From: Graff Yang <[email protected]>
Signed-off-by: Graff Yang <[email protected]>
---
drivers/net/irda/Kconfig | 45 +++
drivers/net/irda/Makefile | 1 +
drivers/net/irda/bfin_sir.c | 814 +++++++++++++++++++++++++++++++++++++++++++
drivers/net/irda/bfin_sir.h | 147 ++++++++
4 files changed, 1007 insertions(+), 0 deletions(-)
create mode 100644 drivers/net/irda/bfin_sir.c
create mode 100644 drivers/net/irda/bfin_sir.h
diff --git a/drivers/net/irda/Kconfig b/drivers/net/irda/Kconfig
index e631755..985fec9 100644
--- a/drivers/net/irda/Kconfig
+++ b/drivers/net/irda/Kconfig
@@ -17,6 +17,51 @@ config IRTTY_SIR
If unsure, say Y.
+config BFIN_SIR
+ tristate "Blackfin SIR on UART"
+ depends on BLACKFIN && IRDA
+ default n
+ help
+ Say Y here if your want to enable SIR function on Blackfin UART
+ devices.
+
+ To activate this driver you can start irattach like:
+ "irattach irda0 -s"
+
+ Saying M, it will be built as a module named bfin_sir.
+
+ Note that you need to turn off one of the serial drivers for SIR
+ to use that UART.
+
+config BFIN_SIR0
+ bool "Blackfin SIR on UART0"
+ depends on BFIN_SIR && !SERIAL_BFIN_UART0
+
+config BFIN_SIR1
+ bool "Blackfin SIR on UART1"
+ depends on BFIN_SIR && !SERIAL_BFIN_UART1 && (!BF531 && !BF532 && !BF533 && !BF561)
+
+config BFIN_SIR2
+ bool "Blackfin SIR on UART2"
+ depends on BFIN_SIR && !SERIAL_BFIN_UART2 && (BF54x || BF538 || BF539)
+
+config BFIN_SIR3
+ bool "Blackfin SIR on UART3"
+ depends on BFIN_SIR && !SERIAL_BFIN_UART3 && (BF54x)
+
+choice
+ prompt "SIR Mode"
+ depends on BFIN_SIR
+ default SIR_BFIN_DMA
+
+config SIR_BFIN_DMA
+ bool "DMA mode"
+ depends on !DMA_UNCACHED_NONE
+
+config SIR_BFIN_PIO
+ bool "PIO mode"
+endchoice
+
comment "Dongle support"
config DONGLE
diff --git a/drivers/net/irda/Makefile b/drivers/net/irda/Makefile
index 5d20fde..d82e1e3 100644
--- a/drivers/net/irda/Makefile
+++ b/drivers/net/irda/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_MCS_FIR) += mcs7780.o
obj-$(CONFIG_AU1000_FIR) += au1k_ir.o
# SIR drivers
obj-$(CONFIG_IRTTY_SIR) += irtty-sir.o sir-dev.o
+obj-$(CONFIG_BFIN_SIR) += bfin_sir.o
# dongle drivers for SIR drivers
obj-$(CONFIG_ESI_DONGLE) += esi-sir.o
obj-$(CONFIG_TEKRAM_DONGLE) += tekram-sir.o
diff --git a/drivers/net/irda/bfin_sir.c b/drivers/net/irda/bfin_sir.c
new file mode 100644
index 0000000..38584cc
--- /dev/null
+++ b/drivers/net/irda/bfin_sir.c
@@ -0,0 +1,814 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2009 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+#include "bfin_sir.h"
+
+#ifdef CONFIG_SIR_BFIN_DMA
+#define DMA_SIR_RX_XCNT 10
+#define DMA_SIR_RX_YCNT (PAGE_SIZE / DMA_SIR_RX_XCNT)
+#define DMA_SIR_RX_FLUSH_JIFS (HZ * 4 / 250)
+#endif
+
+#if ANOMALY_05000447
+static int max_rate = 57600;
+#else
+static int max_rate = 115200;
+#endif
+
+static void turnaround_delay(unsigned long last_jif, int mtt)
+{
+ long ticks;
+
+ mtt = mtt < 10000 ? 10000 : mtt;
+ ticks = 1 + mtt / (USEC_PER_SEC / HZ);
+ schedule_timeout_uninterruptible(ticks);
+}
+
+static void __devinit bfin_sir_init_ports(struct bfin_sir_port *sp, struct platform_device *pdev)
+{
+ int i;
+ struct resource *res;
+
+ for (i = 0; i < pdev->num_resources; i++) {
+ res = &pdev->resource[i];
+ switch (res->flags) {
+ case IORESOURCE_MEM:
+ sp->membase = (void __iomem *)res->start;
+ break;
+ case IORESOURCE_IRQ:
+ sp->irq = res->start;
+ break;
+ case IORESOURCE_DMA:
+ sp->rx_dma_channel = res->start;
+ sp->tx_dma_channel = res->end;
+ break;
+ default:
+ break;
+ }
+ }
+
+ sp->clk = get_sclk();
+#ifdef CONFIG_SIR_BFIN_DMA
+ sp->tx_done = 1;
+ init_timer(&(sp->rx_dma_timer));
+#endif
+}
+
+static void bfin_sir_stop_tx(struct bfin_sir_port *port)
+{
+#ifdef CONFIG_SIR_BFIN_DMA
+ disable_dma(port->tx_dma_channel);
+#endif
+
+ while (!(SIR_UART_GET_LSR(port) & THRE)) {
+ cpu_relax();
+ continue;
+ }
+
+ SIR_UART_STOP_TX(port);
+}
+
+static void bfin_sir_enable_tx(struct bfin_sir_port *port)
+{
+ SIR_UART_ENABLE_TX(port);
+}
+
+static void bfin_sir_stop_rx(struct bfin_sir_port *port)
+{
+ SIR_UART_STOP_RX(port);
+}
+
+static void bfin_sir_enable_rx(struct bfin_sir_port *port)
+{
+ SIR_UART_ENABLE_RX(port);
+}
+
+static int bfin_sir_set_speed(struct bfin_sir_port *port, int speed)
+{
+ int ret = -EINVAL;
+ unsigned int quot;
+ unsigned short val, lsr, lcr;
+ static int utime;
+ int count = 10;
+
+ lcr = WLS(8);
+
+ switch (speed) {
+ case 9600:
+ case 19200:
+ case 38400:
+ case 57600:
+ case 115200:
+
+ quot = (port->clk + (8 * speed)) / (16 * speed)\
+ - ANOMALY_05000230;
+
+ do {
+ udelay(utime);
+ lsr = SIR_UART_GET_LSR(port);
+ } while (!(lsr & TEMT) && count--);
+
+ /* The useconds for 1 bits to transmit */
+ utime = 1000000 / speed + 1;
+
+ /* Clear UCEN bit to reset the UART state machine
+ * and control registers
+ */
+ val = SIR_UART_GET_GCTL(port);
+ val &= ~UCEN;
+ SIR_UART_PUT_GCTL(port, val);
+
+ /* Set DLAB in LCR to Access THR RBR IER */
+ SIR_UART_SET_DLAB(port);
+ SSYNC();
+
+ SIR_UART_PUT_DLL(port, quot & 0xFF);
+ SIR_UART_PUT_DLH(port, (quot >> 8) & 0xFF);
+ SSYNC();
+
+ /* Clear DLAB in LCR */
+ SIR_UART_CLEAR_DLAB(port);
+ SSYNC();
+
+ SIR_UART_PUT_LCR(port, lcr);
+
+ val = SIR_UART_GET_GCTL(port);
+ val |= UCEN;
+ SIR_UART_PUT_GCTL(port, val);
+
+ ret = 0;
+ break;
+ default:
+ printk(KERN_WARNING "bfin_sir: Invalid speed %d\n", speed);
+ break;
+ }
+
+ val = SIR_UART_GET_GCTL(port);
+ /* If not add the 'RPOLC', we can't catch the receive interrupt.
+ * It's related with the HW layout and the IR transiver.
+ */
+ val |= IREN | RPOLC;
+ SIR_UART_PUT_GCTL(port, val);
+ return ret;
+}
+
+static int bfin_sir_is_receiving(struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+
+ if (!(SIR_UART_GET_IER(port) & ERBFI))
+ return 0;
+ return self->rx_buff.state != OUTSIDE_FRAME;
+}
+
+#ifdef CONFIG_SIR_BFIN_PIO
+static void bfin_sir_tx_chars(struct net_device *dev)
+{
+ unsigned int chr;
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+
+ if (self->tx_buff.len != 0) {
+ chr = *(self->tx_buff.data);
+ SIR_UART_PUT_CHAR(port, chr);
+ self->tx_buff.data++;
+ self->tx_buff.len--;
+ } else {
+ self->stats.tx_packets++;
+ self->stats.tx_bytes += self->tx_buff.data - self->tx_buff.head;
+ if (self->newspeed) {
+ bfin_sir_set_speed(port, self->newspeed);
+ self->speed = self->newspeed;
+ self->newspeed = 0;
+ }
+ bfin_sir_stop_tx(port);
+ bfin_sir_enable_rx(port);
+ /* I'm hungry! */
+ netif_wake_queue(dev);
+ }
+}
+
+static void bfin_sir_rx_chars(struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+ unsigned char ch;
+
+ SIR_UART_CLEAR_LSR(port);
+ ch = SIR_UART_GET_CHAR(port);
+ async_unwrap_char(dev, &self->stats, &self->rx_buff, ch);
+ dev->last_rx = jiffies;
+}
+
+static irqreturn_t bfin_sir_rx_int(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+
+ spin_lock(&self->lock);
+ while ((SIR_UART_GET_LSR(port) & DR))
+ bfin_sir_rx_chars(dev);
+ spin_unlock(&self->lock);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t bfin_sir_tx_int(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+
+ spin_lock(&self->lock);
+ if (SIR_UART_GET_LSR(port) & THRE)
+ bfin_sir_tx_chars(dev);
+ spin_unlock(&self->lock);
+
+ return IRQ_HANDLED;
+}
+#endif /* CONFIG_SIR_BFIN_PIO */
+
+#ifdef CONFIG_SIR_BFIN_DMA
+static void bfin_sir_dma_tx_chars(struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+
+ if (!port->tx_done)
+ return;
+ port->tx_done = 0;
+
+ if (self->tx_buff.len == 0) {
+ self->stats.tx_packets++;
+ if (self->newspeed) {
+ bfin_sir_set_speed(port, self->newspeed);
+ self->speed = self->newspeed;
+ self->newspeed = 0;
+ }
+ bfin_sir_enable_rx(port);
+ port->tx_done = 1;
+ netif_wake_queue(dev);
+ return;
+ }
+
+ blackfin_dcache_flush_range((unsigned long)(self->tx_buff.data),
+ (unsigned long)(self->tx_buff.data+self->tx_buff.len));
+ set_dma_config(port->tx_dma_channel,
+ set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
+ INTR_ON_BUF, DIMENSION_LINEAR, DATA_SIZE_8,
+ DMA_SYNC_RESTART));
+ set_dma_start_addr(port->tx_dma_channel,
+ (unsigned long)(self->tx_buff.data));
+ set_dma_x_count(port->tx_dma_channel, self->tx_buff.len);
+ set_dma_x_modify(port->tx_dma_channel, 1);
+ enable_dma(port->tx_dma_channel);
+}
+
+static irqreturn_t bfin_sir_dma_tx_int(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+
+ spin_lock(&self->lock);
+ if (!(get_dma_curr_irqstat(port->tx_dma_channel) & DMA_RUN)) {
+ clear_dma_irqstat(port->tx_dma_channel);
+ bfin_sir_stop_tx(port);
+
+ self->stats.tx_packets++;
+ self->stats.tx_bytes += self->tx_buff.len;
+ self->tx_buff.len = 0;
+ if (self->newspeed) {
+ bfin_sir_set_speed(port, self->newspeed);
+ self->speed = self->newspeed;
+ self->newspeed = 0;
+ }
+ bfin_sir_enable_rx(port);
+ /* I'm hungry! */
+ netif_wake_queue(dev);
+ port->tx_done = 1;
+ }
+ spin_unlock(&self->lock);
+
+ return IRQ_HANDLED;
+}
+
+static void bfin_sir_dma_rx_chars(struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+ int i;
+
+ SIR_UART_CLEAR_LSR(port);
+
+ for (i = port->rx_dma_buf.head; i < port->rx_dma_buf.tail; i++)
+ async_unwrap_char(dev, &self->stats, &self->rx_buff, port->rx_dma_buf.buf[i]);
+}
+
+void bfin_sir_rx_dma_timeout(struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+ int x_pos, pos;
+ unsigned long flags;
+
+ spin_lock_irqsave(&self->lock, flags);
+ x_pos = DMA_SIR_RX_XCNT - get_dma_curr_xcount(port->rx_dma_channel);
+ if (x_pos == DMA_SIR_RX_XCNT)
+ x_pos = 0;
+
+ pos = port->rx_dma_nrows * DMA_SIR_RX_XCNT + x_pos;
+
+ if (pos > port->rx_dma_buf.tail) {
+ port->rx_dma_buf.tail = pos;
+ bfin_sir_dma_rx_chars(dev);
+ port->rx_dma_buf.head = port->rx_dma_buf.tail;
+ }
+ spin_unlock_irqrestore(&self->lock, flags);
+}
+
+static irqreturn_t bfin_sir_dma_rx_int(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+ unsigned short irqstat;
+
+ spin_lock(&self->lock);
+
+ port->rx_dma_nrows++;
+ port->rx_dma_buf.tail = DMA_SIR_RX_XCNT * port->rx_dma_nrows;
+ bfin_sir_dma_rx_chars(dev);
+ if (port->rx_dma_nrows >= DMA_SIR_RX_YCNT) {
+ port->rx_dma_nrows = 0;
+ port->rx_dma_buf.tail = 0;
+ }
+ port->rx_dma_buf.head = port->rx_dma_buf.tail;
+
+ irqstat = get_dma_curr_irqstat(port->rx_dma_channel);
+ clear_dma_irqstat(port->rx_dma_channel);
+ spin_unlock(&self->lock);
+
+ mod_timer(&port->rx_dma_timer, jiffies + DMA_SIR_RX_FLUSH_JIFS);
+ return IRQ_HANDLED;
+}
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+static int bfin_sir_startup(struct bfin_sir_port *port, struct net_device *dev)
+{
+#ifdef CONFIG_SIR_BFIN_DMA
+ dma_addr_t dma_handle;
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+ if (request_dma(port->rx_dma_channel, "BFIN_UART_RX") < 0) {
+ dev_warn(&dev->dev, "Unable to attach SIR RX DMA channel\n");
+ return -EBUSY;
+ }
+
+ if (request_dma(port->tx_dma_channel, "BFIN_UART_TX") < 0) {
+ dev_warn(&dev->dev, "Unable to attach SIR TX DMA channel\n");
+ free_dma(port->rx_dma_channel);
+ return -EBUSY;
+ }
+
+#ifdef CONFIG_SIR_BFIN_DMA
+
+ set_dma_callback(port->rx_dma_channel, bfin_sir_dma_rx_int, dev);
+ set_dma_callback(port->tx_dma_channel, bfin_sir_dma_tx_int, dev);
+
+ port->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
+ port->rx_dma_buf.head = 0;
+ port->rx_dma_buf.tail = 0;
+ port->rx_dma_nrows = 0;
+
+ set_dma_config(port->rx_dma_channel,
+ set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
+ INTR_ON_ROW, DIMENSION_2D,
+ DATA_SIZE_8, DMA_SYNC_RESTART));
+ set_dma_x_count(port->rx_dma_channel, DMA_SIR_RX_XCNT);
+ set_dma_x_modify(port->rx_dma_channel, 1);
+ set_dma_y_count(port->rx_dma_channel, DMA_SIR_RX_YCNT);
+ set_dma_y_modify(port->rx_dma_channel, 1);
+ set_dma_start_addr(port->rx_dma_channel, (unsigned long)port->rx_dma_buf.buf);
+ enable_dma(port->rx_dma_channel);
+
+ port->rx_dma_timer.data = (unsigned long)(dev);
+ port->rx_dma_timer.function = (void *)bfin_sir_rx_dma_timeout;
+
+#else
+
+ if (request_irq(port->irq, bfin_sir_rx_int, IRQF_DISABLED, "BFIN_SIR_RX", dev)) {
+ dev_warn(&dev->dev, "Unable to attach SIR RX interrupt\n");
+ return -EBUSY;
+ }
+
+ if (request_irq(port->irq+1, bfin_sir_tx_int, IRQF_DISABLED, "BFIN_SIR_TX", dev)) {
+ dev_warn(&dev->dev, "Unable to attach SIR TX interrupt\n");
+ free_irq(port->irq, dev);
+ return -EBUSY;
+ }
+#endif
+
+ return 0;
+}
+
+static void bfin_sir_shutdown(struct bfin_sir_port *port, struct net_device *dev)
+{
+ unsigned short val;
+
+ bfin_sir_stop_rx(port);
+ SIR_UART_DISABLE_INTS(port);
+
+ val = SIR_UART_GET_GCTL(port);
+ val &= ~(UCEN | IREN | RPOLC);
+ SIR_UART_PUT_GCTL(port, val);
+
+#ifdef CONFIG_SIR_BFIN_DMA
+ disable_dma(port->tx_dma_channel);
+ disable_dma(port->rx_dma_channel);
+ del_timer(&(port->rx_dma_timer));
+ dma_free_coherent(NULL, PAGE_SIZE, port->rx_dma_buf.buf, 0);
+#else
+ free_irq(port->irq+1, dev);
+ free_irq(port->irq, dev);
+#endif
+ free_dma(port->tx_dma_channel);
+ free_dma(port->rx_dma_channel);
+}
+
+#ifdef CONFIG_PM
+static int bfin_sir_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct bfin_sir_port *sir_port;
+ struct net_device *dev;
+ struct bfin_sir_self *self;
+
+ sir_port = platform_get_drvdata(pdev);
+ if (!sir_port)
+ return 0;
+
+ dev = sir_port->dev;
+ self = netdev_priv(dev);
+ if (self->open) {
+ flush_work(&self->work);
+ bfin_sir_shutdown(self->sir_port, dev);
+ netif_device_detach(dev);
+ }
+
+ return 0;
+}
+static int bfin_sir_resume(struct platform_device *pdev)
+{
+ struct bfin_sir_port *sir_port;
+ struct net_device *dev;
+ struct bfin_sir_self *self;
+ struct bfin_sir_port *port;
+
+ sir_port = platform_get_drvdata(pdev);
+ if (!sir_port)
+ return 0;
+
+ dev = sir_port->dev;
+ self = netdev_priv(dev);
+ port = self->sir_port;
+ if (self->open) {
+ if (self->newspeed) {
+ self->speed = self->newspeed;
+ self->newspeed = 0;
+ }
+ bfin_sir_startup(port, dev);
+ bfin_sir_set_speed(port, 9600);
+ bfin_sir_enable_rx(port);
+ netif_device_attach(dev);
+ }
+ return 0;
+}
+#else
+#define bfin_sir_suspend NULL
+#define bfin_sir_resume NULL
+#endif
+
+static void bfin_sir_send_work(struct work_struct *work)
+{
+ struct bfin_sir_self *self = container_of(work, struct bfin_sir_self, work);
+ struct net_device *dev = self->sir_port->dev;
+ struct bfin_sir_port *port = self->sir_port;
+ unsigned short val;
+ int tx_cnt = 10;
+
+ while (bfin_sir_is_receiving(dev) && --tx_cnt)
+ turnaround_delay(dev->last_rx, self->mtt);
+
+ bfin_sir_stop_rx(port);
+
+ /* To avoid losting RX interrupt, we reset IR function before
+ * sending data. We also can set the speed, which will
+ * reset all the UART.
