LinuxLists.cc - [BUG?] ISA-PnP and 3c509 NIC won't work together

2001-02-03 18:02:59

Subject: [BUG?] ISA-PnP and 3c509 NIC won't work together

Card 1 'TER1411:TERRATEC SOUNDSYSTEM BASE 1' PnP version 1.0 Product version 1.1
Logical device 0 'ADS7180:Unknown'
Supported registers 0x2
Device is not active
Resources 0
Priority preferred
Port 0x220-0x220, align 0x1f, size 0x10, 16-bit address decoding
Port 0x388-0x388, align 0x7, size 0x4, 16-bit address decoding
Port 0x530-0x530, align 0x7, size 0x10, 16-bit address decoding
IRQ 5 High-Edge
DMA 1 8-bit byte-count type-A
DMA 3 8-bit byte-count type-A
Alternate resources 0:1
Priority acceptable
Port 0x220-0x240, align 0x1f, size 0x10, 16-bit address decoding
Port 0x388-0x388, align 0x7, size 0x4, 16-bit address decoding
Port 0x530-0x530, align 0xf, size 0x10, 16-bit address decoding
IRQ 5,7 High-Edge
DMA 0,1,3 8-bit byte-count type-A
DMA 0,1,3 8-bit byte-count type-A
Alternate resources 0:2
Priority functional
Port 0x220-0x280, align 0x1f, size 0x10, 16-bit address decoding
Port 0x388-0x3b8, align 0x7, size 0x4, 16-bit address decoding
Port 0x500-0x560, align 0xf, size 0x10, 16-bit address decoding
IRQ 5,7,10 High-Edge
DMA 0,1,3 8-bit byte-count type-A
DMA 0,1,3 8-bit byte-count type-A
Alternate resources 0:3
Priority functional
Port 0x220-0x280, align 0x1f, size 0x10, 16-bit address decoding
Port 0x388-0x3b8, align 0x7, size 0x4, 16-bit address decoding
Port 0x500-0x620, align 0xf, size 0x10, 16-bit address decoding
IRQ 5,7,10,11 High-Edge
DMA 0,1,3 8-bit byte-count type-A
DMA <none> 8-bit byte-count type-A
Alternate resources 0:4
Priority functional
Port 0x220-0x280, align 0x1f, size 0x10, 16-bit address decoding
Port 0x388-0x3b8, align 0x7, size 0x4, 16-bit address decoding
Port 0x500-0x620, align 0xf, size 0x10, 16-bit address decoding
IRQ 5,7,2/9,10,11,15 High-Edge
DMA 0,1,3 8-bit byte-count type-A
DMA <none> 8-bit byte-count type-A
Logical device 1 'ADS7181:Unknown'
Supported registers 0x2
Compatible device PNPb006
Device is not active
Resources 0
Priority preferred
Port 0x330-0x330, align 0xf, size 0x2, 16-bit address decoding
IRQ 2/9 High-Edge
Alternate resources 0:1
Priority acceptable
Port 0x300-0x330, align 0xf, size 0x2, 16-bit address decoding
IRQ 2/9 High-Edge
Alternate resources 0:2
Priority functional
Port 0x300-0x330, align 0xf, size 0x2, 16-bit address decoding
IRQ 2/9,10,11,15 High-Edge
Logical device 2 'ADS7182:Unknown'
Supported registers 0x2
Compatible device PNPb02f
Device is not active
Resources 0
Priority preferred
Port 0x200-0x200, align 0x7, size 0x8, 16-bit address decoding
Alternate resources 0:1
Priority acceptable
Port 0x200-0x208, align 0x7, size 0x8, 16-bit address decoding
Logical device 3 'TER2211:Unknown'
Supported registers 0x2
Device is not active
Resources 0
Priority preferred
Port 0x590-0x590, align 0x7, size 0x8, 16-bit address decoding
Alternate resources 0:1
Priority acceptable
Port 0x590-0x5a8, align 0x7, size 0x8, 16-bit address decoding
Alternate resources 0:2
Priority functional
Port 0x590-0x5c8, align 0x7, size 0x8, 16-bit address decoding

Attachments:

isapnp (3.38 kB)

2001-02-03 20:39:08

by Viktor Rosenfeld

[permalink] [raw]

Subject: Re: [BUG?] ISA-PnP and 3c509 NIC won't work together

Jeff Garzik wrote:
>
> Victor,
>
> Can you respond to your recently-sent linux-kernel e-mail, and provide
> the output of 'dmesg' after all your experiments? 'dmesg' program
> displays the kernel logging buffer, and should give us much additional
> information.

