAY_SIZE(supported_modes),
+ width, height,
+ fmt->format.width, fmt->format.height);
+
+ gc2145_update_pad_format(gc2145, mode, &fmt->format, gc2145_fmt->code);
+ framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
+ if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
+ gc2145->mode = mode;
+ /* Update pixel_rate based on the mode */
+ __v4l2_ctrl_s_ctrl_int64(ctrls->pixel_rate, mode->pixel_rate);
+ /* Update link_freq based on the mode */
+ __v4l2_ctrl_s_ctrl(ctrls->link_freq, mode->link_freq_index);
+ /* Update hblank/vblank based on the mode */
+ __v4l2_ctrl_s_ctrl(ctrls->hblank, mode->hblank);
+ __v4l2_ctrl_s_ctrl(ctrls->vblank, mode->vblank);
+ }
+ *framefmt = fmt->format;
+ crop = v4l2_subdev_state_get_crop(sd_state, fmt->pad);
+ *crop = mode->crop;
+
+ return 0;
+}
+
+static const struct cci_reg_sequence gc2145_common_mipi_regs[] = {
+ {GC2145_REG_PAGE_SELECT, 0x03},
+ {GC2145_REG_DPHY_ANALOG_MODE1, GC2145_DPHY_MODE_PHY_CLK_EN |
+ GC2145_DPHY_MODE_PHY_LANE0_EN |
+ GC2145_DPHY_MODE_PHY_LANE1_EN |
+ GC2145_DPHY_MODE_PHY_CLK_LANE_P2S_SEL},
+ {GC2145_REG_DPHY_ANALOG_MODE2, GC2145_DPHY_CLK_DIFF(2) |
+ GC2145_DPHY_LANE0_DIFF(2)},
+ {GC2145_REG_DPHY_ANALOG_MODE3, GC2145_DPHY_LANE1_DIFF(0) |
+ GC2145_DPHY_CLK_DELAY},
+ {GC2145_REG_FIFO_MODE, GC2145_FIFO_MODE_READ_GATE |
+ GC2145_FIFO_MODE_MIPI_CLK_MODULE},
+ {GC2145_REG_DPHY_MODE, GC2145_DPHY_MODE_TRIGGER_PROG},
+ /* Clock & Data lanes timing */
+ {GC2145_REG_T_LPX, 0x10},
+ {GC2145_REG_T_CLK_HS_PREPARE, 0x04}, {GC2145_REG_T_CLK_ZERO, 0x10},
+ {GC2145_REG_T_CLK_PRE, 0x10}, {GC2145_REG_T_CLK_POST, 0x10},
+ {GC2145_REG_T_CLK_TRAIL, 0x05},
+ {GC2145_REG_T_HS_PREPARE, 0x03}, {GC2145_REG_T_HS_ZERO, 0x0a},
+ {GC2145_REG_T_HS_TRAIL, 0x06},
+};
+
+static int gc2145_config_mipi_mode(struct gc2145 *gc2145,
+ const struct gc2145_format *gc2145_format)
+{
+ u16 lwc, fifo_full_lvl;
+ int ret = 0;
+
+ /* Common MIPI settings */
+ cci_multi_reg_write(gc2145->regmap, gc2145_common_mipi_regs,
+ ARRAY_SIZE(gc2145_common_mipi_regs), &ret);
+
+ /*
+ * Adjust the MIPI buffer settings.
