The GSBUSCFG0 register bits [31:16] are used to configure the cache type
settings of the descriptor and data write/read transfers (Cacheable,
Bufferable/Posted). When CCI is enabled in the design, DWC3 core GSBUSCFG0
cache bits must be updated to support CCI enabled transfers in USB.
To program GSBUSCFG0 cache bits create a software node property
in AMD-xilinx dwc3 glue driver and pass it to dwc3 core. The core
then reads this property value and configures it in dwc3_core_init()
sequence.
Signed-off-by: Radhey Shyam Pandey <[email protected]>
---
Changes for v3:
In v2 review as suggested by Thinh Nguyen, switch to swnode implementation
for passing GSBUSCFG0 cache bits from AMD-xilinx dwc3 glue driver to
core driver.
Changes for v2:
Make GSBUSCFG0 configuration specific to AMD-xilinx platform.
Taken reference from existing commit ec5eb43813a4 ("usb: dwc3: core:
add support for realtek SoCs custom's global register start address")
v1 link:
https://lore.kernel.org/all/[email protected]
---
drivers/usb/dwc3/core.c | 24 ++++++++++++++++++++++++
drivers/usb/dwc3/core.h | 8 ++++++++
drivers/usb/dwc3/dwc3-xilinx.c | 18 +++++++++++++++++-
3 files changed, 49 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 7ee61a89520b..159d21b25629 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -23,6 +23,7 @@
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/of.h>
+#include <linux/of_address.h>
#include <linux/of_graph.h>
#include <linux/acpi.h>
#include <linux/pinctrl/consumer.h>
@@ -599,6 +600,19 @@ static void dwc3_cache_hwparams(struct dwc3 *dwc)
parms->hwparams9 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS9);
}
+static void dwc3_config_soc_bus(struct dwc3 *dwc)
+{
+ if (of_dma_is_coherent(dwc->dev->of_node)) {
+ u32 reg;
+
+ reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
+ reg &= ~DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK;
+ reg |= (dwc->acache_data_rd_wr_info <<
+ DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT);
+ dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg);
+ }
+}
+
static int dwc3_core_ulpi_init(struct dwc3 *dwc)
{
int intf;
@@ -1320,6 +1334,8 @@ static int dwc3_core_init(struct dwc3 *dwc)
dwc3_set_incr_burst_type(dwc);
+ dwc3_config_soc_bus(dwc);
+
ret = dwc3_phy_power_on(dwc);
if (ret)
goto err_exit_phy;
@@ -1574,6 +1590,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
u8 tx_max_burst_prd = 0;
u8 tx_fifo_resize_max_num;
const char *usb_psy_name;
+ struct device *tmpdev;
int ret;
/* default to highest possible threshold */
@@ -1716,6 +1733,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
dwc->dis_split_quirk = device_property_read_bool(dev,
"snps,dis-split-quirk");
+ /* Iterate over all parent nodes for finding swnode properties */
+ for (tmpdev = dwc->dev; tmpdev; tmpdev = tmpdev->parent) {
+ device_property_read_u16(tmpdev,
+ "snps,acache-data-rd-wr-info",
+ &dwc->acache_data_rd_wr_info);
+ }
+
dwc->lpm_nyet_threshold = lpm_nyet_threshold;
dwc->tx_de_emphasis = tx_de_emphasis;
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 3781c736c1a1..57b3cb739353 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -194,6 +194,10 @@
#define DWC3_GSBUSCFG0_INCRBRSTENA (1 << 0) /* undefined length enable */
#define DWC3_GSBUSCFG0_INCRBRST_MASK 0xff
+/* Global SoC Bus Configuration Register: AHB-prot/AXI-cache/OCP-ReqInfo */
+#define DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK GENMASK(31, 16)
+#define DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT 16
+
/* Global Debug LSP MUX Select */
#define DWC3_GDBGLSPMUX_ENDBC BIT(15) /* Host only */
#define DWC3_GDBGLSPMUX_HOSTSELECT(n) ((n) & 0x3fff)
@@ -1153,6 +1157,9 @@ struct dwc3_scratchpad_array {
* @num_ep_resized: carries the current number endpoints which have had its tx
* fifo resized.
* @debug_root: root debugfs directory for this device to put its files in.
+ * @acache_data_rd_wr_info: store GSBUSCFG0.DATRDREQINFO, DESRDREQINFO,
+ * DATWRREQINFO, and DESWRREQINFO value passed from
+ * glue driver.
