Hi,
This adds adds support for the UNI-T UTi260B thermal camera, which is based
on i.MX6ULL. Patches 1-14 clean up all warnings reported by CHECK_DTBS for
i.MX6ULL (i.e. for an empty board). They are not specific to the UTi260B and
in fact that machine has most of the IP handled by these patches marked as
disabled. Then patches 15+16 introduce the vendor and board compatible DT
bindings. Finally the last patches adds support for the thermal camera itself.
The DT is based on reverse engineered information. More information about
the device can be found in this presentation from Embedded Recipes 2023:
* https://embedded-recipes.org/2023/wp-content/uploads/2023/10/Running-FOSS-on-a-Thermal-Camera-Sebastian-Reichel-compressed.pdf
* https://www.youtube.com/watch?v=uvObsCG-Cqo
I also prepared a branch with these patches (and a minimal kernel config)
and published it here:
https://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-misc.git/log/?h=uti260b-v2
Changes since PATCHv1:
* https://lore.kernel.org/all/[email protected]/
- uni-t,imx6ull-uti260b -> uni-t,uti260b
- add Acked-by for uni-t vendor prefix
- add Acked-by for HDMI audio index fix
- add Acked-by for LCDIF power-domain requirement drop
- anatop DT binding: Fixed indentation in example
- anatop DT binding: Described IRQs
- touchscreen DT binding: change tsc@ to touchscreen@ in example
- touchscreen DT binding: change xnur-gpio to xnur-gpios
- weim DT binding: drop acme,whatever example
- weim DT binding: use flash@ instead of nor@
- weim DT binding: update weim.txt reference in arcx,anybus-controller.txt
- weim DT binding: switch to memory-controller binding
- fsl,imx-asrc DT binding: fix ASoC patch subject prefix
- fsl,imx-asrc DT binding: add constraints
- add new patch fixing xnur-gpio(s) in all i.MX6UL board DT files
- add new patch fixing touchscreen nodename in i.MX6UL SoC DT file
- add new patch fixing weim nodename in all i.MX SoC DT files
- device DTS: use color/functions for the led
- device DTS: increase SPI speed
- device DTS: add comment for SD / eMMC node
Unadressed feedback from PATCHv1:
- anatop phandle vs parent: technically it makes sense to just use the
parent, but this driver is only used by i.MX6. The current code makes
use of the phandle, so we cannot drop it because of backwards
compatibility. So I don't see a point in deprecating this property.
- touchscreen binding: I kept measure-delay-time and pre-charge-time
values in hex, since that is being used everywhere and the unit
is unknown. The values are directly written into HW registers and
the i.MX6UL TRM does not provide any hints about the unit. I do not
have an i.MX6UL device with a touchsreen, so I cannot test either.
- regulator name in DT: I did not rename the regulators to just
"regulator", since the nodename must be unique.
Greetings,
-- Sebastian
Sebastian Reichel (17):
dt-bindings: pinctrl: fsl,imx6ul-pinctrl: convert to YAML
dt-bindings: bus: imx-weim: convert to YAML
ASoC: dt-bindings: fsl,imx-asrc: convert to YAML
dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML
dt-bindings: soc: imx: fsl,imx-anatop: add binding
dt-bindings: soc: imx: fsl,imx-iomuxc-gpr: add imx6
dt-bindings: lcdif: Do not require power-domains for i.MX6ULL
dt-bindings: fsl-imx-sdma: fix HDMI audio index
ARM: dts: imx6ull: fix pinctrl node name
ARM: dts: imx6ul: Remove fsl,anatop from usbotg1
ARM: dts: imx6ul: add missing #thermal-sensor-cells
ARM: dts: nxp: imx6ul: xnur-gpio -> xnur-gpios
ARM: dts: nxp: imx6ul: fix touchscreen node name
ARM: dts: nxp: imx: fix weim node name
dt-bindings: vendor-prefixes: add UNI-T
dt-bindings: arm: add UNI-T UTi260b
ARM: dts: imx6ull-uti260b: Add board
.../devicetree/bindings/arm/fsl.yaml | 1 +
.../devicetree/bindings/bus/imx-weim.txt | 117 ----
.../bindings/display/fsl,lcdif.yaml | 8 +-
.../devicetree/bindings/dma/fsl,imx-sdma.yaml | 3 +-
.../input/touchscreen/fsl,imx6ul-tsc.yaml | 97 +++
.../bindings/input/touchscreen/imx6ul_tsc.txt | 38 --
.../fsl/fsl,imx-weim-peripherals.yaml | 36 ++
.../memory-controllers/fsl/fsl,imx-weim.yaml | 201 ++++++
.../mc-peripheral-props.yaml | 1 +
.../bindings/pinctrl/fsl,imx6ul-pinctrl.txt | 37 --
.../bindings/pinctrl/fsl,imx6ul-pinctrl.yaml | 116 ++++
.../bindings/soc/imx/fsl,imx-anatop.yaml | 128 ++++
.../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml | 18 +-
.../devicetree/bindings/sound/fsl,asrc.txt | 80 ---
.../bindings/sound/fsl,imx-asrc.yaml | 162 +++++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
arch/arm/boot/dts/nxp/imx/imx1.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx27.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx31.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx35.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx51.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6sl.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6sx.dtsi | 2 +-
.../boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts | 2 +-
.../nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 6 +-
.../boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts | 572 ++++++++++++++++++
arch/arm/boot/dts/nxp/imx/imx6ull.dtsi | 2 +-
.../fieldbus/arcx,anybus-controller.txt | 2 +-
33 files changed, 1360 insertions(+), 292 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
delete mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/soc/imx/fsl,imx-anatop.yaml
delete mode 100644 Documentation/devicetree/bindings/sound/fsl,asrc.txt
create mode 100644 Documentation/devicetree/bindings/sound/fsl,imx-asrc.yaml
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
--
2.43.0
Convert the i.MX Wireless External Interface Module binding to YAML.
