2023-09-29 09:19:20

by claudiu beznea

[permalink] [raw]
Subject: [PATCH v2 14/28] pinctrl: renesas: rzg2l: index all registers based on port offset

From: Claudiu Beznea <[email protected]>

To get address that needs to be read/write for specific port
functionalities the P(), PM(), PMC(), PFC(), PIN(), IOLH() IEN(), ISEL()
macros are used. Some of these macros received as argument the hardware
port identifier, some hardware port offset address (e.g. ISEL() received
port identifier, IOLH() received port offset address). This makes hard to
extend the current driver for SoCs were port identifiers are not continuous
in memory map of pin controller. This is the case for RZ/G3S pin controller
were ports are mapped as follows:

port offset port identifier
----------- ---------------
0x20 P0
0x21 P5
0x22 P6
0x23 P11
0x24 P12
0x25 P13
0x26 P14
0x27 P15
0x28 P16
0x29 P17
0x2a P18
0x30 P1
0x31 P2
0x32 P3
0x33 P4
0x34 P7
0x35 P8
0x36 P8
0x37 P10

To make this achievable change all the above macros used to get the address
of a port register for specific port functionality based on port hardware
address. Shortly, all the above macros will get as argument the port
offset address listed in the above table.

With this RZG2L_SINGLE_PIN_GET_PORT_OFFSET(), RZG2L_PIN_ID_TO_PORT_OFFSET()
and RZG2L_GPIO_PORT_GET_INDEX() were replaced by
RZG2L_PIN_CFG_TO_PORT_OFFSET(), RZG2L_SINGLE_PIN_GET_CFGS() and
RZG2L_GPIO_PORT_GET_CFGS() were replaced by RZG2L_PIN_CFG_TO_CAPS().

Also rzg2l_pinctrl_set_pfc_mode() don't need port argument anymore.
Also rzg2l_gpio_direction_input() and rzg2l_gpio_direction_output() don't
need to translate port and bit locally as this can be done by
rzg2l_gpio_set_direction().

To use the same naming for port, bit/pin and register offset the
port_offset variable names in different places was replaced by variable
named off and there is no need to initialize anymore cfg and bit in
different code places.

Signed-off-by: Claudiu Beznea <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Lad Prabhakar <[email protected]>
Tested-by: Lad Prabhakar <[email protected]>
---

Changes in v2:
- mentioned in commit description about the replacement of
RZG2L_GPIO_PORT_GET_INDEX() with RZG2L_PIN_CFG_TO_PORT_OFFSET()
- moved variable declaration inside for()
- got rid of local variable and used directly RZG2L_PIN_ID_TO_PORT() in
debug message from rzg2l_pinctrl_set_mux() function
- collected tags

drivers/pinctrl/renesas/pinctrl-rzg2l.c | 183 ++++++++++++------------
1 file changed, 95 insertions(+), 88 deletions(-)

diff --git a/drivers/pinctrl/renesas/pinctrl-rzg2l.c b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
index 03b36c6b2b6d..96fd829131bd 100644
--- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
+++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
@@ -74,8 +74,6 @@
*/
#define RZG2L_GPIO_PORT_PACK(n, a, f) (((n) << 28) | ((a) << 20) | (f))
#define RZG2L_GPIO_PORT_GET_PINCNT(x) (((x) & GENMASK(30, 28)) >> 28)
-#define RZG2L_GPIO_PORT_GET_INDEX(x) (((x) & GENMASK(26, 20)) >> 20)
-#define RZG2L_GPIO_PORT_GET_CFGS(x) ((x) & GENMASK(19, 0))

