Etron EJ168 USB 3.0 Host Controller stops working after S3, if it was
runtime suspended previously:
[ 370.080359] pci 0000:02:00.0: can't change power state from D3cold to D0 (config space inaccessible)
[ 370.080477] xhci_hcd 0000:04:00.0: can't change power state from D3cold to D0 (config space inaccessible)
[ 370.080532] pcieport 0000:00:1c.0: DPC: containment event, status:0x1f05 source:0x0200
[ 370.080533] pcieport 0000:00:1c.0: DPC: ERR_FATAL detected
[ 370.080536] xhci_hcd 0000:04:00.0: can't change power state from D3hot to D0 (config space inaccessible)
[ 370.080552] xhci_hcd 0000:04:00.0: AER: can't recover (no error_detected callback)
[ 370.080566] usb usb3: root hub lost power or was reset
[ 370.080566] usb usb4: root hub lost power or was reset
[ 370.080572] xhci_hcd 0000:04:00.0: Host halt failed, -19
[ 370.080574] xhci_hcd 0000:04:00.0: Host not accessible, reset failed.
[ 370.080575] xhci_hcd 0000:04:00.0: PCI post-resume error -19!
[ 370.080586] xhci_hcd 0000:04:00.0: HC died; cleaning up
This can be fixed by not runtime suspend the controller at all.
So disable runtime suspend for EJ168 xHCI device.
Signed-off-by: Kai-Heng Feng <[email protected]>
---
v3:
- Balance rpm refcount in remove callback.
v2:
- Use a new quirk to avoid changing existing behavior.
drivers/usb/host/xhci-pci.c | 7 ++++++-
drivers/usb/host/xhci.h | 1 +
2 files changed, 7 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index 766b74723e64..67b4b433a93e 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -227,6 +227,7 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
xhci->quirks |= XHCI_RESET_ON_RESUME;
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
xhci->quirks |= XHCI_BROKEN_STREAMS;
+ xhci->quirks |= XHCI_DISABLE_RUNTIME_SUSPEND;
}
if (pdev->vendor == PCI_VENDOR_ID_RENESAS &&
pdev->device == 0x0014) {
@@ -371,7 +372,8 @@ static int xhci_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
xhci->shared_hcd->can_do_streams = 1;
/* USB-2 and USB-3 roothubs initialized, allow runtime pm suspend */
- pm_runtime_put_noidle(&dev->dev);
+ if (!(xhci->quirks & XHCI_DISABLE_RUNTIME_SUSPEND))
+ pm_runtime_put_noidle(&dev->dev);
if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
pm_runtime_allow(&dev->dev);
@@ -397,6 +399,9 @@ static void xhci_pci_remove(struct pci_dev *dev)
if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
pm_runtime_forbid(&dev->dev);
+ if (!(xhci->quirks & XHCI_DISABLE_RUNTIME_SUSPEND))
+ pm_runtime_get_noresume(&dev->dev);
+
if (xhci->shared_hcd) {
usb_remove_hcd(xhci->shared_hcd);
usb_put_hcd(xhci->shared_hcd);
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 86cfefdd6632..d9c209a10d3f 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1873,6 +1873,7 @@ struct xhci_hcd {
#define XHCI_DEFAULT_PM_RUNTIME_ALLOW BIT_ULL(33)
#define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(34)
#define XHCI_SNPS_BROKEN_SUSPEND BIT_ULL(35)
+#define XHCI_DISABLE_RUNTIME_SUSPEND BIT_ULL(36)
unsigned int num_active_eps;
unsigned int limit_active_eps;
--
2.17.1
> On May 5, 2020, at 01:16, Kai-Heng Feng <[email protected]> wrote:
>
> Etron EJ168 USB 3.0 Host Controller stops working after S3, if it was
> runtime suspended previously:
> [ 370.080359] pci 0000:02:00.0: can't change power state from D3cold to D0 (config space inaccessible)
> [ 370.080477] xhci_hcd 0000:04:00.0: can't change power state from D3cold to D0 (config space inaccessible)
> [ 370.080532] pcieport 0000:00:1c.0: DPC: containment event, status:0x1f05 source:0x0200
> [ 370.080533] pcieport 0000:00:1c.0: DPC: ERR_FATAL detected
> [ 370.080536] xhci_hcd 0000:04:00.0: can't change power state from D3hot to D0 (config space inaccessible)
> [ 370.080552] xhci_hcd 0000:04:00.0: AER: can't recover (no error_detected callback)
> [ 370.080566] usb usb3: root hub lost power or was reset
> [ 370.080566] usb usb4: root hub lost power or was reset
> [ 370.080572] xhci_hcd 0000:04:00.0: Host halt failed, -19
> [ 370.080574] xhci_hcd 0000:04:00.0: Host not accessible, reset failed.
