Hello,
This patch adds support for the Omnivision OV5647 sensor.
At the moment it only supports 640x480 in Raw 8.
This is the fourth version of the OV5647 camera driver patchset.
v4:
- Add correct license
- Revert debugging info to generic infrastructure
- Turn defines into enums
- Correct code style issues
- Remove unused defines
- Make sure all errors where being handled
- Rename some functions to make code more readable
- Add some debugging info
v3:
- No changes. Re-submitted due to lack of responses
v2:
- Corrections in DT documentation
Ramiro Oliveira (2):
Add OV5647 device tree documentation
Add support for OV5647 sensor
.../devicetree/bindings/media/i2c/ov5647.txt | 19 +
MAINTAINERS | 7 +
drivers/media/i2c/Kconfig | 12 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov5647.c | 861 +++++++++++++++++++++
5 files changed, 900 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5647.txt
create mode 100644 drivers/media/i2c/ov5647.c
--
2.10.2
Add device tree documentation.
Signed-off-by: Ramiro Oliveira <[email protected]>
---
.../devicetree/bindings/media/i2c/ov5647.txt | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5647.txt
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5647.txt b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
new file mode 100644
index 0000000..4c91b3b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
@@ -0,0 +1,19 @@
+Omnivision OV5647 raw image sensor
+---------------------------------
+
+OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
+and CCI (I2C compatible) control bus.
+
+Required properties:
+
+- compatible : "ovti,ov5647";
+- reg : I2C slave address of the sensor;
+
+The common video interfaces bindings (see video-interfaces.txt) should be
+used to specify link to the image data receiver. The OV5647 device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Following properties are valid for the endpoint node:
+
+- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
+ video-interfaces.txt. The sensor supports only two data lanes.
--
2.10.2
Add support for OV5647 sensor.
Modes supported:
- 640x480 RAW 8
Signed-off-by: Ramiro Oliveira <[email protected]>
---
MAINTAINERS | 7 +
drivers/media/i2c/Kconfig | 12 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/ov5647.c | 861 +++++++++++++++++++++++++++++++++++++++++++++
4 files changed, 881 insertions(+)
create mode 100644 drivers/media/i2c/ov5647.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 93e9f42..6a71422 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8895,6 +8895,13 @@ M: Harald Welte <[email protected]>
S: Maintained
F: drivers/char/pcmcia/cm4040_cs.*
+OMNIVISION OV5647 SENSOR DRIVER
+M: Ramiro Oliveira <[email protected]>
+L: [email protected]
+T: git git://linuxtv.org/media_tree.git
+S: Maintained
+F: drivers/media/i2c/ov5647.c
+
OMNIVISION OV7670 SENSOR DRIVER
M: Jonathan Corbet <[email protected]>
L: [email protected]
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 2669b4b..4237165 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -531,6 +531,18 @@ config VIDEO_OV2659
To compile this driver as a module, choose M here: the
module will be called ov2659.
+config VIDEO_OV5647
+ tristate "OmniVision OV5647 sensor support"
+ depends on OF
+ depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+ depends on MEDIA_CAMERA_SUPPORT
+ ---help---
+ This is a Video4Linux2 sensor-level driver for the OmniVision
+ OV5647 camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ov5647.
+
config VIDEO_OV7640
tristate "OmniVision OV7640 sensor support"
depends on I2C && VIDEO_V4L2
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 92773b2..0d9014c 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -82,3 +82,4 @@ obj-$(CONFIG_VIDEO_IR_I2C) += ir-kbd-i2c.o
obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o
obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
+obj-$(CONFIG_VIDEO_OV5647) += ov5647.o
diff --git a/drivers/media/i2c/ov5647.c b/drivers/media/i2c/ov5647.c
new file mode 100644
index 0000000..0b3b4f2
--- /dev/null
+++ b/drivers/media/i2c/ov5647.c
@@ -0,0 +1,861 @@
+/*
+ * A V4L2 driver for OmniVision OV5647 cameras.