+ * For YUV/RGB, LWC = image width * 2
+ * For RAW8, LWC = image width
+ * For RAW10, LWC = image width * 1.25
+ */
+ lwc = gc2145->mode->width * 2;
+ cci_write(gc2145->regmap, GC2145_REG_LWC_HIGH, lwc >> 8, &ret);
+ cci_write(gc2145->regmap, GC2145_REG_LWC_LOW, lwc & 0xff, &ret);
+
+ /*
+ * Adjust the MIPI FIFO Full Level
+ * 640x480 RGB: 0x0190
+ * 1280x720 / 1600x1200 (aka no scaler) non RAW: 0x0001
+ * 1600x1200 RAW: 0x0190
+ */
+ if (gc2145->mode->width == 1280 || gc2145->mode->width == 1600)
+ fifo_full_lvl = 0x0001;
+ else
+ fifo_full_lvl = 0x0190;
+
+ cci_write(gc2145->regmap, GC2145_REG_FIFO_FULL_LVL_HIGH,
+ fifo_full_lvl >> 8, &ret);
+ cci_write(gc2145->regmap, GC2145_REG_FIFO_FULL_LVL_LOW,
+ fifo_full_lvl & 0xff, &ret);
+
+ /*
+ * Set the FIFO gate mode / MIPI wdiv set:
+ * 0xf1 in case of RAW mode and 0xf0 otherwise
+ */
+ cci_write(gc2145->regmap, GC2145_REG_FIFO_GATE_MODE, 0xf0, &ret);
+
+ /* Set the MIPI data type */
+ cci_write(gc2145->regmap, GC2145_REG_MIPI_DT,
+ gc2145_format->datatype, &ret);
+
+ /* Configure mode and enable CSI */
+ cci_write(gc2145->regmap, GC2145_REG_BUF_CSI2_MODE,
+ GC2145_CSI2_MODE_RAW8 | GC2145_CSI2_MODE_DOUBLE |
+ GC2145_CSI2_MODE_EN | GC2145_CSI2_MODE_MIPI_EN, &ret);
+
+ return ret;
+}
+
+static int gc2145_start_streaming(struct gc2145 *gc2145,
+ struct v4l2_subdev_state *state)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&gc2145->sd);
+ const struct gc2145_format *gc2145_format;
+ struct v4l2_mbus_framefmt *fmt;
+ int ret;
+
+ ret = pm_runtime_resume_and_get(&client->dev);
+ if (ret < 0)
+ return ret;
+
+ /* Apply default values of current mode */
+ cci_multi_reg_write(gc2145->regmap, gc2145->mode->reg_seq,
+ gc2145->mode->reg_seq_size, &ret);
+ cci_multi_reg_write(gc2145->regmap, gc2145_common_regs,
+ ARRAY_SIZE(gc2145_common_regs), &ret);
+ if (ret) {
+ dev_err(&client->dev, "%s failed to write regs\n", __func__);
+ goto err_rpm_put;
+ }
+
+ fmt = v4l2_subdev_state_get_format(state, 0);
+ gc2145_format = gc2145_get_format_code(gc2145, fmt->code);
+
+ /* Set the output format */
+ cci_write(gc2145->regmap, GC2145_REG_PAGE_SELECT, 0x00, &ret);
+
+ cci_write(gc2145->regmap, GC2145_REG_OUTPUT_FMT,
+ gc2145_format->output_fmt, &ret);
+ cci_update_bits(gc2145->regmap, GC2145_REG_BYPASS_MODE,
+ GC2145_BYPASS_MODE_SWITCH,
+ gc2145_format->switch_bit ? GC2145_BYPASS_MODE_SWITCH
+ : 0, &ret);
+ if (ret) {
+ dev_err(&client->dev, "%s failed to write regs\n", __func__);
+ goto err_rpm_put;
+ }
+
+ /* Apply customized values from user */
+ ret = __v4l2_ctrl_handler_setup(&gc2145->ctrls.handler);
+ if (ret) {
+ dev_err(&client->dev, "%s failed to apply ctrls\n", __func__);
+ goto err_rpm_put;
+ }
+
+ /* Perform MIPI specific configuration */
+ ret = gc2145_config_mipi_mode(gc2145, gc2145_format);
+ if (ret) {
+ dev_err(&client->dev, "%s failed to write mipi conf\n",
+ __func__);
+ goto err_rpm_put;
+ }
+
+ cci_write(gc2145->regmap, GC2145_REG_PAGE_SELECT, 0x00, &ret);
+
+ return 0;
+
+err_rpm_put:
+ pm_runtime_mark_last_busy(&client->dev);
+ pm_runtime_put_autosuspend(&client->dev);
+ return ret;
+}
+
+static void gc2145_stop_streaming(struct gc2145 *gc2145)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&gc2145->sd);
+ int ret = 0;
+
+ /* Disable lanes & mipi streaming */
+ cci_write(gc2145->regmap, GC2145_REG_PAGE_SELECT, 0x03, &ret);
+ cci_update_bits(gc2145->regmap, GC2145_REG_BUF_CSI2_MODE,
+ GC2145_CSI2_MODE_EN | GC2145_CSI2_MODE_MIPI_EN, 0,
+ &ret);
+ cci_write(gc2145->regmap, GC2145_REG_PAGE_SELECT, 0x00, &ret);
+ if (ret)
+ dev_err(&client->dev, "%s failed to write regs\n", __func__);
+
+ pm_runtime_mark_last_busy(&client->dev);
+ pm_runtime_put_autosuspend(&client->dev);
+}
+
+static int gc2145_set_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct gc2145 *gc2145 = to_gc2145(sd);
+ struct v4l2_subdev_state *state;
+ int ret = 0;
+
+ state = v4l2_subdev_lock_and_get_active_state(sd);
+
+ if (enable)
+ ret = gc2145_start_streaming(gc2145, state);
+ else
+ gc2145_stop_streaming(gc2145);
+
+ v4l2_subdev_unlock_state(state);
+
+ return ret;
+}
+
+/* Power/clock management functions */
+static int gc2145_power_on(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct gc2145 *gc2145 = to_gc2145(sd);
+ int ret;
+
+ ret = regulator_bulk_enable(GC2145_NUM_SUPPLIES, gc2145->supplies);
+ if (ret) {
+ dev_err(dev, "failed to enable regulators\n");
+ return ret;
+ }
+
+ ret = clk_prepare_enable(gc2145->xclk);
+ if (ret) {
+ dev_err(dev, "failed to enable clock\n");
+ goto reg_off;
+ }
+
+ gpiod_set_value_cansleep(gc2145->powerdown_gpio, 0);
+ gpiod_set_value_cansleep(gc2145->reset_gpio, 0);
+
+ /*
+ * Datasheet doesn't mention timing between PWDN/RESETB control and
+ * i2c access however, experimentation shows that a rather big delay is
+ * needed.
