From: Reinhold Mueller <[email protected]>
This patchset adds support for the emtrion emCON-MX8M Mini
Changes
v3:
[PATCH 1/2]
- no fixes, Acked-by: Rob Herring <[email protected]>
[PATCH 2/2]
- inserted hyphen in some node names
- spell out regulator in some regulator nodes
- order of properties
- sort label node alphabetically
- inserting space before node name
v2:
[PATCH 1/2]
- no fixes
[PATCH 2/2]
- replaced GPIO_ACTIVE_LOW by IRQ_TYPE_LEVEL_LOW
v1:
[PATCH 0/2]
- split former patch in dts -and yaml patches
[PATCH 1/2]
- removing character '\t'
[PATCH 2/2]
- correct entry compatible in spi-flash@0
Reinhold Mueller (2):
dt-bindings: arm: Add emtrion hardware emCON-MX8M Mini
arm64: dts: imx8mm: Add support for emtrion emCON-MX8M Mini
.../devicetree/bindings/arm/fsl.yaml | 1 +
arch/arm64/boot/dts/freescale/Makefile | 3 +-
.../boot/dts/freescale/imx8mm-emcon-avari.dts | 23 +
.../dts/freescale/imx8mm-emcon-avari.dtsi | 139 ++++
.../boot/dts/freescale/imx8mm-emcon.dtsi | 645 ++++++++++++++++++
5 files changed, 810 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi
--
2.20.1
From: Reinhold Mueller <[email protected]>
This patch presents the yaml patch for the emtrion GmbH
emCON-MX8M Mini.
Signed-off-by: Reinhold Mueller <[email protected]>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 0b595b26061f..e2c70c87baef 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -723,6 +723,7 @@ properties:
- enum:
- beacon,imx8mm-beacon-kit # i.MX8MM Beacon Development Kit
- boundary,imx8mm-nitrogen8mm # i.MX8MM Nitrogen Board
+ - emtrion,emcon-mx8mm-avari # emCON-MX8MM SoM on Avari Base
- fsl,imx8mm-ddr4-evk # i.MX8MM DDR4 EVK Board
- fsl,imx8mm-evk # i.MX8MM EVK Board
- gw,imx8mm-gw71xx-0x # i.MX8MM Gateworks Development Kit
--
2.20.1
From: Reinhold Mueller <[email protected]>
This patch adds support for the emtrion GmbH emCON-MX8M Mini modules.
They are available with NXP i.MX 8M Mini equipped with 2 or 4 GB Memory.
The devicetree imx8mm-emcon.dtsi is the common part providing all
module components and the basic support for the SoC. The support for the
avari baseboard in the developer-kit configuration is provided by the
emcon-avari dts files.
Signed-off-by: Reinhold Mueller <[email protected]>
---
arch/arm64/boot/dts/freescale/Makefile | 3 +-
.../boot/dts/freescale/imx8mm-emcon-avari.dts | 23 +
.../dts/freescale/imx8mm-emcon-avari.dtsi | 139 ++++
.../boot/dts/freescale/imx8mm-emcon.dtsi | 645 ++++++++++++++++++
4 files changed, 809 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a14a6173b765..a09b5e4d5a45 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -34,8 +34,9 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-qds.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
-dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dts b/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dts
new file mode 100644
index 000000000000..b2e8967e9687
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright (c) 2021 emtrion GmbH
+// Author: Frank Erdrich <[email protected]>
+//
+
+/dts-v1/;
+
+#include "imx8mm-emcon.dtsi"
+#include "imx8mm-emcon-avari.dtsi"
+
+/ {
+ model = "emtrion SoM emCON-MX8M mini on Avari";
+ compatible = "emtrion,emcon-mx8mm-avari", "fsl,imx8mm";
+};
+
+&lvds_backlight {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dtsi
new file mode 100644
index 000000000000..5028f232b6bd
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dtsi
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright (C) 2021 emtrion GmbH
+// Author: Frank Erdrich <[email protected]>
+//
+
+/ {
+ aliases {
+ boardid = &boardID;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ reg_wall_5p0: regulator-wall5p0 {
+ compatible = "regulator-fixed";
+ regulator-name = "Main-Supply";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_base3p3: regulator-base3p3 {
+ compatible = "regulator-fixed";
+ vin-supply = <®_wall_5p0>;
+ regulator-name = "3V3-avari";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_base1p5: regulator-base1p5 {
+ compatible = "regulator-fixed";
+ vin-supply = <®_base3p3>;
+ regulator-name = "1V5-avari";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_usb_otg: regulator-otgvbus {
+ compatible = "regulator-fixed";
+ vin-supply = <®_wall_5p0>;
+ regulator-name = "OTG_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ regulator-always-on;
+ };
+
+ clk_codec: clock-codec {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <12000000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "SGTL5000-Card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&codec_dai>;
+ simple-audio-card,frame-master = <&codec_dai>;
+ simple-audio-card,widgets = "Headphone", "Headphone Jack";
+ simple-audio-card,routing = "Headphone Jack", "HP_OUT";