+ *
+ * Based on Samsung S5K6AAFX SXGA 1/6" 1.3M CMOS Image Sensor driver
+ * Copyright (C) 2011 Sylwester Nawrocki <[email protected]>
+ *
+ * Based on Omnivision OV7670 Camera Driver
+ * Copyright (C) 2006-7 Jonathan Corbet <[email protected]>
+ *
+ * Copyright (C) 2016, Synopsys, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed .as is. WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/delay.h>
+#include <linux/videodev2.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-mediabus.h>
+#include <media/v4l2-image-sizes.h>
+#include <media/v4l2-of.h>
+#include <linux/io.h>
+
+#define SENSOR_NAME "ov5647"
+
+#define OV5647_SW_RESET 0x1003
+#define OV5647_REG_CHIPID_H 0x300A
+#define OV5647_REG_CHIPID_L 0x300B
+
+#define REG_TERM 0xfffe
+#define VAL_TERM 0xfe
+#define REG_DLY 0xffff
+
+#define OV5647_ROW_START 0x01
+#define OV5647_ROW_START_MIN 0
+#define OV5647_ROW_START_MAX 2004
+#define OV5647_ROW_START_DEF 54
+
+#define OV5647_COLUMN_START 0x02
+#define OV5647_COLUMN_START_MIN 0
+#define OV5647_COLUMN_START_MAX 2750
+#define OV5647_COLUMN_START_DEF 16
+
+#define OV5647_WINDOW_HEIGHT 0x03
+#define OV5647_WINDOW_HEIGHT_MIN 2
+#define OV5647_WINDOW_HEIGHT_MAX 2006
+#define OV5647_WINDOW_HEIGHT_DEF 1944
+
+#define OV5647_WINDOW_WIDTH 0x04
+#define OV5647_WINDOW_WIDTH_MIN 2
+#define OV5647_WINDOW_WIDTH_MAX 2752
+#define OV5647_WINDOW_WIDTH_DEF 2592
+
+struct regval_list {
+ u16 addr;
+ u8 data;
+};
+
+struct cfg_array {
+ struct regval_list *regs;
+ int size;
+};
+
+struct sensor_win_size {
+ int width;
+ int height;
+ unsigned int hoffset;
+ unsigned int voffset;
+ unsigned int hts;
+ unsigned int vts;
+ unsigned int pclk;
+ unsigned int mipi_bps;
+ unsigned int fps_fixed;
+ unsigned int bin_factor;
+ unsigned int intg_min;
+ unsigned int intg_max;
+ void *regs;
+ int regs_size;
+ int (*set_size)(struct v4l2_subdev *sd);
+};
+
+
+struct ov5647 {
+ struct device *dev;
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+ struct mutex lock;
+ struct v4l2_mbus_framefmt format;
+ struct sensor_format_struct *fmt;
+ unsigned int width;
+ unsigned int height;
+ unsigned int capture_mode;
+ int hue;
+ struct v4l2_fract tpf;
+ struct sensor_win_size *current_wins;
+};
+
+static inline struct ov5647 *to_state(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct ov5647, sd);
+}
+
+static struct regval_list sensor_oe_disable_regs[] = {
+ {0x3000, 0x00},
+ {0x3001, 0x00},
+ {0x3002, 0x00},
+};
+
+static struct regval_list sensor_oe_enable_regs[] = {
+ {0x3000, 0x0f},
+ {0x3001, 0xff},
+ {0x3002, 0xe4},
+};
+
+static struct regval_list ov5647_640x480[] = {
+ {0x0100, 0x00},
+ {0x0103, 0x01},
+ {0x3034, 0x08},
+ {0x3035, 0x21},
+ {0x3036, 0x46},
+ {0x303c, 0x11},
+ {0x3106, 0xf5},
+ {0x3821, 0x07},
+ {0x3820, 0x41},
+ {0x3827, 0xec},
+ {0x370c, 0x0f},
+ {0x3612, 0x59},
+ {0x3618, 0x00},
+ {0x5000, 0x06},
+ {0x5001, 0x01},
+ {0x5002, 0x41},
+ {0x5003, 0x08},
+ {0x5a00, 0x08},
+ {0x3000, 0x00},
+ {0x3001, 0x00},
+ {0x3002, 0x00},
+ {0x3016, 0x08},
+ {0x3017, 0xe0},
+ {0x3018, 0x44},
+ {0x301c, 0xf8},
+ {0x301d, 0xf0},
+ {0x3a18, 0x00},
+ {0x3a19, 0xf8},
+ {0x3c01, 0x80},
+ {0x3b07, 0x0c},
+ {0x380c, 0x07},
+ {0x380d, 0x68},
+ {0x380e, 0x03},
+ {0x380f, 0xd8},
+ {0x3814, 0x31},
+ {0x3815, 0x31},
+ {0x3708, 0x64},
+ {0x3709, 0x52},
+ {0x3808, 0x02},
+ {0x3809, 0x80},
+ {0x380a, 0x01},
+ {0x380b, 0xE0},
+ {0x3801, 0x00},
+ {0x3802, 0x00},
+ {0x3803, 0x00},
+ {0x3804, 0x0a},
+ {0x3805, 0x3f},
+ {0x3806, 0x07},
+ {0x3807, 0xa1},
+ {0x3811, 0x08},
+ {0x3813, 0x02},
