LinuxLists.cc - [PATCH v4 0/3] arm64: qcom: sm8650: add support for the SM8650-HDK board

2024-04-22 08:49:51

Subject: [PATCH v4 0/3] arm64: qcom: sm8650: add support for the SM8650-HDK board

2024-04-22 08:50:02

Subject: [PATCH v4 3/3] arch: arm64: dts: sm8650-hdk: add support for the Display Card overlay

With the SM8650-HDK, a Display Card kit can be connected to provide
a VTDR6130 display with Goodix Berlin Touch controller.

In order to route the DSI lanes to the connector for the Display
Card kit, a switch must be changed on the board.

The HDMI nodes are disabled since the DSI lanes are shared with
the DSI to HDMI transceiver.

Add support for this card as an overlay and apply it it at
build-time to the sm8650-hdk dtb.

Reviewed-by: Vladimir Zapolskiy <[email protected]>
Tested-by: Vladimir Zapolskiy <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 4 +
.../boot/dts/qcom/sm8650-hdk-display-card.dtso | 144 +++++++++++++++++++++
2 files changed, 148 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 74e6796eb5eb..640c8fb499fe 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -242,6 +242,10 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-sony-xperia-yodo-pdx234.dtb
+
+sm8650-hdk-display-card-dtbs := sm8650-hdk.dtb sm8650-hdk-display-card.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM) += sm8650-hdk-display-card.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8650-hdk-display-card.dtso b/arch/arm64/boot/dts/qcom/sm8650-hdk-display-card.dtso
new file mode 100644
index 000000000000..83f2338e5bf4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8650-hdk-display-card.dtso
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Linaro Limited
+ */
+
+/*
+ * Display Card kit overlay
+ * This requires S5702 Switch 7 to be turned to OFF to route DSI0 to the display panel
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+/plugin/;
+
+&i2c6 {
+ status = "disabled";
+};
+
+&lt9611_1v2 {
+ status = "disabled";
+};
+
+&lt9611_3v3 {
+ status = "disabled";
+};
+
+&vreg_bob_3v3 {
+ status = "disabled";
+};
+
+&lt9611_codec {
+ status = "disabled";
+};
+
+&mdss_dsi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel@0 {
+ compatible = "visionox,vtdr6130";
+ reg = <0>;
+
+ reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+ vddio-supply = <&vreg_l12b_1p8>;
+ vci-supply = <&vreg_l13b_3p0>;
+ vdd-supply = <&vreg_l11b_1p2>;
+
+ pinctrl-0 = <&disp0_reset_n_active>, <&mdp_vsync>;
+ pinctrl-1 = <&disp0_reset_n_suspend>, <&mdp_vsync>;
+ pinctrl-names = "default", "sleep";
+
+ port {
+ panel0_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+ };
+
+ /*
+ * DTC requires to have both endpoints when compiling the overlay
+ * and also requires the #address/size-cells + reg properties
+ */
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ mdss_dsi0_out: endpoint {
+ remote-endpoint = <&panel0_in>;
+ };
+ };
+ };
+};
+
+&spi4 {
+ /* DTC requires the #address/size-cells to compile DTBO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ touchscreen@0 {
+ compatible = "goodix,gt9916";
+ reg = <0>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <162 IRQ_TYPE_LEVEL_LOW>;
+
+ reset-gpios = <&tlmm 161 GPIO_ACTIVE_LOW>;
+
+ avdd-supply = <&vreg_l14b_3p2>;
+
+ spi-max-frequency = <1000000>;
+
+ touchscreen-size-x = <1080>;
+ touchscreen-size-y = <2400>;
+
+ pinctrl-0 = <&ts_irq>, <&ts_reset>;
+ pinctrl-names = "default";
+ };
+};
+
+&tlmm {
+ disp0_reset_n_active: disp0-reset-n-active-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ disp0_reset_n_suspend: disp0-reset-n-suspend-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ mdp_vsync: mdp-vsync-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ ts_irq: ts-irq-state {
+ pins = "gpio161";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ output-disable;
+ };
+
+ ts_reset: ts-reset-state {
+ pins = "gpio162";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};

