From: Sebastian Reichel <[email protected]>
Hi,
This adds adds support for the UNI-T UTi260B thermal camera, which is based
on i.MX6ULL. Patches 1-14 clean up all warnings reported by CHECK_DTBS for
i.MX6ULL (i.e. for an empty board). They are not specific to the UTi260B and
in fact that machine has most of the IP handled by these patches marked as
disabled. Then patches 15+16 introduce the vendor and board compatible DT
bindings. Finally the last patches adds support for the thermal camera itself.
The DT is based on reverse engineered information. More information about
the device can be found in this presentation from Embedded Recipes 2023:
* https://embedded-recipes.org/2023/wp-content/uploads/2023/10/Running-FOSS-on-a-Thermal-Camera-Sebastian-Reichel-compressed.pdf
* https://www.youtube.com/watch?v=uvObsCG-Cqo
I also prepared a branch with these patches (and a minimal kernel config)
and published it here:
https://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-misc.git/log/?h=uti260b-v4
Changes since PATCHv3:
* https://lore.kernel.org/all/[email protected]/
- weim binding: use " instead of '
- weim binding: use "if: not: required: - foo" instead of "if: properties: foo: false"
- imx6ull-uti260b.dts: merge ecspi3_csgrp into ecspi3grp
- collect Reviewed-by from Krzysztof Kozlowski
Changes since PATCHv2:
* https://lore.kernel.org/all/[email protected]/
- drop fsl,imx-asrc YAML binding conversion (merged)
- collect a bunch of Reviewed-by/Acked-by tags
- weim DT binding: fix issue with requirements
- xnur-gpio -> xnur-gpios change: Improve patch long description
Changes since PATCHv1:
* https://lore.kernel.org/all/[email protected]/
- uni-t,imx6ull-uti260b -> uni-t,uti260b
- add Acked-by for uni-t vendor prefix
- add Acked-by for HDMI audio index fix
- add Acked-by for LCDIF power-domain requirement drop
- anatop DT binding: Fixed indentation in example
- anatop DT binding: Described IRQs
- touchscreen DT binding: change tsc@ to touchscreen@ in example
- touchscreen DT binding: change xnur-gpio to xnur-gpios
- weim DT binding: drop acme,whatever example
- weim DT binding: use flash@ instead of nor@
- weim DT binding: update weim.txt reference in arcx,anybus-controller.txt
- weim DT binding: switch to memory-controller binding
- fsl,imx-asrc DT binding: fix ASoC patch subject prefix
- fsl,imx-asrc DT binding: add constraints
- add new patch fixing xnur-gpio(s) in all i.MX6UL board DT files
- add new patch fixing touchscreen nodename in i.MX6UL SoC DT file
- add new patch fixing weim nodename in all i.MX SoC DT files
- device DTS: use color/functions for the led
- device DTS: increase SPI speed
- device DTS: add comment for SD / eMMC node
Unadressed feedback from PATCHv1:
- anatop phandle vs parent: technically it makes sense to just use the
parent, but this driver is only used by i.MX6. The current code makes
use of the phandle, so we cannot drop it because of backwards
compatibility. So I don't see a point in deprecating this property.
- touchscreen binding: I kept measure-delay-time and pre-charge-time
values in hex, since that is being used everywhere and the unit
is unknown. The values are directly written into HW registers and
the i.MX6UL TRM does not provide any hints about the unit. I do not
have an i.MX6UL device with a touchsreen, so I cannot test either.
- regulator name in DT: I did not rename the regulators to just
"regulator", since the nodename must be unique.
Greetings,
-- Sebastian
Sebastian Reichel (16):
dt-bindings: pinctrl: fsl,imx6ul-pinctrl: convert to YAML
dt-bindings: bus: imx-weim: convert to YAML
dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML
dt-bindings: soc: imx: fsl,imx-anatop: add binding
dt-bindings: soc: imx: fsl,imx-iomuxc-gpr: add imx6
dt-bindings: lcdif: Do not require power-domains for i.MX6ULL
dt-bindings: fsl-imx-sdma: fix HDMI audio index
ARM: dts: imx6ull: fix pinctrl node name
ARM: dts: imx6ul: Remove fsl,anatop from usbotg1
ARM: dts: imx6ul: add missing #thermal-sensor-cells
ARM: dts: nxp: imx6ul: xnur-gpio -> xnur-gpios
ARM: dts: nxp: imx6ul: fix touchscreen node name
ARM: dts: nxp: imx: fix weim node name
dt-bindings: vendor-prefixes: add UNI-T
dt-bindings: arm: add UNI-T UTi260B
ARM: dts: imx6ull-uti260b: Add board
.../devicetree/bindings/arm/fsl.yaml | 1 +
.../devicetree/bindings/bus/imx-weim.txt | 117 ----
.../bindings/display/fsl,lcdif.yaml | 8 +-
.../devicetree/bindings/dma/fsl,imx-sdma.yaml | 3 +-
.../input/touchscreen/fsl,imx6ul-tsc.yaml | 97 +++
.../bindings/input/touchscreen/imx6ul_tsc.txt | 38 --
.../fsl/fsl,imx-weim-peripherals.yaml | 31 +
.../memory-controllers/fsl/fsl,imx-weim.yaml | 204 +++++++
.../mc-peripheral-props.yaml | 1 +
.../bindings/pinctrl/fsl,imx6ul-pinctrl.txt | 37 --
.../bindings/pinctrl/fsl,imx6ul-pinctrl.yaml | 116 ++++
.../bindings/soc/imx/fsl,imx-anatop.yaml | 128 ++++
.../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml | 18 +-
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
arch/arm/boot/dts/nxp/imx/imx1.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx27.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx31.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx35.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx51.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6sl.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6sx.dtsi | 2 +-
.../boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts | 2 +-
.../nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 6 +-
.../boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts | 567 ++++++++++++++++++
arch/arm/boot/dts/nxp/imx/imx6ull.dtsi | 2 +-
.../fieldbus/arcx,anybus-controller.txt | 2 +-
31 files changed, 1191 insertions(+), 212 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
delete mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/soc/imx/fsl,imx-anatop.yaml
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
--
2.43.0
Convert the i.MX Wireless External Interface Module binding to YAML.