+ {0x3630, 0x2e},
+ {0x3632, 0xe2},
+ {0x3633, 0x23},
+ {0x3634, 0x44},
+ {0x3636, 0x06},
+ {0x3620, 0x64},
+ {0x3621, 0xe0},
+ {0x3600, 0x37},
+ {0x3704, 0xa0},
+ {0x3703, 0x5a},
+ {0x3715, 0x78},
+ {0x3717, 0x01},
+ {0x3731, 0x02},
+ {0x370b, 0x60},
+ {0x3705, 0x1a},
+ {0x3f05, 0x02},
+ {0x3f06, 0x10},
+ {0x3f01, 0x0a},
+ {0x3a08, 0x01},
+ {0x3a09, 0x27},
+ {0x3a0a, 0x00},
+ {0x3a0b, 0xf6},
+ {0x3a0d, 0x04},
+ {0x3a0e, 0x03},
+ {0x3a0f, 0x58},
+ {0x3a10, 0x50},
+ {0x3a1b, 0x58},
+ {0x3a1e, 0x50},
+ {0x3a11, 0x60},
+ {0x3a1f, 0x28},
+ {0x4001, 0x02},
+ {0x4004, 0x02},
+ {0x4000, 0x09},
+ {0x4837, 0x24},
+ {0x4050, 0x6e},
+ {0x4051, 0x8f},
+ {0x0100, 0x01},
+};
+
+struct sensor_format_struct;
+
+/**
+ * @short I2C Write operation
+ * @param[in] i2c_client I2C client
+ * @param[in] reg register address
+ * @param[in] val value to write
+ * @return Error code
+ */
+static int ov5647_write(struct v4l2_subdev *sd, u16 reg, u8 val)
+{
+ int ret;
+ unsigned char data[3] = { reg >> 8, reg & 0xff, val};
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ ret = i2c_master_send(client, data, 3);
+ if (ret != 3) {
+ dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n",
+ __func__, reg);
+ return ret < 0 ? ret : -EIO;
+ }
+ return 0;
+}
+
+/**
+ * @short I2C Read operation
+ * @param[in] i2c_client I2C client
+ * @param[in] reg register address
+ * @param[out] val value read
+ * @return Error code
+ */
+static int ov5647_read(struct v4l2_subdev *sd, u16 reg, u8 *val)
+{
+ int ret;
+ unsigned char data_w[2] = { reg >> 8, reg & 0xff };
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+
+ ret = i2c_master_send(client, data_w, 2);
+
+ if (ret < 2) {
+ dev_dbg(&client->dev, "%s: i2c read error, reg: %x\n",
+ __func__, reg);
+ return ret < 0 ? ret : -EIO;
+ }
+
+
+ ret = i2c_master_recv(client, val, 1);
+
+ if (ret < 1) {
+ dev_dbg(&client->dev, "%s: i2c read error, reg: %x\n",
+ __func__, reg);
+ return ret < 0 ? ret : -EIO;
+ }
+ return 0;
+}
+
+static int ov5647_write_array(struct v4l2_subdev *sd,
+ struct regval_list *regs, int array_size)
+{
+ int i = 0;
+ int ret = 0;
+
+ if (!regs)
+ return -EINVAL;
+
+ while (i < array_size) {
+ ret = ov5647_write(sd, regs->addr, regs->data);
+ if (ret < 0)
+ return ret;
+ i++;
+ regs++;
+ }
+ return 0;
+}
+
+static void ov5647_set_virtual_channel(struct v4l2_subdev *sd, int channel)
+{
+ u8 channel_id;
+
+ ov5647_read(sd, 0x4814, &channel_id);
+ channel_id &= ~(3 << 6);
+ ov5647_write(sd, 0x4814, channel_id | (channel << 6));
+}
+
+void ov5647_stream_on(struct v4l2_subdev *sd)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ ov5647_write(sd, 0x4202, 0x00);
+ dev_dbg(&client->dev, "Stream on");
+ ov5647_write(sd, 0x300D, 0x00);
+}
+
+void ov5647_stream_off(struct v4l2_subdev *sd)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ ov5647_write(sd, 0x4202, 0x0f);
+ dev_dbg(&client->dev, "Stream off");
+ ov5647_write(sd, 0x300D, 0x01);
+}
+
+/****************************************************************************/
+
+/**
+ * @short Set SW standby
+ * @param[in] sd v4l2 sd
+ * @param[in] stanby standby mode status (on or off)
+ * @return Error code
+ */
+static int set_sw_standby(struct v4l2_subdev *sd, bool standby)
+{
+ int ret;
+ unsigned char rdval;
+
+ ret = ov5647_read(sd, 0x0100, &rdval);
+ if (ret != 0)
+ return ret;
+
+ if (standby)
+ ret = ov5647_write(sd, 0x0100, rdval&0xfe);
+ else
+ ret = ov5647_write(sd, 0x0100, rdval|0x01);
+
+ return ret;
+}
+
+/**
+ * @short Store information about the video data format.
