This commit adds initial dt support for the rk3399 based Pinebook Pro.
Signed-off-by: Tobias Schramm <[email protected]>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3399-pinebook-pro.dts | 1105 +++++++++++++++++
2 files changed, 1106 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 60d9437096c7..ae7621309e92 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
new file mode 100644
index 000000000000..dfade7e00051
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
@@ -0,0 +1,1105 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2018 Akash Gajjar <[email protected]>
+ * Copyright (c) 2020 Tobias Schramm <[email protected]>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/common.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+ model = "Pine64 Pinebook Pro";
+ compatible = "pine64,pinebook-pro", "rockchip,rk3399";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ backlight: edp-backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&vcc_12v>;
+ pwms = <&pwm0 0 740740 0>;
+ };
+
+ edp_panel: edp-panel {
+ compatible = "boe,nv140fhmn49";
+ backlight = <&backlight>;
+ enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_en_gpio>;
+ power-supply = <&vcc3v3_panel>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ panel_in_edp: endpoint@0 {
+ remote-endpoint = <&edp_out_panel>;
+ };
+ };
+ };
+ };
+
+ /*
+ * Use separate nodes for gpio-keys to allow for selective deactivation
+ * of wakeup sources via sysfs without disabling the whole key
+ */
+ gpio-key-lid {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lidbtn_gpio>;
+
+ lid {
+ debounce-interval = <20>;
+ gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_LOW>;
+ label = "Lid";
+ linux,code = <SW_LID>;
+ linux,input-type = <EV_SW>;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ wakeup-source;
+ };
+ };
+
+ gpio-key-power {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrbtn_gpio>;
+
+ power {
+ debounce-interval = <20>;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "Power";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrled_gpio &slpled_gpio>;
+
+ green-led {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ label = "green:power";
+ };
+
+ red-led {
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ function = LED_FUNCTION_STANDBY;
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ label = "red:standby";
+ panic-indicator;
+ retain-state-suspended;
+ };
+ };
+
+ /* Power sequence for SDIO WiFi module */
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk808 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h_gpio>;
+ post-power-on-delay-ms = <100>;
+ power-off-delay-us = <500000>;
+
+ /* WL_REG_ON on module */
+ reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+ };
+
+ /* Audio components */
+ es8316-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_det_gpio>;
+ simple-audio-card,name = "rockchip,es8316-codec";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Speaker";
+ simple-audio-card,routing =
+ "MIC1", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Speaker Amplifier INL", "HPOL",
+ "Speaker Amplifier INR", "HPOR",
+ "Speaker", "Speaker Amplifier OUTL",
+ "Speaker", "Speaker Amplifier OUTR";
+
+ simple-audio-card,hp-det-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
+ simple-audio-card,aux-devs = <&speaker_amp>;
+ simple-audio-card,pin-switches = "Speaker";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&es8316>;
+ };
+ };
+
+ speaker_amp: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ enable-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_HIGH>;
+ sound-name-prefix = "Speaker Amplifier";
+ VCC-supply = <&pa_5v>;
+ };
+
+ /* Power tree */
+ /* Root power source */
+ vcc_sysin: vcc-sysin {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_sysin";
+ };
+
+ /* Regulators supplied by vcc_sysin */
+ /* LCD backlight supply */
+ vcc_12v: vcc-12v {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-name = "vcc_12v";
+ vin-supply = <&vcc_sysin>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* Main 3.3 V supply */
+ vcc3v3_sys: wifi_bat: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_sys";
+ vin-supply = <&vcc_sysin>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ /* 5 V USB power supply */
+ vcc5v0_usb: pa_5v: vcc5v0-usb-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_5v_gpio>;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vcc5v0_usb";
+ vin-supply = <&vcc_sysin>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* RK3399 logic supply */
+ vdd_log: vdd-log {
+ compatible = "pwm-regulator";
+ pwms = <&pwm2 0 25000 1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd_log";
+ vin-supply = <&vcc_sysin>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ /* Regulators supplied by vcc3v3_sys */
+ /* 0.9 V supply, always on */
+ vcc_0v9: vcc-0v9 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vcc_0v9";
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ /* S3 1.8 V supply, switched by vcc1v8_s3 */
+ vcca1v8_s3: vcc1v8-s3 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_s3";
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ /* micro SD card power */
+ vcc3v0_sd: vcc3v0-sd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_pwr_h_gpio>;
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc3v0_sd";
+ vin-supply = <&vcc3v3_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* LCD panel power, called VCC3V3_S0 in schematic */
+ vcc3v3_panel: vcc3v3-panel {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdvcc_en_gpio>;
+ regulator-always-on;
+ regulator-enable-ramp-delay = <100000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_panel";
+ vin-supply = <&vcc3v3_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* M.2 adapter power, switched by vcc1v8_s3 */
+ vcc3v3_ssd: vcc3v3-ssd {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_ssd";
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ /* Regulators supplied by vcc5v0_usb */
+ /* USB 3 port power supply regulator */
+ vcc5v0_otg: vcc5v0-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en_gpio>;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vcc5v0_otg";
+ vin-supply = <&vcc5v0_usb>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* Regulators supplied by vcc5v0_usb */
+ /* Type C port power supply regulator */
+ vbus_5vout: vbus_typec: vbus-5vout {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_typec0_en_gpio>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vbus_5vout";
+ vin-supply = <&vcc5v0_usb>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* Regulators supplied by vcc_1v8 */
+ /* Primary 0.9 V LDO */
+ vcca0v9_s3: vcca0v9-s3 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "vcc0v9_s3";
+ vin-supply = <&vcc_1v8>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ mains_charger: dc-charger {
+ compatible = "gpio-charger";
+ charger-type = "mains";
+ gpios = <&gpio4 RK_PD0 GPIO_ACTIVE_LOW>;
+
+ /* Also triggered by USB charger */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dc_det_gpio>;
+ };
+};
+
+&cdn_dp {
+ status = "okay";
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&edp {
+ force-hpd;
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_hpd>;
+ status = "okay";
+
+ ports {
+ edp_out: port@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ edp_out_panel: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_in_edp>;
+ };
+ };
+ };
+};
+
+&emmc_phy {
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ i2c-scl-rising-time-ns = <168>;
+ i2c-scl-falling-time-ns = <4>;
+ status = "okay";
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+ interrupt-parent = <&gpio3>;
+ interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l_gpio>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sysin>;
+ vcc2-supply = <&vcc_sysin>;
+ vcc3-supply = <&vcc_sysin>;
+ vcc4-supply = <&vcc_sysin>;
+ vcc6-supply = <&vcc_sysin>;
+ vcc7-supply = <&vcc_sysin>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc_sysin>;
+ vcc10-supply = <&vcc_sysin>;
+ vcc11-supply = <&vcc_sysin>;
+ vcc12-supply = <&vcc3v3_sys>;
+ vcc13-supply = <&vcc_sysin>;
+ vcc14-supply = <&vcc_sysin>;
+
+ regulators {
+ /* rk3399 center logic supply */
+ vdd_center: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_center";
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_l: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_cpu_l";
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v8: vcc_wl: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ /* not used */
+ LDO_REG1 {
+ };
+
+ /* not used */
+ LDO_REG2 {
+ };
+
+ vcc1v8_pmupll: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8_pmupll";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_sdio: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc_sdio";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcca3v0_codec: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcca3v0_codec";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v5: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc_1v5";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1500000>;
+ };
+ };
+
+ vcca1v8_codec: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_codec";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v0: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc_3v0";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc3v3_s3: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s3";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_s0: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc3v3_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+
+ vdd_cpu_b: regulator@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel1_gpio>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-compatible = "fan53555-reg";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd_cpu_b";
+ regulator-ramp-delay = <1000>;
+ vin-supply = <&vcc_1v8>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: regulator@41 {
+ compatible = "silergy,syr828";
+ reg = <0x41>;
+ fcs,suspend-voltage-selector = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel2_gpio>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-compatible = "fan53555-reg";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd_gpu";
+ regulator-ramp-delay = <1000>;
+ vin-supply = <&vcc_1v8>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ i2c-scl-falling-time-ns = <4>;
+ i2c-scl-rising-time-ns = <168>;
+ status = "okay";
+
+ es8316: es8316@11 {
+ compatible = "everest,es8316";
+ reg = <0x11>;
+ clocks = <&cru SCLK_I2S_8CH_OUT>;
+ clock-names = "mclk";
+ #sound-dai-cells = <0>;
+ };
+};
+
+&i2c3 {
+ i2c-scl-falling-time-ns = <15>;
+ i2c-scl-rising-time-ns = <450>;
+ status = "okay";
+};
+
+&i2c4 {
+ i2c-scl-falling-time-ns = <20>;
+ i2c-scl-rising-time-ns = <600>;
+ status = "okay";
+
+ fusb0: fusb30x@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ fcs,int_n = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&fusb0_int_gpio>;
