From: Andrea Merello <[email protected]>
This series (tries to) add support for Bosch BNO055 IMU to Linux IIO
subsystem. It is made up several patches:
1/13 to 7/12: add some IIO modifiers, and their documentation, to the IIO
core layer, in order to being able to expose the linear
acceleration and Euler angles among standard attributes.
Also update the IIO event monitor tool
7/13: fix binary attributes didn't work with IIO
8/13 to 11/13: add the core IIO BNO055 driver and documentation for sysfs
attributes and DT bindings
12/13: adds serdev BNO055 driver to actually use the IMU via serial line
13/13: adds I2C BNO055 driver to actually use the IMU via I2C wiring
14/13: add a documentation file that describe the bno055 driver and
specifically the calibration
Differences wrt v3:
- use binary attribute for calibration data
- introduce trace events (instead of dev_dbg()) for bno055 serial driver
- changed serial driver name bno055_sl -> bno055_ser
- fix quaternion unit
- make the driver return error, instead of reading zeroes, when trying to
access fusion data, but fusion is disabled
- make serial driver code more readable and use more kernel helpers when
possible
- address issues found by 0day
- fix accel range unit in doc
- fix debugfs directory was not ever removed
- add of_device_id table in I2C driver
- use probe_new() instead of probe in I2C driver
- some other trivial improvements and fixes
Differences wrt other BNO055 drivers:
Previously at least another driver for the very same chip has been posted
to the Linux ML [0], but it has been never merged, and it seems no one
cared of it since quite a long time.
This driver differs from the above driver on the following aspects:
- This driver supports also serial access (to be reliable, reset pin is
required to be wired)
- The above driver tried to support all IMU HW modes by allowing to
choose one in the DT, and adapting IIO attributes accordingly. This
driver does not rely on DT for this, instead settings are done via
sysfs attributes. All IIO attributes are always exposed; more on this
later on. This driver however supports only a subset of the
HW-supported modes.
- This driver has some support for managing the IMU calibration
Supported operation modes:
- AMG (accelerometer, magnetometer and gyroscope) mode, which provides
raw (uncalibrated) measurements from the said sensors, and allows for
setting some parameters about them (e.g. filter cut-off frequency, max
sensor ranges, etc).
- Fusion mode, which still provides AMG measures, while it also provides
other data calculated by the IMU (e.g. rotation angles, linear
acceleration, etc). In this mode user has no freedom to set any sensor
parameter, since the HW locks them. Autocalibration and correction is
performed by the IMU.
IIO attributes exposing sensors parameters are always present, but in
fusion modes the available values are constrained to just the one used by
the HW. This is reflected in the '*_available' IIO attributes.
Trying to set a not-supported value always falls back to the closest
supported one, which in this case is just the one in use by the HW.
IIO attributes for unavailable measurements (e.g. Euler angles in AMG
mode) can't be read (return -EBUSY, or refuse to enable buffer).
IMU calibration:
The IMU supports for two sets of calibration parameters:
- SIC matrix. user-provided; this driver doesn't currently support it
- Offset and radius parameters. The IMU automatically finds out them when
it is running in fusion mode; supported by this driver.
The driver provides access to autocalibration flags (i.e. you can known
if the IMU has successfully autocalibrated) and to calibration data blob.
The user can save this blob in a "firmware" file (i.e. in /lib/firmware)
that the driver looks for at probe time. If found, then the IMU is
initialized with this calibration data. This saves the user from
performing the calibration procedure every time (which consist of moving
the IMU in various way).
The driver looks for calibration data file using two different names:
first a file whose name is suffixed with the IMU unique ID is searched
for; this is useful when there is more than one IMU instance. If this
file is not found, then a "generic" calibration file is searched for
(which can be used when only one IMU is present, without struggling with
fancy names, that changes on each device).
In AMG mode the IIO 'offset' attributes provide access to the offsets
from calibration data (if any), so that the user can apply them to the
accel, angvel and magn IIO attributes. In fusion mode they are not needed
and read as zero.
Access protocols and serdev module:
The serial protocol is quite simple, but there are tricks to make it
really works. Those tricks and workarounds are documented in the driver
source file.
The core BNO055 driver tries to group readings in burst when appropriate,
in order to optimize triggered buffer operation. The threshold for
splitting a burst (i.e. max number of unused bytes in the middle of a
burst that will be throw away) is provided to the core driver by the
lowlevel access driver (either serdev or I2C) at probe time.
[0] https://www.spinics.net/lists/linux-iio/msg25508.html
Andrea Merello (14):
iio: add modifiers for linear acceleration
iio: document linear acceleration modifiers
iio: event_monitor: add linear acceleration modifiers
iio: add modifers for pitch, yaw, roll
iio: document pitch, yaw, roll modifiers
iio: event_monitor: add pitch, yaw and roll modifiers
iio: add support for binary attributes
iio: imu: add Bosch Sensortec BNO055 core driver
iio: document bno055 private sysfs attributes
iio: document "serial_number" sysfs attribute
dt-bindings: iio: imu: add documentation for Bosch BNO055 bindings
iio: imu: add BNO055 serdev driver
iio: imu: add BNO055 I2C driver
docs: iio: add documentation for BNO055 driver
Documentation/ABI/testing/sysfs-bus-iio | 25 +
.../ABI/testing/sysfs-bus-iio-bno055 | 81 +
.../bindings/iio/imu/bosch,bno055.yaml | 59 +
Documentation/iio/bno055.rst | 50 +
Documentation/iio/index.rst | 2 +
drivers/iio/imu/Kconfig | 1 +
drivers/iio/imu/Makefile | 1 +
drivers/iio/imu/bno055/Kconfig | 31 +
drivers/iio/imu/bno055/Makefile | 7 +
drivers/iio/imu/bno055/bno055.c | 1715 +++++++++++++++++
drivers/iio/imu/bno055/bno055.h | 12 +
drivers/iio/imu/bno055/bno055_i2c.c | 56 +
drivers/iio/imu/bno055/bno055_ser.c | 556 ++++++
drivers/iio/imu/bno055/bno055_ser_trace.h | 114 ++
drivers/iio/industrialio-core.c | 10 +-
include/uapi/linux/iio/types.h | 7 +-
tools/iio/iio_event_monitor.c | 6 +
17 files changed, 2731 insertions(+), 2 deletions(-)
create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-bno055
create mode 100644 Documentation/devicetree/bindings/iio/imu/bosch,bno055.yaml
create mode 100644 Documentation/iio/bno055.rst
create mode 100644 drivers/iio/imu/bno055/Kconfig
create mode 100644 drivers/iio/imu/bno055/Makefile
create mode 100644 drivers/iio/imu/bno055/bno055.c
create mode 100644 drivers/iio/imu/bno055/bno055.h
create mode 100644 drivers/iio/imu/bno055/bno055_i2c.c
create mode 100644 drivers/iio/imu/bno055/bno055_ser.c
create mode 100644 drivers/iio/imu/bno055/bno055_ser_trace.h
--
2.17.1
From: Andrea Merello <[email protected]>
This patch adds a core driver for the BNO055 IMU from Bosch. This IMU
can be connected via both serial and I2C busses; separate patches will
add support for them.
The driver supports "AMG" (Accelerometer, Magnetometer, Gyroscope) mode,
that provides raw data from the said internal sensors, and a couple of
"fusion" modes (i.e. the IMU also do calculations in order to provide
euler angles, quaternions, linear acceleration and gravity measurements).
In fusion modes the AMG data is still available (with some calibration
refinements done by the IMU), but certain settings such as low pass
filters cut-off frequency and sensors ranges are fixed, while in AMG mode
they can be customized; this is why AMG mode can still be interesting.
Signed-off-by: Andrea Merello <[email protected]>
---
drivers/iio/imu/Kconfig | 1 +
drivers/iio/imu/Makefile | 1 +
drivers/iio/imu/bno055/Kconfig | 4 +
drivers/iio/imu/bno055/Makefile | 3 +
drivers/iio/imu/bno055/bno055.c | 1715 +++++++++++++++++++++++++++++++
drivers/iio/imu/bno055/bno055.h | 12 +
6 files changed, 1736 insertions(+)
create mode 100644 drivers/iio/imu/bno055/Kconfig
create mode 100644 drivers/iio/imu/bno055/Makefile
create mode 100644 drivers/iio/imu/bno055/bno055.c
create mode 100644 drivers/iio/imu/bno055/bno055.h
diff --git a/drivers/iio/imu/Kconfig b/drivers/iio/imu/Kconfig
index 001ca2c3ff95..f1d7d4b5e222 100644
--- a/drivers/iio/imu/Kconfig
+++ b/drivers/iio/imu/Kconfig
@@ -52,6 +52,7 @@ config ADIS16480
ADIS16485, ADIS16488 inertial sensors.
source "drivers/iio/imu/bmi160/Kconfig"
+source "drivers/iio/imu/bno055/Kconfig"
config FXOS8700
tristate
diff --git a/drivers/iio/imu/Makefile b/drivers/iio/imu/Makefile
index c82748096c77..6eb612034722 100644
--- a/drivers/iio/imu/Makefile
+++ b/drivers/iio/imu/Makefile
@@ -15,6 +15,7 @@ adis_lib-$(CONFIG_IIO_ADIS_LIB_BUFFER) += adis_buffer.o
obj-$(CONFIG_IIO_ADIS_LIB) += adis_lib.o
obj-y += bmi160/
+obj-y += bno055/
obj-$(CONFIG_FXOS8700) += fxos8700_core.o
obj-$(CONFIG_FXOS8700_I2C) += fxos8700_i2c.o
diff --git a/drivers/iio/imu/bno055/Kconfig b/drivers/iio/imu/bno055/Kconfig
new file mode 100644
index 000000000000..d0ab3221fba5
--- /dev/null
+++ b/drivers/iio/imu/bno055/Kconfig
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config BOSCH_BNO055_IIO
+ tristate
diff --git a/drivers/iio/imu/bno055/Makefile b/drivers/iio/imu/bno055/Makefile
new file mode 100644
index 000000000000..56cc4de60a7e
--- /dev/null
+++ b/drivers/iio/imu/bno055/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_BOSCH_BNO055_IIO) += bno055.o
diff --git a/drivers/iio/imu/bno055/bno055.c b/drivers/iio/imu/bno055/bno055.c
new file mode 100644
index 000000000000..396b3f87f907
--- /dev/null
+++ b/drivers/iio/imu/bno055/bno055.c
@@ -0,0 +1,1715 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * IIO driver for Bosch BNO055 IMU
+ *
+ * Copyright (C) 2021-2022 Istituto Italiano di Tecnologia
+ * Electronic Design Laboratory
+ * Written by Andrea Merello <[email protected]>
+ *
+ * Portions of this driver are taken from the BNO055 driver patch
+ * from Vlad Dogaru which is Copyright (c) 2016, Intel Corporation.