+ */
+static struct sensor_format_struct {
+ __u8 *desc;
+ u32 mbus_code;
+ struct regval_list *regs;
+ int regs_size;
+ int bpp;
+} sensor_formats[] = {
+ {
+ .desc = "Raw RGB Bayer",
+ .mbus_code = MEDIA_BUS_FMT_SBGGR8_1X8,
+ .regs = ov5647_640x480,
+ .regs_size = ARRAY_SIZE(ov5647_640x480),
+ .bpp = 1
+ },
+};
+#define N_FMTS ARRAY_SIZE(sensor_formats)
+
+/* ----------------------------------------------------------------------- */
+
+/**
+ * @short Initialize sensor
+ * @param[in] sd v4l2 subdev
+ * @param[in] val not used
+ * @return Error code
+ */
+static int __sensor_init(struct v4l2_subdev *sd)
+{
+ int ret;
+ u8 resetval;
+ u8 rdval;
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ dev_dbg(&client->dev, "sensor init\n");
+
+ ret = ov5647_read(sd, 0x0100, &rdval);
+ if (ret != 0)
+ return ret;
+
+ ov5647_write(sd, 0x4800, 0x25);
+ ov5647_stream_off(sd);
+
+ ret = ov5647_write_array(sd, ov5647_640x480,
+ ARRAY_SIZE(ov5647_640x480));
+ if (ret < 0) {
+ dev_err(&client->dev, "write sensor_default_regs error\n");
+ return ret;
+ }
+
+ ov5647_set_virtual_channel(sd, 0);
+
+ ov5647_read(sd, 0x0100, &resetval);
+ if (!resetval&0x01) {
+ dev_err(&client->dev, "Device was in SW standby");
+ ov5647_write(sd, 0x0100, 0x01);
+ }
+
+ ov5647_write(sd, 0x4800, 0x04);
+ ov5647_stream_on(sd);
+
+ return 0;
+}
+
+/**
+ * @short Control sensor power state
+ * @param[in] sd v4l2 subdev
+ * @param[in] on Sensor power
+ * @return Error code
+ */
+static int sensor_power(struct v4l2_subdev *sd, int on)
+{
+ int ret;
+ struct ov5647 *ov5647 = to_state(sd);
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ ret = 0;
+ mutex_lock(&ov5647->lock);
+
+ if (on) {
+ dev_dbg(&client->dev, "OV5647 power on!\n");
+
+ ret = ov5647_write_array(sd, sensor_oe_enable_regs,
+ ARRAY_SIZE(sensor_oe_enable_regs));
+
+ ret = __sensor_init(sd);
+
+ if (ret < 0)
+ dev_err(&client->dev,
+ "Camera not available! Check Power!\n");
+ } else {
+ dev_dbg(&client->dev, "OV5647 power off!\n");
+
+ dev_dbg(&client->dev, "disable oe\n");
+ ret = ov5647_write_array(sd, sensor_oe_disable_regs,
+ ARRAY_SIZE(sensor_oe_disable_regs));
+
+ if (ret < 0)
+ dev_dbg(&client->dev, "disable oe failed!\n");
+
+ ret = set_sw_standby(sd, true);
+
+ if (ret < 0)
+ dev_dbg(&client->dev, "soft stby failed!\n");
+
+ }
+
+ mutex_unlock(&ov5647->lock);
+
+ return ret;
+}
+
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+/**
+ * @short Get register value
+ * @param[in] sd v4l2 subdev
+ * @param[in] reg register struct
+ * @return Error code
+ */
+static int sensor_get_register(struct v4l2_subdev *sd,
+ struct v4l2_dbg_register *reg)
+{
+ unsigned char val = 0;
+ int ret;
+
+ ret = ov5647_read(sd, reg->reg & 0xff, &val);
+ reg->val = val;
+ reg->size = 1;
+ return ret;
+}
+
+/**
+ * @short Set register value
+ * @param[in] sd v4l2 subdev
+ * @param[in] reg register struct
+ * @return Error code
+ */
+static int sensor_set_register(struct v4l2_subdev *sd,
+ const struct v4l2_dbg_register *reg)
+{
+ ov5647_write(sd, reg->reg & 0xff, reg->val & 0xff);
+ return 0;
+}
+#endif
+
+/* ----------------------------------------------------------------------- */
+
+/**
+ * @short Subdev core operations registration
+ */
+static const struct v4l2_subdev_core_ops sensor_core_ops = {
+ .s_power = sensor_power,
+#ifdef CONFIG_VIDEO_ADV_DEBUG
+ .g_register = sensor_get_register,
+ .s_register = sensor_set_register,
+#endif
+};
+
+/* ----------------------------------------------------------------------- */
+
+
+
+/**
+ * @short Enumerate available image formats
+ * @param[in] sd v4l2 subdev
+ * @param[in] index index
+ * @param[in] code MBUS Pixel code
+ * @return Error code
+ */
+static int sensor_enum_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->pad || code->index >= N_FMTS)
+ return -EINVAL;
+
+ code->code = sensor_formats[code->index].mbus_code;
+ return 0;
+}
+
+/**
+ * @short Try frame format internal function
+ * @param[in] sd v4l2 subdev
+ * @param[in] fmt frame format
+ * @return Error code
+ */
+static int sensor_try_fmt_internal(struct v4l2_subdev *sd,
+ struct v4l2_mbus_framefmt *fmt, struct sensor_format_struct **ret_fmt,
+ struct sensor_win_size **ret_wsize)
+{
+ int index;
+