+
+ cpu_dai: simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ };
+
+ codec_dai: simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ };
+ };
+};
+
+&ecspi1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ sgtl5000: audio-codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ clocks = <&clk_codec>;
+ VDDA-supply = <®_base3p3>;
+ VDDIO-supply = <®_base3p3>;
+ };
+
+ boardID: gpio@3a {
+ compatible = "nxp,pca8574";
+ reg = <0x3a>;
+ gpio-controller;
+ #gpio-cells = <1>;
+ };
+};
+
+&sai2 {
+ status = "okay";
+};
+
+&uart2 {
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&usbotg1 {
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ status = "disabled";
+};
+
+&usdhc2 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi
new file mode 100644
index 000000000000..a430d092f7ce
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi
@@ -0,0 +1,645 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright 2018 NXP
+// Copyright (C) 2021 emtrion GmbH
+//
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ rpmsg_reserved: rpmsg@b8000000 {
+ no-map;
+ reg = <0 0xb8000000 0 0x400000>;
+ };
+
+ loader_reserved: loader@bb700000 {
+ no-map;
+ reg = <0 0xbb700000 0x0 0x00100000>;
+ };
+
+ pci_reserved: pci@bb800000 {
+ no-map;
+ reg = <0 0xbb800000 0x0 0x00200000>;
+ };
+
+ ivshmem2_reserved: ivshmem2@bba00000 {
+ no-map;
+ reg = <0 0xbba00000 0x0 0x00100000>;
+ };
+
+ ivshmem_reserved: ivshmem@bbb00000 {
+ no-map;
+ reg = <0 0xbbb00000 0x0 0x00100000>;
+ };
+ };
+
+ som_leds: leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_led>;
+
+ green {
+ label = "som:green";
+ gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ red {
+ label = "som:red";
+ gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ lvds_backlight: lvds-backlight {
+ compatible = "pwm-backlight";
+ enable-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+ pwms = <&pwm1 0 50000 0>;
+ brightness-levels = <
+ 0 4 8 16 32 64 80 96 112
+ 128 144 160 176 250
+ >;
+ default-brightness-level = <9>;
+ status = "disabled";
+ };
+
+ reg_usdhc1_vmmc: regulator-emmc {
+ compatible = "regulator-fixed";
+ regulator-name = "eMMC";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_usdhc2_vmmc: regulator-usdhc2 {
+ compatible = "regulator-fixed";
+ regulator-name = "sdcard_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-reset-gpios = <&gpio1 9 0>;
+ fsl,magic-packet;
+ status = "okay";
+};
+
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi0>;
+ pinctrl-1 = <&pinctrl_flexspi1>;
+ status = "okay";
+
+ flash0: spi-flash@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_csi_pwn: csi-pwn-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x82
+ MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82
+ MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x82
+ >;
+ };
+
+ pinctrl_ecspi1_cs: ecspi1-cs {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x40000
+ MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x40000
+ >;
+ };
+
+ pinctrl_fec1: fec1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ >;
+ };
+
+ pinctrl_flexspi0: flexspi0-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2
+ MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
+ MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
+ MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
+ MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
+ MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS 0x82
+ >;
+ };
+
+ pinctrl_flexspi1: flexspi1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_CLE_QSPI_B_SCLK 0x1c2
+ MX8MM_IOMUXC_NAND_CE2_B_QSPI_B_SS0_B 0x82
+ MX8MM_IOMUXC_NAND_DATA04_QSPI_B_DATA0 0x82
+ MX8MM_IOMUXC_NAND_DATA05_QSPI_B_DATA1 0x82
+ MX8MM_IOMUXC_NAND_DATA06_QSPI_B_DATA2 0x82
+ MX8MM_IOMUXC_NAND_DATA07_QSPI_B_DATA3 0x82
+ >;
+ };
+
+ pinctrl_gpio_led: gpio-led-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI2_SCLK_GPIO5_IO10 0x19
+ MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_i2c3: i2c3-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
+ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_lvds: lvds-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x06
+ >;
+ };
+
+ pinctrl_pcie0: pcie0-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x41
+ MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x41
+ >;
+ };
+
+ pinctrl_pmic: pmic-irq {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x41
+ >;
+ };
+
+ pinctrl_pwm1: pwm1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT 0x06
+ >;
+ };
+
+ pinctrl_sai2: sai2-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6
+ MX8MM_IOMUXC_SAI2_RXC_SAI2_RX_BCLK 0xd6
+ MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6
+ MX8MM_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC 0xd6
+ MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6
+ MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6
+ MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6
+ >;
+ };
+
+ pinctrl_spdif1: spdif1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6
+ MX8MM_IOMUXC_SPDIF_RX_SPDIF1_IN 0xd6
+ >;
+ };
+
+ pinctrl_uart1: uart1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
+ MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_uart2: uart2-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
+ MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
+
+ /* rts and cts */
+ MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140
+ MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140
+ >;
+ };
+
+ pinctrl_uart3: uart3-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140
+ MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_uart4: uart4-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140
+ MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
+ MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
+ MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
+ MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
+ MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
+ MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
+ MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6
+ MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6
+ MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6
+ MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6
+ >;
+ };
+
+ pinctrl_usdhc1_gpio: usdhc1-gpio-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x41
+ MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c4
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
+ >;
+ };
+
+ /* no reset for sdhc2 interface */
+ pinctrl_usdhc2_gpio: usdhc2-gpio-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4
+ MX8MM_IOMUXC_SD2_WP_USDHC2_WP 0x1c4
+ >;
+ };
+
+ pinctrl_wdog: wdog-grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ bd71847: pmic@4b {
+ compatible = "rohm,bd71847";
+ reg = <0x4b>;
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ rohm,reset-snvs-powered;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3_reg: BUCK3 {
+ // BUCK5 in datasheet
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ // BUCK6 in datasheet
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ // BUCK7 in datasheet
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ // BUCK8 in datasheet
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "LDO6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ rv1805: rtc@69 {
+ compatible = "abracon,ab1805";
+ reg = <0x69>;
+ };
+};
+
+&mu {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&sai2 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2>;
+ assigned-clocks = <&clk IMX8MM_CLK_SAI2>;
+ assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <12000000>;
+ status = "disabled";
+};
+
+&spdif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif1>;
+ assigned-clocks = <&clk IMX8MM_CLK_SPDIF1>;
+ assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ clocks = <&clk IMX8MM_CLK_AUDIO_AHB>, <&clk IMX8MM_CLK_24M>,
+ <&clk IMX8MM_CLK_SPDIF1>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_AUDIO_AHB>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_AUDIO_PLL1_OUT>, <&clk IMX8MM_AUDIO_PLL2_OUT>;
+ clock-names = "core", "rxtx0", "rxtx1", "rxtx2", "rxtx3",
+ "rxtx4", "rxtx5", "rxtx6", "rxtx7", "spba", "pll8k", "pll11k";
+ status = "disabled";
+};
+
+&uart1 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ assigned-clocks = <&clk IMX8MM_CLK_UART3>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ assigned-clocks = <&clk IMX8MM_CLK_UART4>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ over-current-active-low;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "disabled";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
+ bus-width = <8>;
+ vmmc-supply = <®_usdhc1_vmmc>;
+ keep-power-in-suspend;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
--
2.20.1
Hi Reinhold,
On Thu, Dec 16, 2021 at 1:59 PM <[email protected]> wrote:
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + rpmsg_reserved: rpmsg@b8000000 {
> + no-map;
> + reg = <0 0xb8000000 0 0x400000>;
> + };
> +
> + loader_reserved: loader@bb700000 {
> + no-map;
> + reg = <0 0xbb700000 0x0 0x00100000>;
> + };
> +
> + pci_reserved: pci@bb800000 {
> + no-map;
> + reg = <0 0xbb800000 0x0 0x00200000>;
> + };
> +
> + ivshmem2_reserved: ivshmem2@bba00000 {
> + no-map;
> + reg = <0 0xbba00000 0x0 0x00100000>;
> + };
> +
> + ivshmem_reserved: ivshmem@bbb00000 {
> + no-map;
> + reg = <0 0xbbb00000 0x0 0x00100000>;
> + };
> + };
Are these reserved nodes needed with mainline?