*/
struct dwc3 {
struct work_struct drd_work;
@@ -1380,6 +1387,7 @@ struct dwc3 {
int last_fifo_depth;
int num_ep_resized;
struct dentry *debug_root;
+ u16 acache_data_rd_wr_info;
};
#define INCRX_BURST_MODE 0
diff --git a/drivers/usb/dwc3/dwc3-xilinx.c b/drivers/usb/dwc3/dwc3-xilinx.c
index 6095f4dee6ce..f3757bfbd650 100644
--- a/drivers/usb/dwc3/dwc3-xilinx.c
+++ b/drivers/usb/dwc3/dwc3-xilinx.c
@@ -47,6 +47,15 @@ struct dwc3_xlnx {
struct phy *usb3_phy;
};
+static const struct property_entry dwc3_xilinx_properties[] = {
+ PROPERTY_ENTRY_U16("snps,acache-data-rd-wr-info", 0xffff),
+ {},
+};
+
+static const struct software_node dwc3_xilinx_swnode = {
+ .properties = dwc3_xilinx_properties,
+};
+
static void dwc3_xlnx_mask_phy_rst(struct dwc3_xlnx *priv_data, bool mask)
{
u32 reg;
@@ -288,10 +297,14 @@ static int dwc3_xlnx_probe(struct platform_device *pdev)
if (ret)
goto err_clk_put;
- ret = of_platform_populate(np, NULL, NULL, dev);
+ ret = device_add_software_node(dev, &dwc3_xilinx_swnode);
if (ret)
goto err_clk_put;
+ ret = of_platform_populate(np, NULL, NULL, dev);
+ if (ret)
+ goto err_remove_swnode;
+
pm_runtime_set_active(dev);
ret = devm_pm_runtime_enable(dev);
if (ret < 0)
@@ -303,6 +316,9 @@ static int dwc3_xlnx_probe(struct platform_device *pdev)
err_pm_set_suspended:
pm_runtime_set_suspended(dev);
+err_remove_swnode:
+ device_remove_software_node(dev);
+
err_clk_put:
clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data->clks);
--
2.34.1
On 06/06/2024 09:01, Radhey Shyam Pandey wrote:
> The GSBUSCFG0 register bits [31:16] are used to configure the cache type
> settings of the descriptor and data write/read transfers (Cacheable,
> Bufferable/Posted). When CCI is enabled in the design, DWC3 core GSBUSCFG0
> cache bits must be updated to support CCI enabled transfers in USB.
>
> To program GSBUSCFG0 cache bits create a software node property
> in AMD-xilinx dwc3 glue driver and pass it to dwc3 core. The core
> then reads this property value and configures it in dwc3_core_init()
> sequence.
>
> Signed-off-by: Radhey Shyam Pandey <[email protected]>
> ---
> Changes for v3:
> In v2 review as suggested by Thinh Nguyen, switch to swnode implementation
> for passing GSBUSCFG0 cache bits from AMD-xilinx dwc3 glue driver to
> core driver.
>
> Changes for v2:
> Make GSBUSCFG0 configuration specific to AMD-xilinx platform.
> Taken reference from existing commit ec5eb43813a4 ("usb: dwc3: core:
> add support for realtek SoCs custom's global register start address")
>
> v1 link:
> https://lore.kernel.org/all/[email protected]
> ---
> drivers/usb/dwc3/core.c | 24 ++++++++++++++++++++++++
> drivers/usb/dwc3/core.h | 8 ++++++++
> drivers/usb/dwc3/dwc3-xilinx.c | 18 +++++++++++++++++-
> 3 files changed, 49 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index 7ee61a89520b..159d21b25629 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -23,6 +23,7 @@
> #include <linux/delay.h>
> #include <linux/dma-mapping.h>
> #include <linux/of.h>
> +#include <linux/of_address.h>
> #include <linux/of_graph.h>
> #include <linux/acpi.h>
> #include <linux/pinctrl/consumer.h>
> @@ -599,6 +600,19 @@ static void dwc3_cache_hwparams(struct dwc3 *dwc)
> parms->hwparams9 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS9);
> }
>
> +static void dwc3_config_soc_bus(struct dwc3 *dwc)
> +{
> + if (of_dma_is_coherent(dwc->dev->of_node)) {
> + u32 reg;
> +
> + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
> + reg &= ~DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK;
> + reg |= (dwc->acache_data_rd_wr_info <<
> + DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT);
> + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg);
> + }
> +}
> +
> static int dwc3_core_ulpi_init(struct dwc3 *dwc)
> {
> int intf;
> @@ -1320,6 +1334,8 @@ static int dwc3_core_init(struct dwc3 *dwc)
>
> dwc3_set_incr_burst_type(dwc);
>
> + dwc3_config_soc_bus(dwc);
> +
> ret = dwc3_phy_power_on(dwc);
> if (ret)
> goto err_exit_phy;
> @@ -1574,6 +1590,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
> u8 tx_max_burst_prd = 0;
> u8 tx_fifo_resize_max_num;
> const char *usb_psy_name;
> + struct device *tmpdev;
> int ret;
>
> /* default to highest possible threshold */
> @@ -1716,6 +1733,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
> dwc->dis_split_quirk = device_property_read_bool(dev,
> "snps,dis-split-quirk");
>
> + /* Iterate over all parent nodes for finding swnode properties */
And:
/* non-DT (non-ABI) properties */
so someone will not try to make it ABI post-factum.