+ *
+ * This driver is also based on BMI160 driver, which is:
+ * Copyright (c) 2016, Intel Corporation.
+ * Copyright (c) 2019, Martin Kelly.
+ */
+
+#include <linux/bitmap.h>
+#include <linux/clk.h>
+#include <linux/bitfield.h>
+#include <linux/debugfs.h>
+#include <linux/device.h>
+#include <linux/firmware.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/regmap.h>
+#include <linux/util_macros.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/buffer.h>
+#include <linux/iio/sysfs.h>
+
+#include "bno055.h"
+
+#define BNO055_FW_NAME "bno055-caldata"
+#define BNO055_FW_EXT ".dat"
+#define BNO055_FW_UID_NAME BNO055_FW_NAME "-%*phN" BNO055_FW_EXT
+#define BNO055_FW_GENERIC_NAME (BNO055_FW_NAME BNO055_FW_EXT)
+
+/* common registers */
+#define BNO055_PAGESEL_REG 0x7
+
+/* page 0 registers */
+#define BNO055_CHIP_ID_REG 0x0
+#define BNO055_CHIP_ID_MAGIC 0xA0
+#define BNO055_SW_REV_LSB_REG 0x4
+#define BNO055_SW_REV_MSB_REG 0x5
+#define BNO055_ACC_DATA_X_LSB_REG 0x8
+#define BNO055_ACC_DATA_Y_LSB_REG 0xA
+#define BNO055_ACC_DATA_Z_LSB_REG 0xC
+#define BNO055_MAG_DATA_X_LSB_REG 0xE
+#define BNO055_MAG_DATA_Y_LSB_REG 0x10
+#define BNO055_MAG_DATA_Z_LSB_REG 0x12
+#define BNO055_GYR_DATA_X_LSB_REG 0x14
+#define BNO055_GYR_DATA_Y_LSB_REG 0x16
+#define BNO055_GYR_DATA_Z_LSB_REG 0x18
+#define BNO055_EUL_DATA_X_LSB_REG 0x1A
+#define BNO055_EUL_DATA_Y_LSB_REG 0x1C
+#define BNO055_EUL_DATA_Z_LSB_REG 0x1E
+#define BNO055_QUAT_DATA_W_LSB_REG 0x20
+#define BNO055_LIA_DATA_X_LSB_REG 0x28
+#define BNO055_LIA_DATA_Y_LSB_REG 0x2A
+#define BNO055_LIA_DATA_Z_LSB_REG 0x2C
+#define BNO055_GRAVITY_DATA_X_LSB_REG 0x2E
+#define BNO055_GRAVITY_DATA_Y_LSB_REG 0x30
+#define BNO055_GRAVITY_DATA_Z_LSB_REG 0x32
+#define BNO055_SCAN_CH_COUNT ((BNO055_GRAVITY_DATA_Z_LSB_REG - BNO055_ACC_DATA_X_LSB_REG) / 2)
+#define BNO055_TEMP_REG 0x34
+#define BNO055_CALIB_STAT_REG 0x35
+#define BNO055_CALIB_STAT_MASK GENMASK(1, 0)
+#define BNO055_CALIB_STAT_MAGN_SHIFT 0
+#define BNO055_CALIB_STAT_ACCEL_SHIFT 2
+#define BNO055_CALIB_STAT_GYRO_SHIFT 4
+#define BNO055_CALIB_STAT_SYS_SHIFT 6
+#define BNO055_SYS_ERR_REG 0x3A
+#define BNO055_POWER_MODE_REG 0x3E
+#define BNO055_POWER_MODE_NORMAL 0
+#define BNO055_SYS_TRIGGER_REG 0x3F
+#define BNO055_SYS_TRIGGER_RST_SYS BIT(5)
+#define BNO055_SYS_TRIGGER_CLK_SEL BIT(7)
+#define BNO055_OPR_MODE_REG 0x3D
+#define BNO055_OPR_MODE_CONFIG 0x0
+#define BNO055_OPR_MODE_AMG 0x7
+#define BNO055_OPR_MODE_FUSION_FMC_OFF 0xB
+#define BNO055_OPR_MODE_FUSION 0xC
+#define BNO055_UNIT_SEL_REG 0x3B
+/* Android orientation mode means: pitch value decreases turning clockwise */
+#define BNO055_UNIT_SEL_ANDROID BIT(7)
+#define BNO055_UNIT_SEL_GYR_RPS BIT(1)
+#define BNO055_CALDATA_START 0x55
+#define BNO055_CALDATA_END 0x6A
+#define BNO055_CALDATA_LEN 22
+
+/*
+ * The difference in address between the register that contains the
+ * value and the register that contains the offset. This applies for
+ * accel, gyro and magn channels.
+ */
+#define BNO055_REG_OFFSET_ADDR 0x4D
+
+/* page 1 registers */
+#define BNO055_PG1(x) ((x) | 0x80)
+#define BNO055_ACC_CONFIG_REG BNO055_PG1(0x8)
+#define BNO055_ACC_CONFIG_LPF_MASK GENMASK(4, 2)
+#define BNO055_ACC_CONFIG_RANGE_MASK GENMASK(1, 0)
+#define BNO055_MAG_CONFIG_REG BNO055_PG1(0x9)
+#define BNO055_MAG_CONFIG_HIGHACCURACY 0x18
+#define BNO055_MAG_CONFIG_ODR_MASK GENMASK(2, 0)
+#define BNO055_GYR_CONFIG_REG BNO055_PG1(0xA)
+#define BNO055_GYR_CONFIG_RANGE_MASK GENMASK(2, 0)
+#define BNO055_GYR_CONFIG_LPF_MASK GENMASK(5, 3)
+#define BNO055_GYR_AM_SET_REG BNO055_PG1(0x1F)
+#define BNO055_UID_LOWER_REG BNO055_PG1(0x50)
+#define BNO055_UID_HIGHER_REG BNO055_PG1(0x5F)
+#define BNO055_UID_LEN 16
+
+struct bno055_sysfs_attr {
+ int *vals;
+ int len;
+ int *fusion_vals;
+ int *hw_xlate;
+ int type;
+};
+
+#define BNO055_ATTR_VALS(...) \
+ .vals = (int[]){ __VA_ARGS__}, \
+ .len = ARRAY_SIZE(((int[]){__VA_ARGS__}))
+
+static struct bno055_sysfs_attr bno055_acc_lpf = {
+ BNO055_ATTR_VALS(7, 810000, 15, 630000,
+ 31, 250000, 62, 500000, 125, 0,
+ 250, 0, 500, 0, 1000, 0),
+ .fusion_vals = (int[]){62, 500000},
+ .type = IIO_VAL_INT_PLUS_MICRO
+};
+
+static struct bno055_sysfs_attr bno055_acc_range = {
+ /* G: 2, 4, 8, 16 */
+ BNO055_ATTR_VALS(1962, 3924, 7848, 15696),
+ .fusion_vals = (int[]){3924}, /* 4G */
+ .type = IIO_VAL_INT
+};
+
+/*
+ * Theoretically the IMU should return data in a given (i.e. fixed) unit
+ * regardless the range setting. This happens for the accelerometer, but not for
+ * the gyroscope; the gyroscope range setting affects the scale.
+ * This is probably due to this[0] bug.
+ * For this reason we map the internal range setting onto the standard IIO scale
+ * attribute for gyro.
+ * Since the bug[0] may be fixed in future, we check for the IMU FW version and
+ * eventually warn the user.
+ * Currently we just don't care about "range" attributes for gyro.
+ *
+ * [0] https://community.bosch-sensortec.com/t5/MEMS-sensors-forum/BNO055-Wrong-sensitivity-resolution-in-datasheet/td-p/10266
+ */
+static struct bno055_sysfs_attr bno055_gyr_scale = {
+ /*
+ * dps = hwval * (dps_range/2^15)
+ * rps = hwval * (rps_range/2^15)
+ * = hwval * (dps_range/(2^15 * k))
+ * where k is rad-to-deg factor
+ */
+ BNO055_ATTR_VALS(125, 1877467, 250, 1877467,
+ 500, 1877467, 1000, 1877467,
+ 2000, 1877467),
+ .fusion_vals = (int[]){1, 900},
+ .hw_xlate = (int[]){4, 3, 2, 1, 0},
+ .type = IIO_VAL_FRACTIONAL
+};
+
+static struct bno055_sysfs_attr bno055_gyr_lpf = {
+ BNO055_ATTR_VALS(12, 23, 32, 47, 64, 116, 230, 523),
+ .fusion_vals = (int[]){32},
+ .hw_xlate = (int[]){5, 4, 7, 3, 6, 2, 1, 0},
+ .type = IIO_VAL_INT
+};
+
+static struct bno055_sysfs_attr bno055_mag_odr = {
+ BNO055_ATTR_VALS(2, 6, 8, 10, 15, 20, 25, 30),
+ .fusion_vals = (int[]){20},
+ .type = IIO_VAL_INT
+};
+
+struct bno055_priv {
+ struct regmap *regmap;
+ struct device *dev;
+ struct clk *clk;
+ int operation_mode;
+ int xfer_burst_break_thr;
+ struct mutex lock;
+ u8 uid[BNO055_UID_LEN];
+ struct gpio_desc *reset_gpio;
+ bool sw_reset;
+ struct {
+ __le16 chans[BNO055_SCAN_CH_COUNT];
+ s64 timestamp __aligned(8);
+ } buf;
+#ifdef CONFIG_DEBUG_FS
+ struct dentry *debugfs;
+#endif
+};
+
+static bool bno055_regmap_volatile(struct device *dev, unsigned int reg)
+{
+ /* data and status registers */
+ if (reg >= BNO055_ACC_DATA_X_LSB_REG && reg <= BNO055_SYS_ERR_REG)
+ return true;
+
+ /* when in fusion mode, config is updated by chip */
+ if (reg == BNO055_MAG_CONFIG_REG ||
+ reg == BNO055_ACC_CONFIG_REG ||
+ reg == BNO055_GYR_CONFIG_REG)
+ return true;
+
+ /* calibration data may be updated by the IMU */
+ if (reg >= BNO055_CALDATA_START && reg <= BNO055_CALDATA_END)
+ return true;
+
+ return false;
+}
+
+static bool bno055_regmap_readable(struct device *dev, unsigned int reg)
+{
+ /* unnamed PG0 reserved areas */
+ if ((reg < BNO055_PG1(0) && reg > BNO055_CALDATA_END) ||
+ reg == 0x3C)
+ return false;
+
+ /* unnamed PG1 reserved areas */
+ if (reg > BNO055_PG1(BNO055_UID_HIGHER_REG) ||
+ (reg < BNO055_PG1(BNO055_UID_LOWER_REG) && reg > BNO055_PG1(BNO055_GYR_AM_SET_REG)) ||
+ reg == BNO055_PG1(0xE) ||
+ (reg < BNO055_PG1(BNO055_PAGESEL_REG) && reg >= BNO055_PG1(0x0)))
+ return false;
+ return true;
+}
+
+static bool bno055_regmap_writeable(struct device *dev, unsigned int reg)
+{
+ /*
+ * Unreadable registers are indeed reserved; there are no WO regs
+ * (except for a single bit in SYS_TRIGGER register)
+ */
+ if (!bno055_regmap_readable(dev, reg))
+ return false;
+
+ /* data and status registers */
+ if (reg >= BNO055_ACC_DATA_X_LSB_REG && reg <= BNO055_SYS_ERR_REG)
+ return false;
+
+ /* ID areas */
+ if (reg < BNO055_PAGESEL_REG ||
+ (reg <= BNO055_UID_HIGHER_REG && reg >= BNO055_UID_LOWER_REG))
+ return false;
+
+ return true;
+}
+
+static const struct regmap_range_cfg bno055_regmap_ranges[] = {
+ {
+ .range_min = 0,
+ .range_max = 0x7f * 2,
+ .selector_reg = BNO055_PAGESEL_REG,
+ .selector_mask = GENMASK(7, 0),
+ .selector_shift = 0,
+ .window_start = 0,
+ .window_len = 0x80
+ },
+};
+
+const struct regmap_config bno055_regmap_config = {
+ .name = "bno055",
+ .reg_bits = 8,
+ .val_bits = 8,
+ .ranges = bno055_regmap_ranges,
+ .num_ranges = 1,
+ .volatile_reg = bno055_regmap_volatile,
+ .max_register = 0x80 * 2,
+ .writeable_reg = bno055_regmap_writeable,
+ .readable_reg = bno055_regmap_readable,
+ .cache_type = REGCACHE_RBTREE,
+};
+EXPORT_SYMBOL_NS_GPL(bno055_regmap_config, IIO_BNO055);
+
+/* must be called in configuration mode */
+static int bno055_calibration_load(struct bno055_priv *priv, const u8 *data, int len)
+{
+ if (len != BNO055_CALDATA_LEN) {
+ dev_dbg(priv->dev, "Invalid calibration file size %d (expected %d)",
+ len, BNO055_CALDATA_LEN);
+ return -EINVAL;
+ }
+
+ dev_dbg(priv->dev, "loading cal data: %*ph", BNO055_CALDATA_LEN, data);
+ return regmap_bulk_write(priv->regmap, BNO055_CALDATA_START,
+ data, BNO055_CALDATA_LEN);
+}
+
+static int bno055_operation_mode_do_set(struct bno055_priv *priv,
+ int operation_mode)
+{
+ int ret;
+
+ ret = regmap_write(priv->regmap, BNO055_OPR_MODE_REG,
+ operation_mode);
+ if (ret)
+ return ret;
+
+ msleep(20);
+
+ return 0;
+}
+
+static int bno055_system_reset(struct bno055_priv *priv)
+{
+ int ret;
+
+ if (priv->reset_gpio) {
+ gpiod_set_value_cansleep(priv->reset_gpio, 0);
+ usleep_range(5000, 10000);
+ gpiod_set_value_cansleep(priv->reset_gpio, 1);
+ } else {
+ if (!priv->sw_reset)
+ return 0;
+
+ ret = regmap_write(priv->regmap, BNO055_SYS_TRIGGER_REG,
+ BNO055_SYS_TRIGGER_RST_SYS);
+ if (ret)
+ return ret;
+ }
+
+ regcache_drop_region(priv->regmap, 0x0, 0xff);
+ usleep_range(650000, 700000);
+
+ return 0;
+}
+
+static int bno055_init(struct bno055_priv *priv, const u8 *caldata, int len)
+{
+ int ret;
+
+ ret = bno055_operation_mode_do_set(priv, BNO055_OPR_MODE_CONFIG);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(priv->regmap, BNO055_POWER_MODE_REG,
+ BNO055_POWER_MODE_NORMAL);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(priv->regmap, BNO055_SYS_TRIGGER_REG,
+ priv->clk ? BNO055_SYS_TRIGGER_CLK_SEL : 0);
+ if (ret)
+ return ret;
+
+ /* use standard SI units */
+ ret = regmap_write(priv->regmap, BNO055_UNIT_SEL_REG,
+ BNO055_UNIT_SEL_ANDROID | BNO055_UNIT_SEL_GYR_RPS);
+ if (ret)
+ return ret;
+
+ if (caldata) {
+ ret = bno055_calibration_load(priv, caldata, len);
+ if (ret)
+ dev_warn(priv->dev, "failed to load calibration data with error %d",
+ ret);
+ }
+
+ return 0;
+}
+
+static ssize_t bno055_operation_mode_set(struct bno055_priv *priv,
+ int operation_mode)
+{
+ u8 caldata[BNO055_CALDATA_LEN];
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ ret = bno055_operation_mode_do_set(priv, BNO055_OPR_MODE_CONFIG);
+ if (ret)
+ goto exit;
+
+ if (operation_mode == BNO055_OPR_MODE_FUSION ||
+ operation_mode == BNO055_OPR_MODE_FUSION_FMC_OFF) {
+ /* for entering fusion mode, reset the chip to clear the algo state */
+ ret = regmap_bulk_read(priv->regmap, BNO055_CALDATA_START, caldata,
+ BNO055_CALDATA_LEN);
+ if (ret)
+ goto exit;
+
+ ret = bno055_system_reset(priv);
+ if (ret)
+ goto exit;
+
+ ret = bno055_init(priv, caldata, BNO055_CALDATA_LEN);
+ if (ret)
+ goto exit;
+ }
+
+ ret = bno055_operation_mode_do_set(priv, operation_mode);
+ if (ret)
+ goto exit;
+
+ priv->operation_mode = operation_mode;
+
+exit:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static void bno055_uninit(void *arg)
+{
+ struct bno055_priv *priv = arg;
+
+ /* stop the IMU */
+ bno055_operation_mode_do_set(priv, BNO055_OPR_MODE_CONFIG);
+}
+
+#define BNO055_CHANNEL(_type, _axis, _index, _address, _sep, _sh, _avail) { \
+ .address = _address, \
+ .type = _type, \
+ .modified = 1, \
+ .channel2 = IIO_MOD_##_axis, \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | (_sep), \
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | (_sh), \
+ .info_mask_shared_by_type_available = _avail, \
+ .scan_index = _index, \
+ .scan_type = { \
+ .sign = 's', \
+ .realbits = 16, \
+ .storagebits = 16, \
+ .endianness = IIO_LE, \
+ .repeat = IIO_MOD_##_axis == IIO_MOD_QUATERNION ? 4 : 0 \
+ }, \
+}
+
+/* scan indexes follow DATA register order */
+enum bno055_scan_axis {
+ BNO055_SCAN_ACCEL_X,
+ BNO055_SCAN_ACCEL_Y,
+ BNO055_SCAN_ACCEL_Z,
+ BNO055_SCAN_MAGN_X,
+ BNO055_SCAN_MAGN_Y,
+ BNO055_SCAN_MAGN_Z,
+ BNO055_SCAN_GYRO_X,
+ BNO055_SCAN_GYRO_Y,
+ BNO055_SCAN_GYRO_Z,
+ BNO055_SCAN_YAW,
+ BNO055_SCAN_ROLL,
+ BNO055_SCAN_PITCH,
+ BNO055_SCAN_QUATERNION,
+ BNO055_SCAN_LIA_X,
+ BNO055_SCAN_LIA_Y,
+ BNO055_SCAN_LIA_Z,
+ BNO055_SCAN_GRAVITY_X,
+ BNO055_SCAN_GRAVITY_Y,
+ BNO055_SCAN_GRAVITY_Z,
+ BNO055_SCAN_TIMESTAMP,
+ _BNO055_SCAN_MAX
+};
+
+static const struct iio_chan_spec bno055_channels[] = {
+ /* accelerometer */
+ BNO055_CHANNEL(IIO_ACCEL, X, BNO055_SCAN_ACCEL_X,
+ BNO055_ACC_DATA_X_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY)),
+ BNO055_CHANNEL(IIO_ACCEL, Y, BNO055_SCAN_ACCEL_Y,
+ BNO055_ACC_DATA_Y_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY)),
+ BNO055_CHANNEL(IIO_ACCEL, Z, BNO055_SCAN_ACCEL_Z,
+ BNO055_ACC_DATA_Z_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY)),
+ /* gyroscope */
+ BNO055_CHANNEL(IIO_ANGL_VEL, X, BNO055_SCAN_GYRO_X,
+ BNO055_GYR_DATA_X_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY) |
+ BIT(IIO_CHAN_INFO_SCALE)),
+ BNO055_CHANNEL(IIO_ANGL_VEL, Y, BNO055_SCAN_GYRO_Y,
+ BNO055_GYR_DATA_Y_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY) |
+ BIT(IIO_CHAN_INFO_SCALE)),
+ BNO055_CHANNEL(IIO_ANGL_VEL, Z, BNO055_SCAN_GYRO_Z,
