This patch series add support for Xiaomi Mi 11 Ultra.
Signed-off-by: Xilin Wu <[email protected]>
---
Changes in v2:
- Modified framebuffer node name
- Removed trailing blank line
- Ensured all status property be the last one
- Added UFS host controller supply
- Link to v1: https://lore.kernel.org/r/all/[email protected]
---
---
Xilin Wu (3):
soc: qcom: pmic_glink: enable UCSI for SM8350
dt-bindings: arm: qcom: Add Xiaomi Mi 11 Ultra
arm64: dts: qcom: Add device tree for Xiaomi Mi 11 Ultra
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8350-xiaomi-star.dts | 1249 +++++++++++++++++++++++
drivers/soc/qcom/pmic_glink.c | 1 +
4 files changed, 1252 insertions(+)
---
base-commit: 2dac75696c6da3c848daa118a729827541c89d33
change-id: 20231021-sakuramist-mi11u-b9e99e27c04c
Best regards,
--
Xilin Wu <[email protected]>
From: Xilin Wu <[email protected]>
UCSI is supported on SM8350. Allow it to enable USB role switch and
altmode notifications on SM8350.
Signed-off-by: Xilin Wu <[email protected]>
---
drivers/soc/qcom/pmic_glink.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
index 914057331afd..1196e79e6fb3 100644
--- a/drivers/soc/qcom/pmic_glink.c
+++ b/drivers/soc/qcom/pmic_glink.c
@@ -341,6 +341,7 @@ static const unsigned long pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT
BIT(PMIC_GLINK_CLIENT_UCSI);
static const struct of_device_id pmic_glink_of_match[] = {
+ { .compatible = "qcom,sm8350-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
{ .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
{ .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
{ .compatible = "qcom,pmic-glink" },
--
2.42.0
From: Xilin Wu <[email protected]>
Add support for Xiaomi Mi 11 Ultra. This commit brings support for:
* Front and rear display panels (initialized by bootloader)
* USB
* UFS
* PCIe0
* Thermistor sensors
* ADSP/CDSP/Modem/SLPI
* IR Transmitter
* RTC provided by PMK8350
* Buttons
To create a working boot image, you need to run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/sm8350-xiaomi-\
star.dtb > .Image.gz-dtb
mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd.img \
--pagesize 4096 \
--base 0x0 \
--kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 \
--tags_offset 0x100 \
--cmdline "SOME_CMDLINE" \
--dtb_offset 0x1f00000 \
--header_version 1 \
--os_version 14.0.0 \
--os_patch_level 2099-12 \
-o boot.img-xiaomi-star
Then, you can flash it to slot b on the device:
// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
fastboot --disable-verity --disable-verification flash vbmeta_b vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system_b \
vbmeta_system.img
fastboot flash boot_b boot.img-xiaomi-star
fastboot erase dtbo_b
fastboot set_active b
fastboot reboot
Signed-off-by: Xilin Wu <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/sm8350-xiaomi-star.dts | 1249 +++++++++++++++++++++++
2 files changed, 1250 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index d6cb840b7050..635bda47ebdf 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -225,6 +225,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8350-microsoft-surface-duo2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8350-sony-xperia-sagami-pdx214.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8350-sony-xperia-sagami-pdx215.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8350-xiaomi-star.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8450-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8450-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8450-sony-xperia-nagara-pdx223.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8350-xiaomi-star.dts b/arch/arm64/boot/dts/qcom/sm8350-xiaomi-star.dts
new file mode 100644
index 000000000000..6140e74fd2e9
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8350-xiaomi-star.dts
@@ -0,0 +1,1249 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Xilin Wu <[email protected]>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pm8350b.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
+#include "sm8350.dtsi"
+#include "pm8350.dtsi"
+#include "pm8350b.dtsi"
+#include "pm8350c.dtsi"
+#include "pmk8350.dtsi"
+#include "pmr735a.dtsi"
+
+/*
+ * Delete following upstream (sm8350.dtsi) reserved
+ * memory mappings which are different on this device.