Signed-off-by: Sebastian Reichel <[email protected]>
---
.../devicetree/bindings/bus/imx-weim.txt | 117 ----------
.../fsl/fsl,imx-weim-peripherals.yaml | 31 +++
.../memory-controllers/fsl/fsl,imx-weim.yaml | 204 ++++++++++++++++++
.../mc-peripheral-props.yaml | 1 +
.../fieldbus/arcx,anybus-controller.txt | 2 +-
5 files changed, 237 insertions(+), 118 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt
deleted file mode 100644
index e7f502070d77..000000000000
--- a/Documentation/devicetree/bindings/bus/imx-weim.txt
+++ /dev/null
@@ -1,117 +0,0 @@
-Device tree bindings for i.MX Wireless External Interface Module (WEIM)
-
-The term "wireless" does not imply that the WEIM is literally an interface
-without wires. It simply means that this module was originally designed for
-wireless and mobile applications that use low-power technology.
-
-The actual devices are instantiated from the child nodes of a WEIM node.
-
-Required properties:
-
- - compatible: Should contain one of the following:
- "fsl,imx1-weim"
- "fsl,imx27-weim"
- "fsl,imx51-weim"
- "fsl,imx50-weim"
- "fsl,imx6q-weim"
- - reg: A resource specifier for the register space
- (see the example below)
- - clocks: the clock, see the example below.
- - #address-cells: Must be set to 2 to allow memory address translation
- - #size-cells: Must be set to 1 to allow CS address passing
- - ranges: Must be set up to reflect the memory layout with four
- integer values for each chip-select line in use:
-
- <cs-number> 0 <physical address of mapping> <size>
-
-Optional properties:
-
- - fsl,weim-cs-gpr: For "fsl,imx50-weim" and "fsl,imx6q-weim" type of
- devices, it should be the phandle to the system General
- Purpose Register controller that contains WEIM CS GPR
- register, e.g. IOMUXC_GPR1 on i.MX6Q. IOMUXC_GPR1[11:0]
- should be set up as one of the following 4 possible
- values depending on the CS space configuration.
-
- IOMUXC_GPR1[11:0] CS0 CS1 CS2 CS3
- ---------------------------------------------
- 05 128M 0M 0M 0M
- 033 64M 64M 0M 0M
- 0113 64M 32M 32M 0M
- 01111 32M 32M 32M 32M
-
- In case that the property is absent, the reset value or
- what bootloader sets up in IOMUXC_GPR1[11:0] will be
- used.
-
- - fsl,burst-clk-enable For "fsl,imx50-weim" and "fsl,imx6q-weim" type of
- devices, the presence of this property indicates that
- the weim bus should operate in Burst Clock Mode.
-
- - fsl,continuous-burst-clk Make Burst Clock to output continuous clock.
- Without this option Burst Clock will output clock
- only when necessary. This takes effect only if
- "fsl,burst-clk-enable" is set.
-
-Timing property for child nodes. It is mandatory, not optional.
-
- - fsl,weim-cs-timing: The timing array, contains timing values for the
- child node. We get the CS indexes from the address
- ranges in the child node's "reg" property.
- The number of registers depends on the selected chip:
- For i.MX1, i.MX21 ("fsl,imx1-weim") there are two
- registers: CSxU, CSxL.
- For i.MX25, i.MX27, i.MX31 and i.MX35 ("fsl,imx27-weim")
- there are three registers: CSCRxU, CSCRxL, CSCRxA.
- For i.MX50, i.MX53 ("fsl,imx50-weim"),
- i.MX51 ("fsl,imx51-weim") and i.MX6Q ("fsl,imx6q-weim")
- there are six registers: CSxGCR1, CSxGCR2, CSxRCR1,
- CSxRCR2, CSxWCR1, CSxWCR2.
-
-Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
-
- weim: weim@21b8000 {
- compatible = "fsl,imx6q-weim";
- reg = <0x021b8000 0x4000>;
- clocks = <&clks 196>;
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0x08000000 0x08000000>;
- fsl,weim-cs-gpr = <&gpr>;
-
- nor@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x02000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- bank-width = <2>;
- fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
- 0x0000c000 0x1404a38e 0x00000000>;
- };
- };
-
-Example for an imx6q-based board, a multi-chipselect device connected to WEIM:
-
-In this case, both chip select 0 and 1 will be configured with the same timing
-array values.
