Set I3C config in yosemite4 DTS.
Test plan:
Tested with aspeed I3C patches and I3C hub driver.
Signed-off-by: Delphine CC Chiu <[email protected]>
---
.../aspeed/aspeed-bmc-facebook-yosemite4.dts | 86 +++++++++++++++++++
1 file changed, 86 insertions(+)
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 64075cc41d92..6a30c424d745 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -595,6 +595,92 @@ i2c-mux@72 {
};
};
+&i3c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i3c1_default>;
+ i3c-pp-scl-hi-period-ns = <40>;
+ i3c-pp-scl-lo-period-ns = <40>;
+ i3c-od-scl-hi-period-ns = <380>;
+ i3c-od-scl-lo-period-ns = <620>;
+ sda-tx-hold-ns = <10>;
+
+ mctp-controller;
+ hub@0x70 {
+ reg = <0x70 0x3c0 0x00700000>;
+ cp0-ldo-en = "enabled";
+ cp1-ldo-en = "enabled";
+ cp0-ldo-volt = "1.2V";
+ cp1-ldo-volt = "1.2V";
+ tp0145-ldo-en = "enabled";
+ tp2367-ldo-en = "enabled";
+ tp0145-ldo-volt = "1.2V";
+ tp2367-ldo-volt = "1.2V";
+ tp0145-pullup = "2k";
+ tp2367-pullup = "2k";
+
+ target-port@0 {
+ mode = "i3c";
+ pullup = "enabled";
+ };
+ target-port@1 {
+ mode = "i3c";
+ pullup = "enabled";
+ };
+ target-port@2 {
+ mode = "i3c";
+ pullup = "enabled";
+ };
+ target-port@3 {
+ mode = "i3c";
+ pullup = "enabled";
+ };
+ };
+};
+
+&i3c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i3c2_default>;
+ i3c-pp-scl-hi-period-ns = <40>;
+ i3c-pp-scl-lo-period-ns = <40>;
+ i3c-od-scl-hi-period-ns = <380>;
+ i3c-od-scl-lo-period-ns = <620>;
+ sda-tx-hold-ns = <10>;
+
+ mctp-controller;
+ hub@0x70 {
+ reg = <0x70 0x3c0 0x00700000>;
+ cp0-ldo-en = "enabled";
+ cp1-ldo-en = "enabled";
+ cp0-ldo-volt = "1.2V";
+ cp1-ldo-volt = "1.2V";
+ tp0145-ldo-en = "enabled";
+ tp2367-ldo-en = "enabled";
+ tp0145-ldo-volt = "1.2V";
+ tp2367-ldo-volt = "1.2V";
+ tp0145-pullup = "2k";
+ tp2367-pullup = "2k";
+
+ target-port@0 {
+ mode = "i3c";
+ pullup = "enabled";
+ };
+ target-port@1 {
+ mode = "i3c";
+ pullup = "enabled";
+ };
+ target-port@2 {
+ mode = "i3c";
+ pullup = "enabled";
+ };
+ target-port@3 {
+ mode = "i3c";
+ pullup = "enabled";
+ };
+ };
+};
+
&adc0 {
ref_voltage = <2500>;
status = "okay";
--
2.25.1
On 06/05/2024 13:33, Delphine CC Chiu wrote:
> Set I3C config in yosemite4 DTS.
>
> Test plan:
> Tested with aspeed I3C patches and I3C hub driver.
>
> Signed-off-by: Delphine CC Chiu <[email protected]>
> ---
> .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 86 +++++++++++++++++++
> 1 file changed, 86 insertions(+)
>
> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> index 64075cc41d92..6a30c424d745 100644
> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
> @@ -595,6 +595,92 @@ i2c-mux@72 {
> };
> };
>
> +&i3c0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i3c1_default>;
> + i3c-pp-scl-hi-period-ns = <40>;
> + i3c-pp-scl-lo-period-ns = <40>;
> + i3c-od-scl-hi-period-ns = <380>;
> + i3c-od-scl-lo-period-ns = <620>;
> + sda-tx-hold-ns = <10>;
> +
> + mctp-controller;
> + hub@0x70 {
That's not a valid unit address.
> + reg = <0x70 0x3c0 0x00700000>;
> + cp0-ldo-en = "enabled";
> + cp1-ldo-en = "enabled";
> + cp0-ldo-volt = "1.2V";
> + cp1-ldo-volt = "1.2V";
> + tp0145-ldo-en = "enabled";
> + tp2367-ldo-en = "enabled";
> + tp0145-ldo-volt = "1.2V";
> + tp2367-ldo-volt = "1.2V";
> + tp0145-pullup = "2k";
> + tp2367-pullup = "2k";
Where are bindings for all this?
Best regards,
Krzysztof
Hi Delphine,
kernel test robot noticed the following build errors:
[auto build test ERROR on robh/for-next]
[also build test ERROR on linus/master v6.9-rc7 next-20240507]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Delphine-CC-Chiu/ARM-dts-aspeed-yosemite4-add-I3C-config-in-DTS/20240506-193458
base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
patch link: https://lore.kernel.org/r/20240506113306.1283179-1-Delphine_CC_Chiu%40wiwynn.com
patch subject: [PATCH v1] ARM: dts: aspeed: yosemite4: add I3C config in DTS
config: arm-multi_v5_defconfig (https://download.01.org/0day-ci/archive/20240507/[email protected]/config)
compiler: arm-linux-gnueabi-gcc (GCC) 13.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240507/[email protected]/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
All errors (new ones prefixed by >>):
>> Error: arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts:598.1-6 Label or path i3c0 not found
>> Error: arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts:641.1-6 Label or path i3c1 not found
FATAL ERROR: Syntax error parsing input tree
--
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki