Provide thermal zone to read thermal sensor in the SoC. We can read all the
thermal sensors value in the SoC by the node /sys/class/thermal/
In mtk_thermal_bank_temperature, return -EAGAIN instead of -EACCESS
on the first read of sensor that often are bogus values.
This can avoid following warning on boot:
thermal thermal_zone6: failed to read out thermal zone (-13)
Signed-off-by: Michael Kao <[email protected]>
Signed-off-by: Hsin-Yi Wang <[email protected]>
Signed-off-by: Amjad Ouled-Ameur <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
---
drivers/thermal/mtk_thermal.c | 99 ++++++++++++++++++++++++++++++++-----------
1 file changed, 74 insertions(+), 25 deletions(-)
diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index 3a5df1440822..b1f4d19edd4f 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -259,6 +259,11 @@ enum mtk_thermal_version {
struct mtk_thermal;
+struct mtk_thermal_zone {
+ struct mtk_thermal *mt;
+ int id;
+};
+
struct thermal_bank_cfg {
unsigned int num_sensors;
const int *sensors;
@@ -307,6 +312,8 @@ struct mtk_thermal {
const struct mtk_thermal_data *conf;
struct mtk_thermal_bank banks[MAX_NUM_ZONES];
+
+ int (*raw_to_mcelsius)(struct mtk_thermal *mt, int sensno, s32 raw);
};
/* MT8183 thermal sensor data */
@@ -709,6 +716,29 @@ static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
mutex_unlock(&mt->lock);
}
+static int _get_sensor_temp(struct mtk_thermal *mt, int id)
+{
+ u32 raw;
+ int temp;
+
+ const struct mtk_thermal_data *conf = mt->conf;
+
+ raw = readl(mt->thermal_base + conf->msr[id]);
+
+ temp = mt->raw_to_mcelsius(mt, id, raw);
+
+ /*
+ * The first read of a sensor often contains very high bogus
+ * temperature value. Filter these out so that the system does
+ * not immediately shut down.
+ */
+
+ if (temp > 200000)
+ return -EAGAIN;
+ else
+ return temp;
+}
+
/**
* mtk_thermal_bank_temperature - get the temperature of a bank
* @bank: The bank
@@ -721,26 +751,9 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
struct mtk_thermal *mt = bank->mt;
const struct mtk_thermal_data *conf = mt->conf;
int i, temp = INT_MIN, max = INT_MIN;
- u32 raw;
for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
- raw = readl(mt->thermal_base + conf->msr[i]);
-
- if (mt->conf->version == MTK_THERMAL_V1) {
- temp = raw_to_mcelsius_v1(
- mt, conf->bank_data[bank->id].sensors[i], raw);
- } else {
- temp = raw_to_mcelsius_v2(
- mt, conf->bank_data[bank->id].sensors[i], raw);
- }
-
- /*
- * The first read of a sensor often contains very high bogus
- * temperature value. Filter these out so that the system does
- * not immediately shut down.
- */
- if (temp > 200000)
- temp = 0;
+ temp = _get_sensor_temp(mt, i);
if (temp > max)
max = temp;
@@ -749,9 +762,10 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
return max;
}
-static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
+static int mtk_read_temp(struct thermal_zone_device *tzdev, int *temperature)
{
- struct mtk_thermal *mt = tz->devdata;
+ struct mtk_thermal_zone *tz = tzdev->devdata;
+ struct mtk_thermal *mt = tz->mt;
int i;
int tempmax = INT_MIN;
@@ -770,10 +784,28 @@ static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
return 0;
}
+static int mtk_read_sensor_temp(struct thermal_zone_device *tzdev, int *temperature)
+{
+ struct mtk_thermal_zone *tz = tzdev->devdata;
+ struct mtk_thermal *mt = tz->mt;
+ int id = tz->id - 1;
+
+ if (id < 0)
+ return -EACCES;
+
+ *temperature = _get_sensor_temp(mt, id);
+
+ return 0;
+}
+
static const struct thermal_zone_device_ops mtk_thermal_ops = {
.get_temp = mtk_read_temp,
};
+static const struct thermal_zone_device_ops mtk_thermal_sensor_ops = {
+ .get_temp = mtk_read_sensor_temp,
+};
+
static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
u32 apmixed_phys_base, u32 auxadc_phys_base,
int ctrl_id)
@@ -1072,6 +1104,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
u64 auxadc_phys_base, apmixed_phys_base;
struct thermal_zone_device *tzdev;
void __iomem *apmixed_base, *auxadc_base;
+ struct mtk_thermal_zone *tz;
mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
if (!mt)
@@ -1150,6 +1183,9 @@ static int mtk_thermal_probe(struct platform_device *pdev)
mtk_thermal_turn_on_buffer(mt, apmixed_base);
+ mt->raw_to_mcelsius = (mt->conf->version == MTK_THERMAL_V1) ?
+ raw_to_mcelsius_v1 : raw_to_mcelsius_v2;
+
if (mt->conf->version == MTK_THERMAL_V2) {
mtk_thermal_release_periodic_ts(mt, auxadc_base);
}
@@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, mt);
- tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
- &mtk_thermal_ops);
- if (IS_ERR(tzdev)) {
- ret = PTR_ERR(tzdev);
- goto err_disable_clk_peri_therm;
+ for (i = 0; i < mt->conf->num_sensors + 1; i++) {
+ tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
+ if (!tz)
+ return -ENOMEM;
+
+ tz->mt = mt;
+ tz->id = i;
+
+ tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
+ &mtk_thermal_ops :
+ &mtk_thermal_sensor_ops);
+
+ if (IS_ERR(tzdev)) {
+ ret = PTR_ERR(tzdev);
+ if (ret == -ENODEV)
+ continue;
+ goto err_disable_clk_peri_therm;
+ }
}
ret = devm_thermal_add_hwmon_sysfs(tzdev);
--
b4 0.10.1
On 18/11/2022 12:04, Amjad Ouled-Ameur wrote:
> Provide thermal zone to read thermal sensor in the SoC. We can read all the
> thermal sensors value in the SoC by the node /sys/class/thermal/
>
> In mtk_thermal_bank_temperature, return -EAGAIN instead of -EACCESS
> on the first read of sensor that often are bogus values.