+ for (index = 0; index < N_FMTS; index++)
+ if (sensor_formats[index].mbus_code == fmt->code)
+ break;
+
+ if (index >= N_FMTS)
+ return -EINVAL;
+
+ if (ret_fmt != NULL)
+ *ret_fmt = sensor_formats + index;
+
+ fmt->field = V4L2_FIELD_NONE;
+
+ return 0;
+}
+
+/**
+ * @short Set frame format
+ * @param[in] sd v4l2 subdev
+ * @param[in] fmt frame format
+ * @return Error code
+ */
+static int sensor_s_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *fmt)
+{
+ int ret;
+ struct sensor_format_struct *sensor_fmt;
+ struct sensor_win_size *wsize;
+ struct ov5647 *info = to_state(sd);
+
+ ov5647_write_array(sd, sensor_oe_disable_regs,
+ ARRAY_SIZE(sensor_oe_disable_regs));
+
+ ret = sensor_try_fmt_internal(sd, &fmt->format,
+ &sensor_fmt, &wsize);
+ if (ret)
+ return ret;
+
+ ov5647_write_array(sd, sensor_fmt->regs, sensor_fmt->regs_size);
+
+ ret = 0;
+
+ if (wsize->regs)
+ ov5647_write_array(sd, wsize->regs, wsize->regs_size);
+
+ if (wsize->set_size)
+ wsize->set_size(sd);
+
+ info->fmt = sensor_fmt;
+ info->width = wsize->width;
+ info->height = wsize->height;
+
+ ov5647_write_array(sd, sensor_oe_enable_regs,
+ ARRAY_SIZE(sensor_oe_enable_regs));
+
+ return 0;
+}
+
+/**
+ * @short Set stream parameters
+ * @param[in] sd v4l2 subdev
+ * @param[in] parms stream parameters
+ * @return Error code
+ */
+static int sensor_s_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms)
+{
+ struct v4l2_captureparm *cp = &parms->parm.capture;
+ struct ov5647 *info = to_state(sd);
+
+ if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+ return -EINVAL;
+
+ if (info->tpf.numerator == 0)
+ return -EINVAL;
+
+ info->capture_mode = cp->capturemode;
+
+ return 0;
+}
+
+/**
+ * @short Get stream parameters
+ * @param[in] sd v4l2 subdev
+ * @param[in] parms stream parameters
+ * @return Error code
+ */
+static int sensor_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms)
+{
+ struct v4l2_captureparm *cp = &parms->parm.capture;
+ struct ov5647 *info = to_state(sd);
+
+ if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+ return -EINVAL;
+
+ memset(cp, 0, sizeof(struct v4l2_captureparm));
+ cp->capability = V4L2_CAP_TIMEPERFRAME;
+ cp->capturemode = info->capture_mode;
+
+ return 0;
+}
+
+/**
+ * @short Subdev video operations registration
+ *
+ */
+static const struct v4l2_subdev_video_ops sensor_video_ops = {
+ .s_parm = sensor_s_parm,
+ .g_parm = sensor_g_parm,
+};
+
+/* ----------------------------------------------------------------------- */
+
+/**
+ * @short Subdev operations registration
+ *
+ */
+static const struct v4l2_subdev_ops subdev_ops = {
+ .core = &sensor_core_ops,
+ .video = &sensor_video_ops,
+};
+
+/* -----------------------------------------------------------------------------
+ * V4L2 subdev internal operations
+ */
+
+/**
+ * @short Detect camera version and model
+ * @param[in] sd v4l2 subdev
+ * @return Error code
+ */
+int ov5647_detect(struct v4l2_subdev *sd)
+{
+ unsigned char v;
+ int ret;
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ ret = ov5647_write(sd, OV5647_SW_RESET, 0x01);
+ if (ret < 0)
+ return ret;
+ ret = ov5647_read(sd, OV5647_REG_CHIPID_H, &v);
+ if (ret < 0)
+ return ret;
+ if (v != 0x56) {
+ dev_err(&client->dev, "Wrong model version detected");
+ return -ENODEV;
+ }
+ ret = ov5647_read(sd, OV5647_REG_CHIPID_L, &v);
+ if (ret < 0)
+ return ret;
+ if (v != 0x47) {
+ dev_err(&client->dev, "Wrong model version detected");
+ return -ENODEV;
+ }
+
+ ret = ov5647_write(sd, OV5647_SW_RESET, 0x00);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+/**
+ * @short Detect if camera is registered
+ * @param[in] sd v4l2 subdev
+ * @return Error code
+ */
+static int ov5647_registered(struct v4l2_subdev *sd)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+
+ dev_info(&client->dev, "OV5647 detected at address 0x%02x\n",
+ client->addr);
+
+ return 0;
+}
+
+/**
+ * @short Open device
+ * @param[in] sd v4l2 subdev
+ * @param[in] fh v4l2 file handler
+ * @return Error code
+ */
+static int ov5647_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+ struct v4l2_mbus_framefmt *format =
+ v4l2_subdev_get_try_format(sd, fh->pad, 0);
+ struct v4l2_rect *crop =
+ v4l2_subdev_get_try_crop(sd, fh->pad, 0);
+
+ crop->left = OV5647_COLUMN_START_DEF;