/*
* BIT(31) indicates dedicated pin, p is the register index while
@@ -85,18 +83,21 @@
#define RZG2L_SINGLE_PIN BIT(31)
#define RZG2L_SINGLE_PIN_PACK(p, b, f) (RZG2L_SINGLE_PIN | \
((p) << 24) | ((b) << 20) | (f))
-#define RZG2L_SINGLE_PIN_GET_PORT_OFFSET(x) (((x) & GENMASK(30, 24)) >> 24)
#define RZG2L_SINGLE_PIN_GET_BIT(x) (((x) & GENMASK(22, 20)) >> 20)
-#define RZG2L_SINGLE_PIN_GET_CFGS(x) ((x) & GENMASK(19, 0))
-
-#define P(n) (0x0000 + 0x10 + (n))
-#define PM(n) (0x0100 + 0x20 + (n) * 2)
-#define PMC(n) (0x0200 + 0x10 + (n))
-#define PFC(n) (0x0400 + 0x40 + (n) * 4)
-#define PIN(n) (0x0800 + 0x10 + (n))
-#define IOLH(n) (0x1000 + (n) * 8)
-#define IEN(n) (0x1800 + (n) * 8)
-#define ISEL(n) (0x2c80 + (n) * 8)
+
+#define RZG2L_PIN_CFG_TO_CAPS(cfg) ((cfg) & GENMASK(19, 0))
+#define RZG2L_PIN_CFG_TO_PORT_OFFSET(cfg) ((cfg) & RZG2L_SINGLE_PIN ? \
+ (((cfg) & GENMASK(30, 24)) >> 24) : \
+ (((cfg) & GENMASK(26, 20)) >> 20))
+
+#define P(off) (0x0000 + (off))
+#define PM(off) (0x0100 + (off) * 2)
+#define PMC(off) (0x0200 + (off))
+#define PFC(off) (0x0400 + (off) * 4)
+#define PIN(off) (0x0800 + (off))
+#define IOLH(off) (0x1000 + (off) * 8)
+#define IEN(off) (0x1800 + (off) * 8)
+#define ISEL(off) (0x2C00 + (off) * 8)
#define PWPR (0x3014)
#define SD_CH(n) (0x3000 + (n) * 4)
#define QSPI (0x3008)
@@ -117,7 +118,6 @@
#define PM_OUTPUT 0x2

#define RZG2L_PIN_ID_TO_PORT(id) ((id) / RZG2L_PINS_PER_PORT)
-#define RZG2L_PIN_ID_TO_PORT_OFFSET(id) (RZG2L_PIN_ID_TO_PORT(id) + 0x10)
#define RZG2L_PIN_ID_TO_PIN(id) ((id) % RZG2L_PINS_PER_PORT)

#define RZG2L_TINT_MAX_INTERRUPT 32
@@ -161,7 +161,7 @@ static const unsigned int iolh_groupa_mA[] = { 2, 4, 8, 12 };
static const unsigned int iolh_groupb_oi[] = { 100, 66, 50, 33 };

static void rzg2l_pinctrl_set_pfc_mode(struct rzg2l_pinctrl *pctrl,
- u8 port, u8 pin, u8 func)
+ u8 pin, u8 off, u8 func)
{
unsigned long flags;
u32 reg;
@@ -169,30 +169,30 @@ static void rzg2l_pinctrl_set_pfc_mode(struct rzg2l_pinctrl *pctrl,
spin_lock_irqsave(&pctrl->lock, flags);

/* Set pin to 'Non-use (Hi-Z input protection)' */
- reg = readw(pctrl->base + PM(port));
+ reg = readw(pctrl->base + PM(off));
reg &= ~(PM_MASK << (pin * 2));
- writew(reg, pctrl->base + PM(port));
+ writew(reg, pctrl->base + PM(off));

/* Temporarily switch to GPIO mode with PMC register */
- reg = readb(pctrl->base + PMC(port));
- writeb(reg & ~BIT(pin), pctrl->base + PMC(port));
+ reg = readb(pctrl->base + PMC(off));
+ writeb(reg & ~BIT(pin), pctrl->base + PMC(off));

/* Set the PWPR register to allow PFC register to write */
writel(0x0, pctrl->base + PWPR); /* B0WI=0, PFCWE=0 */
writel(PWPR_PFCWE, pctrl->base + PWPR); /* B0WI=0, PFCWE=1 */

/* Select Pin function mode with PFC register */
- reg = readl(pctrl->base + PFC(port));
+ reg = readl(pctrl->base + PFC(off));
reg &= ~(PFC_MASK << (pin * 4));
- writel(reg | (func << (pin * 4)), pctrl->base + PFC(port));
+ writel(reg | (func << (pin * 4)), pctrl->base + PFC(off));

/* Set the PWPR register to be write-protected */
writel(0x0, pctrl->base + PWPR); /* B0WI=0, PFCWE=0 */
writel(PWPR_B0WI, pctrl->base + PWPR); /* B0WI=1, PFCWE=0 */