Of course, here it comes. BTW, ISA-PnP left out and 3c509 compiled as
module won't do it either. I get the same error message about parm_io.
As you can see, only when I have ISA-PnP left out and 3c509 compiled-in,
the NIC is recognized.

- Kernel 2.4.1 with ISA-PnP and 3c509 compiled-in:
Linux version 2.4.1 (root@bart) (gcc version 2.95.2 20000220 (Debian
GNU/Linux)) #1 Sam Feb 3 19:41:16 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 000000000fef0000 @ 0000000000100000 (usable)
BIOS-e820: 000000000000d000 @ 000000000fff3000 (ACPI data)
BIOS-e820: 0000000000003000 @ 000000000fff0000 (ACPI NVS)
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux ro root=802 mem=256M apm=on
devfs=nomount
Initializing CPU#0
Detected 333.351 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 665.19 BogoMIPS
Memory: 255788k/262144k available (858k kernel code, 5968k reserved,
350k data, 188k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Mendocino) stepping 00
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfaec0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
got res[10000000:13ffffff] for resource 0 of S3 Inc. 86c968 [Vision
968 VRAM] rev 0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for Pnp cards...
isapnp: Card 'TERRATEC SOUNDSYSTEM BASE 1'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
DMI 2.1 present.
30 structures occupying 806 bytes.
DMI table at 0x000F0800.
BIOS Vendor: Award Software International, Inc.
BIOS Version: 4.51 PG
BIOS Release: 01/25/99
Board Vendor: Gigabyte Technology Co. Ltd..
Board Name: i440BX-W977.
Board Version: .
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 169928kB/56642kB, 512 slots per queue
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 11, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c875E detected
sym53c875E-0: rev 0x26 on pci bus 0 device 11 function 0 irq 11
sym53c875E-0: ID 7, Fast-20, Parity Checking
sym53c875E-0: on-chip RAM at 0xed000000
sym53c875E-0: restart (scsi reset).
sym53c875E-0: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx - version 1.6b
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: IBM Model: DNES-309170W Rev: SAH0
Type: Direct-Access ANSI SCSI revision: 03
sym53c875E-0-<8,0>: tagged command queue depth set to 8
Detected scsi disk sda at scsi0, channel 0, id 8, lun 0
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync msg in: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=16 fak=0
chg=0.
sym53c875E-0-<8,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB)
Partition check:
/dev/scsi/host0/bus0/target8/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 >
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15)
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:07.2
PCI: The same IRQ used for device 00:0b.0
uhci.c: USB UHCI at I/O 0xe000, IRQ 11
uhci.c: detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
devfs: v0.102 (20000622) Richard Gooch ([email protected])
devfs: boot_options: 0x2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 188k freed
Adding Swap: 263144k swap-space (priority -1)
Real Time Clock Driver v1.10d

- Kernel 2.4.1 with ISA-PnP compiled-in and 3c509 compiled as module:
Linux version 2.4.1 (root@bart) (gcc version 2.95.2 20000220 (Debian
GNU/Linux)) #1 Sam Feb 3 20:00:58 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 000000000fef0000 @ 0000000000100000 (usable)
BIOS-e820: 000000000000d000 @ 000000000fff3000 (ACPI data)
BIOS-e820: 0000000000003000 @ 000000000fff0000 (ACPI NVS)
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=802 mem=256M apm=on
devfs=nomount
Initializing CPU#0
Detected 333.352 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 665.19 BogoMIPS
Memory: 255796k/262144k available (853k kernel code, 5960k reserved,
348k data, 188k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Mendocino) stepping 00
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfaec0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
got res[10000000:13ffffff] for resource 0 of S3 Inc. 86c968 [Vision
968 VRAM] rev 0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for Pnp cards...
isapnp: Card 'TERRATEC SOUNDSYSTEM BASE 1'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
DMI 2.1 present.
30 structures occupying 806 bytes.
DMI table at 0x000F0800.
BIOS Vendor: Award Software International, Inc.
BIOS Version: 4.51 PG
BIOS Release: 01/25/99
Board Vendor: Gigabyte Technology Co. Ltd..
Board Name: i440BX-W977.
Board Version: .
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 169933kB/56644kB, 512 slots per queue
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 11, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c875E detected
sym53c875E-0: rev 0x26 on pci bus 0 device 11 function 0 irq 11
sym53c875E-0: ID 7, Fast-20, Parity Checking
sym53c875E-0: on-chip RAM at 0xed000000
sym53c875E-0: restart (scsi reset).
sym53c875E-0: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx - version 1.6b
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: IBM Model: DNES-309170W Rev: SAH0
Type: Direct-Access ANSI SCSI revision: 03
sym53c875E-0-<8,0>: tagged command queue depth set to 8
Detected scsi disk sda at scsi0, channel 0, id 8, lun 0
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync msg in: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=16 fak=0
chg=0.
sym53c875E-0-<8,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB)
Partition check:
/dev/scsi/host0/bus0/target8/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 >
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15)
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:07.2
PCI: The same IRQ used for device 00:0b.0
uhci.c: USB UHCI at I/O 0xe000, IRQ 11
uhci.c: detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
devfs: v0.102 (20000622) Richard Gooch ([email protected])
devfs: boot_options: 0x2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 188k freed
Adding Swap: 263144k swap-space (priority -1)
Real Time Clock Driver v1.10d