+ */
+/delete-node/ &pil_adsp_mem;
+/delete-node/ &pil_slpi_mem;
+/delete-node/ &pil_cdsp_mem;
+/delete-node/ &pil_ipa_fw_mem;
+/delete-node/ &pil_ipa_gsi_mem;
+/delete-node/ &pil_gpu_mem;
+/delete-node/ &pil_spss_mem;
+/delete-node/ &pil_modem_mem;
+/delete-node/ &rmtfs_mem;
+/delete-node/ &pil_trustedvm_mem;
+/delete-node/ &removed_mem;
+
+/ {
+ model = "Xiaomi Mi 11 Ultra";
+ compatible = "xiaomi,star", "qcom,sm8350";
+ chassis-type = "handset";
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer0: framebuffer@ea600000 {
+ compatible = "simple-framebuffer";
+ reg = <0 0xea600000 0 (1440 * 3200 * 4)>;
+
+ width = <1440>;
+ height = <3200>;
+ stride = <(1440 * 4)>;
+ format = "a8r8g8b8";
+ };
+
+ framebuffer1: framebuffer@eb79c000 {
+ compatible = "simple-framebuffer";
+ reg = <0 0xeb79c000 0 (126 * 294 * 4)>;
+
+ width = <126>;
+ height = <294>;
+ stride = <(126 * 4)>;
+ format = "a8r8g8b8";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&volume_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8350_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu: endpoint {
+ remote-endpoint = <&fsa4480_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ reserved-memory {
+ pil_adsp_mem: memory@86100000 {
+ reg = <0 0x86100000 0 0x3900000>;
+ no-map;
+ };
+
+ pil_slpi_mem: memory@89a00000 {
+ reg = <0 0x89a00000 0 0x2f00000>;
+ no-map;
+ };
+
+ pil_cdsp_mem: memory@8c900000 {
+ reg = <0 0x8c900000 0 0x1e00000>;
+ no-map;
+ };
+
+ pil_ipa_fw_mem: memory@8e700000 {
+ reg = <0 0x8e700000 0 0x10000>;
+ no-map;
+ };
+
+ pil_ipa_gsi_mem: memory@8e710000 {
+ reg = <0 0x8e710000 0 0xa000>;
+ no-map;
+ };
+
+ pil_gpu_mem: memory@8e71a000 {
+ reg = <0 0x8e71a000 0 0x2000>;
+ no-map;
+ };
+
+ pil_spss_mem: memory@8e800000 {
+ reg = <0 0x8e800000 0 0x100000>;
+ no-map;
+ };
+
+ pil_modem_mem: memory@8f000000 {
+ reg = <0 0x8f000000 0 0x10000000>;
+ no-map;
+ };
+
+ ramoops@b0000000 {
+ compatible = "ramoops";
+ reg = <0 0xb0000000 0 0x400000>;
+ console-size = <0x200000>;
+ pmsg-size = <0x200000>;
+ ecc-size = <16>;
+ no-map;
+ };
+
+ rmtfs_mem: memory@d6a00000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0 0xd6a00000 0 0x300000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ qcom,vmid = <15>;
+ };
+
+ removed_mem: memory@d8800000 {
+ reg = <0 0xd8800000 0 0xa000000>;
+ no-map;
+ };
+
+ cont_splash_mem: memory@ea600000 {
+ reg = <0 0xea600000 0 0x2400000>;
+ no-map;
+ };
+ };
+
+ thermal-zones {
+ skin-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pmk8350_adc_tm 0>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ flash-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pmk8350_adc_tm 1>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ usb-con-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pmk8350_adc_tm 2>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ quiet-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pmk8350_adc_tm 3>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ pa-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pmk8350_adc_tm 4>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wl-chg-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pmk8350_adc_tm 5>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wifi-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&pmk8350_adc_tm 6>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&adsp {
+ firmware-name = "qcom/sm8350/xiaomi/star/adsp.mbn";
+ status = "okay";
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8350-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-s11-supply = <&vph_pwr>;
+ vdd-s12-supply = <&vph_pwr>;
+
+ vdd-l1-l4-supply = <&vreg_s11b_0p95>;
+ vdd-l2-l7-supply = <&vreg_bob>;
+ vdd-l3-l5-supply = <&vreg_bob>;
+ vdd-l6-l9-l10-supply = <&vreg_s11b_0p95>;
+ vdd-l8-supply = <&vreg_s2c_0p8>;
+
+ vreg_s10b_1p8: smps10 {
+ regulator-name = "vreg_s10b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_s11b_0p95: smps11 {