/* Switch to Peripheral pin function with PMC register */
- reg = readb(pctrl->base + PMC(port));
- writeb(reg | BIT(pin), pctrl->base + PMC(port));
+ reg = readb(pctrl->base + PMC(off));
+ writeb(reg | BIT(pin), pctrl->base + PMC(off));

spin_unlock_irqrestore(&pctrl->lock, flags);
};
@@ -202,9 +202,11 @@ static int rzg2l_pinctrl_set_mux(struct pinctrl_dev *pctldev,
unsigned int group_selector)
{
struct rzg2l_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
+ const struct pinctrl_pin_desc *pin_desc;
+ unsigned int *psel_val, *pin_data;
struct function_desc *func;
- unsigned int i, *psel_val;
struct group_desc *group;
+ u32 pin, off;
int *pins;

func = pinmux_generic_get_function(pctldev, func_selector);
@@ -217,12 +219,17 @@ static int rzg2l_pinctrl_set_mux(struct pinctrl_dev *pctldev,
psel_val = func->data;
pins = group->pins;

- for (i = 0; i < group->num_pins; i++) {
- dev_dbg(pctrl->dev, "port:%u pin: %u PSEL:%u\n",
- RZG2L_PIN_ID_TO_PORT(pins[i]), RZG2L_PIN_ID_TO_PIN(pins[i]),
- psel_val[i]);
- rzg2l_pinctrl_set_pfc_mode(pctrl, RZG2L_PIN_ID_TO_PORT(pins[i]),
- RZG2L_PIN_ID_TO_PIN(pins[i]), psel_val[i]);
+ for (unsigned int i = 0; i < group->num_pins; i++) {
+ pin_desc = &pctrl->desc.pins[pins[i]];
+ pin_data = pin_desc->drv_data;
+
+ pin = RZG2L_PIN_ID_TO_PIN(pins[i]);
+ off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
+
+ dev_dbg(pctrl->dev, "port:%u pin: %u off:%x PSEL:%u\n",
+ RZG2L_PIN_ID_TO_PORT(pins[i]), pin, off, psel_val[i]);
+
+ rzg2l_pinctrl_set_pfc_mode(pctrl, pin, off, psel_val[i]);
}

return 0;
@@ -468,14 +475,14 @@ static int rzg2l_validate_gpio_pin(struct rzg2l_pinctrl *pctrl,
u32 cfg, u32 port, u8 bit)
{
u8 pincount = RZG2L_GPIO_PORT_GET_PINCNT(cfg);
- u32 port_index = RZG2L_GPIO_PORT_GET_INDEX(cfg);
+ u32 off = RZG2L_PIN_CFG_TO_PORT_OFFSET(cfg);
u32 data;

if (bit >= pincount || port >= pctrl->data->n_port_pins)
return -EINVAL;

data = pctrl->data->port_pin_configs[port];
- if (port_index != RZG2L_GPIO_PORT_GET_INDEX(data))
+ if (off != RZG2L_PIN_CFG_TO_PORT_OFFSET(data))
return -EINVAL;

return 0;
@@ -525,20 +532,17 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
unsigned int arg = 0;
unsigned long flags;
void __iomem *addr;
- u32 port_offset;
- u32 cfg = 0;
- u8 bit = 0;
+ u32 off, cfg;
+ u8 bit;

if (!pin_data)
return -EINVAL;

+ off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
+ cfg = RZG2L_PIN_CFG_TO_CAPS(*pin_data);
if (*pin_data & RZG2L_SINGLE_PIN) {
- port_offset = RZG2L_SINGLE_PIN_GET_PORT_OFFSET(*pin_data);
- cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
} else {
- cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
- port_offset = RZG2L_PIN_ID_TO_PORT_OFFSET(_pin);
bit = RZG2L_PIN_ID_TO_PIN(_pin);

if (rzg2l_validate_gpio_pin(pctrl, *pin_data, RZG2L_PIN_ID_TO_PORT(_pin), bit))
@@ -549,7 +553,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
case PIN_CONFIG_INPUT_ENABLE:
if (!(cfg & PIN_CFG_IEN))
return -EINVAL;
- arg = rzg2l_read_pin_config(pctrl, IEN(port_offset), bit, IEN_MASK);
+ arg = rzg2l_read_pin_config(pctrl, IEN(off), bit, IEN_MASK);
if (!arg)
return -EINVAL;
break;
@@ -579,7 +583,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
if (!(cfg & PIN_CFG_IOLH_A))
return -EINVAL;