(after `modprobe 3c509`)
nothing (error message)

- Kernel 2.4.1 with ISA-PnP and 3c509 compiled as modules:
Linux version 2.4.1 (root@bart) (gcc version 2.95.2 20000220 (Debian
GNU/Linux)) #1 Sam Feb 3 20:19:11 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 000000000fef0000 @ 0000000000100000 (usable)
BIOS-e820: 000000000000d000 @ 000000000fff3000 (ACPI data)
BIOS-e820: 0000000000003000 @ 000000000fff0000 (ACPI NVS)
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=802 mem=256M apm=on
devfs=nomount
Initializing CPU#0
Detected 333.351 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 665.19 BogoMIPS
Memory: 255824k/262144k available (838k kernel code, 5932k reserved,
343k data, 184k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Mendocino) stepping 00
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfaec0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
got res[10000000:13ffffff] for resource 0 of S3 Inc. 86c968 [Vision
968 VRAM] rev 0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
DMI 2.1 present.
30 structures occupying 806 bytes.
DMI table at 0x000F0800.
BIOS Vendor: Award Software International, Inc.
BIOS Version: 4.51 PG
BIOS Release: 01/25/99
Board Vendor: Gigabyte Technology Co. Ltd..
Board Name: i440BX-W977.
Board Version: .
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 169957kB/56652kB, 512 slots per queue
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 11, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c875E detected
sym53c875E-0: rev 0x26 on pci bus 0 device 11 function 0 irq 11
sym53c875E-0: ID 7, Fast-20, Parity Checking
sym53c875E-0: on-chip RAM at 0xed000000
sym53c875E-0: restart (scsi reset).
sym53c875E-0: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx - version 1.6b
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: IBM Model: DNES-309170W Rev: SAH0
Type: Direct-Access ANSI SCSI revision: 03
sym53c875E-0-<8,0>: tagged command queue depth set to 8
Detected scsi disk sda at scsi0, channel 0, id 8, lun 0
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync msg in: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=16 fak=0
chg=0.
sym53c875E-0-<8,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB)
Partition check:
/dev/scsi/host0/bus0/target8/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 >
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15)
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:07.2
PCI: The same IRQ used for device 00:0b.0
uhci.c: USB UHCI at I/O 0xe000, IRQ 11
uhci.c: detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
devfs: v0.102 (20000622) Richard Gooch ([email protected])
devfs: boot_options: 0x2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 184k freed
Adding Swap: 263144k swap-space (priority -1)
Real Time Clock Driver v1.10d

(after `insmod /lib/modules/2.4.1/.../3c509.o`)
nothing (error message)

(after `modprobe 3c509`)
isapnp: Scanning for Pnp cards...
isapnp: Card 'TERRATEC SOUNDSYSTEM BASE 1'
isapnp: 1 Plug & Play card detected total