+ */
+ msleep(41);
+
+ return 0;
+
+reg_off:
+ regulator_bulk_disable(GC2145_NUM_SUPPLIES, gc2145->supplies);
+
+ return ret;
+}
+
+static int gc2145_power_off(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct gc2145 *gc2145 = to_gc2145(sd);
+
+ gpiod_set_value_cansleep(gc2145->powerdown_gpio, 1);
+ gpiod_set_value_cansleep(gc2145->reset_gpio, 1);
+ clk_disable_unprepare(gc2145->xclk);
+ regulator_bulk_disable(GC2145_NUM_SUPPLIES, gc2145->supplies);
+
+ return 0;
+}
+
+static int gc2145_get_regulators(struct gc2145 *gc2145)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&gc2145->sd);
+ unsigned int i;
+
+ for (i = 0; i < GC2145_NUM_SUPPLIES; i++)
+ gc2145->supplies[i].supply = gc2145_supply_name[i];
+
+ return devm_regulator_bulk_get(&client->dev, GC2145_NUM_SUPPLIES,
+ gc2145->supplies);
+}
+
+/* Verify chip ID */
+static int gc2145_identify_module(struct gc2145 *gc2145)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&gc2145->sd);
+ int ret;
+ u64 chip_id;
+
+ ret = cci_read(gc2145->regmap, GC2145_REG_CHIP_ID, &chip_id, NULL);
+ if (ret) {
+ dev_err(&client->dev, "failed to read chip id (%d)\n", ret);
+ return ret;
+ }
+
+ if (chip_id != GC2145_CHIP_ID) {
+ dev_err(&client->dev, "chip id mismatch: %x!=%llx\n",
+ GC2145_CHIP_ID, chip_id);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static const char * const test_pattern_menu[] = {
+ "Disabled",
+ "Colored patterns",
+ "Uniform white",
+ "Uniform yellow",
+ "Uniform cyan",
+ "Uniform green",
+ "Uniform magenta",
+ "Uniform red",
+ "Uniform black",
+};
+
+#define GC2145_TEST_PATTERN_ENABLE BIT(0)
+#define GC2145_TEST_PATTERN_UXGA BIT(3)
+
+#define GC2145_TEST_UNIFORM BIT(3)
+#define GC2145_TEST_WHITE (4 << 4)
+#define GC2145_TEST_YELLOW (8 << 4)
+#define GC2145_TEST_CYAN (9 << 4)
+#define GC2145_TEST_GREEN (6 << 4)
+#define GC2145_TEST_MAGENTA (10 << 4)
+#define GC2145_TEST_RED (5 << 4)
+#define GC2145_TEST_BLACK (0)
+
+static const u8 test_pattern_val[] = {
+ 0,
+ GC2145_TEST_PATTERN_ENABLE,
+ GC2145_TEST_UNIFORM | GC2145_TEST_WHITE,
+ GC2145_TEST_UNIFORM | GC2145_TEST_YELLOW,
+ GC2145_TEST_UNIFORM | GC2145_TEST_CYAN,
+ GC2145_TEST_UNIFORM | GC2145_TEST_GREEN,
+ GC2145_TEST_UNIFORM | GC2145_TEST_MAGENTA,
+ GC2145_TEST_UNIFORM | GC2145_TEST_RED,
+ GC2145_TEST_UNIFORM | GC2145_TEST_BLACK,
+};
+
+static const struct v4l2_subdev_core_ops gc2145_core_ops = {
+ .subscribe_event = v4l2_ctrl_subdev_subscribe_event,
+ .unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+static const struct v4l2_subdev_video_ops gc2145_video_ops = {
+ .s_stream = gc2145_set_stream,
+};
+
+static const struct v4l2_subdev_pad_ops gc2145_pad_ops = {
+ .init_cfg = gc2145_init_cfg,
+ .enum_mbus_code = gc2145_enum_mbus_code,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .set_fmt = gc2145_set_pad_format,
+ .get_selection = gc2145_get_selection,
+ .enum_frame_size = gc2145_enum_frame_size,
+};
+
+static const struct v4l2_subdev_ops gc2145_subdev_ops = {
+ .core = &gc2145_core_ops,
+ .video = &gc2145_video_ops,
+ .pad = &gc2145_pad_ops,
+};
+
+static int gc2145_set_ctrl_test_pattern(struct gc2145 *gc2145, int value)
+{
+ int ret = 0;
+
+ if (!value) {
+ /* Disable test pattern */
+ cci_write(gc2145->regmap, GC2145_REG_DEBUG_MODE2, 0, &ret);
+ return cci_write(gc2145->regmap, GC2145_REG_DEBUG_MODE3, 0,
+ &ret);
+ }
+
+ /* Enable test pattern, colored or uniform */
+ cci_write(gc2145->regmap, GC2145_REG_DEBUG_MODE2,
+ GC2145_TEST_PATTERN_ENABLE | GC2145_TEST_PATTERN_UXGA, &ret);
+
+ if (!(test_pattern_val[value] & GC2145_TEST_UNIFORM))
+ return cci_write(gc2145->regmap, GC2145_REG_DEBUG_MODE3, 0,
+ &ret);
+
+ /* Uniform */