- index = rzg2l_read_pin_config(pctrl, IOLH(port_offset), bit, IOLH_MASK);
+ index = rzg2l_read_pin_config(pctrl, IOLH(off), bit, IOLH_MASK);
arg = iolh_groupa_mA[index];
break;
}
@@ -590,7 +594,7 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
if (!(cfg & PIN_CFG_IOLH_B))
return -EINVAL;

- index = rzg2l_read_pin_config(pctrl, IOLH(port_offset), bit, IOLH_MASK);
+ index = rzg2l_read_pin_config(pctrl, IOLH(off), bit, IOLH_MASK);
arg = iolh_groupb_oi[index];
break;
}
@@ -615,21 +619,18 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
enum pin_config_param param;
unsigned long flags;
void __iomem *addr;
- u32 port_offset;
unsigned int i;
- u32 cfg = 0;
- u8 bit = 0;
+ u32 cfg, off;
+ u8 bit;

if (!pin_data)
return -EINVAL;

+ off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
+ cfg = RZG2L_PIN_CFG_TO_CAPS(*pin_data);
if (*pin_data & RZG2L_SINGLE_PIN) {
- port_offset = RZG2L_SINGLE_PIN_GET_PORT_OFFSET(*pin_data);
- cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
} else {
- cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
- port_offset = RZG2L_PIN_ID_TO_PORT_OFFSET(_pin);
bit = RZG2L_PIN_ID_TO_PIN(_pin);

if (rzg2l_validate_gpio_pin(pctrl, *pin_data, RZG2L_PIN_ID_TO_PORT(_pin), bit))
@@ -646,7 +647,7 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
if (!(cfg & PIN_CFG_IEN))
return -EINVAL;

- rzg2l_rmw_pin_config(pctrl, IEN(port_offset), bit, IEN_MASK, !!arg);
+ rzg2l_rmw_pin_config(pctrl, IEN(off), bit, IEN_MASK, !!arg);
break;
}

@@ -687,7 +688,7 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
if (index >= ARRAY_SIZE(iolh_groupa_mA))
return -EINVAL;

- rzg2l_rmw_pin_config(pctrl, IOLH(port_offset), bit, IOLH_MASK, index);
+ rzg2l_rmw_pin_config(pctrl, IOLH(off), bit, IOLH_MASK, index);
break;
}

@@ -705,7 +706,7 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
if (index >= ARRAY_SIZE(iolh_groupb_oi))
return -EINVAL;

- rzg2l_rmw_pin_config(pctrl, IOLH(port_offset), bit, IOLH_MASK, index);
+ rzg2l_rmw_pin_config(pctrl, IOLH(off), bit, IOLH_MASK, index);
break;
}

@@ -795,7 +796,9 @@ static const struct pinconf_ops rzg2l_pinctrl_confops = {
static int rzg2l_gpio_request(struct gpio_chip *chip, unsigned int offset)
{
struct rzg2l_pinctrl *pctrl = gpiochip_get_data(chip);
- u32 port = RZG2L_PIN_ID_TO_PORT(offset);
+ const struct pinctrl_pin_desc *pin_desc = &pctrl->desc.pins[offset];
+ unsigned int *pin_data = pin_desc->drv_data;
+ u32 off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
u8 bit = RZG2L_PIN_ID_TO_PIN(offset);
unsigned long flags;
u8 reg8;
@@ -808,28 +811,32 @@ static int rzg2l_gpio_request(struct gpio_chip *chip, unsigned int offset)
spin_lock_irqsave(&pctrl->lock, flags);

/* Select GPIO mode in PMC Register */
- reg8 = readb(pctrl->base + PMC(port));
+ reg8 = readb(pctrl->base + PMC(off));
reg8 &= ~BIT(bit);
- writeb(reg8, pctrl->base + PMC(port));
+ writeb(reg8, pctrl->base + PMC(off));

spin_unlock_irqrestore(&pctrl->lock, flags);

return 0;
}

-static void rzg2l_gpio_set_direction(struct rzg2l_pinctrl *pctrl, u32 port,
- u8 bit, bool output)
+static void rzg2l_gpio_set_direction(struct rzg2l_pinctrl *pctrl, u32 offset,
+ bool output)
{
+ const struct pinctrl_pin_desc *pin_desc = &pctrl->desc.pins[offset];
+ unsigned int *pin_data = pin_desc->drv_data;
+ u32 off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
+ u8 bit = RZG2L_PIN_ID_TO_PIN(offset);
unsigned long flags;
u16 reg16;

spin_lock_irqsave(&pctrl->lock, flags);

