The otg sync state patch reuses the ret variable, but fails to set it to
zero after use. This leads to a situation when the otg port is in
peripheral mode where the otg phy aborts halfway through setup. It also
fails to account for a failure to register the extcon notifier. Fix this
by using our own variable and skipping otg sync in case of failure.
Fixes: 8dc60f8da22f ("phy: rockchip-inno-usb2: Sync initial otg state")
Reported-by: Markus Reichl <[email protected]>
Reported-by: Michael Riesch <[email protected]>
Signed-off-by: Peter Geis <[email protected]>
Tested-by: Michael Riesch <[email protected]>
Tested-by: Markus Reichl <[email protected]>
---
Changelog:
v4
- fix a checkpatch style error (thanks Vinod)
v3
- add missing brackets around new goto
v2
- switch to using our own variable
- add missing goto to skip sync in case of registration failure
---
drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
index 0b1e9337ee8e..e6ededc51523 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
@@ -1124,7 +1124,7 @@ static int rockchip_usb2phy_otg_port_init(struct rockchip_usb2phy *rphy,
struct rockchip_usb2phy_port *rport,
struct device_node *child_np)
{
- int ret;
+ int ret, id;
rport->port_id = USB2PHY_PORT_OTG;
rport->port_cfg = &rphy->phy_cfg->port_cfgs[USB2PHY_PORT_OTG];
@@ -1162,13 +1162,15 @@ static int rockchip_usb2phy_otg_port_init(struct rockchip_usb2phy *rphy,
ret = devm_extcon_register_notifier(rphy->dev, rphy->edev,
EXTCON_USB_HOST, &rport->event_nb);
- if (ret)
+ if (ret) {
dev_err(rphy->dev, "register USB HOST notifier failed\n");
+ goto out;
+ }
if (!of_property_read_bool(rphy->dev->of_node, "extcon")) {
/* do initial sync of usb state */
- ret = property_enabled(rphy->grf, &rport->port_cfg->utmi_id);
- extcon_set_state_sync(rphy->edev, EXTCON_USB_HOST, !ret);
+ id = property_enabled(rphy->grf, &rport->port_cfg->utmi_id);
+ extcon_set_state_sync(rphy->edev, EXTCON_USB_HOST, !id);
}
}
--
2.25.1
On 9/2/22 1:45 PM, Peter Geis wrote:
> The otg sync state patch reuses the ret variable, but fails to set it to
> zero after use. This leads to a situation when the otg port is in
> peripheral mode where the otg phy aborts halfway through setup. It also
> fails to account for a failure to register the extcon notifier. Fix this
> by using our own variable and skipping otg sync in case of failure.
>
> Fixes: 8dc60f8da22f ("phy: rockchip-inno-usb2: Sync initial otg state")
> Reported-by: Markus Reichl <[email protected]>
> Reported-by: Michael Riesch <[email protected]>
> Signed-off-by: Peter Geis <[email protected]>
> Tested-by: Michael Riesch <[email protected]>
> Tested-by: Markus Reichl <[email protected]>
Reviewed-by: Samuel Holland <[email protected]>
On 02-09-22, 14:45, Peter Geis wrote:
> The otg sync state patch reuses the ret variable, but fails to set it to
> zero after use. This leads to a situation when the otg port is in
> peripheral mode where the otg phy aborts halfway through setup. It also
> fails to account for a failure to register the extcon notifier. Fix this
> by using our own variable and skipping otg sync in case of failure.
Applied, thanks
--
~Vinod
On Sun, Sep 4, 2022 at 11:24 PM Vinod Koul <[email protected]> wrote:
>
> On 02-09-22, 14:45, Peter Geis wrote:
> > The otg sync state patch reuses the ret variable, but fails to set it to
> > zero after use. This leads to a situation when the otg port is in
> > peripheral mode where the otg phy aborts halfway through setup. It also
> > fails to account for a failure to register the extcon notifier. Fix this
> > by using our own variable and skipping otg sync in case of failure.
>
> Applied, thanks
This should have been applied for v6.0-rc, not -next.
We now have a v6.0 release that doesn't boot properly on RK3399.
ChenYu