> This can avoid following warning on boot:
>
> thermal thermal_zone6: failed to read out thermal zone (-13)
>
> Signed-off-by: Michael Kao <[email protected]>
> Signed-off-by: Hsin-Yi Wang <[email protected]>
> Signed-off-by: Amjad Ouled-Ameur <[email protected]>
> Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
> ---
> drivers/thermal/mtk_thermal.c | 99 ++++++++++++++++++++++++++++++++-----------
> 1 file changed, 74 insertions(+), 25 deletions(-)
>
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> index 3a5df1440822..b1f4d19edd4f 100644
> --- a/drivers/thermal/mtk_thermal.c
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -259,6 +259,11 @@ enum mtk_thermal_version {
>
> struct mtk_thermal;
>
> +struct mtk_thermal_zone {
> + struct mtk_thermal *mt;
> + int id;
> +};
> +
> struct thermal_bank_cfg {
> unsigned int num_sensors;
> const int *sensors;
> @@ -307,6 +312,8 @@ struct mtk_thermal {
>
> const struct mtk_thermal_data *conf;
> struct mtk_thermal_bank banks[MAX_NUM_ZONES];
> +
> + int (*raw_to_mcelsius)(struct mtk_thermal *mt, int sensno, s32 raw);
> };
>
> /* MT8183 thermal sensor data */
> @@ -709,6 +716,29 @@ static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
> mutex_unlock(&mt->lock);
> }
>
> +static int _get_sensor_temp(struct mtk_thermal *mt, int id)
> +{
> + u32 raw;
> + int temp;
> +
> + const struct mtk_thermal_data *conf = mt->conf;
> +
> + raw = readl(mt->thermal_base + conf->msr[id]);
> +
> + temp = mt->raw_to_mcelsius(mt, id, raw);
> +
> + /*
> + * The first read of a sensor often contains very high bogus
> + * temperature value. Filter these out so that the system does
> + * not immediately shut down.
> + */
> +
> + if (temp > 200000)
> + return -EAGAIN;
> + else
> + return temp;
> +}
> +
> /**
> * mtk_thermal_bank_temperature - get the temperature of a bank
> * @bank: The bank
> @@ -721,26 +751,9 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> struct mtk_thermal *mt = bank->mt;
> const struct mtk_thermal_data *conf = mt->conf;
> int i, temp = INT_MIN, max = INT_MIN;
> - u32 raw;
>
> for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
> - raw = readl(mt->thermal_base + conf->msr[i]);
> -
> - if (mt->conf->version == MTK_THERMAL_V1) {
> - temp = raw_to_mcelsius_v1(
> - mt, conf->bank_data[bank->id].sensors[i], raw);
> - } else {
> - temp = raw_to_mcelsius_v2(
> - mt, conf->bank_data[bank->id].sensors[i], raw);
> - }
> -
> - /*
> - * The first read of a sensor often contains very high bogus
> - * temperature value. Filter these out so that the system does
> - * not immediately shut down.
> - */
> - if (temp > 200000)
> - temp = 0;
> + temp = _get_sensor_temp(mt, i);
>
> if (temp > max)
> max = temp;
> @@ -749,9 +762,10 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> return max;
> }
>
> -static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
> +static int mtk_read_temp(struct thermal_zone_device *tzdev, int *temperature)
> {
> - struct mtk_thermal *mt = tz->devdata;
> + struct mtk_thermal_zone *tz = tzdev->devdata;
> + struct mtk_thermal *mt = tz->mt;
> int i;
> int tempmax = INT_MIN;
>
> @@ -770,10 +784,28 @@ static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
> return 0;
> }
>
> +static int mtk_read_sensor_temp(struct thermal_zone_device *tzdev, int *temperature)
> +{
> + struct mtk_thermal_zone *tz = tzdev->devdata;
> + struct mtk_thermal *mt = tz->mt;
> + int id = tz->id - 1;
> +
> + if (id < 0)
> + return -EACCES;
> +
> + *temperature = _get_sensor_temp(mt, id);
> +
> + return 0;
> +}
> +
> static const struct thermal_zone_device_ops mtk_thermal_ops = {
> .get_temp = mtk_read_temp,
> };
>
> +static const struct thermal_zone_device_ops mtk_thermal_sensor_ops = {
> + .get_temp = mtk_read_sensor_temp,
> +};
> +
> static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
> u32 apmixed_phys_base, u32 auxadc_phys_base,
> int ctrl_id)
> @@ -1072,6 +1104,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> u64 auxadc_phys_base, apmixed_phys_base;
> struct thermal_zone_device *tzdev;
> void __iomem *apmixed_base, *auxadc_base;
> + struct mtk_thermal_zone *tz;
>
> mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
> if (!mt)
> @@ -1150,6 +1183,9 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>
> mtk_thermal_turn_on_buffer(mt, apmixed_base);
>
> + mt->raw_to_mcelsius = (mt->conf->version == MTK_THERMAL_V1) ?
> + raw_to_mcelsius_v1 : raw_to_mcelsius_v2;
> +
> if (mt->conf->version == MTK_THERMAL_V2) {
> mtk_thermal_release_periodic_ts(mt, auxadc_base);
> }
> @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>
> platform_set_drvdata(pdev, mt);
>
> - tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
> - &mtk_thermal_ops);
> - if (IS_ERR(tzdev)) {
> - ret = PTR_ERR(tzdev);
> - goto err_disable_clk_peri_therm;
> + for (i = 0; i < mt->conf->num_sensors + 1; i++) {
> + tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
> + if (!tz)
> + return -ENOMEM;
> +
> + tz->mt = mt;
> + tz->id = i;
> +
> + tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
> + &mtk_thermal_ops :
> + &mtk_thermal_sensor_ops);
Here you use again the aggregation
> +
> + if (IS_ERR(tzdev)) {
> + ret = PTR_ERR(tzdev);
> + if (ret == -ENODEV)
> + continue;
> + goto err_disable_clk_peri_therm;
> + }
> }
>
> ret = devm_thermal_add_hwmon_sysfs(tzdev);
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
Hi Daniel,
On Sun Dec 4, 2022 at 6:26 PM CET, Daniel Lezcano wrote:
> On 18/11/2022 12:04, Amjad Ouled-Ameur wrote:
> > Provide thermal zone to read thermal sensor in the SoC. We can read all the
> > thermal sensors value in the SoC by the node /sys/class/thermal/
> >
> > In mtk_thermal_bank_temperature, return -EAGAIN instead of -EACCESS
> > on the first read of sensor that often are bogus values.