-
- weim: weim@21b8000 {
- compatible = "fsl,imx6q-weim";
- reg = <0x021b8000 0x4000>;
- clocks = <&clks 196>;
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0x08000000 0x02000000
- 1 0 0x0a000000 0x02000000
- 2 0 0x0c000000 0x02000000
- 3 0 0x0e000000 0x02000000>;
- fsl,weim-cs-gpr = <&gpr>;
-
- acme@0 {
- compatible = "acme,whatever";
- reg = <0 0 0x100>, <0 0x400000 0x800>,
- <1 0x400000 0x800>;
- fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100
- 0x00000000 0xa0000240 0x00000000>;
- };
- };
diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
new file mode 100644
index 000000000000..82fc5f4a1ed6
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: i.MX WEIM Bus Peripheral Nodes
+
+maintainers:
+ - Shawn Guo <[email protected]>
+ - Sascha Hauer <[email protected]>
+
+description:
+ This binding is meant for the child nodes of the WEIM node. The node
+ represents any device connected to the WEIM bus. It may be a Flash chip,
+ RAM chip or Ethernet controller, etc. These properties are meant for
+ configuring the WEIM settings/timings and will accompany the bindings
+ supported by the respective device.
+
+properties:
+ reg: true
+
+ fsl,weim-cs-timing:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description:
+ Timing values for the child node.
+ minItems: 2
+ maxItems: 6
+
+# the WEIM child will have its own native properties
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
new file mode 100644
index 000000000000..3f40ca5b13f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
@@ -0,0 +1,204 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,imx-weim.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: i.MX Wireless External Interface Module (WEIM)
+
+maintainers:
+ - Shawn Guo <[email protected]>
+ - Sascha Hauer <[email protected]>
+
+description:
+ The term "wireless" does not imply that the WEIM is literally an interface
+ without wires. It simply means that this module was originally designed for
+ wireless and mobile applications that use low-power technology. The actual
+ devices are instantiated from the child nodes of a WEIM node.
+
+properties:
+ $nodename:
+ pattern: "^memory-controller@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - enum:
+ - fsl,imx1-weim
+ - fsl,imx27-weim
+ - fsl,imx50-weim
+ - fsl,imx51-weim
+ - fsl,imx6q-weim
+ - items:
+ - enum:
+ - fsl,imx31-weim
+ - fsl,imx35-weim
+ - const: fsl,imx27-weim
+ - items:
+ - enum:
+ - fsl,imx6sx-weim
+ - fsl,imx6ul-weim
+ - const: fsl,imx6q-weim
+
+ "#address-cells":
+ const: 2
+
+ "#size-cells":
+ const: 1
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ ranges: true
+
+ fsl,weim-cs-gpr:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: |
+ Phandle to the system General Purpose Register controller that contains
+ WEIM CS GPR register, e.g. IOMUXC_GPR1 on i.MX6Q. IOMUXC_GPR1[11:0]
+ should be set up as one of the following 4 possible values depending on
+ the CS space configuration.
+
+ IOMUXC_GPR1[11:0] CS0 CS1 CS2 CS3
+ ---------------------------------------------
+ 05 128M 0M 0M 0M
+ 033 64M 64M 0M 0M
+ 0113 64M 32M 32M 0M
+ 01111 32M 32M 32M 32M
+
+ In case that the property is absent, the reset value or what bootloader
+ sets up in IOMUXC_GPR1[11:0] will be used.
+
+ fsl,burst-clk-enable:
+ type: boolean
+ description:
+ The presence of this property indicates that the weim bus should operate
+ in Burst Clock Mode.
+
+ fsl,continuous-burst-clk:
+ type: boolean
+ description:
+ Make Burst Clock to output continuous clock. Without this option Burst
+ Clock will output clock only when necessary.
+
+patternProperties:
+ "^.*@[0-7],[0-9a-f]+$":
+ type: object
+ description: Devices attached to chip selects are represented as subnodes.