+ BNO055_GYR_DATA_Z_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY),
+ BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY) |
+ BIT(IIO_CHAN_INFO_SCALE)),
+ /* magnetometer */
+ BNO055_CHANNEL(IIO_MAGN, X, BNO055_SCAN_MAGN_X,
+ BNO055_MAG_DATA_X_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_SAMP_FREQ), BIT(IIO_CHAN_INFO_SAMP_FREQ)),
+ BNO055_CHANNEL(IIO_MAGN, Y, BNO055_SCAN_MAGN_Y,
+ BNO055_MAG_DATA_Y_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_SAMP_FREQ), BIT(IIO_CHAN_INFO_SAMP_FREQ)),
+ BNO055_CHANNEL(IIO_MAGN, Z, BNO055_SCAN_MAGN_Z,
+ BNO055_MAG_DATA_Z_LSB_REG, BIT(IIO_CHAN_INFO_OFFSET),
+ BIT(IIO_CHAN_INFO_SAMP_FREQ), BIT(IIO_CHAN_INFO_SAMP_FREQ)),
+ /* euler angle */
+ BNO055_CHANNEL(IIO_ROT, YAW, BNO055_SCAN_YAW,
+ BNO055_EUL_DATA_X_LSB_REG, 0, 0, 0),
+ BNO055_CHANNEL(IIO_ROT, ROLL, BNO055_SCAN_ROLL,
+ BNO055_EUL_DATA_Y_LSB_REG, 0, 0, 0),
+ BNO055_CHANNEL(IIO_ROT, PITCH, BNO055_SCAN_PITCH,
+ BNO055_EUL_DATA_Z_LSB_REG, 0, 0, 0),
+ /* quaternion */
+ BNO055_CHANNEL(IIO_ROT, QUATERNION, BNO055_SCAN_QUATERNION,
+ BNO055_QUAT_DATA_W_LSB_REG, 0, 0, 0),
+
+ /* linear acceleration */
+ BNO055_CHANNEL(IIO_ACCEL, LINEAR_X, BNO055_SCAN_LIA_X,
+ BNO055_LIA_DATA_X_LSB_REG, 0, 0, 0),
+ BNO055_CHANNEL(IIO_ACCEL, LINEAR_Y, BNO055_SCAN_LIA_Y,
+ BNO055_LIA_DATA_Y_LSB_REG, 0, 0, 0),
+ BNO055_CHANNEL(IIO_ACCEL, LINEAR_Z, BNO055_SCAN_LIA_Z,
+ BNO055_LIA_DATA_Z_LSB_REG, 0, 0, 0),
+
+ /* gravity vector */
+ BNO055_CHANNEL(IIO_GRAVITY, X, BNO055_SCAN_GRAVITY_X,
+ BNO055_GRAVITY_DATA_X_LSB_REG, 0, 0, 0),
+ BNO055_CHANNEL(IIO_GRAVITY, Y, BNO055_SCAN_GRAVITY_Y,
+ BNO055_GRAVITY_DATA_Y_LSB_REG, 0, 0, 0),
+ BNO055_CHANNEL(IIO_GRAVITY, Z, BNO055_SCAN_GRAVITY_Z,
+ BNO055_GRAVITY_DATA_Z_LSB_REG, 0, 0, 0),
+
+ {
+ .type = IIO_TEMP,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .scan_index = -1
+ },
+ IIO_CHAN_SOFT_TIMESTAMP(BNO055_SCAN_TIMESTAMP),
+};
+
+static int bno055_get_regmask(struct bno055_priv *priv, int *val, int *val2,
+ int reg, int mask, struct bno055_sysfs_attr *attr)
+{
+ const int shift = __ffs(mask);
+ int hwval, idx;
+ int ret;
+ int i;
+
+ ret = regmap_read(priv->regmap, reg, &hwval);
+ if (ret)
+ return ret;
+
+ idx = (hwval & mask) >> shift;
+ if (attr->hw_xlate)
+ for (i = 0; i < attr->len; i++)
+ if (attr->hw_xlate[i] == idx) {
+ idx = i;
+ break;
+ }
+ if (attr->type == IIO_VAL_INT) {
+ *val = attr->vals[idx];
+ } else { /* IIO_VAL_INT_PLUS_MICRO or IIO_VAL_FRACTIONAL */
+ *val = attr->vals[idx * 2];
+ *val2 = attr->vals[idx * 2 + 1];
+ }
+
+ return attr->type;
+}
+
+static int bno055_set_regmask(struct bno055_priv *priv, int val, int val2,
+ int reg, int mask, struct bno055_sysfs_attr *attr)
+{
+ const int shift = __ffs(mask);
+ int best_delta;
+ int req_val;
+ int tbl_val;
+ bool first;
+ int delta;
+ int hwval;
+ int ret;
+ int len;
+ int i;
+
+ /*
+ * The closest value the HW supports is only one in fusion mode,
+ * and it is autoselected, so don't do anything, just return OK,
+ * as the closest possible value has been (virtually) selected
+ */
+ if (priv->operation_mode != BNO055_OPR_MODE_AMG)
+ return 0;
+
+ len = attr->len;
+
+ /*
+ * We always get a request in INT_PLUS_MICRO, but we
+ * take care of the micro part only when we really have
+ * non-integer tables. This prevents 32-bit overflow with
+ * larger integers contained in integer tables.
+ */
+ req_val = val;
+ if (attr->type != IIO_VAL_INT) {
+ if (val > 2147)
+ val = 2147;
+ len /= 2;
+ req_val = val * 1000000 + val2;
+ }
+
+ first = true;
+ for (i = 0; i < len; i++) {
+ switch (attr->type) {
+ case IIO_VAL_INT:
+ tbl_val = attr->vals[i];
+ break;
+ case IIO_VAL_INT_PLUS_MICRO:
+ WARN_ON(attr->vals[i * 2] > 2147);
+ tbl_val = attr->vals[i * 2] * 1000000 +
+ attr->vals[i * 2 + 1];
+ break;
+ case IIO_VAL_FRACTIONAL:
+ WARN_ON(attr->vals[i * 2] > 4294);
+ tbl_val = attr->vals[i * 2] * 1000000 /
+ attr->vals[i * 2 + 1];
+ break;
+ default:
+ return -EINVAL;
+ }
+ delta = abs(tbl_val - req_val);
+ if (first || delta < best_delta) {
+ best_delta = delta;
+ hwval = i;
+ first = false;
+ }
+ }
+
+ if (attr->hw_xlate)
+ hwval = attr->hw_xlate[hwval];
+
+ ret = bno055_operation_mode_do_set(priv, BNO055_OPR_MODE_CONFIG);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(priv->regmap, reg, mask, hwval << shift);
+ if (ret)
+ return ret;
+
+ return bno055_operation_mode_do_set(priv, BNO055_OPR_MODE_AMG);
+}
+
+static int bno055_read_simple_chan(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ struct bno055_priv *priv = iio_priv(indio_dev);
+ __le16 raw_val;
+ int ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ ret = regmap_bulk_read(priv->regmap, chan->address,
+ &raw_val, sizeof(raw_val));
+ if (ret < 0)
+ return ret;
+ *val = (s16)le16_to_cpu(raw_val);
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_OFFSET:
+ if (priv->operation_mode != BNO055_OPR_MODE_AMG) {
+ *val = 0;
+ } else {
+ ret = regmap_bulk_read(priv->regmap,
+ chan->address +
+ BNO055_REG_OFFSET_ADDR,
+ &raw_val, sizeof(raw_val));
+ if (ret < 0)
+ return ret;
+ /*
+ * IMU reports sensor offests; IIO wants correction
+ * offset, thus we need the 'minus' here.
+ */
+ *val = -(s16)le16_to_cpu(raw_val);
+ }
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_SCALE:
+ *val = 1;
+ switch (chan->type) {
+ case IIO_GRAVITY:
+ /* Table 3-35: 1 m/s^2 = 100 LSB */
+ case IIO_ACCEL:
+ /* Table 3-17: 1 m/s^2 = 100 LSB */
+ *val2 = 100;
+ break;
+ case IIO_MAGN:
+ /*
+ * Table 3-19: 1 uT = 16 LSB. But we need
+ * Gauss: 1G = 0.1 uT.
+ */
+ *val2 = 160;
+ break;
+ case IIO_ANGL_VEL:
+ /*
+ * Table 3-22: 1 Rps = 900 LSB
+ * .. but this is not exactly true. See comment at the
+ * beginning of this file.
+ */
+ if (priv->operation_mode != BNO055_OPR_MODE_AMG) {
+ *val = bno055_gyr_scale.fusion_vals[0];
+ *val2 = bno055_gyr_scale.fusion_vals[1];
+ return IIO_VAL_FRACTIONAL;
+ }
+
+ return bno055_get_regmask(priv, val, val2,
+ BNO055_GYR_CONFIG_REG,
+ BNO055_GYR_CONFIG_RANGE_MASK,
+ &bno055_gyr_scale);
+ break;
+ case IIO_ROT:
+ /* Table 3-28: 1 degree = 16 LSB */
+ *val2 = 16;
+ break;
+ default:
+ return -EINVAL;
+ }
+ return IIO_VAL_FRACTIONAL;
+
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ if (chan->type != IIO_MAGN)
+ return -EINVAL;
+ else
+ return bno055_get_regmask(priv, val, val2,
+ BNO055_MAG_CONFIG_REG,
+ BNO055_MAG_CONFIG_ODR_MASK,
+ &bno055_mag_odr);
+
+ case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
+ switch (chan->type) {
+ case IIO_ANGL_VEL:
+ return bno055_get_regmask(priv, val, val2,
+ BNO055_GYR_CONFIG_REG,
+ BNO055_GYR_CONFIG_LPF_MASK,
+ &bno055_gyr_lpf);
+ case IIO_ACCEL:
+ return bno055_get_regmask(priv, val, val2,
+ BNO055_ACC_CONFIG_REG,
+ BNO055_ACC_CONFIG_LPF_MASK,
+ &bno055_acc_lpf);
+ default:
+ return -EINVAL;
+ }
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static int bno055_sysfs_attr_avail(struct bno055_priv *priv, struct bno055_sysfs_attr *attr,
+ const int **vals, int *length)
+{
+ if (priv->operation_mode != BNO055_OPR_MODE_AMG) {
+ /* locked when fusion enabled */
+ *vals = attr->fusion_vals;
+ if (attr->type == IIO_VAL_INT)
+ *length = 1;
+ else
+ *length = 2; /* IIO_VAL_INT_PLUS_MICRO or IIO_VAL_FRACTIONAL*/
+ } else {
+ *vals = attr->vals;
+ *length = attr->len;
+ }
+
+ return attr->type;
+}
+
+static int bno055_read_avail(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ const int **vals, int *type, int *length,
+ long mask)
+{
+ struct bno055_priv *priv = iio_priv(indio_dev);
+
+ switch (mask) {
+ case IIO_CHAN_INFO_SCALE:
+ switch (chan->type) {
+ case IIO_ANGL_VEL:
+ *type = bno055_sysfs_attr_avail(priv, &bno055_gyr_scale,
+ vals, length);
+ return IIO_AVAIL_LIST;
+ default:
+ return -EINVAL;
+ }
+ case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
+ switch (chan->type) {
+ case IIO_ANGL_VEL:
+ *type = bno055_sysfs_attr_avail(priv, &bno055_gyr_lpf,
+ vals, length);
+ return IIO_AVAIL_LIST;
+ case IIO_ACCEL:
+ *type = bno055_sysfs_attr_avail(priv, &bno055_acc_lpf,
+ vals, length);
+ return IIO_AVAIL_LIST;
+ default:
+ return -EINVAL;
+ }
+
+ break;
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ switch (chan->type) {
+ case IIO_MAGN:
+ *type = bno055_sysfs_attr_avail(priv, &bno055_mag_odr,
+ vals, length);
+ return IIO_AVAIL_LIST;
+ default:
+ return -EINVAL;
+ }
+ default:
+ return -EINVAL;
+ }
+}
+
+static int bno055_read_temp_chan(struct iio_dev *indio_dev, int *val)
+{
+ struct bno055_priv *priv = iio_priv(indio_dev);
+ unsigned int raw_val;
+ int ret;
+
+ ret = regmap_read(priv->regmap, BNO055_TEMP_REG, &raw_val);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Tables 3-36 and 3-37: one byte of priv, signed, 1 LSB = 1C.