+ crop->top = OV5647_ROW_START_DEF;
+ crop->width = OV5647_WINDOW_WIDTH_DEF;
+ crop->height = OV5647_WINDOW_HEIGHT_DEF;
+
+ format->code = MEDIA_BUS_FMT_SBGGR8_1X8;
+
+ format->width = OV5647_WINDOW_WIDTH_DEF;
+ format->height = OV5647_WINDOW_HEIGHT_DEF;
+ format->field = V4L2_FIELD_NONE;
+ format->colorspace = V4L2_COLORSPACE_SRGB;
+
+ return sensor_power(sd, true);
+}
+
+/**
+ * @short Open device
+ * @param[in] sd v4l2 subdev
+ * @param[in] fh v4l2 file handler
+ * @return Error code
+ */
+static int ov5647_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+ return sensor_power(sd, false);
+}
+
+/**
+ * @short Subdev internal operations registration
+ *
+ */
+static const struct v4l2_subdev_internal_ops ov5647_subdev_internal_ops = {
+ .registered = ov5647_registered,
+ .open = ov5647_open,
+ .close = ov5647_close,
+};
+
+/**
+ * @short Initialization routine - Entry point of the driver
+ * @param[in] client pointer to the i2c client structure
+ * @param[in] id pointer to the i2c device id structure
+ * @return 0 on success and a negative number on failure
+ */
+static int ov5647_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct ov5647 *sensor;
+ int ret = 0;
+ struct v4l2_subdev *sd;
+
+ dev_info(&client->dev, "Installing OmniVision OV5647 camera driver\n");
+
+ sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
+ if (sensor == NULL)
+ return -ENOMEM;
+
+ mutex_init(&sensor->lock);
+ sensor->dev = dev;
+
+ sd = &sensor->sd;
+ v4l2_i2c_subdev_init(sd, client, &subdev_ops);
+ sensor->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+ sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
+ sd->entity.function = MEDIA_ENT_F_CAM_SENSOR;
+ ret = media_entity_pads_init(&sd->entity, 1, &sensor->pad);
+ if (ret < 0)
+ goto mutex_remove;
+
+ ret = ov5647_detect(sd);
+ if (ret < 0)
+ goto error;
+
+ ret = v4l2_async_register_subdev(sd);
+ if (ret < 0)
+ goto error;
+
+ return 0;
+error:
+ media_entity_cleanup(&sd->entity);
+mutex_remove:
+ mutex_destroy(&sensor->lock);
+ return ret;
+}
+
+/**
+ * @short Exit routine - Exit point of the driver
+ * @param[in] client pointer to the i2c client structure
+ * @return 0 on success and a negative number on failure
+ */
+static int ov5647_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct ov5647 *ov5647 = to_state(sd);
+
+ v4l2_async_unregister_subdev(&ov5647->sd);
+ media_entity_cleanup(&ov5647->sd.entity);
+ v4l2_device_unregister_subdev(sd);
+ mutex_destroy(&ov5647->lock);
+
+ return 0;
+}
+
+static const struct i2c_device_id ov5647_id[] = {
+ { "ov5647", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, ov5647_id);
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id ov5647_of_match[] = {
+ { .compatible = "ovti,ov5647" },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ov5647_of_match);
+#endif
+
+/**
+ * @short i2c driver structure
+ */
+static struct i2c_driver ov5647_driver = {
+ .driver = {
+ .of_match_table = of_match_ptr(ov5647_of_match),
+ .owner = THIS_MODULE,
+ .name = "ov5647",
+ },
+ .probe = ov5647_probe,
+ .remove = ov5647_remove,
+ .id_table = ov5647_id,
+};
+
+module_i2c_driver(ov5647_driver);
+
+MODULE_AUTHOR("Ramiro Oliveira <[email protected]>");
+MODULE_DESCRIPTION("A low-level driver for OmniVision ov5647 sensors");
+MODULE_LICENSE("GPL v2");
--
2.10.2
Hi!
> Add support for OV5647 sensor.
>
> +static int ov5647_write(struct v4l2_subdev *sd, u16 reg, u8 val)
> +{
> + int ret;
> + unsigned char data[3] = { reg >> 8, reg & 0xff, val};
> + struct i2c_client *client = v4l2_get_subdevdata(sd);
> +
> + ret = i2c_master_send(client, data, 3);
> + if (ret != 3) {
> + dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n",
> + __func__, reg);
> + return ret < 0 ? ret : -EIO;
> + }
> + return 0;
> +}
Sorry, this is wrong. It should something <0 any time error is detected.
> +static int ov5647_write_array(struct v4l2_subdev *sd,
> + struct regval_list *regs, int array_size)
> +{
> + int i = 0;
> + int ret = 0;
> +
> + if (!regs)
> + return -EINVAL;
> +
> + while (i < array_size) {
> + ret = ov5647_write(sd, regs->addr, regs->data);
> + if (ret < 0)
> + return ret;
> + i++;
> + regs++;
> + }
> + return 0;
> +}
For example this expects <0 on error.