+ status = "okay";
+ vbus-supply = <&vbus_typec>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ op-sink-microwatt = <1000000>;
+ power-role = "dual";
+ sink-pdos =
+ <PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
+ source-pdos =
+ <PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>;
+ try-power-role = "sink";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ usbc_hs: endpoint {
+ remote-endpoint =
+ <&u2phy0_typec_hs>;
+ };
+ };
+
+ port@1 {
+ usbc_ss: endpoint {
+ remote-endpoint =
+ <&tcphy0_typec_ss>;
+ };
+ };
+
+ port@2 {
+ usbc_dp: endpoint {
+ remote-endpoint =
+ <&tcphy0_typec_dp>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2s1 {
+ #sound-dai-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s_8ch_mclk_gpio>, <&i2s1_2ch_bus>;
+ rockchip,playback-channels = <8>;
+ rockchip,capture-channels = <8>;
+ status = "okay";
+};
+
+&io_domains {
+ audio-supply = <&vcc_3v0>;
+ gpio1830-supply = <&vcc_3v0>;
+ sdmmc-supply = <&vcc_sdio>;
+ status = "okay";
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ bus-scan-delay-ms = <1000>;
+ ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+ max-link-speed = <2>;
+ num-lanes = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreqn_cpm>;
+ vpcie0v9-supply = <&vcca0v9_s3>;
+ vpcie1v8-supply = <&vcca1v8_s3>;
+ vpcie3v3-supply = <&vcc3v3_ssd>;
+ status = "okay";
+};
+
+&pinctrl {
+ buttons {
+ pwrbtn_gpio: pwrbtn-gpio {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ lidbtn_gpio: lidbtn-gpio {
+ rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ dc-charger {
+ dc_det_gpio: dc-det-gpio {
+ rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ es8316 {
+ hp_det_gpio: hp-det-gpio {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ fusb302x {
+ fusb0_int_gpio: fusb0-int-gpio {
+ rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ i2s1 {
+ i2s_8ch_mclk_gpio: i2s-8ch-mclk-gpio {
+ rockchip,pins = <4 RK_PA0 1 &pcfg_pull_none>;
+ };
+ };
+
+ lcd-panel {
+ lcdvcc_en_gpio: lcdvcc-en-gpio {
+ rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ panel_en_gpio: panel-en-gpio {
+ rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ lcd_panel_reset_gpio: lcd-panel-reset-gpio {
+ rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ pwrled_gpio: pwrled_gpio {
+ rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ slpled_gpio: slpled_gpio {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l_gpio: pmic-int-l-gpio {
+ rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ vsel1_gpio: vsel1-gpio {
+ rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ vsel2_gpio: vsel2-gpio {
+ rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ sdcard {
+ sdmmc0_pwr_h_gpio: sdmmc0-pwr-h-gpio {
+ rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h_gpio: wifi-enable-h-gpio {
+ rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb-typec {
+ vcc5v0_typec0_en_gpio: vcc5v0-typec0-en-gpio {
+ rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ pwr_5v_gpio: pwr-5v-gpio {
+ rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc5v0_host_en_gpio: vcc5v0-host-en-gpio {
+ rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wireless-bluetooth {
+ bt_wake_gpio: bt-wake-gpio {
+ rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ bt_host_wake_gpio: bt-host-wake-gpio {
+ rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_reset_gpio: bt-reset-gpio {
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmu1830-supply = <&vcc_3v0>;
+ status = "okay";
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca1v8_s3>;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&sdio0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ status = "okay";
+};
+
+&spi1 {
+ max-freq = <10000000>;
+ status = "okay";
+
+ spiflash: flash@0 {
+ compatible = "jedec,spi-nor";
+ m25p,fast-read;
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ loader@8000 {
+ label = "loader";
+ reg = <0x0 0x3F8000>;
+ };
+
+ env@3f8000 {
+ label = "env";
+ reg = <0x3F8000 0x8000>;
+ };
+
+ vendor@7c0000 {
+ label = "vendor";
+ reg = <0x7C0000 0x40000>;
+ };
+ };
+ };
+};
+
+&tcphy0 {
+ status = "okay";
+};
+
+&tcphy0_dp {
+ port {
+ tcphy0_typec_dp: endpoint {
+ remote-endpoint = <&usbc_dp>;
+ };
+ };
+};
+
+&tcphy0_usb3 {
+ port {
+ tcphy0_typec_ss: endpoint {
+ remote-endpoint = <&usbc_ss>;
+ };
+ };
+};
+
+&tcphy1 {
+ status = "okay";
+};
+
+&tsadc {
+ /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-mode = <1>;
+ /* tshut polarity 0:LOW 1:HIGH */
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+
+ u2phy0_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy0_host: host-port {
+ phy-supply = <&vcc5v0_otg>;
+ status = "okay";
+ };
+
+ port {
+ u2phy0_typec_hs: endpoint {
+ remote-endpoint = <&usbc_hs>;
+ };
+ };
+};
+
+&u2phy1 {
+ status = "okay";
+
+ u2phy1_otg: otg-port {
+ status = "okay";
+ };
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_otg>;
+ status = "okay";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&rk808 1>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
+ max-speed = <1500000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_gpio &bt_wake_gpio &bt_reset_gpio>;
+ shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+ vbat-supply = <&wifi_bat>;
+ vddio-supply = <&vcc_wl>;
+ };
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usbdrd3_0 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbdrd3_1 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
--
2.24.1
Hi Tobias,
Some minor style issues.