+ * ABI wants milliC.
+ */
+ *val = raw_val * 1000;
+
+ return IIO_VAL_INT;
+}
+
+static int bno055_read_quaternion(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int size, int *vals, int *val_len,
+ long mask)
+{
+ struct bno055_priv *priv = iio_priv(indio_dev);
+ __le16 raw_vals[4];
+ int i, ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ if (size < 4)
+ return -EINVAL;
+ ret = regmap_bulk_read(priv->regmap,
+ BNO055_QUAT_DATA_W_LSB_REG,
+ raw_vals, sizeof(raw_vals));
+ if (ret < 0)
+ return ret;
+ for (i = 0; i < 4; i++)
+ vals[i] = (s16)le16_to_cpu(raw_vals[i]);
+ *val_len = 4;
+ return IIO_VAL_INT_MULTIPLE;
+ case IIO_CHAN_INFO_SCALE:
+ /* Table 3-31: 1 quaternion = 2^14 LSB */
+ if (size < 2)
+ return -EINVAL;
+ vals[0] = 14;
+ vals[1] = 1 << 14;
+ return IIO_VAL_FRACTIONAL_LOG2;
+ default:
+ return -EINVAL;
+ }
+}
+
+static bool bno055_is_chan_readable(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan)
+{
+ struct bno055_priv *priv = iio_priv(indio_dev);
+
+ if (priv->operation_mode != BNO055_OPR_MODE_AMG)
+ return true;
+
+ switch (chan->type) {
+ case IIO_GRAVITY:
+ case IIO_ROT:
+ return false;
+ case IIO_ACCEL:
+ if (chan->channel2 == IIO_MOD_LINEAR_X ||
+ chan->channel2 == IIO_MOD_LINEAR_Y ||
+ chan->channel2 == IIO_MOD_LINEAR_Z)
+ return false;
+ return true;
+ default:
+ return true;
+ }
+}
+
+static int _bno055_read_raw_multi(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int size, int *vals, int *val_len,
+ long mask)
+{
+ if (!bno055_is_chan_readable(indio_dev, chan))
+ return -EBUSY;
+
+ switch (chan->type) {
+ case IIO_MAGN:
+ case IIO_ACCEL:
+ case IIO_ANGL_VEL:
+ case IIO_GRAVITY:
+ if (size < 2)
+ return -EINVAL;
+ *val_len = 2;
+ return bno055_read_simple_chan(indio_dev, chan,
+ &vals[0], &vals[1],
+ mask);
+ case IIO_TEMP:
+ *val_len = 1;
+ return bno055_read_temp_chan(indio_dev, &vals[0]);
+ case IIO_ROT:
+ /*
+ * Rotation is exposed as either a quaternion or three
+ * Euler angles.
+ */
+ if (chan->channel2 == IIO_MOD_QUATERNION)
+ return bno055_read_quaternion(indio_dev, chan,
+ size, vals,
+ val_len, mask);
+ if (size < 2)
+ return -EINVAL;
+ *val_len = 2;
+ return bno055_read_simple_chan(indio_dev, chan,
+ &vals[0], &vals[1],
+ mask);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int bno055_read_raw_multi(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int size, int *vals, int *val_len,
+ long mask)
+{
+ struct bno055_priv *priv = iio_priv(indio_dev);
+ int ret;
+
+ mutex_lock(&priv->lock);
+ ret = _bno055_read_raw_multi(indio_dev, chan, size,
+ vals, val_len, mask);
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static int _bno055_write_raw(struct iio_dev *iio_dev,
+ struct iio_chan_spec const *chan,
+ int val, int val2, long mask)
+{
+ struct bno055_priv *priv = iio_priv(iio_dev);
+
+ switch (chan->type) {
+ case IIO_MAGN:
+ switch (mask) {
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ return bno055_set_regmask(priv, val, val2,
+ BNO055_MAG_CONFIG_REG,
+ BNO055_MAG_CONFIG_ODR_MASK,
+ &bno055_mag_odr);
+ default:
+ return -EINVAL;
+ }
+ case IIO_ACCEL:
+ switch (mask) {
+ case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
+ return bno055_set_regmask(priv, val, val2,
+ BNO055_ACC_CONFIG_REG,
+ BNO055_ACC_CONFIG_LPF_MASK,
+ &bno055_acc_lpf);
+
+ default:
+ return -EINVAL;
+ }
+ case IIO_ANGL_VEL:
+ switch (mask) {
+ case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY:
+ return bno055_set_regmask(priv, val, val2,
+ BNO055_GYR_CONFIG_REG,
+ BNO055_GYR_CONFIG_LPF_MASK,
+ &bno055_gyr_lpf);
+ case IIO_CHAN_INFO_SCALE:
+ return bno055_set_regmask(priv, val, val2,
+ BNO055_GYR_CONFIG_REG,
+ BNO055_GYR_CONFIG_RANGE_MASK,
+ &bno055_gyr_scale);
+ default:
+ return -EINVAL;
+ }
+ default:
+ return -EINVAL;
+ }
+}
+
+static int bno055_write_raw(struct iio_dev *iio_dev,
+ struct iio_chan_spec const *chan,
+ int val, int val2, long mask)
+{
+ struct bno055_priv *priv = iio_priv(iio_dev);
+ int ret;
+
+ mutex_lock(&priv->lock);
+ ret = _bno055_write_raw(iio_dev, chan, val, val2, mask);
+ mutex_unlock(&priv->lock);
+
+ return ret;
+}
+
+static ssize_t in_accel_range_raw_available_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct bno055_priv *priv = iio_priv(dev_to_iio_dev(dev));
+ int len = 0;
+ int i;
+
+ if (priv->operation_mode != BNO055_OPR_MODE_AMG)
+ return sysfs_emit(buf, "%d\n", bno055_acc_range.fusion_vals[0]);
+
+ for (i = 0; i < bno055_acc_range.len; i++)
+ len += sysfs_emit_at(buf, len, "%d%c", bno055_acc_range.vals[i],
+ (i == bno055_acc_range.len - 1) ? '\n' : ' ');
+ return len;
+}
+
+static ssize_t bno055_fusion_enable_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct bno055_priv *priv = iio_priv(dev_to_iio_dev(dev));
+
+ return sysfs_emit(buf, "%d\n",
+ priv->operation_mode != BNO055_OPR_MODE_AMG);
+}
+
+static ssize_t bno055_fusion_enable_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t len)
+{
+ struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+ struct bno055_priv *priv = iio_priv(indio_dev);
+ int ret = 0;
+
+ if (indio_dev->active_scan_mask &&
+ !bitmap_empty(indio_dev->active_scan_mask, _BNO055_SCAN_MAX))
+ return -EBUSY;
+
+ if (sysfs_streq(buf, "0")) {
+ ret = bno055_operation_mode_set(priv, BNO055_OPR_MODE_AMG);
+ } else {
+ /*
+ * Coming from AMG means the FMC was off, just switch to fusion
+ * but don't change anything that doesn't belong to us (i.e let
+ * FMC stay off.
+ * Coming from any other fusion mode means we don't need to do
+ * anything.