plus error message

- Kernel 2.4.1 with ISA-PnP left out and 3c509 compiled as module:
Linux version 2.4.1 (root@bart) (gcc version 2.95.2 20000220 (Debian
GNU/Linux)) #1 Sam Feb 3 20:33:57 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 000000000fef0000 @ 0000000000100000 (usable)
BIOS-e820: 000000000000d000 @ 000000000fff3000 (ACPI data)
BIOS-e820: 0000000000003000 @ 000000000fff0000 (ACPI NVS)
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=802 mem=256M apm=on
devfs=nomount
Initializing CPU#0
Detected 333.351 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 665.19 BogoMIPS
Memory: 255824k/262144k available (838k kernel code, 5932k reserved,
343k data, 184k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Mendocino) stepping 00
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfaec0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
got res[10000000:13ffffff] for resource 0 of S3 Inc. 86c968 [Vision
968 VRAM] rev 0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
DMI 2.1 present.
30 structures occupying 806 bytes.
DMI table at 0x000F0800.
BIOS Vendor: Award Software International, Inc.
BIOS Version: 4.51 PG
BIOS Release: 01/25/99
Board Vendor: Gigabyte Technology Co. Ltd..
Board Name: i440BX-W977.
Board Version: .
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 169957kB/56652kB, 512 slots per queue
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 11, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c875E detected
sym53c875E-0: rev 0x26 on pci bus 0 device 11 function 0 irq 11
sym53c875E-0: ID 7, Fast-20, Parity Checking
sym53c875E-0: on-chip RAM at 0xed000000
sym53c875E-0: restart (scsi reset).
sym53c875E-0: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx - version 1.6b
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: IBM Model: DNES-309170W Rev: SAH0
Type: Direct-Access ANSI SCSI revision: 03
sym53c875E-0-<8,0>: tagged command queue depth set to 8
Detected scsi disk sda at scsi0, channel 0, id 8, lun 0
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync msg in: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=16 fak=0
chg=0.
sym53c875E-0-<8,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB)
Partition check:
/dev/scsi/host0/bus0/target8/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 >
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15)
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:07.2
PCI: The same IRQ used for device 00:0b.0
uhci.c: USB UHCI at I/O 0xe000, IRQ 11
uhci.c: detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
devfs: v0.102 (20000622) Richard Gooch ([email protected])
devfs: boot_options: 0x2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 184k freed
Adding Swap: 263144k swap-space (priority -1)
Real Time Clock Driver v1.10d

(after modprobe 3c509)
nothing

- Kernel 2.4.1 with ISA-PnP left out and 3c509 compiled-in:
Linux version 2.4.1 (root@bart) (gcc version 2.95.2 20000220 (Debian
GNU/Linux)) #1 Sam Feb 3 21:13:46 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 000000000fef0000 @ 0000000000100000 (usable)
BIOS-e820: 000000000000d000 @ 000000000fff3000 (ACPI data)
BIOS-e820: 0000000000003000 @ 000000000fff0000 (ACPI NVS)
On node 0 totalpages: 65536
zone(0): 4096 pages.
zone(1): 61440 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux ro root=802 mem=256M apm=on
devfs=nomount
Initializing CPU#0
Detected 333.351 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 665.19 BogoMIPS
Memory: 255816k/262144k available (841k kernel code, 5940k reserved,
344k data, 184k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000
CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU: Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Mendocino) stepping 00
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfaec0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
got res[10000000:13ffffff] for resource 0 of S3 Inc. 86c968 [Vision
968 VRAM] rev 0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
DMI 2.1 present.
30 structures occupying 806 bytes.
DMI table at 0x000F0800.
BIOS Vendor: Award Software International, Inc.
BIOS Version: 4.51 PG
BIOS Release: 01/25/99
Board Vendor: Gigabyte Technology Co. Ltd..
Board Name: i440BX-W977.
Board Version: .
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
pty: 256 Unix98 ptys configured
block: queued sectors max/low 169952kB/56650kB, 512 slots per queue
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
eth0: 3c509 at 0x210, BNC port, address 00 60 8c c1 da da, IRQ 3.
3c509.c:1.16 (2.2) 2/3/98 [email protected].
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
SCSI subsystem driver Revision: 1.00
sym53c8xx: at PCI bus 0, device 11, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c875E detected
sym53c875E-0: rev 0x26 on pci bus 0 device 11 function 0 irq 11
sym53c875E-0: ID 7, Fast-20, Parity Checking
sym53c875E-0: on-chip RAM at 0xed000000
sym53c875E-0: restart (scsi reset).
sym53c875E-0: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx - version 1.6b
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: IBM Model: DNES-309170W Rev: SAH0
Type: Direct-Access ANSI SCSI revision: 03
sym53c875E-0-<8,0>: tagged command queue depth set to 8
Detected scsi disk sda at scsi0, channel 0, id 8, lun 0
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: wide msgout: 1-2-3-1.
sym53c875E-0-<8,0>: wide msgin: 1-2-3-1.
sym53c875E-0-<8,0>: wide: wide=1 chg=0.
sym53c875E-0-<8,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync msg in: 1-3-1-c-10.
sym53c875E-0-<8,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=16 fak=0
chg=0.
sym53c875E-0-<8,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB)
Partition check:
/dev/scsi/host0/bus0/target8/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 >
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 15)
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sym53c875E-0-<1,0>: sync msgout: 1-3-1-c-10.
sym53c875E-0-<1,0>: sync msg in: 1-3-1-c-f.
sym53c875E-0-<1,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0
chg=0.
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:07.2
PCI: The same IRQ used for device 00:0b.0
uhci.c: USB UHCI at I/O 0xe000, IRQ 11
uhci.c: detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
devfs: v0.102 (20000622) Richard Gooch ([email protected])
devfs: boot_options: 0x2
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 184k freed
Adding Swap: 263144k swap-space (priority -1)
eth0: Setting Rx mode to 1 addresses.
Real Time Clock Driver v1.10d