+ $ref: fsl,imx-weim-peripherals.yaml
+ additionalProperties: true
+ required:
+ - fsl,weim-cs-timing
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - "#address-cells"
+ - "#size-cells"
+ - ranges
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ not:
+ contains:
+ enum:
+ - fsl,imx50-weim
+ - fsl,imx6q-weim
+ then:
+ properties:
+ fsl,weim-cs-gpr: false
+ fsl,burst-clk-enable: false
+ - if:
+ not:
+ required:
+ - fsl,burst-clk-enable
+ then:
+ properties:
+ fsl,continuous-burst-clk: false
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: fsl,imx1-weim
+ then:
+ patternProperties:
+ "^.*@[0-7],[0-9a-f]+$":
+ properties:
+ fsl,weim-cs-timing:
+ items:
+ items:
+ - description: CSxU
+ - description: CSxL
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - fsl,imx27-weim
+ - fsl,imx31-weim
+ - fsl,imx35-weim
+ then:
+ patternProperties:
+ "^.*@[0-7],[0-9a-f]+$":
+ properties:
+ fsl,weim-cs-timing:
+ items:
+ items:
+ - description: CSCRxU
+ - description: CSCRxL
+ - description: CSCRxA
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - fsl,imx50-weim
+ - fsl,imx51-weim
+ - fsl,imx6q-weim
+ - fsl,imx6sx-weim
+ - fsl,imx6ul-weim
+ then:
+ patternProperties:
+ "^.*@[0-7],[0-9a-f]+$":
+ properties:
+ fsl,weim-cs-timing:
+ items:
+ items:
+ - description: CSxGCR1
+ - description: CSxGCR2
+ - description: CSxRCR1
+ - description: CSxRCR2
+ - description: CSxWCR1
+ - description: CSxWCR2
+
+additionalProperties: false
+
+examples:
+ - |
+ memory-controller@21b8000 {
+ compatible = "fsl,imx6q-weim";
+ reg = <0x021b8000 0x4000>;
+ clocks = <&clks 196>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ fsl,weim-cs-gpr = <&gpr>;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x02000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ bank-width = <2>;
+ fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+ 0x0000c000 0x1404a38e 0x00000000>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
index 8d9dae15ade0..00deeb09f87d 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
@@ -37,5 +37,6 @@ allOf:
- $ref: ingenic,nemc-peripherals.yaml#
- $ref: intel,ixp4xx-expansion-peripheral-props.yaml#
- $ref: ti,gpmc-child.yaml#
+ - $ref: fsl/fsl,imx-weim-peripherals.yaml
additionalProperties: true
diff --git a/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt b/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
index b1f9474f36d5..f34a95611645 100644
--- a/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
+++ b/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
@@ -48,7 +48,7 @@ Example of usage:
-----------------
This example places the bridge on top of the i.MX WEIM parallel bus, see:
-Documentation/devicetree/bindings/bus/imx-weim.txt
+Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
&weim {
controller@0,0 {
--
2.43.0
i.MX6UL(L) uses "fsl,imx6sx-lcdif" as fallback compatible string,
but has only very lightweight DISPLAY power domain. Its DISPLAY
power domain is not supported by the binding / Linux kernel at
the moment. Since the current setup is working, let's remove the
power-domain from being required for that platform to fix the warning
printed by CHECK_DTBS=y.
Fixes: f62678a77d58 ("dt-bindings: mxsfb: Document i.MX8M/i.MX6SX/i.MX6SL power-domains property")
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
Documentation/devicetree/bindings/display/fsl,lcdif.yaml | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/display/fsl,lcdif.yaml b/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
index 1c2be8d6f633..0681fc49aa1b 100644
--- a/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
+++ b/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
@@ -120,13 +120,19 @@ allOf:
maxItems: 1
clock-names:
maxItems: 1
+ - if:
+ properties:
+ compatible:
+ const: fsl,imx6sx-lcdif
+ then:
+ required:
+ - power-domains
- if:
properties:
compatible:
contains:
enum:
- fsl,imx6sl-lcdif
- - fsl,imx6sx-lcdif
- fsl,imx8mm-lcdif
- fsl,imx8mn-lcdif
- fsl,imx8mp-lcdif
--
2.43.0
Fix the following warning found via CHECK_DTBS:
tempmon: '#thermal-sensor-cells' is a required property
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 9eb4eee0c272..45b7605ac381 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -638,6 +638,7 @@ tempmon: tempmon {
nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
nvmem-cell-names = "calib", "temp_grade";
clocks = <&clks IMX6UL_CLK_PLL3_USB_OTG>;
+ #thermal-sensor-cells = <0>;
};
};
--
2.43.0
fsl,anatop should only be added to the usbphy nodes.
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index a27a7554c2e7..9eb4eee0c272 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -855,7 +855,6 @@ usbotg1: usb@2184000 {
clocks = <&clks IMX6UL_CLK_USBOH3>;
fsl,usbphy = <&usbphy1>;
fsl,usbmisc = <&usbmisc 0>;
- fsl,anatop = <&anatop>;
ahb-burst-config = <0x0>;
tx-burst-size-dword = <0x10>;
rx-burst-size-dword = <0x10>;
--
2.43.0
DT node names should be generic, so replace "weim" node name with
"memory-controller" in all i.MX SoC DT files.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx1.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx27.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx31.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx35.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx51.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6sl.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6sx.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 2 +-
9 files changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx1.dtsi b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
index 1ac10965fdfd..389ecb1ebf8f 100644
--- a/arch/arm/boot/dts/nxp/imx/imx1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
@@ -251,7 +251,7 @@ gpio4: gpio@21c300 {
};
};
- weim: weim@220000 {
+ weim: memory-controller@220000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx1-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
index ec472695c71e..ec3ccc8f4095 100644
--- a/arch/arm/boot/dts/nxp/imx/imx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
@@ -568,7 +568,7 @@ nfc: nand-controller@d8000000 {
status = "disabled";
};
- weim: weim@d8002000 {