+ */
+ if (priv->operation_mode == BNO055_OPR_MODE_AMG)
+ ret = bno055_operation_mode_set(priv, BNO055_OPR_MODE_FUSION_FMC_OFF);
+ }
+ if (ret)
+ return ret;
+ return len;
+}
+
+static ssize_t bno055_fmc_enable_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct bno055_priv *priv = iio_priv(dev_to_iio_dev(dev));
+
+ return sysfs_emit(buf, "%d\n",
+ priv->operation_mode == BNO055_OPR_MODE_FUSION);
+}
+
+static ssize_t bno055_fmc_enable_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t len)
+{
+ struct iio_dev *indio_dev = dev_to_iio_dev(dev);
+ struct bno055_priv *priv = iio_priv(indio_dev);
+ int ret;
+
+ if (indio_dev->active_scan_mask &&
+ !bitmap_empty(indio_dev->active_scan_mask, _BNO055_SCAN_MAX))
+ return -EBUSY;
+
+ if (sysfs_streq(buf, "0")) {
+ if (priv->operation_mode == BNO055_OPR_MODE_FUSION) {
+ ret = bno055_operation_mode_set(priv, BNO055_OPR_MODE_FUSION_FMC_OFF);
+ if (ret)
+ return ret;
+ }
+ } else {
+ if (priv->operation_mode == BNO055_OPR_MODE_AMG)
+ return -EINVAL;
+
+ if (priv->operation_mode != BNO055_OPR_MODE_FUSION) {
+ ret = bno055_operation_mode_set(priv, BNO055_OPR_MODE_FUSION);
+ if (ret)
+ return ret;
+ }
+ }
+
+ return len;
+}
+
+static ssize_t bno055_in_accel_range_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct bno055_priv *priv = iio_priv(dev_to_iio_dev(dev));
+ int val;
+ int ret;
+
+ ret = bno055_get_regmask(priv, &val, NULL,
+ BNO055_ACC_CONFIG_REG,
+ BNO055_ACC_CONFIG_RANGE_MASK,
+ &bno055_acc_range);
+ if (ret < 0)
+ return ret;
+
+ return sysfs_emit(buf, "%d\n", val);
+}
+
+static ssize_t bno055_in_accel_range_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t len)
+{
+ struct bno055_priv *priv = iio_priv(dev_to_iio_dev(dev));
+ unsigned long val;
+ int ret;
+
+ ret = kstrtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ mutex_lock(&priv->lock);
+ ret = bno055_set_regmask(priv, val, 0,
+ BNO055_ACC_CONFIG_REG,
+ BNO055_ACC_CONFIG_RANGE_MASK,
+ &bno055_acc_range);
+ mutex_unlock(&priv->lock);
+
+ return ret ?: len;
+}
+
+static ssize_t bno055_get_calib_status(struct device *dev, char *buf, int which)
+{
+ struct bno055_priv *priv = iio_priv(dev_to_iio_dev(dev));
+ int calib;
+ int ret;
+ int val;
+
+ if (priv->operation_mode == BNO055_OPR_MODE_AMG ||
+ (priv->operation_mode == BNO055_OPR_MODE_FUSION_FMC_OFF &&
+ which == BNO055_CALIB_STAT_MAGN_SHIFT)) {
+ calib = 0;
+ } else {
+ mutex_lock(&priv->lock);
+ ret = regmap_read(priv->regmap, BNO055_CALIB_STAT_REG, &val);
+ mutex_unlock(&priv->lock);
+
+ if (ret)
+ return -EIO;
+
+ calib = ((val >> which) & BNO055_CALIB_STAT_MASK) + 1;
+ }
+
+ return sysfs_emit(buf, "%d\n", calib);
+}
+
+static ssize_t serial_number_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct bno055_priv *priv = iio_priv(dev_to_iio_dev(dev));
+
+ return sysfs_emit(buf, "%*ph\n", BNO055_UID_LEN, priv->uid);
+}
+
+static ssize_t calibration_data_read(struct file *filp, struct kobject *kobj,
+ struct bin_attribute *bin_attr, char *buf,
+ loff_t pos, size_t count)
+{
+ struct bno055_priv *priv = iio_priv(dev_to_iio_dev(kobj_to_dev(kobj)));
+ u8 data[BNO055_CALDATA_LEN];
+ int ret;
+
+ /*
+ * Calibration data is volatile; reading it in chunks will possibly
+ * results in inconsistent data. We require the user to read the whole
+ * blob in a single chunk
+ */
+ if (count < BNO055_CALDATA_LEN || pos != 0)
+ return -EINVAL;
+
+ mutex_lock(&priv->lock);
+ ret = bno055_operation_mode_do_set(priv, BNO055_OPR_MODE_CONFIG);
+ if (ret)
+ goto unlock;
+
+ ret = regmap_bulk_read(priv->regmap, BNO055_CALDATA_START, data,
+ BNO055_CALDATA_LEN);
+ if (ret)
+ goto unlock;
+
+ ret = bno055_operation_mode_do_set(priv, priv->operation_mode);
+ if (ret)
+ goto unlock;
+
+ memcpy(buf, data, BNO055_CALDATA_LEN);
+
+ ret = BNO055_CALDATA_LEN;
+unlock:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static ssize_t sys_calibration_auto_status_show(struct device *dev,
+ struct device_attribute *a,
+ char *buf)
+{
+ return bno055_get_calib_status(dev, buf, BNO055_CALIB_STAT_SYS_SHIFT);
+}
+
+static ssize_t in_accel_calibration_auto_status_show(struct device *dev,
+ struct device_attribute *a,
+ char *buf)
+{
+ return bno055_get_calib_status(dev, buf, BNO055_CALIB_STAT_ACCEL_SHIFT);
+}
+
+static ssize_t in_gyro_calibration_auto_status_show(struct device *dev,
+ struct device_attribute *a,
+ char *buf)
+{
+ return bno055_get_calib_status(dev, buf, BNO055_CALIB_STAT_GYRO_SHIFT);
+}
+
+static ssize_t in_magn_calibration_auto_status_show(struct device *dev,
+ struct device_attribute *a,
+ char *buf)
+{
+ return bno055_get_calib_status(dev, buf, BNO055_CALIB_STAT_MAGN_SHIFT);
+}
+
+#ifdef CONFIG_DEBUG_FS
+static int bno055_debugfs_reg_access(struct iio_dev *iio_dev, unsigned int reg,
+ unsigned int writeval, unsigned int *readval)
+{
+ struct bno055_priv *priv = iio_priv(iio_dev);
+
+ if (readval)
+ return regmap_read(priv->regmap, reg, readval);
+ else
+ return regmap_write(priv->regmap, reg, writeval);
+}
+
+static ssize_t bno055_show_fw_version(struct file *file, char __user *userbuf,
+ size_t count, loff_t *ppos)
+{
+ struct bno055_priv *priv = file->private_data;
+ int rev, ver;
+ char *buf;
+ int ret;
+
+ ret = regmap_read(priv->regmap, BNO055_SW_REV_LSB_REG, &rev);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(priv->regmap, BNO055_SW_REV_MSB_REG, &ver);
+ if (ret)
+ return ret;
+
+ buf = kasprintf(GFP_KERNEL, "ver: 0x%x, rev: 0x%x\n", ver, rev);
+ if (!buf)
+ return -ENOMEM;
+
+ ret = simple_read_from_buffer(userbuf, count, ppos, buf, strlen(buf));
+ kfree(buf);
+
+ return ret;
+}
+
+static const struct file_operations bno055_fw_version_ops = {
+ .open = simple_open,
+ .read = bno055_show_fw_version,
+ .llseek = default_llseek,
+ .owner = THIS_MODULE,
+};
+
+static void bno055_debugfs_remove(void *debugfs)
+{
+ debugfs_remove((struct dentry *)debugfs);
+}
+
+static void bno055_debugfs_init(struct iio_dev *iio_dev)
+{
+ struct bno055_priv *priv = iio_priv(iio_dev);
+
+ priv->debugfs = debugfs_create_file("firmware_version", 0400,
+ iio_get_debugfs_dentry(iio_dev),
+ priv, &bno055_fw_version_ops);
+
+ devm_add_action_or_reset(priv->dev, bno055_debugfs_remove, priv->debugfs);
+}
+#else
+static void bno055_debugfs_init(struct iio_dev *iio_dev)
+{
+}
+
+int bno055_debugfs_reg_access(struct iio_dev *iio_dev, unsigned int reg,
+ unsigned int writeval, unsigned int *readval)
+{
+ return 0;
+}
+#endif
+
+static IIO_DEVICE_ATTR(fusion_enable, 0644,
+ bno055_fusion_enable_show,
+ bno055_fusion_enable_store, 0);
+
+static IIO_DEVICE_ATTR(in_magn_calibration_fast_enable, 0644,
+ bno055_fmc_enable_show,
+ bno055_fmc_enable_store, 0);
+
+static IIO_DEVICE_ATTR(in_accel_range_raw, 0644,
+ bno055_in_accel_range_show,
+ bno055_in_accel_range_store, 0);
+
+static IIO_DEVICE_ATTR_RO(in_accel_range_raw_available, 0);
+
+static IIO_DEVICE_ATTR_RO(sys_calibration_auto_status, 0);
+static IIO_DEVICE_ATTR_RO(in_accel_calibration_auto_status, 0);
+static IIO_DEVICE_ATTR_RO(in_gyro_calibration_auto_status, 0);
+static IIO_DEVICE_ATTR_RO(in_magn_calibration_auto_status, 0);
+
+static IIO_DEVICE_ATTR_RO(serial_number, 0);
+
+static struct attribute *bno055_attrs[] = {
+ &iio_dev_attr_in_accel_range_raw_available.dev_attr.attr,
+ &iio_dev_attr_in_accel_range_raw.dev_attr.attr,
+ &iio_dev_attr_fusion_enable.dev_attr.attr,
+ &iio_dev_attr_in_magn_calibration_fast_enable.dev_attr.attr,
+ &iio_dev_attr_sys_calibration_auto_status.dev_attr.attr,
+ &iio_dev_attr_in_accel_calibration_auto_status.dev_attr.attr,
+ &iio_dev_attr_in_gyro_calibration_auto_status.dev_attr.attr,
+ &iio_dev_attr_in_magn_calibration_auto_status.dev_attr.attr,
+ &iio_dev_attr_serial_number.dev_attr.attr,
+ NULL
+};
+
+static BIN_ATTR_RO(calibration_data, BNO055_CALDATA_LEN);
+
+static struct bin_attribute *bno055_bin_attrs[] = {
+ &bin_attr_calibration_data,
+ NULL
+};
+
+static const struct attribute_group bno055_attrs_group = {
+ .attrs = bno055_attrs,
+ .bin_attrs = bno055_bin_attrs,
+};
+
+static const struct iio_info bno055_info = {
+ .read_raw_multi = bno055_read_raw_multi,
+ .read_avail = bno055_read_avail,
+ .write_raw = bno055_write_raw,
+ .attrs = &bno055_attrs_group,
+ .debugfs_reg_access = bno055_debugfs_reg_access,
+};
+
+/*
+ * Reads len samples from the HW, stores them in buf starting from buf_idx,
+ * and applies mask to cull (skip) unneeded samples.
+ * Updates buf_idx incrementing with the number of stored samples.
+ * Samples from HW are transferred into buf, then in-place copy on buf is
+ * performed in order to cull samples that need to be skipped.
+ * This avoids copies of the first samples until we hit the 1st sample to skip,
+ * and also avoids having an extra bounce buffer.
+ * buf must be able to contain len elements in spite of how many samples we are
+ * going to cull.
+ */
+static int bno055_scan_xfer(struct bno055_priv *priv,
+ int start_ch, int len, unsigned long mask,
+ __le16 *buf, int *buf_idx)
+{
+ const int base = BNO055_ACC_DATA_X_LSB_REG;
+ bool quat_in_read = false;
+ int buf_base = *buf_idx;
+ __le16 *dst, *src;
+ int offs_fixup = 0;
+ int xfer_len = len;
+ int ret;
+ int i, n;
+
+ if (!mask)
+ return 0;
+
+ /*
+ * All chans are made up 1 16-bit sample, except for quaternion that is
+ * made up 4 16-bit values.
+ * For us the quaternion CH is just like 4 regular CHs.
+ * If our read starts past the quaternion make sure to adjust the
+ * starting offset; if the quaternion is contained in our scan then make
+ * sure to adjust the read len.