Signed-off-by: Sebastian Reichel <[email protected]>
---
.../devicetree/bindings/bus/imx-weim.txt | 117 ----------
.../fsl/fsl,imx-weim-peripherals.yaml | 36 ++++
.../memory-controllers/fsl/fsl,imx-weim.yaml | 201 ++++++++++++++++++
.../mc-peripheral-props.yaml | 1 +
.../fieldbus/arcx,anybus-controller.txt | 2 +-
5 files changed, 239 insertions(+), 118 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt
deleted file mode 100644
index e7f502070d77..000000000000
--- a/Documentation/devicetree/bindings/bus/imx-weim.txt
+++ /dev/null
@@ -1,117 +0,0 @@
-Device tree bindings for i.MX Wireless External Interface Module (WEIM)
-
-The term "wireless" does not imply that the WEIM is literally an interface
-without wires. It simply means that this module was originally designed for
-wireless and mobile applications that use low-power technology.
-
-The actual devices are instantiated from the child nodes of a WEIM node.
-
-Required properties:
-
- - compatible: Should contain one of the following:
- "fsl,imx1-weim"
- "fsl,imx27-weim"
- "fsl,imx51-weim"
- "fsl,imx50-weim"
- "fsl,imx6q-weim"
- - reg: A resource specifier for the register space
- (see the example below)
- - clocks: the clock, see the example below.
- - #address-cells: Must be set to 2 to allow memory address translation
- - #size-cells: Must be set to 1 to allow CS address passing
- - ranges: Must be set up to reflect the memory layout with four
- integer values for each chip-select line in use:
-
- <cs-number> 0 <physical address of mapping> <size>
-
-Optional properties:
-
- - fsl,weim-cs-gpr: For "fsl,imx50-weim" and "fsl,imx6q-weim" type of
- devices, it should be the phandle to the system General
- Purpose Register controller that contains WEIM CS GPR
- register, e.g. IOMUXC_GPR1 on i.MX6Q. IOMUXC_GPR1[11:0]
- should be set up as one of the following 4 possible
- values depending on the CS space configuration.
-
- IOMUXC_GPR1[11:0] CS0 CS1 CS2 CS3
- ---------------------------------------------
- 05 128M 0M 0M 0M
- 033 64M 64M 0M 0M
- 0113 64M 32M 32M 0M
- 01111 32M 32M 32M 32M
-
- In case that the property is absent, the reset value or
- what bootloader sets up in IOMUXC_GPR1[11:0] will be
- used.
-
- - fsl,burst-clk-enable For "fsl,imx50-weim" and "fsl,imx6q-weim" type of
- devices, the presence of this property indicates that
- the weim bus should operate in Burst Clock Mode.
-
- - fsl,continuous-burst-clk Make Burst Clock to output continuous clock.
- Without this option Burst Clock will output clock
- only when necessary. This takes effect only if
- "fsl,burst-clk-enable" is set.
-
-Timing property for child nodes. It is mandatory, not optional.
-
- - fsl,weim-cs-timing: The timing array, contains timing values for the
- child node. We get the CS indexes from the address
- ranges in the child node's "reg" property.
- The number of registers depends on the selected chip:
- For i.MX1, i.MX21 ("fsl,imx1-weim") there are two
- registers: CSxU, CSxL.
- For i.MX25, i.MX27, i.MX31 and i.MX35 ("fsl,imx27-weim")
- there are three registers: CSCRxU, CSCRxL, CSCRxA.
- For i.MX50, i.MX53 ("fsl,imx50-weim"),
- i.MX51 ("fsl,imx51-weim") and i.MX6Q ("fsl,imx6q-weim")
- there are six registers: CSxGCR1, CSxGCR2, CSxRCR1,
- CSxRCR2, CSxWCR1, CSxWCR2.
-
-Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
-
- weim: weim@21b8000 {
- compatible = "fsl,imx6q-weim";
- reg = <0x021b8000 0x4000>;
- clocks = <&clks 196>;
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0x08000000 0x08000000>;
- fsl,weim-cs-gpr = <&gpr>;
-
- nor@0,0 {
- compatible = "cfi-flash";
- reg = <0 0 0x02000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- bank-width = <2>;
- fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
- 0x0000c000 0x1404a38e 0x00000000>;
- };
- };
-
-Example for an imx6q-based board, a multi-chipselect device connected to WEIM:
-
-In this case, both chip select 0 and 1 will be configured with the same timing
-array values.
-
- weim: weim@21b8000 {
- compatible = "fsl,imx6q-weim";
- reg = <0x021b8000 0x4000>;
- clocks = <&clks 196>;
- #address-cells = <2>;
- #size-cells = <1>;
- ranges = <0 0 0x08000000 0x02000000
- 1 0 0x0a000000 0x02000000
- 2 0 0x0c000000 0x02000000
- 3 0 0x0e000000 0x02000000>;
- fsl,weim-cs-gpr = <&gpr>;
-
- acme@0 {
- compatible = "acme,whatever";
- reg = <0 0 0x100>, <0 0x400000 0x800>,
- <1 0x400000 0x800>;
- fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100
- 0x00000000 0xa0000240 0x00000000>;
- };
- };
diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
new file mode 100644
index 000000000000..86d7e5011107
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: i.MX WEIM Bus Peripheral Nodes
+
+maintainers:
+ - Shawn Guo <[email protected]>
+ - Sascha Hauer <[email protected]>
+
+description:
+ This binding is meant for the child nodes of the WEIM node. The node
+ represents any device connected to the WEIM bus. It may be a Flash chip,
+ RAM chip or Ethernet controller, etc. These properties are meant for
+ configuring the WEIM settings/timings and will accompany the bindings
+ supported by the respective device.
+
+properties:
+ reg: true
+
+ fsl,weim-cs-timing:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description:
+ Timing values for the child node.
+ minItems: 2
+ maxItems: 6
+
+required:
+ - compatible
+ - reg
+ - fsl,weim-cs-timing
+
+# the WEIM child will have its own native properties
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
new file mode 100644
index 000000000000..a2c96da683bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
@@ -0,0 +1,201 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,imx-weim.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: i.MX Wireless External Interface Module (WEIM)
+
+maintainers:
+ - Shawn Guo <[email protected]>
+ - Sascha Hauer <[email protected]>
+
+description:
+ The term "wireless" does not imply that the WEIM is literally an interface
+ without wires. It simply means that this module was originally designed for
+ wireless and mobile applications that use low-power technology. The actual
+ devices are instantiated from the child nodes of a WEIM node.