Best regards,
Krzysztof
Hi,
On Thu, Jun 06, 2024, Radhey Shyam Pandey wrote:
> The GSBUSCFG0 register bits [31:16] are used to configure the cache type
> settings of the descriptor and data write/read transfers (Cacheable,
> Bufferable/Posted). When CCI is enabled in the design, DWC3 core GSBUSCFG0
> cache bits must be updated to support CCI enabled transfers in USB.
>
> To program GSBUSCFG0 cache bits create a software node property
> in AMD-xilinx dwc3 glue driver and pass it to dwc3 core. The core
> then reads this property value and configures it in dwc3_core_init()
> sequence.
>
> Signed-off-by: Radhey Shyam Pandey <[email protected]>
> ---
> Changes for v3:
> In v2 review as suggested by Thinh Nguyen, switch to swnode implementation
> for passing GSBUSCFG0 cache bits from AMD-xilinx dwc3 glue driver to
> core driver.
>
> Changes for v2:
> Make GSBUSCFG0 configuration specific to AMD-xilinx platform.
> Taken reference from existing commit ec5eb43813a4 ("usb: dwc3: core:
> add support for realtek SoCs custom's global register start address")
>
> v1 link:
> https://urldefense.com/v3/__https://lore.kernel.org/all/[email protected]__;!!A4F2R9G_pg!cOoWxmacxPeYVCxDfg3-xlQLhKm8MIEgwWx45cLQjgwRWA4e4QyY_kGVVHo2m_dcRbpBQEFpB9JsYP6nzasK2AIAsyefjQ$
> ---
> drivers/usb/dwc3/core.c | 24 ++++++++++++++++++++++++
> drivers/usb/dwc3/core.h | 8 ++++++++
> drivers/usb/dwc3/dwc3-xilinx.c | 18 +++++++++++++++++-
> 3 files changed, 49 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index 7ee61a89520b..159d21b25629 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -23,6 +23,7 @@
> #include <linux/delay.h>
> #include <linux/dma-mapping.h>
> #include <linux/of.h>
> +#include <linux/of_address.h>
> #include <linux/of_graph.h>
> #include <linux/acpi.h>
> #include <linux/pinctrl/consumer.h>
> @@ -599,6 +600,19 @@ static void dwc3_cache_hwparams(struct dwc3 *dwc)
> parms->hwparams9 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS9);
> }
>
> +static void dwc3_config_soc_bus(struct dwc3 *dwc)
> +{
> + if (of_dma_is_coherent(dwc->dev->of_node)) {
This can be applicable outside of of_node, do we need this if case?
> + u32 reg;
> +
> + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
> + reg &= ~DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK;
> + reg |= (dwc->acache_data_rd_wr_info <<
What if the user doesn't specify this property? We should not
automatically write 0 by default.
> + DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT);
> + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg);
> + }
> +}
> +
> static int dwc3_core_ulpi_init(struct dwc3 *dwc)
> {
> int intf;
> @@ -1320,6 +1334,8 @@ static int dwc3_core_init(struct dwc3 *dwc)
>
> dwc3_set_incr_burst_type(dwc);
>
> + dwc3_config_soc_bus(dwc);
> +
> ret = dwc3_phy_power_on(dwc);
> if (ret)
> goto err_exit_phy;
> @@ -1574,6 +1590,7 @@ static void dwc3_get_properties(struct dwc3 *dwc)
> u8 tx_max_burst_prd = 0;
> u8 tx_fifo_resize_max_num;
> const char *usb_psy_name;
> + struct device *tmpdev;
> int ret;
>
> /* default to highest possible threshold */
> @@ -1716,6 +1733,13 @@ static void dwc3_get_properties(struct dwc3 *dwc)
> dwc->dis_split_quirk = device_property_read_bool(dev,
> "snps,dis-split-quirk");
>
> + /* Iterate over all parent nodes for finding swnode properties */
> + for (tmpdev = dwc->dev; tmpdev; tmpdev = tmpdev->parent) {
> + device_property_read_u16(tmpdev,
> + "snps,acache-data-rd-wr-info",
> + &dwc->acache_data_rd_wr_info);
> + }
> +
Please split this to a separate function and name it as
dwc3_get_software_properties(). For now, just the new property you
create is fine. We can introduce new patches to move all the software
defined properties (ie. non ABI/DS) there such as sysdev_is_parent.