> > This can avoid following warning on boot:
> >
> > thermal thermal_zone6: failed to read out thermal zone (-13)
> >
> > Signed-off-by: Michael Kao <[email protected]>
> > Signed-off-by: Hsin-Yi Wang <[email protected]>
> > Signed-off-by: Amjad Ouled-Ameur <[email protected]>
> > Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
> > ---
> > drivers/thermal/mtk_thermal.c | 99 ++++++++++++++++++++++++++++++++-----------
> > 1 file changed, 74 insertions(+), 25 deletions(-)
> >
> > diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> > index 3a5df1440822..b1f4d19edd4f 100644
> > --- a/drivers/thermal/mtk_thermal.c
> > +++ b/drivers/thermal/mtk_thermal.c
> > @@ -259,6 +259,11 @@ enum mtk_thermal_version {
> >
> > struct mtk_thermal;
> >
> > +struct mtk_thermal_zone {
> > + struct mtk_thermal *mt;
> > + int id;
> > +};
> > +
> > struct thermal_bank_cfg {
> > unsigned int num_sensors;
> > const int *sensors;
> > @@ -307,6 +312,8 @@ struct mtk_thermal {
> >
> > const struct mtk_thermal_data *conf;
> > struct mtk_thermal_bank banks[MAX_NUM_ZONES];
> > +
> > + int (*raw_to_mcelsius)(struct mtk_thermal *mt, int sensno, s32 raw);
> > };
> >
> > /* MT8183 thermal sensor data */
> > @@ -709,6 +716,29 @@ static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
> > mutex_unlock(&mt->lock);
> > }
> >
> > +static int _get_sensor_temp(struct mtk_thermal *mt, int id)
> > +{
> > + u32 raw;
> > + int temp;
> > +
> > + const struct mtk_thermal_data *conf = mt->conf;
> > +
> > + raw = readl(mt->thermal_base + conf->msr[id]);
> > +
> > + temp = mt->raw_to_mcelsius(mt, id, raw);
> > +
> > + /*
> > + * The first read of a sensor often contains very high bogus
> > + * temperature value. Filter these out so that the system does
> > + * not immediately shut down.
> > + */
> > +
> > + if (temp > 200000)
> > + return -EAGAIN;
> > + else
> > + return temp;
> > +}
> > +
> > /**
> > * mtk_thermal_bank_temperature - get the temperature of a bank
> > * @bank: The bank
> > @@ -721,26 +751,9 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> > struct mtk_thermal *mt = bank->mt;
> > const struct mtk_thermal_data *conf = mt->conf;
> > int i, temp = INT_MIN, max = INT_MIN;
> > - u32 raw;
> >
> > for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
> > - raw = readl(mt->thermal_base + conf->msr[i]);
> > -
> > - if (mt->conf->version == MTK_THERMAL_V1) {
> > - temp = raw_to_mcelsius_v1(
> > - mt, conf->bank_data[bank->id].sensors[i], raw);
> > - } else {
> > - temp = raw_to_mcelsius_v2(
> > - mt, conf->bank_data[bank->id].sensors[i], raw);
> > - }
> > -
> > - /*
> > - * The first read of a sensor often contains very high bogus
> > - * temperature value. Filter these out so that the system does
> > - * not immediately shut down.
> > - */
> > - if (temp > 200000)
> > - temp = 0;
> > + temp = _get_sensor_temp(mt, i);
> >
> > if (temp > max)
> > max = temp;
> > @@ -749,9 +762,10 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> > return max;
> > }
> >
> > -static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
> > +static int mtk_read_temp(struct thermal_zone_device *tzdev, int *temperature)
> > {
> > - struct mtk_thermal *mt = tz->devdata;
> > + struct mtk_thermal_zone *tz = tzdev->devdata;
> > + struct mtk_thermal *mt = tz->mt;
> > int i;
> > int tempmax = INT_MIN;
> >
> > @@ -770,10 +784,28 @@ static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
> > return 0;
> > }
> >
> > +static int mtk_read_sensor_temp(struct thermal_zone_device *tzdev, int *temperature)
> > +{
> > + struct mtk_thermal_zone *tz = tzdev->devdata;
> > + struct mtk_thermal *mt = tz->mt;
> > + int id = tz->id - 1;
> > +
> > + if (id < 0)
> > + return -EACCES;
> > +
> > + *temperature = _get_sensor_temp(mt, id);
> > +
> > + return 0;
> > +}
> > +
> > static const struct thermal_zone_device_ops mtk_thermal_ops = {
> > .get_temp = mtk_read_temp,
> > };
> >
> > +static const struct thermal_zone_device_ops mtk_thermal_sensor_ops = {
> > + .get_temp = mtk_read_sensor_temp,
> > +};
> > +
> > static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
> > u32 apmixed_phys_base, u32 auxadc_phys_base,
> > int ctrl_id)
> > @@ -1072,6 +1104,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> > u64 auxadc_phys_base, apmixed_phys_base;
> > struct thermal_zone_device *tzdev;
> > void __iomem *apmixed_base, *auxadc_base;
> > + struct mtk_thermal_zone *tz;
> >
> > mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
> > if (!mt)
> > @@ -1150,6 +1183,9 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> >
> > mtk_thermal_turn_on_buffer(mt, apmixed_base);
> >
> > + mt->raw_to_mcelsius = (mt->conf->version == MTK_THERMAL_V1) ?
> > + raw_to_mcelsius_v1 : raw_to_mcelsius_v2;
> > +
> > if (mt->conf->version == MTK_THERMAL_V2) {
> > mtk_thermal_release_periodic_ts(mt, auxadc_base);
> > }
> > @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> >
> > platform_set_drvdata(pdev, mt);
> >
> > - tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
> > - &mtk_thermal_ops);
> > - if (IS_ERR(tzdev)) {
> > - ret = PTR_ERR(tzdev);
> > - goto err_disable_clk_peri_therm;
> > + for (i = 0; i < mt->conf->num_sensors + 1; i++) {
> > + tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
> > + if (!tz)
> > + return -ENOMEM;
> > +
> > + tz->mt = mt;
> > + tz->id = i;
> > +
> > + tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
> > + &mtk_thermal_ops :
> > + &mtk_thermal_sensor_ops);
>
> Here you use again the aggregation
I addressed this concern in V6, could you please take a look and let me
know what you think [0].