+
+properties:
+ $nodename:
+ pattern: "^memory-controller@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - enum:
+ - fsl,imx1-weim
+ - fsl,imx27-weim
+ - fsl,imx50-weim
+ - fsl,imx51-weim
+ - fsl,imx6q-weim
+ - items:
+ - enum:
+ - fsl,imx31-weim
+ - fsl,imx35-weim
+ - const: fsl,imx27-weim
+ - items:
+ - enum:
+ - fsl,imx6sx-weim
+ - fsl,imx6ul-weim
+ - const: fsl,imx6q-weim
+
+ '#address-cells':
+ const: 2
+
+ '#size-cells':
+ const: 1
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ ranges: true
+
+ fsl,weim-cs-gpr:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: |
+ Phandle to the system General Purpose Register controller that contains
+ WEIM CS GPR register, e.g. IOMUXC_GPR1 on i.MX6Q. IOMUXC_GPR1[11:0]
+ should be set up as one of the following 4 possible values depending on
+ the CS space configuration.
+
+ IOMUXC_GPR1[11:0] CS0 CS1 CS2 CS3
+ ---------------------------------------------
+ 05 128M 0M 0M 0M
+ 033 64M 64M 0M 0M
+ 0113 64M 32M 32M 0M
+ 01111 32M 32M 32M 32M
+
+ In case that the property is absent, the reset value or what bootloader
+ sets up in IOMUXC_GPR1[11:0] will be used.
+
+ fsl,burst-clk-enable:
+ type: boolean
+ description:
+ The presence of this property indicates that the weim bus should operate
+ in Burst Clock Mode.
+
+ fsl,continuous-burst-clk:
+ type: boolean
+ description:
+ Make Burst Clock to output continuous clock. Without this option Burst
+ Clock will output clock only when necessary.
+
+patternProperties:
+ "^.*@[0-7],[0-9a-f]+$":
+ type: object
+ description: Devices attached to chip selects are represented as subnodes.
+ $ref: fsl,imx-weim-peripherals.yaml
+ additionalProperties: true
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - '#address-cells'
+ - '#size-cells'
+ - ranges
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ not:
+ contains:
+ enum:
+ - fsl,imx50-weim
+ - fsl,imx6q-weim
+ then:
+ properties:
+ fsl,weim-cs-gpr: false
+ fsl,burst-clk-enable: false
+ - if:
+ properties:
+ fsl,burst-clk-enable: false
+ then:
+ properties:
+ fsl,continuous-burst-clk: false
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: fsl,imx1-weim
+ then:
+ patternProperties:
+ "^.*@[0-7],[0-9a-f]+$":
+ properties:
+ fsl,weim-cs-timing:
+ items:
+ items:
+ - description: CSxU
+ - description: CSxL
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - fsl,imx27-weim
+ - fsl,imx31-weim
+ - fsl,imx35-weim
+ then:
+ patternProperties:
+ "^.*@[0-7],[0-9a-f]+$":
+ properties:
+ fsl,weim-cs-timing:
+ items:
+ items:
+ - description: CSCRxU
+ - description: CSCRxL
+ - description: CSCRxA
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - fsl,imx50-weim
+ - fsl,imx51-weim
+ - fsl,imx6q-weim
+ - fsl,imx6sx-weim
+ - fsl,imx6ul-weim
+ then:
+ patternProperties:
+ "^.*@[0-7],[0-9a-f]+$":
+ properties:
+ fsl,weim-cs-timing:
+ items:
+ items:
+ - description: CSxGCR1
+ - description: CSxGCR2
+ - description: CSxRCR1
+ - description: CSxRCR2
+ - description: CSxWCR1
+ - description: CSxWCR2
+
+additionalProperties: false
+
+examples:
+ - |
+ memory-controller@21b8000 {
+ compatible = "fsl,imx6q-weim";
+ reg = <0x021b8000 0x4000>;
+ clocks = <&clks 196>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ fsl,weim-cs-gpr = <&gpr>;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x02000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ bank-width = <2>;
+ fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+ 0x0000c000 0x1404a38e 0x00000000>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
index 8d9dae15ade0..00deeb09f87d 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
@@ -37,5 +37,6 @@ allOf:
- $ref: ingenic,nemc-peripherals.yaml#
- $ref: intel,ixp4xx-expansion-peripheral-props.yaml#
- $ref: ti,gpmc-child.yaml#
+ - $ref: fsl/fsl,imx-weim-peripherals.yaml
additionalProperties: true
diff --git a/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt b/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
index b1f9474f36d5..f34a95611645 100644
--- a/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
+++ b/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
@@ -48,7 +48,7 @@ Example of usage:
-----------------
This example places the bridge on top of the i.MX WEIM parallel bus, see:
-Documentation/devicetree/bindings/bus/imx-weim.txt
+Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
&weim {
controller@0,0 {
--
2.43.0
Add compatibles used by different i.MX6 variants to the i.MX IOMUX
Controller GPR binding.
Signed-off-by: Sebastian Reichel <[email protected]>
---
.../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml | 18 +++++++++++++++++-
1 file changed, 17 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
index 1da1b758b4ae..8451cb4dd87c 100644
--- a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
+++ b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
@@ -17,7 +17,23 @@ properties:
compatible:
oneOf:
- items:
- - const: fsl,imx8mq-iomuxc-gpr
+ - enum:
+ - fsl,imx6q-iomuxc-gpr
+ - fsl,imx8mq-iomuxc-gpr
+ - const: syscon
+ - const: simple-mfd
+ - items:
+ - enum:
+ - fsl,imx6sl-iomuxc-gpr
+ - fsl,imx6sll-iomuxc-gpr
+ - fsl,imx6ul-iomuxc-gpr
+ - const: fsl,imx6q-iomuxc-gpr
+ - const: syscon
+ - items:
+ - enum:
+ - fsl,imx6sx-iomuxc-gpr
+ - fsl,imx7d-iomuxc-gpr
+ - const: fsl,imx6q-iomuxc-gpr
- const: syscon
- const: simple-mfd
- items:
--
2.43.0
Fix the following warning found via CHECK_DTBS:
tempmon: '#thermal-sensor-cells' is a required property
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 9eb4eee0c272..45b7605ac381 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -638,6 +638,7 @@ tempmon: tempmon {
nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
nvmem-cell-names = "calib", "temp_grade";
clocks = <&clks IMX6UL_CLK_PLL3_USB_OTG>;
+ #thermal-sensor-cells = <0>;
};
};
--
2.43.0
The nodename for a touchscreen should be touchscreen
instead of tsc.