+ return cci_write(gc2145->regmap, GC2145_REG_DEBUG_MODE3,
+ test_pattern_val[value], &ret);
+}
+
+static int gc2145_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct v4l2_subdev *sd = gc2145_ctrl_to_sd(ctrl);
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+ struct gc2145 *gc2145 = to_gc2145(sd);
+ int ret;
+
+ if (pm_runtime_get_if_in_use(&client->dev) == 0)
+ return 0;
+
+ switch (ctrl->id) {
+ case V4L2_CID_HBLANK:
+ ret = cci_write(gc2145->regmap, GC2145_REG_HBLANK, ctrl->val,
+ NULL);
+ break;
+ case V4L2_CID_VBLANK:
+ ret = cci_write(gc2145->regmap, GC2145_REG_VBLANK, ctrl->val,
+ NULL);
+ break;
+ case V4L2_CID_TEST_PATTERN:
+ ret = gc2145_set_ctrl_test_pattern(gc2145, ctrl->val);
+ break;
+ case V4L2_CID_HFLIP:
+ ret = cci_update_bits(gc2145->regmap, GC2145_REG_ANALOG_MODE1,
+ BIT(0), (ctrl->val ? BIT(0) : 0), NULL);
+ break;
+ case V4L2_CID_VFLIP:
+ ret = cci_update_bits(gc2145->regmap, GC2145_REG_ANALOG_MODE1,
+ BIT(1), (ctrl->val ? BIT(1) : 0), NULL);
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ pm_runtime_mark_last_busy(&client->dev);
+ pm_runtime_put_autosuspend(&client->dev);
+
+ return ret;
+}
+
+static const struct v4l2_ctrl_ops gc2145_ctrl_ops = {
+ .s_ctrl = gc2145_s_ctrl,
+};
+
+/* Initialize control handlers */
+static int gc2145_init_controls(struct gc2145 *gc2145)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&gc2145->sd);
+ const struct v4l2_ctrl_ops *ops = &gc2145_ctrl_ops;
+ struct gc2145_ctrls *ctrls = &gc2145->ctrls;
+ struct v4l2_ctrl_handler *hdl = &ctrls->handler;
+ struct v4l2_fwnode_device_properties props;
+ int ret;
+
+ ret = v4l2_ctrl_handler_init(hdl, 12);
+ if (ret)
+ return ret;
+
+ ctrls->pixel_rate = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_PIXEL_RATE,
+ GC2145_640_480_PIXELRATE,
+ GC2145_1600_1200_PIXELRATE, 1,
+ supported_modes[0].pixel_rate);
+
+ ctrls->link_freq = v4l2_ctrl_new_int_menu(hdl, ops, V4L2_CID_LINK_FREQ,
+ ARRAY_SIZE(gc2145_link_freq_menu) - 1,
+ 0, gc2145_link_freq_menu);
+ if (ctrls->link_freq)
+ ctrls->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ ctrls->hblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HBLANK,
+ 0, 0xfff, 1, GC2145_640_480_HBLANK);
+
+ ctrls->vblank = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VBLANK,
+ 0, 0x1fff, 1, GC2145_640_480_VBLANK);
+
+ ctrls->test_pattern =
+ v4l2_ctrl_new_std_menu_items(hdl, ops, V4L2_CID_TEST_PATTERN,
+ ARRAY_SIZE(test_pattern_menu) - 1,
+ 0, 0, test_pattern_menu);
+ ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP,
+ 0, 1, 1, 0);
+ ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP,
+ 0, 1, 1, 0);
+
+ if (hdl->error) {
+ ret = hdl->error;
+ dev_err(&client->dev, "control init failed (%d)\n", ret);
+ goto error;
+ }
+
+ ret = v4l2_fwnode_device_parse(&client->dev, &props);
+ if (ret)
+ goto error;
+
+ ret = v4l2_ctrl_new_fwnode_properties(hdl, &gc2145_ctrl_ops,
+ &props);
+ if (ret)
+ goto error;
+
+ gc2145->sd.ctrl_handler = hdl;
+
+ return 0;
+
+error:
+ v4l2_ctrl_handler_free(hdl);
+
+ return ret;
+}
+
+static int gc2145_check_hwcfg(struct device *dev)
+{
+ struct fwnode_handle *endpoint;
+ struct v4l2_fwnode_endpoint ep_cfg = {
+ .bus_type = V4L2_MBUS_CSI2_DPHY
+ };
+ int ret;
+
+ endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(dev), NULL);
+ if (!endpoint) {
+ dev_err(dev, "endpoint node not found\n");
+ return -EINVAL;
+ }
+
+ ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &ep_cfg);
+ fwnode_handle_put(endpoint);
+ if (ret)
+ return ret;
+
+ /* Check the number of MIPI CSI2 data lanes */
+ if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2) {
+ dev_err(dev, "only 2 data lanes are currently supported\n");
+ ret = -EINVAL;