> +static int set_sw_standby(struct v4l2_subdev *sd, bool standby)
> +{
> + int ret;
> + unsigned char rdval;
> +
> + ret = ov5647_read(sd, 0x0100, &rdval);
> + if (ret != 0)
> + return ret;
> +
> + if (standby)
> + ret = ov5647_write(sd, 0x0100, rdval&0xfe);
> + else
> + ret = ov5647_write(sd, 0x0100, rdval|0x01);
> +
> + return ret;
if (standby)
rdval &= 0xfe;
else
rdval |= 0x01;
ret = ov5647_write(sd, 0x0100, rdval);
?
> +/**
> + * @short Store information about the video data format.
> + */
> +static struct sensor_format_struct {
> + __u8 *desc;
> + u32 mbus_code;
u8 is suitable here.
> + ov5647_read(sd, 0x0100, &resetval);
> + if (!resetval&0x01) {
add ()s here.
> +static int sensor_power(struct v4l2_subdev *sd, int on)
> +{
> + int ret;
> + struct ov5647 *ov5647 = to_state(sd);
> + struct i2c_client *client = v4l2_get_subdevdata(sd);
> +
> + ret = 0;
> + mutex_lock(&ov5647->lock);
> +
> + if (on) {
> + dev_dbg(&client->dev, "OV5647 power on!\n");
> +
> + ret = ov5647_write_array(sd, sensor_oe_enable_regs,
> + ARRAY_SIZE(sensor_oe_enable_regs));
> +
> + ret = __sensor_init(sd);
> +
> + if (ret < 0)
> + dev_err(&client->dev,
> + "Camera not available! Check Power!\n");
> + } else {
> + dev_dbg(&client->dev, "OV5647 power off!\n");
> +
> + dev_dbg(&client->dev, "disable oe\n");
> + ret = ov5647_write_array(sd, sensor_oe_disable_regs,
> + ARRAY_SIZE(sensor_oe_disable_regs));
> +
> + if (ret < 0)
> + dev_dbg(&client->dev, "disable oe failed!\n");
> +
> + ret = set_sw_standby(sd, true);
> +
> + if (ret < 0)
> + dev_dbg(&client->dev, "soft stby failed!\n");
dev_err for errors? Little less "!"s in the output?
> +static int sensor_get_register(struct v4l2_subdev *sd,
> + struct v4l2_dbg_register *reg)
> +{
> + unsigned char val = 0;
> + int ret;
> +
> + ret = ov5647_read(sd, reg->reg & 0xff, &val);
> + reg->val = val;
> + reg->size = 1;
> + return ret;
> +}
Filling reg->* when read failed is strange.
> +static int sensor_set_register(struct v4l2_subdev *sd,
> + const struct v4l2_dbg_register *reg)
> +{
> + ov5647_write(sd, reg->reg & 0xff, reg->val & 0xff);
> + return 0;
> +}
error handling?
Best regards,
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
On 11/15/2016 04:10 AM, Pavel Machek wrote:
> Hi!
>
>> Add support for OV5647 sensor.
>>
>
>> +static int ov5647_write(struct v4l2_subdev *sd, u16 reg, u8 val)
>> +{
>> + int ret;
>> + unsigned char data[3] = { reg >> 8, reg & 0xff, val};
>> + struct i2c_client *client = v4l2_get_subdevdata(sd);
>> +
>> + ret = i2c_master_send(client, data, 3);
>> + if (ret != 3) {
>> + dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n",
>> + __func__, reg);
>> + return ret < 0 ? ret : -EIO;
>> + }
>> + return 0;
>> +}
>
> Sorry, this is wrong. It should something <0 any time error is detected.
>
It seems to me that it does return a value < 0 each time an error is detected.
Guenter
On Tue 2016-11-15 05:50:32, Guenter Roeck wrote:
> On 11/15/2016 04:10 AM, Pavel Machek wrote:
> >Hi!
> >
> >>Add support for OV5647 sensor.
> >>
> >
> >>+static int ov5647_write(struct v4l2_subdev *sd, u16 reg, u8 val)
> >>+{
> >>+ int ret;
> >>+ unsigned char data[3] = { reg >> 8, reg & 0xff, val};
> >>+ struct i2c_client *client = v4l2_get_subdevdata(sd);
> >>+
> >>+ ret = i2c_master_send(client, data, 3);
> >>+ if (ret != 3) {
> >>+ dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n",
> >>+ __func__, reg);
> >>+ return ret < 0 ? ret : -EIO;
> >>+ }
> >>+ return 0;
> >>+}
> >
> >Sorry, this is wrong. It should something <0 any time error is detected.
> >
>
> It seems to me that it does return a value < 0 each time an error is detected.
Yep, you are right, sorry, I misparsed the code.
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
On Mon, Nov 14, 2016 at 01:46:32PM +0000, Ramiro Oliveira wrote:
> Add device tree documentation.