[0]: https://lore.kernel.org/all/[email protected]/
Regards,
Amjad
>
> > +
> > + if (IS_ERR(tzdev)) {
> > + ret = PTR_ERR(tzdev);
> > + if (ret == -ENODEV)
> > + continue;
> > + goto err_disable_clk_peri_therm;
> > + }
> > }
> >
> > ret = devm_thermal_add_hwmon_sysfs(tzdev);
> >
>
> --
> <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>
> Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
> <http://twitter.com/#!/linaroorg> Twitter |
> <http://www.linaro.org/linaro-blog/> Blog
Hi Amjad,
On 05/12/2022 11:41, Amjad Ouled-Ameur wrote:
[ ... ]
>>> @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>>>
>>> platform_set_drvdata(pdev, mt);
>>>
>>> - tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
>>> - &mtk_thermal_ops);
>>> - if (IS_ERR(tzdev)) {
>>> - ret = PTR_ERR(tzdev);
>>> - goto err_disable_clk_peri_therm;
>>> + for (i = 0; i < mt->conf->num_sensors + 1; i++) {
>>> + tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
>>> + if (!tz)
>>> + return -ENOMEM;
>>> +
>>> + tz->mt = mt;
>>> + tz->id = i;
>>> +
>>> + tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
>>> + &mtk_thermal_ops :
>>> + &mtk_thermal_sensor_ops);
>>
>> Here you use again the aggregation
> I addressed this concern in V6, could you please take a look and let me
> know what you think [0].
>
> [0]: https://lore.kernel.org/all/[email protected]/
May I misunderstanding but AFAICS, this patch is setting the
mtk_thermal_ops if the sensor id is zero. The get_temp is computing the
max temperature in this ops which is what we don't want to do.
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
Hi Daniel,
On Mon Dec 5, 2022 at 8:39 PM CET, Daniel Lezcano wrote:
>
> Hi Amjad,
>
>
> On 05/12/2022 11:41, Amjad Ouled-Ameur wrote:
>
> [ ... ]
>
> >>> @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> >>>
> >>> platform_set_drvdata(pdev, mt);
> >>>
> >>> - tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
> >>> - &mtk_thermal_ops);
> >>> - if (IS_ERR(tzdev)) {
> >>> - ret = PTR_ERR(tzdev);
> >>> - goto err_disable_clk_peri_therm;
> >>> + for (i = 0; i < mt->conf->num_sensors + 1; i++) {
> >>> + tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
> >>> + if (!tz)
> >>> + return -ENOMEM;
> >>> +
> >>> + tz->mt = mt;
> >>> + tz->id = i;
> >>> +
> >>> + tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
> >>> + &mtk_thermal_ops :
> >>> + &mtk_thermal_sensor_ops);
> >>
> >> Here you use again the aggregation
> > I addressed this concern in V6, could you please take a look and let me
> > know what you think [0].
> >
> > [0]: https://lore.kernel.org/all/[email protected]/
>
> May I misunderstanding but AFAICS, this patch is setting the
> mtk_thermal_ops if the sensor id is zero. The get_temp is computing the
> max temperature in this ops which is what we don't want to do.
Correct, but I think that is out of scope of this patchset, as the current
driver already uses mtk_thermal_ops for sensor 0. The focus of this patchset
is to add support for the other sensors.
Besides, what do you suggest as a clean implementation if the current one
no longer meets thermal core requirements ?
Regards,
Amjad
>
>
> --
> <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>
> Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
> <http://twitter.com/#!/linaroorg> Twitter |
> <http://www.linaro.org/linaro-blog/> Blog
Hi Daniel,
On 12/6/22 10:18, Amjad Ouled-Ameur wrote:
> Hi Daniel,
> On Mon Dec 5, 2022 at 8:39 PM CET, Daniel Lezcano wrote:
>> Hi Amjad,
>>
>>
>> On 05/12/2022 11:41, Amjad Ouled-Ameur wrote:
>>
>> [ ... ]
>>
>>>>> @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>>>>>
>>>>> platform_set_drvdata(pdev, mt);
>>>>>
>>>>> - tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
>>>>> - &mtk_thermal_ops);
>>>>> - if (IS_ERR(tzdev)) {
>>>>> - ret = PTR_ERR(tzdev);
>>>>> - goto err_disable_clk_peri_therm;
>>>>> + for (i = 0; i < mt->conf->num_sensors + 1; i++) {
>>>>> + tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
>>>>> + if (!tz)
>>>>> + return -ENOMEM;
>>>>> +
>>>>> + tz->mt = mt;
>>>>> + tz->id = i;
>>>>> +
>>>>> + tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
>>>>> + &mtk_thermal_ops :
>>>>> + &mtk_thermal_sensor_ops);
>>>> Here you use again the aggregation
>>> I addressed this concern in V6, could you please take a look and let me
>>> know what you think [0].
>>>
>>> [0]: https://lore.kernel.org/all/[email protected]/
>> May I misunderstanding but AFAICS, this patch is setting the
>> mtk_thermal_ops if the sensor id is zero. The get_temp is computing the
>> max temperature in this ops which is what we don't want to do.
> Correct, but I think that is out of scope of this patchset, as the current
> driver already uses mtk_thermal_ops for sensor 0. The focus of this patchset
> is to add support for the other sensors.
>
> Besides, what do you suggest as a clean implementation if the current one
> no longer meets thermal core requirements ?
Could you please address this ?