--
2.34.1

2024-04-22 08:50:27

by Neil Armstrong

[permalink] [raw]

Subject: [PATCH v4 2/3] arm64: dts: qcom: sm8650: add support for the SM8650-HDK board

The SM8650-HDK is an embedded development platforms for the
Snapdragon 8 Gen 3 SoC aka SM8650, with the following features:
- Qualcomm SM8650 SoC
- 16GiB On-board LPDDR5
- On-board WiFi 7 + Bluetooth 5.3/BLE
- On-board UFS4.0
- M.2 Key B+M Gen3x2 PCIe Slot
- HDMI Output
- USB-C Connector with DP Almode & Audio Accessory mode
- Micro-SDCard Slot
- Audio Jack with Playback and Microphone
- 2 On-board Analog microphones
- 2 On-board Speakers
- 96Boards Compatible Low-Speed and High-Speed connectors [1]
- For Camera, Sensors and external Display cards
- Compatible with the Linaro Debug board [2]
- SIM Slot for Modem
- Debug connectors
- 6x On-Board LEDs

Product Page: [3]

[1] https://www.96boards.org/specifications/
[2] https://git.codelinaro.org/linaro/qcomlt/debugboard
[3] https://www.lantronix.com/products/snapdragon-8-gen-3-mobile-hardware-development-kit/