This dts file contains a partition node.
Question for the maintainers (Heiko?):
Should that partition be included or not?
On 2/29/20 3:48 PM, Tobias Schramm wrote:
> This commit adds initial dt support for the rk3399 based Pinebook Pro.
>
> Signed-off-by: Tobias Schramm <[email protected]>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3399-pinebook-pro.dts | 1105 +++++++++++++++++
> 2 files changed, 1106 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile
b/arch/arm64/boot/dts/rockchip/Makefile
> index 60d9437096c7..ae7621309e92 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
> new file mode 100644
> index 000000000000..dfade7e00051
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
> @@ -0,0 +1,1105 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
> + * Copyright (c) 2018 Akash Gajjar <[email protected]>
> + * Copyright (c) 2020 Tobias Schramm <[email protected]>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include <dt-bindings/usb/pd.h>
> +#include <dt-bindings/leds/common.h>
> +#include "rk3399.dtsi"
> +#include "rk3399-opp.dtsi"
> +
> +/ {
> + model = "Pine64 Pinebook Pro";
> + compatible = "pine64,pinebook-pro", "rockchip,rk3399";
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + backlight: edp-backlight {
> + compatible = "pwm-backlight";
> + power-supply = <&vcc_12v>;
> + pwms = <&pwm0 0 740740 0>;
> + };
> +
> + edp_panel: edp-panel {
> + compatible = "boe,nv140fhmn49";
> + backlight = <&backlight>;
> + enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&panel_en_gpio>;
> + power-supply = <&vcc3v3_panel>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port@0 {
> + panel_in_edp: endpoint@0 {
> + remote-endpoint = <&edp_out_panel>;
> + };
> + };
> + };
> + };
> +
> + /*
> + * Use separate nodes for gpio-keys to allow for selective deactivation
> + * of wakeup sources via sysfs without disabling the whole key
> + */
> + gpio-key-lid {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&lidbtn_gpio>;
> +
> + lid {
> + debounce-interval = <20>;
> + gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_LOW>;
> + label = "Lid";
> + linux,code = <SW_LID>;
> + linux,input-type = <EV_SW>;
> + wakeup-event-action = <EV_ACT_DEASSERTED>;
> + wakeup-source;
> + };
> + };
> +
> + gpio-key-power {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrbtn_gpio>;
> +
> + power {
> + debounce-interval = <20>;
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "Power";
> + linux,code = <KEY_POWER>;
> + wakeup-source;
> + };
> + };
> +
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwrled_gpio &slpled_gpio>;
> +
> + green-led {
> + color = <LED_COLOR_ID_GREEN>;
> + default-state = "on";
> + function = LED_FUNCTION_POWER;
> + gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> + label = "green:power";
> + };
> +
> + red-led {
> + color = <LED_COLOR_ID_RED>;
> + default-state = "off";
> + function = LED_FUNCTION_STANDBY;
> + gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> + label = "red:standby";
> + panic-indicator;
> + retain-state-suspended;
> + };
> + };
> +
> + /* Power sequence for SDIO WiFi module */
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk808 1>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h_gpio>;
> + post-power-on-delay-ms = <100>;
> + power-off-delay-us = <500000>;
> +
> + /* WL_REG_ON on module */
> + reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
> + };
> +
> + /* Audio components */
> + es8316-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_det_gpio>;
> + simple-audio-card,name = "rockchip,es8316-codec";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,widgets =
> + "Microphone", "Mic Jack",
> + "Headphone", "Headphones",
> + "Speaker", "Speaker";
> + simple-audio-card,routing =
> + "MIC1", "Mic Jack",
> + "Headphones", "HPOL",
> + "Headphones", "HPOR",
> + "Speaker Amplifier INL", "HPOL",
> + "Speaker Amplifier INR", "HPOR",
> + "Speaker", "Speaker Amplifier OUTL",
> + "Speaker", "Speaker Amplifier OUTR";
> +
> + simple-audio-card,hp-det-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_LOW>;
> + simple-audio-card,aux-devs = <&speaker_amp>;
> + simple-audio-card,pin-switches = "Speaker";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&es8316>;
> + };
> + };
> +