Kindly,
Amjad
> Regards,
> Amjad
>>
>> --
>> <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>>
>> Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
>> <http://twitter.com/#!/linaroorg> Twitter |
>> <http://www.linaro.org/linaro-blog/> Blog
On 06/12/2022 10:18, Amjad Ouled-Ameur wrote:
> Hi Daniel,
> On Mon Dec 5, 2022 at 8:39 PM CET, Daniel Lezcano wrote:
>>
>> Hi Amjad,
>>
>>
>> On 05/12/2022 11:41, Amjad Ouled-Ameur wrote:
>>
>> [ ... ]
>>
>>>>> @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>>>>>
>>>>> platform_set_drvdata(pdev, mt);
>>>>>
>>>>> - tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
>>>>> - &mtk_thermal_ops);
>>>>> - if (IS_ERR(tzdev)) {
>>>>> - ret = PTR_ERR(tzdev);
>>>>> - goto err_disable_clk_peri_therm;
>>>>> + for (i = 0; i < mt->conf->num_sensors + 1; i++) {
>>>>> + tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
>>>>> + if (!tz)
>>>>> + return -ENOMEM;
>>>>> +
>>>>> + tz->mt = mt;
>>>>> + tz->id = i;
>>>>> +
>>>>> + tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
>>>>> + &mtk_thermal_ops :
>>>>> + &mtk_thermal_sensor_ops);
>>>>
>>>> Here you use again the aggregation
>>> I addressed this concern in V6, could you please take a look and let me
>>> know what you think [0].
>>>
>>> [0]: https://lore.kernel.org/all/[email protected]/
>>
>> May I misunderstanding but AFAICS, this patch is setting the
>> mtk_thermal_ops if the sensor id is zero. The get_temp is computing the
>> max temperature in this ops which is what we don't want to do.
>
> Correct, but I think that is out of scope of this patchset, as the current
> driver already uses mtk_thermal_ops for sensor 0. The focus of this patchset
> is to add support for the other sensors.
>
> Besides, what do you suggest as a clean implementation if the current one
> no longer meets thermal core requirements ?
IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x 2Bigs, 1 x 4
Little, right ?
If it is the case, then a thermal zone per sensor with the trip points
and a cooling device for each of them.
The two thermal zones for the big will share the same cooling device.
The little thermal zone will have its own cooling device.
If there is the GPU, then its own cooling device also with devfreq.
>> <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>>
>> Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
>> <http://twitter.com/#!/linaroorg> Twitter |
>> <http://www.linaro.org/linaro-blog/> Blog
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
Hi Daniel,
On 12/29/22 16:49, Daniel Lezcano wrote:
> On 06/12/2022 10:18, Amjad Ouled-Ameur wrote:
>> Hi Daniel,
>> On Mon Dec 5, 2022 at 8:39 PM CET, Daniel Lezcano wrote:
>>>
>>> Hi Amjad,
>>>
>>>
>>> On 05/12/2022 11:41, Amjad Ouled-Ameur wrote:
>>>
>>> [ ... ]
>>>
>>>>>> @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>>>>>> platform_set_drvdata(pdev, mt);
>>>>>> - tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
>>>>>> - &mtk_thermal_ops);
>>>>>> - if (IS_ERR(tzdev)) {
>>>>>> - ret = PTR_ERR(tzdev);
>>>>>> - goto err_disable_clk_peri_therm;
>>>>>> + for (i = 0; i < mt->conf->num_sensors + 1; i++) {
>>>>>> + tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
>>>>>> + if (!tz)
>>>>>> + return -ENOMEM;
>>>>>> +
>>>>>> + tz->mt = mt;
>>>>>> + tz->id = i;
>>>>>> +
>>>>>> + tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
>>>>>> + &mtk_thermal_ops :
>>>>>> + &mtk_thermal_sensor_ops);
>>>>>
>>>>> Here you use again the aggregation
>>>> I addressed this concern in V6, could you please take a look and let me
>>>> know what you think [0].
>>>>
>>>> [0]: https://lore.kernel.org/all/[email protected]/
>>>
>>> May I misunderstanding but AFAICS, this patch is setting the
>>> mtk_thermal_ops if the sensor id is zero. The get_temp is computing the
>>> max temperature in this ops which is what we don't want to do.
>>
>> Correct, but I think that is out of scope of this patchset, as the current
>> driver already uses mtk_thermal_ops for sensor 0. The focus of this patchset
>> is to add support for the other sensors.
>>
>> Besides, what do you suggest as a clean implementation if the current one
>> no longer meets thermal core requirements ?
>
> IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x 2Bigs, 1 x 4 Little, right ?
MT8365 SoC has 4 x A53 CPUs. The SoC has 4 thermal zones per sensor. Thermal zone 0 corresponds
to all 4 x A53 CPUs, the other thermal zones (1, 2 and 3) has nothing to do with CPUs. The cooling device type
used for CPUs is passive. FYI, thermal zones 1, 2 and 3 are present in the SoC for debug-purpose only, they are not supposed
to be used for production.
Regards,
Amjad
>
> If it is the case, then a thermal zone per sensor with the trip points and a cooling device for each of them.
>
> The two thermal zones for the big will share the same cooling device. The little thermal zone will have its own cooling device.
>
> If there is the GPU, then its own cooling device also with devfreq.
>
>
>>> <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>>>
>>> Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
>>> <http://twitter.com/#!/linaroorg> Twitter |
>>> <http://www.linaro.org/linaro-blog/> Blog
>>
>
Hi Daniel,
On 1/19/23 18:03, Amjad Ouled-Ameur wrote:
> Hi Daniel,
>
> On 12/29/22 16:49, Daniel Lezcano wrote:
>> On 06/12/2022 10:18, Amjad Ouled-Ameur wrote:
>>> Hi Daniel,
>>> On Mon Dec 5, 2022 at 8:39 PM CET, Daniel Lezcano wrote:
>>>>
>>>> Hi Amjad,
>>>>
>>>>
>>>> On 05/12/2022 11:41, Amjad Ouled-Ameur wrote:
>>>>
>>>> [ ... ]
>>>>
>>>>>>> @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>>>>>>> platform_set_drvdata(pdev, mt);
>>>>>>> - tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
>>>>>>> - &mtk_thermal_ops);
>>>>>>> - if (IS_ERR(tzdev)) {
>>>>>>> - ret = PTR_ERR(tzdev);
>>>>>>> - goto err_disable_clk_peri_therm;
>>>>>>> + for (i = 0; i < mt->conf->num_sensors + 1; i++) {
>>>>>>> + tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
>>>>>>> + if (!tz)
>>>>>>> + return -ENOMEM;
>>>>>>> +
>>>>>>> + tz->mt = mt;
>>>>>>> + tz->id = i;
>>>>>>> +
>>>>>>> + tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
>>>>>>> + &mtk_thermal_ops :
>>>>>>> + &mtk_thermal_sensor_ops);
>>>>>>
>>>>>> Here you use again the aggregation
>>>>> I addressed this concern in V6, could you please take a look and let me
>>>>> know what you think [0].