Reviewed-by: Konrad Dybcio <[email protected]>
Reviewed-by: Vladimir Zapolskiy <[email protected]>
Tested-by: Vladimir Zapolskiy <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8650-hdk.dts | 1251 +++++++++++++++++++++++++++++++
2 files changed, 1252 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f63abb43e9fe..74e6796eb5eb 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -242,6 +242,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8550-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8550-sony-xperia-yodo-pdx234.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8650-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8650-hdk.dts b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
new file mode 100644
index 000000000000..3791c36579be
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
@@ -0,0 +1,1251 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8650.dtsi"
+#include "pm8010.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 8
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. SM8650 HDK";
+ compatible = "qcom,sm8650-hdk", "qcom,sm8650";
+ chassis-type = "embedded";
+
+ aliases {
+ serial0 = &uart15;
+ serial1 = &uart14;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_out: endpoint {
+ remote-endpoint = <&lt9611_out>;
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&volume_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_BLUETOOTH;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pm8550b_gpios 9 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ panic-indicator;
+ };
+
+ led-2 {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_ORANGE>;
+ gpios = <&pm8550b_gpios 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,sm8650-pmic-glink",
+ "qcom,sm8550-pmic-glink",
+ "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_dp_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu: endpoint {
+ remote-endpoint = <&wcd_usbss_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ lt9611_1v2: regulator-lt9611-1v2 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "LT9611_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ vin-supply = <&vph_pwr>;
+ gpio = <&tlmm 79 GPIO_ACTIVE_HIGH>;
+
+ enable-active-high;
+ };
+
+ lt9611_3v3: regulator-lt9611-3v3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "LT9611_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ vin-supply = <&vreg_bob_3v3>;
+ gpio = <&tlmm 78 GPIO_ACTIVE_HIGH>;
+
+ enable-active-high;
+ };
+
+ sound {
+ compatible = "qcom,sm8650-sndcard", "qcom,sm8450-sndcard";
+ model = "SM8650-HDK";
+ audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
+ "SpkrRight IN", "WSA_SPK2 OUT",
+ "IN1_HPHL", "HPHL_OUT",
+ "IN2_HPHR", "HPHR_OUT",
+ "AMIC1", "MIC BIAS1",
+ "AMIC2", "MIC BIAS2",
+ "AMIC5", "MIC BIAS4",
+ "TX SWR_INPUT0", "ADC1_OUTPUT",
+ "TX SWR_INPUT1", "ADC2_OUTPUT",
+ "TX SWR_INPUT3", "ADC4_OUTPUT";
+
+ wcd-playback-dai-link {
+ link-name = "WCD Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&wcd939x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-capture-dai-link {
+ link-name = "WCD Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+ };
+
+ codec {
+ sound-dai = <&wcd939x 1>, <&swr2 0>, <&lpass_txmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&north_spkr>, <&south_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
+ vph_pwr: regulator-vph-pwr {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vreg_bob_3v3: regulator-vreg-bob-3v3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_BOB_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ vin-supply = <&vph_pwr>;
+ };
+
+ wcd939x: audio-codec {
+ compatible = "qcom,wcd9395-codec", "qcom,wcd9390-codec";
+
+ pinctrl-0 = <&wcd_default>;
+ pinctrl-names = "default";
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ reset-gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+
+ vdd-buck-supply = <&vreg_l15b_1p8>;
+ vdd-rxtx-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l15b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob1>;
+
+ #sound-dai-cells = <1>;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+
+ vdd-bob1-supply = <&vph_pwr>;
+ vdd-bob2-supply = <&vph_pwr>;
+ vdd-l2-l13-l14-supply = <&vreg_bob1>;
+ vdd-l3-supply = <&vreg_s1c_1p2>;
+ vdd-l5-l16-supply = <&vreg_bob1>;