HTH,
Viktor
--
Viktor Rosenfeld
WWW: http://www.informatik.hu-berlin.de/~rosenfel/
Geek Code (3.1):
GCS/SS d-@ s+: a20 C++@ UL++$ P+ L+++ E--- W++ N++ o? K? !W O? M? V?
PS++@ PE+(-) Y+ P?(+++) t+ 5+ X- R? !tv b+ DI+ D- G e>+++ h-- r- !y+

2001-02-03 21:18:43

by Russell King

[permalink] [raw]

Subject: Re: [BUG?] ISA-PnP and 3c509 NIC won't work together

Viktor Rosenfeld writes:
> With ISA-PnP compiled in, and 3c509 support compiled as module:
> # modprobe 3c509
> /lib/modules/2.4.1/kernel/drivers/net/3c509.o: invalid parameter parm_io
> /lib/modules/2.4.1/kernel/drivers/net/3c509.o: insmod
> /lib/modules/2.4.1/kernel/drivers/net/3c509.o failed
> /lib/modules/2.4.1/kernel/drivers/net/3c509.o: insmod 3c509 failed

Silly question, but shouldn't you fix this "invalid parameter parm_io"
error first?

iirc, insmod won't insert modules when you have parameters for missing
symbols.

--
Russell King ([email protected]) The developer of ARM Linux
http://www.arm.linux.org.uk/personal/aboutme.html

2001-02-03 21:19:53

by Brian Gerst

[permalink] [raw]

Subject: Re: [BUG?] ISA-PnP and 3c509 NIC won't work together

Viktor Rosenfeld wrote:
>
> Hi kernel hackers,
>
> I have troubles getting both ISA-PnP and the driver for my 3c509 NIC
> working together.
>
> I can only get my NIC to work when I leave ISA-PnP completely out of the
> kernel. When I have ISA-PnP activated, the card will not show up in
> /proc/isapnp (see below) nor is it listed in the table that my system
> displays prior to starting LILO. The kernel help on the 3c509 driver
> suggests to completely deactivate PNP for the NIC, which is what I have
> done since kernel 2.0.x. Unfortunately, I can't find info on
> re-enabling PNP on the card.
>
> Below, I have attached the content of /proc/isapnp. If I can do
> anything to provide more info, let me know.

Go to 3Com's site and get the setup program for the card (for DOS). It
is configurable via eeprom for io and irq or PnP mode.

--
Brian Gerst

2001-02-03 23:01:28

by Keith Owens

[permalink] [raw]

Subject: Re: [BUG?] ISA-PnP and 3c509 NIC won't work together

On Sat, 03 Feb 2001 18:54:44 +0100,
Viktor Rosenfeld <[email protected]> wrote:
>With ISA-PnP compiled in, and 3c509 support compiled as module:
># modprobe 3c509
>/lib/modules/2.4.1/kernel/drivers/net/3c509.o: invalid parameter parm_io
>/lib/modules/2.4.1/kernel/drivers/net/3c509.o: insmod
>/lib/modules/2.4.1/kernel/drivers/net/3c509.o failed
>/lib/modules/2.4.1/kernel/drivers/net/3c509.o: insmod 3c509 failed

You passed an unknown parameter io_parm to 3c509 and insmod rejected
it. This has nothing to do with isa-pnp nor the 3c509, it is a pure
user error. Correct modules.conf before doing anything else.