> [ 370.080575] xhci_hcd 0000:04:00.0: PCI post-resume error -19!
> [ 370.080586] xhci_hcd 0000:04:00.0: HC died; cleaning up
>
> This can be fixed by not runtime suspend the controller at all.
>
> So disable runtime suspend for EJ168 xHCI device.
>
> Signed-off-by: Kai-Heng Feng <[email protected]>
A gentle ping...
> ---
> v3:
> - Balance rpm refcount in remove callback.
>
> v2:
> - Use a new quirk to avoid changing existing behavior.
>
> drivers/usb/host/xhci-pci.c | 7 ++++++-
> drivers/usb/host/xhci.h | 1 +
> 2 files changed, 7 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
> index 766b74723e64..67b4b433a93e 100644
> --- a/drivers/usb/host/xhci-pci.c
> +++ b/drivers/usb/host/xhci-pci.c
> @@ -227,6 +227,7 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
> xhci->quirks |= XHCI_RESET_ON_RESUME;
> xhci->quirks |= XHCI_TRUST_TX_LENGTH;
> xhci->quirks |= XHCI_BROKEN_STREAMS;
> + xhci->quirks |= XHCI_DISABLE_RUNTIME_SUSPEND;
> }
> if (pdev->vendor == PCI_VENDOR_ID_RENESAS &&
> pdev->device == 0x0014) {
> @@ -371,7 +372,8 @@ static int xhci_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
> xhci->shared_hcd->can_do_streams = 1;
>
> /* USB-2 and USB-3 roothubs initialized, allow runtime pm suspend */
> - pm_runtime_put_noidle(&dev->dev);
> + if (!(xhci->quirks & XHCI_DISABLE_RUNTIME_SUSPEND))
> + pm_runtime_put_noidle(&dev->dev);
>
> if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
> pm_runtime_allow(&dev->dev);
> @@ -397,6 +399,9 @@ static void xhci_pci_remove(struct pci_dev *dev)
> if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
> pm_runtime_forbid(&dev->dev);
>
> + if (!(xhci->quirks & XHCI_DISABLE_RUNTIME_SUSPEND))
> + pm_runtime_get_noresume(&dev->dev);
> +
> if (xhci->shared_hcd) {
> usb_remove_hcd(xhci->shared_hcd);
> usb_put_hcd(xhci->shared_hcd);
> diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
> index 86cfefdd6632..d9c209a10d3f 100644
> --- a/drivers/usb/host/xhci.h
> +++ b/drivers/usb/host/xhci.h
> @@ -1873,6 +1873,7 @@ struct xhci_hcd {
> #define XHCI_DEFAULT_PM_RUNTIME_ALLOW BIT_ULL(33)
> #define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(34)
> #define XHCI_SNPS_BROKEN_SUSPEND BIT_ULL(35)
> +#define XHCI_DISABLE_RUNTIME_SUSPEND BIT_ULL(36)
>
> unsigned int num_active_eps;
> unsigned int limit_active_eps;
> --
> 2.17.1
>
> On Jun 8, 2020, at 11:56, Kai-Heng Feng <[email protected]> wrote:
>
>
>
>> On May 5, 2020, at 01:16, Kai-Heng Feng <[email protected]> wrote:
>>
>> Etron EJ168 USB 3.0 Host Controller stops working after S3, if it was
>> runtime suspended previously:
>> [ 370.080359] pci 0000:02:00.0: can't change power state from D3cold to D0 (config space inaccessible)
>> [ 370.080477] xhci_hcd 0000:04:00.0: can't change power state from D3cold to D0 (config space inaccessible)
>> [ 370.080532] pcieport 0000:00:1c.0: DPC: containment event, status:0x1f05 source:0x0200
>> [ 370.080533] pcieport 0000:00:1c.0: DPC: ERR_FATAL detected
>> [ 370.080536] xhci_hcd 0000:04:00.0: can't change power state from D3hot to D0 (config space inaccessible)
>> [ 370.080552] xhci_hcd 0000:04:00.0: AER: can't recover (no error_detected callback)
>> [ 370.080566] usb usb3: root hub lost power or was reset
>> [ 370.080566] usb usb4: root hub lost power or was reset
>> [ 370.080572] xhci_hcd 0000:04:00.0: Host halt failed, -19
>> [ 370.080574] xhci_hcd 0000:04:00.0: Host not accessible, reset failed.