+ */
+ val = SIR_UART_GET_GCTL(port);
+ val &= ~(IREN | RPOLC);
+ SIR_UART_PUT_GCTL(port, val);
+ SSYNC();
+ val |= IREN | RPOLC;
+ SIR_UART_PUT_GCTL(port, val);
+ SSYNC();
+ /* bfin_sir_set_speed(port, self->speed); */
+
+#ifdef CONFIG_SIR_BFIN_DMA
+ bfin_sir_dma_tx_chars(dev);
+#endif
+ bfin_sir_enable_tx(port);
+ dev->trans_start = jiffies;
+}
+
+static int bfin_sir_hard_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+ int speed = irda_get_next_speed(skb);
+
+ netif_stop_queue(dev);
+
+ self->mtt = irda_get_mtt(skb);
+
+ if (speed != self->speed && speed != -1)
+ self->newspeed = speed;
+
+ self->tx_buff.data = self->tx_buff.head;
+ if (skb->len == 0)
+ self->tx_buff.len = 0;
+ else
+ self->tx_buff.len = async_wrap_skb(skb, self->tx_buff.data, self->tx_buff.truesize);
+
+ schedule_work(&self->work);
+ dev_kfree_skb(skb);
+
+ return 0;
+}
+
+static int bfin_sir_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd)
+{
+ struct if_irda_req *rq = (struct if_irda_req *)ifreq;
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+ int ret = 0;
+
+ switch (cmd) {
+ case SIOCSBANDWIDTH:
+ if (capable(CAP_NET_ADMIN)) {
+ if (self->open) {
+ ret = bfin_sir_set_speed(port, rq->ifr_baudrate);
+ bfin_sir_enable_rx(port);
+ } else {
+ dev_warn(&dev->dev, "SIOCSBANDWIDTH: !netif_running\n");
+ ret = 0;
+ }
+ }
+ break;
+
+ case SIOCSMEDIABUSY:
+ ret = -EPERM;
+ if (capable(CAP_NET_ADMIN)) {
+ irda_device_set_media_busy(dev, TRUE);
+ ret = 0;
+ }
+ break;
+
+ case SIOCGRECEIVING:
+ rq->ifr_receiving = bfin_sir_is_receiving(dev);
+ break;
+
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+
+ return ret;
+}
+
+static struct net_device_stats *bfin_sir_stats(struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+
+ return &self->stats;
+}
+
+static int bfin_sir_open(struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+ struct bfin_sir_port *port = self->sir_port;
+ int err = -ENOMEM;
+
+ self->newspeed = 0;
+ self->speed = 9600;
+
+ spin_lock_init(&self->lock);
+
+ err = bfin_sir_startup(port, dev);
+ if (err)
+ goto err_startup;
+
+ bfin_sir_set_speed(port, 9600);
+
+ self->irlap = irlap_open(dev, &self->qos, DRIVER_NAME);
+ if (!self->irlap)
+ goto err_irlap;
+
+ INIT_WORK(&self->work, bfin_sir_send_work);
+
+ /*
+ * Now enable the interrupt then start the queue
+ */
+ self->open = 1;
+ bfin_sir_enable_rx(port);
+
+ netif_start_queue(dev);
+
+ return 0;
+
+err_irlap:
+ self->open = 0;
+ bfin_sir_shutdown(port, dev);
+err_startup:
+ return err;
+}
+
+static int bfin_sir_stop(struct net_device *dev)
+{
+ struct bfin_sir_self *self = netdev_priv(dev);
+
+ flush_work(&self->work);
+ bfin_sir_shutdown(self->sir_port, dev);
+
+ if (self->rxskb) {
+ dev_kfree_skb(self->rxskb);
+ self->rxskb = NULL;
+ }
+
+ /* Stop IrLAP */
+ if (self->irlap) {
+ irlap_close(self->irlap);
+ self->irlap = NULL;
+ }
+
+ netif_stop_queue(dev);
+ self->open = 0;
+
+ return 0;
+}
+
+static int bfin_sir_init_iobuf(iobuff_t *io, int size)
+{
+ io->head = kmalloc(size, GFP_KERNEL);
+ if (!io->head)
+ return -ENOMEM;
+ io->truesize = size;
+ io->in_frame = FALSE;
+ io->state = OUTSIDE_FRAME;
+ io->data = io->head;
+ return 0;
+}
+
+static int __devinit bfin_sir_probe(struct platform_device *pdev)
+{
+ struct net_device *dev;
+ struct bfin_sir_self *self;
+ unsigned int baudrate_mask;
+ struct bfin_sir_port *sir_port;
+ int err;
+
+ err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
+ if (err)
+ return err;
+
+ err = -ENOMEM;
+ sir_port = kmalloc(sizeof(*sir_port), GFP_KERNEL);
+ if (!sir_port)
+ goto err_mem_0;
+
+ bfin_sir_init_ports(sir_port, pdev);
+
+ dev = alloc_irdadev(sizeof(*self));
+ if (!dev)
+ goto err_mem_1;
+
+ self = netdev_priv(dev);
+ self->dev = &pdev->dev;
+ self->sir_port = sir_port;
+ sir_port->dev = dev;
+
+ err = bfin_sir_init_iobuf(&self->rx_buff, IRDA_SKB_MAX_MTU);
+ if (err)
+ goto err_mem_2;
+ err = bfin_sir_init_iobuf(&self->tx_buff, IRDA_SIR_MAX_FRAME);
+ if (err)
+ goto err_mem_3;
+
+ dev->hard_start_xmit = bfin_sir_hard_xmit;
+ dev->open = bfin_sir_open;
+ dev->stop = bfin_sir_stop;
+ dev->do_ioctl = bfin_sir_ioctl;
+ dev->get_stats = bfin_sir_stats;
+ dev->irq = sir_port->irq;
+
+ irda_init_max_qos_capabilies(&self->qos);
+
+ baudrate_mask = IR_9600;
+
+ switch (max_rate) {
+ case 115200:
+ baudrate_mask |= IR_115200;
+ case 57600:
+ baudrate_mask |= IR_57600;
+ case 38400:
+ baudrate_mask |= IR_38400;
+ case 19200:
+ baudrate_mask |= IR_19200;
+ case 9600:
+ break;
+ default:
+ printk(KERN_WARNING "bfin_sir: Invalid maximum baud rate, using 9600\n");
+ }
+
+ self->qos.baud_rate.bits &= baudrate_mask;
+
+ self->qos.min_turn_time.bits = 1; /* 10 ms or more */
+
+ irda_qos_bits_to_value(&self->qos);
+
+ err = register_netdev(dev);
+
+ if (err) {
+ kfree(self->tx_buff.head);
+err_mem_3:
+ kfree(self->rx_buff.head);
+err_mem_2:
+ free_netdev(dev);
+err_mem_1:
+ kfree(sir_port);
+err_mem_0:
+ peripheral_free_list(per[pdev->id]);
+ } else
+ platform_set_drvdata(pdev, sir_port);
+
+ return err;
+}
+
+static int __devexit bfin_sir_remove(struct platform_device *pdev)
+{
+ struct bfin_sir_port *sir_port;
+ struct net_device *dev = NULL;
+ struct bfin_sir_self *self;
+
+ sir_port = platform_get_drvdata(pdev);
+ if (!sir_port)
+ return 0;
+ dev = sir_port->dev;
+ self = netdev_priv(dev);
+ unregister_netdev(dev);
+ kfree(self->tx_buff.head);
+ kfree(self->rx_buff.head);
+ free_netdev(dev);
+ kfree(sir_port);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver bfin_ir_driver = {
+ .probe = bfin_sir_probe,
+ .remove = __devexit_p(bfin_sir_remove),
+ .suspend = bfin_sir_suspend,
+ .resume = bfin_sir_resume,
+ .driver = {
+ .name = DRIVER_NAME,
+ },
+};
+
+static int __init bfin_sir_init(void)
+{
+ return platform_driver_register(&bfin_ir_driver);
+}
+
+static void __exit bfin_sir_exit(void)
+{
+ platform_driver_unregister(&bfin_ir_driver);
+}
+
+module_init(bfin_sir_init);
+module_exit(bfin_sir_exit);
+
+module_param(max_rate, int, 0);
+MODULE_PARM_DESC(max_rate, "Maximum baud rate (115200, 57600, 38400, 19200, 9600)");
+
+MODULE_AUTHOR("Graf Yang <[email protected]>");
+MODULE_DESCRIPTION("Blackfin IrDA driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/irda/bfin_sir.h b/drivers/net/irda/bfin_sir.h
new file mode 100644
index 0000000..a723257
--- /dev/null
+++ b/drivers/net/irda/bfin_sir.h
@@ -0,0 +1,147 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2009 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+
+#include <net/irda/irda.h>
+#include <net/irda/wrapper.h>
+#include <net/irda/irda_device.h>
+
+#include <asm/irq.h>
+#include <asm/cacheflush.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+ char *buf;
+ int head;
+ int tail;
+};
+#endif
+
+struct bfin_sir_port {
+ unsigned char __iomem *membase;
+ unsigned int irq;
+ unsigned int lsr;
+ unsigned long clk;
+ struct net_device *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+ int tx_done;
+ struct dma_rx_buf rx_dma_buf;
+ struct timer_list rx_dma_timer;
+ int rx_dma_nrows;
+#endif
+ unsigned int tx_dma_channel;
+ unsigned int rx_dma_channel;
+};
+
+struct bfin_sir_port_res {
+ unsigned long base_addr;
+ int irq;
+ unsigned int rx_dma_channel;
+ unsigned int tx_dma_channel;
+};
+
+struct bfin_sir_self {
+ struct bfin_sir_port *sir_port;
+ spinlock_t lock;
+ unsigned int open;
+ int speed;
+ int newspeed;
+
+ struct sk_buff *txskb;
+ struct sk_buff *rxskb;
+ struct net_device_stats stats;
+ struct device *dev;
+ struct irlap_cb *irlap;
+ struct qos_info qos;
+
+ iobuff_t tx_buff;
+ iobuff_t rx_buff;
+
+ struct work_struct work;
+ int mtt;
+};
+
+#define DRIVER_NAME "bfin_sir"
+
+#define SIR_UART_GET_CHAR(port) bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port) bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_DLH(port) bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_LCR(port) bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_GCTL(port) bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v) bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_PUT_DLH(port, v) bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LCR(port, v) bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_BF54x
+#define SIR_UART_GET_LSR(port) bfin_read16((port)->membase + OFFSET_LSR)
+#define SIR_UART_GET_IER(port) bfin_read16((port)->membase + OFFSET_IER_SET)
+#define SIR_UART_SET_IER(port, v) bfin_write16(((port)->membase + OFFSET_IER_SET), v)
+#define SIR_UART_CLEAR_IER(port, v) bfin_write16(((port)->membase + OFFSET_IER_CLEAR), v)
+#define SIR_UART_PUT_LSR(port, v) bfin_write16(((port)->membase + OFFSET_LSR), v)
+#define SIR_UART_CLEAR_LSR(port) bfin_write16(((port)->membase + OFFSET_LSR), -1)
+
+#define SIR_UART_SET_DLAB(port)
+#define SIR_UART_CLEAR_DLAB(port)
+
+#define SIR_UART_ENABLE_INTS(port, v) SIR_UART_SET_IER(port, v)
+#define SIR_UART_DISABLE_INTS(port) SIR_UART_CLEAR_IER(port, 0xF)
+#define SIR_UART_STOP_TX(port) do { SIR_UART_PUT_LSR(port, TFI); SIR_UART_CLEAR_IER(port, ETBEI); } while (0)
+#define SIR_UART_ENABLE_TX(port) do { SIR_UART_SET_IER(port, ETBEI); } while (0)
+#define SIR_UART_STOP_RX(port) do { SIR_UART_CLEAR_IER(port, ERBFI); } while (0)
+#define SIR_UART_ENABLE_RX(port) do { SIR_UART_SET_IER(port, ERBFI); } while (0)
+#else
+
+#define SIR_UART_GET_IIR(port) bfin_read16((port)->membase + OFFSET_IIR)
+#define SIR_UART_GET_IER(port) bfin_read16((port)->membase + OFFSET_IER)
+#define SIR_UART_PUT_IER(port, v) bfin_write16(((port)->membase + OFFSET_IER), v)
+
+#define SIR_UART_SET_DLAB(port) do { SIR_UART_PUT_LCR(port, SIR_UART_GET_LCR(port) | DLAB); } while (0)
+#define SIR_UART_CLEAR_DLAB(port) do { SIR_UART_PUT_LCR(port, SIR_UART_GET_LCR(port) & ~DLAB); } while (0)
+
+#define SIR_UART_ENABLE_INTS(port, v) SIR_UART_PUT_IER(port, v)
+#define SIR_UART_DISABLE_INTS(port) SIR_UART_PUT_IER(port, 0)
+#define SIR_UART_STOP_TX(port) do { SIR_UART_PUT_IER(port, SIR_UART_GET_IER(port) & ~ETBEI); } while (0)
+#define SIR_UART_ENABLE_TX(port) do { SIR_UART_PUT_IER(port, SIR_UART_GET_IER(port) | ETBEI); } while (0)
+#define SIR_UART_STOP_RX(port) do { SIR_UART_PUT_IER(port, SIR_UART_GET_IER(port) & ~ERBFI); } while (0)
+#define SIR_UART_ENABLE_RX(port) do { SIR_UART_PUT_IER(port, SIR_UART_GET_IER(port) | ERBFI); } while (0)
+
+static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
+{
+ unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
+ port->lsr |= (lsr & (BI|FE|PE|OE));
+ return lsr | port->lsr;
+}
+
+static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
+{
+ port->lsr = 0;
+ bfin_read16(port->membase + OFFSET_LSR);
+}
+#endif
+
+static const unsigned short per[][3] = {
+ {P_UART0_RX, P_UART0_TX, 0},
+ {P_UART1_RX, P_UART1_TX, 0},
+ {P_UART2_RX, P_UART2_TX, 0},
+ {P_UART3_RX, P_UART3_TX, 0},
+};
--
1.6.1
On Wed, Mar 11, 2009 at 3:29 PM, <[email protected]> wrote:
> From: Graff Yang <[email protected]>
>
Generally, you need to change the title to '[PATCH] [net/irda]: new
Blackfin on-chip SIR IrDA driver (v2)" and add some change log here.
Because people don't want to review the whole code again and they just
want to know you updated something according to the LKML discussion.
v1-v2:
- item1
- item2
Something like this. Hope this is helpful, -:))
-Bryan
> Signed-off-by: Graff Yang <[email protected]>
> ---
> ?drivers/net/irda/Kconfig ? ?| ? 45 +++
> ?drivers/net/irda/Makefile ? | ? ?1 +
> ?drivers/net/irda/bfin_sir.c | ?814 +++++++++++++++++++++++++++++++++++++++++++
> ?drivers/net/irda/bfin_sir.h | ?147 ++++++++
> ?4 files changed, 1007 insertions(+), 0 deletions(-)
> ?create mode 100644 drivers/net/irda/bfin_sir.c
> ?create mode 100644 drivers/net/irda/bfin_sir.h
>
> diff --git a/drivers/net/irda/Kconfig b/drivers/net/irda/Kconfig
> index e631755..985fec9 100644
> --- a/drivers/net/irda/Kconfig
> +++ b/drivers/net/irda/Kconfig
> @@ -17,6 +17,51 @@ config IRTTY_SIR
>
> ? ? ? ? ?If unsure, say Y.
>
> +config BFIN_SIR
> + ? ? ? tristate "Blackfin SIR on UART"
> + ? ? ? depends on BLACKFIN && IRDA
> + ? ? ? default n
> + ? ? ? help
> + ? ? ? ? Say Y here if your want to enable SIR function on Blackfin UART
> + ? ? ? ? devices.
> +
> + ? ? ? ? To activate this driver you can start irattach like:
> + ? ? ? ? "irattach irda0 -s"
> +
> + ? ? ? ? Saying M, it will be built as a module named bfin_sir.
> +
> + ? ? ? ? Note that you need to turn off one of the serial drivers for SIR
> + ? ? ? ? to use that UART.
> +
> +config BFIN_SIR0
> + ? ? ? bool "Blackfin SIR on UART0"
> + ? ? ? depends on BFIN_SIR && !SERIAL_BFIN_UART0
> +
> +config BFIN_SIR1
> + ? ? ? bool "Blackfin SIR on UART1"
> + ? ? ? depends on BFIN_SIR && !SERIAL_BFIN_UART1 && (!BF531 && !BF532 && !BF533 && !BF561)
> +
> +config BFIN_SIR2
> + ? ? ? bool "Blackfin SIR on UART2"
> + ? ? ? depends on BFIN_SIR && !SERIAL_BFIN_UART2 && (BF54x || BF538 || BF539)
> +
> +config BFIN_SIR3
> + ? ? ? bool "Blackfin SIR on UART3"
> + ? ? ? depends on BFIN_SIR && !SERIAL_BFIN_UART3 && (BF54x)
> +
> +choice
> + ? ? ? prompt "SIR Mode"
> + ? ? ? depends on BFIN_SIR
> + ? ? ? default SIR_BFIN_DMA
> +
> +config SIR_BFIN_DMA
> + ? ? ? bool "DMA mode"
> + ? ? ? depends on !DMA_UNCACHED_NONE
> +
> +config SIR_BFIN_PIO
> + ? ? ? bool "PIO mode"
> +endchoice
> +
> ?comment "Dongle support"
>
> ?config DONGLE
> diff --git a/drivers/net/irda/Makefile b/drivers/net/irda/Makefile
> index 5d20fde..d82e1e3 100644
> --- a/drivers/net/irda/Makefile
> +++ b/drivers/net/irda/Makefile
> @@ -21,6 +21,7 @@ obj-$(CONFIG_MCS_FIR) ? ? ? ? += mcs7780.o
> ?obj-$(CONFIG_AU1000_FIR) ? ? ? += au1k_ir.o
> ?# SIR drivers
> ?obj-$(CONFIG_IRTTY_SIR) ? ? ? ? ? ? ? ?+= irtty-sir.o ?sir-dev.o
> +obj-$(CONFIG_BFIN_SIR) ? ? ? ? += bfin_sir.o
> ?# dongle drivers for SIR drivers
> ?obj-$(CONFIG_ESI_DONGLE) ? ? ? += esi-sir.o
> ?obj-$(CONFIG_TEKRAM_DONGLE) ? ?+= tekram-sir.o
> diff --git a/drivers/net/irda/bfin_sir.c b/drivers/net/irda/bfin_sir.c
> new file mode 100644
> index 0000000..38584cc
> --- /dev/null
> +++ b/drivers/net/irda/bfin_sir.c
> @@ -0,0 +1,814 @@
> +/*
> + * Blackfin Infra-red Driver
> + *
> + * Copyright 2006-2009 Analog Devices Inc.
> + *
> + * Enter bugs at http://blackfin.uclinux.org/
> + *
> + * Licensed under the GPL-2 or later.