+ regulator-name = "vreg_s11b_0p95";
+ regulator-min-microvolt = <752000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ vreg_s12b_1p25: smps12 {
+ regulator-name = "vreg_s12b_1p25";
+ regulator-min-microvolt = <1224000>;
+ regulator-max-microvolt = <1360000>;
+ };
+
+ vreg_l1b_0p88: ldo1 {
+ regulator-name = "vreg_l1b_0p88";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p07: ldo2 {
+ regulator-name = "vreg_l2b_3p07";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3b_0p9: ldo3 {
+ regulator-name = "vreg_l3b_0p9";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_0p88: ldo5 {
+ regulator-name = "vreg_l5b_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <888000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p2: ldo6 {
+ regulator-name = "vreg_l6b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1208000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_2p96: ldo7 {
+ regulator-name = "vreg_l7b_2p96";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_1p2: ldo9 {
+ regulator-name = "vreg_l9b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8350c-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+
+ vdd-l1-l12-supply = <&vreg_s1c_1p86>;
+ vdd-l2-l8-supply = <&vreg_s1c_1p86>;
+ vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
+ vdd-l6-l9-l11-supply = <&vreg_bob>;
+ vdd-l10-supply = <&vreg_s12b_1p25>;
+
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_s1c_1p86: smps1 {
+ regulator-name = "vreg_s1c_1p86";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ };
+
+ vreg_s2c_0p8: smps2 {
+ regulator-name = "vreg_s2c_0p8";
+ regulator-min-microvolt = <640000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ vreg_s10c_1p05: smps10 {
+ regulator-name = "vreg_s10c_1p05";
+ regulator-min-microvolt = <1048000>;
+ regulator-max-microvolt = <1128000>;
+ };
+
+ vreg_bob: bob {
+ regulator-name = "vreg_bob";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ };
+
+ vreg_l1c_1p8: ldo1 {
+ regulator-name = "vreg_l1c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c_1p8: ldo2 {
+ regulator-name = "vreg_l2c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_3p0: ldo3 {
+ regulator-name = "vreg_l3c_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c_uim1: ldo4 {
+ regulator-name = "vreg_l4c_uim1";
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5c_uim2: ldo5 {
+ regulator-name = "vreg_l5c_uim2";
+ regulator-min-microvolt = <1704000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c_1p8: ldo6 {
+ regulator-name = "vreg_l6c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c_3p0: ldo7 {
+ regulator-name = "vreg_l7c_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c_1p8: ldo8 {
+ regulator-name = "vreg_l8c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c_2p96: ldo9 {
+ regulator-name = "vreg_l9c_2p96";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10c_1p2: ldo10 {
+ regulator-name = "vreg_l10c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11c_2p96: ldo11 {
+ regulator-name = "vreg_l11c_2p96";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12c_1p8: ldo12 {
+ regulator-name = "vreg_l12c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13c_3p0: ldo13 {
+ regulator-name = "vreg_l13c_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pmr735a-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+
+ vdd-l1-l2-supply = <&pmr735a_s2>;
+ vdd-l3-supply = <&pmr735a_s1>;
+ vdd-l4-supply = <&vreg_s1c_1p86>;
+ vdd-l5-l6-supply = <&vreg_s1c_1p86>;
+ vdd-l7-bob-supply = <&vreg_bob>;
+
+ pmr735a_s1: smps1 {
+ regulator-name = "pmr735a_s1";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1280000>;
+ };
+
+ pmr735a_s2: smps2 {
+ regulator-name = "pmr735a_s2";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <976000>;
+ };
+
+ pmr735a_s3: smps3 {
+ regulator-name = "pmr735a_s3";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2352000>;