+ vdd-l6-l7-supply = <&vreg_bob1>;
+ vdd-l8-l9-supply = <&vreg_bob1>;
+ vdd-l11-supply = <&vreg_s1c_1p2>;
+ vdd-l12-supply = <&vreg_s6c_1p8>;
+ vdd-l15-supply = <&vreg_s6c_1p8>;
+ vdd-l17-supply = <&vreg_bob2>;
+
+ qcom,pmic-id = "b";
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2720000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p1: ldo5 {
+ regulator-name = "vreg_l5b_3p1";
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_1p8: ldo7 {
+ regulator-name = "vreg_l7b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_1p8: ldo8 {
+ regulator-name = "vreg_l8b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_1p2: ldo11 {
+ regulator-name = "vreg_l11b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p8: ldo12 {
+ regulator-name = "vreg_l12b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p2: ldo14 {
+ regulator-name = "vreg_l14b_3p2";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16b_2p8: ldo16 {
+ regulator-name = "vreg_l16b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+
+ vdd-l1-supply = <&vreg_s1c_1p2>;
+ vdd-l2-supply = <&vreg_s1c_1p2>;
+ vdd-l3-supply = <&vreg_s1c_1p2>;
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+
+ qcom,pmic-id = "c";
+
+ vreg_s1c_1p2: smps1 {
+ regulator-name = "vreg_s1c_1p2";
+ regulator-min-microvolt = <1256000>;
+ regulator-max-microvolt = <1348000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2c_0p8: smps2 {
+ regulator-name = "vreg_s2c_0p8";
+ regulator-min-microvolt = <852000>;
+ regulator-max-microvolt = <1036000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s3c_0p9: smps3 {
+ regulator-name = "vreg_s3c_0p9";
+ regulator-min-microvolt = <976000>;
+ regulator-max-microvolt = <1064000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4c_1p2: smps4 {
+ regulator-name = "vreg_s4c_1p2";
+ regulator-min-microvolt = <1224000>;
+ regulator-max-microvolt = <1280000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5c_0p7: smps5 {
+ regulator-name = "vreg_s5c_0p7";
+ regulator-min-microvolt = <752000>;
+ regulator-max-microvolt = <900000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6c_1p8: smps6 {
+ regulator-name = "vreg_s6c_1p8";
+ regulator-min-microvolt = <1856000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c_1p2: ldo1 {
+ regulator-name = "vreg_l1c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_1p2: ldo3 {
+ regulator-name = "vreg_l3c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+
+ vdd-l1-supply = <&vreg_s3c_0p9>;
+
+ qcom,pmic-id = "d";
+
+ vreg_l1d_0p88: ldo1 {
+ regulator-name = "vreg_l1d_0p88";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+
+ vdd-l3-supply = <&vreg_s3c_0p9>;
+
+ qcom,pmic-id = "e";
+
+ vreg_l3e_0p9: ldo3 {
+ regulator-name = "vreg_l3e_0p9";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+
+ vdd-l1-supply = <&vreg_s3c_0p9>;
+ vdd-l3-supply = <&vreg_s3c_0p9>;
+
+ qcom,pmic-id = "g";
+
+ vreg_l1g_0p91: ldo1 {
+ regulator-name = "vreg_l1g_0p91";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3g_0p91: ldo3 {
+ regulator-name = "vreg_l3g_0p91";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-5 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+
+ vdd-l1-supply = <&vreg_s3c_0p9>;
+ vdd-l2-supply = <&vreg_s3c_0p9>;
+ vdd-l3-supply = <&vreg_s1c_1p2>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ qcom,pmic-id = "i";
+
+ vreg_s4i_0p85: smps4 {
+ regulator-name = "vreg_s4i_0p85";
+ regulator-min-microvolt = <852000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1i_0p88: ldo1 {
+ regulator-name = "vreg_l1i_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2i_0p88: ldo2 {
+ regulator-name = "vreg_l2i_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3i_1p2: ldo3 {
+ regulator-name = "vreg_l3i_0p91";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-6 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "m";
+
+ vdd-l1-l2-supply = <&vreg_s1c_1p2>;
+ vdd-l3-l4-supply = <&vreg_bob2>;
+ vdd-l5-supply = <&vreg_s6c_1p8>;
+ vdd-l6-supply = <&vreg_bob1>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1m_1p1: ldo1 {
+ regulator-name = "vreg_l1m_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2m_1p056: ldo2 {
+ regulator-name = "vreg_l2m_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3m_2p8: ldo3 {