> + *
> + */
> +#include "bfin_sir.h"
> +
> +#ifdef CONFIG_SIR_BFIN_DMA
> +#define DMA_SIR_RX_XCNT ? ? ? ?10
> +#define DMA_SIR_RX_YCNT ? ? ? ?(PAGE_SIZE / DMA_SIR_RX_XCNT)
> +#define DMA_SIR_RX_FLUSH_JIFS ?(HZ * 4 / 250)
> +#endif
> +
> +#if ANOMALY_05000447
> +static int max_rate = 57600;
> +#else
> +static int max_rate = 115200;
> +#endif
> +
> +static void turnaround_delay(unsigned long last_jif, int mtt)
> +{
> + ? ? ? long ticks;
> +
> + ? ? ? mtt = mtt < 10000 ? 10000 : mtt;
> + ? ? ? ticks = 1 + mtt / (USEC_PER_SEC / HZ);
> + ? ? ? schedule_timeout_uninterruptible(ticks);
> +}
> +
> +static void __devinit bfin_sir_init_ports(struct bfin_sir_port *sp, struct platform_device *pdev)
> +{
> + ? ? ? int i;
> + ? ? ? struct resource *res;
> +
> + ? ? ? for (i = 0; i < pdev->num_resources; i++) {
> + ? ? ? ? ? ? ? res = &pdev->resource[i];
> + ? ? ? ? ? ? ? switch (res->flags) {
> + ? ? ? ? ? ? ? case IORESOURCE_MEM:
> + ? ? ? ? ? ? ? ? ? ? ? sp->membase ? = (void __iomem *)res->start;
> + ? ? ? ? ? ? ? ? ? ? ? break;
> + ? ? ? ? ? ? ? case IORESOURCE_IRQ:
> + ? ? ? ? ? ? ? ? ? ? ? sp->irq = res->start;
> + ? ? ? ? ? ? ? ? ? ? ? break;
> + ? ? ? ? ? ? ? case IORESOURCE_DMA:
> + ? ? ? ? ? ? ? ? ? ? ? sp->rx_dma_channel = res->start;
> + ? ? ? ? ? ? ? ? ? ? ? sp->tx_dma_channel = res->end;
> + ? ? ? ? ? ? ? ? ? ? ? break;
> + ? ? ? ? ? ? ? default:
> + ? ? ? ? ? ? ? ? ? ? ? break;
> + ? ? ? ? ? ? ? }
> + ? ? ? }
> +
> + ? ? ? sp->clk = get_sclk();
> +#ifdef CONFIG_SIR_BFIN_DMA
> + ? ? ? sp->tx_done ? ? ? ?= 1;
> + ? ? ? init_timer(&(sp->rx_dma_timer));
> +#endif
> +}
> +
> +static void bfin_sir_stop_tx(struct bfin_sir_port *port)
> +{
> +#ifdef CONFIG_SIR_BFIN_DMA
> + ? ? ? disable_dma(port->tx_dma_channel);
> +#endif
> +
> + ? ? ? while (!(SIR_UART_GET_LSR(port) & THRE)) {
> + ? ? ? ? ? ? ? cpu_relax();
> + ? ? ? ? ? ? ? continue;
> + ? ? ? }
> +
> + ? ? ? SIR_UART_STOP_TX(port);
> +}
> +
> +static void bfin_sir_enable_tx(struct bfin_sir_port *port)
> +{
> + ? ? ? SIR_UART_ENABLE_TX(port);
> +}
> +
> +static void bfin_sir_stop_rx(struct bfin_sir_port *port)
> +{
> + ? ? ? SIR_UART_STOP_RX(port);
> +}
> +
> +static void bfin_sir_enable_rx(struct bfin_sir_port *port)
> +{
> + ? ? ? SIR_UART_ENABLE_RX(port);
> +}
> +
> +static int bfin_sir_set_speed(struct bfin_sir_port *port, int speed)
> +{
> + ? ? ? int ret = -EINVAL;
> + ? ? ? unsigned int quot;
> + ? ? ? unsigned short val, lsr, lcr;
> + ? ? ? static int utime;
> + ? ? ? int count = 10;
> +
> + ? ? ? lcr = WLS(8);
> +
> + ? ? ? switch (speed) {
> + ? ? ? case 9600:
> + ? ? ? case 19200:
> + ? ? ? case 38400:
> + ? ? ? case 57600:
> + ? ? ? case 115200:
> +
> + ? ? ? ? ? ? ? quot = (port->clk + (8 * speed)) / (16 * speed)\
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? - ANOMALY_05000230;
> +
> + ? ? ? ? ? ? ? do {
> + ? ? ? ? ? ? ? ? ? ? ? udelay(utime);
> + ? ? ? ? ? ? ? ? ? ? ? lsr = SIR_UART_GET_LSR(port);
> + ? ? ? ? ? ? ? } while (!(lsr & TEMT) && count--);
> +
> + ? ? ? ? ? ? ? /* The useconds for 1 bits to transmit */
> + ? ? ? ? ? ? ? utime = 1000000 / speed + 1;
> +
> + ? ? ? ? ? ? ? /* Clear UCEN bit to reset the UART state machine
> + ? ? ? ? ? ? ? ?* and control registers
> + ? ? ? ? ? ? ? ?*/
> + ? ? ? ? ? ? ? val = SIR_UART_GET_GCTL(port);
> + ? ? ? ? ? ? ? val &= ~UCEN;
> + ? ? ? ? ? ? ? SIR_UART_PUT_GCTL(port, val);
> +
> + ? ? ? ? ? ? ? /* Set DLAB in LCR to Access THR RBR IER */
> + ? ? ? ? ? ? ? SIR_UART_SET_DLAB(port);
> + ? ? ? ? ? ? ? SSYNC();
> +
> + ? ? ? ? ? ? ? SIR_UART_PUT_DLL(port, quot & 0xFF);
> + ? ? ? ? ? ? ? SIR_UART_PUT_DLH(port, (quot >> 8) & 0xFF);
> + ? ? ? ? ? ? ? SSYNC();
> +
> + ? ? ? ? ? ? ? /* Clear DLAB in LCR */
> + ? ? ? ? ? ? ? SIR_UART_CLEAR_DLAB(port);
> + ? ? ? ? ? ? ? SSYNC();
> +
> + ? ? ? ? ? ? ? SIR_UART_PUT_LCR(port, lcr);
> +
> + ? ? ? ? ? ? ? val = SIR_UART_GET_GCTL(port);
> + ? ? ? ? ? ? ? val |= UCEN;
> + ? ? ? ? ? ? ? SIR_UART_PUT_GCTL(port, val);
> +
> + ? ? ? ? ? ? ? ret = 0;
> + ? ? ? ? ? ? ? break;
> + ? ? ? default:
> + ? ? ? ? ? ? ? printk(KERN_WARNING "bfin_sir: Invalid speed %d\n", speed);
> + ? ? ? ? ? ? ? break;
> + ? ? ? }
> +
> + ? ? ? val = SIR_UART_GET_GCTL(port);
> + ? ? ? /* If not add the 'RPOLC', we can't catch the receive interrupt.
> + ? ? ? ?* It's related with the HW layout and the IR transiver.
> + ? ? ? ?*/
> + ? ? ? val |= IREN | RPOLC;
> + ? ? ? SIR_UART_PUT_GCTL(port, val);
> + ? ? ? return ret;
> +}
> +
> +static int bfin_sir_is_receiving(struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> +
> + ? ? ? if (!(SIR_UART_GET_IER(port) & ERBFI))
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? return self->rx_buff.state != OUTSIDE_FRAME;
> +}
> +
> +#ifdef CONFIG_SIR_BFIN_PIO
> +static void bfin_sir_tx_chars(struct net_device *dev)
> +{
> + ? ? ? unsigned int chr;
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> +
> + ? ? ? if (self->tx_buff.len != 0) {
> + ? ? ? ? ? ? ? chr = *(self->tx_buff.data);
> + ? ? ? ? ? ? ? SIR_UART_PUT_CHAR(port, chr);
> + ? ? ? ? ? ? ? self->tx_buff.data++;
> + ? ? ? ? ? ? ? self->tx_buff.len--;
> + ? ? ? } else {
> + ? ? ? ? ? ? ? self->stats.tx_packets++;
> + ? ? ? ? ? ? ? self->stats.tx_bytes += self->tx_buff.data - self->tx_buff.head;
> + ? ? ? ? ? ? ? if (self->newspeed) {
> + ? ? ? ? ? ? ? ? ? ? ? bfin_sir_set_speed(port, self->newspeed);
> + ? ? ? ? ? ? ? ? ? ? ? self->speed = self->newspeed;
> + ? ? ? ? ? ? ? ? ? ? ? self->newspeed = 0;
> + ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? bfin_sir_stop_tx(port);
> + ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
> + ? ? ? ? ? ? ? /* I'm hungry! */
> + ? ? ? ? ? ? ? netif_wake_queue(dev);
> + ? ? ? }
> +}
> +
> +static void bfin_sir_rx_chars(struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> + ? ? ? unsigned char ch;
> +
> + ? ? ? SIR_UART_CLEAR_LSR(port);
> + ? ? ? ch = SIR_UART_GET_CHAR(port);
> + ? ? ? async_unwrap_char(dev, &self->stats, &self->rx_buff, ch);
> + ? ? ? dev->last_rx = jiffies;
> +}
> +
> +static irqreturn_t bfin_sir_rx_int(int irq, void *dev_id)
> +{
> + ? ? ? struct net_device *dev = dev_id;
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> +
> + ? ? ? spin_lock(&self->lock);
> + ? ? ? while ((SIR_UART_GET_LSR(port) & DR))
> + ? ? ? ? ? ? ? bfin_sir_rx_chars(dev);
> + ? ? ? spin_unlock(&self->lock);
> +
> + ? ? ? return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t bfin_sir_tx_int(int irq, void *dev_id)
> +{
> + ? ? ? struct net_device *dev = dev_id;
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> +
> + ? ? ? spin_lock(&self->lock);
> + ? ? ? if (SIR_UART_GET_LSR(port) & THRE)
> + ? ? ? ? ? ? ? bfin_sir_tx_chars(dev);
> + ? ? ? spin_unlock(&self->lock);
> +
> + ? ? ? return IRQ_HANDLED;
> +}
> +#endif /* CONFIG_SIR_BFIN_PIO */
> +
> +#ifdef CONFIG_SIR_BFIN_DMA
> +static void bfin_sir_dma_tx_chars(struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> +
> + ? ? ? if (!port->tx_done)
> + ? ? ? ? ? ? ? return;
> + ? ? ? port->tx_done = 0;
> +
> + ? ? ? if (self->tx_buff.len == 0) {
> + ? ? ? ? ? ? ? self->stats.tx_packets++;
> + ? ? ? ? ? ? ? if (self->newspeed) {
> + ? ? ? ? ? ? ? ? ? ? ? bfin_sir_set_speed(port, self->newspeed);
> + ? ? ? ? ? ? ? ? ? ? ? self->speed = self->newspeed;
> + ? ? ? ? ? ? ? ? ? ? ? self->newspeed = 0;
> + ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
> + ? ? ? ? ? ? ? port->tx_done = 1;
> + ? ? ? ? ? ? ? netif_wake_queue(dev);
> + ? ? ? ? ? ? ? return;
> + ? ? ? }
> +
> + ? ? ? blackfin_dcache_flush_range((unsigned long)(self->tx_buff.data),
> + ? ? ? ? ? ? ? (unsigned long)(self->tx_buff.data+self->tx_buff.len));
> + ? ? ? set_dma_config(port->tx_dma_channel,
> + ? ? ? ? ? ? ? set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
> + ? ? ? ? ? ? ? ? ? ? ? INTR_ON_BUF, DIMENSION_LINEAR, DATA_SIZE_8,
> + ? ? ? ? ? ? ? ? ? ? ? DMA_SYNC_RESTART));
> + ? ? ? set_dma_start_addr(port->tx_dma_channel,
> + ? ? ? ? ? ? ? (unsigned long)(self->tx_buff.data));
> + ? ? ? set_dma_x_count(port->tx_dma_channel, self->tx_buff.len);
> + ? ? ? set_dma_x_modify(port->tx_dma_channel, 1);
> + ? ? ? enable_dma(port->tx_dma_channel);
> +}
> +
> +static irqreturn_t bfin_sir_dma_tx_int(int irq, void *dev_id)
> +{
> + ? ? ? struct net_device *dev = dev_id;
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> +
> + ? ? ? spin_lock(&self->lock);
> + ? ? ? if (!(get_dma_curr_irqstat(port->tx_dma_channel) & DMA_RUN)) {
> + ? ? ? ? ? ? ? clear_dma_irqstat(port->tx_dma_channel);
> + ? ? ? ? ? ? ? bfin_sir_stop_tx(port);
> +
> + ? ? ? ? ? ? ? self->stats.tx_packets++;
> + ? ? ? ? ? ? ? self->stats.tx_bytes += self->tx_buff.len;
> + ? ? ? ? ? ? ? self->tx_buff.len = 0;
> + ? ? ? ? ? ? ? if (self->newspeed) {
> + ? ? ? ? ? ? ? ? ? ? ? bfin_sir_set_speed(port, self->newspeed);
> + ? ? ? ? ? ? ? ? ? ? ? self->speed = self->newspeed;
> + ? ? ? ? ? ? ? ? ? ? ? self->newspeed = 0;
> + ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
> + ? ? ? ? ? ? ? /* I'm hungry! */
> + ? ? ? ? ? ? ? netif_wake_queue(dev);
> + ? ? ? ? ? ? ? port->tx_done = 1;
> + ? ? ? }
> + ? ? ? spin_unlock(&self->lock);
> +
> + ? ? ? return IRQ_HANDLED;
> +}
> +
> +static void bfin_sir_dma_rx_chars(struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> + ? ? ? int i;
> +
> + ? ? ? SIR_UART_CLEAR_LSR(port);
> +
> + ? ? ? for (i = port->rx_dma_buf.head; i < port->rx_dma_buf.tail; i++)
> + ? ? ? ? ? ? ? async_unwrap_char(dev, &self->stats, &self->rx_buff, port->rx_dma_buf.buf[i]);
> +}
> +
> +void bfin_sir_rx_dma_timeout(struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> + ? ? ? int x_pos, pos;
> + ? ? ? unsigned long flags;
> +
> + ? ? ? spin_lock_irqsave(&self->lock, flags);
> + ? ? ? x_pos = DMA_SIR_RX_XCNT - get_dma_curr_xcount(port->rx_dma_channel);
> + ? ? ? if (x_pos == DMA_SIR_RX_XCNT)
> + ? ? ? ? ? ? ? x_pos = 0;
> +
> + ? ? ? pos = port->rx_dma_nrows * DMA_SIR_RX_XCNT + x_pos;
> +
> + ? ? ? if (pos > port->rx_dma_buf.tail) {
> + ? ? ? ? ? ? ? port->rx_dma_buf.tail = pos;
> + ? ? ? ? ? ? ? bfin_sir_dma_rx_chars(dev);
> + ? ? ? ? ? ? ? port->rx_dma_buf.head = port->rx_dma_buf.tail;
> + ? ? ? }
> + ? ? ? spin_unlock_irqrestore(&self->lock, flags);
> +}
> +
> +static irqreturn_t bfin_sir_dma_rx_int(int irq, void *dev_id)
> +{
> + ? ? ? struct net_device *dev = dev_id;
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> + ? ? ? unsigned short irqstat;
> +
> + ? ? ? spin_lock(&self->lock);
> +
> + ? ? ? port->rx_dma_nrows++;
> + ? ? ? port->rx_dma_buf.tail = DMA_SIR_RX_XCNT * port->rx_dma_nrows;
> + ? ? ? bfin_sir_dma_rx_chars(dev);
> + ? ? ? if (port->rx_dma_nrows >= DMA_SIR_RX_YCNT) {
> + ? ? ? ? ? ? ? port->rx_dma_nrows = 0;
> + ? ? ? ? ? ? ? port->rx_dma_buf.tail = 0;
> + ? ? ? }
> + ? ? ? port->rx_dma_buf.head = port->rx_dma_buf.tail;
> +
> + ? ? ? irqstat = get_dma_curr_irqstat(port->rx_dma_channel);
> + ? ? ? clear_dma_irqstat(port->rx_dma_channel);
> + ? ? ? spin_unlock(&self->lock);
> +
> + ? ? ? mod_timer(&port->rx_dma_timer, jiffies + DMA_SIR_RX_FLUSH_JIFS);
> + ? ? ? return IRQ_HANDLED;
> +}
> +#endif /* CONFIG_SIR_BFIN_DMA */
> +
> +static int bfin_sir_startup(struct bfin_sir_port *port, struct net_device *dev)
> +{
> +#ifdef CONFIG_SIR_BFIN_DMA
> + ? ? ? dma_addr_t dma_handle;
> +#endif /* CONFIG_SIR_BFIN_DMA */
> +
> + ? ? ? if (request_dma(port->rx_dma_channel, "BFIN_UART_RX") < 0) {
> + ? ? ? ? ? ? ? dev_warn(&dev->dev, "Unable to attach SIR RX DMA channel\n");
> + ? ? ? ? ? ? ? return -EBUSY;
> + ? ? ? }
> +
> + ? ? ? if (request_dma(port->tx_dma_channel, "BFIN_UART_TX") < 0) {
> + ? ? ? ? ? ? ? dev_warn(&dev->dev, "Unable to attach SIR TX DMA channel\n");
> + ? ? ? ? ? ? ? free_dma(port->rx_dma_channel);
> + ? ? ? ? ? ? ? return -EBUSY;
> + ? ? ? }
> +
> +#ifdef CONFIG_SIR_BFIN_DMA
> +
> + ? ? ? set_dma_callback(port->rx_dma_channel, bfin_sir_dma_rx_int, dev);
> + ? ? ? set_dma_callback(port->tx_dma_channel, bfin_sir_dma_tx_int, dev);
> +
> + ? ? ? port->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
> + ? ? ? port->rx_dma_buf.head = 0;
> + ? ? ? port->rx_dma_buf.tail = 0;
> + ? ? ? port->rx_dma_nrows = 0;
> +
> + ? ? ? set_dma_config(port->rx_dma_channel,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? INTR_ON_ROW, DIMENSION_2D,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? DATA_SIZE_8, DMA_SYNC_RESTART));
> + ? ? ? set_dma_x_count(port->rx_dma_channel, DMA_SIR_RX_XCNT);
> + ? ? ? set_dma_x_modify(port->rx_dma_channel, 1);
> + ? ? ? set_dma_y_count(port->rx_dma_channel, DMA_SIR_RX_YCNT);
> + ? ? ? set_dma_y_modify(port->rx_dma_channel, 1);
> + ? ? ? set_dma_start_addr(port->rx_dma_channel, (unsigned long)port->rx_dma_buf.buf);
> + ? ? ? enable_dma(port->rx_dma_channel);
> +
> + ? ? ? port->rx_dma_timer.data = (unsigned long)(dev);
> + ? ? ? port->rx_dma_timer.function = (void *)bfin_sir_rx_dma_timeout;
> +
> +#else
> +
> + ? ? ? if (request_irq(port->irq, bfin_sir_rx_int, IRQF_DISABLED, "BFIN_SIR_RX", dev)) {
> + ? ? ? ? ? ? ? dev_warn(&dev->dev, "Unable to attach SIR RX interrupt\n");
> + ? ? ? ? ? ? ? return -EBUSY;
> + ? ? ? }
> +
> + ? ? ? if (request_irq(port->irq+1, bfin_sir_tx_int, IRQF_DISABLED, "BFIN_SIR_TX", dev)) {
> + ? ? ? ? ? ? ? dev_warn(&dev->dev, "Unable to attach SIR TX interrupt\n");
> + ? ? ? ? ? ? ? free_irq(port->irq, dev);
> + ? ? ? ? ? ? ? return -EBUSY;
> + ? ? ? }
> +#endif
> +
> + ? ? ? return 0;
> +}
> +
> +static void bfin_sir_shutdown(struct bfin_sir_port *port, struct net_device *dev)
> +{
> + ? ? ? unsigned short val;
> +
> + ? ? ? bfin_sir_stop_rx(port);
> + ? ? ? SIR_UART_DISABLE_INTS(port);
> +
> + ? ? ? val = SIR_UART_GET_GCTL(port);
> + ? ? ? val &= ~(UCEN | IREN | RPOLC);
> + ? ? ? SIR_UART_PUT_GCTL(port, val);
> +
> +#ifdef CONFIG_SIR_BFIN_DMA
> + ? ? ? disable_dma(port->tx_dma_channel);
> + ? ? ? disable_dma(port->rx_dma_channel);
> + ? ? ? del_timer(&(port->rx_dma_timer));
> + ? ? ? dma_free_coherent(NULL, PAGE_SIZE, port->rx_dma_buf.buf, 0);
> +#else
> + ? ? ? free_irq(port->irq+1, dev);
> + ? ? ? free_irq(port->irq, dev);
> +#endif
> + ? ? ? free_dma(port->tx_dma_channel);
> + ? ? ? free_dma(port->rx_dma_channel);
> +}
> +
> +#ifdef CONFIG_PM
> +static int bfin_sir_suspend(struct platform_device *pdev, pm_message_t state)
> +{
> + ? ? ? struct bfin_sir_port *sir_port;
> + ? ? ? struct net_device *dev;
> + ? ? ? struct bfin_sir_self *self;
> +
> + ? ? ? sir_port = platform_get_drvdata(pdev);
> + ? ? ? if (!sir_port)
> + ? ? ? ? ? ? ? return 0;
> +
> + ? ? ? dev = sir_port->dev;
> + ? ? ? self = netdev_priv(dev);
> + ? ? ? if (self->open) {
> + ? ? ? ? ? ? ? flush_work(&self->work);
> + ? ? ? ? ? ? ? bfin_sir_shutdown(self->sir_port, dev);
> + ? ? ? ? ? ? ? netif_device_detach(dev);
> + ? ? ? }
> +
> + ? ? ? return 0;
> +}
> +static int bfin_sir_resume(struct platform_device *pdev)
> +{
> + ? ? ? struct bfin_sir_port *sir_port;
> + ? ? ? struct net_device *dev;
> + ? ? ? struct bfin_sir_self *self;
> + ? ? ? struct bfin_sir_port *port;
> +
> + ? ? ? sir_port = platform_get_drvdata(pdev);
> + ? ? ? if (!sir_port)
> + ? ? ? ? ? ? ? return 0;
> +
> + ? ? ? dev = sir_port->dev;
> + ? ? ? self = netdev_priv(dev);
> + ? ? ? port = self->sir_port;
> + ? ? ? if (self->open) {
> + ? ? ? ? ? ? ? if (self->newspeed) {
> + ? ? ? ? ? ? ? ? ? ? ? self->speed = self->newspeed;
> + ? ? ? ? ? ? ? ? ? ? ? self->newspeed = 0;
> + ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? bfin_sir_startup(port, dev);
> + ? ? ? ? ? ? ? bfin_sir_set_speed(port, 9600);
> + ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
> + ? ? ? ? ? ? ? netif_device_attach(dev);
> + ? ? ? }
> + ? ? ? return 0;
> +}
> +#else
> +#define bfin_sir_suspend ? NULL
> +#define bfin_sir_resume ? ?NULL
> +#endif
> +
> +static void bfin_sir_send_work(struct work_struct *work)
> +{
> + ? ? ? struct bfin_sir_self ?*self = container_of(work, struct bfin_sir_self, work);
> + ? ? ? struct net_device *dev = self->sir_port->dev;
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> + ? ? ? unsigned short val;
> + ? ? ? int tx_cnt = 10;
> +
> + ? ? ? while (bfin_sir_is_receiving(dev) && --tx_cnt)
> + ? ? ? ? ? ? ? turnaround_delay(dev->last_rx, self->mtt);
> +
> + ? ? ? bfin_sir_stop_rx(port);
> +
> + ? ? ? /* To avoid losting RX interrupt, we reset IR function before
> + ? ? ? ?* sending data. We also can set the speed, which will
> + ? ? ? ?* reset all the UART.