+ goto out;
+ }
+
+ /* Check the link frequency set in device tree */
+ if (!ep_cfg.nr_of_link_frequencies) {
+ dev_err(dev, "link-frequency property not found in DT\n");
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (ep_cfg.nr_of_link_frequencies != 3 ||
+ ep_cfg.link_frequencies[0] != GC2145_640_480_LINKFREQ ||
+ ep_cfg.link_frequencies[1] != GC2145_1280_720_LINKFREQ ||
+ ep_cfg.link_frequencies[2] != GC2145_1600_1200_LINKFREQ) {
+ dev_err(dev, "Invalid link-frequencies provided\n");
+ ret = -EINVAL;
+ }
+
+out:
+ v4l2_fwnode_endpoint_free(&ep_cfg);
+
+ return ret;
+}
+
+static int gc2145_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ unsigned int xclk_freq;
+ struct gc2145 *gc2145;
+ int ret;
+
+ gc2145 = devm_kzalloc(&client->dev, sizeof(*gc2145), GFP_KERNEL);
+ if (!gc2145)
+ return -ENOMEM;
+
+ v4l2_i2c_subdev_init(&gc2145->sd, client, &gc2145_subdev_ops);
+
+ /* Check the hardware configuration in device tree */
+ if (gc2145_check_hwcfg(dev))
+ return -EINVAL;
+
+ /* Get system clock (xclk) */
+ gc2145->xclk = devm_clk_get(dev, NULL);
+ if (IS_ERR(gc2145->xclk))
+ return dev_err_probe(dev, PTR_ERR(gc2145->xclk),
+ "failed to get xclk\n");
+
+ xclk_freq = clk_get_rate(gc2145->xclk);
+ if (xclk_freq != GC2145_XCLK_FREQ) {
+ dev_err(dev, "xclk frequency not supported: %d Hz\n",
+ xclk_freq);
+ return -EINVAL;
+ }
+
+ ret = gc2145_get_regulators(gc2145);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "failed to get regulators\n");
+
+ /* Request optional reset pin */
+ gc2145->reset_gpio = devm_gpiod_get_optional(dev, "reset",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(gc2145->reset_gpio))
+ return dev_err_probe(dev, PTR_ERR(gc2145->reset_gpio),
+ "failed to get reset_gpio\n");
+
+ /* Request optional powerdown pin */
+ gc2145->powerdown_gpio = devm_gpiod_get_optional(dev, "powerdown",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(gc2145->powerdown_gpio))
+ return dev_err_probe(dev, PTR_ERR(gc2145->powerdown_gpio),
+ "failed to get powerdown_gpio\n");
+
+ /* Initialise the regmap for further cci access */
+ gc2145->regmap = devm_cci_regmap_init_i2c(client, 8);
+ if (IS_ERR(gc2145->regmap))
+ return dev_err_probe(dev, PTR_ERR(gc2145->regmap),
+ "failed to get cci regmap\n");
+
+ /*
+ * The sensor must be powered for gc2145_identify_module()
+ * to be able to read the CHIP_ID register
+ */
+ ret = gc2145_power_on(dev);
+ if (ret)
+ return ret;
+
+ ret = gc2145_identify_module(gc2145);
+ if (ret)
+ goto error_power_off;
+
+ /* Set default mode */
+ gc2145->mode = &supported_modes[0];
+
+ ret = gc2145_init_controls(gc2145);
+ if (ret)
+ goto error_power_off;
+
+ /* Initialize subdev */
+ gc2145->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE |
+ V4L2_SUBDEV_FL_HAS_EVENTS;
+ gc2145->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+
+ /* Initialize source pad */
+ gc2145->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+ ret = media_entity_pads_init(&gc2145->sd.entity, 1, &gc2145->pad);
+ if (ret) {
+ dev_err(dev, "failed to init entity pads: %d\n", ret);
+ goto error_handler_free;
+ }
+
+ gc2145->sd.state_lock = gc2145->ctrls.handler.lock;
+ ret = v4l2_subdev_init_finalize(&gc2145->sd);
+ if (ret < 0) {
+ dev_err(dev, "subdev init error: %d\n", ret);
+ goto error_media_entity;
+ }
+
+ /* Enable runtime PM and turn off the device */
+ pm_runtime_set_active(dev);
+ pm_runtime_get_noresume(&client->dev);
+ pm_runtime_enable(dev);
+
+ pm_runtime_set_autosuspend_delay(&client->dev, 1000);
+ pm_runtime_use_autosuspend(&client->dev);
+ pm_runtime_put_autosuspend(&client->dev);
+
+ ret = v4l2_async_register_subdev_sensor(&gc2145->sd);
+ if (ret < 0) {