>> [ 370.080575] xhci_hcd 0000:04:00.0: PCI post-resume error -19!
>> [ 370.080586] xhci_hcd 0000:04:00.0: HC died; cleaning up
>>
>> This can be fixed by not runtime suspend the controller at all.
>>
>> So disable runtime suspend for EJ168 xHCI device.
>>
>> Signed-off-by: Kai-Heng Feng <[email protected]>
>
> A gentle ping...
Another gentle ping...
>
>> ---
>> v3:
>> - Balance rpm refcount in remove callback.
>>
>> v2:
>> - Use a new quirk to avoid changing existing behavior.
>>
>> drivers/usb/host/xhci-pci.c | 7 ++++++-
>> drivers/usb/host/xhci.h | 1 +
>> 2 files changed, 7 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
>> index 766b74723e64..67b4b433a93e 100644
>> --- a/drivers/usb/host/xhci-pci.c
>> +++ b/drivers/usb/host/xhci-pci.c
>> @@ -227,6 +227,7 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
>> xhci->quirks |= XHCI_RESET_ON_RESUME;
>> xhci->quirks |= XHCI_TRUST_TX_LENGTH;
>> xhci->quirks |= XHCI_BROKEN_STREAMS;
>> + xhci->quirks |= XHCI_DISABLE_RUNTIME_SUSPEND;
>> }
>> if (pdev->vendor == PCI_VENDOR_ID_RENESAS &&
>> pdev->device == 0x0014) {
>> @@ -371,7 +372,8 @@ static int xhci_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
>> xhci->shared_hcd->can_do_streams = 1;
>>
>> /* USB-2 and USB-3 roothubs initialized, allow runtime pm suspend */
>> - pm_runtime_put_noidle(&dev->dev);
>> + if (!(xhci->quirks & XHCI_DISABLE_RUNTIME_SUSPEND))
>> + pm_runtime_put_noidle(&dev->dev);
>>
>> if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
>> pm_runtime_allow(&dev->dev);
>> @@ -397,6 +399,9 @@ static void xhci_pci_remove(struct pci_dev *dev)
>> if (xhci->quirks & XHCI_DEFAULT_PM_RUNTIME_ALLOW)
>> pm_runtime_forbid(&dev->dev);
>>
>> + if (!(xhci->quirks & XHCI_DISABLE_RUNTIME_SUSPEND))
>> + pm_runtime_get_noresume(&dev->dev);
>> +
>> if (xhci->shared_hcd) {
>> usb_remove_hcd(xhci->shared_hcd);
>> usb_put_hcd(xhci->shared_hcd);
>> diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
>> index 86cfefdd6632..d9c209a10d3f 100644
>> --- a/drivers/usb/host/xhci.h
>> +++ b/drivers/usb/host/xhci.h
>> @@ -1873,6 +1873,7 @@ struct xhci_hcd {
>> #define XHCI_DEFAULT_PM_RUNTIME_ALLOW BIT_ULL(33)
>> #define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(34)
>> #define XHCI_SNPS_BROKEN_SUSPEND BIT_ULL(35)
>> +#define XHCI_DISABLE_RUNTIME_SUSPEND BIT_ULL(36)
>>
>> unsigned int num_active_eps;
>> unsigned int limit_active_eps;
>> --
>> 2.17.1
>>
>
On 28.9.2020 12.10, Kai-Heng Feng wrote:
>
>
>> On Jun 8, 2020, at 11:56, Kai-Heng Feng <[email protected]> wrote:
>>
>>
>>
>>> On May 5, 2020, at 01:16, Kai-Heng Feng <[email protected]> wrote:
>>>
>>> Etron EJ168 USB 3.0 Host Controller stops working after S3, if it was
>>> runtime suspended previously:
>>> [ 370.080359] pci 0000:02:00.0: can't change power state from D3cold to D0 (config space inaccessible)
>>> [ 370.080477] xhci_hcd 0000:04:00.0: can't change power state from D3cold to D0 (config space inaccessible)
>>> [ 370.080532] pcieport 0000:00:1c.0: DPC: containment event, status:0x1f05 source:0x0200
>>> [ 370.080533] pcieport 0000:00:1c.0: DPC: ERR_FATAL detected
>>> [ 370.080536] xhci_hcd 0000:04:00.0: can't change power state from D3hot to D0 (config space inaccessible)
>>> [ 370.080552] xhci_hcd 0000:04:00.0: AER: can't recover (no error_detected callback)
>>> [ 370.080566] usb usb3: root hub lost power or was reset
>>> [ 370.080566] usb usb4: root hub lost power or was reset
>>> [ 370.080572] xhci_hcd 0000:04:00.0: Host halt failed, -19
>>> [ 370.080574] xhci_hcd 0000:04:00.0: Host not accessible, reset failed.