> + speaker_amp: speaker-amplifier {
> + compatible = "simple-audio-amplifier";
> + enable-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_HIGH>;
> + sound-name-prefix = "Speaker Amplifier";
> + VCC-supply = <&pa_5v>;
> + };
> +
> + /* Power tree */
> + /* Root power source */
> + vcc_sysin: vcc-sysin {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_sysin";
> + };
> +
> + /* Regulators supplied by vcc_sysin */
> + /* LCD backlight supply */
> + vcc_12v: vcc-12v {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + regulator-name = "vcc_12v";
> + vin-supply = <&vcc_sysin>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + /* Main 3.3 V supply */
> + vcc3v3_sys: wifi_bat: vcc3v3-sys {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_sys";
> + vin-supply = <&vcc_sysin>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + /* 5 V USB power supply */
> + vcc5v0_usb: pa_5v: vcc5v0-usb-regulator {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwr_5v_gpio>;
> + regulator-always-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "vcc5v0_usb";
> + vin-supply = <&vcc_sysin>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + /* RK3399 logic supply */
> + vdd_log: vdd-log {
> + compatible = "pwm-regulator";
> + pwms = <&pwm2 0 25000 1>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd_log";
> + vin-supply = <&vcc_sysin>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + /* Regulators supplied by vcc3v3_sys */
> + /* 0.9 V supply, always on */
> + vcc_0v9: vcc-0v9 {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vcc_0v9";
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + /* S3 1.8 V supply, switched by vcc1v8_s3 */
> + vcca1v8_s3: vcc1v8-s3 {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcca1v8_s3";
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + /* micro SD card power */
> + vcc3v0_sd: vcc3v0-sd {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0_pwr_h_gpio>;
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcc3v0_sd";
> + vin-supply = <&vcc3v3_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + /* LCD panel power, called VCC3V3_S0 in schematic */
> + vcc3v3_panel: vcc3v3-panel {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcdvcc_en_gpio>;
> + regulator-always-on;
> + regulator-enable-ramp-delay = <100000>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_panel";
> + vin-supply = <&vcc3v3_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + /* M.2 adapter power, switched by vcc1v8_s3 */
> + vcc3v3_ssd: vcc3v3-ssd {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc3v3_ssd";
> + vin-supply = <&vcc3v3_sys>;
> + };
> +
> + /* Regulators supplied by vcc5v0_usb */
> + /* USB 3 port power supply regulator */
> + vcc5v0_otg: vcc5v0-otg {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_host_en_gpio>;
> + regulator-always-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "vcc5v0_otg";
> + vin-supply = <&vcc5v0_usb>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + /* Regulators supplied by vcc5v0_usb */
> + /* Type C port power supply regulator */
> + vbus_5vout: vbus_typec: vbus-5vout {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_typec0_en_gpio>;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "vbus_5vout";
> + vin-supply = <&vcc5v0_usb>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + /* Regulators supplied by vcc_1v8 */
> + /* Primary 0.9 V LDO */
> + vcca0v9_s3: vcca0v9-s3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "vcc0v9_s3";
> + vin-supply = <&vcc_1v8>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + mains_charger: dc-charger {
> + compatible = "gpio-charger";
> + charger-type = "mains";
> + gpios = <&gpio4 RK_PD0 GPIO_ACTIVE_LOW>;
> +
> + /* Also triggered by USB charger */
> + pinctrl-names = "default";
> + pinctrl-0 = <&dc_det_gpio>;
> + };
> +};
> +
> +&cdn_dp {
> + status = "okay";
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_l>;
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_b>;
> +};
sort and move above &cpu_l0
> +
> +&edp {
> + force-hpd;
> + pinctrl-names = "default";
> + pinctrl-0 = <&edp_hpd>;
> + status = "okay";
> +
> + ports {
> + edp_out: port@1 {
> + reg = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + edp_out_panel: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&panel_in_edp>;