+ };
+
+ pmr735a_l1: ldo1 {
+ regulator-name = "pmr735a_l1";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ };
+
+ pmr735a_l2: ldo2 {
+ regulator-name = "pmr735a_l2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pmr735a_l3: ldo3 {
+ regulator-name = "pmr735a_l3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pmr735a_l4: ldo4 {
+ regulator-name = "pmr735a_l4";
+ regulator-min-microvolt = <1776000>;
+ regulator-max-microvolt = <1872000>;
+ };
+
+ pmr735a_l5: ldo5 {
+ regulator-name = "pmr735a_l5";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ pmr735a_l6: ldo6 {
+ regulator-name = "pmr735a_l6";
+ regulator-min-microvolt = <480000>;
+ regulator-max-microvolt = <904000>;
+ };
+
+ pmr735a_l7: ldo7 {
+ regulator-name = "pmr735a_l7";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+ };
+};
+
+&cdsp {
+ firmware-name = "qcom/sm8350/xiaomi/star/cdsp.mbn";
+ status = "okay";
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&gpi_dma2 {
+ status = "okay";
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ /* Zinitix BT541 or Cypress CYTTSP5 rear touchscreen @ 24 */
+};
+
+&i2c6 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ /* AWINIC AW8697 vibrator @ 5a */
+};
+
+&i2c8 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ cs35l41_l: speaker-amp@40 {
+ compatible = "cirrus,cs35l41";
+ reg = <0x40>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <44 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&tlmm 15 GPIO_ACTIVE_HIGH>;
+ VA-supply = <&vreg_s10b_1p8>;
+ VP-supply = <&vph_pwr>;
+ cirrus,boost-peak-milliamp = <4000>;
+ cirrus,boost-ind-nanohenry = <1000>;
+ cirrus,boost-cap-microfarad = <15>;
+ cirrus,gpio2-src-select = <2>;
+ cirrus,gpio2-output-enable;
+ cirrus,asp-sdout-hiz = <3>;
+ #sound-dai-cells = <1>;
+ };
+
+ cs35l41_r: speaker-amp@42 {
+ compatible = "cirrus,cs35l41";
+ reg = <0x42>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <116 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&tlmm 15 GPIO_ACTIVE_HIGH>;
+ VA-supply = <&vreg_s10b_1p8>;
+ VP-supply = <&vph_pwr>;
+ cirrus,boost-peak-milliamp = <4000>;
+ cirrus,boost-ind-nanohenry = <1000>;
+ cirrus,boost-cap-microfarad = <15>;
+ cirrus,gpio2-src-select = <2>;
+ cirrus,gpio2-output-enable;
+ cirrus,asp-sdout-hiz = <3>;
+ #sound-dai-cells = <1>;
+ };
+};
+
+&i2c13 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ typec-mux@42 {
+ compatible = "fcs,fsa4480";
+ reg = <0x42>;
+
+ interrupts-extended = <&tlmm 2 IRQ_TYPE_LEVEL_LOW>;
+
+ vcc-supply = <&vreg_bob>;
+ mode-switch;
+ orientation-switch;
+
+ port {
+ fsa4480_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_sbu>;
+ };
+ };
+ };
+};
+
+&i2c15 {
+ clock-frequency = <1000000>;
+ status = "okay";
+};
+
+&ipa {
+ qcom,gsi-loader = "self";
+ memory-region = <&pil_ipa_fw_mem>;
+ firmware-name = "qcom/sm8350/xiaomi/star/ipa_fws.mbn";
+ status = "okay";
+};
+
+&mpss {
+ firmware-name = "qcom/sm8350/xiaomi/star/modem.mbn";
+ status = "okay";
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_default_state>;
+
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l5b_0p88>;
+ vdda-pll-supply = <&vreg_l6b_1p2>;
+
+ status = "okay";
+};
+
+&pm8350_gpios {
+ gpio-line-names = "NC",
+ "BuildID",
+ "NC",
+ "ProjectID",
+ "NC",
+ "KEY_VOLP_N",
+ "SP_ARI_POWER_ALARM",
+ "NC",
+ "NC",
+ "GND";
+
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
+&pm8350b_gpios {
+ gpio-line-names = "WIFI_THERM",
+ "WP_THERM",
+ "NC",
+ "NC",
+ "NC",
+ "FORCED_USB_BOOT",
+ "NC",
+ "NC";
+};
+
+&pm8350c_gpios {
+ gpio-line-names = "VDD_BOOST_5V_EN",
+ "NC",
+ "OTG_OVP_EN",
+ "WL_TXON",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC";
+};
+
+&pmk8350_adc_tm {
+ status = "okay";
+
+ pm8350-skin-therm@0 {
+ reg = <0>;
+ io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ pm8350-cam-flash-therm@1 {
+ reg = <1>;
+ io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ pm8350b-usb-con-therm@2 {