+ regulator-name = "vreg_l3m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4m_2p8: ldo4 {
+ regulator-name = "vreg_l4m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5m_1p8: ldo5 {
+ regulator-name = "vreg_l5m_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6m_2p8: ldo6 {
+ regulator-name = "vreg_l6m_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7m_2p96: ldo7 {
+ regulator-name = "vreg_l7m_2p96";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-7 {
+ compatible = "qcom,pm8010-rpmh-regulators";
+ qcom,pmic-id = "n";
+
+ vdd-l1-l2-supply = <&vreg_s1c_1p2>;
+ vdd-l3-l4-supply = <&vreg_s6c_1p8>;
+ vdd-l5-supply = <&vreg_bob2>;
+ vdd-l6-supply = <&vreg_bob2>;
+ vdd-l7-supply = <&vreg_bob1>;
+
+ vreg_l1n_1p1: ldo1 {
+ regulator-name = "vreg_l1n_1p1";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2n_1p056: ldo2 {
+ regulator-name = "vreg_l2n_1p056";
+ regulator-min-microvolt = <1056000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3n_1p8: ldo3 {
+ regulator-name = "vreg_l3n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4n_1p8: ldo4 {
+ regulator-name = "vreg_l4n_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5n_2p8: ldo5 {
+ regulator-name = "vreg_l5n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6n_2p8: ldo6 {
+ regulator-name = "vreg_l6n_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7n_3p3: ldo7 {
+ regulator-name = "vreg_l7n_3p3";
+ regulator-min-microvolt = <3304000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&dispcc {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+
+ wcd_usbss: typec-mux@e {
+ compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss";
+ reg = <0xe>;
+
+ vdd-supply = <&vreg_l15b_1p8>;
+ reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>;
+
+ mode-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ wcd_usbss_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_sbu>;
+ };
+ };
+ };
+ };
+};
+
+&i2c6 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ lt9611_codec: hdmi-bridge@2b {
+ compatible = "lontium,lt9611uxc";
+ reg = <0x2b>;
+
+ interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
+
+ reset-gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
+
+ vdd-supply = <&lt9611_1v2>;
+ vcc-supply = <&lt9611_3v3>;
+
+ pinctrl-0 = <&lt9611_irq_pin>, <&lt9611_rst_pin>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ lt9611_a: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ lt9611_out: endpoint {
+ remote-endpoint = <&hdmi_connector_out>;
+ };
+ };
+ };
+ };
+};
+
+&ipa {
+ qcom,gsi-loader = "self";
+ memory-region = <&ipa_fw_mem>;
+ firmware-name = "qcom/sm8650/ipa_fws.mbn";
+ status = "okay";
+};
+
+&lpass_tlmm {
+ spkr_1_sd_n_active: spkr-1-sd-n-active-state {
+ pins = "gpio21";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&lt9611_a>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l1i_0p88>;
+
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1>;
+ remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1i_0p88>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
+&pcie1 {
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie1_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l3e_0p9>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+ vdda-qref-supply = <&vreg_l1i_0p88>;
+
+ status = "okay";
+};
+
+&pm8550_gpios {
+ sdc2_card_det_n: sdc2-card-det-state {
+ pins = "gpio12";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ output-disable;
+ power-source = <1>; /* 1.8 V */
+ };
+
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ bias-pull-up;
+ input-enable;
+ power-source = <1>;
+ };
+};
+
+/* The RGB signals are routed to 3 separate LEDs on the HDK8650 */
+&pm8550_pwm {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ led@1 {
+ reg = <1>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ };
+
+ led@2 {
+ reg = <2>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ };
+
+ led@3 {
+ reg = <3>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "off";
+ };
+};
+
+&pm8550b_eusb2_repeater {
+ vdd18-supply = <&vreg_l15b_1p8>;
+ vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+&pmk8550_rtc {
+ status = "okay";
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&qup_i2c3_data_clk {
+ /* Use internal I2C pull-up */
+ bias-pull-up = <2200>;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8650/adsp.mbn",