> + ? ? ? ?*/
> + ? ? ? val = SIR_UART_GET_GCTL(port);
> + ? ? ? val &= ~(IREN | RPOLC);
> + ? ? ? SIR_UART_PUT_GCTL(port, val);
> + ? ? ? SSYNC();
> + ? ? ? val |= IREN | RPOLC;
> + ? ? ? SIR_UART_PUT_GCTL(port, val);
> + ? ? ? SSYNC();
> + ? ? ? /* bfin_sir_set_speed(port, self->speed); */
> +
> +#ifdef CONFIG_SIR_BFIN_DMA
> + ? ? ? bfin_sir_dma_tx_chars(dev);
> +#endif
> + ? ? ? bfin_sir_enable_tx(port);
> + ? ? ? dev->trans_start = jiffies;
> +}
> +
> +static int bfin_sir_hard_xmit(struct sk_buff *skb, struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? int speed = irda_get_next_speed(skb);
> +
> + ? ? ? netif_stop_queue(dev);
> +
> + ? ? ? self->mtt = irda_get_mtt(skb);
> +
> + ? ? ? if (speed != self->speed && speed != -1)
> + ? ? ? ? ? ? ? self->newspeed = speed;
> +
> + ? ? ? self->tx_buff.data = self->tx_buff.head;
> + ? ? ? if (skb->len == 0)
> + ? ? ? ? ? ? ? self->tx_buff.len = 0;
> + ? ? ? else
> + ? ? ? ? ? ? ? self->tx_buff.len = async_wrap_skb(skb, self->tx_buff.data, self->tx_buff.truesize);
> +
> + ? ? ? schedule_work(&self->work);
> + ? ? ? dev_kfree_skb(skb);
> +
> + ? ? ? return 0;
> +}
> +
> +static int bfin_sir_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd)
> +{
> + ? ? ? struct if_irda_req *rq = (struct if_irda_req *)ifreq;
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> + ? ? ? int ret = 0;
> +
> + ? ? ? switch (cmd) {
> + ? ? ? case SIOCSBANDWIDTH:
> + ? ? ? ? ? ? ? if (capable(CAP_NET_ADMIN)) {
> + ? ? ? ? ? ? ? ? ? ? ? if (self->open) {
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ret = bfin_sir_set_speed(port, rq->ifr_baudrate);
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
> + ? ? ? ? ? ? ? ? ? ? ? } else {
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? dev_warn(&dev->dev, "SIOCSBANDWIDTH: !netif_running\n");
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ret = 0;
> + ? ? ? ? ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? break;
> +
> + ? ? ? case SIOCSMEDIABUSY:
> + ? ? ? ? ? ? ? ret = -EPERM;
> + ? ? ? ? ? ? ? if (capable(CAP_NET_ADMIN)) {
> + ? ? ? ? ? ? ? ? ? ? ? irda_device_set_media_busy(dev, TRUE);
> + ? ? ? ? ? ? ? ? ? ? ? ret = 0;
> + ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? break;
> +
> + ? ? ? case SIOCGRECEIVING:
> + ? ? ? ? ? ? ? rq->ifr_receiving = bfin_sir_is_receiving(dev);
> + ? ? ? ? ? ? ? break;
> +
> + ? ? ? default:
> + ? ? ? ? ? ? ? ret = -EOPNOTSUPP;
> + ? ? ? ? ? ? ? break;
> + ? ? ? }
> +
> + ? ? ? return ret;
> +}
> +
> +static struct net_device_stats *bfin_sir_stats(struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> +
> + ? ? ? return &self->stats;
> +}
> +
> +static int bfin_sir_open(struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> + ? ? ? struct bfin_sir_port *port = self->sir_port;
> + ? ? ? int err = -ENOMEM;
> +
> + ? ? ? self->newspeed = 0;
> + ? ? ? self->speed = 9600;
> +
> + ? ? ? spin_lock_init(&self->lock);
> +
> + ? ? ? err = bfin_sir_startup(port, dev);
> + ? ? ? if (err)
> + ? ? ? ? ? ? ? goto err_startup;
> +
> + ? ? ? bfin_sir_set_speed(port, 9600);
> +
> + ? ? ? self->irlap = irlap_open(dev, &self->qos, DRIVER_NAME);
> + ? ? ? if (!self->irlap)
> + ? ? ? ? ? ? ? goto err_irlap;
> +
> + ? ? ? INIT_WORK(&self->work, bfin_sir_send_work);
> +
> + ? ? ? /*
> + ? ? ? ?* Now enable the interrupt then start the queue
> + ? ? ? ?*/
> + ? ? ? self->open = 1;
> + ? ? ? bfin_sir_enable_rx(port);
> +
> + ? ? ? netif_start_queue(dev);
> +
> + ? ? ? return 0;
> +
> +err_irlap:
> + ? ? ? self->open = 0;
> + ? ? ? bfin_sir_shutdown(port, dev);
> +err_startup:
> + ? ? ? return err;
> +}
> +
> +static int bfin_sir_stop(struct net_device *dev)
> +{
> + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
> +
> + ? ? ? flush_work(&self->work);
> + ? ? ? bfin_sir_shutdown(self->sir_port, dev);
> +
> + ? ? ? if (self->rxskb) {
> + ? ? ? ? ? ? ? dev_kfree_skb(self->rxskb);
> + ? ? ? ? ? ? ? self->rxskb = NULL;
> + ? ? ? }
> +
> + ? ? ? /* Stop IrLAP */
> + ? ? ? if (self->irlap) {
> + ? ? ? ? ? ? ? irlap_close(self->irlap);
> + ? ? ? ? ? ? ? self->irlap = NULL;
> + ? ? ? }
> +
> + ? ? ? netif_stop_queue(dev);
> + ? ? ? self->open = 0;
> +
> + ? ? ? return 0;
> +}
> +
> +static int bfin_sir_init_iobuf(iobuff_t *io, int size)
> +{
> + ? ? ? io->head = kmalloc(size, GFP_KERNEL);
> + ? ? ? if (!io->head)
> + ? ? ? ? ? ? ? return -ENOMEM;
> + ? ? ? io->truesize = size;
> + ? ? ? io->in_frame = FALSE;
> + ? ? ? io->state ? ?= OUTSIDE_FRAME;
> + ? ? ? io->data ? ? = io->head;
> + ? ? ? return 0;
> +}
> +
> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
> +{
> + ? ? ? struct net_device *dev;
> + ? ? ? struct bfin_sir_self *self;
> + ? ? ? unsigned int baudrate_mask;
> + ? ? ? struct bfin_sir_port *sir_port;
> + ? ? ? int err;
> +
> + ? ? ? err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
> + ? ? ? if (err)
> + ? ? ? ? ? ? ? return err;
> +
> + ? ? ? err = -ENOMEM;
> + ? ? ? sir_port = kmalloc(sizeof(*sir_port), GFP_KERNEL);
> + ? ? ? if (!sir_port)
> + ? ? ? ? ? ? ? goto err_mem_0;
> +
> + ? ? ? bfin_sir_init_ports(sir_port, pdev);
> +
> + ? ? ? dev = alloc_irdadev(sizeof(*self));
> + ? ? ? if (!dev)
> + ? ? ? ? ? ? ? goto err_mem_1;
> +
> + ? ? ? self = netdev_priv(dev);
> + ? ? ? self->dev = &pdev->dev;
> + ? ? ? self->sir_port = sir_port;
> + ? ? ? sir_port->dev = dev;
> +
> + ? ? ? err = bfin_sir_init_iobuf(&self->rx_buff, IRDA_SKB_MAX_MTU);
> + ? ? ? if (err)
> + ? ? ? ? ? ? ? goto err_mem_2;
> + ? ? ? err = bfin_sir_init_iobuf(&self->tx_buff, IRDA_SIR_MAX_FRAME);
> + ? ? ? if (err)
> + ? ? ? ? ? ? ? goto err_mem_3;
> +
> + ? ? ? dev->hard_start_xmit = bfin_sir_hard_xmit;
> + ? ? ? dev->open ? ? ? ? ? ?= bfin_sir_open;
> + ? ? ? dev->stop ? ? ? ? ? ?= bfin_sir_stop;
> + ? ? ? dev->do_ioctl ? ? ? ?= bfin_sir_ioctl;
> + ? ? ? dev->get_stats ? ? ? = bfin_sir_stats;
> + ? ? ? dev->irq ? ? ? ? ? ? = sir_port->irq;
> +
> + ? ? ? irda_init_max_qos_capabilies(&self->qos);
> +
> + ? ? ? baudrate_mask = IR_9600;
> +
> + ? ? ? switch (max_rate) {
> + ? ? ? case 115200:
> + ? ? ? ? ? ? ? baudrate_mask |= IR_115200;
> + ? ? ? case 57600:
> + ? ? ? ? ? ? ? baudrate_mask |= IR_57600;
> + ? ? ? case 38400:
> + ? ? ? ? ? ? ? baudrate_mask |= IR_38400;
> + ? ? ? case 19200:
> + ? ? ? ? ? ? ? baudrate_mask |= IR_19200;
> + ? ? ? case 9600:
> + ? ? ? ? ? ? ? break;
> + ? ? ? default:
> + ? ? ? ? ? ? ? printk(KERN_WARNING "bfin_sir: Invalid maximum baud rate, using 9600\n");
> + ? ? ? }
> +
> + ? ? ? self->qos.baud_rate.bits &= baudrate_mask;
> +
> + ? ? ? self->qos.min_turn_time.bits = 1; /* 10 ms or more */
> +
> + ? ? ? irda_qos_bits_to_value(&self->qos);
> +
> + ? ? ? err = register_netdev(dev);
> +
> + ? ? ? if (err) {
> + ? ? ? ? ? ? ? kfree(self->tx_buff.head);
> +err_mem_3:
> + ? ? ? ? ? ? ? kfree(self->rx_buff.head);
> +err_mem_2:
> + ? ? ? ? ? ? ? free_netdev(dev);
> +err_mem_1:
> + ? ? ? ? ? ? ? kfree(sir_port);
> +err_mem_0:
> + ? ? ? ? ? ? ? peripheral_free_list(per[pdev->id]);
> + ? ? ? } else
> + ? ? ? ? ? ? ? platform_set_drvdata(pdev, sir_port);
> +
> + ? ? ? return err;
> +}
> +
> +static int __devexit bfin_sir_remove(struct platform_device *pdev)
> +{
> + ? ? ? struct bfin_sir_port *sir_port;
> + ? ? ? struct net_device *dev = NULL;
> + ? ? ? struct bfin_sir_self *self;
> +
> + ? ? ? sir_port = platform_get_drvdata(pdev);
> + ? ? ? if (!sir_port)
> + ? ? ? ? ? ? ? return 0;
> + ? ? ? dev = sir_port->dev;
> + ? ? ? self = netdev_priv(dev);
> + ? ? ? unregister_netdev(dev);
> + ? ? ? kfree(self->tx_buff.head);
> + ? ? ? kfree(self->rx_buff.head);
> + ? ? ? free_netdev(dev);
> + ? ? ? kfree(sir_port);
> + ? ? ? platform_set_drvdata(pdev, NULL);
> +
> + ? ? ? return 0;
> +}
> +
> +static struct platform_driver bfin_ir_driver = {
> + ? ? ? .probe ? = bfin_sir_probe,
> + ? ? ? .remove ?= __devexit_p(bfin_sir_remove),
> + ? ? ? .suspend = bfin_sir_suspend,
> + ? ? ? .resume ?= bfin_sir_resume,
> + ? ? ? .driver ?= {
> + ? ? ? ? ? ? ? .name = DRIVER_NAME,
> + ? ? ? },
> +};
> +
> +static int __init bfin_sir_init(void)
> +{
> + ? ? ? return platform_driver_register(&bfin_ir_driver);
> +}
> +
> +static void __exit bfin_sir_exit(void)
> +{
> + ? ? ? platform_driver_unregister(&bfin_ir_driver);
> +}
> +
> +module_init(bfin_sir_init);
> +module_exit(bfin_sir_exit);
> +
> +module_param(max_rate, int, 0);
> +MODULE_PARM_DESC(max_rate, "Maximum baud rate (115200, 57600, 38400, 19200, 9600)");
> +
> +MODULE_AUTHOR("Graf Yang <[email protected]>");
> +MODULE_DESCRIPTION("Blackfin IrDA driver");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/net/irda/bfin_sir.h b/drivers/net/irda/bfin_sir.h
> new file mode 100644
> index 0000000..a723257
> --- /dev/null
> +++ b/drivers/net/irda/bfin_sir.h
> @@ -0,0 +1,147 @@
> +/*
> + * Blackfin Infra-red Driver
> + *
> + * Copyright 2006-2009 Analog Devices Inc.
> + *
> + * Enter bugs at http://blackfin.uclinux.org/
> + *
> + * Licensed under the GPL-2 or later.
> + *
> + */
> +
> +#include <linux/serial.h>
> +#include <linux/module.h>
> +#include <linux/netdevice.h>
> +#include <linux/interrupt.h>
> +#include <linux/delay.h>
> +#include <linux/platform_device.h>
> +#include <linux/dma-mapping.h>
> +
> +#include <net/irda/irda.h>
> +#include <net/irda/wrapper.h>
> +#include <net/irda/irda_device.h>
> +
> +#include <asm/irq.h>
> +#include <asm/cacheflush.h>
> +#include <asm/dma.h>
> +#include <asm/portmux.h>
> +
> +#ifdef CONFIG_SIR_BFIN_DMA
> +struct dma_rx_buf {
> + ? ? ? char *buf;
> + ? ? ? int head;
> + ? ? ? int tail;
> +};
> +#endif
> +
> +struct bfin_sir_port {
> + ? ? ? unsigned char __iomem ? *membase;
> + ? ? ? unsigned int ? ? ? ? ? ?irq;
> + ? ? ? unsigned int ? ? ? ? ? ?lsr;
> + ? ? ? unsigned long ? ? ? ? ? clk;
> + ? ? ? struct net_device ? ? ? *dev;
> +#ifdef CONFIG_SIR_BFIN_DMA
> + ? ? ? int ? ? ? ? ? ? ? ? ? ? tx_done;
> + ? ? ? struct dma_rx_buf ? ? ? rx_dma_buf;
> + ? ? ? struct timer_list ? ? ? rx_dma_timer;
> + ? ? ? int ? ? ? ? ? ? ? ? ? ? rx_dma_nrows;
> +#endif
> + ? ? ? unsigned int ? ? ? ? ? ?tx_dma_channel;
> + ? ? ? unsigned int ? ? ? ? ? ?rx_dma_channel;
> +};
> +
> +struct bfin_sir_port_res {
> + ? ? ? unsigned long ? base_addr;
> + ? ? ? int ? ? ? ? ? ? irq;
> + ? ? ? unsigned int ? ?rx_dma_channel;
> + ? ? ? unsigned int ? ?tx_dma_channel;
> +};
> +
> +struct bfin_sir_self {
> + ? ? ? struct bfin_sir_port ? ?*sir_port;
> + ? ? ? spinlock_t ? ? ? ? ? ? ?lock;
> + ? ? ? unsigned int ? ? ? ? ? ?open;
> + ? ? ? int ? ? ? ? ? ? ? ? ? ? speed;
> + ? ? ? int ? ? ? ? ? ? ? ? ? ? newspeed;
> +
> + ? ? ? struct sk_buff ? ? ? ? ?*txskb;
> + ? ? ? struct sk_buff ? ? ? ? ?*rxskb;
> + ? ? ? struct net_device_stats stats;
> + ? ? ? struct device ? ? ? ? ? *dev;
> + ? ? ? struct irlap_cb ? ? ? ? *irlap;
> + ? ? ? struct qos_info ? ? ? ? qos;
> +
> + ? ? ? iobuff_t ? ? ? ? ? ? ? ?tx_buff;
> + ? ? ? iobuff_t ? ? ? ? ? ? ? ?rx_buff;
> +
> + ? ? ? struct work_struct ? ? ?work;
> + ? ? ? int ? ? ? ? ? ? ? ? ? ? mtt;
> +};
> +
> +#define DRIVER_NAME "bfin_sir"
> +
> +#define SIR_UART_GET_CHAR(port) ? ?bfin_read16((port)->membase + OFFSET_RBR)
> +#define SIR_UART_GET_DLL(port) ? ? bfin_read16((port)->membase + OFFSET_DLL)
> +#define SIR_UART_GET_DLH(port) ? ? bfin_read16((port)->membase + OFFSET_DLH)
> +#define SIR_UART_GET_LCR(port) ? ? bfin_read16((port)->membase + OFFSET_LCR)
> +#define SIR_UART_GET_GCTL(port) ? ?bfin_read16((port)->membase + OFFSET_GCTL)
> +
> +#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
> +#define SIR_UART_PUT_DLL(port, v) ?bfin_write16(((port)->membase + OFFSET_DLL), v)
> +#define SIR_UART_PUT_DLH(port, v) ?bfin_write16(((port)->membase + OFFSET_DLH), v)
> +#define SIR_UART_PUT_LCR(port, v) ?bfin_write16(((port)->membase + OFFSET_LCR), v)
> +#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
> +
> +#ifdef CONFIG_BF54x
> +#define SIR_UART_GET_LSR(port) ? ? bfin_read16((port)->membase + OFFSET_LSR)
> +#define SIR_UART_GET_IER(port) ? ? bfin_read16((port)->membase + OFFSET_IER_SET)
> +#define SIR_UART_SET_IER(port, v) ?bfin_write16(((port)->membase + OFFSET_IER_SET), v)
> +#define SIR_UART_CLEAR_IER(port, v) bfin_write16(((port)->membase + OFFSET_IER_CLEAR), v)
> +#define SIR_UART_PUT_LSR(port, v) ?bfin_write16(((port)->membase + OFFSET_LSR), v)
> +#define SIR_UART_CLEAR_LSR(port) ? bfin_write16(((port)->membase + OFFSET_LSR), -1)
> +
> +#define SIR_UART_SET_DLAB(port)
> +#define SIR_UART_CLEAR_DLAB(port)
> +
> +#define SIR_UART_ENABLE_INTS(port, v) SIR_UART_SET_IER(port, v)
> +#define SIR_UART_DISABLE_INTS(port) ? SIR_UART_CLEAR_IER(port, 0xF)
> +#define SIR_UART_STOP_TX(port) ? ? do { SIR_UART_PUT_LSR(port, TFI); SIR_UART_CLEAR_IER(port, ETBEI); } while (0)
> +#define SIR_UART_ENABLE_TX(port) ? do { SIR_UART_SET_IER(port, ETBEI); } while (0)
> +#define SIR_UART_STOP_RX(port) ? ? do { SIR_UART_CLEAR_IER(port, ERBFI); } while (0)
> +#define SIR_UART_ENABLE_RX(port) ? do { SIR_UART_SET_IER(port, ERBFI); } while (0)
> +#else
> +
> +#define SIR_UART_GET_IIR(port) ? ? bfin_read16((port)->membase + OFFSET_IIR)
> +#define SIR_UART_GET_IER(port) ? ? bfin_read16((port)->membase + OFFSET_IER)
> +#define SIR_UART_PUT_IER(port, v) ?bfin_write16(((port)->membase + OFFSET_IER), v)
> +
> +#define SIR_UART_SET_DLAB(port) ? ?do { SIR_UART_PUT_LCR(port, SIR_UART_GET_LCR(port) | DLAB); } while (0)
> +#define SIR_UART_CLEAR_DLAB(port) ?do { SIR_UART_PUT_LCR(port, SIR_UART_GET_LCR(port) & ~DLAB); } while (0)
> +
> +#define SIR_UART_ENABLE_INTS(port, v) SIR_UART_PUT_IER(port, v)
> +#define SIR_UART_DISABLE_INTS(port) ? SIR_UART_PUT_IER(port, 0)
> +#define SIR_UART_STOP_TX(port) ? ? do { SIR_UART_PUT_IER(port, SIR_UART_GET_IER(port) & ~ETBEI); } while (0)
> +#define SIR_UART_ENABLE_TX(port) ? do { SIR_UART_PUT_IER(port, SIR_UART_GET_IER(port) | ETBEI); } while (0)
> +#define SIR_UART_STOP_RX(port) ? ? do { SIR_UART_PUT_IER(port, SIR_UART_GET_IER(port) & ~ERBFI); } while (0)
> +#define SIR_UART_ENABLE_RX(port) ? do { SIR_UART_PUT_IER(port, SIR_UART_GET_IER(port) | ERBFI); } while (0)
> +
> +static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
> +{
> + ? ? ? unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
> + ? ? ? port->lsr |= (lsr & (BI|FE|PE|OE));
> + ? ? ? return lsr | port->lsr;
> +}
> +
> +static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
> +{
> + ? ? ? port->lsr = 0;
> + ? ? ? bfin_read16(port->membase + OFFSET_LSR);
> +}
> +#endif
> +
> +static const unsigned short per[][3] = {
> + ? ? ? {P_UART0_RX, P_UART0_TX, 0},
> + ? ? ? {P_UART1_RX, P_UART1_TX, 0},
> + ? ? ? {P_UART2_RX, P_UART2_TX, 0},
> + ? ? ? {P_UART3_RX, P_UART3_TX, 0},
> +};
> --
> 1.6.1
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> More majordomo info at ?http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at ?http://www.tux.org/lkml/
>
On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
> +{
> + struct net_device *dev;
> + struct bfin_sir_self *self;
> + unsigned int baudrate_mask;
> + struct bfin_sir_port *sir_port;
> + int err;
> +
> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
what if pdev->id is set to 12512 ?