+ weim: memory-controller@d8002000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx27-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx31.dtsi b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
index e1ae7c175f7d..00006c90d9a7 100644
--- a/arch/arm/boot/dts/nxp/imx/imx31.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
@@ -352,7 +352,7 @@ nfc: nand@b8000000 {
status = "disabled";
};
- weim: weim@b8002000 {
+ weim: memory-controller@b8002000 {
compatible = "fsl,imx31-weim", "fsl,imx27-weim";
reg = <0xb8002000 0x1000>;
clocks = <&clks 56>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx35.dtsi b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
index 2d20e5541acc..442dc15677b8 100644
--- a/arch/arm/boot/dts/nxp/imx/imx35.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
@@ -374,7 +374,7 @@ nfc: nand@bb000000 {
status = "disabled";
};
- weim: weim@b8002000 {
+ weim: memory-controller@b8002000 {
#address-cells = <2>;
#size-cells = <1>;
clocks = <&clks 0>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx51.dtsi b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
index c96d6311dfa7..4efce49022e4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx51.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
@@ -578,7 +578,7 @@ m4if: m4if@83fd8000 {
reg = <0x83fd8000 0x1000>;
};
- weim: weim@83fda000 {
+ weim: memory-controller@83fda000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx51-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
index 81142c523fa8..8431b8a994f4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
@@ -1158,7 +1158,7 @@ mmdc1: memory-controller@21b4000 { /* MMDC1 */
status = "disabled";
};
- weim: weim@21b8000 {
+ weim: memory-controller@21b8000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx6q-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
index 28111efb19a6..6aa61235e39e 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
@@ -949,7 +949,7 @@ rngb: rngb@21b4000 {
clocks = <&clks IMX6SL_CLK_DUMMY>;
};
- weim: weim@21b8000 {
+ weim: memory-controller@21b8000 {
#address-cells = <2>;
#size-cells = <1>;
reg = <0x021b8000 0x4000>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
index df3a375f0a3e..0de359d62a47 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
@@ -1107,7 +1107,7 @@ fec2: ethernet@21b4000 {
status = "disabled";
};
- weim: weim@21b8000 {
+ weim: memory-controller@21b8000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx6sx-weim", "fsl,imx6q-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 8aa365f837ca..aeb7e07fd309 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -975,7 +975,7 @@ memory-controller@21b0000 {
clocks = <&clks IMX6UL_CLK_MMDC_P0_IPG>;
};
- weim: weim@21b8000 {
+ weim: memory-controller@21b8000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx6ul-weim", "fsl,imx6q-weim";
--
2.43.0
Uni-Trend Technology is a manufacturer of measurement
and testing tools.
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 1a0dc04f1db4..e945e76696c2 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1484,6 +1484,8 @@ patternProperties:
description: Ufi Space Co., Ltd.
"^ugoos,.*":
description: Ugoos Industrial Co., Ltd.
+ "^uni-t,.*":
+ description: Uni-Trend Technology (China) Co., Ltd.
"^uniwest,.*":
description: United Western Technologies Corp (UniWest)
"^upisemi,.*":
--
2.43.0
Replace all "xnur-gpio" with "xnur-gpios" in the i.MX6UL(L) Touchscreen
node, since the -gpio suffix is deprecated. All known implementations of
this binding can handle -gpio and -gpios since day 1, so this should be
fully backwards compatible.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi | 2 +-
4 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
index 2ac40d69425b..f10f0525490b 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
@@ -321,7 +321,7 @@ &snvs_pwrkey {
&tsc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
measure-delay-time = <0xffff>;
pre-charge-time = <0xfff>;
status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
index 875ae699c5cb..2ca18f3dad0a 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
@@ -203,7 +203,7 @@ &pwm8 {
&tsc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
};
&sai2 {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
index 18cac19aa9b0..af337f18a266 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
@@ -156,7 +156,7 @@ &snvs_pwrkey {
&tsc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
measure-delay-time = <0xffff>;
pre-charge-time = <0xffff>;
status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
index 830b5a5064f2..6d2163250b5d 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
@@ -273,7 +273,7 @@ &tsc {
pinctrl-names = "default";
pre-charge-time = <0xfff>;
touchscreen-average-samples = <32>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
};
/* DHCOM UART1 */
--
2.43.0
pinctrl node name must be either pinctrl or pinmux.
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx6ull.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
index 2bccd45e9fc2..8a1776067ecc 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
@@ -75,7 +75,7 @@ rngb: rng@2284000 {
clocks = <&clks IMX6UL_CLK_DUMMY>;
};
- iomuxc_snvs: iomuxc-snvs@2290000 {
+ iomuxc_snvs: pinctrl@2290000 {
compatible = "fsl,imx6ull-iomuxc-snvs";
reg = <0x02290000 0x4000>;
};
--
2.43.0
Add compatibles used by different i.MX6 variants to the i.MX IOMUX
Controller GPR binding.
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
.../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml | 18 +++++++++++++++++-
1 file changed, 17 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
index 1da1b758b4ae..8451cb4dd87c 100644
--- a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
+++ b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
@@ -17,7 +17,23 @@ properties:
compatible:
oneOf:
- items:
- - const: fsl,imx8mq-iomuxc-gpr
+ - enum:
+ - fsl,imx6q-iomuxc-gpr
+ - fsl,imx8mq-iomuxc-gpr
+ - const: syscon
+ - const: simple-mfd
+ - items:
+ - enum:
+ - fsl,imx6sl-iomuxc-gpr
+ - fsl,imx6sll-iomuxc-gpr
+ - fsl,imx6ul-iomuxc-gpr
+ - const: fsl,imx6q-iomuxc-gpr
+ - const: syscon
+ - items:
+ - enum:
+ - fsl,imx6sx-iomuxc-gpr
+ - fsl,imx7d-iomuxc-gpr
+ - const: fsl,imx6q-iomuxc-gpr
- const: syscon
- const: simple-mfd
- items:
--
2.43.0
Add compatible value for i.MX6ULL based UNI-T UTi260B thermal camera.