>>>>>
>>>>> [0]: https://lore.kernel.org/all/[email protected]/
>>>>
>>>> May I misunderstanding but AFAICS, this patch is setting the
>>>> mtk_thermal_ops if the sensor id is zero. The get_temp is computing the
>>>> max temperature in this ops which is what we don't want to do.
>>>
>>> Correct, but I think that is out of scope of this patchset, as the current
>>> driver already uses mtk_thermal_ops for sensor 0. The focus of this patchset
>>> is to add support for the other sensors.
>>>
>>> Besides, what do you suggest as a clean implementation if the current one
>>> no longer meets thermal core requirements ?
>>
>> IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x 2Bigs, 1 x 4 Little, right ?
>
> MT8365 SoC has 4 x A53 CPUs. The SoC has 4 thermal zones per sensor. Thermal zone 0 corresponds
>
> to all 4 x A53 CPUs, the other thermal zones (1, 2 and 3) has nothing to do with CPUs. The cooling device type
>
> used for CPUs is passive. FYI, thermal zones 1, 2 and 3 are present in the SoC for debug-purpose only, they are not supposed
>
> to be used for production.
>
After reconsidering the fact that zones 1, 2 and 3 are only used for dev/debug, it might be best to avoid
aggregation as you suggested, and keep only support for zone 0 in this driver. Thus I suggest I send a V8
where I keep only below fixes for this patch if that's okay with you:
- Define "raw_to_mcelsius" function pointer for "struct thermal_bank_cfg".
- Fix "mtk_thermal" variable in mtk_read_temp().
- Set "mt->raw_to_mcelsius" in probe().
For zones 1, 2 and 3 we can later add a different driver specific for dev/debug to probe them to
avoid confusion.
Regards,
Amjad
>
> Regards,
>
> Amjad
>
>>
>> If it is the case, then a thermal zone per sensor with the trip points and a cooling device for each of them.
>>
>> The two thermal zones for the big will share the same cooling device. The little thermal zone will have its own cooling device.
>>
>> If there is the GPU, then its own cooling device also with devfreq.
>>
>>
>>>> <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
>>>>
>>>> Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
>>>> <http://twitter.com/#!/linaroorg> Twitter |
>>>> <http://www.linaro.org/linaro-blog/> Blog
>>>
>>
Hi Amjad,
On 24/01/2023 11:08, Amjad Ouled-Ameur wrote:
[ ... ]
>>>
>>> IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x 2Bigs, 1
>>> x 4 Little, right ?
>>
>> MT8365 SoC has 4 x A53 CPUs. The SoC has 4 thermal zones per sensor.
>> Thermal zone 0 corresponds
>>
>> to all 4 x A53 CPUs, the other thermal zones (1, 2 and 3) has nothing
>> to do with CPUs. The cooling device type
>>
>> used for CPUs is passive. FYI, thermal zones 1, 2 and 3 are present in
>> the SoC for debug-purpose only, they are not supposed
>>
>> to be used for production.
>>
> After reconsidering the fact that zones 1, 2 and 3 are only used for
> dev/debug, it might be best to avo >
> aggregation as you suggested, and keep only support for zone 0 in this
> driver. Thus I suggest I send a V8
>
> where I keep only below fixes for this patch if that's okay with you:
>
> - Define "raw_to_mcelsius" function pointer for "struct thermal_bank_cfg".
>
> - Fix "mtk_thermal" variable in mtk_read_temp().
>
> - Set "mt->raw_to_mcelsius" in probe().
>
>
> For zones 1, 2 and 3 we can later add a different driver specific for
> dev/debug to probe them to
>
> avoid confusion.
You can add them in the driver and in the device tree, but just add the
cooling device for the thermal zone 0.
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
On 1/24/23 17:54, Daniel Lezcano wrote:
>
> Hi Amjad,
>
> On 24/01/2023 11:08, Amjad Ouled-Ameur wrote:
>
> [ ... ]
>
>>>>
>>>> IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x 2Bigs, 1 x 4 Little, right ?
>>>
>>> MT8365 SoC has 4 x A53 CPUs. The SoC has 4 thermal zones per sensor. Thermal zone 0 corresponds
>>>
>>> to all 4 x A53 CPUs, the other thermal zones (1, 2 and 3) has nothing to do with CPUs. The cooling device type
>>>
>>> used for CPUs is passive. FYI, thermal zones 1, 2 and 3 are present in the SoC for debug-purpose only, they are not supposed
>>>
>>> to be used for production.
>>>
>> After reconsidering the fact that zones 1, 2 and 3 are only used for dev/debug, it might be best to avo >
>> aggregation as you suggested, and keep only support for zone 0 in this driver. Thus I suggest I send a V8
>>
>> where I keep only below fixes for this patch if that's okay with you:
>>
>> - Define "raw_to_mcelsius" function pointer for "struct thermal_bank_cfg".
>>
>> - Fix "mtk_thermal" variable in mtk_read_temp().
>>
>> - Set "mt->raw_to_mcelsius" in probe().
>>
>>
>> For zones 1, 2 and 3 we can later add a different driver specific for dev/debug to probe them to
>>
>> avoid confusion.
>
> You can add them in the driver and in the device tree, but just add the cooling device for the thermal zone 0.
Thermal zone 0 uses CPU{0..3} for passive cooling, in this case we should register cooling device with
cpufreq_cooling_register() for each CPU right ?
>
>
On 24/01/2023 18:46, Amjad Ouled-Ameur wrote:
>
> On 1/24/23 17:54, Daniel Lezcano wrote:
>>
>> Hi Amjad,
>>
>> On 24/01/2023 11:08, Amjad Ouled-Ameur wrote:
>>
>> [ ... ]
>>
>>>>>
>>>>> IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x 2Bigs,
>>>>> 1 x 4 Little, right ?