+ dev_err(dev, "failed to register sensor sub-device: %d\n", ret);
+ goto error_subdev_cleanup;
+ }
+
+ return 0;
+
+error_subdev_cleanup:
+ v4l2_subdev_cleanup(&gc2145->sd);
+ pm_runtime_disable(&client->dev);
+ pm_runtime_set_suspended(&client->dev);
+
+error_media_entity:
+ media_entity_cleanup(&gc2145->sd.entity);
+
+error_handler_free:
+ v4l2_ctrl_handler_free(&gc2145->ctrls.handler);
+
+error_power_off:
+ gc2145_power_off(dev);
+
+ return ret;
+}
+
+static void gc2145_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct gc2145 *gc2145 = to_gc2145(sd);
+
+ v4l2_subdev_cleanup(sd);
+ v4l2_async_unregister_subdev(sd);
+ media_entity_cleanup(&sd->entity);
+ v4l2_ctrl_handler_free(&gc2145->ctrls.handler);
+
+ pm_runtime_disable(&client->dev);
+ if (!pm_runtime_status_suspended(&client->dev))
+ gc2145_power_off(&client->dev);
+ pm_runtime_set_suspended(&client->dev);
+}
+
+static const struct of_device_id gc2145_dt_ids[] = {
+ { .compatible = "galaxycore,gc2145" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, gc2145_dt_ids);
+
+static const struct dev_pm_ops gc2145_pm_ops = {
+ RUNTIME_PM_OPS(gc2145_power_off, gc2145_power_on, NULL)
+};
+
+static struct i2c_driver gc2145_i2c_driver = {
+ .driver = {
+ .name = "gc2145",
+ .of_match_table = gc2145_dt_ids,
+ .pm = pm_ptr(&gc2145_pm_ops),
+ },
+ .probe = gc2145_probe,
+ .remove = gc2145_remove,
+};
+
+module_i2c_driver(gc2145_i2c_driver);
+
+MODULE_AUTHOR("Alain Volmat <[email protected]>");
+MODULE_DESCRIPTION("GalaxyCore GC2145 sensor driver");
+MODULE_LICENSE("GPL");
--
2.25.1
Hi Alain,
kernel test robot noticed the following build errors:
[auto build test ERROR on linuxtv-media-stage/master]
[also build test ERROR on linus/master v6.7-rc2 next-20231122]
[cannot apply to media-tree/master robh/for-next]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Alain-Volmat/dt-bindings-vendor-prefixes-Add-prefix-for-GalaxyCore-Inc/20231122-155443
base: https://git.linuxtv.org/media_stage.git master
patch link: https://lore.kernel.org/r/20231122075154.789431-4-alain.volmat%40foss.st.com
patch subject: [PATCH v5 3/3] media: i2c: gc2145: Galaxy Core GC2145 sensor support
config: alpha-allyesconfig (https://download.01.org/0day-ci/archive/20231123/[email protected]/config)
compiler: alpha-linux-gcc (GCC) 13.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20231123/[email protected]/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
All errors (new ones prefixed by >>):
drivers/media/i2c/gc2145.c: In function 'gc2145_init_cfg':
>> drivers/media/i2c/gc2145.c:664:18: error: implicit declaration of function 'v4l2_subdev_state_get_format'; did you mean 'v4l2_subdev_state_get_stream_format'? [-Werror=implicit-function-declaration]
664 | format = v4l2_subdev_state_get_format(state, 0);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
| v4l2_subdev_state_get_stream_format
drivers/media/i2c/gc2145.c:664:16: warning: assignment to 'struct v4l2_mbus_framefmt *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
664 | format = v4l2_subdev_state_get_format(state, 0);
| ^
>> drivers/media/i2c/gc2145.c:669:16: error: implicit declaration of function 'v4l2_subdev_state_get_crop'; did you mean 'v4l2_subdev_state_get_stream_crop'? [-Werror=implicit-function-declaration]
669 | crop = v4l2_subdev_state_get_crop(state, 0);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| v4l2_subdev_state_get_stream_crop
drivers/media/i2c/gc2145.c:669:14: warning: assignment to 'struct v4l2_rect *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
669 | crop = v4l2_subdev_state_get_crop(state, 0);
| ^
drivers/media/i2c/gc2145.c: In function 'gc2145_get_selection':