+ reg = <2>;
+ io-channels = <&pmk8350_vadc PM8350B_ADC7_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ pm8350-quiet-therm@3 {
+ reg = <3>;
+ io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ pmr735a-pa-therm@4 {
+ reg = <4>;
+ io-channels = <&pmk8350_vadc PMR735A_ADC7_GPIO1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ pm8350b-wl-chg-therm@5 {
+ reg = <5>;
+ io-channels = <&pmk8350_vadc PM8350B_ADC7_GPIO2_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+
+ pm8350b-wifi-therm@6 {
+ reg = <6>;
+ io-channels = <&pmk8350_vadc PM8350B_ADC7_GPIO1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time-us = <200>;
+ };
+};
+
+&pmk8350_rtc {
+ nvmem-cells = <&rtc_offset>;
+ nvmem-cell-names = "offset";
+
+ status = "okay";
+};
+
+&pmk8350_sdam_2 {
+ status = "okay";
+
+ rtc_offset: rtc-offset@bc {
+ reg = <0xbc 0x4>;
+ };
+};
+
+&pmk8350_vadc {
+ channel@324 {
+ reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pm8350_skin_therm";
+ };
+
+ channel@325 {
+ reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pm8350_cam_flash_therm";
+ };
+
+ channel@327 {
+ reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pm8350_quiet_therm";
+ };
+
+ channel@836 {
+ reg = <PM8350B_ADC7_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pm8350b_usb_con_therm";
+ };
+
+ channel@842 {
+ reg = <PM8350B_ADC7_GPIO1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pm8350b_wifi_therm";
+ };
+
+ channel@843 {
+ reg = <PM8350B_ADC7_GPIO2_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pm8350b_wl_chg_therm";
+ };
+
+ channel@1098 {
+ reg = <PMR735A_ADC7_GPIO1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pmr735a_pa_therm";
+ };
+};
+
+&pmr735a_gpios {
+ gpio-line-names = "PA_THERM0",
+ "PA_THERM1",
+ "NC",
+ "NC";
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qupv3_id_2 {
+ status = "okay";
+};
+
+&slpi {
+ firmware-name = "qcom/sm8350/xiaomi/star/slpi.mbn";
+ status = "okay";
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi1_default>;
+ status = "okay";
+
+ irled@0 {
+ compatible = "ir-spi-led";
+ reg = <0>;
+ power-supply = <&vph_pwr>;
+ spi-max-frequency = <19200000>;
+ };
+};
+
+&spi11 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi11_default>;
+ status = "okay";
+
+ /* STM FTS touchscreen */
+};
+
+&tlmm {
+ gpio-reserved-ranges = <52 8>;
+ gpio-line-names = "APPS_I2C_SDA", /* GPIO_0 */
+ "APPS_I2C_SCL",
+ "FSA_INT_N",
+ "SEC_AMOLED_CVO_EN",
+ "WLC_PMIC_I2C_SDA",
+ "WLC_PMIC_I2C_SCL",
+ "SBU_UART_EN",
+ "WLC_INT_N",
+ "NC",
+ "INFARED_SPI_MOSI",
+ "NC", /* GPIO_10 */
+ "NC",
+ "CAMW_AVDD_EN",
+ "AMOLED_VDDI_EN",
+ "CP_INT",
+ "SMART_PA_0_EN",
+ "CAM1_RESET_N",
+ "CAM5_RESET_N",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "TS_I2C_SDA", /* GPIO_20 */
+ "TS_I2C_SCL",
+ "TP_RESET_N",
+ "TP_INT_N",
+ "LCD_RESET_N",
+ "WL_CP_EN_AP",
+ "WL_DET",
+ "CP_INT_S",
+ "HAP_I2C_SDA",
+ "HAP_I2C_SCL",
+ "SEC_AMOLED_RESET_DIS", /* GPIO_30 */
+ "SEC_AMOLED_TP_INT",
+ "PM8008_1_IRQ",
+ "PM8008_1_RESET_N",
+ "CAMFD_AVDD_EN",
+ "SEC_AMOLED_VDDI_EN",
+ "SPKR_I2C_SDA",
+ "SPKR_I2C_SCL",
+ "FOD_INT_N1",
+ "FOD_RST",
+ "SMB_SPMI_DATA", /* GPIO_40 */
+ "SMB_SPMI_CLK",
+ "WLS_CHARGE_CTRL",
+ "FORCED_USB_BOOT",
+ "SPKR_INT",
+ "LCD_ID_DET1",
+ "CHARGER_UART_TX",
+ "CHARGER_UART_RX",
+ "TP_SPI_MISO",
+ "TP_SPI_MOSI",
+ "TP_SPI_CLK", /* GPIO_50 */
+ "TP_SPI_CS",
+ "FOD_SPI_MISO",
+ "FOD_SPI_MOSI",
+ "FOD_SPI_CLK",
+ "FOD_SPI_CS",
+ "NFC_SE_SPI_MISO",
+ "NFC_SE_SPI_MOSI",
+ "NFC_SE_SPI_CLK",
+ "NFC_SE_SPI_CS",
+ "NFC_I2C_SDA", /* GPIO_60 */
+ "NFC_I2C_SCL",
+ "NFC_EN",
+ "NFC_CLK_REQ",
+ "HST_WLAN_EN",
+ "HST_BT_EN",
+ "CAMU_AVDD_EN",
+ "VBUS_NTC_CTRL",
+ "HST_BT_UART_CTS",
+ "HST_BT_UART_RFR",
+ "HST_BT_UART_TX", /* GPIO_70 */
+ "HST_BT_UART_RX",
+ "ADSP_FG_I2C_SDA",
+ "ADSP_FG_I2C_SCL",
+ "DISP_RATE",
+ "ERR_INT_N",
+ "TOF_SPI_MISO",
+ "TOF_SPI_MOSI",
+ "TOF_SPI_CLK",
+ "TOF_SPI_CS",