+ "qcom/sm8650/adsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/sm8650/cdsp.mbn",
+ "qcom/sm8650/cdsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_mpss {
+ firmware-name = "qcom/sm8650/modem.mbn",
+ "qcom/sm8650/modem_dtb.mbn";
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>;
+
+ vmmc-supply = <&vreg_l9b_2p9>;
+ vqmmc-supply = <&vreg_l8b_1p8>;
+ bus-width = <4>;
+ no-sdio;
+ no-mmc;
+
+ pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
+ pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
+ pinctrl-names = "default", "sleep";
+
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&swr0 {
+ status = "okay";
+
+ /* WSA8845, Speaker North */
+ north_spkr: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ pinctrl-0 = <&spkr_1_sd_n_active>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&lpass_tlmm 21 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrLeft";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l3c_1p2>;
+ };
+
+ /* WSA8845, Speaker South */
+ south_spkr: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ pinctrl-0 = <&spkr_2_sd_n_active>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrRight";
+ vdd-1p8-supply = <&vreg_l15b_1p8>;
+ vdd-io-supply = <&vreg_l3c_1p2>;
+ };
+};
+
+&swr1 {
+ status = "okay";
+
+ /* WCD9395 RX */
+ wcd_rx: codec@0,4 {
+ compatible = "sdw20217010e00";
+ reg = <0 4>;
+
+ /*
+ * WCD9395 RX Port 1 (HPH_L/R) <=> SWR1 Port 1 (HPH_L/R)
+ * WCD9395 RX Port 2 (CLSH) <=> SWR1 Port 2 (CLSH)
+ * WCD9395 RX Port 3 (COMP_L/R) <=> SWR1 Port 3 (COMP_L/R)
+ * WCD9395 RX Port 4 (LO) <=> SWR1 Port 4 (LO)
+ * WCD9395 RX Port 5 (DSD_L/R) <=> SWR1 Port 5 (DSD_L/R)
+ * WCD9395 RX Port 6 (HIFI_PCM_L/R) <=> SWR1 Port 9 (HIFI_PCM_L/R)
+ */
+ qcom,rx-port-mapping = <1 2 3 4 5 9>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ /* WCD9395 TX */
+ wcd_tx: codec@0,3 {
+ compatible = "sdw20217010e00";
+ reg = <0 3>;
+
+ /*
+ * WCD9395 TX Port 1 (ADC1,2,3,4) <=> SWR2 Port 2 (TX SWR_INPUT 0,1,2,3)
+ * WCD9395 TX Port 2 (ADC3,4 & DMIC0,1) <=> SWR2 Port 2 (TX SWR_INPUT 0,1,2,3)
+ * WCD9395 TX Port 3 (DMIC0,1,2,3 & MBHC) <=> SWR2 Port 3 (TX SWR_INPUT 4,5,6,7)
+ * WCD9395 TX Port 4 (DMIC4,5,6,7) <=> SWR2 Port 4 (TX SWR_INPUT 8,9,10,11)
+ */
+ qcom,tx-port-mapping = <2 2 3 4>;
+ };
+};
+
+&tlmm {
+ /* Reserved I/Os for NFC */
+ gpio-reserved-ranges = <32 8>, <74 1>;
+
+ bt_default: bt-default-state {
+ bt-en-pins {
+ pins = "gpio17";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ sw-ctrl-pins {
+ pins = "gpio18";
+ function = "gpio";
+ bias-pull-down;
+ };
+ };
+
+ lt9611_irq_pin: lt9611-irq-state {
+ pins = "gpio85";
+ function = "gpio";
+ bias-disable;
+ };
+
+ lt9611_rst_pin: lt9611-rst-state {
+ pins = "gpio28";
+ function = "gpio";
+ output-high;
+ };
+
+ spkr_2_sd_n_active: spkr-2-sd-n-active-state {
+ pins = "gpio77";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ wcd_default: wcd-reset-n-active-state {
+ pins = "gpio107";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+
+ vddio-supply = <&vreg_l3c_1p2>;
+ vddaon-supply = <&vreg_l15b_1p8>;
+ vdddig-supply = <&vreg_s3c_0p9>;
+ vddrfa0p8-supply = <&vreg_s3c_0p9>;
+ vddrfa1p2-supply = <&vreg_s1c_1p2>;
+ vddrfa1p9-supply = <&vreg_s6c_1p8>;
+
+ max-speed = <3200000>;
+
+ enable-gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>;
+ swctrl-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&bt_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&uart15 {
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1c_1p2>;
+ vccq-max-microamp = <1200000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3i_1p2>;
+
+ status = "okay";
+};
+
+/*
+ * DPAUX -> WCD9395 -> USB_SBU -> USB-C
+ * eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> WCD9395 -> USB-C
+ * USB SS -> USB-C
+ */
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l1i_0p88>;
+ vdda12-supply = <&vreg_l3i_1p2>;
+
+ phys = <&pm8550b_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy {
+ vdda-phy-supply = <&vreg_l3i_1p2>;
+ vdda-pll-supply = <&vreg_l3g_0p91>;
+
+ orientation-switch;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy_dp_in {
+ remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_dp_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
+&xo_board {
+ clock-frequency = <76800000>;
+};