> dwc->lpm_nyet_threshold = lpm_nyet_threshold;
> dwc->tx_de_emphasis = tx_de_emphasis;
>
> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> index 3781c736c1a1..57b3cb739353 100644
> --- a/drivers/usb/dwc3/core.h
> +++ b/drivers/usb/dwc3/core.h
> @@ -194,6 +194,10 @@
> #define DWC3_GSBUSCFG0_INCRBRSTENA (1 << 0) /* undefined length enable */
> #define DWC3_GSBUSCFG0_INCRBRST_MASK 0xff
>
> +/* Global SoC Bus Configuration Register: AHB-prot/AXI-cache/OCP-ReqInfo */
> +#define DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK GENMASK(31, 16)
Can we rename this to DWC3_GSBUSCFG0_REQINFO_MASK
> +#define DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT 16
We don't need a shift value. Either define DWC3_GSBUSCFG0_REQINFO(n) or
use FIELD_PREP and the mask.
> +
> /* Global Debug LSP MUX Select */
> #define DWC3_GDBGLSPMUX_ENDBC BIT(15) /* Host only */
> #define DWC3_GDBGLSPMUX_HOSTSELECT(n) ((n) & 0x3fff)
> @@ -1153,6 +1157,9 @@ struct dwc3_scratchpad_array {
> * @num_ep_resized: carries the current number endpoints which have had its tx
> * fifo resized.
> * @debug_root: root debugfs directory for this device to put its files in.
> + * @acache_data_rd_wr_info: store GSBUSCFG0.DATRDREQINFO, DESRDREQINFO,
> + * DATWRREQINFO, and DESWRREQINFO value passed from
> + * glue driver.
> */
> struct dwc3 {
> struct work_struct drd_work;
> @@ -1380,6 +1387,7 @@ struct dwc3 {
> int last_fifo_depth;
> int num_ep_resized;
> struct dentry *debug_root;
> + u16 acache_data_rd_wr_info;
If we do need to keep this field around, please define the default
for unspecified value. Also rename this to gsbuscfg0_reqinfo.
> };
>
> #define INCRX_BURST_MODE 0
> diff --git a/drivers/usb/dwc3/dwc3-xilinx.c b/drivers/usb/dwc3/dwc3-xilinx.c
> index 6095f4dee6ce..f3757bfbd650 100644
> --- a/drivers/usb/dwc3/dwc3-xilinx.c
> +++ b/drivers/usb/dwc3/dwc3-xilinx.c
> @@ -47,6 +47,15 @@ struct dwc3_xlnx {
> struct phy *usb3_phy;
> };
>
> +static const struct property_entry dwc3_xilinx_properties[] = {
> + PROPERTY_ENTRY_U16("snps,acache-data-rd-wr-info", 0xffff),
> + {},
> +};
> +
> +static const struct software_node dwc3_xilinx_swnode = {
> + .properties = dwc3_xilinx_properties,
> +};
> +
> static void dwc3_xlnx_mask_phy_rst(struct dwc3_xlnx *priv_data, bool mask)
> {
> u32 reg;
> @@ -288,10 +297,14 @@ static int dwc3_xlnx_probe(struct platform_device *pdev)
> if (ret)
> goto err_clk_put;
>
> - ret = of_platform_populate(np, NULL, NULL, dev);
> + ret = device_add_software_node(dev, &dwc3_xilinx_swnode);
> if (ret)
> goto err_clk_put;
>
> + ret = of_platform_populate(np, NULL, NULL, dev);
> + if (ret)
> + goto err_remove_swnode;
> +
> pm_runtime_set_active(dev);
> ret = devm_pm_runtime_enable(dev);
> if (ret < 0)
> @@ -303,6 +316,9 @@ static int dwc3_xlnx_probe(struct platform_device *pdev)
> err_pm_set_suspended:
> pm_runtime_set_suspended(dev);
>
> +err_remove_swnode:
> + device_remove_software_node(dev);
> +
> err_clk_put:
> clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data->clks);
>
> --
> 2.34.1
>
Thanks,
Thinh
> -----Original Message-----
> From: Thinh Nguyen <[email protected]>
> Sent: Saturday, June 8, 2024 5:39 AM
> To: Pandey, Radhey Shyam <[email protected]>
> Cc: Thinh Nguyen <[email protected]>;
> [email protected]; Simek, Michal <[email protected]>;
> [email protected]; [email protected]; linux-
> [email protected]; [email protected]; linux-arm-
> [email protected]; git (AMD-Xilinx) <[email protected]>
> Subject: Re: [PATCH v3] usb: dwc3: enable CCI support for AMD-xilinx DWC3
> controller
>
> Hi,
>
> On Thu, Jun 06, 2024, Radhey Shyam Pandey wrote:
> > The GSBUSCFG0 register bits [31:16] are used to configure the cache type
> > settings of the descriptor and data write/read transfers (Cacheable,
> > Bufferable/Posted). When CCI is enabled in the design, DWC3 core
> GSBUSCFG0
> > cache bits must be updated to support CCI enabled transfers in USB.