+ "HALL_OUT1", /* GPIO_80 */
+ "USB_CC_DIR",
+ "MDP_VSYNC_P",
+ "SEC_AMOLED_TE_DIS",
+ "FLICKER_INT",
+ "HALL_OUT2",
+ "NFC_DWL_REQ",
+ "NFC_INT_REQ",
+ "WCD_RESET_N",
+ "ALS_INT_N",
+ "GPIO_BQ25970_MASTER_INT", /* GPIO_90 */
+ "GYRO_INT",
+ "NC",
+ "CAMF_DVDD_EN",
+ "PCIE0_RESET_N",
+ "PCIE0_CLK_REQ_N",
+ "PCIE0_WAKE_N",
+ "RF_CABLE_INT2",
+ "NC",
+ "TOF_IRQ",
+ "CAM_MCLK0", /* GPIO_100 */
+ "CAM_MCLK1",
+ "CAM_MCLK2",
+ "CAM_MCLK3",
+ "NC",
+ "CAM_MCLK5",
+ "CAM3_RESET_N",
+ "CCI_I2C0_SDA",
+ "CCI_I2C0_SCL",
+ "CCI_I2C1_SDA",
+ "CCI_I2C1_SCL", /* GPIO_110 */
+ "CCI_I2C2_SDA",
+ "CCI_I2C2_SCL",
+ "CCI_I2C3_SDA",
+ "CCI_I2C3_SCL",
+ "SEC_AMOLED_TP_3P3_EN",
+ "SPKR_PA_INT",
+ "CAM2_RESET_N",
+ "ACCEL_INT",
+ "HAP_DRV_INT",
+ "SPKR_I2S_BCK", /* GPIO_120 */
+ "SPKR_I2S_DIN",
+ "SPKR_I2S_WS",
+ "GPIO_BQ25970_SLAVE_INT",
+ "SPKR_I2S_DOUT",
+ "SEC_AMOLED_TP_RST",
+ "RF_CABLE_INT1",
+ "WLS_QUCK_EN",
+ "NC",
+ "HST_BT_WLAN_SLIMBUS_CLK",
+ "HST_BT_WLAN_SLIMBUS_DAT0", /* GPIO_130 */
+ "NC",
+ "TP_3P3_EN",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_PRESENT",
+ "UIM1_DATA",
+ "UIM1_CLK",
+ "UIM1_RESET",
+ "UIM1_PRESENT", /* GPIO_140 */
+ "SM_RFFE0_CLK",
+ "SM_RFFE0_DATA",
+ "SM_RFFE1_CLK",
+ "SM_RFFE1_DATA",
+ "SM_RFFE2_CLK",
+ "SM_RFFE2_DATA",
+ "SM_RFFE3_CLK",
+ "SM_RFFE3_DATA",
+ "SM_RFFE4_CLK",
+ "SM_RFFE4_DATA", /* GPIO_150 */
+ "WLAN_COEX_UART1_RX",
+ "WLAN_COEX_UART1_TX",
+ "HST_SW_CTRL",
+ "SEC_AMOLED_VDDI_TP_EN",
+ "HAP_DRV_RSTN",
+ "NC",
+ "NC",
+ "NC",
+ "QLINK0_REQ",
+ "QLINK0_EN", /* GPIO_160 */
+ "QLINK0_WMSS_RESET_N",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RF_CABLE_INT3",
+ "NC",
+ "WCD_SWR_TX_CLK",
+ "WCD_SWR_TX_DATA0",
+ "WCD_SWR_TX_DATA1", /* GPIO_170 */
+ "HAP_SWR_RX_CLK",
+ "HAP_SWR_RX_DATA0",
+ "WCD_SWR_RX_DATA1",
+ "NC",
+ "CAMW_DVDD_EN",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_180 */
+ "NC",
+ "WCD_SWR_TX_DATA2",
+ "ACC_I3C_SDA",
+ "ACC_I3C_SCL",
+ "SSC_SENSOR_I2C1_SDA",
+ "SSC_SENSOR_I2C1_SCL",
+ "NC",
+ "TCS3718_GPIO",
+ "NC",
+ "NC", /* GPIO_190 */
+ "SSC_MAG_I2C_SDA",
+ "SSC_MAG_I2C_SCL",
+ "SSC_SENSOR_I2C_SDA",
+ "SSC_SENSOR_I2C_SCL",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "HST_BLE_UART_TX",
+ "HST_BLE_UART_RX", /* GPIO_200 */
+ "HST_WLAN_UART_TX",
+ "HST_WLAN_UART_RX";
+
+ pcie0_default_state: pcie0-default-state {
+ perst-pins {
+ pins = "gpio94";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ clkreq-pins {
+ pins = "gpio95";
+ function = "pcie0_clkreqn";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake-pins {
+ pins = "gpio96";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ qup_spi1_default: qup-spi1-default-state {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "qup1";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ qup_spi11_default: qup-spi11-default-state {
+ pins = "gpio48", "gpio49", "gpio50", "gpio51";
+ function = "qup11";
+ drive-strength = <6>;
+ bias-disable;
+ };
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l7b_2p96>;
+ vcc-max-microamp = <800000>;
+ vccq-supply = <&vreg_l9b_1p2>;
+ vccq-max-microamp = <900000>;
+ vdd-hba-supply = <&vreg_l9b_1p2>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l5b_0p88>;
+ vdda-pll-supply = <&vreg_l6b_1p2>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ /* USB 2.0 only */
+ qcom,select-utmi-as-pipe-clk;
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+ maximum-speed = "high-speed";
+ /* Remove USB3 phy */
+ phys = <&usb_1_hsphy>;
+ phy-names = "usb2-phy";
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l5b_0p88>;
+ vdda18-supply = <&vreg_l1c_1p8>;
+ vdda33-supply = <&vreg_l2b_3p07>;
+
+ status = "okay";
+};
\ No newline at end of file
--
2.42.0
On Sat, 21 Oct 2023 at 13:20, Xilin Wu via B4 Relay
<[email protected]> wrote:
>
> From: Xilin Wu <[email protected]>
>
> UCSI is supported on SM8350. Allow it to enable USB role switch and
> altmode notifications on SM8350.