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 228dcc5c7d6f..7b65f9c9c1a5 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -708,6 +708,7 @@ properties:
- toradex,colibri-imx6ull # Colibri iMX6ULL Modules
- toradex,colibri-imx6ull-emmc # Colibri iMX6ULL 1GB (eMMC) Module
- toradex,colibri-imx6ull-wifi # Colibri iMX6ULL Wi-Fi / BT Modules
+ - uni-t,uti260b # UNI-T UTi260B Thermal Camera
- const: fsl,imx6ull
- description: i.MX6ULL Armadeus Systems OPOS6ULDev Board
--
2.43.0
The canonical node name for touchscreens is "touchscreen",
so update the i.MX6UL "tsc" node accordingly.
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 45b7605ac381..8aa365f837ca 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -370,7 +370,7 @@ asrc: asrc@2034000 {
};
};
- tsc: tsc@2040000 {
+ tsc: touchscreen@2040000 {
compatible = "fsl,imx6ul-tsc";
reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
--
2.43.0
HDMI Audio has been added to the DT binding documentation with an
incorrect index. DT and the driver use index 26. This happened,
because the binding is missing MULTI_SAI type, which is using
index 25.
Reported-by: Michael Yackavage <[email protected]>
Fixes: 7bdbd87d4008 ("dt-bindings: fsl-imx-sdma: Convert imx sdma to DT schema")
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml b/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
index b95dd8db5a30..37135fa024f9 100644
--- a/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
+++ b/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
@@ -92,7 +92,8 @@ properties:
description: needs firmware more than ver 2
- Shared ASRC: 23
- SAI: 24
- - HDMI Audio: 25
+ - Multi SAI: 25
+ - HDMI Audio: 26
The third cell: transfer priority ID
enum:
--
2.43.0
Add UNI-T UTi260b thermal camera board.
Reviewed-by: Stefan Wahren <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts | 567 ++++++++++++++++++
2 files changed, 568 insertions(+)
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a0..47350cf3ddeb 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -349,6 +349,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-tarragon-slavext.dtb \
imx6ull-tqma6ull2-mba6ulx.dtb \
imx6ull-tqma6ull2l-mba6ulx.dtb \
+ imx6ull-uti260b.dtb \
imx6ulz-14x14-evk.dtb \
imx6ulz-bsh-smm-m2.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
new file mode 100644
index 000000000000..8f6f092363b7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
@@ -0,0 +1,567 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2022-2024 Sebastian Reichel <[email protected]>
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "UNI-T UTi260B Thermal Camera";
+ compatible = "uni-t,uti260b", "fsl,imx6ull";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_led_ctrl>;
+
+ led {
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_FLASH;
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_gpio_keys>;
+ autorepeat;
+
+ up-key {
+ label = "Up";
+ gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_UP>;
+ };
+
+ down-key {
+ label = "Down";
+ gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_DOWN>;
+ };
+
+ left-key {
+ label = "Left";
+ gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LEFT>;
+ };
+
+ right-key {
+ label = "Right";
+ gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RIGHT>;
+ };
+
+ ok-key {
+ label = "Ok";
+ gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_ENTER>;
+ };
+
+ return-key {
+ label = "Return";
+ gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_ESC>;
+ };
+
+ play-key {
+ label = "Media";
+ gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MEDIA>;
+ };
+
+ trigger-key {
+ label = "Trigger";
+ gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_TRIGGER>;
+ };
+
+ power-key {
+ label = "Power";
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ };
+
+ light-key {
+ label = "Light";
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LIGHTS_TOGGLE>;
+ };
+ };
+
+ panel_backlight: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ enable-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_backlight_enable>;
+ power-supply = <®_vsd>;
+ pwms = <&pwm1 0 50000 0>;
+ };
+
+ reg_vsd: regulator-vsd {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_vref: regulator-vref-4v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "VREF_4V2";
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+ };
+
+ tp5000: charger {
+ compatible = "gpio-charger";
+ charger-type = "usb-sdp";
+ gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_charger_stat1>;
+ };
+
+ battery: battery {
+ compatible = "simple-battery";
+ /* generic 26650 battery */
+ device-chemistry = "lithium-ion";
+ charge-full-design-microamp-hours = <5000000>;
+ voltage-max-design-microvolt = <4200000>;
+ voltage-min-design-microvolt = <3300000>;
+ };
+
+ fuel-gauge {
+ compatible = "adc-battery";
+ charged-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ io-channel-names = "voltage";
+ io-channels = <&adc1 7>;
+ monitored-battery = <&battery>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_charger_stat2>;
+ power-supplies = <&tp5000>;
+ };
+
+ poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_poweroff>;
+ };
+};
+
+&gpio1 {
+ ir-reset-hog {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ line-name = "ir-reset-gpio";
+ output-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_ir_reset>;
+ };
+};
+
+&gpio2 {
+ /* configuring this to output-high results in poweroff */
+ power-en-hog {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ line-name = "power-en-gpio";
+ output-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_poweroff2>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_spi3>;
+ status = "okay";
+
+ panel@0 {
+ compatible = "inanbo,t28cp45tn89-v17";
+ reg = <0>;
+ backlight = <&panel_backlight>;
+ power-supply = <®_vsd>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <1000000>;
+ spi-rx-bus-width = <0>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_uart>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_pwm>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_i2c1>;
+ status = "okay";
+
+ camera@21 {
+ compatible = "galaxycore,gc0308";