- reg16 = readw(pctrl->base + PM(port));
+ reg16 = readw(pctrl->base + PM(off));
reg16 &= ~(PM_MASK << (bit * 2));

reg16 |= (output ? PM_OUTPUT : PM_INPUT) << (bit * 2);
- writew(reg16, pctrl->base + PM(port));
+ writew(reg16, pctrl->base + PM(off));

spin_unlock_irqrestore(&pctrl->lock, flags);
}
@@ -837,13 +844,15 @@ static void rzg2l_gpio_set_direction(struct rzg2l_pinctrl *pctrl, u32 port,
static int rzg2l_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
{
struct rzg2l_pinctrl *pctrl = gpiochip_get_data(chip);
- u32 port = RZG2L_PIN_ID_TO_PORT(offset);
+ const struct pinctrl_pin_desc *pin_desc = &pctrl->desc.pins[offset];
+ unsigned int *pin_data = pin_desc->drv_data;
+ u32 off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
u8 bit = RZG2L_PIN_ID_TO_PIN(offset);

- if (!(readb(pctrl->base + PMC(port)) & BIT(bit))) {
+ if (!(readb(pctrl->base + PMC(off)) & BIT(bit))) {
u16 reg16;

- reg16 = readw(pctrl->base + PM(port));
+ reg16 = readw(pctrl->base + PM(off));
reg16 = (reg16 >> (bit * 2)) & PM_MASK;
if (reg16 == PM_OUTPUT)
return GPIO_LINE_DIRECTION_OUT;
@@ -856,10 +865,8 @@ static int rzg2l_gpio_direction_input(struct gpio_chip *chip,
unsigned int offset)
{
struct rzg2l_pinctrl *pctrl = gpiochip_get_data(chip);
- u32 port = RZG2L_PIN_ID_TO_PORT(offset);
- u8 bit = RZG2L_PIN_ID_TO_PIN(offset);

- rzg2l_gpio_set_direction(pctrl, port, bit, false);
+ rzg2l_gpio_set_direction(pctrl, offset, false);

return 0;
}
@@ -868,19 +875,21 @@ static void rzg2l_gpio_set(struct gpio_chip *chip, unsigned int offset,
int value)
{
struct rzg2l_pinctrl *pctrl = gpiochip_get_data(chip);
- u32 port = RZG2L_PIN_ID_TO_PORT(offset);
+ const struct pinctrl_pin_desc *pin_desc = &pctrl->desc.pins[offset];
+ unsigned int *pin_data = pin_desc->drv_data;
+ u32 off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
u8 bit = RZG2L_PIN_ID_TO_PIN(offset);
unsigned long flags;
u8 reg8;

spin_lock_irqsave(&pctrl->lock, flags);

- reg8 = readb(pctrl->base + P(port));
+ reg8 = readb(pctrl->base + P(off));

if (value)
- writeb(reg8 | BIT(bit), pctrl->base + P(port));
+ writeb(reg8 | BIT(bit), pctrl->base + P(off));
else
- writeb(reg8 & ~BIT(bit), pctrl->base + P(port));
+ writeb(reg8 & ~BIT(bit), pctrl->base + P(off));

spin_unlock_irqrestore(&pctrl->lock, flags);
}
@@ -889,11 +898,9 @@ static int rzg2l_gpio_direction_output(struct gpio_chip *chip,
unsigned int offset, int value)
{
struct rzg2l_pinctrl *pctrl = gpiochip_get_data(chip);
- u32 port = RZG2L_PIN_ID_TO_PORT(offset);
- u8 bit = RZG2L_PIN_ID_TO_PIN(offset);

rzg2l_gpio_set(chip, offset, value);
- rzg2l_gpio_set_direction(pctrl, port, bit, true);
+ rzg2l_gpio_set_direction(pctrl, offset, true);

return 0;
}
@@ -901,17 +908,19 @@ static int rzg2l_gpio_direction_output(struct gpio_chip *chip,
static int rzg2l_gpio_get(struct gpio_chip *chip, unsigned int offset)
{
struct rzg2l_pinctrl *pctrl = gpiochip_get_data(chip);
- u32 port = RZG2L_PIN_ID_TO_PORT(offset);
+ const struct pinctrl_pin_desc *pin_desc = &pctrl->desc.pins[offset];
+ unsigned int *pin_data = pin_desc->drv_data;
+ u32 off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
u8 bit = RZG2L_PIN_ID_TO_PIN(offset);
u16 reg16;