> + switch (max_rate) {
> + default:
> + printk(KERN_WARNING "bfin_sir: Invalid maximum baud rate, using 9600\n");
dev_warn(&dev->dev,....) ?
-mike
On Wed, Mar 11, 2009 at 4:17 PM, graff yang <[email protected]> wrote:
> OK, thank you very much.
>
> Can I add the changed items here?
> It is the v3 version since the first patch on 2009-03-06.
>
> v1-v2: Revised according suggestions from Andrew Morton
> ? 1. Use schedule_timeout_uninterruptible() instead of
> schedule_timeout_interruptible() in function turnaround_delay()
> ? 2. Add cpu_relax() in bfin_sir_stop_tx()
> ? 3. Add spin lock/unlock in bfin_sir_tx_int() and bfin_sir_rx_int()
> ? 4. Use flush_work() instead of flush_scheduled_work() in bfin_sir_stop()
> and bfin_sir_suspend()
> ? 5. Remove GFP_DMA when calling kmalloc() in bfin_sir_init_iobuf()
> ? 6. Some revisions for coding style
>
> v2-v3: Revised according suggestions from Mike Frysinger
> ? 1. Change the BFIN_SIRx order in Kconfig
> ? 2. Add ANOMALY_05000230 when calculate baud rate divisor
> ? 3. Add a degressive counter to wait the byte sending out when going to
> change speed
> ? 4. Fixed the peripheral resource leakage
> ? 5. Some revision for coding style
>
> -Graff
>
IMHO, this is good enough, -:))
-Bryan
> On Wed, Mar 11, 2009 at 3:37 PM, Bryan Wu <[email protected]> wrote:
>>
>> On Wed, Mar 11, 2009 at 3:29 PM, ?<[email protected]> wrote:
>> > From: Graff Yang <[email protected]>
>> >
>>
>> Generally, you need to change the title to '[PATCH] [net/irda]: new
>> Blackfin on-chip SIR IrDA driver (v2)" and add some change log here.
>> Because people don't want to review the whole code again and they just
>> want to know you updated something according to the LKML discussion.
>>
>> v1-v2:
>> ?- item1
>> ?- item2
>>
>> Something like this. Hope this is helpful, -:))
>> -Bryan
>>
>> > Signed-off-by: Graff Yang <[email protected]>
>> > ---
>> > ?drivers/net/irda/Kconfig ? ?| ? 45 +++
>> > ?drivers/net/irda/Makefile ? | ? ?1 +
>> > ?drivers/net/irda/bfin_sir.c | ?814
>> > +++++++++++++++++++++++++++++++++++++++++++
>> > ?drivers/net/irda/bfin_sir.h | ?147 ++++++++
>> > ?4 files changed, 1007 insertions(+), 0 deletions(-)
>> > ?create mode 100644 drivers/net/irda/bfin_sir.c
>> > ?create mode 100644 drivers/net/irda/bfin_sir.h
>> >
>> > diff --git a/drivers/net/irda/Kconfig b/drivers/net/irda/Kconfig
>> > index e631755..985fec9 100644
>> > --- a/drivers/net/irda/Kconfig
>> > +++ b/drivers/net/irda/Kconfig
>> > @@ -17,6 +17,51 @@ config IRTTY_SIR
>> >
>> > ? ? ? ? ?If unsure, say Y.
>> >
>> > +config BFIN_SIR
>> > + ? ? ? tristate "Blackfin SIR on UART"
>> > + ? ? ? depends on BLACKFIN && IRDA
>> > + ? ? ? default n
>> > + ? ? ? help
>> > + ? ? ? ? Say Y here if your want to enable SIR function on Blackfin
>> > UART
>> > + ? ? ? ? devices.
>> > +
>> > + ? ? ? ? To activate this driver you can start irattach like:
>> > + ? ? ? ? "irattach irda0 -s"
>> > +
>> > + ? ? ? ? Saying M, it will be built as a module named bfin_sir.
>> > +
>> > + ? ? ? ? Note that you need to turn off one of the serial drivers for
>> > SIR
>> > + ? ? ? ? to use that UART.
>> > +
>> > +config BFIN_SIR0
>> > + ? ? ? bool "Blackfin SIR on UART0"
>> > + ? ? ? depends on BFIN_SIR && !SERIAL_BFIN_UART0
>> > +
>> > +config BFIN_SIR1
>> > + ? ? ? bool "Blackfin SIR on UART1"
>> > + ? ? ? depends on BFIN_SIR && !SERIAL_BFIN_UART1 && (!BF531 && !BF532
>> > && !BF533 && !BF561)
>> > +
>> > +config BFIN_SIR2
>> > + ? ? ? bool "Blackfin SIR on UART2"
>> > + ? ? ? depends on BFIN_SIR && !SERIAL_BFIN_UART2 && (BF54x || BF538 ||
>> > BF539)
>> > +
>> > +config BFIN_SIR3
>> > + ? ? ? bool "Blackfin SIR on UART3"
>> > + ? ? ? depends on BFIN_SIR && !SERIAL_BFIN_UART3 && (BF54x)
>> > +
>> > +choice
>> > + ? ? ? prompt "SIR Mode"
>> > + ? ? ? depends on BFIN_SIR
>> > + ? ? ? default SIR_BFIN_DMA
>> > +
>> > +config SIR_BFIN_DMA
>> > + ? ? ? bool "DMA mode"
>> > + ? ? ? depends on !DMA_UNCACHED_NONE
>> > +
>> > +config SIR_BFIN_PIO
>> > + ? ? ? bool "PIO mode"
>> > +endchoice
>> > +
>> > ?comment "Dongle support"
>> >
>> > ?config DONGLE
>> > diff --git a/drivers/net/irda/Makefile b/drivers/net/irda/Makefile
>> > index 5d20fde..d82e1e3 100644
>> > --- a/drivers/net/irda/Makefile
>> > +++ b/drivers/net/irda/Makefile
>> > @@ -21,6 +21,7 @@ obj-$(CONFIG_MCS_FIR) ? ? ? ? += mcs7780.o
>> > ?obj-$(CONFIG_AU1000_FIR) ? ? ? += au1k_ir.o
>> > ?# SIR drivers
>> > ?obj-$(CONFIG_IRTTY_SIR) ? ? ? ? ? ? ? ?+= irtty-sir.o ?sir-dev.o
>> > +obj-$(CONFIG_BFIN_SIR) ? ? ? ? += bfin_sir.o
>> > ?# dongle drivers for SIR drivers
>> > ?obj-$(CONFIG_ESI_DONGLE) ? ? ? += esi-sir.o
>> > ?obj-$(CONFIG_TEKRAM_DONGLE) ? ?+= tekram-sir.o
>> > diff --git a/drivers/net/irda/bfin_sir.c b/drivers/net/irda/bfin_sir.c
>> > new file mode 100644
>> > index 0000000..38584cc
>> > --- /dev/null
>> > +++ b/drivers/net/irda/bfin_sir.c
>> > @@ -0,0 +1,814 @@
>> > +/*
>> > + * Blackfin Infra-red Driver
>> > + *
>> > + * Copyright 2006-2009 Analog Devices Inc.
>> > + *
>> > + * Enter bugs at http://blackfin.uclinux.org/
>> > + *
>> > + * Licensed under the GPL-2 or later.
>> > + *
>> > + */
>> > +#include "bfin_sir.h"
>> > +
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > +#define DMA_SIR_RX_XCNT ? ? ? ?10
>> > +#define DMA_SIR_RX_YCNT ? ? ? ?(PAGE_SIZE / DMA_SIR_RX_XCNT)
>> > +#define DMA_SIR_RX_FLUSH_JIFS ?(HZ * 4 / 250)
>> > +#endif
>> > +
>> > +#if ANOMALY_05000447
>> > +static int max_rate = 57600;
>> > +#else
>> > +static int max_rate = 115200;
>> > +#endif
>> > +
>> > +static void turnaround_delay(unsigned long last_jif, int mtt)
>> > +{
>> > + ? ? ? long ticks;
>> > +
>> > + ? ? ? mtt = mtt < 10000 ? 10000 : mtt;
>> > + ? ? ? ticks = 1 + mtt / (USEC_PER_SEC / HZ);
>> > + ? ? ? schedule_timeout_uninterruptible(ticks);
>> > +}
>> > +
>> > +static void __devinit bfin_sir_init_ports(struct bfin_sir_port *sp,
>> > struct platform_device *pdev)
>> > +{
>> > + ? ? ? int i;
>> > + ? ? ? struct resource *res;
>> > +
>> > + ? ? ? for (i = 0; i < pdev->num_resources; i++) {
>> > + ? ? ? ? ? ? ? res = &pdev->resource[i];
>> > + ? ? ? ? ? ? ? switch (res->flags) {
>> > + ? ? ? ? ? ? ? case IORESOURCE_MEM:
>> > + ? ? ? ? ? ? ? ? ? ? ? sp->membase ? = (void __iomem *)res->start;
>> > + ? ? ? ? ? ? ? ? ? ? ? break;
>> > + ? ? ? ? ? ? ? case IORESOURCE_IRQ:
>> > + ? ? ? ? ? ? ? ? ? ? ? sp->irq = res->start;
>> > + ? ? ? ? ? ? ? ? ? ? ? break;
>> > + ? ? ? ? ? ? ? case IORESOURCE_DMA:
>> > + ? ? ? ? ? ? ? ? ? ? ? sp->rx_dma_channel = res->start;
>> > + ? ? ? ? ? ? ? ? ? ? ? sp->tx_dma_channel = res->end;
>> > + ? ? ? ? ? ? ? ? ? ? ? break;
>> > + ? ? ? ? ? ? ? default:
>> > + ? ? ? ? ? ? ? ? ? ? ? break;
>> > + ? ? ? ? ? ? ? }
>> > + ? ? ? }
>> > +
>> > + ? ? ? sp->clk = get_sclk();
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > + ? ? ? sp->tx_done ? ? ? ?= 1;
>> > + ? ? ? init_timer(&(sp->rx_dma_timer));
>> > +#endif
>> > +}
>> > +
>> > +static void bfin_sir_stop_tx(struct bfin_sir_port *port)
>> > +{
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > + ? ? ? disable_dma(port->tx_dma_channel);
>> > +#endif
>> > +
>> > + ? ? ? while (!(SIR_UART_GET_LSR(port) & THRE)) {
>> > + ? ? ? ? ? ? ? cpu_relax();
>> > + ? ? ? ? ? ? ? continue;
>> > + ? ? ? }
>> > +
>> > + ? ? ? SIR_UART_STOP_TX(port);
>> > +}
>> > +
>> > +static void bfin_sir_enable_tx(struct bfin_sir_port *port)
>> > +{
>> > + ? ? ? SIR_UART_ENABLE_TX(port);
>> > +}
>> > +
>> > +static void bfin_sir_stop_rx(struct bfin_sir_port *port)
>> > +{
>> > + ? ? ? SIR_UART_STOP_RX(port);
>> > +}
>> > +
>> > +static void bfin_sir_enable_rx(struct bfin_sir_port *port)
>> > +{
>> > + ? ? ? SIR_UART_ENABLE_RX(port);
>> > +}
>> > +
>> > +static int bfin_sir_set_speed(struct bfin_sir_port *port, int speed)
>> > +{
>> > + ? ? ? int ret = -EINVAL;
>> > + ? ? ? unsigned int quot;
>> > + ? ? ? unsigned short val, lsr, lcr;
>> > + ? ? ? static int utime;
>> > + ? ? ? int count = 10;
>> > +
>> > + ? ? ? lcr = WLS(8);
>> > +
>> > + ? ? ? switch (speed) {
>> > + ? ? ? case 9600:
>> > + ? ? ? case 19200:
>> > + ? ? ? case 38400:
>> > + ? ? ? case 57600:
>> > + ? ? ? case 115200:
>> > +
>> > + ? ? ? ? ? ? ? quot = (port->clk + (8 * speed)) / (16 * speed)\
>> > + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? - ANOMALY_05000230;
>> > +
>> > + ? ? ? ? ? ? ? do {
>> > + ? ? ? ? ? ? ? ? ? ? ? udelay(utime);
>> > + ? ? ? ? ? ? ? ? ? ? ? lsr = SIR_UART_GET_LSR(port);
>> > + ? ? ? ? ? ? ? } while (!(lsr & TEMT) && count--);
>> > +
>> > + ? ? ? ? ? ? ? /* The useconds for 1 bits to transmit */
>> > + ? ? ? ? ? ? ? utime = 1000000 / speed + 1;
>> > +
>> > + ? ? ? ? ? ? ? /* Clear UCEN bit to reset the UART state machine
>> > + ? ? ? ? ? ? ? ?* and control registers
>> > + ? ? ? ? ? ? ? ?*/
>> > + ? ? ? ? ? ? ? val = SIR_UART_GET_GCTL(port);
>> > + ? ? ? ? ? ? ? val &= ~UCEN;
>> > + ? ? ? ? ? ? ? SIR_UART_PUT_GCTL(port, val);
>> > +
>> > + ? ? ? ? ? ? ? /* Set DLAB in LCR to Access THR RBR IER */
>> > + ? ? ? ? ? ? ? SIR_UART_SET_DLAB(port);
>> > + ? ? ? ? ? ? ? SSYNC();
>> > +
>> > + ? ? ? ? ? ? ? SIR_UART_PUT_DLL(port, quot & 0xFF);
>> > + ? ? ? ? ? ? ? SIR_UART_PUT_DLH(port, (quot >> 8) & 0xFF);
>> > + ? ? ? ? ? ? ? SSYNC();
>> > +
>> > + ? ? ? ? ? ? ? /* Clear DLAB in LCR */
>> > + ? ? ? ? ? ? ? SIR_UART_CLEAR_DLAB(port);
>> > + ? ? ? ? ? ? ? SSYNC();
>> > +
>> > + ? ? ? ? ? ? ? SIR_UART_PUT_LCR(port, lcr);
>> > +
>> > + ? ? ? ? ? ? ? val = SIR_UART_GET_GCTL(port);
>> > + ? ? ? ? ? ? ? val |= UCEN;
>> > + ? ? ? ? ? ? ? SIR_UART_PUT_GCTL(port, val);
>> > +
>> > + ? ? ? ? ? ? ? ret = 0;
>> > + ? ? ? ? ? ? ? break;
>> > + ? ? ? default:
>> > + ? ? ? ? ? ? ? printk(KERN_WARNING "bfin_sir: Invalid speed %d\n",
>> > speed);
>> > + ? ? ? ? ? ? ? break;
>> > + ? ? ? }
>> > +
>> > + ? ? ? val = SIR_UART_GET_GCTL(port);
>> > + ? ? ? /* If not add the 'RPOLC', we can't catch the receive interrupt.
>> > + ? ? ? ?* It's related with the HW layout and the IR transiver.