>>>>
>>>> MT8365 SoC has 4 x A53 CPUs. The SoC has 4 thermal zones per sensor.
>>>> Thermal zone 0 corresponds
>>>>
>>>> to all 4 x A53 CPUs, the other thermal zones (1, 2 and 3) has
>>>> nothing to do with CPUs. The cooling device type
>>>>
>>>> used for CPUs is passive. FYI, thermal zones 1, 2 and 3 are present
>>>> in the SoC for debug-purpose only, they are not supposed
>>>>
>>>> to be used for production.
>>>>
>>> After reconsidering the fact that zones 1, 2 and 3 are only used for
>>> dev/debug, it might be best to avo >
>>> aggregation as you suggested, and keep only support for zone 0 in
>>> this driver. Thus I suggest I send a V8
>>>
>>> where I keep only below fixes for this patch if that's okay with you:
>>>
>>> - Define "raw_to_mcelsius" function pointer for "struct
>>> thermal_bank_cfg".
>>>
>>> - Fix "mtk_thermal" variable in mtk_read_temp().
>>>
>>> - Set "mt->raw_to_mcelsius" in probe().
>>>
>>>
>>> For zones 1, 2 and 3 we can later add a different driver specific for
>>> dev/debug to probe them to
>>>
>>> avoid confusion.
>>
>> You can add them in the driver and in the device tree, but just add
>> the cooling device for the thermal zone 0.
>
> Thermal zone 0 uses CPU{0..3} for passive cooling, in this case we
> should register cooling device with
>
> cpufreq_cooling_register() for each CPU right ?
No, the OF code device tree does already that. You just have to register
the different thermal zones.
Do you have a pointer to a device tree for this board and the thermal
setup ?
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
On 1/24/23 18:55, Daniel Lezcano wrote:
> On 24/01/2023 18:46, Amjad Ouled-Ameur wrote:
>>
>> On 1/24/23 17:54, Daniel Lezcano wrote:
>>>
>>> Hi Amjad,
>>>
>>> On 24/01/2023 11:08, Amjad Ouled-Ameur wrote:
>>>
>>> [ ... ]
>>>
>>>>>>
>>>>>> IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x 2Bigs, 1 x 4 Little, right ?
>>>>>
>>>>> MT8365 SoC has 4 x A53 CPUs. The SoC has 4 thermal zones per sensor. Thermal zone 0 corresponds
>>>>>
>>>>> to all 4 x A53 CPUs, the other thermal zones (1, 2 and 3) has nothing to do with CPUs. The cooling device type
>>>>>
>>>>> used for CPUs is passive. FYI, thermal zones 1, 2 and 3 are present in the SoC for debug-purpose only, they are not supposed
>>>>>
>>>>> to be used for production.
>>>>>
>>>> After reconsidering the fact that zones 1, 2 and 3 are only used for dev/debug, it might be best to avo >
>>>> aggregation as you suggested, and keep only support for zone 0 in this driver. Thus I suggest I send a V8
>>>>
>>>> where I keep only below fixes for this patch if that's okay with you:
>>>>
>>>> - Define "raw_to_mcelsius" function pointer for "struct thermal_bank_cfg".
>>>>
>>>> - Fix "mtk_thermal" variable in mtk_read_temp().
>>>>
>>>> - Set "mt->raw_to_mcelsius" in probe().
>>>>
>>>>
>>>> For zones 1, 2 and 3 we can later add a different driver specific for dev/debug to probe them to
>>>>
>>>> avoid confusion.
>>>
>>> You can add them in the driver and in the device tree, but just add the cooling device for the thermal zone 0.
>>
>> Thermal zone 0 uses CPU{0..3} for passive cooling, in this case we should register cooling device with
>>
>> cpufreq_cooling_register() for each CPU right ?
>
> No, the OF code device tree does already that. You just have to register the different thermal zones.
>
> Do you have a pointer to a device tree for this board and the thermal setup ?
Sure, here is a dtsi for MT8365 SoC which contains thermal nodes [0].
[0]: https://lore.kernel.org/linux-arm-kernel/[email protected]/#Z31arch:arm64:boot:dts:mediatek:mt8365.dtsi
>
>
On 24/01/2023 23:27, Amjad Ouled-Ameur wrote:
>
> On 1/24/23 18:55, Daniel Lezcano wrote:
>> On 24/01/2023 18:46, Amjad Ouled-Ameur wrote:
>>>
>>> On 1/24/23 17:54, Daniel Lezcano wrote:
>>>>
>>>> Hi Amjad,
>>>>
>>>> On 24/01/2023 11:08, Amjad Ouled-Ameur wrote:
>>>>
>>>> [ ... ]
>>>>
>>>>>>>
>>>>>>> IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x
>>>>>>> 2Bigs, 1 x 4 Little, right ?
>>>>>>
>>>>>> MT8365 SoC has 4 x A53 CPUs. The SoC has 4 thermal zones per
>>>>>> sensor. Thermal zone 0 corresponds
>>>>>>
>>>>>> to all 4 x A53 CPUs, the other thermal zones (1, 2 and 3) has
>>>>>> nothing to do with CPUs. The cooling device type
>>>>>>
>>>>>> used for CPUs is passive. FYI, thermal zones 1, 2 and 3 are
>>>>>> present in the SoC for debug-purpose only, they are not supposed
>>>>>>
>>>>>> to be used for production.
>>>>>>
>>>>> After reconsidering the fact that zones 1, 2 and 3 are only used
>>>>> for dev/debug, it might be best to avo >
>>>>> aggregation as you suggested, and keep only support for zone 0 in
>>>>> this driver. Thus I suggest I send a V8
>>>>>
>>>>> where I keep only below fixes for this patch if that's okay with you:
>>>>>
>>>>> - Define "raw_to_mcelsius" function pointer for "struct
>>>>> thermal_bank_cfg".
>>>>>
>>>>> - Fix "mtk_thermal" variable in mtk_read_temp().
>>>>>
>>>>> - Set "mt->raw_to_mcelsius" in probe().
>>>>>
>>>>>
>>>>> For zones 1, 2 and 3 we can later add a different driver specific
>>>>> for dev/debug to probe them to
>>>>>
>>>>> avoid confusion.
>>>>
>>>> You can add them in the driver and in the device tree, but just add
>>>> the cooling device for the thermal zone 0.