- reg16 = readw(pctrl->base + PM(port));
+ reg16 = readw(pctrl->base + PM(off));
reg16 = (reg16 >> (bit * 2)) & PM_MASK;

if (reg16 == PM_INPUT)
- return !!(readb(pctrl->base + PIN(port)) & BIT(bit));
+ return !!(readb(pctrl->base + PIN(off)) & BIT(bit));
else if (reg16 == PM_OUTPUT)
- return !!(readb(pctrl->base + P(port)) & BIT(bit));
+ return !!(readb(pctrl->base + P(off)) & BIT(bit));
else
return -EINVAL;
}
@@ -1170,17 +1179,16 @@ static void rzg2l_gpio_irq_disable(struct irq_data *d)
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct rzg2l_pinctrl *pctrl = container_of(gc, struct rzg2l_pinctrl, gpio_chip);
unsigned int hwirq = irqd_to_hwirq(d);
+ const struct pinctrl_pin_desc *pin_desc = &pctrl->desc.pins[hwirq];
+ unsigned int *pin_data = pin_desc->drv_data;
+ u32 off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
+ u8 bit = RZG2L_PIN_ID_TO_PIN(hwirq);
unsigned long flags;
void __iomem *addr;
- u32 port;
- u8 bit;

irq_chip_disable_parent(d);

- port = RZG2L_PIN_ID_TO_PORT(hwirq);
- bit = RZG2L_PIN_ID_TO_PIN(hwirq);
-
- addr = pctrl->base + ISEL(port);
+ addr = pctrl->base + ISEL(off);
if (bit >= 4) {
bit -= 4;
addr += 4;
@@ -1198,17 +1206,16 @@ static void rzg2l_gpio_irq_enable(struct irq_data *d)
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct rzg2l_pinctrl *pctrl = container_of(gc, struct rzg2l_pinctrl, gpio_chip);
unsigned int hwirq = irqd_to_hwirq(d);
+ const struct pinctrl_pin_desc *pin_desc = &pctrl->desc.pins[hwirq];
+ unsigned int *pin_data = pin_desc->drv_data;
+ u32 off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);
+ u8 bit = RZG2L_PIN_ID_TO_PIN(hwirq);
unsigned long flags;
void __iomem *addr;
- u32 port;
- u8 bit;

gpiochip_enable_irq(gc, hwirq);

- port = RZG2L_PIN_ID_TO_PORT(hwirq);
- bit = RZG2L_PIN_ID_TO_PIN(hwirq);
-
- addr = pctrl->base + ISEL(port);
+ addr = pctrl->base + ISEL(off);
if (bit >= 4) {
bit -= 4;
addr += 4;
--
2.39.2


2023-10-04 12:53:16

by Geert Uytterhoeven

[permalink] [raw]
Subject: Re: [PATCH v2 14/28] pinctrl: renesas: rzg2l: index all registers based on port offset

