Hello.
Here's the set of 2 patches against DaveM's 'net-next.git' repo. They add to
the 'phylib' support for resetting devices via GPIO and do some clean up after
doing that...
[1/2] phylib: add device reset GPIO support
[2/2] macb: kill PHY reset code
MBR, Sergei
With the 'phylib' now being aware of the "reset-gpios" PHY node property,
there should be no need to frob the PHY reset in this driver anymore...
Signed-off-by: Sergei Shtylyov <[email protected]>
---
drivers/net/ethernet/cadence/macb.c | 17 -----------------
drivers/net/ethernet/cadence/macb.h | 1 -
2 files changed, 18 deletions(-)
Index: net-next/drivers/net/ethernet/cadence/macb.c
===================================================================
--- net-next.orig/drivers/net/ethernet/cadence/macb.c
+++ net-next/drivers/net/ethernet/cadence/macb.c
@@ -2884,7 +2884,6 @@ static int macb_probe(struct platform_de
= macb_clk_init;
int (*init)(struct platform_device *) = macb_init;
struct device_node *np = pdev->dev.of_node;
- struct device_node *phy_node;
const struct macb_config *macb_config = NULL;
struct clk *pclk, *hclk = NULL, *tx_clk = NULL;
unsigned int queue_mask, num_queues;
@@ -2977,18 +2976,6 @@ static int macb_probe(struct platform_de
else
macb_get_hwaddr(bp);
- /* Power up the PHY if there is a GPIO reset */
- phy_node = of_get_next_available_child(np, NULL);
- if (phy_node) {
- int gpio = of_get_named_gpio(phy_node, "reset-gpios", 0);
-
- if (gpio_is_valid(gpio)) {
- bp->reset_gpio = gpio_to_desc(gpio);
- gpiod_direction_output(bp->reset_gpio, 1);
- }
- }
- of_node_put(phy_node);
-
err = of_get_phy_mode(np);
if (err < 0) {
pdata = dev_get_platdata(&pdev->dev);
@@ -3054,10 +3041,6 @@ static int macb_remove(struct platform_d
mdiobus_unregister(bp->mii_bus);
mdiobus_free(bp->mii_bus);
- /* Shutdown the PHY if there is a GPIO reset */
- if (bp->reset_gpio)
- gpiod_set_value(bp->reset_gpio, 0);
-
unregister_netdev(dev);
clk_disable_unprepare(bp->tx_clk);
clk_disable_unprepare(bp->hclk);
Index: net-next/drivers/net/ethernet/cadence/macb.h
===================================================================
--- net-next.orig/drivers/net/ethernet/cadence/macb.h
+++ net-next/drivers/net/ethernet/cadence/macb.h
@@ -832,7 +832,6 @@ struct macb {
unsigned int dma_burst_length;
phy_interface_t phy_interface;
- struct gpio_desc *reset_gpio;
/* AT91RM9200 transmit */
struct sk_buff *skb; /* holds skb until xmit interrupt completes */
Le 29/04/2016 00:15, Sergei Shtylyov a ?crit :
> With the 'phylib' now being aware of the "reset-gpios" PHY node property,
> there should be no need to frob the PHY reset in this driver anymore...
>
> Signed-off-by: Sergei Shtylyov <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
So I queue my DT patch through arm-soc.
Thanks Sergei, bye.
> ---
> drivers/net/ethernet/cadence/macb.c | 17 -----------------
> drivers/net/ethernet/cadence/macb.h | 1 -
> 2 files changed, 18 deletions(-)
>
> Index: net-next/drivers/net/ethernet/cadence/macb.c
> ===================================================================
> --- net-next.orig/drivers/net/ethernet/cadence/macb.c
> +++ net-next/drivers/net/ethernet/cadence/macb.c
> @@ -2884,7 +2884,6 @@ static int macb_probe(struct platform_de
> = macb_clk_init;
> int (*init)(struct platform_device *) = macb_init;
> struct device_node *np = pdev->dev.of_node;
> - struct device_node *phy_node;
> const struct macb_config *macb_config = NULL;
> struct clk *pclk, *hclk = NULL, *tx_clk = NULL;
> unsigned int queue_mask, num_queues;
> @@ -2977,18 +2976,6 @@ static int macb_probe(struct platform_de
> else
> macb_get_hwaddr(bp);
>
> - /* Power up the PHY if there is a GPIO reset */
> - phy_node = of_get_next_available_child(np, NULL);
> - if (phy_node) {
> - int gpio = of_get_named_gpio(phy_node, "reset-gpios", 0);
> -
> - if (gpio_is_valid(gpio)) {
> - bp->reset_gpio = gpio_to_desc(gpio);
> - gpiod_direction_output(bp->reset_gpio, 1);
> - }
> - }
> - of_node_put(phy_node);
> -
> err = of_get_phy_mode(np);
> if (err < 0) {
> pdata = dev_get_platdata(&pdev->dev);
> @@ -3054,10 +3041,6 @@ static int macb_remove(struct platform_d
> mdiobus_unregister(bp->mii_bus);
> mdiobus_free(bp->mii_bus);
>
> - /* Shutdown the PHY if there is a GPIO reset */
> - if (bp->reset_gpio)
> - gpiod_set_value(bp->reset_gpio, 0);
> -
> unregister_netdev(dev);
> clk_disable_unprepare(bp->tx_clk);
> clk_disable_unprepare(bp->hclk);
> Index: net-next/drivers/net/ethernet/cadence/macb.h
> ===================================================================
> --- net-next.orig/drivers/net/ethernet/cadence/macb.h
> +++ net-next/drivers/net/ethernet/cadence/macb.h
> @@ -832,7 +832,6 @@ struct macb {
> unsigned int dma_burst_length;
>
> phy_interface_t phy_interface;
> - struct gpio_desc *reset_gpio;
>
> /* AT91RM9200 transmit */
> struct sk_buff *skb; /* holds skb until xmit interrupt completes */
>
>
--
Nicolas Ferre