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 45b7605ac381..8aa365f837ca 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -370,7 +370,7 @@ asrc: asrc@2034000 {
};
};
- tsc: tsc@2040000 {
+ tsc: touchscreen@2040000 {
compatible = "fsl,imx6ul-tsc";
reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
--
2.43.0
Fix WEIM node name in all i.MX SoC DT files.
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx1.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx27.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx31.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx35.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx51.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6sl.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6sx.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 2 +-
9 files changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx1.dtsi b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
index 1ac10965fdfd..389ecb1ebf8f 100644
--- a/arch/arm/boot/dts/nxp/imx/imx1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
@@ -251,7 +251,7 @@ gpio4: gpio@21c300 {
};
};
- weim: weim@220000 {
+ weim: memory-controller@220000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx1-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
index ec472695c71e..ec3ccc8f4095 100644
--- a/arch/arm/boot/dts/nxp/imx/imx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
@@ -568,7 +568,7 @@ nfc: nand-controller@d8000000 {
status = "disabled";
};
- weim: weim@d8002000 {
+ weim: memory-controller@d8002000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx27-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx31.dtsi b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
index e1ae7c175f7d..00006c90d9a7 100644
--- a/arch/arm/boot/dts/nxp/imx/imx31.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
@@ -352,7 +352,7 @@ nfc: nand@b8000000 {
status = "disabled";
};
- weim: weim@b8002000 {
+ weim: memory-controller@b8002000 {
compatible = "fsl,imx31-weim", "fsl,imx27-weim";
reg = <0xb8002000 0x1000>;
clocks = <&clks 56>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx35.dtsi b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
index 2d20e5541acc..442dc15677b8 100644
--- a/arch/arm/boot/dts/nxp/imx/imx35.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
@@ -374,7 +374,7 @@ nfc: nand@bb000000 {
status = "disabled";
};
- weim: weim@b8002000 {
+ weim: memory-controller@b8002000 {
#address-cells = <2>;
#size-cells = <1>;
clocks = <&clks 0>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx51.dtsi b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
index c96d6311dfa7..4efce49022e4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx51.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
@@ -578,7 +578,7 @@ m4if: m4if@83fd8000 {
reg = <0x83fd8000 0x1000>;
};
- weim: weim@83fda000 {
+ weim: memory-controller@83fda000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx51-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
index 81142c523fa8..8431b8a994f4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
@@ -1158,7 +1158,7 @@ mmdc1: memory-controller@21b4000 { /* MMDC1 */
status = "disabled";
};
- weim: weim@21b8000 {
+ weim: memory-controller@21b8000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx6q-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
index 28111efb19a6..6aa61235e39e 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
@@ -949,7 +949,7 @@ rngb: rngb@21b4000 {
clocks = <&clks IMX6SL_CLK_DUMMY>;
};
- weim: weim@21b8000 {
+ weim: memory-controller@21b8000 {
#address-cells = <2>;
#size-cells = <1>;
reg = <0x021b8000 0x4000>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
index df3a375f0a3e..0de359d62a47 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
@@ -1107,7 +1107,7 @@ fec2: ethernet@21b4000 {
status = "disabled";
};
- weim: weim@21b8000 {
+ weim: memory-controller@21b8000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx6sx-weim", "fsl,imx6q-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 8aa365f837ca..aeb7e07fd309 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -975,7 +975,7 @@ memory-controller@21b0000 {
clocks = <&clks IMX6UL_CLK_MMDC_P0_IPG>;
};
- weim: weim@21b8000 {
+ weim: memory-controller@21b8000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "fsl,imx6ul-weim", "fsl,imx6q-weim";
--
2.43.0
Add compatible value for i.MX6ULL based UNI-T
UTi260b thermal camera.
Signed-off-by: Sebastian Reichel <[email protected]>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 228dcc5c7d6f..7b65f9c9c1a5 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -708,6 +708,7 @@ properties:
- toradex,colibri-imx6ull # Colibri iMX6ULL Modules
- toradex,colibri-imx6ull-emmc # Colibri iMX6ULL 1GB (eMMC) Module
- toradex,colibri-imx6ull-wifi # Colibri iMX6ULL Wi-Fi / BT Modules
+ - uni-t,uti260b # UNI-T UTi260B Thermal Camera
- const: fsl,imx6ull
- description: i.MX6ULL Armadeus Systems OPOS6ULDev Board
--
2.43.0
Add UNI-T UTi260b thermal camera board.