> + };
> + };
> + };
> +};
> +
> +&emmc_phy {
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu>;
> + status = "okay";
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <168>;
> + i2c-scl-falling-time-ns = <4>;
sort this as well
> + status = "okay";
> +
> + rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + reg = <0x1b>;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k", "rk808-clkout2";
> + interrupt-parent = <&gpio3>;
> + interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l_gpio>;
> + rockchip,system-power-controller;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc_sysin>;
> + vcc2-supply = <&vcc_sysin>;
> + vcc3-supply = <&vcc_sysin>;
> + vcc4-supply = <&vcc_sysin>;
> + vcc6-supply = <&vcc_sysin>;
> + vcc7-supply = <&vcc_sysin>;
> + vcc8-supply = <&vcc3v3_sys>;
> + vcc9-supply = <&vcc_sysin>;
> + vcc10-supply = <&vcc_sysin>;
> + vcc11-supply = <&vcc_sysin>;
> + vcc12-supply = <&vcc3v3_sys>;
> + vcc13-supply = <&vcc_sysin>;
> + vcc14-supply = <&vcc_sysin>;
> +
> + regulators {
> + /* rk3399 center logic supply */
> + vdd_center: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "vdd_center";
> + regulator-ramp-delay = <6001>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_l: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "vdd_cpu_l";
> + regulator-ramp-delay = <6001>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc_ddr";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v8: vcc_wl: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + /* not used */
> + LDO_REG1 {
> + };
> +
> + /* not used */
> + LDO_REG2 {
> + };
> +
> + vcc1v8_pmupll: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc1v8_pmupll";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_sdio: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcc_sdio";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcca3v0_codec: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcca3v0_codec";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v5: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "vcc_1v5";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1500000>;
> + };
> + };
> +
> + vcca1v8_codec: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcca1v8_codec";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_3v0: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcc_3v0";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> +
> + vcc3v3_s3: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc3v3_s3";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_s0: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vcc3v3_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> +
> + vdd_cpu_b: regulator@40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel1_gpio>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-compatible = "fan53555-reg";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "vdd_cpu_b";
> + regulator-ramp-delay = <1000>;
> + vin-supply = <&vcc_1v8>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: regulator@41 {
> + compatible = "silergy,syr828";
> + reg = <0x41>;
> + fcs,suspend-voltage-selector = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vsel2_gpio>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-compatible = "fan53555-reg";
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "vdd_gpu";
> + regulator-ramp-delay = <1000>;
> + vin-supply = <&vcc_1v8>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + i2c-scl-falling-time-ns = <4>;
> + i2c-scl-rising-time-ns = <168>;
> + status = "okay";
> +
> + es8316: es8316@11 {
> + compatible = "everest,es8316";
> + reg = <0x11>;
> + clocks = <&cru SCLK_I2S_8CH_OUT>;
> + clock-names = "mclk";
> + #sound-dai-cells = <0>;
> + };
> +};
> +
> +&i2c3 {
> + i2c-scl-falling-time-ns = <15>;
> + i2c-scl-rising-time-ns = <450>;
> + status = "okay";
> +};
> +
> +&i2c4 {
> + i2c-scl-falling-time-ns = <20>;
> + i2c-scl-rising-time-ns = <600>;
> + status = "okay";
> +
> + fusb0: fusb30x@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> + fcs,int_n = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&fusb0_int_gpio>;
> + status = "okay";
Remove or else status below.
New nodes are already okay I think.
If insure check compiled flat dts output to see if it is still there.