drivers/media/i2c/gc2145.c:681:26: error: invalid type argument of unary '*' (have 'int')
681 | sel->r = *v4l2_subdev_state_get_crop(sd_state, 0);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/gc2145.c: In function 'gc2145_set_pad_format':
drivers/media/i2c/gc2145.c:758:18: warning: assignment to 'struct v4l2_mbus_framefmt *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
758 | framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
| ^
drivers/media/i2c/gc2145.c:770:14: warning: assignment to 'struct v4l2_rect *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
770 | crop = v4l2_subdev_state_get_crop(sd_state, fmt->pad);
| ^
drivers/media/i2c/gc2145.c: In function 'gc2145_start_streaming':
drivers/media/i2c/gc2145.c:874:13: warning: assignment to 'struct v4l2_mbus_framefmt *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
874 | fmt = v4l2_subdev_state_get_format(state, 0);
| ^
cc1: some warnings being treated as errors
vim +664 drivers/media/i2c/gc2145.c
655
656 static int gc2145_init_cfg(struct v4l2_subdev *sd,
657 struct v4l2_subdev_state *state)
658 {
659 struct gc2145 *gc2145 = to_gc2145(sd);
660 struct v4l2_mbus_framefmt *format;
661 struct v4l2_rect *crop;
662
663 /* Initialize pad format */
> 664 format = v4l2_subdev_state_get_format(state, 0);
665 gc2145_update_pad_format(gc2145, &supported_modes[0], format,
666 MEDIA_BUS_FMT_RGB565_1X16);
667
668 /* Initialize crop rectangle. */
> 669 crop = v4l2_subdev_state_get_crop(state, 0);
670 *crop = supported_modes[0].crop;
671
672 return 0;
673 }
674
--
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
Hi Alain,
kernel test robot noticed the following build errors:
[auto build test ERROR on linuxtv-media-stage/master]
[also build test ERROR on linus/master v6.7-rc2 next-20231122]
[cannot apply to media-tree/master robh/for-next]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Alain-Volmat/dt-bindings-vendor-prefixes-Add-prefix-for-GalaxyCore-Inc/20231122-155443
base: https://git.linuxtv.org/media_stage.git master
patch link: https://lore.kernel.org/r/20231122075154.789431-4-alain.volmat%40foss.st.com
patch subject: [PATCH v5 3/3] media: i2c: gc2145: Galaxy Core GC2145 sensor support
config: x86_64-allyesconfig (https://download.01.org/0day-ci/archive/20231123/[email protected]/config)
compiler: clang version 16.0.4 (https://github.com/llvm/llvm-project.git ae42196bc493ffe877a7e3dff8be32035dea4d07)
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20231123/[email protected]/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
All errors (new ones prefixed by >>):
>> drivers/media/i2c/gc2145.c:664:11: error: call to undeclared function 'v4l2_subdev_state_get_format'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
format = v4l2_subdev_state_get_format(state, 0);
^
drivers/media/i2c/gc2145.c:664:9: error: incompatible integer to pointer conversion assigning to 'struct v4l2_mbus_framefmt *' from 'int' [-Wint-conversion]
format = v4l2_subdev_state_get_format(state, 0);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/media/i2c/gc2145.c:669:9: error: call to undeclared function 'v4l2_subdev_state_get_crop'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
crop = v4l2_subdev_state_get_crop(state, 0);
^
drivers/media/i2c/gc2145.c:669:7: error: incompatible integer to pointer conversion assigning to 'struct v4l2_rect *' from 'int' [-Wint-conversion]
crop = v4l2_subdev_state_get_crop(state, 0);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/gc2145.c:681:13: error: call to undeclared function 'v4l2_subdev_state_get_crop'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