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts | 572 ++++++++++++++++++
2 files changed, 573 insertions(+)
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a0..47350cf3ddeb 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -349,6 +349,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-tarragon-slavext.dtb \
imx6ull-tqma6ull2-mba6ulx.dtb \
imx6ull-tqma6ull2l-mba6ulx.dtb \
+ imx6ull-uti260b.dtb \
imx6ulz-14x14-evk.dtb \
imx6ulz-bsh-smm-m2.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
new file mode 100644
index 000000000000..2c0972145c79
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
@@ -0,0 +1,572 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2022-2024 Sebastian Reichel <[email protected]>
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "UNI-T UTi260B Thermal Camera";
+ compatible = "uni-t,uti260b", "fsl,imx6ull";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_led_ctrl>;
+
+ led {
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_FLASH;
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_gpio_keys>;
+ autorepeat;
+
+ up-key {
+ label = "Up";
+ gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_UP>;
+ };
+
+ down-key {
+ label = "Down";
+ gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_DOWN>;
+ };
+
+ left-key {
+ label = "Left";
+ gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LEFT>;
+ };
+
+ right-key {
+ label = "Right";
+ gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RIGHT>;
+ };
+
+ ok-key {
+ label = "Ok";
+ gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_ENTER>;
+ };
+
+ return-key {
+ label = "Return";
+ gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_ESC>;
+ };
+
+ play-key {
+ label = "Media";
+ gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MEDIA>;
+ };
+
+ trigger-key {
+ label = "Trigger";
+ gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_TRIGGER>;
+ };
+
+ power-key {
+ label = "Power";
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ };
+
+ light-key {
+ label = "Light";
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LIGHTS_TOGGLE>;
+ };
+ };
+
+ panel_backlight: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ enable-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_backlight_enable>;
+ power-supply = <®_vsd>;
+ pwms = <&pwm1 0 50000 0>;
+ };
+
+ reg_vsd: regulator-vsd {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_vref: regulator-vref-4v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "VREF_4V2";
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+ };
+
+ tp5000: charger {
+ compatible = "gpio-charger";
+ charger-type = "usb-sdp";
+ gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_charger_stat1>;
+ };
+
+ battery: battery {
+ compatible = "simple-battery";
+ /* generic 26650 battery */
+ device-chemistry = "lithium-ion";
+ charge-full-design-microamp-hours = <5000000>;
+ voltage-max-design-microvolt = <4200000>;
+ voltage-min-design-microvolt = <3300000>;
+ };
+
+ fuel-gauge {
+ compatible = "adc-battery";
+ charged-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ io-channel-names = "voltage";
+ io-channels = <&adc1 7>;
+ monitored-battery = <&battery>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_charger_stat2>;
+ power-supplies = <&tp5000>;
+ };
+
+ poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_poweroff>;
+ };
+};
+
+&gpio1 {
+ ir-reset-hog {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ line-name = "ir-reset-gpio";
+ output-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_ir_reset>;
+ };
+};
+
+&gpio2 {
+ /* configuring this to output-high results in poweroff */
+ power-en-hog {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ line-name = "power-en-gpio";
+ output-low;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_poweroff2>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_spi3>, <&mux_spi3_cs>;
+ status = "okay";
+
+ panel@0 {
+ compatible = "inanbo,t28cp45tn89-v17";
+ reg = <0>;
+ backlight = <&panel_backlight>;
+ power-supply = <®_vsd>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <1000000>;
+ spi-rx-bus-width = <0>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_uart>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_pwm>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_i2c1>;
+ status = "okay";
+
+ camera@21 {
+ compatible = "galaxycore,gc0308";
+ reg = <0x21>;
+ clocks = <&clks IMX6UL_CLK_CSI>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_gc0308>;
+ powerdown-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ vdd28-supply = <®_vsd>;
+
+ port {
+ gc0308_to_parallel: endpoint {
+ remote-endpoint = <¶llel_from_gc0308>;
+ bus-width = <8>;
+ data-shift = <2>; /* lines 9:2 are used */
+ hsync-active = <1>; /* active high */
+ vsync-active = <1>; /* active high */
+ data-active = <1>; /* active high */
+ pclk-sample = <1>; /* sample on rising edge */
+ };
+ };
+ };
+};
+
+&csi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_csi>;
+
+ port {
+ parallel_from_gc0308: endpoint {
+ remote-endpoint = <&gc0308_to_parallel>;
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_i2c2>;
+ status = "okay";
+
+ rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+&lcdif {
+ assigned-clocks = <&clks IMX6UL_CLK_LCDIF_PRE_SEL>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL5_VIDEO_DIV>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_lcd_data>, <&mux_lcd_ctrl>;
+ status = "okay";
+
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+};
+
+&usdhc1 {
+ /* MicroSD */
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ no-1-8-v;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&mux_sdhc1>, <&mux_sdhc1_cd>;
+ pinctrl-1 = <&mux_sdhc1_100mhz>, <&mux_sdhc1_cd>;
+ pinctrl-2 = <&mux_sdhc1_200mhz>, <&mux_sdhc1_cd>;
+ wakeup-source;
+ vmmc-supply = <®_vsd>;
+ status = "okay";
+};
+
+&usdhc2 {
+ /* eMMC */
+ keep-power-in-suspend;
+ no-1-8-v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_sdhc2>;
+ wakeup-source;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_wdog>;
+};
+
+&adc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mux_adc>;
+ vref-supply = <®_vref>;
+ #io-channel-cells = <1>;
+ status = "okay";
+};
+
+&usbotg1 {
+ /* USB-C connector */
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbotg2 {
+ /* thermal sensor */
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <106>;
+};
+
+&iomuxc {
+ mux_ir_reset: irresetgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x3008
+ >;
+ };
+
+ mux_poweroff: poweroffgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04 0x3008
+ >;
+ };
+
+ mux_poweroff2: poweroff2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_TX_CLK__GPIO2_IO06 0x3008
+ >;
+ };
+
+ mux_charger_stat1: charger1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x3008
+ >;
+ };
+
+ mux_charger_stat2: charger2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x3008
+ >;
+ };
+
+ mux_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
+
+ mux_sdhc1_cd: sdhc1-cd-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ mux_sdhc1: sdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ >;
+ };
+
+ mux_sdhc1_100mhz: sdhc1-100mhz-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x170b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ mux_sdhc1_200mhz: sdhc1-200mhz-grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x170f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ mux_sdhc2: sdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+ >;
+ };
+
+ mux_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ mux_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001f8a8
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001f8a8
+ >;
+ };
+
+ mux_uart: uartgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ mux_gpio_keys: gpiokeygrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x3008
+ MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x3008
+ MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x3008
+ MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x3008
+ MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x3008
+ MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x3008
+ MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x3008
+ MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x3008
+ MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03 0x3008
+ MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01 0x3008
+ >;
+ };
+
+ mux_led_ctrl: ledctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02 0x3008
+ >;
+ };
+
+ mux_adc: adcgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__GPIO1_IO07 0xb0
+ >;
+ };
+
+ mux_pwm: pwm1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
+ >;
+ };
+
+ mux_backlight_enable: blenablegrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x3008
+ >;
+ };
+
+ mux_lcd_data: lcdifdatgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
+ >;
+ };
+
+ mux_lcd_ctrl: lcdifctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
+ >;
+ };
+
+ mux_csi: csi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
+ MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
+ MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088
+ MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088
+ MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088
+ MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088
+ MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088
+ MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088
+ MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088
+ MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088
+ MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088
+ >;
+ };
+
+ mux_gc0308: gc0308grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1e038
+ MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x1b088
+ MX6UL_PAD_GPIO1_IO06__GPIO1_IO06 0x1b088
+ >;
+ };
+
+
+ mux_spi3: ecspi3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x100b1
+ MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x100b1
+ >;
+ };
+
+ mux_spi3_cs: ecspi3_csgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x3008
+ >;
+ };
+};
--
2.43.0
Convert the i.MX6UL touchscreen DT binding to YAML.