--
2.34.1

2024-04-22 11:50:53

by Rob Herring (Arm)

[permalink] [raw]

Subject: Re: [PATCH v4 0/3] arm64: qcom: sm8650: add support for the SM8650-HDK board

On Mon, 22 Apr 2024 10:48:11 +0200, Neil Armstrong wrote:
> The SM8650-HDK is an embedded development platforms for the
> Snapdragon 8 Gen 3 SoC aka SM8650, with the following features:
> - Qualcomm SM8650 SoC
> - 16GiB On-board LPDDR5
> - On-board WiFi 7 + Bluetooth 5.3/BLE
> - On-board UFS4.0
> - M.2 Key B+M Gen3x2 PCIe Slot
> - HDMI Output
> - USB-C Connector with DP Almode & Audio Accessory mode
> - Micro-SDCard Slot
> - Audio Jack with Playback and Microphone
> - 2 On-board Analog microphones
> - 2 On-board Speakers
> - 96Boards Compatible Low-Speed and High-Speed connectors [1]
> - For Camera, Sensors and external Display cards
> - Compatible with the Linaro Debug board [2]
> - SIM Slot for Modem
> - Debug connectors
> - 6x On-Board LEDs
>
> An optional Display Card kit can be connected on top,
> an overlay is handled to add support for the DSI Display
> and Touch Controller.
>
> Product Page: [3]
>
> Build Dependencies: None
>
> Functional Dependencies:
> - PCIe 1 PHY AUX Clock: https://lore.kernel.org/all/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-0-3ec0a966d52f@linaro.org/
> - PCI-MSI Fix: https://lore.kernel.org/all/[email protected]/
> - UCSI Fix: https://lore.kernel.org/all/[email protected]/
> - USB IRQs DT check fix: https://lore.kernel.org/all/20240314-topic-sm8650-upstream-usb-dt-irq-fix-v1-1-ea8ab2051869@linaro.org/
>
> [1] https://www.96boards.org/specifications/
> [2] https://git.codelinaro.org/linaro/qcomlt/debugboard
> [3] https://www.lantronix.com/products/snapdragon-8-gen-3-mobile-hardware-development-kit/
>
> Signed-off-by: Neil Armstrong <[email protected]>
> ---
> Changes in v4:
> - Rebased on next and fixed the apply failures
> - Link to v3: https://lore.kernel.org/r/[email protected]
>
> Changes in v3:
> - fixed regulator node name to fix ordering
> - deleted pcie_1_phy_aux clock
> - removed undeeded mdss_mdp status okay
> - collected revied & tested tags
> - Link to v2: https://lore.kernel.org/r/[email protected]
>
> Changes in v2:
> - Fixed commit messages with links, and recently added product page URL
> - Swapped i2c3/i2c6 nodes
> - Moved pcie_1_phy_aux_clk under pcie1_phy
> - Removed duplicate mdp_vsync pinctrl state
> - Collected review & tested tags
> - Link to v1: https://lore.kernel.org/r/[email protected]
>
> ---
> Neil Armstrong (3):
> dt-bindings: arm: qcom: Document the HDK8650 board
> arm64: dts: qcom: sm8650: add support for the SM8650-HDK board
> arch: arm64: dts: sm8650-hdk: add support for the Display Card overlay
>
> Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
> arch/arm64/boot/dts/qcom/Makefile | 5 +
> .../boot/dts/qcom/sm8650-hdk-display-card.dtso | 144 +++
> arch/arm64/boot/dts/qcom/sm8650-hdk.dts | 1251 ++++++++++++++++++++
> 4 files changed, 1401 insertions(+)
> ---
> base-commit: a8e1147ee205e7b8dfe18094ed39552a982857f1
> change-id: 20240223-topic-sm8650-upstream-hdk-e21cfd6f1de8
>
> Best regards,
> --
> Neil Armstrong <[email protected]>
>
>
>

My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

pip3 install dtschema --upgrade

New warnings running 'make CHECK_DTBS=y qcom/sm8650-hdk.dtb' for [email protected]:

arch/arm64/boot/dts/qcom/sm8650-hdk.dtb: pcie-1-phy-aux-clk: 'clock-frequency' is a required property
from schema $id: http://devicetree.org/schemas/clock/fixed-clock.yaml#
arch/arm64/boot/dts/qcom/sm8650-hdk.dtb: phy@1c0e000: clock-output-names: ['pcie1_pipe_clk'] is too short
from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml#
arch/arm64/boot/dts/qcom/sm8650-hdk.dtb: phy@1c0e000: #clock-cells:0:0: 1 was expected
from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml#

2024-04-22 16:05:17

by Neil Armstrong

[permalink] [raw]

Subject: Re: [PATCH v4 0/3] arm64: qcom: sm8650: add support for the SM8650-HDK board