Looks like they are remnants from NXP vendor BSP.
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-id";
> + phy-reset-gpios = <&gpio1 9 0>;
phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
Actually, phy-reset-gpios is considered deprecated.
You could also add an mdio node as fec child and:
add reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; there.
Hi Fabio,
thanks for the feedback.
Please see the comments at the marked issues below.
I will send a new patchset.
Regards
Reinhold
Reinhold Mueller
Software engineer
emtrion GmbH
Am Hasenbiel 6 | 76297 Stutensee | Germany
Phone +49 7244 62694 20
Fax +49 7244 62694 19
Email [email protected]
Online http://www.emtrion.de
*** Merry X-Mas & Happy New Year 2022 ***
emtrion GmbH • Amtsgericht Mannheim • HRB 110 300 • Geschäftsführer: Ramona Maurer, Achmed Haddou • Umsatzsteueridentifikationsnummer:DE813694260 • Impressum: http://www.emtrion.de/de/impressum.html
HINWEIS: Personenbezogene Daten, die Sie per E-Mail an uns übermitteln, werden bei uns gespeichert und verarbeitet. Informationen zu unseren gesetzlichen Informationspflichten, zu uns und unseren Dienstleistungen finden Sie in unseren Datenschutzhinweisen.
Diese E-Mail kann vertrauliche und / oder rechtlich geschützte Informationen enthalten. Wenn Sie nicht der richtige Adressat sind, oder diese E-Mail irrtümlich erhalten haben, informieren Sie bitte den Absender und vernichten diese Mail. Das unerlaubte kopieren, sowie die unbefugte Weitergabe dieser Mail ist nicht gestattet.
> -----Ursprüngliche Nachricht-----
> Von: Fabio Estevam <[email protected]>
> Gesendet: Donnerstag, 16. Dezember 2021 18:19
> An: Mueller, Reinhold <[email protected]>
> Cc: Shawn Guo <[email protected]>; Rob Herring
> <[email protected]>; Sascha Hauer <[email protected]>; Sascha
> Hauer <[email protected]>; NXP Linux Team <[email protected]>;
> open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <[email protected]>; linux-kernel <[email protected]>
> Betreff: Re: [PATCH v3 2/2] arm64: dts: imx8mm: Add support for emtrion
> emCON-MX8M Mini
>
> Hi Reinhold,
>
> On Thu, Dec 16, 2021 at 1:59 PM <[email protected]> wrote:
>
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + rpmsg_reserved: rpmsg@b8000000 {
> > + no-map;
> > + reg = <0 0xb8000000 0 0x400000>;
> > + };
> > +
> > + loader_reserved: loader@bb700000 {
> > + no-map;
> > + reg = <0 0xbb700000 0x0 0x00100000>;
> > + };
> > +
> > + pci_reserved: pci@bb800000 {
> > + no-map;
> > + reg = <0 0xbb800000 0x0 0x00200000>;
> > + };
> > +
> > + ivshmem2_reserved: ivshmem2@bba00000 {
> > + no-map;
> > + reg = <0 0xbba00000 0x0 0x00100000>;
> > + };
> > +
> > + ivshmem_reserved: ivshmem@bbb00000 {
> > + no-map;
> > + reg = <0 0xbbb00000 0x0 0x00100000>;
> > + };
> > + };
>
> Are these reserved nodes needed with mainline?
>
> Looks like they are remnants from NXP vendor BSP.
>
The reserved memory nodes are more custom specific, so i remove it from the tree.
> > +&fec1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fec1>;
> > + phy-mode = "rgmii-id";
> > + phy-reset-gpios = <&gpio1 9 0>;
>
> phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
>
> Actually, phy-reset-gpios is considered deprecated.
>
> You could also add an mdio node as fec child and:
> add reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; there.
Ok, i will add a child in fec fort he reset gpios