Signed-off-by: Sebastian Reichel <[email protected]>
---
.../input/touchscreen/fsl,imx6ul-tsc.yaml | 97 +++++++++++++++++++
.../bindings/input/touchscreen/imx6ul_tsc.txt | 38 --------
2 files changed, 97 insertions(+), 38 deletions(-)
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml b/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
new file mode 100644
index 000000000000..678756ad0f92
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/fsl,imx6ul-tsc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX6UL Touch Controller
+
+maintainers:
+ - Haibo Chen <[email protected]>
+ - Shawn Guo <[email protected]>
+ - Sascha Hauer <[email protected]>
+
+properties:
+ compatible:
+ const: fsl,imx6ul-tsc
+
+ reg:
+ items:
+ - description: touch controller address
+ - description: ADC2 address
+
+ interrupts:
+ items:
+ - description: touch controller address
+ - description: ADC2 address
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: tsc
+ - const: adc
+
+ xnur-gpios:
+ maxItems: 1
+ description:
+ The X- gpio this controller connect to. This xnur-gpio returns to
+ low once the finger leave the touch screen (The last touch event
+ the touch controller capture).
+
+ measure-delay-time:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The value of measure delay time. Before X-axis or Y-axis measurement,
+ the screen need some time before even potential distribution ready.
+ default: 0xffff
+ minimum: 0
+ maximum: 0xffffff
+
+ pre-charge-time:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The touch screen need some time to precharge.
+ default: 0xfff
+ minimum: 0
+ maximum: 0xffffffff
+
+ touchscreen-average-samples:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Number of data samples which are averaged for each read.
+ enum: [ 1, 4, 8, 16, 32 ]
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - xnur-gpios
+
+allOf:
+ - $ref: touchscreen.yaml#
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/imx6ul-clock.h>
+ #include <dt-bindings/gpio/gpio.h>
+ touchscreen@2040000 {
+ compatible = "fsl,imx6ul-tsc";
+ reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_IPG>,
+ <&clks IMX6UL_CLK_ADC2>;
+ clock-names = "tsc", "adc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ measure-delay-time = <0xfff>;
+ pre-charge-time = <0xffff>;
+ touchscreen-average-samples = <32>;
+ };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
deleted file mode 100644
index 164915004424..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-* Freescale i.MX6UL Touch Controller
-
-Required properties:
-- compatible: must be "fsl,imx6ul-tsc".
-- reg: this touch controller address and the ADC2 address.
-- interrupts: the interrupt of this touch controller and ADC2.
-- clocks: the root clock of touch controller and ADC2.
-- clock-names; must be "tsc" and "adc".
-- xnur-gpio: the X- gpio this controller connect to.
- This xnur-gpio returns to low once the finger leave the touch screen (The
- last touch event the touch controller capture).
-
-Optional properties:
-- measure-delay-time: the value of measure delay time.
- Before X-axis or Y-axis measurement, the screen need some time before
- even potential distribution ready.
- This value depends on the touch screen.
-- pre-charge-time: the touch screen need some time to precharge.
- This value depends on the touch screen.
-- touchscreen-average-samples: Number of data samples which are averaged for
- each read. Valid values are 1, 4, 8, 16 and 32.
-
-Example:
- tsc: tsc@2040000 {
- compatible = "fsl,imx6ul-tsc";
- reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_IPG>,
- <&clks IMX6UL_CLK_ADC2>;
- clock-names = "tsc", "adc";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
- measure-delay-time = <0xfff>;
- pre-charge-time = <0xffff>;
- touchscreen-average-samples = <32>;
- };
--
2.43.0
Replace all "xnur-gpio" with "xnur-gpios" in the
i.MX6UL(L) Touchscreen node.
Signed-off-by: Sebastian Reichel <[email protected]>
---
arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi | 2 +-
arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi | 2 +-
4 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
index 2ac40d69425b..f10f0525490b 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
@@ -321,7 +321,7 @@ &snvs_pwrkey {
&tsc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
measure-delay-time = <0xffff>;
pre-charge-time = <0xfff>;
status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
index 875ae699c5cb..2ca18f3dad0a 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
@@ -203,7 +203,7 @@ &pwm8 {
&tsc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
};
&sai2 {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
index 18cac19aa9b0..af337f18a266 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
@@ -156,7 +156,7 @@ &snvs_pwrkey {
&tsc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
measure-delay-time = <0xffff>;
pre-charge-time = <0xffff>;
status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
index 830b5a5064f2..6d2163250b5d 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
@@ -273,7 +273,7 @@ &tsc {
pinctrl-names = "default";
pre-charge-time = <0xfff>;
touchscreen-average-samples = <32>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
};
/* DHCOM UART1 */
--
2.43.0
Uni-Trend Technology is a manufacturer of measurement
and testing tools.
Acked-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 1a0dc04f1db4..e945e76696c2 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1484,6 +1484,8 @@ patternProperties:
description: Ufi Space Co., Ltd.
"^ugoos,.*":
description: Ugoos Industrial Co., Ltd.
+ "^uni-t,.*":
+ description: Uni-Trend Technology (China) Co., Ltd.
"^uniwest,.*":
description: United Western Technologies Corp (UniWest)
"^upisemi,.*":
--
2.43.0
On Tue, 13 Feb 2024 02:00:51 +0100, Sebastian Reichel wrote:
> Convert the i.MX Wireless External Interface Module binding to YAML.