+ reg = <0x21>;
+ clocks = <&clks IMX6UL_CLK_CSI>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_gc0308>;
+ powerdown-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ vdd28-supply = <®_vsd>;
+
+ port {
+ gc0308_to_parallel: endpoint {
+ remote-endpoint = <¶llel_from_gc0308>;
+ bus-width = <8>;
+ data-shift = <2>; /* lines 9:2 are used */
+ hsync-active = <1>; /* active high */
+ vsync-active = <1>; /* active high */
+ data-active = <1>; /* active high */
+ pclk-sample = <1>; /* sample on rising edge */
+ };
+ };
+ };
+};
+
+&csi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_csi>;
+
+ port {
+ parallel_from_gc0308: endpoint {
+ remote-endpoint = <&gc0308_to_parallel>;
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_i2c2>;
+ status = "okay";
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&lcdif {
+ assigned-clocks = <&clks IMX6UL_CLK_LCDIF_PRE_SEL>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL5_VIDEO_DIV>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_lcd_data>, <&mux_lcd_ctrl>;
+ status = "okay";
+
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+};
+
+&usdhc1 {
+ /* MicroSD */
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ no-1-8-v;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&mux_sdhc1>, <&mux_sdhc1_cd>;
+ pinctrl-1 = <&mux_sdhc1_100mhz>, <&mux_sdhc1_cd>;
+ pinctrl-2 = <&mux_sdhc1_200mhz>, <&mux_sdhc1_cd>;
+ wakeup-source;
+ vmmc-supply = <®_vsd>;
+ status = "okay";
+};
+
+&usdhc2 {
+ /* eMMC */
+ keep-power-in-suspend;
+ no-1-8-v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_sdhc2>;
+ wakeup-source;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_wdog>;
+};
+
+&adc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_adc>;
+ vref-supply = <®_vref>;
+ #io-channel-cells = <1>;
+ status = "okay";
+};
+
+&usbotg1 {
+ /* USB-C connector */
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbotg2 {
+ /* thermal sensor */
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <106>;
+};
+
+&iomuxc {
+ mux_ir_reset: irresetgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x3008
+ >;
+ };
+
+ mux_poweroff: poweroffgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04 0x3008
+ >;
+ };
+
+ mux_poweroff2: poweroff2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_TX_CLK__GPIO2_IO06 0x3008
+ >;
+ };
+
+ mux_charger_stat1: charger1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x3008
+ >;
+ };
+
+ mux_charger_stat2: charger2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x3008
+ >;
+ };
+
+ mux_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
+
+ mux_sdhc1_cd: sdhc1-cd-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ mux_sdhc1: sdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ >;
+ };
+
+ mux_sdhc1_100mhz: sdhc1-100mhz-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x170b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ mux_sdhc1_200mhz: sdhc1-200mhz-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x170f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ mux_sdhc2: sdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+ >;
+ };
+
+ mux_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ mux_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001f8a8
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001f8a8
+ >;
+ };
+
+ mux_uart: uartgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ mux_gpio_keys: gpiokeygrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x3008
+ MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x3008
+ MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x3008
+ MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x3008
+ MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x3008
+ MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x3008
+ MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x3008
+ MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x3008
+ MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03 0x3008
+ MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01 0x3008
+ >;
+ };
+
+ mux_led_ctrl: ledctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02 0x3008
+ >;
+ };
+
+ mux_adc: adcgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__GPIO1_IO07 0xb0
+ >;
+ };
+
+ mux_pwm: pwm1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
+ >;
+ };
+
+ mux_backlight_enable: blenablegrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x3008
+ >;
+ };
+
+ mux_lcd_data: lcdifdatgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
+ >;
+ };
+
+ mux_lcd_ctrl: lcdifctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
+ >;
+ };
+
+ mux_csi: csi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
+ MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
+ MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088
+ MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088
+ MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088
+ MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088
+ MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088
+ MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088
+ MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088
+ MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088
+ MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088
+ >;
+ };
+
+ mux_gc0308: gc0308grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1e038
+ MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x1b088
+ MX6UL_PAD_GPIO1_IO06__GPIO1_IO06 0x1b088
+ >;
+ };
+
+
+ mux_spi3: ecspi3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x100b1
+ MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x100b1
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x3008
+ >;
+ };
+};
--
2.43.0
On Sat, Feb 24, 2024 at 6:33 PM Sebastian Reichel <[email protected]> wrote:
>
> i.MX6UL(L) uses "fsl,imx6sx-lcdif" as fallback compatible string,
> but has only very lightweight DISPLAY power domain. Its DISPLAY
> power domain is not supported by the binding / Linux kernel at
> the moment. Since the current setup is working, let's remove the
> power-domain from being required for that platform to fix the warning
> printed by CHECK_DTBS=y.