We have had troubles with UCSI on sm8350. I have a workaround for this
(and earlier) platforms. Once it is ready to be posted, I'll include
your patch in the series, if you don't mind.
>
> Signed-off-by: Xilin Wu <[email protected]>
> ---
> drivers/soc/qcom/pmic_glink.c | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
> index 914057331afd..1196e79e6fb3 100644
> --- a/drivers/soc/qcom/pmic_glink.c
> +++ b/drivers/soc/qcom/pmic_glink.c
> @@ -341,6 +341,7 @@ static const unsigned long pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT
> BIT(PMIC_GLINK_CLIENT_UCSI);
>
> static const struct of_device_id pmic_glink_of_match[] = {
> + { .compatible = "qcom,sm8350-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> { .compatible = "qcom,pmic-glink" },
>
> --
> 2.42.0
>
--
With best wishes
Dmitry
Dmitry Baryshkov <[email protected]> 于2023年10月22日周日 18:51写道：
>
> On Sat, 21 Oct 2023 at 13:20, Xilin Wu via B4 Relay
> <[email protected]> wrote:
> >
> > From: Xilin Wu <[email protected]>
> >
> > UCSI is supported on SM8350. Allow it to enable USB role switch and
> > altmode notifications on SM8350.
>
> We have had troubles with UCSI on sm8350. I have a workaround for this
> (and earlier) platforms. Once it is ready to be posted, I'll include
> your patch in the series, if you don't mind.
I don't mind of course. Do I possibly need to resend the series without the
pmic_glink patch?
>
> >
> > Signed-off-by: Xilin Wu <[email protected]>
> > ---
> > drivers/soc/qcom/pmic_glink.c | 1 +
> > 1 file changed, 1 insertion(+)
> >
> > diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
> > index 914057331afd..1196e79e6fb3 100644
> > --- a/drivers/soc/qcom/pmic_glink.c
> > +++ b/drivers/soc/qcom/pmic_glink.c
> > @@ -341,6 +341,7 @@ static const unsigned long pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT
> > BIT(PMIC_GLINK_CLIENT_UCSI);
> >
> > static const struct of_device_id pmic_glink_of_match[] = {
> > + { .compatible = "qcom,sm8350-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > { .compatible = "qcom,pmic-glink" },
> >
> > --
> > 2.42.0
> >
>
>
> --
> With best wishes
> Dmitry
On Mon, 23 Oct 2023 at 08:06, Sophon Wu <[email protected]> wrote:
>
> Dmitry Baryshkov <[email protected]> 于2023年10月22日周日 18:51写道：
> >
> > On Sat, 21 Oct 2023 at 13:20, Xilin Wu via B4 Relay
> > <[email protected]> wrote:
> > >
> > > From: Xilin Wu <[email protected]>
> > >
> > > UCSI is supported on SM8350. Allow it to enable USB role switch and
> > > altmode notifications on SM8350.
> >
> > We have had troubles with UCSI on sm8350. I have a workaround for this
> > (and earlier) platforms. Once it is ready to be posted, I'll include
> > your patch in the series, if you don't mind.
>
> I don't mind of course. Do I possibly need to resend the series without the
> pmic_glink patch?
That depends on the review of the patch 3/3. If there are any
comments, you'll have to resend. If not, maintainers can pick it up
separately.