>> > + ? ? ? ?*/
>> > + ? ? ? val |= IREN | RPOLC;
>> > + ? ? ? SIR_UART_PUT_GCTL(port, val);
>> > + ? ? ? return ret;
>> > +}
>> > +
>> > +static int bfin_sir_is_receiving(struct net_device *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > +
>> > + ? ? ? if (!(SIR_UART_GET_IER(port) & ERBFI))
>> > + ? ? ? ? ? ? ? return 0;
>> > + ? ? ? return self->rx_buff.state != OUTSIDE_FRAME;
>> > +}
>> > +
>> > +#ifdef CONFIG_SIR_BFIN_PIO
>> > +static void bfin_sir_tx_chars(struct net_device *dev)
>> > +{
>> > + ? ? ? unsigned int chr;
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > +
>> > + ? ? ? if (self->tx_buff.len != 0) {
>> > + ? ? ? ? ? ? ? chr = *(self->tx_buff.data);
>> > + ? ? ? ? ? ? ? SIR_UART_PUT_CHAR(port, chr);
>> > + ? ? ? ? ? ? ? self->tx_buff.data++;
>> > + ? ? ? ? ? ? ? self->tx_buff.len--;
>> > + ? ? ? } else {
>> > + ? ? ? ? ? ? ? self->stats.tx_packets++;
>> > + ? ? ? ? ? ? ? self->stats.tx_bytes += self->tx_buff.data -
>> > self->tx_buff.head;
>> > + ? ? ? ? ? ? ? if (self->newspeed) {
>> > + ? ? ? ? ? ? ? ? ? ? ? bfin_sir_set_speed(port, self->newspeed);
>> > + ? ? ? ? ? ? ? ? ? ? ? self->speed = self->newspeed;
>> > + ? ? ? ? ? ? ? ? ? ? ? self->newspeed = 0;
>> > + ? ? ? ? ? ? ? }
>> > + ? ? ? ? ? ? ? bfin_sir_stop_tx(port);
>> > + ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
>> > + ? ? ? ? ? ? ? /* I'm hungry! */
>> > + ? ? ? ? ? ? ? netif_wake_queue(dev);
>> > + ? ? ? }
>> > +}
>> > +
>> > +static void bfin_sir_rx_chars(struct net_device *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > + ? ? ? unsigned char ch;
>> > +
>> > + ? ? ? SIR_UART_CLEAR_LSR(port);
>> > + ? ? ? ch = SIR_UART_GET_CHAR(port);
>> > + ? ? ? async_unwrap_char(dev, &self->stats, &self->rx_buff, ch);
>> > + ? ? ? dev->last_rx = jiffies;
>> > +}
>> > +
>> > +static irqreturn_t bfin_sir_rx_int(int irq, void *dev_id)
>> > +{
>> > + ? ? ? struct net_device *dev = dev_id;
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > +
>> > + ? ? ? spin_lock(&self->lock);
>> > + ? ? ? while ((SIR_UART_GET_LSR(port) & DR))
>> > + ? ? ? ? ? ? ? bfin_sir_rx_chars(dev);
>> > + ? ? ? spin_unlock(&self->lock);
>> > +
>> > + ? ? ? return IRQ_HANDLED;
>> > +}
>> > +
>> > +static irqreturn_t bfin_sir_tx_int(int irq, void *dev_id)
>> > +{
>> > + ? ? ? struct net_device *dev = dev_id;
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > +
>> > + ? ? ? spin_lock(&self->lock);
>> > + ? ? ? if (SIR_UART_GET_LSR(port) & THRE)
>> > + ? ? ? ? ? ? ? bfin_sir_tx_chars(dev);
>> > + ? ? ? spin_unlock(&self->lock);
>> > +
>> > + ? ? ? return IRQ_HANDLED;
>> > +}
>> > +#endif /* CONFIG_SIR_BFIN_PIO */
>> > +
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > +static void bfin_sir_dma_tx_chars(struct net_device *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > +
>> > + ? ? ? if (!port->tx_done)
>> > + ? ? ? ? ? ? ? return;
>> > + ? ? ? port->tx_done = 0;
>> > +
>> > + ? ? ? if (self->tx_buff.len == 0) {
>> > + ? ? ? ? ? ? ? self->stats.tx_packets++;
>> > + ? ? ? ? ? ? ? if (self->newspeed) {
>> > + ? ? ? ? ? ? ? ? ? ? ? bfin_sir_set_speed(port, self->newspeed);
>> > + ? ? ? ? ? ? ? ? ? ? ? self->speed = self->newspeed;
>> > + ? ? ? ? ? ? ? ? ? ? ? self->newspeed = 0;
>> > + ? ? ? ? ? ? ? }
>> > + ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
>> > + ? ? ? ? ? ? ? port->tx_done = 1;
>> > + ? ? ? ? ? ? ? netif_wake_queue(dev);
>> > + ? ? ? ? ? ? ? return;
>> > + ? ? ? }
>> > +
>> > + ? ? ? blackfin_dcache_flush_range((unsigned long)(self->tx_buff.data),
>> > + ? ? ? ? ? ? ? (unsigned long)(self->tx_buff.data+self->tx_buff.len));
>> > + ? ? ? set_dma_config(port->tx_dma_channel,
>> > + ? ? ? ? ? ? ? set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
>> > + ? ? ? ? ? ? ? ? ? ? ? INTR_ON_BUF, DIMENSION_LINEAR, DATA_SIZE_8,
>> > + ? ? ? ? ? ? ? ? ? ? ? DMA_SYNC_RESTART));
>> > + ? ? ? set_dma_start_addr(port->tx_dma_channel,
>> > + ? ? ? ? ? ? ? (unsigned long)(self->tx_buff.data));
>> > + ? ? ? set_dma_x_count(port->tx_dma_channel, self->tx_buff.len);
>> > + ? ? ? set_dma_x_modify(port->tx_dma_channel, 1);
>> > + ? ? ? enable_dma(port->tx_dma_channel);
>> > +}
>> > +
>> > +static irqreturn_t bfin_sir_dma_tx_int(int irq, void *dev_id)
>> > +{
>> > + ? ? ? struct net_device *dev = dev_id;
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > +
>> > + ? ? ? spin_lock(&self->lock);
>> > + ? ? ? if (!(get_dma_curr_irqstat(port->tx_dma_channel) & DMA_RUN)) {
>> > + ? ? ? ? ? ? ? clear_dma_irqstat(port->tx_dma_channel);
>> > + ? ? ? ? ? ? ? bfin_sir_stop_tx(port);
>> > +
>> > + ? ? ? ? ? ? ? self->stats.tx_packets++;
>> > + ? ? ? ? ? ? ? self->stats.tx_bytes += self->tx_buff.len;
>> > + ? ? ? ? ? ? ? self->tx_buff.len = 0;
>> > + ? ? ? ? ? ? ? if (self->newspeed) {
>> > + ? ? ? ? ? ? ? ? ? ? ? bfin_sir_set_speed(port, self->newspeed);
>> > + ? ? ? ? ? ? ? ? ? ? ? self->speed = self->newspeed;
>> > + ? ? ? ? ? ? ? ? ? ? ? self->newspeed = 0;
>> > + ? ? ? ? ? ? ? }
>> > + ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
>> > + ? ? ? ? ? ? ? /* I'm hungry! */
>> > + ? ? ? ? ? ? ? netif_wake_queue(dev);
>> > + ? ? ? ? ? ? ? port->tx_done = 1;
>> > + ? ? ? }
>> > + ? ? ? spin_unlock(&self->lock);
>> > +
>> > + ? ? ? return IRQ_HANDLED;
>> > +}
>> > +
>> > +static void bfin_sir_dma_rx_chars(struct net_device *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > + ? ? ? int i;
>> > +
>> > + ? ? ? SIR_UART_CLEAR_LSR(port);
>> > +
>> > + ? ? ? for (i = port->rx_dma_buf.head; i < port->rx_dma_buf.tail; i++)
>> > + ? ? ? ? ? ? ? async_unwrap_char(dev, &self->stats, &self->rx_buff,
>> > port->rx_dma_buf.buf[i]);
>> > +}
>> > +
>> > +void bfin_sir_rx_dma_timeout(struct net_device *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > + ? ? ? int x_pos, pos;
>> > + ? ? ? unsigned long flags;
>> > +
>> > + ? ? ? spin_lock_irqsave(&self->lock, flags);
>> > + ? ? ? x_pos = DMA_SIR_RX_XCNT -
>> > get_dma_curr_xcount(port->rx_dma_channel);
>> > + ? ? ? if (x_pos == DMA_SIR_RX_XCNT)
>> > + ? ? ? ? ? ? ? x_pos = 0;
>> > +
>> > + ? ? ? pos = port->rx_dma_nrows * DMA_SIR_RX_XCNT + x_pos;
>> > +
>> > + ? ? ? if (pos > port->rx_dma_buf.tail) {
>> > + ? ? ? ? ? ? ? port->rx_dma_buf.tail = pos;
>> > + ? ? ? ? ? ? ? bfin_sir_dma_rx_chars(dev);
>> > + ? ? ? ? ? ? ? port->rx_dma_buf.head = port->rx_dma_buf.tail;
>> > + ? ? ? }
>> > + ? ? ? spin_unlock_irqrestore(&self->lock, flags);
>> > +}
>> > +
>> > +static irqreturn_t bfin_sir_dma_rx_int(int irq, void *dev_id)
>> > +{
>> > + ? ? ? struct net_device *dev = dev_id;
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > + ? ? ? unsigned short irqstat;
>> > +
>> > + ? ? ? spin_lock(&self->lock);
>> > +
>> > + ? ? ? port->rx_dma_nrows++;
>> > + ? ? ? port->rx_dma_buf.tail = DMA_SIR_RX_XCNT * port->rx_dma_nrows;
>> > + ? ? ? bfin_sir_dma_rx_chars(dev);
>> > + ? ? ? if (port->rx_dma_nrows >= DMA_SIR_RX_YCNT) {
>> > + ? ? ? ? ? ? ? port->rx_dma_nrows = 0;
>> > + ? ? ? ? ? ? ? port->rx_dma_buf.tail = 0;
>> > + ? ? ? }
>> > + ? ? ? port->rx_dma_buf.head = port->rx_dma_buf.tail;
>> > +
>> > + ? ? ? irqstat = get_dma_curr_irqstat(port->rx_dma_channel);
>> > + ? ? ? clear_dma_irqstat(port->rx_dma_channel);
>> > + ? ? ? spin_unlock(&self->lock);
>> > +
>> > + ? ? ? mod_timer(&port->rx_dma_timer, jiffies + DMA_SIR_RX_FLUSH_JIFS);
>> > + ? ? ? return IRQ_HANDLED;
>> > +}
>> > +#endif /* CONFIG_SIR_BFIN_DMA */
>> > +
>> > +static int bfin_sir_startup(struct bfin_sir_port *port, struct
>> > net_device *dev)
>> > +{
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > + ? ? ? dma_addr_t dma_handle;
>> > +#endif /* CONFIG_SIR_BFIN_DMA */
>> > +
>> > + ? ? ? if (request_dma(port->rx_dma_channel, "BFIN_UART_RX") < 0) {
>> > + ? ? ? ? ? ? ? dev_warn(&dev->dev, "Unable to attach SIR RX DMA
>> > channel\n");
>> > + ? ? ? ? ? ? ? return -EBUSY;
>> > + ? ? ? }
>> > +
>> > + ? ? ? if (request_dma(port->tx_dma_channel, "BFIN_UART_TX") < 0) {
>> > + ? ? ? ? ? ? ? dev_warn(&dev->dev, "Unable to attach SIR TX DMA
>> > channel\n");
>> > + ? ? ? ? ? ? ? free_dma(port->rx_dma_channel);
>> > + ? ? ? ? ? ? ? return -EBUSY;
>> > + ? ? ? }
>> > +
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > +
>> > + ? ? ? set_dma_callback(port->rx_dma_channel, bfin_sir_dma_rx_int,
>> > dev);
>> > + ? ? ? set_dma_callback(port->tx_dma_channel, bfin_sir_dma_tx_int,
>> > dev);
>> > +
>> > + ? ? ? port->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL,
>> > PAGE_SIZE, &dma_handle, GFP_DMA);
>> > + ? ? ? port->rx_dma_buf.head = 0;
>> > + ? ? ? port->rx_dma_buf.tail = 0;
>> > + ? ? ? port->rx_dma_nrows = 0;
>> > +
>> > + ? ? ? set_dma_config(port->rx_dma_channel,
>> > + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? set_bfin_dma_config(DIR_WRITE,
>> > DMA_FLOW_AUTO,
>> > +
>> > INTR_ON_ROW, DIMENSION_2D,
>> > +
>> > DATA_SIZE_8, DMA_SYNC_RESTART));
>> > + ? ? ? set_dma_x_count(port->rx_dma_channel, DMA_SIR_RX_XCNT);
>> > + ? ? ? set_dma_x_modify(port->rx_dma_channel, 1);
>> > + ? ? ? set_dma_y_count(port->rx_dma_channel, DMA_SIR_RX_YCNT);
>> > + ? ? ? set_dma_y_modify(port->rx_dma_channel, 1);
>> > + ? ? ? set_dma_start_addr(port->rx_dma_channel, (unsigned
>> > long)port->rx_dma_buf.buf);
>> > + ? ? ? enable_dma(port->rx_dma_channel);
>> > +
>> > + ? ? ? port->rx_dma_timer.data = (unsigned long)(dev);
>> > + ? ? ? port->rx_dma_timer.function = (void *)bfin_sir_rx_dma_timeout;
>> > +
>> > +#else
>> > +
>> > + ? ? ? if (request_irq(port->irq, bfin_sir_rx_int, IRQF_DISABLED,
>> > "BFIN_SIR_RX", dev)) {
>> > + ? ? ? ? ? ? ? dev_warn(&dev->dev, "Unable to attach SIR RX
>> > interrupt\n");
>> > + ? ? ? ? ? ? ? return -EBUSY;
>> > + ? ? ? }
>> > +
>> > + ? ? ? if (request_irq(port->irq+1, bfin_sir_tx_int, IRQF_DISABLED,
>> > "BFIN_SIR_TX", dev)) {
>> > + ? ? ? ? ? ? ? dev_warn(&dev->dev, "Unable to attach SIR TX
>> > interrupt\n");
>> > + ? ? ? ? ? ? ? free_irq(port->irq, dev);
>> > + ? ? ? ? ? ? ? return -EBUSY;
>> > + ? ? ? }
>> > +#endif
>> > +
>> > + ? ? ? return 0;
>> > +}
>> > +
>> > +static void bfin_sir_shutdown(struct bfin_sir_port *port, struct
>> > net_device *dev)
>> > +{
>> > + ? ? ? unsigned short val;
>> > +
>> > + ? ? ? bfin_sir_stop_rx(port);
>> > + ? ? ? SIR_UART_DISABLE_INTS(port);
>> > +
>> > + ? ? ? val = SIR_UART_GET_GCTL(port);
>> > + ? ? ? val &= ~(UCEN | IREN | RPOLC);
>> > + ? ? ? SIR_UART_PUT_GCTL(port, val);
>> > +
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > + ? ? ? disable_dma(port->tx_dma_channel);
>> > + ? ? ? disable_dma(port->rx_dma_channel);
>> > + ? ? ? del_timer(&(port->rx_dma_timer));
>> > + ? ? ? dma_free_coherent(NULL, PAGE_SIZE, port->rx_dma_buf.buf, 0);
>> > +#else
>> > + ? ? ? free_irq(port->irq+1, dev);
>> > + ? ? ? free_irq(port->irq, dev);
>> > +#endif
>> > + ? ? ? free_dma(port->tx_dma_channel);
>> > + ? ? ? free_dma(port->rx_dma_channel);
>> > +}
>> > +
>> > +#ifdef CONFIG_PM
>> > +static int bfin_sir_suspend(struct platform_device *pdev, pm_message_t
>> > state)
>> > +{
>> > + ? ? ? struct bfin_sir_port *sir_port;
>> > + ? ? ? struct net_device *dev;
>> > + ? ? ? struct bfin_sir_self *self;
>> > +
>> > + ? ? ? sir_port = platform_get_drvdata(pdev);
>> > + ? ? ? if (!sir_port)
>> > + ? ? ? ? ? ? ? return 0;
>> > +
>> > + ? ? ? dev = sir_port->dev;
>> > + ? ? ? self = netdev_priv(dev);
>> > + ? ? ? if (self->open) {
>> > + ? ? ? ? ? ? ? flush_work(&self->work);
>> > + ? ? ? ? ? ? ? bfin_sir_shutdown(self->sir_port, dev);
>> > + ? ? ? ? ? ? ? netif_device_detach(dev);
>> > + ? ? ? }
>> > +
>> > + ? ? ? return 0;
>> > +}
>> > +static int bfin_sir_resume(struct platform_device *pdev)
>> > +{
>> > + ? ? ? struct bfin_sir_port *sir_port;
>> > + ? ? ? struct net_device *dev;
>> > + ? ? ? struct bfin_sir_self *self;
>> > + ? ? ? struct bfin_sir_port *port;
>> > +
>> > + ? ? ? sir_port = platform_get_drvdata(pdev);
>> > + ? ? ? if (!sir_port)
>> > + ? ? ? ? ? ? ? return 0;
>> > +
>> > + ? ? ? dev = sir_port->dev;
>> > + ? ? ? self = netdev_priv(dev);
>> > + ? ? ? port = self->sir_port;
>> > + ? ? ? if (self->open) {
>> > + ? ? ? ? ? ? ? if (self->newspeed) {
>> > + ? ? ? ? ? ? ? ? ? ? ? self->speed = self->newspeed;
>> > + ? ? ? ? ? ? ? ? ? ? ? self->newspeed = 0;
>> > + ? ? ? ? ? ? ? }
>> > + ? ? ? ? ? ? ? bfin_sir_startup(port, dev);
>> > + ? ? ? ? ? ? ? bfin_sir_set_speed(port, 9600);
>> > + ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
>> > + ? ? ? ? ? ? ? netif_device_attach(dev);
>> > + ? ? ? }
>> > + ? ? ? return 0;
>> > +}
>> > +#else
>> > +#define bfin_sir_suspend ? NULL
>> > +#define bfin_sir_resume ? ?NULL
>> > +#endif
>> > +
>> > +static void bfin_sir_send_work(struct work_struct *work)
>> > +{
>> > + ? ? ? struct bfin_sir_self ?*self = container_of(work, struct
>> > bfin_sir_self, work);
>> > + ? ? ? struct net_device *dev = self->sir_port->dev;
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > + ? ? ? unsigned short val;
>> > + ? ? ? int tx_cnt = 10;
>> > +
>> > + ? ? ? while (bfin_sir_is_receiving(dev) && --tx_cnt)
>> > + ? ? ? ? ? ? ? turnaround_delay(dev->last_rx, self->mtt);
>> > +
>> > + ? ? ? bfin_sir_stop_rx(port);
>> > +
>> > + ? ? ? /* To avoid losting RX interrupt, we reset IR function before
>> > + ? ? ? ?* sending data. We also can set the speed, which will
>> > + ? ? ? ?* reset all the UART.