> >
> > To program GSBUSCFG0 cache bits create a software node property
> > in AMD-xilinx dwc3 glue driver and pass it to dwc3 core. The core
> > then reads this property value and configures it in dwc3_core_init()
> > sequence.
> >
> > Signed-off-by: Radhey Shyam Pandey <[email protected]>
> > ---
> > Changes for v3:
> > In v2 review as suggested by Thinh Nguyen, switch to swnode
> implementation
> > for passing GSBUSCFG0 cache bits from AMD-xilinx dwc3 glue driver to
> > core driver.
> >
> > Changes for v2:
> > Make GSBUSCFG0 configuration specific to AMD-xilinx platform.
> > Taken reference from existing commit ec5eb43813a4 ("usb: dwc3: core:
> > add support for realtek SoCs custom's global register start address")
> >
> > v1 link:
> >
> https://urldefense.com/v3/__https://lore.kernel.org/all/20231013053448.11
> [email protected]__;!!A4F2R9G_pg!cOoWxmacxPeYVCxDfg3-
> xlQLhKm8MIEgwWx45cLQjgwRWA4e4QyY_kGVVHo2m_dcRbpBQEFpB9JsYP6
> nzasK2AIAsyefjQ$
> > ---
> > drivers/usb/dwc3/core.c | 24 ++++++++++++++++++++++++
> > drivers/usb/dwc3/core.h | 8 ++++++++
> > drivers/usb/dwc3/dwc3-xilinx.c | 18 +++++++++++++++++-
> > 3 files changed, 49 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> > index 7ee61a89520b..159d21b25629 100644
> > --- a/drivers/usb/dwc3/core.c
> > +++ b/drivers/usb/dwc3/core.c
> > @@ -23,6 +23,7 @@
> > #include <linux/delay.h>
> > #include <linux/dma-mapping.h>
> > #include <linux/of.h>
> > +#include <linux/of_address.h>
> > #include <linux/of_graph.h>
> > #include <linux/acpi.h>
> > #include <linux/pinctrl/consumer.h>
> > @@ -599,6 +600,19 @@ static void dwc3_cache_hwparams(struct dwc3
> *dwc)
> > parms->hwparams9 = dwc3_readl(dwc->regs,
> DWC3_GHWPARAMS9);
> > }
> >
> > +static void dwc3_config_soc_bus(struct dwc3 *dwc)
> > +{
> > + if (of_dma_is_coherent(dwc->dev->of_node)) {
>
> This can be applicable outside of of_node, do we need this if case?
This of_dma_is_coherent detect presence of dma-coherent property
in dwc3 node and then if propery is present we program
GSBUSCFG0_REQINFO.
Alternatively glue driver can also read/detect DWC3 node dma-coherent
property and then override snps,acache-data-rd-wr-info value only
if dma-coherent property is present.
Or do you mean we should support presence of dma-coherent
property in either parent node ("xlnx,zynqmp-dwc3") or child
node(snps,dwc3)?
>
> > + u32 reg;
> > +
> > + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
> > + reg &=
> ~DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK;
> > + reg |= (dwc->acache_data_rd_wr_info <<
>
> What if the user doesn't specify this property? We should not
> automatically write 0 by default.
USB3 3.30a core configured for 2.0 I see reset value for
GSBUSCFG0 [31:16] bits are 0. Will cross-check it for other
versions.
>
> > +
> DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT);
> > + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg);
> > + }
> > +}
> > +
> > static int dwc3_core_ulpi_init(struct dwc3 *dwc)
> > {
> > int intf;
> > @@ -1320,6 +1334,8 @@ static int dwc3_core_init(struct dwc3 *dwc)
> >
> > dwc3_set_incr_burst_type(dwc);
> >
> > + dwc3_config_soc_bus(dwc);
> > +
> > ret = dwc3_phy_power_on(dwc);
> > if (ret)
> > goto err_exit_phy;
> > @@ -1574,6 +1590,7 @@ static void dwc3_get_properties(struct dwc3
> *dwc)
> > u8 tx_max_burst_prd = 0;
> > u8 tx_fifo_resize_max_num;
> > const char *usb_psy_name;
> > + struct device *tmpdev;
> > int ret;
> >
> > /* default to highest possible threshold */
> > @@ -1716,6 +1733,13 @@ static void dwc3_get_properties(struct dwc3
> *dwc)
> > dwc->dis_split_quirk = device_property_read_bool(dev,
> > "snps,dis-split-quirk");
> >
> > + /* Iterate over all parent nodes for finding swnode properties */
> > + for (tmpdev = dwc->dev; tmpdev; tmpdev = tmpdev->parent) {
> > + device_property_read_u16(tmpdev,
> > + "snps,acache-data-rd-wr-info",
> > + &dwc->acache_data_rd_wr_info);
> > + }
> > +
>
> Please split this to a separate function and name it as
> dwc3_get_software_properties(). For now, just the new property you
> create is fine. We can introduce new patches to move all the software
> defined properties (ie. non ABI/DS) there such as sysdev_is_parent.