On 22/04/2024 13:50, Rob Herring wrote:
>
> On Mon, 22 Apr 2024 10:48:11 +0200, Neil Armstrong wrote:
>> The SM8650-HDK is an embedded development platforms for the
>> Snapdragon 8 Gen 3 SoC aka SM8650, with the following features:
>> - Qualcomm SM8650 SoC
>> - 16GiB On-board LPDDR5
>> - On-board WiFi 7 + Bluetooth 5.3/BLE
>> - On-board UFS4.0
>> - M.2 Key B+M Gen3x2 PCIe Slot
>> - HDMI Output
>> - USB-C Connector with DP Almode & Audio Accessory mode
>> - Micro-SDCard Slot
>> - Audio Jack with Playback and Microphone
>> - 2 On-board Analog microphones
>> - 2 On-board Speakers
>> - 96Boards Compatible Low-Speed and High-Speed connectors [1]
>> - For Camera, Sensors and external Display cards
>> - Compatible with the Linaro Debug board [2]
>> - SIM Slot for Modem
>> - Debug connectors
>> - 6x On-Board LEDs
>>
>> An optional Display Card kit can be connected on top,
>> an overlay is handled to add support for the DSI Display
>> and Touch Controller.
>>
>> Product Page: [3]
>>
>> Build Dependencies: None
>>
>> Functional Dependencies:
>> - PCIe 1 PHY AUX Clock: https://lore.kernel.org/all/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-0-3ec0a966d52f@linaro.org/
>> - PCI-MSI Fix: https://lore.kernel.org/all/[email protected]/
>> - UCSI Fix: https://lore.kernel.org/all/[email protected]/
>> - USB IRQs DT check fix: https://lore.kernel.org/all/20240314-topic-sm8650-upstream-usb-dt-irq-fix-v1-1-ea8ab2051869@linaro.org/
>>
>> [1] https://www.96boards.org/specifications/
>> [2] https://git.codelinaro.org/linaro/qcomlt/debugboard
>> [3] https://www.lantronix.com/products/snapdragon-8-gen-3-mobile-hardware-development-kit/
>>
>> Signed-off-by: Neil Armstrong <[email protected]>
>> ---
>> Changes in v4:
>> - Rebased on next and fixed the apply failures
>> - Link to v3: https://lore.kernel.org/r/[email protected]
>>
>> Changes in v3:
>> - fixed regulator node name to fix ordering
>> - deleted pcie_1_phy_aux clock
>> - removed undeeded mdss_mdp status okay
>> - collected revied & tested tags
>> - Link to v2: https://lore.kernel.org/r/[email protected]
>>
>> Changes in v2:
>> - Fixed commit messages with links, and recently added product page URL
>> - Swapped i2c3/i2c6 nodes
>> - Moved pcie_1_phy_aux_clk under pcie1_phy
>> - Removed duplicate mdp_vsync pinctrl state
>> - Collected review & tested tags
>> - Link to v1: https://lore.kernel.org/r/[email protected]
>>
>> ---
>> Neil Armstrong (3):
>> dt-bindings: arm: qcom: Document the HDK8650 board
>> arm64: dts: qcom: sm8650: add support for the SM8650-HDK board
>> arch: arm64: dts: sm8650-hdk: add support for the Display Card overlay
>>
>> Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>> arch/arm64/boot/dts/qcom/Makefile | 5 +
>> .../boot/dts/qcom/sm8650-hdk-display-card.dtso | 144 +++
>> arch/arm64/boot/dts/qcom/sm8650-hdk.dts | 1251 ++++++++++++++++++++
>> 4 files changed, 1401 insertions(+)
>> ---
>> base-commit: a8e1147ee205e7b8dfe18094ed39552a982857f1
>> change-id: 20240223-topic-sm8650-upstream-hdk-e21cfd6f1de8
>>
>> Best regards,
>> --
>> Neil Armstrong <[email protected]>
>>
>>
>>
>
>
> My bot found new DTB warnings on the .dts files added or changed in this
> series.
>
> Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
> are fixed by another series. Ultimately, it is up to the platform
> maintainer whether these warnings are acceptable or not. No need to reply
> unless the platform maintainer has comments.
>
> If you already ran DT checks and didn't see these error(s), then
> make sure dt-schema is up to date:
>
> pip3 install dtschema --upgrade
>
>
> New warnings running 'make CHECK_DTBS=y qcom/sm8650-hdk.dtb' for [email protected]:
>
> arch/arm64/boot/dts/qcom/sm8650-hdk.dtb: pcie-1-phy-aux-clk: 'clock-frequency' is a required property
> from schema $id: http://devicetree.org/schemas/clock/fixed-clock.yaml#
> arch/arm64/boot/dts/qcom/sm8650-hdk.dtb: phy@1c0e000: clock-output-names: ['pcie1_pipe_clk'] is too short
> from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml#
> arch/arm64/boot/dts/qcom/sm8650-hdk.dtb: phy@1c0e000: #clock-cells:0:0: 1 was expected
> from schema $id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml#

Thx, this is fixed by https://lore.kernel.org/all/20240422-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v3-0-799475a27cce@linaro.org/

Neil

>
>
>
>
>