>> > + ? ? ? ?*/
>> > + ? ? ? val = SIR_UART_GET_GCTL(port);
>> > + ? ? ? val &= ~(IREN | RPOLC);
>> > + ? ? ? SIR_UART_PUT_GCTL(port, val);
>> > + ? ? ? SSYNC();
>> > + ? ? ? val |= IREN | RPOLC;
>> > + ? ? ? SIR_UART_PUT_GCTL(port, val);
>> > + ? ? ? SSYNC();
>> > + ? ? ? /* bfin_sir_set_speed(port, self->speed); */
>> > +
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > + ? ? ? bfin_sir_dma_tx_chars(dev);
>> > +#endif
>> > + ? ? ? bfin_sir_enable_tx(port);
>> > + ? ? ? dev->trans_start = jiffies;
>> > +}
>> > +
>> > +static int bfin_sir_hard_xmit(struct sk_buff *skb, struct net_device
>> > *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? int speed = irda_get_next_speed(skb);
>> > +
>> > + ? ? ? netif_stop_queue(dev);
>> > +
>> > + ? ? ? self->mtt = irda_get_mtt(skb);
>> > +
>> > + ? ? ? if (speed != self->speed && speed != -1)
>> > + ? ? ? ? ? ? ? self->newspeed = speed;
>> > +
>> > + ? ? ? self->tx_buff.data = self->tx_buff.head;
>> > + ? ? ? if (skb->len == 0)
>> > + ? ? ? ? ? ? ? self->tx_buff.len = 0;
>> > + ? ? ? else
>> > + ? ? ? ? ? ? ? self->tx_buff.len = async_wrap_skb(skb,
>> > self->tx_buff.data, self->tx_buff.truesize);
>> > +
>> > + ? ? ? schedule_work(&self->work);
>> > + ? ? ? dev_kfree_skb(skb);
>> > +
>> > + ? ? ? return 0;
>> > +}
>> > +
>> > +static int bfin_sir_ioctl(struct net_device *dev, struct ifreq *ifreq,
>> > int cmd)
>> > +{
>> > + ? ? ? struct if_irda_req *rq = (struct if_irda_req *)ifreq;
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > + ? ? ? int ret = 0;
>> > +
>> > + ? ? ? switch (cmd) {
>> > + ? ? ? case SIOCSBANDWIDTH:
>> > + ? ? ? ? ? ? ? if (capable(CAP_NET_ADMIN)) {
>> > + ? ? ? ? ? ? ? ? ? ? ? if (self->open) {
>> > + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ret = bfin_sir_set_speed(port,
>> > rq->ifr_baudrate);
>> > + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? bfin_sir_enable_rx(port);
>> > + ? ? ? ? ? ? ? ? ? ? ? } else {
>> > + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? dev_warn(&dev->dev, "SIOCSBANDWIDTH:
>> > !netif_running\n");
>> > + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ret = 0;
>> > + ? ? ? ? ? ? ? ? ? ? ? }
>> > + ? ? ? ? ? ? ? }
>> > + ? ? ? ? ? ? ? break;
>> > +
>> > + ? ? ? case SIOCSMEDIABUSY:
>> > + ? ? ? ? ? ? ? ret = -EPERM;
>> > + ? ? ? ? ? ? ? if (capable(CAP_NET_ADMIN)) {
>> > + ? ? ? ? ? ? ? ? ? ? ? irda_device_set_media_busy(dev, TRUE);
>> > + ? ? ? ? ? ? ? ? ? ? ? ret = 0;
>> > + ? ? ? ? ? ? ? }
>> > + ? ? ? ? ? ? ? break;
>> > +
>> > + ? ? ? case SIOCGRECEIVING:
>> > + ? ? ? ? ? ? ? rq->ifr_receiving = bfin_sir_is_receiving(dev);
>> > + ? ? ? ? ? ? ? break;
>> > +
>> > + ? ? ? default:
>> > + ? ? ? ? ? ? ? ret = -EOPNOTSUPP;
>> > + ? ? ? ? ? ? ? break;
>> > + ? ? ? }
>> > +
>> > + ? ? ? return ret;
>> > +}
>> > +
>> > +static struct net_device_stats *bfin_sir_stats(struct net_device *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > +
>> > + ? ? ? return &self->stats;
>> > +}
>> > +
>> > +static int bfin_sir_open(struct net_device *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > + ? ? ? struct bfin_sir_port *port = self->sir_port;
>> > + ? ? ? int err = -ENOMEM;
>> > +
>> > + ? ? ? self->newspeed = 0;
>> > + ? ? ? self->speed = 9600;
>> > +
>> > + ? ? ? spin_lock_init(&self->lock);
>> > +
>> > + ? ? ? err = bfin_sir_startup(port, dev);
>> > + ? ? ? if (err)
>> > + ? ? ? ? ? ? ? goto err_startup;
>> > +
>> > + ? ? ? bfin_sir_set_speed(port, 9600);
>> > +
>> > + ? ? ? self->irlap = irlap_open(dev, &self->qos, DRIVER_NAME);
>> > + ? ? ? if (!self->irlap)
>> > + ? ? ? ? ? ? ? goto err_irlap;
>> > +
>> > + ? ? ? INIT_WORK(&self->work, bfin_sir_send_work);
>> > +
>> > + ? ? ? /*
>> > + ? ? ? ?* Now enable the interrupt then start the queue
>> > + ? ? ? ?*/
>> > + ? ? ? self->open = 1;
>> > + ? ? ? bfin_sir_enable_rx(port);
>> > +
>> > + ? ? ? netif_start_queue(dev);
>> > +
>> > + ? ? ? return 0;
>> > +
>> > +err_irlap:
>> > + ? ? ? self->open = 0;
>> > + ? ? ? bfin_sir_shutdown(port, dev);
>> > +err_startup:
>> > + ? ? ? return err;
>> > +}
>> > +
>> > +static int bfin_sir_stop(struct net_device *dev)
>> > +{
>> > + ? ? ? struct bfin_sir_self *self = netdev_priv(dev);
>> > +
>> > + ? ? ? flush_work(&self->work);
>> > + ? ? ? bfin_sir_shutdown(self->sir_port, dev);
>> > +
>> > + ? ? ? if (self->rxskb) {
>> > + ? ? ? ? ? ? ? dev_kfree_skb(self->rxskb);
>> > + ? ? ? ? ? ? ? self->rxskb = NULL;
>> > + ? ? ? }
>> > +
>> > + ? ? ? /* Stop IrLAP */
>> > + ? ? ? if (self->irlap) {
>> > + ? ? ? ? ? ? ? irlap_close(self->irlap);
>> > + ? ? ? ? ? ? ? self->irlap = NULL;
>> > + ? ? ? }
>> > +
>> > + ? ? ? netif_stop_queue(dev);
>> > + ? ? ? self->open = 0;
>> > +
>> > + ? ? ? return 0;
>> > +}
>> > +
>> > +static int bfin_sir_init_iobuf(iobuff_t *io, int size)
>> > +{
>> > + ? ? ? io->head = kmalloc(size, GFP_KERNEL);
>> > + ? ? ? if (!io->head)
>> > + ? ? ? ? ? ? ? return -ENOMEM;
>> > + ? ? ? io->truesize = size;
>> > + ? ? ? io->in_frame = FALSE;
>> > + ? ? ? io->state ? ?= OUTSIDE_FRAME;
>> > + ? ? ? io->data ? ? = io->head;
>> > + ? ? ? return 0;
>> > +}
>> > +
>> > +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>> > +{
>> > + ? ? ? struct net_device *dev;
>> > + ? ? ? struct bfin_sir_self *self;
>> > + ? ? ? unsigned int baudrate_mask;
>> > + ? ? ? struct bfin_sir_port *sir_port;
>> > + ? ? ? int err;
>> > +
>> > + ? ? ? err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>> > + ? ? ? if (err)
>> > + ? ? ? ? ? ? ? return err;
>> > +
>> > + ? ? ? err = -ENOMEM;
>> > + ? ? ? sir_port = kmalloc(sizeof(*sir_port), GFP_KERNEL);
>> > + ? ? ? if (!sir_port)
>> > + ? ? ? ? ? ? ? goto err_mem_0;
>> > +
>> > + ? ? ? bfin_sir_init_ports(sir_port, pdev);
>> > +
>> > + ? ? ? dev = alloc_irdadev(sizeof(*self));
>> > + ? ? ? if (!dev)
>> > + ? ? ? ? ? ? ? goto err_mem_1;
>> > +
>> > + ? ? ? self = netdev_priv(dev);
>> > + ? ? ? self->dev = &pdev->dev;
>> > + ? ? ? self->sir_port = sir_port;
>> > + ? ? ? sir_port->dev = dev;
>> > +
>> > + ? ? ? err = bfin_sir_init_iobuf(&self->rx_buff, IRDA_SKB_MAX_MTU);
>> > + ? ? ? if (err)
>> > + ? ? ? ? ? ? ? goto err_mem_2;
>> > + ? ? ? err = bfin_sir_init_iobuf(&self->tx_buff, IRDA_SIR_MAX_FRAME);
>> > + ? ? ? if (err)
>> > + ? ? ? ? ? ? ? goto err_mem_3;
>> > +
>> > + ? ? ? dev->hard_start_xmit = bfin_sir_hard_xmit;
>> > + ? ? ? dev->open ? ? ? ? ? ?= bfin_sir_open;
>> > + ? ? ? dev->stop ? ? ? ? ? ?= bfin_sir_stop;
>> > + ? ? ? dev->do_ioctl ? ? ? ?= bfin_sir_ioctl;
>> > + ? ? ? dev->get_stats ? ? ? = bfin_sir_stats;
>> > + ? ? ? dev->irq ? ? ? ? ? ? = sir_port->irq;
>> > +
>> > + ? ? ? irda_init_max_qos_capabilies(&self->qos);
>> > +
>> > + ? ? ? baudrate_mask = IR_9600;
>> > +
>> > + ? ? ? switch (max_rate) {
>> > + ? ? ? case 115200:
>> > + ? ? ? ? ? ? ? baudrate_mask |= IR_115200;
>> > + ? ? ? case 57600:
>> > + ? ? ? ? ? ? ? baudrate_mask |= IR_57600;
>> > + ? ? ? case 38400:
>> > + ? ? ? ? ? ? ? baudrate_mask |= IR_38400;
>> > + ? ? ? case 19200:
>> > + ? ? ? ? ? ? ? baudrate_mask |= IR_19200;
>> > + ? ? ? case 9600:
>> > + ? ? ? ? ? ? ? break;
>> > + ? ? ? default:
>> > + ? ? ? ? ? ? ? printk(KERN_WARNING "bfin_sir: Invalid maximum baud
>> > rate, using 9600\n");
>> > + ? ? ? }
>> > +
>> > + ? ? ? self->qos.baud_rate.bits &= baudrate_mask;
>> > +
>> > + ? ? ? self->qos.min_turn_time.bits = 1; /* 10 ms or more */
>> > +
>> > + ? ? ? irda_qos_bits_to_value(&self->qos);
>> > +
>> > + ? ? ? err = register_netdev(dev);
>> > +
>> > + ? ? ? if (err) {
>> > + ? ? ? ? ? ? ? kfree(self->tx_buff.head);
>> > +err_mem_3:
>> > + ? ? ? ? ? ? ? kfree(self->rx_buff.head);
>> > +err_mem_2:
>> > + ? ? ? ? ? ? ? free_netdev(dev);
>> > +err_mem_1:
>> > + ? ? ? ? ? ? ? kfree(sir_port);
>> > +err_mem_0:
>> > + ? ? ? ? ? ? ? peripheral_free_list(per[pdev->id]);
>> > + ? ? ? } else
>> > + ? ? ? ? ? ? ? platform_set_drvdata(pdev, sir_port);
>> > +
>> > + ? ? ? return err;
>> > +}
>> > +
>> > +static int __devexit bfin_sir_remove(struct platform_device *pdev)
>> > +{
>> > + ? ? ? struct bfin_sir_port *sir_port;
>> > + ? ? ? struct net_device *dev = NULL;
>> > + ? ? ? struct bfin_sir_self *self;
>> > +
>> > + ? ? ? sir_port = platform_get_drvdata(pdev);
>> > + ? ? ? if (!sir_port)
>> > + ? ? ? ? ? ? ? return 0;
>> > + ? ? ? dev = sir_port->dev;
>> > + ? ? ? self = netdev_priv(dev);
>> > + ? ? ? unregister_netdev(dev);
>> > + ? ? ? kfree(self->tx_buff.head);
>> > + ? ? ? kfree(self->rx_buff.head);
>> > + ? ? ? free_netdev(dev);
>> > + ? ? ? kfree(sir_port);
>> > + ? ? ? platform_set_drvdata(pdev, NULL);
>> > +
>> > + ? ? ? return 0;
>> > +}
>> > +
>> > +static struct platform_driver bfin_ir_driver = {
>> > + ? ? ? .probe ? = bfin_sir_probe,
>> > + ? ? ? .remove ?= __devexit_p(bfin_sir_remove),
>> > + ? ? ? .suspend = bfin_sir_suspend,
>> > + ? ? ? .resume ?= bfin_sir_resume,
>> > + ? ? ? .driver ?= {
>> > + ? ? ? ? ? ? ? .name = DRIVER_NAME,
>> > + ? ? ? },
>> > +};
>> > +
>> > +static int __init bfin_sir_init(void)
>> > +{
>> > + ? ? ? return platform_driver_register(&bfin_ir_driver);
>> > +}
>> > +
>> > +static void __exit bfin_sir_exit(void)
>> > +{
>> > + ? ? ? platform_driver_unregister(&bfin_ir_driver);
>> > +}
>> > +
>> > +module_init(bfin_sir_init);
>> > +module_exit(bfin_sir_exit);
>> > +
>> > +module_param(max_rate, int, 0);
>> > +MODULE_PARM_DESC(max_rate, "Maximum baud rate (115200, 57600, 38400,
>> > 19200, 9600)");
>> > +
>> > +MODULE_AUTHOR("Graf Yang <[email protected]>");
>> > +MODULE_DESCRIPTION("Blackfin IrDA driver");
>> > +MODULE_LICENSE("GPL");
>> > diff --git a/drivers/net/irda/bfin_sir.h b/drivers/net/irda/bfin_sir.h
>> > new file mode 100644
>> > index 0000000..a723257
>> > --- /dev/null
>> > +++ b/drivers/net/irda/bfin_sir.h
>> > @@ -0,0 +1,147 @@
>> > +/*
>> > + * Blackfin Infra-red Driver
>> > + *
>> > + * Copyright 2006-2009 Analog Devices Inc.
>> > + *
>> > + * Enter bugs at http://blackfin.uclinux.org/
>> > + *
>> > + * Licensed under the GPL-2 or later.
>> > + *
>> > + */
>> > +
>> > +#include <linux/serial.h>
>> > +#include <linux/module.h>
>> > +#include <linux/netdevice.h>
>> > +#include <linux/interrupt.h>
>> > +#include <linux/delay.h>
>> > +#include <linux/platform_device.h>
>> > +#include <linux/dma-mapping.h>
>> > +
>> > +#include <net/irda/irda.h>
>> > +#include <net/irda/wrapper.h>
>> > +#include <net/irda/irda_device.h>
>> > +
>> > +#include <asm/irq.h>
>> > +#include <asm/cacheflush.h>
>> > +#include <asm/dma.h>
>> > +#include <asm/portmux.h>
>> > +
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > +struct dma_rx_buf {
>> > + ? ? ? char *buf;
>> > + ? ? ? int head;
>> > + ? ? ? int tail;
>> > +};
>> > +#endif
>> > +
>> > +struct bfin_sir_port {
>> > + ? ? ? unsigned char __iomem ? *membase;
>> > + ? ? ? unsigned int ? ? ? ? ? ?irq;
>> > + ? ? ? unsigned int ? ? ? ? ? ?lsr;
>> > + ? ? ? unsigned long ? ? ? ? ? clk;
>> > + ? ? ? struct net_device ? ? ? *dev;
>> > +#ifdef CONFIG_SIR_BFIN_DMA
>> > + ? ? ? int ? ? ? ? ? ? ? ? ? ? tx_done;
>> > + ? ? ? struct dma_rx_buf ? ? ? rx_dma_buf;
>> > + ? ? ? struct timer_list ? ? ? rx_dma_timer;
>> > + ? ? ? int ? ? ? ? ? ? ? ? ? ? rx_dma_nrows;
>> > +#endif
>> > + ? ? ? unsigned int ? ? ? ? ? ?tx_dma_channel;
>> > + ? ? ? unsigned int ? ? ? ? ? ?rx_dma_channel;
>> > +};
>> > +
>> > +struct bfin_sir_port_res {
>> > + ? ? ? unsigned long ? base_addr;
>> > + ? ? ? int ? ? ? ? ? ? irq;
>> > + ? ? ? unsigned int ? ?rx_dma_channel;
>> > + ? ? ? unsigned int ? ?tx_dma_channel;
>> > +};
>> > +
>> > +struct bfin_sir_self {
>> > + ? ? ? struct bfin_sir_port ? ?*sir_port;
>> > + ? ? ? spinlock_t ? ? ? ? ? ? ?lock;
>> > + ? ? ? unsigned int ? ? ? ? ? ?open;
>> > + ? ? ? int ? ? ? ? ? ? ? ? ? ? speed;
>> > + ? ? ? int ? ? ? ? ? ? ? ? ? ? newspeed;
>> > +
>> > + ? ? ? struct sk_buff ? ? ? ? ?*txskb;
>> > + ? ? ? struct sk_buff ? ? ? ? ?*rxskb;
>> > + ? ? ? struct net_device_stats stats;
>> > + ? ? ? struct device ? ? ? ? ? *dev;
>> > + ? ? ? struct irlap_cb ? ? ? ? *irlap;
>> > + ? ? ? struct qos_info ? ? ? ? qos;
>> > +
>> > + ? ? ? iobuff_t ? ? ? ? ? ? ? ?tx_buff;
>> > + ? ? ? iobuff_t ? ? ? ? ? ? ? ?rx_buff;
>> > +
>> > + ? ? ? struct work_struct ? ? ?work;
>> > + ? ? ? int ? ? ? ? ? ? ? ? ? ? mtt;
>> > +};
>> > +
>> > +#define DRIVER_NAME "bfin_sir"
>> > +
>> > +#define SIR_UART_GET_CHAR(port) ? ?bfin_read16((port)->membase +
>> > OFFSET_RBR)
>> > +#define SIR_UART_GET_DLL(port) ? ? bfin_read16((port)->membase +
>> > OFFSET_DLL)
>> > +#define SIR_UART_GET_DLH(port) ? ? bfin_read16((port)->membase +
>> > OFFSET_DLH)
>> > +#define SIR_UART_GET_LCR(port) ? ? bfin_read16((port)->membase +
>> > OFFSET_LCR)
>> > +#define SIR_UART_GET_GCTL(port) ? ?bfin_read16((port)->membase +
>> > OFFSET_GCTL)
>> > +
>> > +#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase +
>> > OFFSET_THR), v)
>> > +#define SIR_UART_PUT_DLL(port, v) ?bfin_write16(((port)->membase +
>> > OFFSET_DLL), v)
>> > +#define SIR_UART_PUT_DLH(port, v) ?bfin_write16(((port)->membase +
>> > OFFSET_DLH), v)
>> > +#define SIR_UART_PUT_LCR(port, v) ?bfin_write16(((port)->membase +
>> > OFFSET_LCR), v)
>> > +#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase +
>> > OFFSET_GCTL), v)
>> > +
>> > +#ifdef CONFIG_BF54x
>> > +#define SIR_UART_GET_LSR(port) ? ? bfin_read16((port)->membase +
>> > OFFSET_LSR)
>> > +#define SIR_UART_GET_IER(port) ? ? bfin_read16((port)->membase +
>> > OFFSET_IER_SET)
>> > +#define SIR_UART_SET_IER(port, v) ?bfin_write16(((port)->membase +
>> > OFFSET_IER_SET), v)
>> > +#define SIR_UART_CLEAR_IER(port, v) bfin_write16(((port)->membase +
>> > OFFSET_IER_CLEAR), v)
>> > +#define SIR_UART_PUT_LSR(port, v) ?bfin_write16(((port)->membase +
>> > OFFSET_LSR), v)
>> > +#define SIR_UART_CLEAR_LSR(port) ? bfin_write16(((port)->membase +
>> > OFFSET_LSR), -1)
>> > +
>> > +#define SIR_UART_SET_DLAB(port)
>> > +#define SIR_UART_CLEAR_DLAB(port)
>> > +
>> > +#define SIR_UART_ENABLE_INTS(port, v) SIR_UART_SET_IER(port, v)
>> > +#define SIR_UART_DISABLE_INTS(port) ? SIR_UART_CLEAR_IER(port, 0xF)
>> > +#define SIR_UART_STOP_TX(port) ? ? do { SIR_UART_PUT_LSR(port, TFI);
>> > SIR_UART_CLEAR_IER(port, ETBEI); } while (0)
>> > +#define SIR_UART_ENABLE_TX(port) ? do { SIR_UART_SET_IER(port, ETBEI);
>> > } while (0)
>> > +#define SIR_UART_STOP_RX(port) ? ? do { SIR_UART_CLEAR_IER(port,
>> > ERBFI); } while (0)
>> > +#define SIR_UART_ENABLE_RX(port) ? do { SIR_UART_SET_IER(port, ERBFI);
>> > } while (0)
>> > +#else
>> > +
>> > +#define SIR_UART_GET_IIR(port) ? ? bfin_read16((port)->membase +
>> > OFFSET_IIR)
>> > +#define SIR_UART_GET_IER(port) ? ? bfin_read16((port)->membase +
>> > OFFSET_IER)
>> > +#define SIR_UART_PUT_IER(port, v) ?bfin_write16(((port)->membase +
>> > OFFSET_IER), v)
>> > +
>> > +#define SIR_UART_SET_DLAB(port) ? ?do { SIR_UART_PUT_LCR(port,
>> > SIR_UART_GET_LCR(port) | DLAB); } while (0)
>> > +#define SIR_UART_CLEAR_DLAB(port) ?do { SIR_UART_PUT_LCR(port,
>> > SIR_UART_GET_LCR(port) & ~DLAB); } while (0)
>> > +
>> > +#define SIR_UART_ENABLE_INTS(port, v) SIR_UART_PUT_IER(port, v)
>> > +#define SIR_UART_DISABLE_INTS(port) ? SIR_UART_PUT_IER(port, 0)
>> > +#define SIR_UART_STOP_TX(port) ? ? do { SIR_UART_PUT_IER(port,
>> > SIR_UART_GET_IER(port) & ~ETBEI); } while (0)
>> > +#define SIR_UART_ENABLE_TX(port) ? do { SIR_UART_PUT_IER(port,
>> > SIR_UART_GET_IER(port) | ETBEI); } while (0)
>> > +#define SIR_UART_STOP_RX(port) ? ? do { SIR_UART_PUT_IER(port,
>> > SIR_UART_GET_IER(port) & ~ERBFI); } while (0)
>> > +#define SIR_UART_ENABLE_RX(port) ? do { SIR_UART_PUT_IER(port,
>> > SIR_UART_GET_IER(port) | ERBFI); } while (0)
>> > +
>> > +static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
>> > +{
>> > + ? ? ? unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
>> > + ? ? ? port->lsr |= (lsr & (BI|FE|PE|OE));
>> > + ? ? ? return lsr | port->lsr;
>> > +}
>> > +
>> > +static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
>> > +{
>> > + ? ? ? port->lsr = 0;
>> > + ? ? ? bfin_read16(port->membase + OFFSET_LSR);
>> > +}
>> > +#endif
>> > +
>> > +static const unsigned short per[][3] = {
>> > + ? ? ? {P_UART0_RX, P_UART0_TX, 0},
>> > + ? ? ? {P_UART1_RX, P_UART1_TX, 0},
>> > + ? ? ? {P_UART2_RX, P_UART2_TX, 0},
>> > + ? ? ? {P_UART3_RX, P_UART3_TX, 0},
>> > +};
>> > --
>> > 1.6.1
>> > --
>> > To unsubscribe from this list: send the line "unsubscribe linux-kernel"
>> > in
>> > the body of a message to [email protected]
>> > More majordomo info at ?http://vger.kernel.org/majordomo-info.html
>> > Please read the FAQ at ?http://www.tux.org/lkml/
>> >
>
>
>
> --
> -Graff
>
On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger <[email protected]> wrote:
> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>> +{
>> + struct net_device *dev;
>> + struct bfin_sir_self *self;
>> + unsigned int baudrate_mask;
>> + struct bfin_sir_port *sir_port;
>> + int err;
>> +
>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>
> what if pdev->id is set to 12512 ?
The pdev->id is defined in board files, for example, uart0 should be 0.
>
>> + switch (max_rate) {
>> + default:
>> + printk(KERN_WARNING "bfin_sir: Invalid maximum baud rate, using 9600\n");
>
> dev_warn(&dev->dev,....) ?
Here the netdev has not been registered.
> -mike
>
--
-Graff
On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
> On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
>> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
>>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>>> +{
>>> + struct net_device *dev;
>>> + struct bfin_sir_self *self;
>>> + unsigned int baudrate_mask;
>>> + struct bfin_sir_port *sir_port;
>>> + int err;
>>> +
>>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>>
>> what if pdev->id is set to 12512 ?
>
> The pdev->id is defined in board files, for example, uart0 should be 0.
so ? what's to stop the user from setting it to 12415 ? the driver
must sanity check these things. you can never assume platform dev
resources always have valid pointers and valid values.
>>> + switch (max_rate) {
>>> + default:
>>> + printk(KERN_WARNING "bfin_sir: Invalid maximum baud rate, using 9600\n");
>>
>> dev_warn(&dev->dev,....) ?
>
> Here the netdev has not been registered.
then use pdev->dev ?
-mike
On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
> >>> +{
> >>> + struct net_device *dev;
> >>> + struct bfin_sir_self *self;
> >>> + unsigned int baudrate_mask;
> >>> + struct bfin_sir_port *sir_port;
> >>> + int err;
> >>> +
> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
> >>
> >> what if pdev->id is set to 12512 ?
> >
> > The pdev->id is defined in board files, for example, uart0 should be 0.