Sure , will split it to separate patch.
>
> > dwc->lpm_nyet_threshold = lpm_nyet_threshold;
> > dwc->tx_de_emphasis = tx_de_emphasis;
> >
> > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> > index 3781c736c1a1..57b3cb739353 100644
> > --- a/drivers/usb/dwc3/core.h
> > +++ b/drivers/usb/dwc3/core.h
> > @@ -194,6 +194,10 @@
> > #define DWC3_GSBUSCFG0_INCRBRSTENA (1 << 0) /* undefined length
> enable */
> > #define DWC3_GSBUSCFG0_INCRBRST_MASK 0xff
> >
> > +/* Global SoC Bus Configuration Register: AHB-prot/AXI-cache/OCP-
> ReqInfo */
> > +#define DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK
> GENMASK(31, 16)
>
> Can we rename this to DWC3_GSBUSCFG0_REQINFO_MASK
Yes, will do it in next version.
>
> > +#define DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT 16
>
> We don't need a shift value. Either define DWC3_GSBUSCFG0_REQINFO(n) or
> use FIELD_PREP and the mask.
Yes, will fix it in next version.
>
> > +
> > /* Global Debug LSP MUX Select */
> > #define DWC3_GDBGLSPMUX_ENDBC BIT(15) /* Host only
> */
> > #define DWC3_GDBGLSPMUX_HOSTSELECT(n) ((n) & 0x3fff)
> > @@ -1153,6 +1157,9 @@ struct dwc3_scratchpad_array {
> > * @num_ep_resized: carries the current number endpoints which have
> had its tx
> > * fifo resized.
> > * @debug_root: root debugfs directory for this device to put its files in.
> > + * @acache_data_rd_wr_info: store GSBUSCFG0.DATRDREQINFO,
> DESRDREQINFO,
> > + * DATWRREQINFO, and DESWRREQINFO value passed from
> > + * glue driver.
> > */
> > struct dwc3 {
> > struct work_struct drd_work;
> > @@ -1380,6 +1387,7 @@ struct dwc3 {
> > int last_fifo_depth;
> > int num_ep_resized;
> > struct dentry *debug_root;
> > + u16 acache_data_rd_wr_info;
>
> If we do need to keep this field around, please define the default
> for unspecified value. Also rename this to gsbuscfg0_reqinfo.
Sure. will define default (likely 0 ) and rename it to gsbuscfg0_reqinfo
in next version.
>
> > };
> >
> > #define INCRX_BURST_MODE 0
> > diff --git a/drivers/usb/dwc3/dwc3-xilinx.c b/drivers/usb/dwc3/dwc3-
> xilinx.c
> > index 6095f4dee6ce..f3757bfbd650 100644
> > --- a/drivers/usb/dwc3/dwc3-xilinx.c
> > +++ b/drivers/usb/dwc3/dwc3-xilinx.c
> > @@ -47,6 +47,15 @@ struct dwc3_xlnx {
> > struct phy *usb3_phy;
> > };
> >
> > +static const struct property_entry dwc3_xilinx_properties[] = {
> > + PROPERTY_ENTRY_U16("snps,acache-data-rd-wr-info", 0xffff),
> > + {},
> > +};
> > +
> > +static const struct software_node dwc3_xilinx_swnode = {
> > + .properties = dwc3_xilinx_properties,
> > +};
> > +
> > static void dwc3_xlnx_mask_phy_rst(struct dwc3_xlnx *priv_data, bool
> mask)
> > {
> > u32 reg;
> > @@ -288,10 +297,14 @@ static int dwc3_xlnx_probe(struct
> platform_device *pdev)
> > if (ret)
> > goto err_clk_put;
> >
> > - ret = of_platform_populate(np, NULL, NULL, dev);
> > + ret = device_add_software_node(dev, &dwc3_xilinx_swnode);
> > if (ret)
> > goto err_clk_put;
> >
> > + ret = of_platform_populate(np, NULL, NULL, dev);
> > + if (ret)
> > + goto err_remove_swnode;
> > +
> > pm_runtime_set_active(dev);
> > ret = devm_pm_runtime_enable(dev);
> > if (ret < 0)
> > @@ -303,6 +316,9 @@ static int dwc3_xlnx_probe(struct platform_device
> *pdev)
> > err_pm_set_suspended:
> > pm_runtime_set_suspended(dev);
> >
> > +err_remove_swnode:
> > + device_remove_software_node(dev);
> > +
> > err_clk_put:
> > clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data-
> >clks);
> >
> > --
> > 2.34.1
> >
>
> Thanks,
> Thinh
On Mon, Jun 10, 2024, Pandey, Radhey Shyam wrote:
> > -----Original Message-----
> > From: Thinh Nguyen <[email protected]>
> > Sent: Saturday, June 8, 2024 5:39 AM
> > To: Pandey, Radhey Shyam <[email protected]>
> > Cc: Thinh Nguyen <[email protected]>;
> > [email protected]; Simek, Michal <[email protected]>;
> > [email protected]; [email protected]; linux-
> > [email protected]; [email protected]; linux-arm-
> > [email protected]; git (AMD-Xilinx) <[email protected]>
> > Subject: Re: [PATCH v3] usb: dwc3: enable CCI support for AMD-xilinx DWC3
> > controller
> >
> > Hi,
> >
> > On Thu, Jun 06, 2024, Radhey Shyam Pandey wrote:
> > > The GSBUSCFG0 register bits [31:16] are used to configure the cache type
> > > settings of the descriptor and data write/read transfers (Cacheable,
> > > Bufferable/Posted). When CCI is enabled in the design, DWC3 core
> > GSBUSCFG0
> > > cache bits must be updated to support CCI enabled transfers in USB.