>
> Signed-off-by: Sebastian Reichel <[email protected]>
> ---
> .../devicetree/bindings/bus/imx-weim.txt | 117 ----------
> .../fsl/fsl,imx-weim-peripherals.yaml | 36 ++++
> .../memory-controllers/fsl/fsl,imx-weim.yaml | 201 ++++++++++++++++++
> .../mc-peripheral-props.yaml | 1 +
> .../fieldbus/arcx,anybus-controller.txt | 2 +-
> 5 files changed, 239 insertions(+), 118 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
> create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
> create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/bus/socionext,uniphier-system-bus.example.dtb: serial@5,200000: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/serial/8250.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-bus-controller.example.dtb: flash@0,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-bus-controller.example.dtb: serial@1,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/serial/8250.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-bus-controller.example.dtb: serial@1,0: Unevaluated properties are not allowed ('intel,ixp4xx-eb-byte-access', 'intel,ixp4xx-eb-cycle-type', 'intel,ixp4xx-eb-t3', 'intel,ixp4xx-eb-write-enable' were unexpected)
from schema $id: http://devicetree.org/schemas/serial/8250.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,ifc.example.dtb: flash@0,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.example.dtb: memory-controller@13410000: ethernet@6: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/memory-controllers/ingenic,nemc.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.example.dtb: ethernet@6: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/net/davicom,dm9000.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/ingenic,nemc.example.dtb: ethernet@6: Unevaluated properties are not allowed ('ingenic,nemc-tAH', 'ingenic,nemc-tAS', 'ingenic,nemc-tAW', 'ingenic,nemc-tBP', 'ingenic,nemc-tSTRV' were unexpected)
from schema $id: http://devicetree.org/schemas/net/davicom,dm9000.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.example.dtb: memory-controller@58002000: psram@0,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.example.dtb: memory-controller@58002000: nand-controller@4,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.example.dtb: psram@0,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/watchdog/maxim,max63xx.example.dtb: watchdog@50000000: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/watchdog/maxim,max63xx.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/serial/serial.example.dtb: serial@1234: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/serial/8250.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/serial/8250.example.dtb: serial@80230000: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/serial/8250.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/serial/8250.example.dtb: serial@49042000: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/serial/8250.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/serial/8250.example.dtb: serial@1e787000: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/serial/8250.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/davicom,dm9000.example.dtb: ethernet@a8000000: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/net/davicom,dm9000.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/micrel,ks8851.example.dtb: ethernet@1,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/net/micrel,ks8851.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.example.dtb: memory-controller@47034000: flash@0,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/ti,am654-hbmc.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/ti,am654-hbmc.example.dtb: flash@0,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/mtd-physmap.example.dtb: flash@ff000000: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/mtd-physmap.example.dtb: flash@0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/mtd-physmap.example.dtb: sram@2,0: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/mtd-physmap.example.dtb: flash@20000000: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/ingenic,nand.example.dtb: memory-controller@13410000: nand-controller@1: 'fsl,weim-cs-timing' is a required property
from schema $id: http://devicetree.org/schemas/memory-controllers/ingenic,nemc.yaml#
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
On 13/02/2024 02:01, Sebastian Reichel wrote:
> Add compatible value for i.MX6ULL based UNI-T
> UTi260b thermal camera.
>
> Signed-off-by: Sebastian Reichel <[email protected]>
> ---
Acked-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
On Tue, Feb 13, 2024 at 02:00:51AM +0100, Sebastian Reichel wrote:
> Convert the i.MX Wireless External Interface Module binding to YAML.
>
> Signed-off-by: Sebastian Reichel <[email protected]>
> ---
> .../devicetree/bindings/bus/imx-weim.txt | 117 ----------
> .../fsl/fsl,imx-weim-peripherals.yaml | 36 ++++
> .../memory-controllers/fsl/fsl,imx-weim.yaml | 201 ++++++++++++++++++
> .../mc-peripheral-props.yaml | 1 +
> .../fieldbus/arcx,anybus-controller.txt | 2 +-
> 5 files changed, 239 insertions(+), 118 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
> create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
> create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
> diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
> new file mode 100644
> index 000000000000..86d7e5011107
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
> @@ -0,0 +1,36 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: i.MX WEIM Bus Peripheral Nodes
> +
> +maintainers:
> + - Shawn Guo <[email protected]>
> + - Sascha Hauer <[email protected]>
> +
> +description:
> + This binding is meant for the child nodes of the WEIM node. The node
> + represents any device connected to the WEIM bus. It may be a Flash chip,
> + RAM chip or Ethernet controller, etc. These properties are meant for
> + configuring the WEIM settings/timings and will accompany the bindings
> + supported by the respective device.
> +
> +properties:
> + reg: true
> +
> + fsl,weim-cs-timing:
> + $ref: /schemas/types.yaml#/definitions/uint32-array
> + description:
> + Timing values for the child node.
> + minItems: 2
> + maxItems: 6
> +
> +required:
> + - compatible
> + - reg
> + - fsl,weim-cs-timing
This should be marked required in fsl,imx-weim.yaml instead to fix the
errors.
Really, the other required ones should be in mc-peripheral-props.yaml as
it applies to everyone.
> +
> +# the WEIM child will have its own native properties
> +additionalProperties: true
On Mon, Feb 12, 2024 at 10:03 PM Sebastian Reichel <[email protected]> wrote:
>
> Replace all "xnur-gpio" with "xnur-gpios" in the
> i.MX6UL(L) Touchscreen node.
Please explain the reason for doing this.
Am 13.02.24 um 02:01 schrieb Sebastian Reichel:
> Add UNI-T UTi260b thermal camera board.
>
> Signed-off-by: Sebastian Reichel <[email protected]>
Reviewed-by: Stefan Wahren <[email protected]>
On Tue, 13 Feb 2024 02:00:49 +0100, Sebastian Reichel wrote:
> This adds adds support for the UNI-T UTi260B thermal camera, which is based
> on i.MX6ULL. Patches 1-14 clean up all warnings reported by CHECK_DTBS for
> i.MX6ULL (i.e. for an empty board). They are not specific to the UTi260B and
> in fact that machine has most of the IP handled by these patches marked as
> disabled. Then patches 15+16 introduce the vendor and board compatible DT
> bindings. Finally the last patches adds support for the thermal camera itself.
>
> [...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[03/17] ASoC: dt-bindings: fsl,imx-asrc: convert to YAML
commit: 20c0c9b352df1ab7915c827cb1d182bfc32f9f46
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
Hi,
On Tue, Feb 13, 2024 at 10:53:05AM -0300, Fabio Estevam wrote:
> On Mon, Feb 12, 2024 at 10:03 PM Sebastian Reichel <[email protected]> wrote:
> > Replace all "xnur-gpio" with "xnur-gpios" in the
> > i.MX6UL(L) Touchscreen node.
>
> Please explain the reason for doing this.
DT binding maintainers asked to use xnur-gpios instead of xnur-gpio
in the DT binding when converting to YAML (the -gpio suffix is
deprecated in favour of -gpios). This updates the DT files to become
compliant. The Linux kernel driver has already been using gpiod API
when it was added to the kernel, so this change is backwards compatible.