sel->r = *v4l2_subdev_state_get_crop(sd_state, 0);
^
drivers/media/i2c/gc2145.c:681:12: error: indirection requires pointer operand ('int' invalid)
sel->r = *v4l2_subdev_state_get_crop(sd_state, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/gc2145.c:758:13: error: call to undeclared function 'v4l2_subdev_state_get_format'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
^
drivers/media/i2c/gc2145.c:758:11: error: incompatible integer to pointer conversion assigning to 'struct v4l2_mbus_framefmt *' from 'int' [-Wint-conversion]
framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/gc2145.c:770:9: error: call to undeclared function 'v4l2_subdev_state_get_crop'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
crop = v4l2_subdev_state_get_crop(sd_state, fmt->pad);
^
drivers/media/i2c/gc2145.c:770:7: error: incompatible integer to pointer conversion assigning to 'struct v4l2_rect *' from 'int' [-Wint-conversion]
crop = v4l2_subdev_state_get_crop(sd_state, fmt->pad);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/gc2145.c:874:8: error: call to undeclared function 'v4l2_subdev_state_get_format'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
fmt = v4l2_subdev_state_get_format(state, 0);
^
drivers/media/i2c/gc2145.c:874:6: error: incompatible integer to pointer conversion assigning to 'struct v4l2_mbus_framefmt *' from 'int' [-Wint-conversion]
fmt = v4l2_subdev_state_get_format(state, 0);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
12 errors generated.
vim +/v4l2_subdev_state_get_format +664 drivers/media/i2c/gc2145.c
655
656 static int gc2145_init_cfg(struct v4l2_subdev *sd,
657 struct v4l2_subdev_state *state)
658 {
659 struct gc2145 *gc2145 = to_gc2145(sd);
660 struct v4l2_mbus_framefmt *format;
661 struct v4l2_rect *crop;
662
663 /* Initialize pad format */
> 664 format = v4l2_subdev_state_get_format(state, 0);
665 gc2145_update_pad_format(gc2145, &supported_modes[0], format,
666 MEDIA_BUS_FMT_RGB565_1X16);
667
668 /* Initialize crop rectangle. */
> 669 crop = v4l2_subdev_state_get_crop(state, 0);
670 *crop = supported_modes[0].crop;
671
672 return 0;
673 }
674
--
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
On Wed 2023-11-22 08:51:48, Alain Volmat wrote:
> Introduction of the Galaxy Core GC2145 XVGA CMOS camera sensor.
>
> Signed-off-by: Alain Volmat <[email protected]>
> Reviewed-by: Conor Dooley <[email protected]>
Reviewed-by: Pavel Machek <[email protected]>
BR,
Pavel
--
People of Russia, stop Putin before his war on Ukraine escalates.
Hi!
> Addition of support for the Galaxy Core GC2145 XVGA sensor.
> The sensor supports both DVP and CSI-2 interfaces however for
> the time being only CSI-2 is implemented.
>
> Configurations are currently based on initialization scripts
> coming from Galaxy Core and so for that purpose only 3 static
> resolutions are supported:
> - 640x480
> - 1280x720
> - 1600x1200
Also only limited subset of pixel formats is implemented? Would be
worth mentioning in the changelog, but perhaps comment at the start of
the file would be even better.
> +++ b/drivers/media/i2c/Kconfig
> @@ -50,6 +50,16 @@ config VIDEO_AR0521
> To compile this driver as a module, choose M here: the
> module will be called ar0521.
>
> +config VIDEO_GC2145
> + select V4L2_CCI_I2C
> + tristate "GalaxyCore GC2145 sensor support"
> + help
> + This is a V4L2 sensor-level driver for GalaxyCore GC2145
> + 2 Mpixel camera.
Normally tristate would go before select.
Reviewed-by: Pavel Machek <[email protected]>
(But you probably want to solve the problems reported by the build
bot).
Thanks and best regards,
Pavel
--
People of Russia, stop Putin before his war on Ukraine escalates.