> >
> > >
> > > Signed-off-by: Xilin Wu <[email protected]>
> > > ---
> > > drivers/soc/qcom/pmic_glink.c | 1 +
> > > 1 file changed, 1 insertion(+)
> > >
> > > diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
> > > index 914057331afd..1196e79e6fb3 100644
> > > --- a/drivers/soc/qcom/pmic_glink.c
> > > +++ b/drivers/soc/qcom/pmic_glink.c
> > > @@ -341,6 +341,7 @@ static const unsigned long pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT
> > > BIT(PMIC_GLINK_CLIENT_UCSI);
> > >
> > > static const struct of_device_id pmic_glink_of_match[] = {
> > > + { .compatible = "qcom,sm8350-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > > { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > > { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > > { .compatible = "qcom,pmic-glink" },
> > >
> > > --
> > > 2.42.0
> > >
> >
> >
> > --
> > With best wishes
> > Dmitry
--
With best wishes
Dmitry
On Sun, 22 Oct 2023 at 13:51, Dmitry Baryshkov
<[email protected]> wrote:
>
> On Sat, 21 Oct 2023 at 13:20, Xilin Wu via B4 Relay
> <[email protected]> wrote:
> >
> > From: Xilin Wu <[email protected]>
> >
> > UCSI is supported on SM8350. Allow it to enable USB role switch and
> > altmode notifications on SM8350.
>
> We have had troubles with UCSI on sm8350. I have a workaround for this
> (and earlier) platforms. Once it is ready to be posted, I'll include
> your patch in the series, if you don't mind.
I ended up fixing the pmic_glink in a slightly different way, so I'll
include a different patch in the posting.
>
> >
> > Signed-off-by: Xilin Wu <[email protected]>
> > ---
> > drivers/soc/qcom/pmic_glink.c | 1 +
> > 1 file changed, 1 insertion(+)
> >
> > diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
> > index 914057331afd..1196e79e6fb3 100644
> > --- a/drivers/soc/qcom/pmic_glink.c
> > +++ b/drivers/soc/qcom/pmic_glink.c
> > @@ -341,6 +341,7 @@ static const unsigned long pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT
> > BIT(PMIC_GLINK_CLIENT_UCSI);
> >
> > static const struct of_device_id pmic_glink_of_match[] = {
> > + { .compatible = "qcom,sm8350-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > { .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > { .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
> > { .compatible = "qcom,pmic-glink" },
> >
> > --
> > 2.42.0
> >
>
>
> --
> With best wishes
> Dmitry
--
With best wishes
Dmitry
On 21.10.2023 12:20, Xilin Wu via B4 Relay wrote:
> From: Xilin Wu <[email protected]>
>
> Add support for Xiaomi Mi 11 Ultra. This commit brings support for:
> * Front and rear display panels (initialized by bootloader)
> * USB
> * UFS
> * PCIe0
> * Thermistor sensors
> * ADSP/CDSP/Modem/SLPI
> * IR Transmitter
> * RTC provided by PMK8350
> * Buttons
>
> To create a working boot image, you need to run:
> cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/sm8350-xiaomi-\
> star.dtb > .Image.gz-dtb
>
> mkbootimg \
> --kernel .Image.gz-dtb \
> --ramdisk some_initrd.img \
> --pagesize 4096 \
> --base 0x0 \
> --kernel_offset 0x8000 \
> --ramdisk_offset 0x1000000 \
> --tags_offset 0x100 \
> --cmdline "SOME_CMDLINE" \
> --dtb_offset 0x1f00000 \
> --header_version 1 \
> --os_version 14.0.0 \
> --os_patch_level 2099-12 \
> -o boot.img-xiaomi-star
>
> Then, you can flash it to slot b on the device:
>
> // You have to either pull vbmeta{"","_system"} from
> // /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
> fastboot --disable-verity --disable-verification flash vbmeta_b vbmeta.img
> fastboot --disable-verity --disable-verification flash vbmeta_system_b \
> vbmeta_system.img
>
> fastboot flash boot_b boot.img-xiaomi-star
> fastboot erase dtbo_b
> fastboot set_active b
> fastboot reboot
>
> Signed-off-by: Xilin Wu <[email protected]>
> ---
[...]
> + pmr735a_s1: smps1 {
> + regulator-name = "pmr735a_s1";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1280000>;
> + };
You probably want initial mode on this pmic too
[...]
> +
> +&ufs_mem_hc {
> + reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>;
> + vcc-supply = <&vreg_l7b_2p96>;
> + vcc-max-microamp = <800000>;
> + vccq-supply = <&vreg_l9b_1p2>;
> + vccq-max-microamp = <900000>;
> + vdd-hba-supply = <&vreg_l9b_1p2>;
These regulators need regulator-allow-set-mode and allowed-modes
Konrad
[...]
> \ No newline at end of file
>
And this needs to be fixed
looks good otherwise, I think!
Konrad