Thanks, this also fixes the following imx8mq warnings:
imx8mq-evk.dtb: lcd-controller@30320000: 'power-domains' is a required property
from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml#
Reviewed-by: Fabio Estevam <[email protected]>
On Sat, Feb 24, 2024 at 6:33 PM Sebastian Reichel <[email protected]> wrote:
> +&gpio2 {
> + /* configuring this to output-high results in poweroff */
> + power-en-hog {
> + gpio-hog;
> + gpios = <6 GPIO_ACTIVE_HIGH>;
> + line-name = "power-en-gpio";
> + output-low;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mux_poweroff2>;
> + };
> +};
> +
> +&ecspi3 {
It is recommended to put the nodes in alphabetical order (except
iomuxc, which is the last one).
> + mux_gc0308: gc0308grp {
> + fsl,pins = <
> + MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1e038
> + MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x1b088
> + MX6UL_PAD_GPIO1_IO06__GPIO1_IO06 0x1b088
> + >;
> + };
> +
> +
There is an extra blank line here.
Reviewed-by: Fabio Estevam <[email protected]>
On Sat, Feb 24, 2024 at 10:29:42PM +0100, Sebastian Reichel wrote:
> Fix the following warning found via CHECK_DTBS:
>
> tempmon: '#thermal-sensor-cells' is a required property
>
> Signed-off-by: Sebastian Reichel <[email protected]>
Thanks for the patch! But I had picked up the one [1] from Alexander
Stein.
Shawn
[1] https://lore.kernel.org/linux-arm-kernel/ZcCNdrQPb10i4rl2@t480/T/
On Sat, Feb 24, 2024 at 10:29:40PM +0100, Sebastian Reichel wrote:
> pinctrl node name must be either pinctrl or pinmux.
>
> Reviewed-by: Linus Walleij <[email protected]>
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>
Applied, thanks!
On Sat, Feb 24, 2024 at 10:29:41PM +0100, Sebastian Reichel wrote:
> fsl,anatop should only be added to the usbphy nodes.
>
> Signed-off-by: Sebastian Reichel <[email protected]>
Applied, thanks!
On Sat, Feb 24, 2024 at 10:29:43PM +0100, Sebastian Reichel wrote:
> Replace all "xnur-gpio" with "xnur-gpios" in the i.MX6UL(L) Touchscreen
> node, since the -gpio suffix is deprecated. All known implementations of
> this binding can handle -gpio and -gpios since day 1, so this should be
> fully backwards compatible.
>
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>
Applied, thanks!
On Sat, Feb 24, 2024 at 10:29:44PM +0100, Sebastian Reichel wrote:
> The canonical node name for touchscreens is "touchscreen",
> so update the i.MX6UL "tsc" node accordingly.
>
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>
Applied, thanks!
On Sat, Feb 24, 2024 at 10:29:46PM +0100, Sebastian Reichel wrote:
> Uni-Trend Technology is a manufacturer of measurement
> and testing tools.
>
> Acked-by: Krzysztof Kozlowski <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>
Applied, thanks!
On Sat, Feb 24, 2024 at 10:29:45PM +0100, Sebastian Reichel wrote:
> DT node names should be generic, so replace "weim" node name with
> "memory-controller" in all i.MX SoC DT files.
>
> Reviewed-by: Krzysztof Kozlowski <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>
Applied, thanks!
On Sat, Feb 24, 2024 at 10:29:47PM +0100, Sebastian Reichel wrote:
> Add compatible value for i.MX6ULL based UNI-T UTi260B thermal camera.
>
> Acked-by: Krzysztof Kozlowski <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>
Applied, thanks!
On Sat, Feb 24, 2024 at 10:29:48PM +0100, Sebastian Reichel wrote:
> Add UNI-T UTi260b thermal camera board.
>
> Reviewed-by: Stefan Wahren <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>
Can we change the patch subject to something like below?
ARM: dts: imx: Add UNI-T UTi260b thermal camera board
Shawn
On Sat, 24 Feb 2024 22:29:34 +0100, Sebastian Reichel wrote:
> Convert the i.MX Wireless External Interface Module binding to YAML.
>
>
Applied, thanks!
[02/16] dt-bindings: bus: imx-weim: convert to YAML
https://git.kernel.org/krzk/linux-mem-ctrl/c/3884bdce169de87d3f978edf41829e5e52388072
Best regards,
--
Krzysztof Kozlowski <[email protected]>
On Sat, 24 Feb 2024 22:29:38 +0100, Sebastian Reichel wrote:
> i.MX6UL(L) uses "fsl,imx6sx-lcdif" as fallback compatible string,
> but has only very lightweight DISPLAY power domain. Its DISPLAY
> power domain is not supported by the binding / Linux kernel at
> the moment. Since the current setup is working, let's remove the
> power-domain from being required for that platform to fix the warning
> printed by CHECK_DTBS=y.
>
> Fixes: f62678a77d58 ("dt-bindings: mxsfb: Document i.MX8M/i.MX6SX/i.MX6SL power-domains property")
> Acked-by: Krzysztof Kozlowski <[email protected]>
> Signed-off-by: Sebastian Reichel <[email protected]>
> ---
> Documentation/devicetree/bindings/display/fsl,lcdif.yaml | 8 +++++++-
> 1 file changed, 7 insertions(+), 1 deletion(-)
>
Applied, thanks!