+ */
+ if (start_ch > BNO055_SCAN_QUATERNION) {
+ start_ch += 3;
+ } else if ((start_ch <= BNO055_SCAN_QUATERNION) &&
+ ((start_ch + len) > BNO055_SCAN_QUATERNION)) {
+ quat_in_read = true;
+ xfer_len += 3;
+ }
+
+ ret = regmap_bulk_read(priv->regmap,
+ base + start_ch * sizeof(__le16),
+ buf + buf_base,
+ xfer_len * sizeof(__le16));
+ if (ret)
+ return ret;
+
+ for_each_set_bit(i, &mask, len) {
+ if (quat_in_read && ((start_ch + i) > BNO055_SCAN_QUATERNION))
+ offs_fixup = 3;
+
+ dst = buf + *buf_idx;
+ src = buf + buf_base + offs_fixup + i;
+
+ n = (start_ch + i == BNO055_SCAN_QUATERNION) ? 4 : 1;
+
+ if (dst != src)
+ memcpy(dst, src, n * sizeof(__le16));
+
+ *buf_idx += n;
+ }
+ return 0;
+}
+
+static irqreturn_t bno055_trigger_handler(int irq, void *p)
+{
+ struct iio_poll_func *pf = p;
+ struct iio_dev *iio_dev = pf->indio_dev;
+ struct bno055_priv *priv = iio_priv(iio_dev);
+ int xfer_start, start, end, prev_end;
+ unsigned long mask;
+ int quat_extra_len;
+ bool first = true;
+ int buf_idx = 0;
+ bool thr_hit;
+ int ret;
+
+ mutex_lock(&priv->lock);
+
+ /*
+ * Walk the bitmap and eventually perform several transfers.
+ * Bitmap ones-fileds that are separated by gaps <= xfer_burst_break_thr
+ * will be included in same transfer.
+ * Every time the bitmap contains a gap wider than xfer_burst_break_thr
+ * then we split the transfer, skipping the gap.
+ */
+ for_each_set_bitrange(start, end, iio_dev->active_scan_mask,
+ iio_dev->masklength) {
+ /*
+ * First transfer will start from the beginnig of the first
+ * ones-field in the bitmap
+ */
+ if (first)
+ xfer_start = start;
+
+ /*
+ * We found the next ones-field; check whether to include it in
+ * the current transfer or not (i.e. let's perform the current
+ * transfer and prepare for another one).
+ */
+ if (!first) {
+ /*
+ * In case the zeros-gap contains the quaternion bit,
+ * then its length is actually 4 words instead of 1
+ * (i.e. +3 wrt other channels).
+ */
+ quat_extra_len = ((start > BNO055_SCAN_QUATERNION) &&
+ (prev_end <= BNO055_SCAN_QUATERNION)) ? 3 : 0;
+
+ /* If the gap is wider than xfer_burst_break_thr then.. */
+ thr_hit = (start - prev_end + quat_extra_len) >
+ priv->xfer_burst_break_thr;
+
+ /*
+ * .. transfer all the data up to the gap. Then set the
+ * next transfer start index at right after the gap
+ * (i.e. at the start of this ones-field).
+ */
+ if (thr_hit) {
+ mask = *iio_dev->active_scan_mask >> xfer_start;
+ ret = bno055_scan_xfer(priv, xfer_start,
+ prev_end - xfer_start,
+ mask, priv->buf.chans, &buf_idx);
+ if (ret)
+ goto done;
+ xfer_start = start;
+ }
+ }
+ first = false;
+ prev_end = end;
+ }
+
+ /*
+ * We finished walking the bitmap; no more gaps to check for. Just
+ * perform the current transfer.
+ */
+ mask = *iio_dev->active_scan_mask >> xfer_start;
+ ret = bno055_scan_xfer(priv, xfer_start,
+ prev_end - xfer_start,
+ mask, priv->buf.chans, &buf_idx);
+
+ iio_push_to_buffers_with_timestamp(iio_dev, &priv->buf, pf->timestamp);
+done:
+ mutex_unlock(&priv->lock);
+ iio_trigger_notify_done(iio_dev->trig);
+ return IRQ_HANDLED;
+}
+
+static int bno055_buffer_preenable(struct iio_dev *indio_dev)
+{
+ struct bno055_priv *priv = iio_priv(indio_dev);
+ const unsigned long fusion_mask =
+ BIT(BNO055_SCAN_YAW) |
+ BIT(BNO055_SCAN_ROLL) |
+ BIT(BNO055_SCAN_PITCH) |
+ BIT(BNO055_SCAN_QUATERNION) |
+ BIT(BNO055_SCAN_LIA_X) |
+ BIT(BNO055_SCAN_LIA_Y) |
+ BIT(BNO055_SCAN_LIA_Z) |
+ BIT(BNO055_SCAN_GRAVITY_X) |
+ BIT(BNO055_SCAN_GRAVITY_Y) |
+ BIT(BNO055_SCAN_GRAVITY_Z);
+
+ if (priv->operation_mode == BNO055_OPR_MODE_AMG &&
+ bitmap_intersects(indio_dev->active_scan_mask, &fusion_mask,
+ _BNO055_SCAN_MAX))
+ return -EBUSY;
+ return 0;
+}
+
+static const struct iio_buffer_setup_ops bno055_buffer_setup_ops = {
+ .preenable = bno055_buffer_preenable,
+};
+
+static void bno055_clk_disable(void *arg)
+{
+ clk_disable_unprepare((struct clk *)arg);
+}
+
+int bno055_probe(struct device *dev, struct regmap *regmap,
+ int xfer_burst_break_thr, bool sw_reset)
+{
+ const struct firmware *caldata;
+ struct bno055_priv *priv;
+ const u8 *caldata_data = NULL;
+ struct iio_dev *iio_dev;
+ int caldata_size = 0;
+ char *fw_name_buf;
+ unsigned int val;
+ int rev, ver;
+ int ret;
+
+ iio_dev = devm_iio_device_alloc(dev, sizeof(*priv));
+ if (!iio_dev)
+ return -ENOMEM;
+
+ iio_dev->name = "bno055";
+ priv = iio_priv(iio_dev);
+ mutex_init(&priv->lock);
+ priv->regmap = regmap;
+ priv->dev = dev;
+ priv->xfer_burst_break_thr = xfer_burst_break_thr;
+ priv->sw_reset = sw_reset;
+
+ priv->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(priv->reset_gpio))
+ return dev_err_probe(dev, PTR_ERR(priv->reset_gpio), "Failed to get reset GPIO");
+
+ priv->clk = devm_clk_get_optional(dev, "clk");
+ if (IS_ERR(priv->clk))
+ return dev_err_probe(dev, PTR_ERR(priv->clk), "Failed to get CLK");
+
+ ret = clk_prepare_enable(priv->clk);
+ if (ret)
+ return ret;
+
+ ret = devm_add_action_or_reset(dev, bno055_clk_disable, priv->clk);
+ if (ret)
+ return ret;
+
+ if (priv->reset_gpio) {
+ usleep_range(5000, 10000);
+ gpiod_set_value_cansleep(priv->reset_gpio, 1);
+ usleep_range(650000, 750000);
+ } else {
+ if (!sw_reset)
+ dev_warn(dev, "No usable reset method; IMU may be unreliable");
+ }
+
+ ret = regmap_read(priv->regmap, BNO055_CHIP_ID_REG, &val);
+ if (ret)
+ return ret;
+
+ if (val != BNO055_CHIP_ID_MAGIC) {
+ dev_err(dev, "Unrecognized chip ID 0x%x", val);
+ return -ENODEV;
+ }
+
+ /*
+ * In case we haven't a HW reset pin, we can still reset the chip via
+ * register write. This is probably nonsense in case we can't even
+ * communicate with the chip or the chip isn't the one we expect (i.e.
+ * we don't write to unknown chips), so we perform SW reset only after
+ * chip magic ID check
+ */
+ if (!priv->reset_gpio) {
+ ret = bno055_system_reset(priv);
+ if (ret)
+ return ret;
+ }
+
+ ret = regmap_read(priv->regmap, BNO055_SW_REV_LSB_REG, &rev);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(priv->regmap, BNO055_SW_REV_MSB_REG, &ver);
+ if (ret)
+ return ret;
+
+ /*
+ * Seems that stock FW version conains a bug (see comment at the
+ * beginning of this file) that causes the anglvel scale to be changed
+ * depending by the chip range setting. We workaround this, but we don't
+ * know what other FW version might do..
+ */
+ if (ver != 0x3 || rev != 0x11)
+ dev_warn(dev, "Untested firmware version. Anglvel scale may not work as expected");
+
+ ret = regmap_bulk_read(priv->regmap, BNO055_UID_LOWER_REG,
+ priv->uid, BNO055_UID_LEN);
+ if (ret)
+ return ret;
+
+ /*
+ * This has nothing to do with the IMU firmware, this is for sensor
+ * calibration data.
+ */
+ fw_name_buf = kasprintf(GFP_KERNEL,
+ BNO055_FW_UID_NAME,
+ BNO055_UID_LEN, priv->uid);
+ if (!fw_name_buf)
+ return -ENOMEM;
+
+ ret = request_firmware(&caldata, fw_name_buf, dev);
+ kfree(fw_name_buf);
+ if (ret)
+ ret = request_firmware(&caldata, BNO055_FW_GENERIC_NAME, dev);
+
+ if (ret)
+ dev_notice(dev, "Calibration file load failed. See instruction in kernel Documentation/iio/bno055.rst");
+
+ if (caldata) {
+ caldata_data = caldata->data;
+ caldata_size = caldata->size;
+ }
+ ret = bno055_init(priv, caldata_data, caldata_size);
+ if (caldata)
+ release_firmware(caldata);
+ if (ret)
+ return ret;
+
+ priv->operation_mode = BNO055_OPR_MODE_FUSION;
+ ret = bno055_operation_mode_do_set(priv, priv->operation_mode);
+ if (ret)
+ return ret;
+
+ ret = devm_add_action_or_reset(dev, bno055_uninit, priv);
+ if (ret)
+ return ret;
+
+ iio_dev->channels = bno055_channels;
+ iio_dev->num_channels = ARRAY_SIZE(bno055_channels);
+ iio_dev->info = &bno055_info;
+ iio_dev->modes = INDIO_DIRECT_MODE;
+
+ ret = devm_iio_triggered_buffer_setup(dev, iio_dev,
+ iio_pollfunc_store_time,
+ bno055_trigger_handler,
+ &bno055_buffer_setup_ops);
+ if (ret)
+ return ret;
+
+ ret = devm_iio_device_register(dev, iio_dev);
+ if (ret)
+ return ret;
+
+ bno055_debugfs_init(iio_dev);
+
+ return 0;
+}
+EXPORT_SYMBOL_NS_GPL(bno055_probe, IIO_BNO055);
+
+MODULE_AUTHOR("Andrea Merello <[email protected]>");
+MODULE_DESCRIPTION("Bosch BNO055 driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/iio/imu/bno055/bno055.h b/drivers/iio/imu/bno055/bno055.h
new file mode 100644
index 000000000000..2ccb373c61cd
--- /dev/null
+++ b/drivers/iio/imu/bno055/bno055.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+#ifndef __BNO055_H__
+#define __BNO055_H__
+
+#include <linux/regmap.h>
+
+struct device;
+int bno055_probe(struct device *dev, struct regmap *regmap,
+ int xfer_burst_break_thr, bool sw_reset);
+extern const struct regmap_config bno055_regmap_config;
+
+#endif
--
2.17.1
From: Andrea Merello <[email protected]>
Signed-off-by: Andrea Merello <[email protected]>
---
tools/iio/iio_event_monitor.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/tools/iio/iio_event_monitor.c b/tools/iio/iio_event_monitor.c
index 2f4581658859..1fee44abb836 100644
--- a/tools/iio/iio_event_monitor.c
+++ b/tools/iio/iio_event_monitor.c
@@ -122,6 +122,9 @@ static const char * const iio_modifier_names[] = {
[IIO_MOD_PM4] = "pm4",
[IIO_MOD_PM10] = "pm10",
[IIO_MOD_O2] = "o2",
+ [IIO_MOD_LINEAR_X] = "linear_x",
+ [IIO_MOD_LINEAR_Y] = "linear_y",
+ [IIO_MOD_LINEAR_Z] = "linear_z",
};
static bool event_is_known(struct iio_event_data *event)
--
2.17.1
From: Andrea Merello <[email protected]>
This patch adds modifiers for reporting rotations as euler angles (i.e.
yaw, pitch and roll).