I will extend the description from this patch in v3.
-- Sebastian
On Tue, 13 Feb 2024 02:00:53 +0100, Sebastian Reichel wrote:
> Convert the i.MX6UL touchscreen DT binding to YAML.
>
> Signed-off-by: Sebastian Reichel <[email protected]>
> ---
> .../input/touchscreen/fsl,imx6ul-tsc.yaml | 97 +++++++++++++++++++
> .../bindings/input/touchscreen/imx6ul_tsc.txt | 38 --------
> 2 files changed, 97 insertions(+), 38 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
> delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
>
Reviewed-by: Rob Herring <[email protected]>
On Tue, Feb 13, 2024 at 02:00:55AM +0100, Sebastian Reichel wrote:
> Add compatibles used by different i.MX6 variants to the i.MX IOMUX
> Controller GPR binding.
>
> Signed-off-by: Sebastian Reichel <[email protected]>
> ---
> .../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml | 18 +++++++++++++++++-
> 1 file changed, 17 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
> index 1da1b758b4ae..8451cb4dd87c 100644
> --- a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
> +++ b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
> @@ -17,7 +17,23 @@ properties:
> compatible:
> oneOf:
> - items:
> - - const: fsl,imx8mq-iomuxc-gpr
> + - enum:
> + - fsl,imx6q-iomuxc-gpr
> + - fsl,imx8mq-iomuxc-gpr
> + - const: syscon
> + - const: simple-mfd
> + - items:
> + - enum:
> + - fsl,imx6sl-iomuxc-gpr
> + - fsl,imx6sll-iomuxc-gpr
> + - fsl,imx6ul-iomuxc-gpr
> + - const: fsl,imx6q-iomuxc-gpr
> + - const: syscon
A bit odd that imx6q is a simple-mfd above, but not here. I suppose
that could be valid if the variants here don't have sub-devices or they
do, but have a dependency on the parent.
Acked-by: Rob Herring <[email protected]>
> + - items:
> + - enum:
> + - fsl,imx6sx-iomuxc-gpr
> + - fsl,imx7d-iomuxc-gpr
> + - const: fsl,imx6q-iomuxc-gpr
> - const: syscon
> - const: simple-mfd
> - items:
> --
> 2.43.0
>
Hi,
On Thu, Feb 15, 2024 at 08:55:20AM -0600, Rob Herring wrote:
> On Tue, Feb 13, 2024 at 02:00:55AM +0100, Sebastian Reichel wrote:
> > Add compatibles used by different i.MX6 variants to the i.MX IOMUX
> > Controller GPR binding.
> >
> > Signed-off-by: Sebastian Reichel <[email protected]>
> > ---
> > .../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml | 18 +++++++++++++++++-
> > 1 file changed, 17 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
> > index 1da1b758b4ae..8451cb4dd87c 100644
> > --- a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
> > +++ b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
> > @@ -17,7 +17,23 @@ properties:
> > compatible:
> > oneOf:
> > - items:
> > - - const: fsl,imx8mq-iomuxc-gpr
> > + - enum:
> > + - fsl,imx6q-iomuxc-gpr
> > + - fsl,imx8mq-iomuxc-gpr
> > + - const: syscon
> > + - const: simple-mfd
> > + - items:
> > + - enum:
> > + - fsl,imx6sl-iomuxc-gpr
> > + - fsl,imx6sll-iomuxc-gpr
> > + - fsl,imx6ul-iomuxc-gpr
> > + - const: fsl,imx6q-iomuxc-gpr
> > + - const: syscon
>
> A bit odd that imx6q is a simple-mfd above, but not here. I suppose
> that could be valid if the variants here don't have sub-devices or they
> do, but have a dependency on the parent.
These do not have sub-nodes, while the other instances have.
> Acked-by: Rob Herring <[email protected]>
Thanks,
-- Sebastian
On Tue, Feb 13, 2024 at 02:00:53AM +0100, Sebastian Reichel wrote:
> Convert the i.MX6UL touchscreen DT binding to YAML.
>
> Signed-off-by: Sebastian Reichel <[email protected]>
Applied, thank you.
--
Dmitry
Hello Dmitry,
On Sat, Mar 09, 2024 at 05:34:59PM -0800, Dmitry Torokhov wrote:
> On Tue, Feb 13, 2024 at 02:00:53AM +0100, Sebastian Reichel wrote:
> > Convert the i.MX6UL touchscreen DT binding to YAML.
> >
> > Signed-off-by: Sebastian Reichel <[email protected]>
>
> Applied, thank you.
Rob send a message, that he applied all DT binding patches from this
series (incl. this one) at the same time you asked how it should be
handled:
Message from Rob (Tue, 5 Mar 2024 11:34:32 -0600)
https://lore.kernel.org/all/[email protected]/
Message from You (Tue, 5 Mar 2024 09:30:47 -0800)
https://lore.kernel.org/all/[email protected]/
I assumed, that you would see Rob's message and thus did not bother
to reply. Obviously I was wrong, sorry about that.
Greetings,
-- Sebastian
On Sun, Mar 10, 2024 at 04:07:06PM +0100, Sebastian Reichel wrote:
> Hello Dmitry,
>
> On Sat, Mar 09, 2024 at 05:34:59PM -0800, Dmitry Torokhov wrote:
> > On Tue, Feb 13, 2024 at 02:00:53AM +0100, Sebastian Reichel wrote:
> > > Convert the i.MX6UL touchscreen DT binding to YAML.
> > >
> > > Signed-off-by: Sebastian Reichel <[email protected]>
> >
> > Applied, thank you.
>
> Rob send a message, that he applied all DT binding patches from this
> series (incl. this one) at the same time you asked how it should be
> handled:
>
> Message from Rob (Tue, 5 Mar 2024 11:34:32 -0600)
> https://lore.kernel.org/all/[email protected]/
>
> Message from You (Tue, 5 Mar 2024 09:30:47 -0800)
> https://lore.kernel.org/all/[email protected]/
>
> I assumed, that you would see Rob's message and thus did not bother
> to reply. Obviously I was wrong, sorry about that.
Oh, my bad, I'll drop the patch from my tree. Thank you for pointing
this out.
--
Dmitry