>
> so ? what's to stop the user from setting it to 12415 ? the driver
> must sanity check these things. you can never assume platform dev
> resources always have valid pointers and valid values.
How about to limit the pdev->id to be 0,1,2,3 ?
I can extend the per to be
static const unsigned short per[][4] = {
{P_UART0_RX, P_UART0_TX, 0, 0},
{P_UART1_RX, P_UART1_TX, 0, 1},
{P_UART2_RX, P_UART2_TX, 0, 2},
{P_UART3_RX, P_UART3_TX, 0, 3},
};
then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
per[pdev->id][3] == pdev->id)
>
> >>> + switch (max_rate) {
> >>> + default:
> >>> + printk(KERN_WARNING "bfin_sir: Invalid maximum baud rate, using 9600\n");
> >>
> >> dev_warn(&dev->dev,....) ?
> >
> > Here the netdev has not been registered.
>
> then use pdev->dev ?
Don't it seem strange to mixed use dev_warn(&dev->dev, ...) and
dev_warn(&pdev->dev, ...) ? And printk is enough.
> -mike
On Thu, Mar 12, 2009 at 00:17, gyang wrote:
> On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
>> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
>> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
>> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
>> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>> >>> +{
>> >>> + struct net_device *dev;
>> >>> + struct bfin_sir_self *self;
>> >>> + unsigned int baudrate_mask;
>> >>> + struct bfin_sir_port *sir_port;
>> >>> + int err;
>> >>> +
>> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>> >>
>> >> what if pdev->id is set to 12512 ?
>> >
>> > The pdev->id is defined in board files, for example, uart0 should be 0.
>>
>> so ? what's to stop the user from setting it to 12415 ? the driver
>> must sanity check these things. you can never assume platform dev
>> resources always have valid pointers and valid values.
>
> How about to limit the pdev->id to be 0,1,2,3 ?
> I can extend the per to be
> static const unsigned short per[][4] = {
> {P_UART0_RX, P_UART0_TX, 0, 0},
> {P_UART1_RX, P_UART1_TX, 0, 1},
> {P_UART2_RX, P_UART2_TX, 0, 2},
> {P_UART3_RX, P_UART3_TX, 0, 3},
> };
>
> then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
> per[pdev->id][3] == pdev->id)
the last check is redundant. the first two should be added.
>> >>> + switch (max_rate) {
>> >>> + default:
>> >>> + printk(KERN_WARNING "bfin_sir: Invalid maximum baud rate, using 9600\n");
>> >>
>> >> dev_warn(&dev->dev,....) ?
>> >
>> > Here the netdev has not been registered.
>>
>> then use pdev->dev ?
>
> Don't it seem strange to mixed use dev_warn(&dev->dev, ...) and
> dev_warn(&pdev->dev, ...) ?
not really
> And printk is enough.
printk() makes sense when a dev is not available. we have a dev here,
so the dev_*() funcs should be used.
-mike
On Thu, 2009-03-12 at 00:23 -0400, Mike Frysinger wrote:
> On Thu, Mar 12, 2009 at 00:17, gyang wrote:
> > On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
> >> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
> >> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
> >> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
> >> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
> >> >>> +{
> >> >>> + struct net_device *dev;
> >> >>> + struct bfin_sir_self *self;
> >> >>> + unsigned int baudrate_mask;
> >> >>> + struct bfin_sir_port *sir_port;
> >> >>> + int err;
> >> >>> +
> >> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
> >> >>
> >> >> what if pdev->id is set to 12512 ?
> >> >
> >> > The pdev->id is defined in board files, for example, uart0 should be 0.
> >>
> >> so ? what's to stop the user from setting it to 12415 ? the driver
> >> must sanity check these things. you can never assume platform dev
> >> resources always have valid pointers and valid values.
> >
> > How about to limit the pdev->id to be 0,1,2,3 ?
> > I can extend the per to be
> > static const unsigned short per[][4] = {
> > {P_UART0_RX, P_UART0_TX, 0, 0},
> > {P_UART1_RX, P_UART1_TX, 0, 1},
> > {P_UART2_RX, P_UART2_TX, 0, 2},
> > {P_UART3_RX, P_UART3_TX, 0, 3},
> > };
> >
> > then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
> > per[pdev->id][3] == pdev->id)
>
> the last check is redundant. the first two should be added.
I'm afraid of some cases such as uart0 uses id 1, will cause driver not
work, and not any warning message.
>
> >> >>> + switch (max_rate) {
> >> >>> + default:
> >> >>> + printk(KERN_WARNING "bfin_sir: Invalid maximum baud rate, using 9600\n");
> >> >>
> >> >> dev_warn(&dev->dev,....) ?
> >> >
> >> > Here the netdev has not been registered.
> >>
> >> then use pdev->dev ?
> >
> > Don't it seem strange to mixed use dev_warn(&dev->dev, ...) and
> > dev_warn(&pdev->dev, ...) ?
>
> not really
>
> > And printk is enough.
>
> printk() makes sense when a dev is not available. we have a dev here,
> so the dev_*() funcs should be used.
> -mike
On Thu, Mar 12, 2009 at 00:30, gyang wrote:
> On Thu, 2009-03-12 at 00:23 -0400, Mike Frysinger wrote:
>> On Thu, Mar 12, 2009 at 00:17, gyang wrote:
>> > On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
>> >> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
>> >> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
>> >> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
>> >> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>> >> >>> +{
>> >> >>> + struct net_device *dev;
>> >> >>> + struct bfin_sir_self *self;
>> >> >>> + unsigned int baudrate_mask;
>> >> >>> + struct bfin_sir_port *sir_port;
>> >> >>> + int err;
>> >> >>> +
>> >> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>> >> >>
>> >> >> what if pdev->id is set to 12512 ?
>> >> >
>> >> > The pdev->id is defined in board files, for example, uart0 should be 0.
>> >>
>> >> so ? what's to stop the user from setting it to 12415 ? the driver
>> >> must sanity check these things. you can never assume platform dev
>> >> resources always have valid pointers and valid values.
>> >
>> > How about to limit the pdev->id to be 0,1,2,3 ?
>> > I can extend the per to be
>> > static const unsigned short per[][4] = {
>> > {P_UART0_RX, P_UART0_TX, 0, 0},
>> > {P_UART1_RX, P_UART1_TX, 0, 1},
>> > {P_UART2_RX, P_UART2_TX, 0, 2},
>> > {P_UART3_RX, P_UART3_TX, 0, 3},
>> > };
>> >
>> > then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
>> > per[pdev->id][3] == pdev->id)
>>
>> the last check is redundant. the first two should be added.
>
> I'm afraid of some cases such as uart0 uses id 1, will cause driver not
> work, and not any warning message.
then the call to peripheral request would fail as expected
-mike
On Thu, 2009-03-12 at 00:34 -0400, Mike Frysinger wrote:
> On Thu, Mar 12, 2009 at 00:30, gyang wrote:
> > On Thu, 2009-03-12 at 00:23 -0400, Mike Frysinger wrote:
> >> On Thu, Mar 12, 2009 at 00:17, gyang wrote:
> >> > On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
> >> >> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
> >> >> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
> >> >> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
> >> >> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
> >> >> >>> +{
> >> >> >>> + struct net_device *dev;
> >> >> >>> + struct bfin_sir_self *self;
> >> >> >>> + unsigned int baudrate_mask;
> >> >> >>> + struct bfin_sir_port *sir_port;
> >> >> >>> + int err;
> >> >> >>> +
> >> >> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
> >> >> >>
> >> >> >> what if pdev->id is set to 12512 ?
> >> >> >
> >> >> > The pdev->id is defined in board files, for example, uart0 should be 0.
> >> >>
> >> >> so ? what's to stop the user from setting it to 12415 ? the driver
> >> >> must sanity check these things. you can never assume platform dev
> >> >> resources always have valid pointers and valid values.
> >> >
> >> > How about to limit the pdev->id to be 0,1,2,3 ?
> >> > I can extend the per to be
> >> > static const unsigned short per[][4] = {
> >> > {P_UART0_RX, P_UART0_TX, 0, 0},
> >> > {P_UART1_RX, P_UART1_TX, 0, 1},
> >> > {P_UART2_RX, P_UART2_TX, 0, 2},
> >> > {P_UART3_RX, P_UART3_TX, 0, 3},
> >> > };
> >> >
> >> > then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
> >> > per[pdev->id][3] == pdev->id)
> >>
> >> the last check is redundant. the first two should be added.
> >
> > I'm afraid of some cases such as uart0 uses id 1, will cause driver not
> > work, and not any warning message.
>
> then the call to peripheral request would fail as expected
For example, user want to enable irda on uart2 for bf548, he use id 0
for uart2. In these case, peripheral request may not fail, but driver
not work.
> -mike
On Thu, Mar 12, 2009 at 00:48, gyang wrote:
> On Thu, 2009-03-12 at 00:34 -0400, Mike Frysinger wrote:
>> On Thu, Mar 12, 2009 at 00:30, gyang wrote:
>> > On Thu, 2009-03-12 at 00:23 -0400, Mike Frysinger wrote:
>> >> On Thu, Mar 12, 2009 at 00:17, gyang wrote:
>> >> > On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
>> >> >> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
>> >> >> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
>> >> >> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
>> >> >> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>> >> >> >>> +{
>> >> >> >>> + struct net_device *dev;
>> >> >> >>> + struct bfin_sir_self *self;
>> >> >> >>> + unsigned int baudrate_mask;
>> >> >> >>> + struct bfin_sir_port *sir_port;
>> >> >> >>> + int err;
>> >> >> >>> +
>> >> >> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>> >> >> >>
>> >> >> >> what if pdev->id is set to 12512 ?
>> >> >> >
>> >> >> > The pdev->id is defined in board files, for example, uart0 should be 0.
>> >> >>
>> >> >> so ? what's to stop the user from setting it to 12415 ? the driver
>> >> >> must sanity check these things. you can never assume platform dev
>> >> >> resources always have valid pointers and valid values.
>> >> >
>> >> > How about to limit the pdev->id to be 0,1,2,3 ?
>> >> > I can extend the per to be
>> >> > static const unsigned short per[][4] = {
>> >> > {P_UART0_RX, P_UART0_TX, 0, 0},
>> >> > {P_UART1_RX, P_UART1_TX, 0, 1},
>> >> > {P_UART2_RX, P_UART2_TX, 0, 2},
>> >> > {P_UART3_RX, P_UART3_TX, 0, 3},
>> >> > };
>> >> >
>> >> > then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
>> >> > per[pdev->id][3] == pdev->id)
>> >>
>> >> the last check is redundant. the first two should be added.
>> >
>> > I'm afraid of some cases such as uart0 uses id 1, will cause driver not
>> > work, and not any warning message.
>>
>> then the call to peripheral request would fail as expected
>
> For example, user want to enable irda on uart2 for bf548, he use id 0
> for uart2. In these case, peripheral request may not fail, but driver
> not work.
the id is wrong then. if they want uart2, then they should use id 2.
-mike
On Thu, Mar 12, 2009 at 12:59 PM, Mike Frysinger <[email protected]> wrote:
> On Thu, Mar 12, 2009 at 00:48, gyang wrote:
>> On Thu, 2009-03-12 at 00:34 -0400, Mike Frysinger wrote:
>>> On Thu, Mar 12, 2009 at 00:30, gyang wrote:
>>> > On Thu, 2009-03-12 at 00:23 -0400, Mike Frysinger wrote:
>>> >> On Thu, Mar 12, 2009 at 00:17, gyang wrote:
>>> >> > On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
>>> >> >> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
>>> >> >> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
>>> >> >> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
>>> >> >> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>>> >> >> >>> +{
>>> >> >> >>> + struct net_device *dev;
>>> >> >> >>> + struct bfin_sir_self *self;
>>> >> >> >>> + unsigned int baudrate_mask;
>>> >> >> >>> + struct bfin_sir_port *sir_port;
>>> >> >> >>> + int err;
>>> >> >> >>> +
>>> >> >> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>>> >> >> >>
>>> >> >> >> what if pdev->id is set to 12512 ?
>>> >> >> >
>>> >> >> > The pdev->id is defined in board files, for example, uart0 should be 0.
>>> >> >>
>>> >> >> so ? what's to stop the user from setting it to 12415 ? the driver
>>> >> >> must sanity check these things. you can never assume platform dev
>>> >> >> resources always have valid pointers and valid values.
>>> >> >
>>> >> > How about to limit the pdev->id to be 0,1,2,3 ?
>>> >> > I can extend the per to be
>>> >> > static const unsigned short per[][4] = {
>>> >> > {P_UART0_RX, P_UART0_TX, 0, 0},
>>> >> > {P_UART1_RX, P_UART1_TX, 0, 1},
>>> >> > {P_UART2_RX, P_UART2_TX, 0, 2},
>>> >> > {P_UART3_RX, P_UART3_TX, 0, 3},
>>> >> > };
>>> >> >
>>> >> > then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
>>> >> > per[pdev->id][3] == pdev->id)
>>> >>
>>> >> the last check is redundant. the first two should be added.
>>> >
>>> > I'm afraid of some cases such as uart0 uses id 1, will cause driver not
>>> > work, and not any warning message.
>>>
>>> then the call to peripheral request would fail as expected
>>
>> For example, user want to enable irda on uart2 for bf548, he use id 0
>> for uart2. In these case, peripheral request may not fail, but driver
>> not work.
>
> the id is wrong then. if they want uart2, then they should use id 2.
> -mike
>
Such wrong case may existed for common users, and should be
prohibited. Driver need make sanity check to prevent it.
--
-Graff
On Thu, Mar 12, 2009 at 01:55, graff yang wrote:
> On Thu, Mar 12, 2009 at 12:59 PM, Mike Frysinger wrote:
>> On Thu, Mar 12, 2009 at 00:48, gyang wrote:
>>> On Thu, 2009-03-12 at 00:34 -0400, Mike Frysinger wrote:
>>>> On Thu, Mar 12, 2009 at 00:30, gyang wrote:
>>>> > On Thu, 2009-03-12 at 00:23 -0400, Mike Frysinger wrote:
>>>> >> On Thu, Mar 12, 2009 at 00:17, gyang wrote:
>>>> >> > On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
>>>> >> >> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
>>>> >> >> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
>>>> >> >> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
>>>> >> >> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>>>> >> >> >>> +{
>>>> >> >> >>> + struct net_device *dev;
>>>> >> >> >>> + struct bfin_sir_self *self;
>>>> >> >> >>> + unsigned int baudrate_mask;
>>>> >> >> >>> + struct bfin_sir_port *sir_port;
>>>> >> >> >>> + int err;
>>>> >> >> >>> +
>>>> >> >> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>>>> >> >> >>
>>>> >> >> >> what if pdev->id is set to 12512 ?
>>>> >> >> >
>>>> >> >> > The pdev->id is defined in board files, for example, uart0 should be 0.
>>>> >> >>
>>>> >> >> so ? what's to stop the user from setting it to 12415 ? the driver
>>>> >> >> must sanity check these things. you can never assume platform dev
>>>> >> >> resources always have valid pointers and valid values.
>>>> >> >
>>>> >> > How about to limit the pdev->id to be 0,1,2,3 ?
>>>> >> > I can extend the per to be
>>>> >> > static const unsigned short per[][4] = {
>>>> >> > {P_UART0_RX, P_UART0_TX, 0, 0},
>>>> >> > {P_UART1_RX, P_UART1_TX, 0, 1},
>>>> >> > {P_UART2_RX, P_UART2_TX, 0, 2},
>>>> >> > {P_UART3_RX, P_UART3_TX, 0, 3},
>>>> >> > };
>>>> >> >
>>>> >> > then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
>>>> >> > per[pdev->id][3] == pdev->id)
>>>> >>
>>>> >> the last check is redundant. the first two should be added.
>>>> >
>>>> > I'm afraid of some cases such as uart0 uses id 1, will cause driver not
>>>> > work, and not any warning message.
>>>>
>>>> then the call to peripheral request would fail as expected
>>>
>>> For example, user want to enable irda on uart2 for bf548, he use id 0
>>> for uart2. In these case, peripheral request may not fail, but driver
>>> not work.
>>
>> the id is wrong then. if they want uart2, then they should use id 2.
>
> Such wrong case may existed for common users, and should be
> prohibited. Driver need make sanity check to prevent it.
i dont know what you're talking about. if the platform resource uses
id of 2, then they want uart2 which means irda2. the sanity check is
already in place because the peripheral_request() will fail when it
attempts to claim the pins of uart2 but the uart driver has already
been enabled for it.
-mike
On Thu, Mar 12, 2009 at 2:24 PM, Mike Frysinger <[email protected]> wrote:
> On Thu, Mar 12, 2009 at 01:55, graff yang wrote:
>> On Thu, Mar 12, 2009 at 12:59 PM, Mike Frysinger wrote:
>>> On Thu, Mar 12, 2009 at 00:48, gyang wrote:
>>>> On Thu, 2009-03-12 at 00:34 -0400, Mike Frysinger wrote:
>>>>> On Thu, Mar 12, 2009 at 00:30, gyang wrote:
>>>>> > On Thu, 2009-03-12 at 00:23 -0400, Mike Frysinger wrote:
>>>>> >> On Thu, Mar 12, 2009 at 00:17, gyang wrote:
>>>>> >> > On Wed, 2009-03-11 at 06:43 -0400, Mike Frysinger wrote:
>>>>> >> >> On Wed, Mar 11, 2009 at 05:56, graff yang wrote:
>>>>> >> >> > On Wed, Mar 11, 2009 at 3:57 PM, Mike Frysinger wrote:
>>>>> >> >> >> On Wed, Mar 11, 2009 at 03:29, <[email protected]> wrote:
>>>>> >> >> >>> +static int __devinit bfin_sir_probe(struct platform_device *pdev)
>>>>> >> >> >>> +{
>>>>> >> >> >>> + struct net_device *dev;
>>>>> >> >> >>> + struct bfin_sir_self *self;
>>>>> >> >> >>> + unsigned int baudrate_mask;
>>>>> >> >> >>> + struct bfin_sir_port *sir_port;
>>>>> >> >> >>> + int err;
>>>>> >> >> >>> +
>>>>> >> >> >>> + err = peripheral_request_list(per[pdev->id], DRIVER_NAME);
>>>>> >> >> >>
>>>>> >> >> >> what if pdev->id is set to 12512 ?
>>>>> >> >> >
>>>>> >> >> > The pdev->id is defined in board files, for example, uart0 should be 0.
>>>>> >> >>
>>>>> >> >> so ? what's to stop the user from setting it to 12415 ? the driver
>>>>> >> >> must sanity check these things. you can never assume platform dev
>>>>> >> >> resources always have valid pointers and valid values.
>>>>> >> >
>>>>> >> > How about to limit the pdev->id to be 0,1,2,3 ?
>>>>> >> > I can extend the per to be
>>>>> >> > static const unsigned short per[][4] = {
>>>>> >> > {P_UART0_RX, P_UART0_TX, 0, 0},
>>>>> >> > {P_UART1_RX, P_UART1_TX, 0, 1},
>>>>> >> > {P_UART2_RX, P_UART2_TX, 0, 2},
>>>>> >> > {P_UART3_RX, P_UART3_TX, 0, 3},
>>>>> >> > };
>>>>> >> >
>>>>> >> > then check (pdev->id >= 0 && pdev->id < ARRAY_SIZE(per) &&
>>>>> >> > per[pdev->id][3] == pdev->id)
>>>>> >>
>>>>> >> the last check is redundant. the first two should be added.
>>>>> >
>>>>> > I'm afraid of some cases such as uart0 uses id 1, will cause driver not
>>>>> > work, and not any warning message.
>>>>>
>>>>> then the call to peripheral request would fail as expected
>>>>
>>>> For example, user want to enable irda on uart2 for bf548, he use id 0
>>>> for uart2. In these case, peripheral request may not fail, but driver
>>>> not work.
>>>
>>> the id is wrong then. if they want uart2, then they should use id 2.
>>
>> Such wrong case may existed for common users, and should be
>> prohibited. Driver need make sanity check to prevent it.
>
> i dont know what you're talking about. if the platform resource uses
> id of 2, then they want uart2 which means irda2.
The X of irdaX is determined by the order of calling register_netdev().
It will be irda0 for the first registered irda device, in spite of the pdev->id.
Because you argued that user can use any id for pdev->id, I think I not only
need limit them to be 0~3, but also need keep them in right order, or else,
driver may be fail.
It is easy for driver to check that, and safe for users.
> the sanity check is
> already in place because the peripheral_request() will fail when it
> attempts to claim the pins of uart2 but the uart driver has already
> been enabled for it.
> -mike
>
--
-Graff