> > >
> > > To program GSBUSCFG0 cache bits create a software node property
> > > in AMD-xilinx dwc3 glue driver and pass it to dwc3 core. The core
> > > then reads this property value and configures it in dwc3_core_init()
> > > sequence.
> > >
> > > Signed-off-by: Radhey Shyam Pandey <[email protected]>
> > > ---
> > > Changes for v3:
> > > In v2 review as suggested by Thinh Nguyen, switch to swnode
> > implementation
> > > for passing GSBUSCFG0 cache bits from AMD-xilinx dwc3 glue driver to
> > > core driver.
> > >
> > > Changes for v2:
> > > Make GSBUSCFG0 configuration specific to AMD-xilinx platform.
> > > Taken reference from existing commit ec5eb43813a4 ("usb: dwc3: core:
> > > add support for realtek SoCs custom's global register start address")
> > >
> > > v1 link:
> > >
> > https://urldefense.com/v3/__https://lore.kernel.org/all/20231013053448.11
> > [email protected]__;!!A4F2R9G_pg!cOoWxmacxPeYVCxDfg3-
> > xlQLhKm8MIEgwWx45cLQjgwRWA4e4QyY_kGVVHo2m_dcRbpBQEFpB9JsYP6
> > nzasK2AIAsyefjQ$
> > > ---
> > > drivers/usb/dwc3/core.c | 24 ++++++++++++++++++++++++
> > > drivers/usb/dwc3/core.h | 8 ++++++++
> > > drivers/usb/dwc3/dwc3-xilinx.c | 18 +++++++++++++++++-
> > > 3 files changed, 49 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> > > index 7ee61a89520b..159d21b25629 100644
> > > --- a/drivers/usb/dwc3/core.c
> > > +++ b/drivers/usb/dwc3/core.c
> > > @@ -23,6 +23,7 @@
> > > #include <linux/delay.h>
> > > #include <linux/dma-mapping.h>
> > > #include <linux/of.h>
> > > +#include <linux/of_address.h>
> > > #include <linux/of_graph.h>
> > > #include <linux/acpi.h>
> > > #include <linux/pinctrl/consumer.h>
> > > @@ -599,6 +600,19 @@ static void dwc3_cache_hwparams(struct dwc3
> > *dwc)
> > > parms->hwparams9 = dwc3_readl(dwc->regs,
> > DWC3_GHWPARAMS9);
> > > }
> > >
> > > +static void dwc3_config_soc_bus(struct dwc3 *dwc)
> > > +{
> > > + if (of_dma_is_coherent(dwc->dev->of_node)) {
> >
> > This can be applicable outside of of_node, do we need this if case?
>
> This of_dma_is_coherent detect presence of dma-coherent property
> in dwc3 node and then if propery is present we program
> GSBUSCFG0_REQINFO.
>
> Alternatively glue driver can also read/detect DWC3 node dma-coherent
> property and then override snps,acache-data-rd-wr-info value only
> if dma-coherent property is present.
The user/designer of the platform should decide whether this property is
applicable to the platform. In this case, this logic should be applied
from your glue driver. If the user sets this property, apply the value
to the GSBUSCFG0 regardless of dma-coherent.
>
> Or do you mean we should support presence of dma-coherent
> property in either parent node ("xlnx,zynqmp-dwc3") or child
> node(snps,dwc3)?
See above.
>
> >
> > > + u32 reg;
> > > +
> > > + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
> > > + reg &=
> > ~DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK;
> > > + reg |= (dwc->acache_data_rd_wr_info <<
> >
> > What if the user doesn't specify this property? We should not
> > automatically write 0 by default.