> + vbus-supply = <&vbus_typec>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + op-sink-microwatt = <1000000>;
> + power-role = "dual";
> + sink-pdos =
> + <PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
> + source-pdos =
> + <PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>;
> + try-power-role = "sink";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + usbc_hs: endpoint {
> + remote-endpoint =
> + <&u2phy0_typec_hs>;
> + };
> + };
> +
> + port@1 {
> + usbc_ss: endpoint {
> + remote-endpoint =
> + <&tcphy0_typec_ss>;
> + };
> + };
> +
> + port@2 {
> + usbc_dp: endpoint {
> + remote-endpoint =
> + <&tcphy0_typec_dp>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2s1 {
> + #sound-dai-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s_8ch_mclk_gpio>, <&i2s1_2ch_bus>;
> + rockchip,playback-channels = <8>;
> + rockchip,capture-channels = <8>;
sort
> + status = "okay";
> +};
> +
> +&io_domains {
> + audio-supply = <&vcc_3v0>;
> + gpio1830-supply = <&vcc_3v0>;
> + sdmmc-supply = <&vcc_sdio>;
> + status = "okay";
> +};
> +
> +&pcie_phy {
> + status = "okay";
> +};
> +
> +&pcie0 {
> + bus-scan-delay-ms = <1000>;
> + ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
> + max-link-speed = <2>;
> + num-lanes = <4>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_clkreqn_cpm>;
> + vpcie0v9-supply = <&vcca0v9_s3>;
> + vpcie1v8-supply = <&vcca1v8_s3>;
> + vpcie3v3-supply = <&vcc3v3_ssd>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + buttons {
> + pwrbtn_gpio: pwrbtn-gpio {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
Add extra empty line here.
> + lidbtn_gpio: lidbtn-gpio {
> + rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + dc-charger {
> + dc_det_gpio: dc-det-gpio {
> + rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + es8316 {
> + hp_det_gpio: hp-det-gpio {
> + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + fusb302x {
> + fusb0_int_gpio: fusb0-int-gpio {
> + rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + i2s1 {
> + i2s_8ch_mclk_gpio: i2s-8ch-mclk-gpio {
> + rockchip,pins = <4 RK_PA0 1 &pcfg_pull_none>;
> + };
> + };
> +
> + lcd-panel {
> + lcdvcc_en_gpio: lcdvcc-en-gpio {
> + rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + panel_en_gpio: panel-en-gpio {
> + rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + lcd_panel_reset_gpio: lcd-panel-reset-gpio {
> + rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + leds {
> + pwrled_gpio: pwrled_gpio {
> + rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + slpled_gpio: slpled_gpio {
> + rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l_gpio: pmic-int-l-gpio {
> + rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + vsel1_gpio: vsel1-gpio {
> + rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + vsel2_gpio: vsel2-gpio {
> + rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + sdcard {
> + sdmmc0_pwr_h_gpio: sdmmc0-pwr-h-gpio {
> + rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h_gpio: wifi-enable-h-gpio {
> + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb-typec {
> + vcc5v0_typec0_en_gpio: vcc5v0-typec0-en-gpio {
> + rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + usb2 {
> + pwr_5v_gpio: pwr-5v-gpio {
> + rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + vcc5v0_host_en_gpio: vcc5v0-host-en-gpio {
> + rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wireless-bluetooth {
> + bt_wake_gpio: bt-wake-gpio {
> + rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
Add extra empty line here.
> + bt_host_wake_gpio: bt-host-wake-gpio {
> + rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + bt_reset_gpio: bt-reset-gpio {
> + rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pmu_io_domains {
> + pmu1830-supply = <&vcc_3v0>;
> + status = "okay";
> +};
> +
> +&pwm0 {
> + status = "okay";
> +};
> +
> +&pwm2 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcca1v8_s3>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
> + sd-uhs-sdr104;
> + status = "okay";
> +};
> +
> +&sdio0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
> + sd-uhs-sdr104;
> + status = "okay";
> +};
> +
> +&sdhci {
> + bus-width = <8>;
> + mmc-hs200-1_8v;
> + non-removable;
> + status = "okay";
> +};
> +
> +&spi1 {
> + max-freq = <10000000>;
> + status = "okay";
> +
> + spiflash: flash@0 {
> + compatible = "jedec,spi-nor";
> + m25p,fast-read;
> + reg = <0>;
Change this to:
compatible = "jedec,spi-nor";
reg = <0>;
m25p,fast-read;
> + spi-max-frequency = <10000000>;
> + status = "okay";
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + loader@8000 {
> + label = "loader";
> + reg = <0x0 0x3F8000>;
> + };
> +
> + env@3f8000 {
> + label = "env";
> + reg = <0x3F8000 0x8000>;
> + };
> +
> + vendor@7c0000 {
> + label = "vendor";
> + reg = <0x7C0000 0x40000>;
> + };
> + };
Partitions are normaly up to the user and should not be included to dts
files,
else could you explain why we need this exception?