>>>
>>> Thermal zone 0 uses CPU{0..3} for passive cooling, in this case we
>>> should register cooling device with
>>>
>>> cpufreq_cooling_register() for each CPU right ?
>>
>> No, the OF code device tree does already that. You just have to
>> register the different thermal zones.
>>
>> Do you have a pointer to a device tree for this board and the thermal
>> setup ?
>
> Sure, here is a dtsi for MT8365 SoC which contains thermal nodes [0].
From my POV, there are two different setup with the DT but only one
implementation with the driver.
The driver should register all the thermal zones for each CPUs. For
that, make things nice with the defines for the dt-bindings like [1].
Then the device tree:
setup1:
Describe all the thermal zones in the DT which will be similar to [2].
Each CPU has a thermal zone, trip points and the same cooling device.
The first thermal zone reaching the trip temperature threshold will
start the mitigation. The thermal framework takes care of multiple
thermal zones sharing the same cooling device.
The result will be the same as the max temperature aggregation you did
previously.
setup2:
Describe all the thermal zones in the DT [3], but add the cooling device
only on the sensor you are interested in mitigating.
And finally, if the sensors should be used to describe a kind of
temperature gradient, a linear equation could be used but that is not
implemented yet in the thermal framework.
Hope that helps
-- Daniel
[1]
https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#Z2e.:..:20230124131717.128660-3-bchihi::40baylibre.com:1include:dt-bindings:thermal:mediatek-lvts.h
[2]
https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#m303240c4da71f6f37831e5d1b6f3da771ae8dd90
[3]
https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#Z2e.:..:20230124131717.128660-6-bchihi::40baylibre.com:1arch:arm64:boot:dts:mediatek:mt8195.dtsi
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
On 1/25/23 11:02, Daniel Lezcano wrote:
> On 24/01/2023 23:27, Amjad Ouled-Ameur wrote:
>>
>> On 1/24/23 18:55, Daniel Lezcano wrote:
>>> On 24/01/2023 18:46, Amjad Ouled-Ameur wrote:
>>>>
>>>> On 1/24/23 17:54, Daniel Lezcano wrote:
>>>>>
>>>>> Hi Amjad,
>>>>>
>>>>> On 24/01/2023 11:08, Amjad Ouled-Ameur wrote:
>>>>>
>>>>> [ ... ]
>>>>>
>>>>>>>>
>>>>>>>> IIUC, there is a sensor per couple of cores. 1 x 2Bigs, 1 x 2Bigs, 1 x 4 Little, right ?
>>>>>>>
>>>>>>> MT8365 SoC has 4 x A53 CPUs. The SoC has 4 thermal zones per sensor. Thermal zone 0 corresponds
>>>>>>>
>>>>>>> to all 4 x A53 CPUs, the other thermal zones (1, 2 and 3) has nothing to do with CPUs. The cooling device type
>>>>>>>
>>>>>>> used for CPUs is passive. FYI, thermal zones 1, 2 and 3 are present in the SoC for debug-purpose only, they are not supposed
>>>>>>>
>>>>>>> to be used for production.
>>>>>>>
>>>>>> After reconsidering the fact that zones 1, 2 and 3 are only used for dev/debug, it might be best to avo >
>>>>>> aggregation as you suggested, and keep only support for zone 0 in this driver. Thus I suggest I send a V8
>>>>>>
>>>>>> where I keep only below fixes for this patch if that's okay with you:
>>>>>>
>>>>>> - Define "raw_to_mcelsius" function pointer for "struct thermal_bank_cfg".
>>>>>>
>>>>>> - Fix "mtk_thermal" variable in mtk_read_temp().
>>>>>>
>>>>>> - Set "mt->raw_to_mcelsius" in probe().
>>>>>>
>>>>>>
>>>>>> For zones 1, 2 and 3 we can later add a different driver specific for dev/debug to probe them to
>>>>>>
>>>>>> avoid confusion.
>>>>>
>>>>> You can add them in the driver and in the device tree, but just add the cooling device for the thermal zone 0.
>>>>
>>>> Thermal zone 0 uses CPU{0..3} for passive cooling, in this case we should register cooling device with
>>>>
>>>> cpufreq_cooling_register() for each CPU right ?
>>>
>>> No, the OF code device tree does already that. You just have to register the different thermal zones.
>>>
>>> Do you have a pointer to a device tree for this board and the thermal setup ?
>>
>> Sure, here is a dtsi for MT8365 SoC which contains thermal nodes [0].
>
> From my POV, there are two different setup with the DT but only one implementation with the driver.
>
> The driver should register all the thermal zones for each CPUs. For that, make things nice with the defines for the dt-bindings like [1].
>
> Then the device tree:
>
> setup1:
>
> Describe all the thermal zones in the DT which will be similar to [2]. Each CPU has a thermal zone, trip points and the same cooling device.
>
> The first thermal zone reaching the trip temperature threshold will start the mitigation. The thermal framework takes care of multiple thermal zones sharing the same cooling device.
>
> The result will be the same as the max temperature aggregation you did previously.
>
> setup2:
>
> Describe all the thermal zones in the DT [3], but add the cooling device only on the sensor you are interested in mitigating.
>
>
> And finally, if the sensors should be used to describe a kind of temperature gradient, a linear equation could be used but that is not implemented yet in the thermal framework.
>
> Hope that helps
>
Thank you Daniel for the thorough insights.
FYI, MT8195 SoC you referred to has a different thermal architecture and sensor mapping than on MT8365. The latter has only one
useful thermal zone corresponding to 4 CPUs at once. The other 3 thermal zones have no real purpose and will probably
not be defined in dtsi. Thus I sent a V8 of this series to keep only support for thermal zone 0 of interest.
Kindly,
Amjad
> -- Daniel
>
> [1] https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#Z2e.:..:20230124131717.128660-3-bchihi::40baylibre.com:1include:dt-bindings:thermal:mediatek-lvts.h
>
> [2] https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#m303240c4da71f6f37831e5d1b6f3da771ae8dd90
>
> [3] https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#Z2e.:..:20230124131717.128660-6-bchihi::40baylibre.com:1arch:arm64:boot:dts:mediatek:mt8195.dtsi
>
>