>
> USB3 3.30a core configured for 2.0 I see reset value for
> GSBUSCFG0 [31:16] bits are 0. Will cross-check it for other
> versions.
Other platform may have a default setting from coreConsultant that's not
0. Let's not write 0 by default.
>
> >
> > > +
> > DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT);
> > > + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg);
> > > + }
> > > +}
> > > +
> > > static int dwc3_core_ulpi_init(struct dwc3 *dwc)
> > > {
> > > int intf;
> > > @@ -1320,6 +1334,8 @@ static int dwc3_core_init(struct dwc3 *dwc)
> > >
> > > dwc3_set_incr_burst_type(dwc);
> > >
> > > + dwc3_config_soc_bus(dwc);
> > > +
> > > ret = dwc3_phy_power_on(dwc);
> > > if (ret)
> > > goto err_exit_phy;
> > > @@ -1574,6 +1590,7 @@ static void dwc3_get_properties(struct dwc3
> > *dwc)
> > > u8 tx_max_burst_prd = 0;
> > > u8 tx_fifo_resize_max_num;
> > > const char *usb_psy_name;
> > > + struct device *tmpdev;
> > > int ret;
> > >
> > > /* default to highest possible threshold */
> > > @@ -1716,6 +1733,13 @@ static void dwc3_get_properties(struct dwc3
> > *dwc)
> > > dwc->dis_split_quirk = device_property_read_bool(dev,
> > > "snps,dis-split-quirk");
> > >
> > > + /* Iterate over all parent nodes for finding swnode properties */
> > > + for (tmpdev = dwc->dev; tmpdev; tmpdev = tmpdev->parent) {
> > > + device_property_read_u16(tmpdev,
> > > + "snps,acache-data-rd-wr-info",
> > > + &dwc->acache_data_rd_wr_info);
> > > + }
> > > +
> >
> > Please split this to a separate function and name it as
> > dwc3_get_software_properties(). For now, just the new property you
> > create is fine. We can introduce new patches to move all the software
> > defined properties (ie. non ABI/DS) there such as sysdev_is_parent.
>
> Sure , will split it to separate patch.
> >
> > > dwc->lpm_nyet_threshold = lpm_nyet_threshold;
> > > dwc->tx_de_emphasis = tx_de_emphasis;
> > >
> > > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> > > index 3781c736c1a1..57b3cb739353 100644
> > > --- a/drivers/usb/dwc3/core.h
> > > +++ b/drivers/usb/dwc3/core.h
> > > @@ -194,6 +194,10 @@
> > > #define DWC3_GSBUSCFG0_INCRBRSTENA (1 << 0) /* undefined length
> > enable */
> > > #define DWC3_GSBUSCFG0_INCRBRST_MASK 0xff
> > >
> > > +/* Global SoC Bus Configuration Register: AHB-prot/AXI-cache/OCP-
> > ReqInfo */
> > > +#define DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_MASK
> > GENMASK(31, 16)
> >
> > Can we rename this to DWC3_GSBUSCFG0_REQINFO_MASK
>
> Yes, will do it in next version.
>
> >
> > > +#define DWC3_GSBUSCFG0_DAT_DES_RD_WR_REQINFO_SHIFT 16
> >
> > We don't need a shift value. Either define DWC3_GSBUSCFG0_REQINFO(n) or
> > use FIELD_PREP and the mask.
>
> Yes, will fix it in next version.
> >
> > > +
> > > /* Global Debug LSP MUX Select */
> > > #define DWC3_GDBGLSPMUX_ENDBC BIT(15) /* Host only
> > */
> > > #define DWC3_GDBGLSPMUX_HOSTSELECT(n) ((n) & 0x3fff)
> > > @@ -1153,6 +1157,9 @@ struct dwc3_scratchpad_array {
> > > * @num_ep_resized: carries the current number endpoints which have
> > had its tx
> > > * fifo resized.
> > > * @debug_root: root debugfs directory for this device to put its files in.
> > > + * @acache_data_rd_wr_info: store GSBUSCFG0.DATRDREQINFO,
> > DESRDREQINFO,
> > > + * DATWRREQINFO, and DESWRREQINFO value passed from
> > > + * glue driver.
> > > */
> > > struct dwc3 {
> > > struct work_struct drd_work;
> > > @@ -1380,6 +1387,7 @@ struct dwc3 {
> > > int last_fifo_depth;
> > > int num_ep_resized;
> > > struct dentry *debug_root;
> > > + u16 acache_data_rd_wr_info;
> >
> > If we do need to keep this field around, please define the default
> > for unspecified value. Also rename this to gsbuscfg0_reqinfo.
>
> Sure. will define default (likely 0 ) and rename it to gsbuscfg0_reqinfo
> in next version.
The default should should not be a valid value that can be set. Perhaps
use type u32 and define 0xffffffff as unspecified?
Thanks,
Thinh