>
> Signed-off-by: Ramiro Oliveira <[email protected]>
> ---
> .../devicetree/bindings/media/i2c/ov5647.txt | 19 +++++++++++++++++++
> 1 file changed, 19 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5647.txt
Acked-by: Rob Herring <[email protected]>
Hi Pavel!
On 11/15/2016 12:10 PM, Pavel Machek wrote:
> Hi!
>
>> Add support for OV5647 sensor.
>>
>
>> +static int ov5647_write(struct v4l2_subdev *sd, u16 reg, u8 val)
>> +{
>> + int ret;
>> + unsigned char data[3] = { reg >> 8, reg & 0xff, val};
>> + struct i2c_client *client = v4l2_get_subdevdata(sd);
>> +
>> + ret = i2c_master_send(client, data, 3);
>> + if (ret != 3) {
>> + dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n",
>> + __func__, reg);
>> + return ret < 0 ? ret : -EIO;
>> + }
>> + return 0;
>> +}
>
> Sorry, this is wrong. It should something <0 any time error is detected.
>
>> +static int ov5647_write_array(struct v4l2_subdev *sd,
>> + struct regval_list *regs, int array_size)
>> +{
>> + int i = 0;
>> + int ret = 0;
>> +
>> + if (!regs)
>> + return -EINVAL;
>> +
>> + while (i < array_size) {
>> + ret = ov5647_write(sd, regs->addr, regs->data);
>> + if (ret < 0)
>> + return ret;
>> + i++;
>> + regs++;
>> + }
>> + return 0;
>> +}
>
> For example this expects <0 on error.
>
>> +static int set_sw_standby(struct v4l2_subdev *sd, bool standby)
>> +{
>> + int ret;
>> + unsigned char rdval;
>> +
>> + ret = ov5647_read(sd, 0x0100, &rdval);
>> + if (ret != 0)
>> + return ret;
>> +
>> + if (standby)
>> + ret = ov5647_write(sd, 0x0100, rdval&0xfe);
>> + else
>> + ret = ov5647_write(sd, 0x0100, rdval|0x01);
>> +
>> + return ret;
>
> if (standby)
> rdval &= 0xfe;
> else
> rdval |= 0x01;
>
> ret = ov5647_write(sd, 0x0100, rdval);
>
> ?
>
>
>> +/**
>> + * @short Store information about the video data format.
>> + */
>> +static struct sensor_format_struct {
>> + __u8 *desc;
>> + u32 mbus_code;
>
> u8 is suitable here.
>
>
>> + ov5647_read(sd, 0x0100, &resetval);
>> + if (!resetval&0x01) {
>
> add ()s here.
>
>> +static int sensor_power(struct v4l2_subdev *sd, int on)
>> +{
>> + int ret;
>> + struct ov5647 *ov5647 = to_state(sd);
>> + struct i2c_client *client = v4l2_get_subdevdata(sd);
>> +
>> + ret = 0;
>> + mutex_lock(&ov5647->lock);
>> +
>> + if (on) {
>> + dev_dbg(&client->dev, "OV5647 power on!\n");
>> +
>> + ret = ov5647_write_array(sd, sensor_oe_enable_regs,
>> + ARRAY_SIZE(sensor_oe_enable_regs));
>> +
>> + ret = __sensor_init(sd);
>> +
>> + if (ret < 0)
>> + dev_err(&client->dev,
>> + "Camera not available! Check Power!\n");
>> + } else {
>> + dev_dbg(&client->dev, "OV5647 power off!\n");
>> +
>> + dev_dbg(&client->dev, "disable oe\n");
>> + ret = ov5647_write_array(sd, sensor_oe_disable_regs,
>> + ARRAY_SIZE(sensor_oe_disable_regs));
>> +
>> + if (ret < 0)
>> + dev_dbg(&client->dev, "disable oe failed!\n");
>> +
>> + ret = set_sw_standby(sd, true);
>> +
>> + if (ret < 0)
>> + dev_dbg(&client->dev, "soft stby failed!\n");
>
> dev_err for errors? Little less "!"s in the output?
>
>> +static int sensor_get_register(struct v4l2_subdev *sd,
>> + struct v4l2_dbg_register *reg)
>> +{
>> + unsigned char val = 0;
>> + int ret;
>> +
>> + ret = ov5647_read(sd, reg->reg & 0xff, &val);
>> + reg->val = val;
>> + reg->size = 1;
>> + return ret;
>> +}
>
> Filling reg->* when read failed is strange.
>
>> +static int sensor_set_register(struct v4l2_subdev *sd,
>> + const struct v4l2_dbg_register *reg)
>> +{
>> + ov5647_write(sd, reg->reg & 0xff, reg->val & 0xff);
>> + return 0;
>> +}
>
> error handling?
>
> Best regards,
> Pavel
>
Thanks for the feedback, I've corrected all the issues you pointed out, except
the one regarding the error handling in the ov5647_write function.
Best Regards,
Ramiro