Signed-off-by: Andrea Merello <[email protected]>
---
drivers/iio/industrialio-core.c | 3 +++
include/uapi/linux/iio/types.h | 3 +++
2 files changed, 6 insertions(+)
diff --git a/drivers/iio/industrialio-core.c b/drivers/iio/industrialio-core.c
index d087b2607cc9..aa5f98d3b334 100644
--- a/drivers/iio/industrialio-core.c
+++ b/drivers/iio/industrialio-core.c
@@ -137,6 +137,9 @@ static const char * const iio_modifier_names[] = {
[IIO_MOD_LINEAR_X] = "linear_x",
[IIO_MOD_LINEAR_Y] = "linear_y",
[IIO_MOD_LINEAR_Z] = "linear_z",
+ [IIO_MOD_PITCH] = "pitch",
+ [IIO_MOD_YAW] = "yaw",
+ [IIO_MOD_ROLL] = "roll",
};
/* relies on pairs of these shared then separate */
diff --git a/include/uapi/linux/iio/types.h b/include/uapi/linux/iio/types.h
index 0993f6b697fc..4853701ba70d 100644
--- a/include/uapi/linux/iio/types.h
+++ b/include/uapi/linux/iio/types.h
@@ -98,6 +98,9 @@ enum iio_modifier {
IIO_MOD_LINEAR_X,
IIO_MOD_LINEAR_Y,
IIO_MOD_LINEAR_Z,
+ IIO_MOD_PITCH,
+ IIO_MOD_YAW,
+ IIO_MOD_ROLL,
};
enum iio_event_type {
--
2.17.1
From: Andrea Merello <[email protected]>
This patch adds ABI documentation for the new "serial_number" sysfs
attribute. The first user is the bno055 IIO driver.
Signed-off-by: Andrea Merello <[email protected]>
---
Documentation/ABI/testing/sysfs-bus-iio | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index 2a6954ea1c71..3be613f64843 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -2048,3 +2048,10 @@ Contact: [email protected]
Description:
Raw (unscaled) euler angles readings. Units after
application of scale are deg.
+
+What: /sys/bus/iio/devices/iio:deviceX/serial_number
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ An example format is 16-bytes, 2-digits-per-byte, HEX-string
+ representing the sensor unique ID number.
--
2.17.1
From: Andrea Merello <[email protected]>
This patch adds ABI documentation for bno055 driver private sysfs
attributes.
Signed-off-by: Andrea Merello <[email protected]>
---
.../ABI/testing/sysfs-bus-iio-bno055 | 81 +++++++++++++++++++
1 file changed, 81 insertions(+)
create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-bno055
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-bno055 b/Documentation/ABI/testing/sysfs-bus-iio-bno055
new file mode 100644
index 000000000000..22a5c6dc90dc
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-bno055
@@ -0,0 +1,81 @@
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_raw_range
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Raw (unscaled) range for acceleration readings. Unit after
+ application of scale is m/s^2. Note that this doesn't affects
+ the scale (which should be used when changing the maximum and
+ minimum readable value affects also the reading scaling factor).
+
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_raw_range
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Range for angular velocity readings in radians per second. Note
+ that this does not affects the scale (which should be used when
+ changing the maximum and minimum readable value affects also the
+ reading scaling factor).
+
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_raw_range_available
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ List of allowed values for in_accel_raw_range attribute
+
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_raw_range_available
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ List of allowed values for in_anglvel_raw_range attribute
+
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_calibration_fast_enable
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Can be 1 or 0. Enables/disables the "Fast Magnetometer
+ Calibration" HW function.
+
+What: /sys/bus/iio/devices/iio:deviceX/fusion_enable
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Can be 1 or 0. Enables/disables the "sensor fusion" (a.k.a.
+ NDOF) HW function.
+
+What: /sys/bus/iio/devices/iio:deviceX/calibration_data
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Reports the binary calibration data blob for the IMU sensors.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_calibration_auto_status
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Reports the autocalibration status for the accelerometer sensor.
+ Can be 0 (calibration non even enabled) or 1 to 5 where the greater
+ the number, the better the calibration status.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_gyro_calibration_auto_status
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Reports the autocalibration status for the gyroscope sensor.
+ Can be 0 (calibration non even enabled) or 1 to 5 where the greater
+ the number, the better the calibration status.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_calibration_auto_status
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Reports the autocalibration status for the magnetometer sensor.
+ Can be 0 (calibration non even enabled) or 1 to 5 where the greater
+ the number, the better the calibration status.
+
+What: /sys/bus/iio/devices/iio:deviceX/sys_calibration_auto_status
+KernelVersion: 5.19
+Contact: [email protected]
+Description:
+ Reports the status for the IMU overall autocalibration.
+ Can be 0 (calibration non even enabled) or 1 to 5 where the greater
+ the number, the better the calibration status.
--
2.17.1
On Fri, Apr 15, 2022 at 4:00 PM Andrea Merello <[email protected]> wrote:
>
> From: Andrea Merello <[email protected]>
Missed commit message.
> Signed-off-by: Andrea Merello <[email protected]>
--
With Best Regards,
Andy Shevchenko
On Fri, Apr 15, 2022 at 4:00 PM Andrea Merello <[email protected]> wrote:
>
> From: Andrea Merello <[email protected]>
>
> This series (tries to) add support for Bosch BNO055 IMU to Linux IIO
> subsystem. It is made up several patches:
>
> 1/13 to 7/12: add some IIO modifiers, and their documentation, to the IIO
> core layer, in order to being able to expose the linear
> acceleration and Euler angles among standard attributes.
> Also update the IIO event monitor tool
>
> 7/13: fix binary attributes didn't work with IIO
>
> 8/13 to 11/13: add the core IIO BNO055 driver and documentation for sysfs
> attributes and DT bindings
>
> 12/13: adds serdev BNO055 driver to actually use the IMU via serial line
>
> 13/13: adds I2C BNO055 driver to actually use the IMU via I2C wiring
>
> 14/13: add a documentation file that describe the bno055 driver and
> specifically the calibration
Thanks for a new version.
So far I have noticed the issues with more than one patch:
1) missed commit message;
2) non-imperative mode of speaking in the commit messages.
Please, take your time to refresh the Submitting Patches documentation
and fix your series accordingly.
--
With Best Regards,
Andy Shevchenko
On Fri, Apr 15, 2022 at 4:00 PM Andrea Merello <[email protected]> wrote:
>
> From: Andrea Merello <[email protected]>
>
> This patch adds modifiers for reporting rotations as euler angles (i.e.
> yaw, pitch and roll).
s/This patch adds/Add/
Please, read the Submitting Patches documentation where it explicitly tells.
--
With Best Regards,
Andy Shevchenko
On 4/15/22 15:00, Andrea Merello wrote:
> From: Andrea Merello <[email protected]>
>
> This patch adds ABI documentation for the new "serial_number" sysfs
> attribute. The first user is the bno055 IIO driver.
>
> Signed-off-by: Andrea Merello <[email protected]>
> ---
> Documentation/ABI/testing/sysfs-bus-iio | 7 +++++++
> 1 file changed, 7 insertions(+)
>
> diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
> index 2a6954ea1c71..3be613f64843 100644
> --- a/Documentation/ABI/testing/sysfs-bus-iio
> +++ b/Documentation/ABI/testing/sysfs-bus-iio
> @@ -2048,3 +2048,10 @@ Contact: [email protected]
> Description:
> Raw (unscaled) euler angles readings. Units after
> application of scale are deg.
> +
> +What: /sys/bus/iio/devices/iio:deviceX/serial_number
Can we make this `serialnumber`? IIO uses underscores to separate
different parts of the name and to a machine (e.g. libiio) serial_number
looks like a channel called serial with an attribute called number.
> +KernelVersion: 5.19
> +Contact: [email protected]
> +Description:
> + An example format is 16-bytes, 2-digits-per-byte, HEX-string
> + representing the sensor unique ID number.
On Tue, 19 Apr 2022 09:41:54 +0200
Lars-Peter Clausen <[email protected]> wrote:
> On 4/15/22 15:00, Andrea Merello wrote:
> > From: Andrea Merello <[email protected]>
> >
> > This patch adds ABI documentation for the new "serial_number" sysfs
> > attribute. The first user is the bno055 IIO driver.
> >
> > Signed-off-by: Andrea Merello <[email protected]>
> > ---
> > Documentation/ABI/testing/sysfs-bus-iio | 7 +++++++
> > 1 file changed, 7 insertions(+)
> >
> > diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
> > index 2a6954ea1c71..3be613f64843 100644
> > --- a/Documentation/ABI/testing/sysfs-bus-iio
> > +++ b/Documentation/ABI/testing/sysfs-bus-iio
> > @@ -2048,3 +2048,10 @@ Contact: [email protected]
> > Description:
> > Raw (unscaled) euler angles readings. Units after
> > application of scale are deg.
> > +
> > +What: /sys/bus/iio/devices/iio:deviceX/serial_number
>
> Can we make this `serialnumber`? IIO uses underscores to separate
> different parts of the name and to a machine (e.g. libiio) serial_number
> looks like a channel called serial with an attribute called number.
Works for me.
J
>
>
> > +KernelVersion: 5.19
> > +Contact: [email protected]
> > +Description:
> > + An example format is 16-bytes, 2-digits-per-byte, HEX-string
> > + representing the sensor unique ID number.
>
>