> + };
> +};
> +
> +&tcphy0 {
> + status = "okay";
> +};
> +
> +&tcphy0_dp {
> + port {
> + tcphy0_typec_dp: endpoint {
> + remote-endpoint = <&usbc_dp>;
> + };
> + };
> +};
> +
> +&tcphy0_usb3 {
> + port {
> + tcphy0_typec_ss: endpoint {
> + remote-endpoint = <&usbc_ss>;
> + };
> + };
> +};
> +
> +&tcphy1 {
> + status = "okay";
> +};
> +
> +&tsadc {
> + /* tshut mode 0:CRU 1:GPIO */
> + rockchip,hw-tshut-mode = <1>;
> + /* tshut polarity 0:LOW 1:HIGH */
> + rockchip,hw-tshut-polarity = <1>;
> + status = "okay";
> +};
> +
> +&u2phy0 {
> + status = "okay";
> +
> + u2phy0_otg: otg-port {
> + status = "okay";
> + };
> +
> + u2phy0_host: host-port {
> + phy-supply = <&vcc5v0_otg>;
> + status = "okay";
> + };
> +
> + port {
> + u2phy0_typec_hs: endpoint {
> + remote-endpoint = <&usbc_hs>;
> + };
> + };
> +};
> +
> +&u2phy1 {
> + status = "okay";
> +
> + u2phy1_otg: otg-port {
> + status = "okay";
> + };
> +
> + u2phy1_host: host-port {
> + phy-supply = <&vcc5v0_otg>;
> + status = "okay";
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
> + uart-has-rtscts;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "brcm,bcm4345c5";
> + clocks = <&rk808 1>;
> + clock-names = "lpo";
> + device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
> + host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
> + max-speed = <1500000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_host_wake_gpio &bt_wake_gpio &bt_reset_gpio>;
> + shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
> + vbat-supply = <&wifi_bat>;
> + vddio-supply = <&vcc_wl>;
> + };
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&usb_host1_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1_ohci {
> + status = "okay";
> +};
> +
> +&usbdrd3_0 {
> + status = "okay";
> +};
> +
> +&usbdrd_dwc3_0 {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbdrd3_1 {
> + status = "okay";
> +};
> +
> +&usbdrd_dwc3_1 {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> +};
> +
> +&vopl_mmu {
> + status = "okay";
> +};
>
Hi,
Add more reg = <..>
On 3/3/20 4:37 PM, Johan Jonker wrote:
> Hi Tobias,
>
> Some minor style issues.
> This dts file contains a partition node.
> Question for the maintainers (Heiko?):
> Should that partition be included or not?
[..]
>> +&i2c4 {
>> + i2c-scl-falling-time-ns = <20>;
>> + i2c-scl-rising-time-ns = <600>;
>> + status = "okay";
>> +
>> + fusb0: fusb30x@22 {
>> + compatible = "fcs,fusb302";
>> + reg = <0x22>;
>> + fcs,int_n = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&fusb0_int_gpio>;
>
>> + status = "okay";
>
> Remove or else status below.
> New nodes are already okay I think.
> If insure check compiled flat dts output to see if it is still there.
>
>> + vbus-supply = <&vbus_typec>;
>> +
>> + connector {
>> + compatible = "usb-c-connector";
>> + label = "USB-C";
>> + op-sink-microwatt = <1000000>;
>> + power-role = "dual";
>> + sink-pdos =
>> + <PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
>> + source-pdos =
>> + <PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>;
>> + try-power-role = "sink";
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
reg = <0>;
>> + usbc_hs: endpoint {
>> + remote-endpoint =
>> + <&u2phy0_typec_hs>;
>> + };
>> + };
>> +
>> + port@1 {
reg = <1>;
>> + usbc_ss: endpoint {
>> + remote-endpoint =
>> + <&tcphy0_typec_ss>;
>> + };
>> + };
>> +
>> + port@2 {
reg = <2>;
>> + usbc_dp: endpoint {
>> + remote-endpoint =
>> + <&tcphy0_typec_dp>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +};
Hi Johan,
thanks for the additional feedback. I'll send a v4 with your fixes included.
>> + partitions {
>> + compatible = "fixed-partitions";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + loader@8000 {
>> + label = "loader";
>> + reg = <0x0 0x3F8000>;
>> + };
>> +
>> + env@3f8000 {
>> + label = "env";
>> + reg = <0x3F8000 0x8000>;
>> + };
>> +
>> + vendor@7c0000 {
>> + label = "vendor";
>> + reg = <0x7C0000 0x40000>;
>> + };
>> + };
>
> Partitions are normaly up to the user and should not be included to dts
> files,
> else could you explain why we need this exception?
>
Right. I don't see any reason why we would need to keep it either. I'll
remove it.
Tobias