>>> [ 370.080575] xhci_hcd 0000:04:00.0: PCI post-resume error -19!
>>> [ 370.080586] xhci_hcd 0000:04:00.0: HC died; cleaning up
>>>
>>> This can be fixed by not runtime suspend the controller at all.
>>>
>>> So disable runtime suspend for EJ168 xHCI device.
>>>
>>> Signed-off-by: Kai-Heng Feng <[email protected]>
>>
>> A gentle ping...
>
> Another gentle ping...
Thanks, somehow I didn't notice this earlier.
Was the rootcause ever investigated?
Preventing runtime suspend looks like a quick fix to get rid of the issue, but
possibly just hides some other underlying power management problem
-Mathias
> On Sep 29, 2020, at 05:42, Mathias Nyman <[email protected]> wrote:
>
> On 28.9.2020 12.10, Kai-Heng Feng wrote:
>>
>>
>>> On Jun 8, 2020, at 11:56, Kai-Heng Feng <[email protected]> wrote:
>>>
>>>
>>>
>>>> On May 5, 2020, at 01:16, Kai-Heng Feng <[email protected]> wrote:
>>>>
>>>> Etron EJ168 USB 3.0 Host Controller stops working after S3, if it was
>>>> runtime suspended previously:
>>>> [ 370.080359] pci 0000:02:00.0: can't change power state from D3cold to D0 (config space inaccessible)
>>>> [ 370.080477] xhci_hcd 0000:04:00.0: can't change power state from D3cold to D0 (config space inaccessible)
>>>> [ 370.080532] pcieport 0000:00:1c.0: DPC: containment event, status:0x1f05 source:0x0200
>>>> [ 370.080533] pcieport 0000:00:1c.0: DPC: ERR_FATAL detected
>>>> [ 370.080536] xhci_hcd 0000:04:00.0: can't change power state from D3hot to D0 (config space inaccessible)
>>>> [ 370.080552] xhci_hcd 0000:04:00.0: AER: can't recover (no error_detected callback)
>>>> [ 370.080566] usb usb3: root hub lost power or was reset
>>>> [ 370.080566] usb usb4: root hub lost power or was reset
>>>> [ 370.080572] xhci_hcd 0000:04:00.0: Host halt failed, -19
>>>> [ 370.080574] xhci_hcd 0000:04:00.0: Host not accessible, reset failed.
>>>> [ 370.080575] xhci_hcd 0000:04:00.0: PCI post-resume error -19!
>>>> [ 370.080586] xhci_hcd 0000:04:00.0: HC died; cleaning up
>>>>
>>>> This can be fixed by not runtime suspend the controller at all.
>>>>
>>>> So disable runtime suspend for EJ168 xHCI device.
>>>>
>>>> Signed-off-by: Kai-Heng Feng <[email protected]>
>>>
>>> A gentle ping...
>>
>> Another gentle ping...
>
> Thanks, somehow I didn't notice this earlier.
>
> Was the rootcause ever investigated?
> Preventing runtime suspend looks like a quick fix to get rid of the issue, but
> possibly just hides some other underlying power management problem
I tried different angles but didn't find any useful solution.
Eventually I found out that the device stays at D0 under Windows, so this is the approach I take.
Kai-Heng
>
> -Mathias