Hi Claudiu,

On Fri, Sep 29, 2023 at 7:39 AM Claudiu <[email protected]> wrote:
> From: Claudiu Beznea <[email protected]>
>
> To get address that needs to be read/write for specific port
> functionalities the P(), PM(), PMC(), PFC(), PIN(), IOLH() IEN(), ISEL()
> macros are used. Some of these macros received as argument the hardware
> port identifier, some hardware port offset address (e.g. ISEL() received
> port identifier, IOLH() received port offset address). This makes hard to
> extend the current driver for SoCs were port identifiers are not continuous
> in memory map of pin controller. This is the case for RZ/G3S pin controller
> were ports are mapped as follows:
>
> port offset port identifier
> ----------- ---------------
> 0x20 P0
> 0x21 P5
> 0x22 P6
> 0x23 P11
> 0x24 P12
> 0x25 P13
> 0x26 P14
> 0x27 P15
> 0x28 P16
> 0x29 P17
> 0x2a P18
> 0x30 P1
> 0x31 P2
> 0x32 P3
> 0x33 P4
> 0x34 P7
> 0x35 P8
> 0x36 P8
> 0x37 P10
>
> To make this achievable change all the above macros used to get the address
> of a port register for specific port functionality based on port hardware
> address. Shortly, all the above macros will get as argument the port
> offset address listed in the above table.
>
> With this RZG2L_SINGLE_PIN_GET_PORT_OFFSET(), RZG2L_PIN_ID_TO_PORT_OFFSET()
> and RZG2L_GPIO_PORT_GET_INDEX() were replaced by
> RZG2L_PIN_CFG_TO_PORT_OFFSET(), RZG2L_SINGLE_PIN_GET_CFGS() and
> RZG2L_GPIO_PORT_GET_CFGS() were replaced by RZG2L_PIN_CFG_TO_CAPS().
>
> Also rzg2l_pinctrl_set_pfc_mode() don't need port argument anymore.
> Also rzg2l_gpio_direction_input() and rzg2l_gpio_direction_output() don't
> need to translate port and bit locally as this can be done by
> rzg2l_gpio_set_direction().
>
> To use the same naming for port, bit/pin and register offset the
> port_offset variable names in different places was replaced by variable
> named off and there is no need to initialize anymore cfg and bit in
> different code places.
>
> Signed-off-by: Claudiu Beznea <[email protected]>
> Reviewed-by: Geert Uytterhoeven <[email protected]>
> Reviewed-by: Lad Prabhakar <[email protected]>
> Tested-by: Lad Prabhakar <[email protected]>
> ---
>
> Changes in v2:
> - mentioned in commit description about the replacement of
> RZG2L_GPIO_PORT_GET_INDEX() with RZG2L_PIN_CFG_TO_PORT_OFFSET()
> - moved variable declaration inside for()
> - got rid of local variable and used directly RZG2L_PIN_ID_TO_PORT() in
> debug message from rzg2l_pinctrl_set_mux() function
> - collected tags

Thanks for the update! Sill queue in renesas-pinctrl-for-v6.7.

> --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> @@ -202,9 +202,11 @@ static int rzg2l_pinctrl_set_mux(struct pinctrl_dev *pctldev,
> unsigned int group_selector)
> {
> struct rzg2l_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> + const struct pinctrl_pin_desc *pin_desc;
> + unsigned int *psel_val, *pin_data;
> struct function_desc *func;
> - unsigned int i, *psel_val;
> struct group_desc *group;
> + u32 pin, off;
> int *pins;
>
> func = pinmux_generic_get_function(pctldev, func_selector);
> @@ -217,12 +219,17 @@ static int rzg2l_pinctrl_set_mux(struct pinctrl_dev *pctldev,
> psel_val = func->data;
> pins = group->pins;
>
> - for (i = 0; i < group->num_pins; i++) {
> - dev_dbg(pctrl->dev, "port:%u pin: %u PSEL:%u\n",
> - RZG2L_PIN_ID_TO_PORT(pins[i]), RZG2L_PIN_ID_TO_PIN(pins[i]),
> - psel_val[i]);
> - rzg2l_pinctrl_set_pfc_mode(pctrl, RZG2L_PIN_ID_TO_PORT(pins[i]),
> - RZG2L_PIN_ID_TO_PIN(pins[i]), psel_val[i]);
> + for (unsigned int i = 0; i < group->num_pins; i++) {
> + pin_desc = &pctrl->desc.pins[pins[i]];
> + pin_data = pin_desc->drv_data;
> +
> + pin = RZG2L_PIN_ID_TO_PIN(pins[i]);
> + off = RZG2L_PIN_CFG_TO_PORT_OFFSET(*pin_data);

In my comments on v1, I actually meant to combine these assignments
to variables with the variable declarations. I will handle that while applying.

> +
> + dev_dbg(pctrl->dev, "port:%u pin: %u off:%x PSEL:%u\n",
> + RZG2L_PIN_ID_TO_PORT(pins[i]), pin, off, psel_val[i]);
> +
> + rzg2l_pinctrl_set_pfc_mode(pctrl, pin, off, psel_val[i]);
> }
>
> return 0;

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds