Tidy up the "amplc_pci230" driver a bit. There are more changes to come
after this. The only one of these that should alter the object code is
patch 06, which replaces a udelay() call with usleep_range().
01) staging: comedi: amplc_pci230: reformat a load of comments
02) staging: comedi: amplc_pci230: fix checkpatch line over 80
characters
03) staging: comedi: amplc_pci230: logical continuations should be on
the previous line
04) staging: comedi: amplc_pci230: blank lines aren't necessary before a
close brace '}'
05) staging: comedi: amplc_pci230: alignment should match open
parenthesis
06) staging: comedi: amplc_pci230: usleep_range is preferred over udelay
07) staging: comedi: amplc_pci230: remove unused settling time constants
08) staging: comedi: amplc_pci230: remove PCI230_ADC_CONV
09) staging: comedi: amplc_pci230: remove PCI230_TEST_BIT()
10) staging: comedi: amplc_pci230: add whitespace to register values
11) staging: comedi: amplc_pci230: don't begin line with binary operator
12) staging: comedi: amplc_pci230: omit '!= 0' from logical expressions
13) staging: comedi: amplc_pci230: remove unnecessary braces
14) staging: comedi: amplc_pci230: remove some indentation in
pci230_ai_check_chanlist()
15) staging: comedi: amplc_pci230: no need for '&function'
16) staging: comedi: amplc_pci230: add whitespace to pci230_boards[]
17) staging: comedi: amplc_pci230: no need to initialize named members
to zero
18) staging: comedi: amplc_pci230: tidy up stuct pci230_private
19) staging: comedi: amplc_pci230: remove some unnecessary parentheses
drivers/staging/comedi/drivers/amplc_pci230.c | 1417 +++++++++++++------------
1 file changed, 736 insertions(+), 681 deletions(-)
Fix checkpatch issues "CHECK: Logical continuations should be on the
previous line".
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 33 +++++++++++++--------------
1 file changed, 16 insertions(+), 17 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index c6c3c4a..0609e51 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -694,8 +694,8 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
ok = 1;
claimed = 0;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES)
- && (res_mask != 0); b <<= 1, i++) {
+ for (b = 1, i = 0; (i < NUM_RESOURCES) && (res_mask != 0);
+ b <<= 1, i++) {
if ((res_mask & b) != 0) {
res_mask &= ~b;
if (devpriv->res_owner[i] == OWNER_NONE) {
@@ -733,8 +733,8 @@ static void put_resources(struct comedi_device *dev, unsigned int res_mask,
unsigned long irqflags;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES)
- && (res_mask != 0); b <<= 1, i++) {
+ for (b = 1, i = 0; (i < NUM_RESOURCES) && (res_mask != 0);
+ b <<= 1, i++) {
if ((res_mask & b) != 0) {
res_mask &= ~b;
if (devpriv->res_owner[i] == owner)
@@ -1291,8 +1291,8 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
* (otherwise there will be loads of "DAC FIFO not half full"
* interrupts).
*/
- if ((num_scans == 0)
- && ((dacstat & PCI230P2_DAC_FIFO_HALF) == 0)) {
+ if ((num_scans == 0) &&
+ ((dacstat & PCI230P2_DAC_FIFO_HALF) == 0)) {
dev_err(dev->class_dev, "AO buffer underrun\n");
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
}
@@ -1594,8 +1594,8 @@ static int pci230_ai_check_scan_period(struct comedi_cmd *cmd)
chanlist_len = 1;
min_scan_period = chanlist_len * cmd->convert_arg;
- if ((min_scan_period < chanlist_len)
- || (min_scan_period < cmd->convert_arg)) {
+ if ((min_scan_period < chanlist_len) ||
+ (min_scan_period < cmd->convert_arg)) {
/* Arithmetic overflow. */
min_scan_period = UINT_MAX;
err++;
@@ -1755,8 +1755,8 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* If scan_begin_src is not TRIG_FOLLOW, then a monostable will be
* set up to generate a fixed number of timed conversion pulses.
*/
- if ((cmd->scan_begin_src != TRIG_FOLLOW)
- && (cmd->convert_src != TRIG_TIMER))
+ if ((cmd->scan_begin_src != TRIG_FOLLOW) &&
+ (cmd->convert_src != TRIG_TIMER))
err |= -EINVAL;
if (err)
@@ -1987,9 +1987,8 @@ static int pci230_ai_inttrig_convert(struct comedi_device *dev,
* bit has a different meaning when FIFO enabled (and when
* FIFO not enabled, it only works for software triggers).
*/
- if (((devpriv->adccon & PCI230_ADC_IM_MASK)
- == PCI230_ADC_IM_DIF)
- && (devpriv->hwver == 0)) {
+ if (((devpriv->adccon & PCI230_ADC_IM_MASK) ==
+ PCI230_ADC_IM_DIF) && (devpriv->hwver == 0)) {
/* PCI230/260 in differential mode */
delayus = 8;
} else {
@@ -2263,8 +2262,8 @@ static void pci230_handle_ai(struct comedi_device *dev,
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else if (devpriv->ai_scan_count == 0) {
todo = 0;
- } else if ((devpriv->ai_scan_count > PCI230_ADC_FIFOLEVEL_HALFFULL)
- || (scanlen > PCI230_ADC_FIFOLEVEL_HALFFULL)) {
+ } else if ((devpriv->ai_scan_count > PCI230_ADC_FIFOLEVEL_HALFFULL) ||
+ (scanlen > PCI230_ADC_FIFOLEVEL_HALFFULL)) {
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else {
todo = (devpriv->ai_scan_count * scanlen)
@@ -2761,8 +2760,8 @@ static int pci230_attach_common(struct comedi_device *dev,
*/
extfunc |= PCI230P_EXTFUNC_GAT_EXTTRIG;
}
- if ((thisboard->ao_chans > 0)
- && (devpriv->hwver >= 2)) {
+ if ((thisboard->ao_chans > 0) &&
+ (devpriv->hwver >= 2)) {
/* Enable DAC FIFO functionality. */
extfunc |= PCI230P2_EXTFUNC_DACFIFO;
}
--
2.0.0
Fix checkpatch issue: "CHECK: Alignment should match open parenthesis".
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 51f28b6..76c4625 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -2872,7 +2872,7 @@ static int pci230_attach(struct comedi_device *dev, struct comedi_devconfig *it)
}
static int pci230_auto_attach(struct comedi_device *dev,
- unsigned long context_unused)
+ unsigned long context_unused)
{
struct pci_dev *pci_dev = comedi_to_pci_dev(dev);
int rc;
--
2.0.0
The `PCI230_TEST_BIT()` macro is never used. Remove it.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index e6744a5..f94b542 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -423,9 +423,6 @@
/* For PCI230+ hardware version 2 when DAC FIFO enabled. */
#define PCI230P2_INT_DAC (1<<4)
-/* Assumes bits numbered with zero offset, ie. 0-15 */
-#define PCI230_TEST_BIT(val, n) ((val>>n)&1)
-
/*
* (Potentially) shared resources and their owners
*/
--
2.0.0
The macro `PCI230_ADC_CONV` is never used. Just remove it. (At one
time, the value was written to the `PCI230_ADCSWTRIG` register to
trigger a conversion, but any value would do, and the driver no longer
uses that register to trigger conversions anyway.)
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 6 ------
1 file changed, 6 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 7983a0d..e6744a5 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -362,12 +362,6 @@
#define PCI230_ADC_FIFOLEVEL_FULL 4096 /* FIFO size */
/*
- * Value to write to ADCSWTRIG to trigger ADC conversion in software trigger
- * mode. Can be anything.
- */
-#define PCI230_ADC_CONV 0xffff
-
-/*
* PCI230+ EXTFUNC values.
*/
/* Route EXTTRIG pin to external gate inputs. */
--
2.0.0
Remove some pairs of parentheses that don't really improve readability.
Also, reduce the amount of leading whitespace in a few places.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 78 +++++++++++++--------------
1 file changed, 37 insertions(+), 41 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index d3df96b..bb01351 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -628,7 +628,7 @@ static inline void pci230_ao_write_nofifo(struct comedi_device *dev,
/* Write mangled datum to appropriate DACOUT register. */
outw(pci230_ao_mangle_datum(dev, datum),
- dev->iobase + (((chan) == 0) ? PCI230_DACOUT1 : PCI230_DACOUT2));
+ dev->iobase + (chan == 0 ? PCI230_DACOUT1 : PCI230_DACOUT2));
}
static inline void pci230_ao_write_fifo(struct comedi_device *dev,
@@ -657,7 +657,7 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
ok = 1;
claimed = 0;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++)
+ for (b = 1, i = 0; i < NUM_RESOURCES && res_mask; b <<= 1, i++)
if (res_mask & b) {
res_mask &= ~b;
if (devpriv->res_owner[i] == OWNER_NONE) {
@@ -682,7 +682,7 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
static inline int get_one_resource(struct comedi_device *dev,
unsigned int resource, unsigned char owner)
{
- return get_resources(dev, (1U << resource), owner);
+ return get_resources(dev, 1U << resource, owner);
}
static void put_resources(struct comedi_device *dev, unsigned int res_mask,
@@ -694,7 +694,7 @@ static void put_resources(struct comedi_device *dev, unsigned int res_mask,
unsigned long irqflags;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++)
+ for (b = 1, i = 0; i < NUM_RESOURCES && res_mask; b <<= 1, i++)
if (res_mask & b) {
res_mask &= ~b;
if (devpriv->res_owner[i] == owner)
@@ -706,7 +706,7 @@ static void put_resources(struct comedi_device *dev, unsigned int res_mask,
static inline void put_one_resource(struct comedi_device *dev,
unsigned int resource, unsigned char owner)
{
- put_resources(dev, (1U << resource), owner);
+ put_resources(dev, 1U << resource, owner);
}
static inline void put_all_resources(struct comedi_device *dev,
@@ -748,7 +748,7 @@ static unsigned int pci230_choose_clk_count(uint64_t ns, unsigned int *count,
for (clk_src = CLK_10MHZ;; clk_src++) {
cnt = divide_ns(ns, pci230_timebase[clk_src], flags);
- if ((cnt <= 65536) || (clk_src == CLK_1KHZ))
+ if (cnt <= 65536 || clk_src == CLK_1KHZ)
break;
}
*count = cnt;
@@ -1005,7 +1005,7 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_src(&cmd->start_src, TRIG_INT);
tmp = TRIG_TIMER | TRIG_INT;
- if ((thisboard->min_hwver > 0) && (devpriv->hwver >= 2))
+ if (thisboard->min_hwver > 0 && devpriv->hwver >= 2)
/*
* For PCI230+ hardware version 2 onwards, allow external
* trigger from EXTTRIG/EXTCONVCLK input (PCI230+ pin 25).
@@ -1072,11 +1072,11 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
* The only flags allowed are CR_EDGE and CR_INVERT.
* The CR_EDGE flag is ignored.
*/
- if (cmd->scan_begin_arg &
- (CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT))) {
- cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
- CR_FLAGS_MASK &
- ~(CR_EDGE | CR_INVERT));
+ if (cmd->scan_begin_arg & CR_FLAGS_MASK &
+ ~(CR_EDGE | CR_INVERT)) {
+ cmd->scan_begin_arg =
+ COMBINE(cmd->scan_begin_arg, 0,
+ CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT));
err |= -EINVAL;
}
break;
@@ -1241,8 +1241,8 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
* (otherwise there will be loads of "DAC FIFO not half full"
* interrupts).
*/
- if ((num_scans == 0) &&
- ((dacstat & PCI230P2_DAC_FIFO_HALF) == 0)) {
+ if (num_scans == 0 &&
+ (dacstat & PCI230P2_DAC_FIFO_HALF) == 0) {
dev_err(dev->class_dev, "AO buffer underrun\n");
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
}
@@ -1537,8 +1537,8 @@ static int pci230_ai_check_scan_period(struct comedi_cmd *cmd)
chanlist_len = 1;
min_scan_period = chanlist_len * cmd->convert_arg;
- if ((min_scan_period < chanlist_len) ||
- (min_scan_period < cmd->convert_arg)) {
+ if (min_scan_period < chanlist_len ||
+ min_scan_period < cmd->convert_arg) {
/* Arithmetic overflow. */
min_scan_period = UINT_MAX;
err++;
@@ -1666,7 +1666,7 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_src(&cmd->start_src, TRIG_NOW | TRIG_INT);
tmp = TRIG_FOLLOW | TRIG_TIMER | TRIG_INT;
- if ((thisboard->have_dio) || (thisboard->min_hwver > 0))
+ if (thisboard->have_dio || thisboard->min_hwver > 0)
/*
* Unfortunately, we cannot trigger a scan off an external
* source on the PCI260 board, since it uses the PPIC0 (DIO)
@@ -1696,8 +1696,8 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* If scan_begin_src is not TRIG_FOLLOW, then a monostable will be
* set up to generate a fixed number of timed conversion pulses.
*/
- if ((cmd->scan_begin_src != TRIG_FOLLOW) &&
- (cmd->convert_src != TRIG_TIMER))
+ if (cmd->scan_begin_src != TRIG_FOLLOW &&
+ cmd->convert_src != TRIG_TIMER)
err |= -EINVAL;
if (err)
@@ -1724,7 +1724,7 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* PCI230 or PCI260. Max speed depends whether
* single-ended or pseudo-differential.
*/
- if (cmd->chanlist && (cmd->chanlist_len > 0))
+ if (cmd->chanlist && cmd->chanlist_len > 0)
/* Peek analogue reference of first channel. */
if (CR_AREF(cmd->chanlist[0]) == AREF_DIFF)
max_speed_ai = MAX_SPEED_AI_DIFF;
@@ -1762,13 +1762,12 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* The only flags allowed are CR_INVERT and CR_EDGE.
* CR_EDGE is required.
*/
- if ((cmd->convert_arg &
- (CR_FLAGS_MASK & ~CR_INVERT)) != CR_EDGE) {
+ if ((cmd->convert_arg & CR_FLAGS_MASK & ~CR_INVERT) !=
+ CR_EDGE) {
/* Set CR_EDGE, preserve CR_INVERT. */
- cmd->convert_arg = COMBINE(cmd->start_arg,
- (CR_EDGE | 0),
- CR_FLAGS_MASK &
- ~CR_INVERT);
+ cmd->convert_arg =
+ COMBINE(cmd->start_arg, CR_EDGE | 0,
+ CR_FLAGS_MASK & ~CR_INVERT);
err |= -EINVAL;
}
} else {
@@ -1871,11 +1870,10 @@ static void pci230_ai_update_fifo_trigger_level(struct comedi_device *dev,
scanlen >= PCI230_ADC_FIFOLEVEL_HALFFULL)
wake = PCI230_ADC_FIFOLEVEL_HALFFULL;
else
- wake = (devpriv->ai_scan_count * scanlen) -
- devpriv->ai_scan_pos;
+ wake = devpriv->ai_scan_count * scanlen - devpriv->ai_scan_pos;
if (wake >= PCI230_ADC_FIFOLEVEL_HALFFULL) {
triglev = PCI230_ADC_INT_FIFO_HALF;
- } else if ((wake > 1) && (devpriv->hwver > 0)) {
+ } else if (wake > 1 && devpriv->hwver > 0) {
/* PCI230+/260+ programmable FIFO interrupt level. */
if (devpriv->adcfifothresh != wake) {
devpriv->adcfifothresh = wake;
@@ -1921,8 +1919,8 @@ static int pci230_ai_inttrig_convert(struct comedi_device *dev,
* bit has a different meaning when FIFO enabled (and when
* FIFO not enabled, it only works for software triggers).
*/
- if (((devpriv->adccon & PCI230_ADC_IM_MASK) ==
- PCI230_ADC_IM_DIF) && (devpriv->hwver == 0)) {
+ if ((devpriv->adccon & PCI230_ADC_IM_MASK) ==
+ PCI230_ADC_IM_DIF && devpriv->hwver == 0) {
/* PCI230/260 in differential mode */
delayus = 8;
} else {
@@ -2190,12 +2188,11 @@ static void pci230_handle_ai(struct comedi_device *dev,
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else if (devpriv->ai_scan_count == 0) {
todo = 0;
- } else if ((devpriv->ai_scan_count > PCI230_ADC_FIFOLEVEL_HALFFULL) ||
- (scanlen > PCI230_ADC_FIFOLEVEL_HALFFULL)) {
+ } else if (devpriv->ai_scan_count > PCI230_ADC_FIFOLEVEL_HALFFULL ||
+ scanlen > PCI230_ADC_FIFOLEVEL_HALFFULL) {
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else {
- todo = (devpriv->ai_scan_count * scanlen) -
- devpriv->ai_scan_pos;
+ todo = devpriv->ai_scan_count * scanlen - devpriv->ai_scan_pos;
if (todo > PCI230_ADC_FIFOLEVEL_HALFFULL)
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
}
@@ -2285,13 +2282,13 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
* Need Z2-CT2 to supply a conversion trigger source at a high
* logic level, even if not doing timed conversions.
*/
- res_mask |= (1U << RES_Z2CT2);
+ res_mask |= 1U << RES_Z2CT2;
if (cmd->scan_begin_src != TRIG_FOLLOW) {
/* Using Z2-CT0 monostable to gate Z2-CT2 conversion timer */
- res_mask |= (1U << RES_Z2CT0);
+ res_mask |= 1U << RES_Z2CT0;
if (cmd->scan_begin_src == TRIG_TIMER)
/* Using Z2-CT1 for scan frequency */
- res_mask |= (1U << RES_Z2CT1);
+ res_mask |= 1U << RES_Z2CT1;
}
/* Claim resources. */
if (!get_resources(dev, res_mask, OWNER_AICMD))
@@ -2363,7 +2360,7 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
*/
adcen |= 1 << gainshift;
} else {
- gainshift = (chan & ~1);
+ gainshift = chan & ~1;
adcen |= 1 << chan;
}
devpriv->adcg = (devpriv->adcg & ~(3 << gainshift)) |
@@ -2682,8 +2679,7 @@ static int pci230_attach_common(struct comedi_device *dev,
* on PCI260[+].)
*/
extfunc |= PCI230P_EXTFUNC_GAT_EXTTRIG;
- if ((thisboard->ao_chans > 0) &&
- (devpriv->hwver >= 2))
+ if (thisboard->ao_chans > 0 && devpriv->hwver >= 2)
/* Enable DAC FIFO functionality. */
extfunc |= PCI230P2_EXTFUNC_DACFIFO;
}
--
2.0.0
Align the member comments a bit better in the declaration of `struct
pci230_private`. Also remove the heading comment as it is just a
boilerplate comedi comment.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 45 ++++++++++-----------------
1 file changed, 17 insertions(+), 28 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 135ca63..d3df96b 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -508,40 +508,29 @@ static const struct pci230_board pci230_boards[] = {
},
};
-/*
- * This structure is for data unique to this hardware driver. If
- * several hardware drivers keep similar information in this structure,
- * feel free to suggest moving the variable to the struct comedi_device struct.
- */
struct pci230_private {
spinlock_t isr_spinlock; /* Interrupt spin lock */
spinlock_t res_spinlock; /* Shared resources spin lock */
spinlock_t ai_stop_spinlock; /* Spin lock for stopping AI command */
spinlock_t ao_stop_spinlock; /* Spin lock for stopping AO command */
- unsigned long state; /* State flags */
- unsigned long iobase1; /* PCI230's I/O space 1 */
+ unsigned long state; /* State flags */
+ unsigned long iobase1; /* PCI230's I/O space 1 */
unsigned int ao_readback[2]; /* Used for AO readback */
- /* Number of analogue input scans remaining. */
- unsigned int ai_scan_count;
- /* Current position within analogue input scan */
- unsigned int ai_scan_pos;
- /* Number of analogue output scans remaining. */
- unsigned int ao_scan_count;
- int intr_cpuid; /* ID of CPU running interrupt routine. */
- unsigned short hwver; /* Hardware version (for '+' models). */
- unsigned short adccon; /* ADCCON register value. */
- unsigned short daccon; /* DACCON register value. */
- /* ADC FIFO programmable interrupt level threshold (PCI230+/260+). */
- unsigned short adcfifothresh;
- unsigned short adcg; /* ADCG register value. */
- unsigned char int_en; /* Interrupt enables bits. */
- /* Set if bipolar input range so we know to mangle it. */
- unsigned char ai_bipolar;
- /* Set if bipolar output range so we know to mangle it. */
- unsigned char ao_bipolar;
- unsigned char ier; /* Copy of interrupt enables/status register. */
- unsigned char intr_running; /* Flag set in interrupt routine. */
- unsigned char res_owner[NUM_RESOURCES]; /* Shared resource owners. */
+ unsigned int ai_scan_count; /* Number of AI scans remaining */
+ unsigned int ai_scan_pos; /* Current position within AI scan */
+ unsigned int ao_scan_count; /* Number of AO scans remaining. */
+ int intr_cpuid; /* ID of CPU running ISR */
+ unsigned short hwver; /* Hardware version (for '+' models) */
+ unsigned short adccon; /* ADCCON register value */
+ unsigned short daccon; /* DACCON register value */
+ unsigned short adcfifothresh; /* ADC FIFO threshold (PCI230+/260+) */
+ unsigned short adcg; /* ADCG register value */
+ unsigned char int_en; /* Interrupt enable bits */
+ unsigned char ai_bipolar; /* Flag AI range is bipolar */
+ unsigned char ao_bipolar; /* Flag AO range is bipolar */
+ unsigned char ier; /* Copy of interrupt enable register */
+ unsigned char intr_running; /* Flag set in interrupt routine */
+ unsigned char res_owner[NUM_RESOURCES]; /* Shared resource owners */
};
/* PCI230 clock source periods in ns */
--
2.0.0
The members of the elements of `pci230_boards[]` that are not explicitly
named in their initializers will be initialized to 0 automatically, so
there is no need to initialize them to 0 explicitly.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 6 ------
1 file changed, 6 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 47e10ba..135ca63 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -484,9 +484,6 @@ static const struct pci230_board pci230_boards[] = {
.id = PCI_DEVICE_ID_PCI260,
.ai_chans = 16,
.ai_bits = 16,
- .ao_chans = 0,
- .ao_bits = 0,
- .have_dio = 0,
.min_hwver = 1,
},
{
@@ -503,9 +500,6 @@ static const struct pci230_board pci230_boards[] = {
.id = PCI_DEVICE_ID_PCI260,
.ai_chans = 16,
.ai_bits = 12,
- .ao_chans = 0,
- .ao_bits = 0,
- .have_dio = 0,
},
{
/* Wildcard matches any above */
--
2.0.0
Several macros are defined for bit-field values within hardware
registers. They are defined as left-shifted values. Add some
whitespace around the left-shift operator.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 128 +++++++++++++-------------
1 file changed, 64 insertions(+), 64 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index f94b542..4d3d3cb 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -249,47 +249,47 @@
/*
* DACCON read-write values.
*/
-#define PCI230_DAC_OR_UNI (0<<0) /* Output range unipolar */
-#define PCI230_DAC_OR_BIP (1<<0) /* Output range bipolar */
-#define PCI230_DAC_OR_MASK (1<<0)
+#define PCI230_DAC_OR_UNI (0 << 0) /* Output range unipolar */
+#define PCI230_DAC_OR_BIP (1 << 0) /* Output range bipolar */
+#define PCI230_DAC_OR_MASK (1 << 0)
/*
* The following applies only if DAC FIFO support is enabled in the EXTFUNC
* register (and only for PCI230+ hardware version 2 onwards).
*/
-#define PCI230P2_DAC_FIFO_EN (1<<8) /* FIFO enable */
+#define PCI230P2_DAC_FIFO_EN (1 << 8) /* FIFO enable */
/*
* The following apply only if the DAC FIFO is enabled (and only for PCI230+
* hardware version 2 onwards).
*/
-#define PCI230P2_DAC_TRIG_NONE (0<<2) /* No trigger */
-#define PCI230P2_DAC_TRIG_SW (1<<2) /* Software trigger trigger */
-#define PCI230P2_DAC_TRIG_EXTP (2<<2) /* EXTTRIG +ve edge trigger */
-#define PCI230P2_DAC_TRIG_EXTN (3<<2) /* EXTTRIG -ve edge trigger */
-#define PCI230P2_DAC_TRIG_Z2CT0 (4<<2) /* CT0-OUT +ve edge trigger */
-#define PCI230P2_DAC_TRIG_Z2CT1 (5<<2) /* CT1-OUT +ve edge trigger */
-#define PCI230P2_DAC_TRIG_Z2CT2 (6<<2) /* CT2-OUT +ve edge trigger */
-#define PCI230P2_DAC_TRIG_MASK (7<<2)
-#define PCI230P2_DAC_FIFO_WRAP (1<<7) /* FIFO wraparound mode */
-#define PCI230P2_DAC_INT_FIFO_EMPTY (0<<9) /* FIFO interrupt empty */
-#define PCI230P2_DAC_INT_FIFO_NEMPTY (1<<9)
-#define PCI230P2_DAC_INT_FIFO_NHALF (2<<9) /* FIFO intr not half full */
-#define PCI230P2_DAC_INT_FIFO_HALF (3<<9)
-#define PCI230P2_DAC_INT_FIFO_NFULL (4<<9) /* FIFO interrupt not full */
-#define PCI230P2_DAC_INT_FIFO_FULL (5<<9)
-#define PCI230P2_DAC_INT_FIFO_MASK (7<<9)
+#define PCI230P2_DAC_TRIG_NONE (0 << 2) /* No trigger */
+#define PCI230P2_DAC_TRIG_SW (1 << 2) /* Software trigger trigger */
+#define PCI230P2_DAC_TRIG_EXTP (2 << 2) /* EXTTRIG +ve edge trigger */
+#define PCI230P2_DAC_TRIG_EXTN (3 << 2) /* EXTTRIG -ve edge trigger */
+#define PCI230P2_DAC_TRIG_Z2CT0 (4 << 2) /* CT0-OUT +ve edge trigger */
+#define PCI230P2_DAC_TRIG_Z2CT1 (5 << 2) /* CT1-OUT +ve edge trigger */
+#define PCI230P2_DAC_TRIG_Z2CT2 (6 << 2) /* CT2-OUT +ve edge trigger */
+#define PCI230P2_DAC_TRIG_MASK (7 << 2)
+#define PCI230P2_DAC_FIFO_WRAP (1 << 7) /* FIFO wraparound mode */
+#define PCI230P2_DAC_INT_FIFO_EMPTY (0 << 9) /* FIFO interrupt empty */
+#define PCI230P2_DAC_INT_FIFO_NEMPTY (1 << 9)
+#define PCI230P2_DAC_INT_FIFO_NHALF (2 << 9) /* FIFO intr not half full */
+#define PCI230P2_DAC_INT_FIFO_HALF (3 << 9)
+#define PCI230P2_DAC_INT_FIFO_NFULL (4 << 9) /* FIFO interrupt not full */
+#define PCI230P2_DAC_INT_FIFO_FULL (5 << 9)
+#define PCI230P2_DAC_INT_FIFO_MASK (7 << 9)
/*
* DACCON read-only values.
*/
-#define PCI230_DAC_BUSY (1<<1) /* DAC busy. */
+#define PCI230_DAC_BUSY (1 << 1) /* DAC busy. */
/*
* The following apply only if the DAC FIFO is enabled (and only for PCI230+
* hardware version 2 onwards).
*/
-#define PCI230P2_DAC_FIFO_UNDERRUN_LATCHED (1<<5) /* Underrun error */
-#define PCI230P2_DAC_FIFO_EMPTY (1<<13) /* FIFO empty */
-#define PCI230P2_DAC_FIFO_FULL (1<<14) /* FIFO full */
-#define PCI230P2_DAC_FIFO_HALF (1<<15) /* FIFO half full */
+#define PCI230P2_DAC_FIFO_UNDERRUN_LATCHED (1 << 5) /* Underrun error */
+#define PCI230P2_DAC_FIFO_EMPTY (1 << 13) /* FIFO empty */
+#define PCI230P2_DAC_FIFO_FULL (1 << 14) /* FIFO full */
+#define PCI230P2_DAC_FIFO_HALF (1 << 15) /* FIFO half full */
/*
* DACCON write-only, transient values.
@@ -298,8 +298,8 @@
* The following apply only if the DAC FIFO is enabled (and only for PCI230+
* hardware version 2 onwards).
*/
-#define PCI230P2_DAC_FIFO_UNDERRUN_CLEAR (1<<5) /* Clear underrun */
-#define PCI230P2_DAC_FIFO_RESET (1<<12) /* FIFO reset */
+#define PCI230P2_DAC_FIFO_UNDERRUN_CLEAR (1 << 5) /* Clear underrun */
+#define PCI230P2_DAC_FIFO_RESET (1 << 12) /* FIFO reset */
/*
* PCI230+ hardware version 2 DAC FIFO levels.
@@ -316,44 +316,44 @@
/*
* ADCCON read/write values.
*/
-#define PCI230_ADC_TRIG_NONE (0<<0) /* No trigger */
-#define PCI230_ADC_TRIG_SW (1<<0) /* Software trigger trigger */
-#define PCI230_ADC_TRIG_EXTP (2<<0) /* EXTTRIG +ve edge trigger */
-#define PCI230_ADC_TRIG_EXTN (3<<0) /* EXTTRIG -ve edge trigger */
-#define PCI230_ADC_TRIG_Z2CT0 (4<<0) /* CT0-OUT +ve edge trigger */
-#define PCI230_ADC_TRIG_Z2CT1 (5<<0) /* CT1-OUT +ve edge trigger */
-#define PCI230_ADC_TRIG_Z2CT2 (6<<0) /* CT2-OUT +ve edge trigger */
-#define PCI230_ADC_TRIG_MASK (7<<0)
-#define PCI230_ADC_IR_UNI (0<<3) /* Input range unipolar */
-#define PCI230_ADC_IR_BIP (1<<3) /* Input range bipolar */
-#define PCI230_ADC_IR_MASK (1<<3)
-#define PCI230_ADC_IM_SE (0<<4) /* Input mode single ended */
-#define PCI230_ADC_IM_DIF (1<<4) /* Input mode differential */
-#define PCI230_ADC_IM_MASK (1<<4)
-#define PCI230_ADC_FIFO_EN (1<<8) /* FIFO enable */
-#define PCI230_ADC_INT_FIFO_EMPTY (0<<9)
-#define PCI230_ADC_INT_FIFO_NEMPTY (1<<9) /* FIFO interrupt not empty */
-#define PCI230_ADC_INT_FIFO_NHALF (2<<9)
-#define PCI230_ADC_INT_FIFO_HALF (3<<9) /* FIFO interrupt half full */
-#define PCI230_ADC_INT_FIFO_NFULL (4<<9)
-#define PCI230_ADC_INT_FIFO_FULL (5<<9) /* FIFO interrupt full */
-#define PCI230P_ADC_INT_FIFO_THRESH (7<<9) /* FIFO interrupt threshold */
-#define PCI230_ADC_INT_FIFO_MASK (7<<9)
+#define PCI230_ADC_TRIG_NONE (0 << 0) /* No trigger */
+#define PCI230_ADC_TRIG_SW (1 << 0) /* Software trigger trigger */
+#define PCI230_ADC_TRIG_EXTP (2 << 0) /* EXTTRIG +ve edge trigger */
+#define PCI230_ADC_TRIG_EXTN (3 << 0) /* EXTTRIG -ve edge trigger */
+#define PCI230_ADC_TRIG_Z2CT0 (4 << 0) /* CT0-OUT +ve edge trigger */
+#define PCI230_ADC_TRIG_Z2CT1 (5 << 0) /* CT1-OUT +ve edge trigger */
+#define PCI230_ADC_TRIG_Z2CT2 (6 << 0) /* CT2-OUT +ve edge trigger */
+#define PCI230_ADC_TRIG_MASK (7 << 0)
+#define PCI230_ADC_IR_UNI (0 << 3) /* Input range unipolar */
+#define PCI230_ADC_IR_BIP (1 << 3) /* Input range bipolar */
+#define PCI230_ADC_IR_MASK (1 << 3)
+#define PCI230_ADC_IM_SE (0 << 4) /* Input mode single ended */
+#define PCI230_ADC_IM_DIF (1 << 4) /* Input mode differential */
+#define PCI230_ADC_IM_MASK (1 << 4)
+#define PCI230_ADC_FIFO_EN (1 << 8) /* FIFO enable */
+#define PCI230_ADC_INT_FIFO_EMPTY (0 << 9)
+#define PCI230_ADC_INT_FIFO_NEMPTY (1 << 9) /* FIFO interrupt not empty */
+#define PCI230_ADC_INT_FIFO_NHALF (2 << 9)
+#define PCI230_ADC_INT_FIFO_HALF (3 << 9) /* FIFO interrupt half full */
+#define PCI230_ADC_INT_FIFO_NFULL (4 << 9)
+#define PCI230_ADC_INT_FIFO_FULL (5 << 9) /* FIFO interrupt full */
+#define PCI230P_ADC_INT_FIFO_THRESH (7 << 9) /* FIFO interrupt threshold */
+#define PCI230_ADC_INT_FIFO_MASK (7 << 9)
/*
* ADCCON write-only, transient values.
*/
-#define PCI230_ADC_FIFO_RESET (1<<12) /* FIFO reset */
-#define PCI230_ADC_GLOB_RESET (1<<13) /* Global reset */
+#define PCI230_ADC_FIFO_RESET (1 << 12) /* FIFO reset */
+#define PCI230_ADC_GLOB_RESET (1 << 13) /* Global reset */
/*
* ADCCON read-only values.
*/
-#define PCI230_ADC_BUSY (1<<15) /* ADC busy */
-#define PCI230_ADC_FIFO_EMPTY (1<<12) /* FIFO empty */
-#define PCI230_ADC_FIFO_FULL (1<<13) /* FIFO full */
-#define PCI230_ADC_FIFO_HALF (1<<14) /* FIFO half full */
-#define PCI230_ADC_FIFO_FULL_LATCHED (1<<5) /* Indicates overrun occurred */
+#define PCI230_ADC_BUSY (1 << 15) /* ADC busy */
+#define PCI230_ADC_FIFO_EMPTY (1 << 12) /* FIFO empty */
+#define PCI230_ADC_FIFO_FULL (1 << 13) /* FIFO full */
+#define PCI230_ADC_FIFO_HALF (1 << 14) /* FIFO half full */
+#define PCI230_ADC_FIFO_FULL_LATCHED (1 << 5) /* FIFO overrun occurred */
/*
* PCI230 ADC FIFO levels.
@@ -365,10 +365,10 @@
* PCI230+ EXTFUNC values.
*/
/* Route EXTTRIG pin to external gate inputs. */
-#define PCI230P_EXTFUNC_GAT_EXTTRIG (1<<0)
+#define PCI230P_EXTFUNC_GAT_EXTTRIG (1 << 0)
/* PCI230+ hardware version 2 values. */
/* Allow DAC FIFO to be enabled. */
-#define PCI230P2_EXTFUNC_DACFIFO (1<<1)
+#define PCI230P2_EXTFUNC_DACFIFO (1 << 1)
/*
* Counter/timer clock input configuration sources.
@@ -416,12 +416,12 @@
* Interrupt enables/status register values.
*/
#define PCI230_INT_DISABLE 0
-#define PCI230_INT_PPI_C0 (1<<0)
-#define PCI230_INT_PPI_C3 (1<<1)
-#define PCI230_INT_ADC (1<<2)
-#define PCI230_INT_ZCLK_CT1 (1<<5)
+#define PCI230_INT_PPI_C0 (1 << 0)
+#define PCI230_INT_PPI_C3 (1 << 1)
+#define PCI230_INT_ADC (1 << 2)
+#define PCI230_INT_ZCLK_CT1 (1 << 5)
/* For PCI230+ hardware version 2 when DAC FIFO enabled. */
-#define PCI230P2_INT_DAC (1<<4)
+#define PCI230P2_INT_DAC (1 << 4)
/*
* (Potentially) shared resources and their owners
--
2.0.0
Remove the "address-of" operator when the operand is a function.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index c2da10c..395eba2 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -2746,13 +2746,13 @@ static int pci230_attach_common(struct comedi_device *dev,
s->n_chan = thisboard->ai_chans;
s->maxdata = (1 << thisboard->ai_bits) - 1;
s->range_table = &pci230_ai_range;
- s->insn_read = &pci230_ai_rinsn;
+ s->insn_read = pci230_ai_rinsn;
s->len_chanlist = 256; /* but there are restrictions. */
if (dev->irq) {
dev->read_subdev = s;
s->subdev_flags |= SDF_CMD_READ;
- s->do_cmd = &pci230_ai_cmd;
- s->do_cmdtest = &pci230_ai_cmdtest;
+ s->do_cmd = pci230_ai_cmd;
+ s->do_cmdtest = pci230_ai_cmdtest;
s->cancel = pci230_ai_cancel;
}
@@ -2764,14 +2764,14 @@ static int pci230_attach_common(struct comedi_device *dev,
s->n_chan = thisboard->ao_chans;
s->maxdata = (1 << thisboard->ao_bits) - 1;
s->range_table = &pci230_ao_range;
- s->insn_write = &pci230_ao_winsn;
- s->insn_read = &pci230_ao_rinsn;
+ s->insn_write = pci230_ao_winsn;
+ s->insn_read = pci230_ao_rinsn;
s->len_chanlist = thisboard->ao_chans;
if (dev->irq) {
dev->write_subdev = s;
s->subdev_flags |= SDF_CMD_WRITE;
- s->do_cmd = &pci230_ao_cmd;
- s->do_cmdtest = &pci230_ao_cmdtest;
+ s->do_cmd = pci230_ao_cmd;
+ s->do_cmdtest = pci230_ao_cmdtest;
s->cancel = pci230_ao_cancel;
}
} else {
--
2.0.0
Add a bit of whitespace to the initializer of `pci230_boards[]` for
aesthetic reasons.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 76 ++++++++++++++-------------
1 file changed, 39 insertions(+), 37 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 395eba2..47e10ba 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -467,49 +467,51 @@ struct pci230_board {
int have_dio;
unsigned int min_hwver; /* Minimum hardware version supported. */
};
+
static const struct pci230_board pci230_boards[] = {
{
- .name = "pci230+",
- .id = PCI_DEVICE_ID_PCI230,
- .ai_chans = 16,
- .ai_bits = 16,
- .ao_chans = 2,
- .ao_bits = 12,
- .have_dio = 1,
- .min_hwver = 1,
- },
+ .name = "pci230+",
+ .id = PCI_DEVICE_ID_PCI230,
+ .ai_chans = 16,
+ .ai_bits = 16,
+ .ao_chans = 2,
+ .ao_bits = 12,
+ .have_dio = 1,
+ .min_hwver = 1,
+ },
{
- .name = "pci260+",
- .id = PCI_DEVICE_ID_PCI260,
- .ai_chans = 16,
- .ai_bits = 16,
- .ao_chans = 0,
- .ao_bits = 0,
- .have_dio = 0,
- .min_hwver = 1,
- },
+ .name = "pci260+",
+ .id = PCI_DEVICE_ID_PCI260,
+ .ai_chans = 16,
+ .ai_bits = 16,
+ .ao_chans = 0,
+ .ao_bits = 0,
+ .have_dio = 0,
+ .min_hwver = 1,
+ },
{
- .name = "pci230",
- .id = PCI_DEVICE_ID_PCI230,
- .ai_chans = 16,
- .ai_bits = 12,
- .ao_chans = 2,
- .ao_bits = 12,
- .have_dio = 1,
- },
+ .name = "pci230",
+ .id = PCI_DEVICE_ID_PCI230,
+ .ai_chans = 16,
+ .ai_bits = 12,
+ .ao_chans = 2,
+ .ao_bits = 12,
+ .have_dio = 1,
+ },
{
- .name = "pci260",
- .id = PCI_DEVICE_ID_PCI260,
- .ai_chans = 16,
- .ai_bits = 12,
- .ao_chans = 0,
- .ao_bits = 0,
- .have_dio = 0,
- },
+ .name = "pci260",
+ .id = PCI_DEVICE_ID_PCI260,
+ .ai_chans = 16,
+ .ai_bits = 12,
+ .ao_chans = 0,
+ .ao_bits = 0,
+ .have_dio = 0,
+ },
{
- .name = "amplc_pci230", /* Wildcard matches any above */
- .id = PCI_DEVICE_ID_INVALID,
- },
+ /* Wildcard matches any above */
+ .name = "amplc_pci230",
+ .id = PCI_DEVICE_ID_INVALID,
+ },
};
/*
--
2.0.0
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 151 ++++++++++----------------
1 file changed, 58 insertions(+), 93 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 4222e28..df58679 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -672,7 +672,7 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
ok = 1;
claimed = 0;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++) {
+ for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++)
if (res_mask & b) {
res_mask &= ~b;
if (devpriv->res_owner[i] == OWNER_NONE) {
@@ -690,7 +690,6 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
break;
}
}
- }
spin_unlock_irqrestore(&devpriv->res_spinlock, irqflags);
return ok;
}
@@ -710,13 +709,12 @@ static void put_resources(struct comedi_device *dev, unsigned int res_mask,
unsigned long irqflags;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++) {
+ for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++)
if (res_mask & b) {
res_mask &= ~b;
if (devpriv->res_owner[i] == owner)
devpriv->res_owner[i] = OWNER_NONE;
}
- }
spin_unlock_irqrestore(&devpriv->res_spinlock, irqflags);
}
@@ -839,7 +837,7 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
chan = CR_CHAN(insn->chanspec);
range = CR_RANGE(insn->chanspec);
aref = CR_AREF(insn->chanspec);
- if (aref == AREF_DIFF) {
+ if (aref == AREF_DIFF)
/* Differential. */
if (chan >= s->n_chan / 2) {
dev_dbg(dev->class_dev,
@@ -847,7 +845,6 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
__func__, (s->n_chan / 2) - 1);
return -EINVAL;
}
- }
/*
* Use Z2-CT2 as a conversion trigger instead of the built-in
@@ -862,19 +859,18 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
if (aref == AREF_DIFF) {
/* Differential. */
gainshift = chan * 2;
- if (devpriv->hwver == 0) {
+ if (devpriv->hwver == 0)
/*
* Original PCI230/260 expects both inputs of the
* differential channel to be enabled.
*/
adcen = 3 << gainshift;
- } else {
+ else
/*
* PCI230+/260+ expects only one input of the
* differential channel to be enabled.
*/
adcen = 1 << gainshift;
- }
adccon |= PCI230_ADC_IM_DIF;
} else {
/* Single ended. */
@@ -953,10 +949,9 @@ static int pci230_ao_winsn(struct comedi_device *dev,
* Writing a list of values to an AO channel is probably not
* very useful, but that's how the interface is defined.
*/
- for (i = 0; i < insn->n; i++) {
+ for (i = 0; i < insn->n; i++)
/* Write value to DAC and store it. */
pci230_ao_write_nofifo(dev, data[i], chan);
- }
/* return the number of samples read/written */
return i;
@@ -1025,7 +1020,7 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_src(&cmd->start_src, TRIG_INT);
tmp = TRIG_TIMER | TRIG_INT;
- if ((thisboard->min_hwver > 0) && (devpriv->hwver >= 2)) {
+ if ((thisboard->min_hwver > 0) && (devpriv->hwver >= 2))
/*
* For PCI230+ hardware version 2 onwards, allow external
* trigger from EXTTRIG/EXTCONVCLK input (PCI230+ pin 25).
@@ -1041,7 +1036,6 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
* guarantee!
*/
tmp |= TRIG_EXT;
- }
err |= cfc_check_trigger_src(&cmd->scan_begin_src, tmp);
err |= cfc_check_trigger_src(&cmd->convert_src, TRIG_NOW);
@@ -1151,18 +1145,16 @@ static void pci230_ao_stop(struct comedi_device *dev,
if (!started)
return;
cmd = &s->async->cmd;
- if (cmd->scan_begin_src == TRIG_TIMER) {
+ if (cmd->scan_begin_src == TRIG_TIMER)
/* Stop scan rate generator. */
pci230_cancel_ct(dev, 1);
- }
/* Determine interrupt source. */
- if (devpriv->hwver < 2) {
+ if (devpriv->hwver < 2)
/* Not using DAC FIFO. Using CT1 interrupt. */
intsrc = PCI230_INT_ZCLK_CT1;
- } else {
+ else
/* Using DAC FIFO interrupt. */
intsrc = PCI230P2_INT_DAC;
- }
/*
* Disable interrupt and wait for interrupt routine to finish running
* unless we are called from the interrupt routine.
@@ -1249,10 +1241,9 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
/* Fixed number of scans. */
if (num_scans > devpriv->ao_scan_count)
num_scans = devpriv->ao_scan_count;
- if (devpriv->ao_scan_count == 0) {
+ if (devpriv->ao_scan_count == 0)
/* End of acquisition. */
events |= COMEDI_CB_EOA;
- }
}
if (events == 0) {
/* Check for FIFO underrun. */
@@ -1287,7 +1278,7 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
if (num_scans > room)
num_scans = room;
/* Process scans. */
- for (n = 0; n < num_scans; n++) {
+ for (n = 0; n < num_scans; n++)
for (i = 0; i < cmd->chanlist_len; i++) {
unsigned short datum;
@@ -1295,7 +1286,6 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
pci230_ao_write_fifo(dev, datum,
CR_CHAN(cmd->chanlist[i]));
}
- }
events |= COMEDI_CB_EOS | COMEDI_CB_BLOCK;
if (cmd->stop_src == TRIG_COUNT) {
devpriv->ao_scan_count -= num_scans;
@@ -1390,10 +1380,9 @@ static void pci230_ao_start(struct comedi_device *dev,
/* Preload FIFO data. */
run = pci230_handle_ao_fifo(dev, s);
comedi_event(dev, s);
- if (!run) {
+ if (!run)
/* Stopped. */
return;
- }
/* Set scan trigger source. */
switch (cmd->scan_begin_src) {
case TRIG_TIMER:
@@ -1401,13 +1390,12 @@ static void pci230_ao_start(struct comedi_device *dev,
break;
case TRIG_EXT:
/* Trigger on EXTTRIG/EXTCONVCLK pin. */
- if ((cmd->scan_begin_arg & CR_INVERT) == 0) {
+ if ((cmd->scan_begin_arg & CR_INVERT) == 0)
/* +ve edge */
scantrig = PCI230P2_DAC_TRIG_EXTP;
- } else {
+ else
/* -ve edge */
scantrig = PCI230P2_DAC_TRIG_EXTN;
- }
break;
case TRIG_INT:
scantrig = PCI230P2_DAC_TRIG_SW;
@@ -1480,11 +1468,10 @@ static int pci230_ao_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
/* Get the command. */
struct comedi_cmd *cmd = &s->async->cmd;
- if (cmd->scan_begin_src == TRIG_TIMER) {
+ if (cmd->scan_begin_src == TRIG_TIMER)
/* Claim Z2-CT1. */
if (!get_one_resource(dev, RES_Z2CT1, OWNER_AOCMD))
return -EBUSY;
- }
/* Get number of scans required. */
if (cmd->stop_src == TRIG_COUNT)
@@ -1670,14 +1657,13 @@ static int pci230_ai_check_chanlist(struct comedi_device *dev,
* be invisible to software). The first one doesn't seem to have
* the bug, but the second one does, and we can't tell them apart!
*/
- if (devpriv->hwver > 0 && devpriv->hwver < 4) {
+ if (devpriv->hwver > 0 && devpriv->hwver < 4)
if (subseq_len > 1 && CR_CHAN(cmd->chanlist[0])) {
dev_info(dev->class_dev,
"amplc_pci230: ai_cmdtest: Buggy PCI230+/260+ h/w version %u requires first channel of multi-channel sequence to be 0 (corrected in h/w version 4)\n",
devpriv->hwver);
return -EINVAL;
}
- }
return 0;
}
@@ -1695,7 +1681,7 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_src(&cmd->start_src, TRIG_NOW | TRIG_INT);
tmp = TRIG_FOLLOW | TRIG_TIMER | TRIG_INT;
- if ((thisboard->have_dio) || (thisboard->min_hwver > 0)) {
+ if ((thisboard->have_dio) || (thisboard->min_hwver > 0))
/*
* Unfortunately, we cannot trigger a scan off an external
* source on the PCI260 board, since it uses the PPIC0 (DIO)
@@ -1703,7 +1689,6 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* we can use the EXTTRIG/EXTCONVCLK input on pin 17 instead.
*/
tmp |= TRIG_EXT;
- }
err |= cfc_check_trigger_src(&cmd->scan_begin_src, tmp);
err |= cfc_check_trigger_src(&cmd->convert_src,
TRIG_TIMER | TRIG_INT | TRIG_EXT);
@@ -1749,26 +1734,24 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
if (cmd->convert_src == TRIG_TIMER) {
unsigned int max_speed_ai;
- if (devpriv->hwver == 0) {
+ if (devpriv->hwver == 0)
/*
* PCI230 or PCI260. Max speed depends whether
* single-ended or pseudo-differential.
*/
- if (cmd->chanlist && (cmd->chanlist_len > 0)) {
+ if (cmd->chanlist && (cmd->chanlist_len > 0))
/* Peek analogue reference of first channel. */
if (CR_AREF(cmd->chanlist[0]) == AREF_DIFF)
max_speed_ai = MAX_SPEED_AI_DIFF;
else
max_speed_ai = MAX_SPEED_AI_SE;
- } else {
+ else
/* No channel list. Assume single-ended. */
max_speed_ai = MAX_SPEED_AI_SE;
- }
- } else {
+ else
/* PCI230+ or PCI260+. */
max_speed_ai = MAX_SPEED_AI_PLUS;
- }
err |= cfc_check_trigger_arg_min(&cmd->convert_arg,
max_speed_ai);
@@ -1895,32 +1878,27 @@ static void pci230_ai_update_fifo_trigger_level(struct comedi_device *dev,
unsigned short triglev;
unsigned short adccon;
- if (cmd->flags & TRIG_WAKE_EOS) {
+ if (cmd->flags & TRIG_WAKE_EOS)
/* Wake at end of scan. */
wake = scanlen - devpriv->ai_scan_pos;
- } else {
- if (cmd->stop_src != TRIG_COUNT ||
- devpriv->ai_scan_count >= PCI230_ADC_FIFOLEVEL_HALFFULL ||
- scanlen >= PCI230_ADC_FIFOLEVEL_HALFFULL) {
- wake = PCI230_ADC_FIFOLEVEL_HALFFULL;
- } else {
- wake = (devpriv->ai_scan_count * scanlen) -
- devpriv->ai_scan_pos;
- }
- }
+ else if (cmd->stop_src != TRIG_COUNT ||
+ devpriv->ai_scan_count >= PCI230_ADC_FIFOLEVEL_HALFFULL ||
+ scanlen >= PCI230_ADC_FIFOLEVEL_HALFFULL)
+ wake = PCI230_ADC_FIFOLEVEL_HALFFULL;
+ else
+ wake = (devpriv->ai_scan_count * scanlen) -
+ devpriv->ai_scan_pos;
if (wake >= PCI230_ADC_FIFOLEVEL_HALFFULL) {
triglev = PCI230_ADC_INT_FIFO_HALF;
- } else {
- if ((wake > 1) && (devpriv->hwver > 0)) {
- /* PCI230+/260+ programmable FIFO interrupt level. */
- if (devpriv->adcfifothresh != wake) {
- devpriv->adcfifothresh = wake;
- outw(wake, dev->iobase + PCI230P_ADCFFTH);
- }
- triglev = PCI230P_ADC_INT_FIFO_THRESH;
- } else {
- triglev = PCI230_ADC_INT_FIFO_NEMPTY;
+ } else if ((wake > 1) && (devpriv->hwver > 0)) {
+ /* PCI230+/260+ programmable FIFO interrupt level. */
+ if (devpriv->adcfifothresh != wake) {
+ devpriv->adcfifothresh = wake;
+ outw(wake, dev->iobase + PCI230P_ADCFFTH);
}
+ triglev = PCI230P_ADC_INT_FIFO_THRESH;
+ } else {
+ triglev = PCI230_ADC_INT_FIFO_NEMPTY;
}
adccon = (devpriv->adccon & ~PCI230_ADC_INT_FIFO_MASK) | triglev;
if (adccon != devpriv->adccon) {
@@ -2013,14 +1991,12 @@ static void pci230_ai_stop(struct comedi_device *dev,
if (!started)
return;
cmd = &s->async->cmd;
- if (cmd->convert_src == TRIG_TIMER) {
+ if (cmd->convert_src == TRIG_TIMER)
/* Stop conversion rate generator. */
pci230_cancel_ct(dev, 2);
- }
- if (cmd->scan_begin_src != TRIG_FOLLOW) {
+ if (cmd->scan_begin_src != TRIG_FOLLOW)
/* Stop scan period monostable. */
pci230_cancel_ct(dev, 0);
- }
spin_lock_irqsave(&devpriv->isr_spinlock, irqflags);
/*
* Disable ADC interrupt and wait for interrupt routine to finish
@@ -2085,24 +2061,21 @@ static void pci230_ai_start(struct comedi_device *dev,
conv = PCI230_ADC_TRIG_Z2CT2;
break;
case TRIG_EXT:
- if (cmd->convert_arg & CR_EDGE) {
- if ((cmd->convert_arg & CR_INVERT) == 0) {
+ if (cmd->convert_arg & CR_EDGE)
+ if ((cmd->convert_arg & CR_INVERT) == 0)
/* Trigger on +ve edge. */
conv = PCI230_ADC_TRIG_EXTP;
- } else {
+ else
/* Trigger on -ve edge. */
conv = PCI230_ADC_TRIG_EXTN;
- }
- } else {
+ else
/* Backwards compatibility. */
- if (cmd->convert_arg) {
+ if (cmd->convert_arg)
/* Trigger on +ve edge. */
conv = PCI230_ADC_TRIG_EXTP;
- } else {
+ else
/* Trigger on -ve edge. */
conv = PCI230_ADC_TRIG_EXTN;
- }
- }
break;
case TRIG_INT:
/*
@@ -2127,19 +2100,18 @@ static void pci230_ai_start(struct comedi_device *dev,
/* Update timer gates. */
unsigned char zgat;
- if (cmd->scan_begin_src != TRIG_FOLLOW) {
+ if (cmd->scan_begin_src != TRIG_FOLLOW)
/*
* Conversion timer CT2 needs to be gated by
* inverted output of monostable CT2.
*/
zgat = GAT_CONFIG(2, GAT_NOUTNM2);
- } else {
+ else
/*
* Conversion timer CT2 needs to be gated on
* continuously.
*/
zgat = GAT_CONFIG(2, GAT_VCC);
- }
outb(zgat, devpriv->iobase1 + PCI230_ZGAT_SCE);
if (cmd->scan_begin_src != TRIG_FOLLOW) {
/* Set monostable CT0 trigger source. */
@@ -2269,10 +2241,9 @@ static void pci230_handle_ai(struct comedi_device *dev,
/* Read PCI230+/260+ ADC FIFO level. */
fifoamount =
inw(dev->iobase + PCI230P_ADCFFLEV);
- if (fifoamount == 0) {
+ if (fifoamount == 0)
/* Shouldn't happen. */
break;
- }
} else {
fifoamount = 1;
}
@@ -2293,22 +2264,20 @@ static void pci230_handle_ai(struct comedi_device *dev,
async->events |= COMEDI_CB_EOS;
}
}
- if (cmd->stop_src == TRIG_COUNT && devpriv->ai_scan_count == 0) {
+ if (cmd->stop_src == TRIG_COUNT && devpriv->ai_scan_count == 0)
/* End of acquisition. */
events |= COMEDI_CB_EOA;
- } else {
+ else
/* More samples required, tell Comedi to block. */
events |= COMEDI_CB_BLOCK;
- }
async->events |= events;
if (async->events & (COMEDI_CB_EOA | COMEDI_CB_ERROR |
- COMEDI_CB_OVERFLOW)) {
+ COMEDI_CB_OVERFLOW))
/* disable hardware conversions */
pci230_ai_stop(dev, s);
- } else {
+ else
/* update FIFO interrupt trigger level */
pci230_ai_update_fifo_trigger_level(dev, s);
- }
}
static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
@@ -2335,10 +2304,9 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
if (cmd->scan_begin_src != TRIG_FOLLOW) {
/* Using Z2-CT0 monostable to gate Z2-CT2 conversion timer */
res_mask |= (1U << RES_Z2CT0);
- if (cmd->scan_begin_src == TRIG_TIMER) {
+ if (cmd->scan_begin_src == TRIG_TIMER)
/* Using Z2-CT1 for scan frequency */
res_mask |= (1U << RES_Z2CT1);
- }
}
/* Claim resources. */
if (!get_resources(dev, res_mask, OWNER_AICMD))
@@ -2397,19 +2365,18 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
range = CR_RANGE(cmd->chanlist[i]);
if (diff) {
gainshift = 2 * chan;
- if (devpriv->hwver == 0) {
+ if (devpriv->hwver == 0)
/*
* Original PCI230/260 expects both inputs of
* the differential channel to be enabled.
*/
adcen |= 3 << gainshift;
- } else {
+ else
/*
* PCI230+/260+ expects only one input of the
* differential channel to be enabled.
*/
adcen |= 1 << gainshift;
- }
} else {
gainshift = (chan & ~1);
adcen |= 1 << chan;
@@ -2721,7 +2688,7 @@ static int pci230_attach_common(struct comedi_device *dev,
return -EIO;
}
if (devpriv->hwver > 0) {
- if (!thisboard->have_dio) {
+ if (!thisboard->have_dio)
/*
* No DIO ports. Route counters' external gates
* to the EXTTRIG signal (PCI260+ pin 17).
@@ -2730,12 +2697,10 @@ static int pci230_attach_common(struct comedi_device *dev,
* on PCI260[+].)
*/
extfunc |= PCI230P_EXTFUNC_GAT_EXTTRIG;
- }
if ((thisboard->ao_chans > 0) &&
- (devpriv->hwver >= 2)) {
+ (devpriv->hwver >= 2))
/* Enable DAC FIFO functionality. */
extfunc |= PCI230P2_EXTFUNC_DACFIFO;
- }
}
outw(extfunc, dev->iobase + PCI230P_EXTFUNC);
if (extfunc & PCI230P2_EXTFUNC_DACFIFO) {
--
2.0.0
If an expression involving a binary operator needs to be split across
two lines, put the split after the operator.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 86 +++++++++++++--------------
1 file changed, 43 insertions(+), 43 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 4d3d3cb..311c497 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -682,8 +682,8 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
} else if (devpriv->res_owner[i] != owner) {
for (b = 1, i = 0; claimed != 0; b <<= 1, i++) {
if ((claimed & b) != 0) {
- devpriv->res_owner[i]
- = OWNER_NONE;
+ devpriv->res_owner[i] =
+ OWNER_NONE;
claimed &= ~b;
}
}
@@ -884,8 +884,8 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
gainshift = chan & ~1;
adccon |= PCI230_ADC_IM_SE;
}
- devpriv->adcg = (devpriv->adcg & ~(3 << gainshift))
- | (pci230_ai_gain[range] << gainshift);
+ devpriv->adcg = (devpriv->adcg & ~(3 << gainshift)) |
+ (pci230_ai_gain[range] << gainshift);
if (devpriv->ai_bipolar)
adccon |= PCI230_ADC_IR_BIP;
else
@@ -1095,8 +1095,8 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
* The only flags allowed are CR_EDGE and CR_INVERT.
* The CR_EDGE flag is ignored.
*/
- if ((cmd->scan_begin_arg
- & (CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT))) != 0) {
+ if ((cmd->scan_begin_arg &
+ (CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT))) != 0) {
cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
CR_FLAGS_MASK &
~(CR_EDGE | CR_INVERT));
@@ -1186,8 +1186,8 @@ static void pci230_ao_stop(struct comedi_device *dev,
* disable FIFO.
*/
devpriv->daccon &= PCI230_DAC_OR_MASK;
- outw(devpriv->daccon | PCI230P2_DAC_FIFO_RESET
- | PCI230P2_DAC_FIFO_UNDERRUN_CLEAR,
+ outw(devpriv->daccon | PCI230P2_DAC_FIFO_RESET |
+ PCI230P2_DAC_FIFO_UNDERRUN_CLEAR,
dev->iobase + PCI230_DACCON);
}
/* Release resources. */
@@ -1307,10 +1307,10 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
* to FIFO. Set FIFO interrupt trigger level
* to 'empty'.
*/
- devpriv->daccon = (devpriv->daccon
- &
- ~PCI230P2_DAC_INT_FIFO_MASK)
- | PCI230P2_DAC_INT_FIFO_EMPTY;
+ devpriv->daccon =
+ (devpriv->daccon &
+ ~PCI230P2_DAC_INT_FIFO_MASK) |
+ PCI230P2_DAC_INT_FIFO_EMPTY;
outw(devpriv->daccon,
dev->iobase + PCI230_DACCON);
}
@@ -1322,8 +1322,8 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
}
}
- if ((events & (COMEDI_CB_EOA | COMEDI_CB_ERROR | COMEDI_CB_OVERFLOW))
- != 0) {
+ if ((events &
+ (COMEDI_CB_EOA | COMEDI_CB_ERROR | COMEDI_CB_OVERFLOW)) != 0) {
/* Stopping AO due to completion or error. */
pci230_ao_stop(dev, s);
running = 0;
@@ -1420,8 +1420,8 @@ static void pci230_ao_start(struct comedi_device *dev,
scantrig = PCI230P2_DAC_TRIG_NONE;
break;
}
- devpriv->daccon = (devpriv->daccon
- & ~PCI230P2_DAC_TRIG_MASK) |
+ devpriv->daccon =
+ (devpriv->daccon & ~PCI230P2_DAC_TRIG_MASK) |
scantrig;
outw(devpriv->daccon, dev->iobase + PCI230_DACCON);
}
@@ -1521,16 +1521,16 @@ static int pci230_ao_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
*
* N.B. DAC FIFO interrupts are currently disabled.
*/
- daccon |= PCI230P2_DAC_FIFO_EN | PCI230P2_DAC_FIFO_RESET
- | PCI230P2_DAC_FIFO_UNDERRUN_CLEAR
- | PCI230P2_DAC_TRIG_NONE | PCI230P2_DAC_INT_FIFO_NHALF;
+ daccon |= PCI230P2_DAC_FIFO_EN | PCI230P2_DAC_FIFO_RESET |
+ PCI230P2_DAC_FIFO_UNDERRUN_CLEAR |
+ PCI230P2_DAC_TRIG_NONE | PCI230P2_DAC_INT_FIFO_NHALF;
}
/* Set DACCON. */
outw(daccon, dev->iobase + PCI230_DACCON);
/* Preserve most of DACCON apart from write-only, transient bits. */
- devpriv->daccon = daccon
- & ~(PCI230P2_DAC_FIFO_RESET | PCI230P2_DAC_FIFO_UNDERRUN_CLEAR);
+ devpriv->daccon = daccon & ~(PCI230P2_DAC_FIFO_RESET |
+ PCI230P2_DAC_FIFO_UNDERRUN_CLEAR);
if (cmd->scan_begin_src == TRIG_TIMER) {
/*
@@ -1797,8 +1797,8 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* The only flags allowed are CR_INVERT and CR_EDGE.
* CR_EDGE is required.
*/
- if ((cmd->convert_arg & (CR_FLAGS_MASK & ~CR_INVERT))
- != CR_EDGE) {
+ if ((cmd->convert_arg &
+ (CR_FLAGS_MASK & ~CR_INVERT)) != CR_EDGE) {
/* Set CR_EDGE, preserve CR_INVERT. */
cmd->convert_arg = COMBINE(cmd->start_arg,
(CR_EDGE | 0),
@@ -1907,8 +1907,8 @@ static void pci230_ai_update_fifo_trigger_level(struct comedi_device *dev,
scanlen >= PCI230_ADC_FIFOLEVEL_HALFFULL) {
wake = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else {
- wake = (devpriv->ai_scan_count * scanlen)
- - devpriv->ai_scan_pos;
+ wake = (devpriv->ai_scan_count * scanlen) -
+ devpriv->ai_scan_pos;
}
}
if (wake >= PCI230_ADC_FIFOLEVEL_HALFFULL) {
@@ -2043,8 +2043,8 @@ static void pci230_ai_stop(struct comedi_device *dev,
* Reset FIFO, disable FIFO and set start conversion source to none.
* Keep se/diff and bip/uni settings.
*/
- devpriv->adccon = (devpriv->adccon & (PCI230_ADC_IR_MASK
- | PCI230_ADC_IM_MASK)) |
+ devpriv->adccon =
+ (devpriv->adccon & (PCI230_ADC_IR_MASK | PCI230_ADC_IM_MASK)) |
PCI230_ADC_TRIG_NONE;
outw(devpriv->adccon | PCI230_ADC_FIFO_RESET,
dev->iobase + PCI230_ADCCON);
@@ -2115,8 +2115,8 @@ static void pci230_ai_start(struct comedi_device *dev,
conv = PCI230_ADC_TRIG_Z2CT2;
break;
}
- devpriv->adccon = (devpriv->adccon & ~PCI230_ADC_TRIG_MASK)
- | conv;
+ devpriv->adccon =
+ (devpriv->adccon & ~PCI230_ADC_TRIG_MASK) | conv;
outw(devpriv->adccon, dev->iobase + PCI230_ADCCON);
if (cmd->convert_src == TRIG_INT)
async->inttrig = pci230_ai_inttrig_convert;
@@ -2187,8 +2187,8 @@ static void pci230_ai_start(struct comedi_device *dev,
* gated on to start counting.
*/
zgat = GAT_CONFIG(1, GAT_VCC);
- outb(zgat, devpriv->iobase1
- + PCI230_ZGAT_SCE);
+ outb(zgat, devpriv->iobase1 +
+ PCI230_ZGAT_SCE);
break;
case TRIG_INT:
async->inttrig =
@@ -2240,8 +2240,8 @@ static void pci230_handle_ai(struct comedi_device *dev,
(scanlen > PCI230_ADC_FIFOLEVEL_HALFFULL)) {
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else {
- todo = (devpriv->ai_scan_count * scanlen)
- - devpriv->ai_scan_pos;
+ todo = (devpriv->ai_scan_count * scanlen) -
+ devpriv->ai_scan_pos;
if (todo > PCI230_ADC_FIFOLEVEL_HALFFULL)
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
}
@@ -2270,8 +2270,8 @@ static void pci230_handle_ai(struct comedi_device *dev,
/* FIFO not empty. */
if (devpriv->hwver > 0) {
/* Read PCI230+/260+ ADC FIFO level. */
- fifoamount = inw(dev->iobase
- + PCI230P_ADCFFLEV);
+ fifoamount =
+ inw(dev->iobase + PCI230P_ADCFFLEV);
if (fifoamount == 0) {
/* Shouldn't happen. */
break;
@@ -2417,8 +2417,8 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
gainshift = (chan & ~1);
adcen |= 1 << chan;
}
- devpriv->adcg = (devpriv->adcg & ~(3 << gainshift))
- | (pci230_ai_gain[range] << gainshift);
+ devpriv->adcg = (devpriv->adcg & ~(3 << gainshift)) |
+ (pci230_ai_gain[range] << gainshift);
}
/* Set channel scan list. */
@@ -2490,8 +2490,8 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
zgat = GAT_CONFIG(0, GAT_VCC);
outb(zgat, devpriv->iobase1 + PCI230_ZGAT_SCE);
pci230_ct_setup_ns_mode(dev, 0, I8254_MODE1,
- ((uint64_t) cmd->convert_arg
- * cmd->scan_end_arg),
+ ((uint64_t)cmd->convert_arg *
+ cmd->scan_end_arg),
TRIG_ROUND_UP);
if (cmd->scan_begin_src == TRIG_TIMER) {
/*
@@ -2746,8 +2746,8 @@ static int pci230_attach_common(struct comedi_device *dev,
* Temporarily enable DAC FIFO, reset it and disable
* FIFO wraparound.
*/
- outw(devpriv->daccon | PCI230P2_DAC_FIFO_EN
- | PCI230P2_DAC_FIFO_RESET,
+ outw(devpriv->daccon | PCI230P2_DAC_FIFO_EN |
+ PCI230P2_DAC_FIFO_RESET,
dev->iobase + PCI230_DACCON);
/* Clear DAC FIFO channel enable register. */
outw(0, dev->iobase + PCI230P2_DACEN);
@@ -2759,8 +2759,8 @@ static int pci230_attach_common(struct comedi_device *dev,
outb(0, devpriv->iobase1 + PCI230_INT_SCE);
/* Set ADC to a reasonable state. */
devpriv->adcg = 0;
- devpriv->adccon = PCI230_ADC_TRIG_NONE | PCI230_ADC_IM_SE
- | PCI230_ADC_IR_BIP;
+ devpriv->adccon = PCI230_ADC_TRIG_NONE | PCI230_ADC_IM_SE |
+ PCI230_ADC_IR_BIP;
outw(1 << 0, dev->iobase + PCI230_ADCEN);
outw(devpriv->adcg, dev->iobase + PCI230_ADCG);
outw(devpriv->adccon | PCI230_ADC_FIFO_RESET,
--
2.0.0
A few lines in `pci230_ai_check_chanlist()` are indented one level too
much, so remove the excess indentation.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index df58679..c2da10c 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -1603,10 +1603,10 @@ static int pci230_ai_check_chanlist(struct comedi_device *dev,
if (subseq_len > 0 &&
cmd->chanlist[i % subseq_len] != chanspec) {
- dev_dbg(dev->class_dev,
- "%s: channel numbers must increase or sequence must repeat exactly\n",
- __func__);
- return -EINVAL;
+ dev_dbg(dev->class_dev,
+ "%s: channel numbers must increase or sequence must repeat exactly\n",
+ __func__);
+ return -EINVAL;
}
if (aref != prev_aref) {
--
2.0.0
Since anything non-zero is logically "true", don't bother doing
"not-equal" comparisons with zero.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 75 +++++++++++++--------------
1 file changed, 36 insertions(+), 39 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 311c497..4222e28 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -672,16 +672,15 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
ok = 1;
claimed = 0;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES) && (res_mask != 0);
- b <<= 1, i++) {
- if ((res_mask & b) != 0) {
+ for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++) {
+ if (res_mask & b) {
res_mask &= ~b;
if (devpriv->res_owner[i] == OWNER_NONE) {
devpriv->res_owner[i] = owner;
claimed |= b;
} else if (devpriv->res_owner[i] != owner) {
- for (b = 1, i = 0; claimed != 0; b <<= 1, i++) {
- if ((claimed & b) != 0) {
+ for (b = 1, i = 0; claimed; b <<= 1, i++) {
+ if (claimed & b) {
devpriv->res_owner[i] =
OWNER_NONE;
claimed &= ~b;
@@ -711,9 +710,8 @@ static void put_resources(struct comedi_device *dev, unsigned int res_mask,
unsigned long irqflags;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES) && (res_mask != 0);
- b <<= 1, i++) {
- if ((res_mask & b) != 0) {
+ for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++) {
+ if (res_mask & b) {
res_mask &= ~b;
if (devpriv->res_owner[i] == owner)
devpriv->res_owner[i] = OWNER_NONE;
@@ -1086,7 +1084,7 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
* External trigger - for PCI230+ hardware version 2 onwards.
*/
/* Trigger number must be 0. */
- if ((cmd->scan_begin_arg & ~CR_FLAGS_MASK) != 0) {
+ if (cmd->scan_begin_arg & ~CR_FLAGS_MASK) {
cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
~CR_FLAGS_MASK);
err |= -EINVAL;
@@ -1095,8 +1093,8 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
* The only flags allowed are CR_EDGE and CR_INVERT.
* The CR_EDGE flag is ignored.
*/
- if ((cmd->scan_begin_arg &
- (CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT))) != 0) {
+ if (cmd->scan_begin_arg &
+ (CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT))) {
cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
CR_FLAGS_MASK &
~(CR_EDGE | CR_INVERT));
@@ -1258,7 +1256,7 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
}
if (events == 0) {
/* Check for FIFO underrun. */
- if ((dacstat & PCI230P2_DAC_FIFO_UNDERRUN_LATCHED) != 0) {
+ if (dacstat & PCI230P2_DAC_FIFO_UNDERRUN_LATCHED) {
dev_err(dev->class_dev, "AO FIFO underrun\n");
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
}
@@ -1275,11 +1273,11 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
}
if (events == 0) {
/* Determine how much room is in the FIFO (in samples). */
- if ((dacstat & PCI230P2_DAC_FIFO_FULL) != 0)
+ if (dacstat & PCI230P2_DAC_FIFO_FULL)
room = PCI230P2_DAC_FIFOROOM_FULL;
- else if ((dacstat & PCI230P2_DAC_FIFO_HALF) != 0)
+ else if (dacstat & PCI230P2_DAC_FIFO_HALF)
room = PCI230P2_DAC_FIFOROOM_HALFTOFULL;
- else if ((dacstat & PCI230P2_DAC_FIFO_EMPTY) != 0)
+ else if (dacstat & PCI230P2_DAC_FIFO_EMPTY)
room = PCI230P2_DAC_FIFOROOM_EMPTY;
else
room = PCI230P2_DAC_FIFOROOM_ONETOHALF;
@@ -1317,13 +1315,12 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
}
/* Check if FIFO underrun occurred while writing to FIFO. */
dacstat = inw(dev->iobase + PCI230_DACCON);
- if ((dacstat & PCI230P2_DAC_FIFO_UNDERRUN_LATCHED) != 0) {
+ if (dacstat & PCI230P2_DAC_FIFO_UNDERRUN_LATCHED) {
dev_err(dev->class_dev, "AO FIFO underrun\n");
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
}
}
- if ((events &
- (COMEDI_CB_EOA | COMEDI_CB_ERROR | COMEDI_CB_OVERFLOW)) != 0) {
+ if (events & (COMEDI_CB_EOA | COMEDI_CB_ERROR | COMEDI_CB_OVERFLOW)) {
/* Stopping AO due to completion or error. */
pci230_ao_stop(dev, s);
running = 0;
@@ -1341,7 +1338,7 @@ static int pci230_ao_inttrig_scan_begin(struct comedi_device *dev,
struct pci230_private *devpriv = dev->private;
unsigned long irqflags;
- if (trig_num != 0)
+ if (trig_num)
return -EINVAL;
spin_lock_irqsave(&devpriv->ao_stop_spinlock, irqflags);
@@ -1656,7 +1653,7 @@ static int pci230_ai_check_chanlist(struct comedi_device *dev,
if (subseq_len == 0)
subseq_len = cmd->chanlist_len;
- if ((cmd->chanlist_len % subseq_len) != 0) {
+ if (cmd->chanlist_len % subseq_len) {
dev_dbg(dev->class_dev,
"%s: sequence must repeat exactly\n", __func__);
return -EINVAL;
@@ -1674,7 +1671,7 @@ static int pci230_ai_check_chanlist(struct comedi_device *dev,
* the bug, but the second one does, and we can't tell them apart!
*/
if (devpriv->hwver > 0 && devpriv->hwver < 4) {
- if (subseq_len > 1 && CR_CHAN(cmd->chanlist[0]) != 0) {
+ if (subseq_len > 1 && CR_CHAN(cmd->chanlist[0])) {
dev_info(dev->class_dev,
"amplc_pci230: ai_cmdtest: Buggy PCI230+/260+ h/w version %u requires first channel of multi-channel sequence to be 0 (corrected in h/w version 4)\n",
devpriv->hwver);
@@ -1786,9 +1783,9 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* convert_arg == (CR_EDGE | CR_INVERT | 0)
* => trigger on -ve edge.
*/
- if ((cmd->convert_arg & CR_FLAGS_MASK) != 0) {
+ if (cmd->convert_arg & CR_FLAGS_MASK) {
/* Trigger number must be 0. */
- if ((cmd->convert_arg & ~CR_FLAGS_MASK) != 0) {
+ if (cmd->convert_arg & ~CR_FLAGS_MASK) {
cmd->convert_arg = COMBINE(cmd->convert_arg, 0,
~CR_FLAGS_MASK);
err |= -EINVAL;
@@ -1829,13 +1826,13 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* scan_begin_arg==0 => use PPC0 input -> gate of CT0 -> gate
* of CT2 (sample convert trigger is CT2)
*/
- if ((cmd->scan_begin_arg & ~CR_FLAGS_MASK) != 0) {
+ if (cmd->scan_begin_arg & ~CR_FLAGS_MASK) {
cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
~CR_FLAGS_MASK);
err |= -EINVAL;
}
/* The only flag allowed is CR_EDGE, which is ignored. */
- if ((cmd->scan_begin_arg & CR_FLAGS_MASK & ~CR_EDGE) != 0) {
+ if (cmd->scan_begin_arg & CR_FLAGS_MASK & ~CR_EDGE) {
cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
CR_FLAGS_MASK & ~CR_EDGE);
err |= -EINVAL;
@@ -1898,7 +1895,7 @@ static void pci230_ai_update_fifo_trigger_level(struct comedi_device *dev,
unsigned short triglev;
unsigned short adccon;
- if ((cmd->flags & TRIG_WAKE_EOS) != 0) {
+ if (cmd->flags & TRIG_WAKE_EOS) {
/* Wake at end of scan. */
wake = scanlen - devpriv->ai_scan_pos;
} else {
@@ -1939,7 +1936,7 @@ static int pci230_ai_inttrig_convert(struct comedi_device *dev,
struct pci230_private *devpriv = dev->private;
unsigned long irqflags;
- if (trig_num != 0)
+ if (trig_num)
return -EINVAL;
spin_lock_irqsave(&devpriv->ai_stop_spinlock, irqflags);
@@ -1986,7 +1983,7 @@ static int pci230_ai_inttrig_scan_begin(struct comedi_device *dev,
unsigned long irqflags;
unsigned char zgat;
- if (trig_num != 0)
+ if (trig_num)
return -EINVAL;
spin_lock_irqsave(&devpriv->ai_stop_spinlock, irqflags);
@@ -2088,7 +2085,7 @@ static void pci230_ai_start(struct comedi_device *dev,
conv = PCI230_ADC_TRIG_Z2CT2;
break;
case TRIG_EXT:
- if ((cmd->convert_arg & CR_EDGE) != 0) {
+ if (cmd->convert_arg & CR_EDGE) {
if ((cmd->convert_arg & CR_INVERT) == 0) {
/* Trigger on +ve edge. */
conv = PCI230_ADC_TRIG_EXTP;
@@ -2098,7 +2095,7 @@ static void pci230_ai_start(struct comedi_device *dev,
}
} else {
/* Backwards compatibility. */
- if (cmd->convert_arg != 0) {
+ if (cmd->convert_arg) {
/* Trigger on +ve edge. */
conv = PCI230_ADC_TRIG_EXTP;
} else {
@@ -2252,7 +2249,7 @@ static void pci230_handle_ai(struct comedi_device *dev,
if (fifoamount == 0) {
/* Read FIFO state. */
status_fifo = inw(dev->iobase + PCI230_ADCCON);
- if ((status_fifo & PCI230_ADC_FIFO_FULL_LATCHED) != 0) {
+ if (status_fifo & PCI230_ADC_FIFO_FULL_LATCHED) {
/*
* Report error otherwise FIFO overruns will go
* unnoticed by the caller.
@@ -2260,10 +2257,10 @@ static void pci230_handle_ai(struct comedi_device *dev,
dev_err(dev->class_dev, "AI FIFO overrun\n");
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
break;
- } else if ((status_fifo & PCI230_ADC_FIFO_EMPTY) != 0) {
+ } else if (status_fifo & PCI230_ADC_FIFO_EMPTY) {
/* FIFO empty. */
break;
- } else if ((status_fifo & PCI230_ADC_FIFO_HALF) != 0) {
+ } else if (status_fifo & PCI230_ADC_FIFO_HALF) {
/* FIFO half full. */
fifoamount = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else {
@@ -2304,8 +2301,8 @@ static void pci230_handle_ai(struct comedi_device *dev,
events |= COMEDI_CB_BLOCK;
}
async->events |= events;
- if ((async->events & (COMEDI_CB_EOA | COMEDI_CB_ERROR |
- COMEDI_CB_OVERFLOW)) != 0) {
+ if (async->events & (COMEDI_CB_EOA | COMEDI_CB_ERROR |
+ COMEDI_CB_OVERFLOW)) {
/* disable hardware conversions */
pci230_ai_stop(dev, s);
} else {
@@ -2561,19 +2558,19 @@ static irqreturn_t pci230_interrupt(int irq, void *d)
* two.
*/
- if ((valid_status_int & PCI230_INT_ZCLK_CT1) != 0) {
+ if (valid_status_int & PCI230_INT_ZCLK_CT1) {
s = dev->write_subdev;
pci230_handle_ao_nofifo(dev, s);
comedi_event(dev, s);
}
- if ((valid_status_int & PCI230P2_INT_DAC) != 0) {
+ if (valid_status_int & PCI230P2_INT_DAC) {
s = dev->write_subdev;
pci230_handle_ao_fifo(dev, s);
comedi_event(dev, s);
}
- if ((valid_status_int & PCI230_INT_ADC) != 0) {
+ if (valid_status_int & PCI230_INT_ADC) {
s = dev->read_subdev;
pci230_handle_ai(dev, s);
comedi_event(dev, s);
@@ -2741,7 +2738,7 @@ static int pci230_attach_common(struct comedi_device *dev,
}
}
outw(extfunc, dev->iobase + PCI230P_EXTFUNC);
- if ((extfunc & PCI230P2_EXTFUNC_DACFIFO) != 0) {
+ if (extfunc & PCI230P2_EXTFUNC_DACFIFO) {
/*
* Temporarily enable DAC FIFO, reset it and disable
* FIFO wraparound.
--
2.0.0
The macro constants `PCI230_DAC_SETTLE`, `PCI230_ADC_SETTLE` and
`PCI230_MUX_SETTLE` are never used. Just remove them.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 13 -------------
1 file changed, 13 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 00d7a22..7983a0d 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -247,19 +247,6 @@
#define PCI230P2_DACEN 0x06 /* DAC channel enable (FIFO mode) */
/*
- * Convertor related constants.
- */
-/* Analogue output settling time in µs (DAC itself is 1µs nominally). */
-#define PCI230_DAC_SETTLE 5
-/*
- * Analogue input settling time in µs (ADC itself is 1.6µs nominally but we
- * poll anyway).
- */
-#define PCI230_ADC_SETTLE 1
-/* ADC MUX settling time in µS - 10µs for se, 20µs de. */
-#define PCI230_MUX_SETTLE 10
-
-/*
* DACCON read-write values.
*/
#define PCI230_DAC_OR_UNI (0<<0) /* Output range unipolar */
--
2.0.0
Reformat a load of comments to fit in with the preferred coding style,
including the copyright and driver description comments at the top of
the file.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 837 +++++++++++++++-----------
1 file changed, 489 insertions(+), 348 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index a61d990..cb86d04 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -1,188 +1,189 @@
- /*
- comedi/drivers/amplc_pci230.c
- Driver for Amplicon PCI230 and PCI260 Multifunction I/O boards.
-
- Copyright (C) 2001 Allan Willcox <[email protected]>
-
- COMEDI - Linux Control and Measurement Device Interface
- Copyright (C) 2000 David A. Schleef <[email protected]>
-
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation; either version 2 of the License, or
- (at your option) any later version.
+/*
+ * comedi/drivers/amplc_pci230.c
+ * Driver for Amplicon PCI230 and PCI260 Multifunction I/O boards.
+ *
+ * Copyright (C) 2001 Allan Willcox <[email protected]>
+ *
+ * COMEDI - Linux Control and Measurement Device Interface
+ * Copyright (C) 2000 David A. Schleef <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
- */
/*
-Driver: amplc_pci230
-Description: Amplicon PCI230, PCI260 Multifunction I/O boards
-Author: Allan Willcox <[email protected]>,
- Steve D Sharples <[email protected]>,
- Ian Abbott <[email protected]>
-Updated: Wed, 22 Oct 2008 12:34:49 +0100
-Devices: [Amplicon] PCI230 (pci230 or amplc_pci230),
- PCI230+ (pci230+ or amplc_pci230),
- PCI260 (pci260 or amplc_pci230), PCI260+ (pci260+ or amplc_pci230)
-Status: works
-
-Configuration options:
- [0] - PCI bus of device (optional).
- [1] - PCI slot of device (optional).
- If bus/slot is not specified, the first available PCI device
- will be used.
-
-Configuring a "amplc_pci230" will match any supported card and it will
-choose the best match, picking the "+" models if possible. Configuring
-a "pci230" will match a PCI230 or PCI230+ card and it will be treated as
-a PCI230. Configuring a "pci260" will match a PCI260 or PCI260+ card
-and it will be treated as a PCI260. Configuring a "pci230+" will match
-a PCI230+ card. Configuring a "pci260+" will match a PCI260+ card.
-
-Subdevices:
-
- PCI230(+) PCI260(+)
- --------- ---------
- Subdevices 3 1
- 0 AI AI
- 1 AO
- 2 DIO
-
-AI Subdevice:
-
- The AI subdevice has 16 single-ended channels or 8 differential
- channels.
-
- The PCI230 and PCI260 cards have 12-bit resolution. The PCI230+ and
- PCI260+ cards have 16-bit resolution.
-
- For differential mode, use inputs 2N and 2N+1 for channel N (e.g. use
- inputs 14 and 15 for channel 7). If the card is physically a PCI230
- or PCI260 then it actually uses a "pseudo-differential" mode where the
- inputs are sampled a few microseconds apart. The PCI230+ and PCI260+
- use true differential sampling. Another difference is that if the
- card is physically a PCI230 or PCI260, the inverting input is 2N,
- whereas for a PCI230+ or PCI260+ the inverting input is 2N+1. So if a
- PCI230 is physically replaced by a PCI230+ (or a PCI260 with a
- PCI260+) and differential mode is used, the differential inputs need
- to be physically swapped on the connector.
-
- The following input ranges are supported:
-
- 0 => [-10, +10] V
- 1 => [-5, +5] V
- 2 => [-2.5, +2.5] V
- 3 => [-1.25, +1.25] V
- 4 => [0, 10] V
- 5 => [0, 5] V
- 6 => [0, 2.5] V
-
-AI Commands:
-
- +=========+==============+===========+============+==========+
- |start_src|scan_begin_src|convert_src|scan_end_src| stop_src |
- +=========+==============+===========+============+==========+
- |TRIG_NOW | TRIG_FOLLOW |TRIG_TIMER | TRIG_COUNT |TRIG_NONE |
- |TRIG_INT | |TRIG_EXT(3)| |TRIG_COUNT|
- | | |TRIG_INT | | |
- | |--------------|-----------| | |
- | | TRIG_TIMER(1)|TRIG_TIMER | | |
- | | TRIG_EXT(2) | | | |
- | | TRIG_INT | | | |
- +---------+--------------+-----------+------------+----------+
-
- Note 1: If AI command and AO command are used simultaneously, only
- one may have scan_begin_src == TRIG_TIMER.
-
- Note 2: For PCI230 and PCI230+, scan_begin_src == TRIG_EXT uses
- DIO channel 16 (pin 49) which will need to be configured as
- a digital input. For PCI260+, the EXTTRIG/EXTCONVCLK input
- (pin 17) is used instead. For PCI230, scan_begin_src ==
- TRIG_EXT is not supported. The trigger is a rising edge
- on the input.
-
- Note 3: For convert_src == TRIG_EXT, the EXTTRIG/EXTCONVCLK input
- (pin 25 on PCI230(+), pin 17 on PCI260(+)) is used. The
- convert_arg value is interpreted as follows:
-
- convert_arg == (CR_EDGE | 0) => rising edge
- convert_arg == (CR_EDGE | CR_INVERT | 0) => falling edge
- convert_arg == 0 => falling edge (backwards compatibility)
- convert_arg == 1 => rising edge (backwards compatibility)
-
- All entries in the channel list must use the same analogue reference.
- If the analogue reference is not AREF_DIFF (not differential) each
- pair of channel numbers (0 and 1, 2 and 3, etc.) must use the same
- input range. The input ranges used in the sequence must be all
- bipolar (ranges 0 to 3) or all unipolar (ranges 4 to 6). The channel
- sequence must consist of 1 or more identical subsequences. Within the
- subsequence, channels must be in ascending order with no repeated
- channels. For example, the following sequences are valid: 0 1 2 3
- (single valid subsequence), 0 2 3 5 0 2 3 5 (repeated valid
- subsequence), 1 1 1 1 (repeated valid subsequence). The following
- sequences are invalid: 0 3 2 1 (invalid subsequence), 0 2 3 5 0 2 3
- (incompletely repeated subsequence). Some versions of the PCI230+ and
- PCI260+ have a bug that requires a subsequence longer than one entry
- long to include channel 0.
-
-AO Subdevice:
-
- The AO subdevice has 2 channels with 12-bit resolution.
-
- The following output ranges are supported:
-
- 0 => [0, 10] V
- 1 => [-10, +10] V
-
-AO Commands:
-
- +=========+==============+===========+============+==========+
- |start_src|scan_begin_src|convert_src|scan_end_src| stop_src |
- +=========+==============+===========+============+==========+
- |TRIG_INT | TRIG_TIMER(1)| TRIG_NOW | TRIG_COUNT |TRIG_NONE |
- | | TRIG_EXT(2) | | |TRIG_COUNT|
- | | TRIG_INT | | | |
- +---------+--------------+-----------+------------+----------+
-
- Note 1: If AI command and AO command are used simultaneously, only
- one may have scan_begin_src == TRIG_TIMER.
-
- Note 2: scan_begin_src == TRIG_EXT is only supported if the card is
- configured as a PCI230+ and is only supported on later
- versions of the card. As a card configured as a PCI230+ is
- not guaranteed to support external triggering, please consider
- this support to be a bonus. It uses the EXTTRIG/ EXTCONVCLK
- input (PCI230+ pin 25). Triggering will be on the rising edge
- unless the CR_INVERT flag is set in scan_begin_arg.
-
- The channels in the channel sequence must be in ascending order with
- no repeats. All entries in the channel sequence must use the same
- output range.
-
-DIO Subdevice:
-
- The DIO subdevice is a 8255 chip providing 24 DIO channels. The DIO
- channels are configurable as inputs or outputs in four groups:
-
- Port A - channels 0 to 7
- Port B - channels 8 to 15
- Port CL - channels 16 to 19
- Port CH - channels 20 to 23
-
- Only mode 0 of the 8255 chip is supported.
-
- Bit 0 of port C (DIO channel 16) is also used as an external scan
- trigger input for AI commands on PCI230 and PCI230+, so would need to
- be configured as an input to use it for that purpose.
-*/
+ * Driver: amplc_pci230
+ * Description: Amplicon PCI230, PCI260 Multifunction I/O boards
+ * Author: Allan Willcox <[email protected]>,
+ * Steve D Sharples <[email protected]>,
+ * Ian Abbott <[email protected]>
+ * Updated: Wed, 22 Oct 2008 12:34:49 +0100
+ * Devices: [Amplicon] PCI230 (pci230 or amplc_pci230),
+ * PCI230+ (pci230+ or amplc_pci230),
+ * PCI260 (pci260 or amplc_pci230), PCI260+ (pci260+ or amplc_pci230)
+ * Status: works
+ *
+ * Configuration options:
+ * [0] - PCI bus of device (optional).
+ * [1] - PCI slot of device (optional).
+ * If bus/slot is not specified, the first available PCI device
+ * will be used.
+ *
+ * Configuring a "amplc_pci230" will match any supported card and it will
+ * choose the best match, picking the "+" models if possible. Configuring
+ * a "pci230" will match a PCI230 or PCI230+ card and it will be treated as
+ * a PCI230. Configuring a "pci260" will match a PCI260 or PCI260+ card
+ * and it will be treated as a PCI260. Configuring a "pci230+" will match
+ * a PCI230+ card. Configuring a "pci260+" will match a PCI260+ card.
+ *
+ * Subdevices:
+ *
+ * PCI230(+) PCI260(+)
+ * --------- ---------
+ * Subdevices 3 1
+ * 0 AI AI
+ * 1 AO
+ * 2 DIO
+ *
+ * AI Subdevice:
+ *
+ * The AI subdevice has 16 single-ended channels or 8 differential
+ * channels.
+ *
+ * The PCI230 and PCI260 cards have 12-bit resolution. The PCI230+ and
+ * PCI260+ cards have 16-bit resolution.
+ *
+ * For differential mode, use inputs 2N and 2N+1 for channel N (e.g. use
+ * inputs 14 and 15 for channel 7). If the card is physically a PCI230
+ * or PCI260 then it actually uses a "pseudo-differential" mode where the
+ * inputs are sampled a few microseconds apart. The PCI230+ and PCI260+
+ * use true differential sampling. Another difference is that if the
+ * card is physically a PCI230 or PCI260, the inverting input is 2N,
+ * whereas for a PCI230+ or PCI260+ the inverting input is 2N+1. So if a
+ * PCI230 is physically replaced by a PCI230+ (or a PCI260 with a
+ * PCI260+) and differential mode is used, the differential inputs need
+ * to be physically swapped on the connector.
+ *
+ * The following input ranges are supported:
+ *
+ * 0 => [-10, +10] V
+ * 1 => [-5, +5] V
+ * 2 => [-2.5, +2.5] V
+ * 3 => [-1.25, +1.25] V
+ * 4 => [0, 10] V
+ * 5 => [0, 5] V
+ * 6 => [0, 2.5] V
+ *
+ * AI Commands:
+ *
+ * +=========+==============+===========+============+==========+
+ * |start_src|scan_begin_src|convert_src|scan_end_src| stop_src |
+ * +=========+==============+===========+============+==========+
+ * |TRIG_NOW | TRIG_FOLLOW |TRIG_TIMER | TRIG_COUNT |TRIG_NONE |
+ * |TRIG_INT | |TRIG_EXT(3)| |TRIG_COUNT|
+ * | | |TRIG_INT | | |
+ * | |--------------|-----------| | |
+ * | | TRIG_TIMER(1)|TRIG_TIMER | | |
+ * | | TRIG_EXT(2) | | | |
+ * | | TRIG_INT | | | |
+ * +---------+--------------+-----------+------------+----------+
+ *
+ * Note 1: If AI command and AO command are used simultaneously, only
+ * one may have scan_begin_src == TRIG_TIMER.
+ *
+ * Note 2: For PCI230 and PCI230+, scan_begin_src == TRIG_EXT uses
+ * DIO channel 16 (pin 49) which will need to be configured as
+ * a digital input. For PCI260+, the EXTTRIG/EXTCONVCLK input
+ * (pin 17) is used instead. For PCI230, scan_begin_src ==
+ * TRIG_EXT is not supported. The trigger is a rising edge
+ * on the input.
+ *
+ * Note 3: For convert_src == TRIG_EXT, the EXTTRIG/EXTCONVCLK input
+ * (pin 25 on PCI230(+), pin 17 on PCI260(+)) is used. The
+ * convert_arg value is interpreted as follows:
+ *
+ * convert_arg == (CR_EDGE | 0) => rising edge
+ * convert_arg == (CR_EDGE | CR_INVERT | 0) => falling edge
+ * convert_arg == 0 => falling edge (backwards compatibility)
+ * convert_arg == 1 => rising edge (backwards compatibility)
+ *
+ * All entries in the channel list must use the same analogue reference.
+ * If the analogue reference is not AREF_DIFF (not differential) each
+ * pair of channel numbers (0 and 1, 2 and 3, etc.) must use the same
+ * input range. The input ranges used in the sequence must be all
+ * bipolar (ranges 0 to 3) or all unipolar (ranges 4 to 6). The channel
+ * sequence must consist of 1 or more identical subsequences. Within the
+ * subsequence, channels must be in ascending order with no repeated
+ * channels. For example, the following sequences are valid: 0 1 2 3
+ * (single valid subsequence), 0 2 3 5 0 2 3 5 (repeated valid
+ * subsequence), 1 1 1 1 (repeated valid subsequence). The following
+ * sequences are invalid: 0 3 2 1 (invalid subsequence), 0 2 3 5 0 2 3
+ * (incompletely repeated subsequence). Some versions of the PCI230+ and
+ * PCI260+ have a bug that requires a subsequence longer than one entry
+ * long to include channel 0.
+ *
+ * AO Subdevice:
+ *
+ * The AO subdevice has 2 channels with 12-bit resolution.
+ * The following output ranges are supported:
+ * 0 => [0, 10] V
+ * 1 => [-10, +10] V
+ *
+ * AO Commands:
+ *
+ * +=========+==============+===========+============+==========+
+ * |start_src|scan_begin_src|convert_src|scan_end_src| stop_src |
+ * +=========+==============+===========+============+==========+
+ * |TRIG_INT | TRIG_TIMER(1)| TRIG_NOW | TRIG_COUNT |TRIG_NONE |
+ * | | TRIG_EXT(2) | | |TRIG_COUNT|
+ * | | TRIG_INT | | | |
+ * +---------+--------------+-----------+------------+----------+
+ *
+ * Note 1: If AI command and AO command are used simultaneously, only
+ * one may have scan_begin_src == TRIG_TIMER.
+ *
+ * Note 2: scan_begin_src == TRIG_EXT is only supported if the card is
+ * configured as a PCI230+ and is only supported on later
+ * versions of the card. As a card configured as a PCI230+ is
+ * not guaranteed to support external triggering, please consider
+ * this support to be a bonus. It uses the EXTTRIG/ EXTCONVCLK
+ * input (PCI230+ pin 25). Triggering will be on the rising edge
+ * unless the CR_INVERT flag is set in scan_begin_arg.
+ *
+ * The channels in the channel sequence must be in ascending order with
+ * no repeats. All entries in the channel sequence must use the same
+ * output range.
+ *
+ * DIO Subdevice:
+ *
+ * The DIO subdevice is a 8255 chip providing 24 DIO channels. The DIO
+ * channels are configurable as inputs or outputs in four groups:
+ *
+ * Port A - channels 0 to 7
+ * Port B - channels 8 to 15
+ * Port CL - channels 16 to 19
+ * Port CH - channels 20 to 23
+ *
+ * Only mode 0 of the 8255 chip is supported.
+ *
+ * Bit 0 of port C (DIO channel 16) is also used as an external scan
+ * trigger input for AI commands on PCI230 and PCI230+, so would need to
+ * be configured as an input to use it for that purpose.
+ */
+
/*
-Extra triggered scan functionality, interrupt bug-fix added by Steve Sharples.
-Support for PCI230+/260+, more triggered scan functionality, and workarounds
-for (or detection of) various hardware problems added by Ian Abbott.
-*/
+ * Extra triggered scan functionality, interrupt bug-fix added by Steve
+ * Sharples. Support for PCI230+/260+, more triggered scan functionality,
+ * and workarounds for (or detection of) various hardware problems added
+ * by Ian Abbott.
+ */
#include <linux/module.h>
#include <linux/pci.h>
@@ -195,12 +196,16 @@ for (or detection of) various hardware problems added by Ian Abbott.
#include "8253.h"
#include "8255.h"
-/* PCI230 PCI configuration register information */
+/*
+ * PCI230 PCI configuration register information
+ */
#define PCI_DEVICE_ID_PCI230 0x0000
#define PCI_DEVICE_ID_PCI260 0x0006
#define PCI_DEVICE_ID_INVALID 0xffff
-/* PCI230 i/o space 1 registers. */
+/*
+ * PCI230 i/o space 1 registers.
+ */
#define PCI230_PPI_X_BASE 0x00 /* User PPI (82C55) base */
#define PCI230_PPI_X_A 0x00 /* User PPI (82C55) port A */
#define PCI230_PPI_X_B 0x01 /* User PPI (82C55) port B */
@@ -216,7 +221,9 @@ for (or detection of) various hardware problems added by Ian Abbott.
#define PCI230_INT_SCE 0x1E /* Interrupt source mask (w) */
#define PCI230_INT_STAT 0x1E /* Interrupt status (r) */
-/* PCI230 i/o space 2 registers. */
+/*
+ * PCI230 i/o space 2 registers.
+ */
#define PCI230_DACCON 0x00 /* DAC control */
#define PCI230_DACOUT1 0x02 /* DAC channel 0 (w) */
#define PCI230_DACOUT2 0x04 /* DAC channel 1 (w) (not FIFO mode) */
@@ -239,24 +246,34 @@ for (or detection of) various hardware problems added by Ian Abbott.
#define PCI230P2_DACSWTRIG 0x02 /* DAC soft trigger (FIFO mode) (r) */
#define PCI230P2_DACEN 0x06 /* DAC channel enable (FIFO mode) */
-/* Convertor related constants. */
-#define PCI230_DAC_SETTLE 5 /* Analogue output settling time in µs */
- /* (DAC itself is 1µs nominally). */
-#define PCI230_ADC_SETTLE 1 /* Analogue input settling time in µs */
- /* (ADC itself is 1.6µs nominally but we poll
- * anyway). */
-#define PCI230_MUX_SETTLE 10 /* ADC MUX settling time in µS */
- /* - 10µs for se, 20µs de. */
+/*
+ * Convertor related constants.
+ */
+/* Analogue output settling time in µs (DAC itself is 1µs nominally). */
+#define PCI230_DAC_SETTLE 5
+/*
+ * Analogue input settling time in µs (ADC itself is 1.6µs nominally but we
+ * poll anyway).
+ */
+#define PCI230_ADC_SETTLE 1
+/* ADC MUX settling time in µS - 10µs for se, 20µs de. */
+#define PCI230_MUX_SETTLE 10
-/* DACCON read-write values. */
+/*
+ * DACCON read-write values.
+ */
#define PCI230_DAC_OR_UNI (0<<0) /* Output range unipolar */
#define PCI230_DAC_OR_BIP (1<<0) /* Output range bipolar */
#define PCI230_DAC_OR_MASK (1<<0)
-/* The following applies only if DAC FIFO support is enabled in the EXTFUNC
- * register (and only for PCI230+ hardware version 2 onwards). */
+/*
+ * The following applies only if DAC FIFO support is enabled in the EXTFUNC
+ * register (and only for PCI230+ hardware version 2 onwards).
+ */
#define PCI230P2_DAC_FIFO_EN (1<<8) /* FIFO enable */
-/* The following apply only if the DAC FIFO is enabled (and only for PCI230+
- * hardware version 2 onwards). */
+/*
+ * The following apply only if the DAC FIFO is enabled (and only for PCI230+
+ * hardware version 2 onwards).
+ */
#define PCI230P2_DAC_TRIG_NONE (0<<2) /* No trigger */
#define PCI230P2_DAC_TRIG_SW (1<<2) /* Software trigger trigger */
#define PCI230P2_DAC_TRIG_EXTP (2<<2) /* EXTTRIG +ve edge trigger */
@@ -274,22 +291,32 @@ for (or detection of) various hardware problems added by Ian Abbott.
#define PCI230P2_DAC_INT_FIFO_FULL (5<<9)
#define PCI230P2_DAC_INT_FIFO_MASK (7<<9)
-/* DACCON read-only values. */
+/*
+ * DACCON read-only values.
+ */
#define PCI230_DAC_BUSY (1<<1) /* DAC busy. */
-/* The following apply only if the DAC FIFO is enabled (and only for PCI230+
- * hardware version 2 onwards). */
+/*
+ * The following apply only if the DAC FIFO is enabled (and only for PCI230+
+ * hardware version 2 onwards).
+ */
#define PCI230P2_DAC_FIFO_UNDERRUN_LATCHED (1<<5) /* Underrun error */
#define PCI230P2_DAC_FIFO_EMPTY (1<<13) /* FIFO empty */
#define PCI230P2_DAC_FIFO_FULL (1<<14) /* FIFO full */
#define PCI230P2_DAC_FIFO_HALF (1<<15) /* FIFO half full */
-/* DACCON write-only, transient values. */
-/* The following apply only if the DAC FIFO is enabled (and only for PCI230+
- * hardware version 2 onwards). */
+/*
+ * DACCON write-only, transient values.
+ */
+/*
+ * The following apply only if the DAC FIFO is enabled (and only for PCI230+
+ * hardware version 2 onwards).
+ */
#define PCI230P2_DAC_FIFO_UNDERRUN_CLEAR (1<<5) /* Clear underrun */
#define PCI230P2_DAC_FIFO_RESET (1<<12) /* FIFO reset */
-/* PCI230+ hardware version 2 DAC FIFO levels. */
+/*
+ * PCI230+ hardware version 2 DAC FIFO levels.
+ */
#define PCI230P2_DAC_FIFOLEVEL_HALF 512
#define PCI230P2_DAC_FIFOLEVEL_FULL 1024
/* Free space in DAC FIFO. */
@@ -299,7 +326,9 @@ for (or detection of) various hardware problems added by Ian Abbott.
#define PCI230P2_DAC_FIFOROOM_HALFTOFULL 1
#define PCI230P2_DAC_FIFOROOM_FULL 0
-/* ADCCON read/write values. */
+/*
+ * ADCCON read/write values.
+ */
#define PCI230_ADC_TRIG_NONE (0<<0) /* No trigger */
#define PCI230_ADC_TRIG_SW (1<<0) /* Software trigger trigger */
#define PCI230_ADC_TRIG_EXTP (2<<0) /* EXTTRIG +ve edge trigger */
@@ -324,31 +353,41 @@ for (or detection of) various hardware problems added by Ian Abbott.
#define PCI230P_ADC_INT_FIFO_THRESH (7<<9) /* FIFO interrupt threshold */
#define PCI230_ADC_INT_FIFO_MASK (7<<9)
-/* ADCCON write-only, transient values. */
+/*
+ * ADCCON write-only, transient values.
+ */
#define PCI230_ADC_FIFO_RESET (1<<12) /* FIFO reset */
#define PCI230_ADC_GLOB_RESET (1<<13) /* Global reset */
-/* ADCCON read-only values. */
+/*
+ * ADCCON read-only values.
+ */
#define PCI230_ADC_BUSY (1<<15) /* ADC busy */
#define PCI230_ADC_FIFO_EMPTY (1<<12) /* FIFO empty */
#define PCI230_ADC_FIFO_FULL (1<<13) /* FIFO full */
#define PCI230_ADC_FIFO_HALF (1<<14) /* FIFO half full */
#define PCI230_ADC_FIFO_FULL_LATCHED (1<<5) /* Indicates overrun occurred */
-/* PCI230 ADC FIFO levels. */
+/*
+ * PCI230 ADC FIFO levels.
+ */
#define PCI230_ADC_FIFOLEVEL_HALFFULL 2049 /* Value for FIFO half full */
#define PCI230_ADC_FIFOLEVEL_FULL 4096 /* FIFO size */
-/* Value to write to ADCSWTRIG to trigger ADC conversion in software trigger
- * mode. Can be anything. */
+/*
+ * Value to write to ADCSWTRIG to trigger ADC conversion in software trigger
+ * mode. Can be anything.
+ */
#define PCI230_ADC_CONV 0xffff
-/* PCI230+ EXTFUNC values. */
+/*
+ * PCI230+ EXTFUNC values.
+ */
+/* Route EXTTRIG pin to external gate inputs. */
#define PCI230P_EXTFUNC_GAT_EXTTRIG (1<<0)
- /* Route EXTTRIG pin to external gate inputs. */
/* PCI230+ hardware version 2 values. */
+/* Allow DAC FIFO to be enabled. */
#define PCI230P2_EXTFUNC_DACFIFO (1<<1)
- /* Allow DAC FIFO to be enabled. */
/*
* Counter/timer clock input configuration sources.
@@ -392,7 +431,9 @@ for (or detection of) various hardware problems added by Ian Abbott.
* Z2-CT2 Z2-CT1-OUT /Z2-CT0-OUT
*/
-/* Interrupt enables/status register values. */
+/*
+ * Interrupt enables/status register values.
+ */
#define PCI230_INT_DISABLE 0
#define PCI230_INT_PPI_C0 (1<<0)
#define PCI230_INT_PPI_C3 (1<<1)
@@ -401,10 +442,12 @@ for (or detection of) various hardware problems added by Ian Abbott.
/* For PCI230+ hardware version 2 when DAC FIFO enabled. */
#define PCI230P2_INT_DAC (1<<4)
+/* Assumes bits numbered with zero offset, ie. 0-15 */
#define PCI230_TEST_BIT(val, n) ((val>>n)&1)
- /* Assumes bits numbered with zero offset, ie. 0-15 */
-/* (Potentially) shared resources and their owners */
+/*
+ * (Potentially) shared resources and their owners
+ */
enum {
RES_Z2CT0, /* Z2-CT0 */
RES_Z2CT1, /* Z2-CT1 */
@@ -491,9 +534,11 @@ static const struct pci230_board pci230_boards[] = {
},
};
-/* this structure is for data unique to this hardware driver. If
- several hardware drivers keep similar information in this structure,
- feel free to suggest moving the variable to the struct comedi_device struct. */
+/*
+ * This structure is for data unique to this hardware driver. If
+ * several hardware drivers keep similar information in this structure,
+ * feel free to suggest moving the variable to the struct comedi_device struct.
+ */
struct pci230_private {
spinlock_t isr_spinlock; /* Interrupt spin lock */
spinlock_t res_spinlock; /* Shared resources spin lock */
@@ -502,24 +547,24 @@ struct pci230_private {
unsigned long state; /* State flags */
unsigned long iobase1; /* PCI230's I/O space 1 */
unsigned int ao_readback[2]; /* Used for AO readback */
- unsigned int ai_scan_count; /* Number of analogue input scans
- * remaining. */
- unsigned int ai_scan_pos; /* Current position within analogue
- * input scan */
- unsigned int ao_scan_count; /* Number of analogue output scans
- * remaining. */
+ /* Number of analogue input scans remaining. */
+ unsigned int ai_scan_count;
+ /* Current position within analogue input scan */
+ unsigned int ai_scan_pos;
+ /* Number of analogue output scans remaining. */
+ unsigned int ao_scan_count;
int intr_cpuid; /* ID of CPU running interrupt routine. */
unsigned short hwver; /* Hardware version (for '+' models). */
unsigned short adccon; /* ADCCON register value. */
unsigned short daccon; /* DACCON register value. */
- unsigned short adcfifothresh; /* ADC FIFO programmable interrupt
- * level threshold (PCI230+/260+). */
+ /* ADC FIFO programmable interrupt level threshold (PCI230+/260+). */
+ unsigned short adcfifothresh;
unsigned short adcg; /* ADCG register value. */
unsigned char int_en; /* Interrupt enables bits. */
- unsigned char ai_bipolar; /* Set if bipolar input range so we
- * know to mangle it. */
- unsigned char ao_bipolar; /* Set if bipolar output range so we
- * know to mangle it. */
+ /* Set if bipolar input range so we know to mangle it. */
+ unsigned char ai_bipolar;
+ /* Set if bipolar output range so we know to mangle it. */
+ unsigned char ao_bipolar;
unsigned char ier; /* Copy of interrupt enables/status register. */
unsigned char intr_running; /* Flag set in interrupt routine. */
unsigned char res_owner[NUM_RESOURCES]; /* Shared resource owners. */
@@ -572,13 +617,16 @@ static unsigned short pci230_ai_read(struct comedi_device *dev)
/* Read sample. */
data = inw(dev->iobase + PCI230_ADCDATA);
- /* PCI230 is 12 bit - stored in upper bits of 16 bit register (lower
- * four bits reserved for expansion). */
- /* PCI230+ is 16 bit AI. */
+ /*
+ * PCI230 is 12 bit - stored in upper bits of 16 bit register
+ * (lower four bits reserved for expansion). PCI230+ is 16 bit AI.
+ */
data = data >> (16 - thisboard->ai_bits);
- /* If a bipolar range was specified, mangle it (twos
- * complement->straight binary). */
+ /*
+ * If a bipolar range was specified, mangle it
+ * (twos complement->straight binary).
+ */
if (devpriv->ai_bipolar)
data ^= 1 << (thisboard->ai_bits - 1);
@@ -591,14 +639,17 @@ static inline unsigned short pci230_ao_mangle_datum(struct comedi_device *dev,
const struct pci230_board *thisboard = comedi_board(dev);
struct pci230_private *devpriv = dev->private;
- /* If a bipolar range was specified, mangle it (straight binary->twos
- * complement). */
+ /*
+ * If a bipolar range was specified, mangle it
+ * (straight binary->twos complement).
+ */
if (devpriv->ao_bipolar)
datum ^= 1 << (thisboard->ao_bits - 1);
- /* PCI230 is 12 bit - stored in upper bits of 16 bit register (lower
- * four bits reserved for expansion). */
- /* PCI230+ is also 12 bit AO. */
+ /*
+ * PCI230 is 12 bit - stored in upper bits of 16 bit register (lower
+ * four bits reserved for expansion). PCI230+ is also 12 bit AO.
+ */
datum <<= (16 - thisboard->ao_bits);
return datum;
}
@@ -730,8 +781,10 @@ static unsigned int divide_ns(uint64_t ns, unsigned int timebase,
return div > UINT_MAX ? UINT_MAX : (unsigned int)div;
}
-/* Given desired period in ns, returns the required internal clock source
- * and gets the initial count. */
+/*
+ * Given desired period in ns, returns the required internal clock source
+ * and gets the initial count.
+ */
static unsigned int pci230_choose_clk_count(uint64_t ns, unsigned int *count,
unsigned int flags)
{
@@ -824,7 +877,8 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
}
}
- /* Use Z2-CT2 as a conversion trigger instead of the built-in
+ /*
+ * Use Z2-CT2 as a conversion trigger instead of the built-in
* software trigger, as otherwise triggering of differential channels
* doesn't work properly for some versions of PCI230/260. Also set
* FIFO mode because the ADC busy bit only works for software triggers.
@@ -837,12 +891,16 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
/* Differential. */
gainshift = chan * 2;
if (devpriv->hwver == 0) {
- /* Original PCI230/260 expects both inputs of the
- * differential channel to be enabled. */
+ /*
+ * Original PCI230/260 expects both inputs of the
+ * differential channel to be enabled.
+ */
adcen = 3 << gainshift;
} else {
- /* PCI230+/260+ expects only one input of the
- * differential channel to be enabled. */
+ /*
+ * PCI230+/260+ expects only one input of the
+ * differential channel to be enabled.
+ */
adcen = 1 << gainshift;
}
adccon |= PCI230_ADC_IM_DIF;
@@ -860,8 +918,10 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
adccon |= PCI230_ADC_IR_UNI;
- /* Enable only this channel in the scan list - otherwise by default
- * we'll get one sample from each channel. */
+ /*
+ * Enable only this channel in the scan list - otherwise by default
+ * we'll get one sample from each channel.
+ */
outw(adcen, dev->iobase + PCI230_ADCEN);
/* Set gain for channel. */
@@ -873,8 +933,10 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
/* Convert n samples */
for (n = 0; n < insn->n; n++) {
- /* Trigger conversion by toggling Z2-CT2 output (finish with
- * output high). */
+ /*
+ * Trigger conversion by toggling Z2-CT2 output
+ * (finish with output high).
+ */
i8254_set_mode(devpriv->iobase1 + PCI230_Z2_CT_BASE, 0, 2,
I8254_MODE0);
i8254_set_mode(devpriv->iobase1 + PCI230_Z2_CT_BASE, 0, 2,
@@ -908,13 +970,17 @@ static int pci230_ao_winsn(struct comedi_device *dev,
chan = CR_CHAN(insn->chanspec);
range = CR_RANGE(insn->chanspec);
- /* Set range - see analogue output range table; 0 => unipolar 10V,
- * 1 => bipolar +/-10V range scale */
+ /*
+ * Set range - see analogue output range table; 0 => unipolar 10V,
+ * 1 => bipolar +/-10V range scale
+ */
devpriv->ao_bipolar = pci230_ao_bipolar[range];
outw(range, dev->iobase + PCI230_DACCON);
- /* Writing a list of values to an AO channel is probably not
- * very useful, but that's how the interface is defined. */
+ /*
+ * Writing a list of values to an AO channel is probably not
+ * very useful, but that's how the interface is defined.
+ */
for (i = 0; i < insn->n; i++) {
/* Write value to DAC and store it. */
pci230_ao_write_nofifo(dev, data[i], chan);
@@ -924,8 +990,10 @@ static int pci230_ao_winsn(struct comedi_device *dev,
return i;
}
-/* AO subdevices should have a read insn as well as a write insn.
- * Usually this means copying a value stored in devpriv. */
+/*
+ * AO subdevices should have a read insn as well as a write insn.
+ * Usually this means copying a value stored in devpriv.
+ */
static int pci230_ao_rinsn(struct comedi_device *dev,
struct comedi_subdevice *s, struct comedi_insn *insn,
unsigned int *data)
@@ -1026,10 +1094,11 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_arg_is(&cmd->start_arg, 0);
#define MAX_SPEED_AO 8000 /* 8000 ns => 125 kHz */
+/*
+ * Comedi limit due to unsigned int cmd. Driver limit =
+ * 2^16 (16bit * counter) * 1000000ns (1kHz onboard clock) = 65.536s
+ */
#define MIN_SPEED_AO 4294967295u /* 4294967295ns = 4.29s */
- /*- Comedi limit due to unsigned int cmd. Driver limit
- * = 2^16 (16bit * counter) * 1000000ns (1kHz onboard
- * clock) = 65.536s */
switch (cmd->scan_begin_src) {
case TRIG_TIMER:
@@ -1039,15 +1108,19 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
MIN_SPEED_AO);
break;
case TRIG_EXT:
- /* External trigger - for PCI230+ hardware version 2 onwards. */
+ /*
+ * External trigger - for PCI230+ hardware version 2 onwards.
+ */
/* Trigger number must be 0. */
if ((cmd->scan_begin_arg & ~CR_FLAGS_MASK) != 0) {
cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
~CR_FLAGS_MASK);
err |= -EINVAL;
}
- /* The only flags allowed are CR_EDGE and CR_INVERT. The
- * CR_EDGE flag is ignored. */
+ /*
+ * The only flags allowed are CR_EDGE and CR_INVERT.
+ * The CR_EDGE flag is ignored.
+ */
if ((cmd->scan_begin_arg
& (CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT))) != 0) {
cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
@@ -1069,9 +1142,7 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
if (err)
return 3;
- /* Step 4: fix up any arguments.
- * "argument conflict" returned by comedilib to user mode process
- * if this fails. */
+ /* Step 4: fix up any arguments */
if (cmd->scan_begin_src == TRIG_TIMER) {
tmp = cmd->scan_begin_arg;
@@ -1120,8 +1191,10 @@ static void pci230_ao_stop(struct comedi_device *dev,
/* Using DAC FIFO interrupt. */
intsrc = PCI230P2_INT_DAC;
}
- /* Disable interrupt and wait for interrupt routine to finish running
- * unless we are called from the interrupt routine. */
+ /*
+ * Disable interrupt and wait for interrupt routine to finish running
+ * unless we are called from the interrupt routine.
+ */
spin_lock_irqsave(&devpriv->isr_spinlock, irqflags);
devpriv->int_en &= ~intsrc;
while (devpriv->intr_running && devpriv->intr_cpuid != THISCPU) {
@@ -1134,8 +1207,10 @@ static void pci230_ao_stop(struct comedi_device *dev,
}
spin_unlock_irqrestore(&devpriv->isr_spinlock, irqflags);
if (devpriv->hwver >= 2) {
- /* Using DAC FIFO. Reset FIFO, clear underrun error,
- * disable FIFO. */
+ /*
+ * Using DAC FIFO. Reset FIFO, clear underrun error,
+ * disable FIFO.
+ */
devpriv->daccon &= PCI230_DAC_OR_MASK;
outw(devpriv->daccon | PCI230P2_DAC_FIFO_RESET
| PCI230P2_DAC_FIFO_UNDERRUN_CLEAR,
@@ -1213,9 +1288,11 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
dev_err(dev->class_dev, "AO FIFO underrun\n");
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
}
- /* Check for buffer underrun if FIFO less than half full
+ /*
+ * Check for buffer underrun if FIFO less than half full
* (otherwise there will be loads of "DAC FIFO not half full"
- * interrupts). */
+ * interrupts).
+ */
if ((num_scans == 0)
&& ((dacstat & PCI230P2_DAC_FIFO_HALF) == 0)) {
dev_err(dev->class_dev, "AO buffer underrun\n");
@@ -1251,9 +1328,11 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
if (cmd->stop_src == TRIG_COUNT) {
devpriv->ao_scan_count -= num_scans;
if (devpriv->ao_scan_count == 0) {
- /* All data for the command has been written
+ /*
+ * All data for the command has been written
* to FIFO. Set FIFO interrupt trigger level
- * to 'empty'. */
+ * to 'empty'.
+ */
devpriv->daccon = (devpriv->daccon
&
~PCI230P2_DAC_INT_FIFO_MASK)
@@ -1444,8 +1523,10 @@ static int pci230_ao_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
else /* TRIG_NONE, user calls cancel */
devpriv->ao_scan_count = 0;
- /* Set range - see analogue output range table; 0 => unipolar 10V,
- * 1 => bipolar +/-10V range scale */
+ /*
+ * Set range - see analogue output range table; 0 => unipolar 10V,
+ * 1 => bipolar +/-10V range scale
+ */
range = CR_RANGE(cmd->chanlist[0]);
devpriv->ao_bipolar = pci230_ao_bipolar[range];
daccon = devpriv->ao_bipolar ? PCI230_DAC_OR_BIP : PCI230_DAC_OR_UNI;
@@ -1480,9 +1561,11 @@ static int pci230_ao_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
& ~(PCI230P2_DAC_FIFO_RESET | PCI230P2_DAC_FIFO_UNDERRUN_CLEAR);
if (cmd->scan_begin_src == TRIG_TIMER) {
- /* Set the counter timer 1 to the specified scan frequency. */
- /* cmd->scan_begin_arg is sampling period in ns */
- /* gate it off for now. */
+ /*
+ * Set the counter timer 1 to the specified scan frequency.
+ * cmd->scan_begin_arg is sampling period in ns.
+ * Gate it off for now.
+ */
outb(GAT_CONFIG(1, GAT_GND),
devpriv->iobase1 + PCI230_ZGAT_SCE);
pci230_ct_setup_ns_mode(dev, 1, I8254_MODE3,
@@ -1688,17 +1771,20 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
#define MAX_SPEED_AI_SE 3200 /* PCI230 SE: 3200 ns => 312.5 kHz */
#define MAX_SPEED_AI_DIFF 8000 /* PCI230 DIFF: 8000 ns => 125 kHz */
#define MAX_SPEED_AI_PLUS 4000 /* PCI230+: 4000 ns => 250 kHz */
+/*
+ * Comedi limit due to unsigned int cmd. Driver limit =
+ * 2^16 (16bit * counter) * 1000000ns (1kHz onboard clock) = 65.536s
+ */
#define MIN_SPEED_AI 4294967295u /* 4294967295ns = 4.29s */
- /*- Comedi limit due to unsigned int cmd. Driver limit
- * = 2^16 (16bit * counter) * 1000000ns (1kHz onboard
- * clock) = 65.536s */
if (cmd->convert_src == TRIG_TIMER) {
unsigned int max_speed_ai;
if (devpriv->hwver == 0) {
- /* PCI230 or PCI260. Max speed depends whether
- * single-ended or pseudo-differential. */
+ /*
+ * PCI230 or PCI260. Max speed depends whether
+ * single-ended or pseudo-differential.
+ */
if (cmd->chanlist && (cmd->chanlist_len > 0)) {
/* Peek analogue reference of first channel. */
if (CR_AREF(cmd->chanlist[0]) == AREF_DIFF)
@@ -1735,8 +1821,10 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
~CR_FLAGS_MASK);
err |= -EINVAL;
}
- /* The only flags allowed are CR_INVERT and CR_EDGE.
- * CR_EDGE is required. */
+ /*
+ * The only flags allowed are CR_INVERT and CR_EDGE.
+ * CR_EDGE is required.
+ */
if ((cmd->convert_arg & (CR_FLAGS_MASK & ~CR_INVERT))
!= CR_EDGE) {
/* Set CR_EDGE, preserve CR_INVERT. */
@@ -1747,9 +1835,11 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
err |= -EINVAL;
}
} else {
- /* Backwards compatibility with previous versions. */
- /* convert_arg == 0 => trigger on -ve edge. */
- /* convert_arg == 1 => trigger on +ve edge. */
+ /*
+ * Backwards compatibility with previous versions:
+ * convert_arg == 0 => trigger on -ve edge.
+ * convert_arg == 1 => trigger on +ve edge.
+ */
err |= cfc_check_trigger_arg_max(&cmd->convert_arg, 1);
}
} else {
@@ -1762,9 +1852,11 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_arg_is(&cmd->stop_arg, 0);
if (cmd->scan_begin_src == TRIG_EXT) {
- /* external "trigger" to begin each scan
+ /*
+ * external "trigger" to begin each scan:
* scan_begin_arg==0 => use PPC0 input -> gate of CT0 -> gate
- * of CT2 (sample convert trigger is CT2) */
+ * of CT2 (sample convert trigger is CT2)
+ */
if ((cmd->scan_begin_arg & ~CR_FLAGS_MASK) != 0) {
cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
~CR_FLAGS_MASK);
@@ -1788,9 +1880,7 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
if (err)
return 3;
- /* Step 4: fix up any arguments.
- * "argument conflict" returned by comedilib to user mode process
- * if this fails. */
+ /* Step 4: fix up any arguments */
if (cmd->convert_src == TRIG_TIMER) {
tmp = cmd->convert_arg;
@@ -1884,17 +1974,21 @@ static int pci230_ai_inttrig_convert(struct comedi_device *dev,
if (test_bit(AI_CMD_STARTED, &devpriv->state)) {
unsigned int delayus;
- /* Trigger conversion by toggling Z2-CT2 output. Finish
- * with output high. */
+ /*
+ * Trigger conversion by toggling Z2-CT2 output.
+ * Finish with output high.
+ */
i8254_set_mode(devpriv->iobase1 + PCI230_Z2_CT_BASE, 0, 2,
I8254_MODE0);
i8254_set_mode(devpriv->iobase1 + PCI230_Z2_CT_BASE, 0, 2,
I8254_MODE1);
- /* Delay. Should driver be responsible for this? An
+ /*
+ * Delay. Should driver be responsible for this? An
* alternative would be to wait until conversion is complete,
* but we can't tell when it's complete because the ADC busy
* bit has a different meaning when FIFO enabled (and when
- * FIFO not enabled, it only works for software triggers). */
+ * FIFO not enabled, it only works for software triggers).
+ */
if (((devpriv->adccon & PCI230_ADC_IM_MASK)
== PCI230_ADC_IM_DIF)
&& (devpriv->hwver == 0)) {
@@ -1960,8 +2054,10 @@ static void pci230_ai_stop(struct comedi_device *dev,
pci230_cancel_ct(dev, 0);
}
spin_lock_irqsave(&devpriv->isr_spinlock, irqflags);
- /* Disable ADC interrupt and wait for interrupt routine to finish
- * running unless we are called from the interrupt routine. */
+ /*
+ * Disable ADC interrupt and wait for interrupt routine to finish
+ * running unless we are called from the interrupt routine.
+ */
devpriv->int_en &= ~PCI230_INT_ADC;
while (devpriv->intr_running && devpriv->intr_cpuid != THISCPU) {
spin_unlock_irqrestore(&devpriv->isr_spinlock, irqflags);
@@ -1972,8 +2068,10 @@ static void pci230_ai_stop(struct comedi_device *dev,
outb(devpriv->ier, devpriv->iobase1 + PCI230_INT_SCE);
}
spin_unlock_irqrestore(&devpriv->isr_spinlock, irqflags);
- /* Reset FIFO, disable FIFO and set start conversion source to none.
- * Keep se/diff and bip/uni settings */
+ /*
+ * Reset FIFO, disable FIFO and set start conversion source to none.
+ * Keep se/diff and bip/uni settings.
+ */
devpriv->adccon = (devpriv->adccon & (PCI230_ADC_IR_MASK
| PCI230_ADC_IM_MASK)) |
PCI230_ADC_TRIG_NONE;
@@ -2006,8 +2104,10 @@ static void pci230_ai_start(struct comedi_device *dev,
outb(devpriv->ier, devpriv->iobase1 + PCI230_INT_SCE);
spin_unlock_irqrestore(&devpriv->isr_spinlock, irqflags);
- /* Update conversion trigger source which is currently set
- * to CT2 output, which is currently stuck high. */
+ /*
+ * Update conversion trigger source which is currently set
+ * to CT2 output, which is currently stuck high.
+ */
switch (cmd->convert_src) {
default:
conv = PCI230_ADC_TRIG_NONE;
@@ -2037,8 +2137,10 @@ static void pci230_ai_start(struct comedi_device *dev,
}
break;
case TRIG_INT:
- /* Use CT2 output for software trigger due to problems
- * in differential mode on PCI230/260. */
+ /*
+ * Use CT2 output for software trigger due to problems
+ * in differential mode on PCI230/260.
+ */
conv = PCI230_ADC_TRIG_Z2CT2;
break;
}
@@ -2048,20 +2150,26 @@ static void pci230_ai_start(struct comedi_device *dev,
if (cmd->convert_src == TRIG_INT)
async->inttrig = pci230_ai_inttrig_convert;
- /* Update FIFO interrupt trigger level, which is currently
- * set to "full". */
+ /*
+ * Update FIFO interrupt trigger level, which is currently
+ * set to "full".
+ */
pci230_ai_update_fifo_trigger_level(dev, s);
if (cmd->convert_src == TRIG_TIMER) {
/* Update timer gates. */
unsigned char zgat;
if (cmd->scan_begin_src != TRIG_FOLLOW) {
- /* Conversion timer CT2 needs to be gated by
- * inverted output of monostable CT2. */
+ /*
+ * Conversion timer CT2 needs to be gated by
+ * inverted output of monostable CT2.
+ */
zgat = GAT_CONFIG(2, GAT_NOUTNM2);
} else {
- /* Conversion timer CT2 needs to be gated on
- * continuously. */
+ /*
+ * Conversion timer CT2 needs to be gated on
+ * continuously.
+ */
zgat = GAT_CONFIG(2, GAT_VCC);
}
outb(zgat, devpriv->iobase1 + PCI230_ZGAT_SCE);
@@ -2103,8 +2211,10 @@ static void pci230_ai_start(struct comedi_device *dev,
outb(zgat, devpriv->iobase1 + PCI230_ZGAT_SCE);
switch (cmd->scan_begin_src) {
case TRIG_TIMER:
- /* Scan period timer CT1 needs to be
- * gated on to start counting. */
+ /*
+ * Scan period timer CT1 needs to be
+ * gated on to start counting.
+ */
zgat = GAT_CONFIG(1, GAT_VCC);
outb(zgat, devpriv->iobase1
+ PCI230_ZGAT_SCE);
@@ -2172,8 +2282,10 @@ static void pci230_handle_ai(struct comedi_device *dev,
/* Read FIFO state. */
status_fifo = inw(dev->iobase + PCI230_ADCCON);
if ((status_fifo & PCI230_ADC_FIFO_FULL_LATCHED) != 0) {
- /* Report error otherwise FIFO overruns will go
- * unnoticed by the caller. */
+ /*
+ * Report error otherwise FIFO overruns will go
+ * unnoticed by the caller.
+ */
dev_err(dev->class_dev, "AI FIFO overrun\n");
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
break;
@@ -2247,8 +2359,10 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
* Determine which shared resources are needed.
*/
res_mask = 0;
- /* Need Z2-CT2 to supply a conversion trigger source at a high
- * logic level, even if not doing timed conversions. */
+ /*
+ * Need Z2-CT2 to supply a conversion trigger source at a high
+ * logic level, even if not doing timed conversions.
+ */
res_mask |= (1U << RES_Z2CT2);
if (cmd->scan_begin_src != TRIG_FOLLOW) {
/* Using Z2-CT0 monostable to gate Z2-CT2 conversion timer */
@@ -2270,7 +2384,8 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
devpriv->ai_scan_count = 0;
devpriv->ai_scan_pos = 0; /* Position within scan. */
- /* Steps;
+ /*
+ * Steps:
* - Set channel scan list.
* - Set channel gains.
* - Enable and reset FIFO, specify uni/bip, se/diff, and set
@@ -2315,12 +2430,16 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
if (diff) {
gainshift = 2 * chan;
if (devpriv->hwver == 0) {
- /* Original PCI230/260 expects both inputs of
- * the differential channel to be enabled. */
+ /*
+ * Original PCI230/260 expects both inputs of
+ * the differential channel to be enabled.
+ */
adcen |= 3 << gainshift;
} else {
- /* PCI230+/260+ expects only one input of the
- * differential channel to be enabled. */
+ /*
+ * PCI230+/260+ expects only one input of the
+ * differential channel to be enabled.
+ */
adcen |= 1 << gainshift;
}
} else {
@@ -2337,38 +2456,48 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
/* Set channel gains. */
outw(devpriv->adcg, dev->iobase + PCI230_ADCG);
- /* Set counter/timer 2 output high for use as the initial start
- * conversion source. */
+ /*
+ * Set counter/timer 2 output high for use as the initial start
+ * conversion source.
+ */
i8254_set_mode(devpriv->iobase1 + PCI230_Z2_CT_BASE, 0, 2, I8254_MODE1);
- /* Temporarily use CT2 output as conversion trigger source and
- * temporarily set FIFO interrupt trigger level to 'full'. */
+ /*
+ * Temporarily use CT2 output as conversion trigger source and
+ * temporarily set FIFO interrupt trigger level to 'full'.
+ */
adccon |= PCI230_ADC_INT_FIFO_FULL | PCI230_ADC_TRIG_Z2CT2;
- /* Enable and reset FIFO, specify FIFO trigger level full, specify
+ /*
+ * Enable and reset FIFO, specify FIFO trigger level full, specify
* uni/bip, se/diff, and temporarily set the start conversion source
* to CT2 output. Note that CT2 output is currently high, and this
* will produce a false conversion trigger on some versions of the
- * PCI230/260, but that will be dealt with later. */
+ * PCI230/260, but that will be dealt with later.
+ */
devpriv->adccon = adccon;
outw(adccon | PCI230_ADC_FIFO_RESET, dev->iobase + PCI230_ADCCON);
- /* Delay */
- /* Failure to include this will result in the first few channels'-worth
+ /*
+ * Delay -
+ * Failure to include this will result in the first few channels'-worth
* of data being corrupt, normally manifesting itself by large negative
* voltages. It seems the board needs time to settle between the first
* FIFO reset (above) and the second FIFO reset (below). Setting the
* channel gains and scan list _before_ the first FIFO reset also
- * helps, though only slightly. */
+ * helps, though only slightly.
+ */
udelay(25);
/* Reset FIFO again. */
outw(adccon | PCI230_ADC_FIFO_RESET, dev->iobase + PCI230_ADCCON);
if (cmd->convert_src == TRIG_TIMER) {
- /* Set up CT2 as conversion timer, but gate it off for now.
+ /*
+ * Set up CT2 as conversion timer, but gate it off for now.
* Note, counter/timer output 2 can be monitored on the
- * connector: PCI230 pin 21, PCI260 pin 18. */
+ * connector: PCI230 pin 21, PCI260 pin 18.
+ */
zgat = GAT_CONFIG(2, GAT_GND);
outb(zgat, devpriv->iobase1 + PCI230_ZGAT_SCE);
/* Set counter/timer 2 to the specified conversion period. */
@@ -2442,9 +2571,11 @@ static irqreturn_t pci230_interrupt(int irq, void *d)
spin_lock_irqsave(&devpriv->isr_spinlock, irqflags);
valid_status_int = devpriv->int_en & status_int;
- /* Disable triggered interrupts.
+ /*
+ * Disable triggered interrupts.
* (Only those interrupts that need re-enabling, are, later in the
- * handler). */
+ * handler).
+ */
devpriv->ier = devpriv->int_en & ~status_int;
outb(devpriv->ier, devpriv->iobase1 + PCI230_INT_SCE);
devpriv->intr_running = 1;
@@ -2501,8 +2632,10 @@ static bool pci230_match_pci_board(const struct pci230_board *board,
/* Looking for a '+' model. First check length of registers. */
if (pci_resource_len(pci_dev, 3) < 32)
return false; /* Not a '+' model. */
- /* TODO: temporarily enable PCI device and read the hardware version
- * register. For now, assume it's okay. */
+ /*
+ * TODO: temporarily enable PCI device and read the hardware version
+ * register. For now, assume it's okay.
+ */
return true;
}
@@ -2591,8 +2724,10 @@ static int pci230_attach_common(struct comedi_device *dev,
if (rc)
return rc;
- /* Read base addresses of the PCI230's two I/O regions from PCI
- * configuration register. */
+ /*
+ * Read base addresses of the PCI230's two I/O regions from PCI
+ * configuration register.
+ */
iobase1 = pci_resource_start(pci_dev, 2);
iobase2 = pci_resource_start(pci_dev, 3);
dev_dbg(dev->class_dev,
@@ -2602,8 +2737,10 @@ static int pci230_attach_common(struct comedi_device *dev,
dev->iobase = iobase2;
/* Read bits of DACCON register - only the output range. */
devpriv->daccon = inw(dev->iobase + PCI230_DACCON) & PCI230_DAC_OR_MASK;
- /* Read hardware version register and set extended function register
- * if they exist. */
+ /*
+ * Read hardware version register and set extended function register
+ * if they exist.
+ */
if (pci_resource_len(pci_dev, 3) >= 32) {
unsigned short extfunc = 0;
@@ -2617,11 +2754,13 @@ static int pci230_attach_common(struct comedi_device *dev,
}
if (devpriv->hwver > 0) {
if (!thisboard->have_dio) {
- /* No DIO ports. Route counters' external gates
+ /*
+ * No DIO ports. Route counters' external gates
* to the EXTTRIG signal (PCI260+ pin 17).
* (Otherwise, they would be routed to DIO
* inputs PC0, PC1 and PC2 which don't exist
- * on PCI260[+].) */
+ * on PCI260[+].)
+ */
extfunc |= PCI230P_EXTFUNC_GAT_EXTTRIG;
}
if ((thisboard->ao_chans > 0)
@@ -2632,8 +2771,10 @@ static int pci230_attach_common(struct comedi_device *dev,
}
outw(extfunc, dev->iobase + PCI230P_EXTFUNC);
if ((extfunc & PCI230P2_EXTFUNC_DACFIFO) != 0) {
- /* Temporarily enable DAC FIFO, reset it and disable
- * FIFO wraparound. */
+ /*
+ * Temporarily enable DAC FIFO, reset it and disable
+ * FIFO wraparound.
+ */
outw(devpriv->daccon | PCI230P2_DAC_FIFO_EN
| PCI230P2_DAC_FIFO_RESET,
dev->iobase + PCI230_DACCON);
--
2.0.0
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index cb86d04..c6c3c4a 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -664,10 +664,8 @@ static inline void pci230_ao_write_nofifo(struct comedi_device *dev,
devpriv->ao_readback[chan] = datum;
/* Write mangled datum to appropriate DACOUT register. */
- outw(pci230_ao_mangle_datum(dev, datum), dev->iobase + (((chan) == 0)
- ? PCI230_DACOUT1
- :
- PCI230_DACOUT2));
+ outw(pci230_ao_mangle_datum(dev, datum),
+ dev->iobase + (((chan) == 0) ? PCI230_DACOUT1 : PCI230_DACOUT2));
}
static inline void pci230_ao_write_fifo(struct comedi_device *dev,
--
2.0.0
Fix checkpatch issue: "CHECK: usleep_range is preferred over udelay; see
Documentation/timers/timers-howto.txt". I picked 100 us as a reasonable
upper bound, but it's not that critical.
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 76c4625..00d7a22 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -2480,7 +2480,7 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
* channel gains and scan list _before_ the first FIFO reset also
* helps, though only slightly.
*/
- udelay(25);
+ usleep_range(25, 100);
/* Reset FIFO again. */
outw(adccon | PCI230_ADC_FIFO_RESET, dev->iobase + PCI230_ADCCON);
--
2.0.0
Fix checkpatch issues: "CHECK: Blank lines aren't necessary before a
close brace '}'".
Signed-off-by: Ian Abbott <[email protected]>
---
drivers/staging/comedi/drivers/amplc_pci230.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 0609e51..51f28b6 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -739,7 +739,6 @@ static void put_resources(struct comedi_device *dev, unsigned int res_mask,
res_mask &= ~b;
if (devpriv->res_owner[i] == owner)
devpriv->res_owner[i] = OWNER_NONE;
-
}
}
spin_unlock_irqrestore(&devpriv->res_spinlock, irqflags);
@@ -792,7 +791,6 @@ static unsigned int pci230_choose_clk_count(uint64_t ns, unsigned int *count,
cnt = divide_ns(ns, pci230_timebase[clk_src], flags);
if ((cnt <= 65536) || (clk_src == CLK_1KHZ))
break;
-
}
*count = cnt;
return clk_src;
@@ -1448,7 +1446,6 @@ static void pci230_ao_start(struct comedi_device *dev,
& ~PCI230P2_DAC_TRIG_MASK) |
scantrig;
outw(devpriv->daccon, dev->iobase + PCI230_DACCON);
-
}
switch (cmd->scan_begin_src) {
case TRIG_TIMER:
@@ -1512,7 +1509,6 @@ static int pci230_ao_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
/* Claim Z2-CT1. */
if (!get_one_resource(dev, RES_Z2CT1, OWNER_AOCMD))
return -EBUSY;
-
}
/* Get number of scans required. */
--
2.0.0
On Tuesday, July 29, 2014 4:58 AM, Ian Abbott wrote:
> Signed-off-by: Ian Abbott <[email protected]>
> ---
> drivers/staging/comedi/drivers/amplc_pci230.c | 151 ++++++++++----------------
> 1 file changed, 58 insertions(+), 93 deletions(-)
>
> diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
> index 4222e28..df58679 100644
> --- a/drivers/staging/comedi/drivers/amplc_pci230.c
> +++ b/drivers/staging/comedi/drivers/amplc_pci230.c
> @@ -672,7 +672,7 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
> ok = 1;
> claimed = 0;
> spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
> - for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++) {
> + for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++)
> if (res_mask & b) {
> res_mask &= ~b;
> if (devpriv->res_owner[i] == OWNER_NONE) {
> @@ -690,7 +690,6 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
> break;
> }
> }
> - }
Technically the braces you remove in this patch _are_
unnecessary. But, I think the driver is more confusing
with them removed.
In a lot of places there is quite a bit of code between
where the opening and closing braces would be.
Granted, a lot of them are due to the wordy comments
but some are in places like:
for (...)
if (...) {
...
}
There aren't too bad but the one like this are:
If (...)
If (...)
...
else
...
else
...
The nested if/else blocks are easy to break.
Just my two cents...
Hartley
On Tuesday, July 29, 2014 4:58 AM, Ian Abbott wrote:
>
> Tidy up the "amplc_pci230" driver a bit. There are more changes to come
> after this. The only one of these that should alter the object code is
> patch 06, which replaces a udelay() call with usleep_range().
>
> 01) staging: comedi: amplc_pci230: reformat a load of comments
> 02) staging: comedi: amplc_pci230: fix checkpatch line over 80
> characters
> 03) staging: comedi: amplc_pci230: logical continuations should be on
> the previous line
> 04) staging: comedi: amplc_pci230: blank lines aren't necessary before a
> close brace '}'
> 05) staging: comedi: amplc_pci230: alignment should match open
> parenthesis
> 06) staging: comedi: amplc_pci230: usleep_range is preferred over udelay
> 07) staging: comedi: amplc_pci230: remove unused settling time constants
> 08) staging: comedi: amplc_pci230: remove PCI230_ADC_CONV
> 09) staging: comedi: amplc_pci230: remove PCI230_TEST_BIT()
> 10) staging: comedi: amplc_pci230: add whitespace to register values
> 11) staging: comedi: amplc_pci230: don't begin line with binary operator
> 12) staging: comedi: amplc_pci230: omit '!= 0' from logical expressions
> 13) staging: comedi: amplc_pci230: remove unnecessary braces
> 14) staging: comedi: amplc_pci230: remove some indentation in
> pci230_ai_check_chanlist()
> 15) staging: comedi: amplc_pci230: no need for '&function'
> 16) staging: comedi: amplc_pci230: add whitespace to pci230_boards[]
> 17) staging: comedi: amplc_pci230: no need to initialize named members
> to zero
> 18) staging: comedi: amplc_pci230: tidy up stuct pci230_private
> 19) staging: comedi: amplc_pci230: remove some unnecessary parentheses
>
> drivers/staging/comedi/drivers/amplc_pci230.c | 1417 +++++++++++++------------
> 1 file changed, 736 insertions(+), 681 deletions(-)
Other than my comment about patch 13, this looks ok.
Reviewed-by: H Hartley Sweeten <[email protected]>
Signed-off-by: Ian Abbott <[email protected]>
---
v2: Be less aggressive in brace removal. Keep them for outer nested
'if's. Keep them in outer control statements where the inner control
statement uses braces.
---
drivers/staging/comedi/drivers/amplc_pci230.c | 120 ++++++++++----------------
1 file changed, 46 insertions(+), 74 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 4222e28..dfc8798 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -862,19 +862,18 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
if (aref == AREF_DIFF) {
/* Differential. */
gainshift = chan * 2;
- if (devpriv->hwver == 0) {
+ if (devpriv->hwver == 0)
/*
* Original PCI230/260 expects both inputs of the
* differential channel to be enabled.
*/
adcen = 3 << gainshift;
- } else {
+ else
/*
* PCI230+/260+ expects only one input of the
* differential channel to be enabled.
*/
adcen = 1 << gainshift;
- }
adccon |= PCI230_ADC_IM_DIF;
} else {
/* Single ended. */
@@ -889,7 +888,6 @@ static int pci230_ai_rinsn(struct comedi_device *dev,
else
adccon |= PCI230_ADC_IR_UNI;
-
/*
* Enable only this channel in the scan list - otherwise by default
* we'll get one sample from each channel.
@@ -953,10 +951,9 @@ static int pci230_ao_winsn(struct comedi_device *dev,
* Writing a list of values to an AO channel is probably not
* very useful, but that's how the interface is defined.
*/
- for (i = 0; i < insn->n; i++) {
+ for (i = 0; i < insn->n; i++)
/* Write value to DAC and store it. */
pci230_ao_write_nofifo(dev, data[i], chan);
- }
/* return the number of samples read/written */
return i;
@@ -1025,7 +1022,7 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_src(&cmd->start_src, TRIG_INT);
tmp = TRIG_TIMER | TRIG_INT;
- if ((thisboard->min_hwver > 0) && (devpriv->hwver >= 2)) {
+ if ((thisboard->min_hwver > 0) && (devpriv->hwver >= 2))
/*
* For PCI230+ hardware version 2 onwards, allow external
* trigger from EXTTRIG/EXTCONVCLK input (PCI230+ pin 25).
@@ -1041,7 +1038,6 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
* guarantee!
*/
tmp |= TRIG_EXT;
- }
err |= cfc_check_trigger_src(&cmd->scan_begin_src, tmp);
err |= cfc_check_trigger_src(&cmd->convert_src, TRIG_NOW);
@@ -1151,18 +1147,16 @@ static void pci230_ao_stop(struct comedi_device *dev,
if (!started)
return;
cmd = &s->async->cmd;
- if (cmd->scan_begin_src == TRIG_TIMER) {
+ if (cmd->scan_begin_src == TRIG_TIMER)
/* Stop scan rate generator. */
pci230_cancel_ct(dev, 1);
- }
/* Determine interrupt source. */
- if (devpriv->hwver < 2) {
+ if (devpriv->hwver < 2)
/* Not using DAC FIFO. Using CT1 interrupt. */
intsrc = PCI230_INT_ZCLK_CT1;
- } else {
+ else
/* Using DAC FIFO interrupt. */
intsrc = PCI230P2_INT_DAC;
- }
/*
* Disable interrupt and wait for interrupt routine to finish running
* unless we are called from the interrupt routine.
@@ -1249,10 +1243,9 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
/* Fixed number of scans. */
if (num_scans > devpriv->ao_scan_count)
num_scans = devpriv->ao_scan_count;
- if (devpriv->ao_scan_count == 0) {
+ if (devpriv->ao_scan_count == 0)
/* End of acquisition. */
events |= COMEDI_CB_EOA;
- }
}
if (events == 0) {
/* Check for FIFO underrun. */
@@ -1390,10 +1383,9 @@ static void pci230_ao_start(struct comedi_device *dev,
/* Preload FIFO data. */
run = pci230_handle_ao_fifo(dev, s);
comedi_event(dev, s);
- if (!run) {
+ if (!run)
/* Stopped. */
return;
- }
/* Set scan trigger source. */
switch (cmd->scan_begin_src) {
case TRIG_TIMER:
@@ -1401,13 +1393,12 @@ static void pci230_ao_start(struct comedi_device *dev,
break;
case TRIG_EXT:
/* Trigger on EXTTRIG/EXTCONVCLK pin. */
- if ((cmd->scan_begin_arg & CR_INVERT) == 0) {
+ if ((cmd->scan_begin_arg & CR_INVERT) == 0)
/* +ve edge */
scantrig = PCI230P2_DAC_TRIG_EXTP;
- } else {
+ else
/* -ve edge */
scantrig = PCI230P2_DAC_TRIG_EXTN;
- }
break;
case TRIG_INT:
scantrig = PCI230P2_DAC_TRIG_SW;
@@ -1695,7 +1686,7 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_src(&cmd->start_src, TRIG_NOW | TRIG_INT);
tmp = TRIG_FOLLOW | TRIG_TIMER | TRIG_INT;
- if ((thisboard->have_dio) || (thisboard->min_hwver > 0)) {
+ if ((thisboard->have_dio) || (thisboard->min_hwver > 0))
/*
* Unfortunately, we cannot trigger a scan off an external
* source on the PCI260 board, since it uses the PPIC0 (DIO)
@@ -1703,7 +1694,6 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* we can use the EXTTRIG/EXTCONVCLK input on pin 17 instead.
*/
tmp |= TRIG_EXT;
- }
err |= cfc_check_trigger_src(&cmd->scan_begin_src, tmp);
err |= cfc_check_trigger_src(&cmd->convert_src,
TRIG_TIMER | TRIG_INT | TRIG_EXT);
@@ -1760,7 +1750,6 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
max_speed_ai = MAX_SPEED_AI_DIFF;
else
max_speed_ai = MAX_SPEED_AI_SE;
-
} else {
/* No channel list. Assume single-ended. */
max_speed_ai = MAX_SPEED_AI_SE;
@@ -1895,32 +1884,27 @@ static void pci230_ai_update_fifo_trigger_level(struct comedi_device *dev,
unsigned short triglev;
unsigned short adccon;
- if (cmd->flags & TRIG_WAKE_EOS) {
+ if (cmd->flags & TRIG_WAKE_EOS)
/* Wake at end of scan. */
wake = scanlen - devpriv->ai_scan_pos;
- } else {
- if (cmd->stop_src != TRIG_COUNT ||
- devpriv->ai_scan_count >= PCI230_ADC_FIFOLEVEL_HALFFULL ||
- scanlen >= PCI230_ADC_FIFOLEVEL_HALFFULL) {
- wake = PCI230_ADC_FIFOLEVEL_HALFFULL;
- } else {
- wake = (devpriv->ai_scan_count * scanlen) -
- devpriv->ai_scan_pos;
- }
- }
+ else if (cmd->stop_src != TRIG_COUNT ||
+ devpriv->ai_scan_count >= PCI230_ADC_FIFOLEVEL_HALFFULL ||
+ scanlen >= PCI230_ADC_FIFOLEVEL_HALFFULL)
+ wake = PCI230_ADC_FIFOLEVEL_HALFFULL;
+ else
+ wake = (devpriv->ai_scan_count * scanlen) -
+ devpriv->ai_scan_pos;
if (wake >= PCI230_ADC_FIFOLEVEL_HALFFULL) {
triglev = PCI230_ADC_INT_FIFO_HALF;
- } else {
- if ((wake > 1) && (devpriv->hwver > 0)) {
- /* PCI230+/260+ programmable FIFO interrupt level. */
- if (devpriv->adcfifothresh != wake) {
- devpriv->adcfifothresh = wake;
- outw(wake, dev->iobase + PCI230P_ADCFFTH);
- }
- triglev = PCI230P_ADC_INT_FIFO_THRESH;
- } else {
- triglev = PCI230_ADC_INT_FIFO_NEMPTY;
+ } else if ((wake > 1) && (devpriv->hwver > 0)) {
+ /* PCI230+/260+ programmable FIFO interrupt level. */
+ if (devpriv->adcfifothresh != wake) {
+ devpriv->adcfifothresh = wake;
+ outw(wake, dev->iobase + PCI230P_ADCFFTH);
}
+ triglev = PCI230P_ADC_INT_FIFO_THRESH;
+ } else {
+ triglev = PCI230_ADC_INT_FIFO_NEMPTY;
}
adccon = (devpriv->adccon & ~PCI230_ADC_INT_FIFO_MASK) | triglev;
if (adccon != devpriv->adccon) {
@@ -2013,14 +1997,12 @@ static void pci230_ai_stop(struct comedi_device *dev,
if (!started)
return;
cmd = &s->async->cmd;
- if (cmd->convert_src == TRIG_TIMER) {
+ if (cmd->convert_src == TRIG_TIMER)
/* Stop conversion rate generator. */
pci230_cancel_ct(dev, 2);
- }
- if (cmd->scan_begin_src != TRIG_FOLLOW) {
+ if (cmd->scan_begin_src != TRIG_FOLLOW)
/* Stop scan period monostable. */
pci230_cancel_ct(dev, 0);
- }
spin_lock_irqsave(&devpriv->isr_spinlock, irqflags);
/*
* Disable ADC interrupt and wait for interrupt routine to finish
@@ -2086,22 +2068,20 @@ static void pci230_ai_start(struct comedi_device *dev,
break;
case TRIG_EXT:
if (cmd->convert_arg & CR_EDGE) {
- if ((cmd->convert_arg & CR_INVERT) == 0) {
+ if ((cmd->convert_arg & CR_INVERT) == 0)
/* Trigger on +ve edge. */
conv = PCI230_ADC_TRIG_EXTP;
- } else {
+ else
/* Trigger on -ve edge. */
conv = PCI230_ADC_TRIG_EXTN;
- }
} else {
/* Backwards compatibility. */
- if (cmd->convert_arg) {
+ if (cmd->convert_arg)
/* Trigger on +ve edge. */
conv = PCI230_ADC_TRIG_EXTP;
- } else {
+ else
/* Trigger on -ve edge. */
conv = PCI230_ADC_TRIG_EXTN;
- }
}
break;
case TRIG_INT:
@@ -2127,19 +2107,18 @@ static void pci230_ai_start(struct comedi_device *dev,
/* Update timer gates. */
unsigned char zgat;
- if (cmd->scan_begin_src != TRIG_FOLLOW) {
+ if (cmd->scan_begin_src != TRIG_FOLLOW)
/*
* Conversion timer CT2 needs to be gated by
* inverted output of monostable CT2.
*/
zgat = GAT_CONFIG(2, GAT_NOUTNM2);
- } else {
+ else
/*
* Conversion timer CT2 needs to be gated on
* continuously.
*/
zgat = GAT_CONFIG(2, GAT_VCC);
- }
outb(zgat, devpriv->iobase1 + PCI230_ZGAT_SCE);
if (cmd->scan_begin_src != TRIG_FOLLOW) {
/* Set monostable CT0 trigger source. */
@@ -2269,10 +2248,9 @@ static void pci230_handle_ai(struct comedi_device *dev,
/* Read PCI230+/260+ ADC FIFO level. */
fifoamount =
inw(dev->iobase + PCI230P_ADCFFLEV);
- if (fifoamount == 0) {
+ if (fifoamount == 0)
/* Shouldn't happen. */
break;
- }
} else {
fifoamount = 1;
}
@@ -2293,22 +2271,20 @@ static void pci230_handle_ai(struct comedi_device *dev,
async->events |= COMEDI_CB_EOS;
}
}
- if (cmd->stop_src == TRIG_COUNT && devpriv->ai_scan_count == 0) {
+ if (cmd->stop_src == TRIG_COUNT && devpriv->ai_scan_count == 0)
/* End of acquisition. */
events |= COMEDI_CB_EOA;
- } else {
+ else
/* More samples required, tell Comedi to block. */
events |= COMEDI_CB_BLOCK;
- }
async->events |= events;
if (async->events & (COMEDI_CB_EOA | COMEDI_CB_ERROR |
- COMEDI_CB_OVERFLOW)) {
+ COMEDI_CB_OVERFLOW))
/* disable hardware conversions */
pci230_ai_stop(dev, s);
- } else {
+ else
/* update FIFO interrupt trigger level */
pci230_ai_update_fifo_trigger_level(dev, s);
- }
}
static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
@@ -2335,10 +2311,9 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
if (cmd->scan_begin_src != TRIG_FOLLOW) {
/* Using Z2-CT0 monostable to gate Z2-CT2 conversion timer */
res_mask |= (1U << RES_Z2CT0);
- if (cmd->scan_begin_src == TRIG_TIMER) {
+ if (cmd->scan_begin_src == TRIG_TIMER)
/* Using Z2-CT1 for scan frequency */
res_mask |= (1U << RES_Z2CT1);
- }
}
/* Claim resources. */
if (!get_resources(dev, res_mask, OWNER_AICMD))
@@ -2397,19 +2372,18 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
range = CR_RANGE(cmd->chanlist[i]);
if (diff) {
gainshift = 2 * chan;
- if (devpriv->hwver == 0) {
+ if (devpriv->hwver == 0)
/*
* Original PCI230/260 expects both inputs of
* the differential channel to be enabled.
*/
adcen |= 3 << gainshift;
- } else {
+ else
/*
* PCI230+/260+ expects only one input of the
* differential channel to be enabled.
*/
adcen |= 1 << gainshift;
- }
} else {
gainshift = (chan & ~1);
adcen |= 1 << chan;
@@ -2721,7 +2695,7 @@ static int pci230_attach_common(struct comedi_device *dev,
return -EIO;
}
if (devpriv->hwver > 0) {
- if (!thisboard->have_dio) {
+ if (!thisboard->have_dio)
/*
* No DIO ports. Route counters' external gates
* to the EXTTRIG signal (PCI260+ pin 17).
@@ -2730,12 +2704,10 @@ static int pci230_attach_common(struct comedi_device *dev,
* on PCI260[+].)
*/
extfunc |= PCI230P_EXTFUNC_GAT_EXTTRIG;
- }
if ((thisboard->ao_chans > 0) &&
- (devpriv->hwver >= 2)) {
+ (devpriv->hwver >= 2))
/* Enable DAC FIFO functionality. */
extfunc |= PCI230P2_EXTFUNC_DACFIFO;
- }
}
outw(extfunc, dev->iobase + PCI230P_EXTFUNC);
if (extfunc & PCI230P2_EXTFUNC_DACFIFO) {
--
2.0.0
Remove some pairs of parentheses that don't really improve readability.
Also, reduce the amount of leading whitespace in a few places.
Signed-off-by: Ian Abbott <[email protected]>
---
v2: fixed conflict with v2 on an earlier patch in the series.
---
drivers/staging/comedi/drivers/amplc_pci230.c | 78 +++++++++++++--------------
1 file changed, 37 insertions(+), 41 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 589a4ee..8abadd9 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -628,7 +628,7 @@ static inline void pci230_ao_write_nofifo(struct comedi_device *dev,
/* Write mangled datum to appropriate DACOUT register. */
outw(pci230_ao_mangle_datum(dev, datum),
- dev->iobase + (((chan) == 0) ? PCI230_DACOUT1 : PCI230_DACOUT2));
+ dev->iobase + (chan == 0 ? PCI230_DACOUT1 : PCI230_DACOUT2));
}
static inline void pci230_ao_write_fifo(struct comedi_device *dev,
@@ -657,7 +657,7 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
ok = 1;
claimed = 0;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++) {
+ for (b = 1, i = 0; i < NUM_RESOURCES && res_mask; b <<= 1, i++) {
if (res_mask & b) {
res_mask &= ~b;
if (devpriv->res_owner[i] == OWNER_NONE) {
@@ -683,7 +683,7 @@ static int get_resources(struct comedi_device *dev, unsigned int res_mask,
static inline int get_one_resource(struct comedi_device *dev,
unsigned int resource, unsigned char owner)
{
- return get_resources(dev, (1U << resource), owner);
+ return get_resources(dev, 1U << resource, owner);
}
static void put_resources(struct comedi_device *dev, unsigned int res_mask,
@@ -695,7 +695,7 @@ static void put_resources(struct comedi_device *dev, unsigned int res_mask,
unsigned long irqflags;
spin_lock_irqsave(&devpriv->res_spinlock, irqflags);
- for (b = 1, i = 0; (i < NUM_RESOURCES) && res_mask; b <<= 1, i++) {
+ for (b = 1, i = 0; i < NUM_RESOURCES && res_mask; b <<= 1, i++) {
if (res_mask & b) {
res_mask &= ~b;
if (devpriv->res_owner[i] == owner)
@@ -708,7 +708,7 @@ static void put_resources(struct comedi_device *dev, unsigned int res_mask,
static inline void put_one_resource(struct comedi_device *dev,
unsigned int resource, unsigned char owner)
{
- put_resources(dev, (1U << resource), owner);
+ put_resources(dev, 1U << resource, owner);
}
static inline void put_all_resources(struct comedi_device *dev,
@@ -750,7 +750,7 @@ static unsigned int pci230_choose_clk_count(uint64_t ns, unsigned int *count,
for (clk_src = CLK_10MHZ;; clk_src++) {
cnt = divide_ns(ns, pci230_timebase[clk_src], flags);
- if ((cnt <= 65536) || (clk_src == CLK_1KHZ))
+ if (cnt <= 65536 || clk_src == CLK_1KHZ)
break;
}
*count = cnt;
@@ -1007,7 +1007,7 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_src(&cmd->start_src, TRIG_INT);
tmp = TRIG_TIMER | TRIG_INT;
- if ((thisboard->min_hwver > 0) && (devpriv->hwver >= 2))
+ if (thisboard->min_hwver > 0 && devpriv->hwver >= 2)
/*
* For PCI230+ hardware version 2 onwards, allow external
* trigger from EXTTRIG/EXTCONVCLK input (PCI230+ pin 25).
@@ -1074,11 +1074,11 @@ static int pci230_ao_cmdtest(struct comedi_device *dev,
* The only flags allowed are CR_EDGE and CR_INVERT.
* The CR_EDGE flag is ignored.
*/
- if (cmd->scan_begin_arg &
- (CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT))) {
- cmd->scan_begin_arg = COMBINE(cmd->scan_begin_arg, 0,
- CR_FLAGS_MASK &
- ~(CR_EDGE | CR_INVERT));
+ if (cmd->scan_begin_arg & CR_FLAGS_MASK &
+ ~(CR_EDGE | CR_INVERT)) {
+ cmd->scan_begin_arg =
+ COMBINE(cmd->scan_begin_arg, 0,
+ CR_FLAGS_MASK & ~(CR_EDGE | CR_INVERT));
err |= -EINVAL;
}
break;
@@ -1243,8 +1243,8 @@ static int pci230_handle_ao_fifo(struct comedi_device *dev,
* (otherwise there will be loads of "DAC FIFO not half full"
* interrupts).
*/
- if ((num_scans == 0) &&
- ((dacstat & PCI230P2_DAC_FIFO_HALF) == 0)) {
+ if (num_scans == 0 &&
+ (dacstat & PCI230P2_DAC_FIFO_HALF) == 0) {
dev_err(dev->class_dev, "AO buffer underrun\n");
events |= COMEDI_CB_OVERFLOW | COMEDI_CB_ERROR;
}
@@ -1541,8 +1541,8 @@ static int pci230_ai_check_scan_period(struct comedi_cmd *cmd)
chanlist_len = 1;
min_scan_period = chanlist_len * cmd->convert_arg;
- if ((min_scan_period < chanlist_len) ||
- (min_scan_period < cmd->convert_arg)) {
+ if (min_scan_period < chanlist_len ||
+ min_scan_period < cmd->convert_arg) {
/* Arithmetic overflow. */
min_scan_period = UINT_MAX;
err++;
@@ -1671,7 +1671,7 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
err |= cfc_check_trigger_src(&cmd->start_src, TRIG_NOW | TRIG_INT);
tmp = TRIG_FOLLOW | TRIG_TIMER | TRIG_INT;
- if ((thisboard->have_dio) || (thisboard->min_hwver > 0))
+ if (thisboard->have_dio || thisboard->min_hwver > 0)
/*
* Unfortunately, we cannot trigger a scan off an external
* source on the PCI260 board, since it uses the PPIC0 (DIO)
@@ -1701,8 +1701,8 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* If scan_begin_src is not TRIG_FOLLOW, then a monostable will be
* set up to generate a fixed number of timed conversion pulses.
*/
- if ((cmd->scan_begin_src != TRIG_FOLLOW) &&
- (cmd->convert_src != TRIG_TIMER))
+ if (cmd->scan_begin_src != TRIG_FOLLOW &&
+ cmd->convert_src != TRIG_TIMER)
err |= -EINVAL;
if (err)
@@ -1729,7 +1729,7 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* PCI230 or PCI260. Max speed depends whether
* single-ended or pseudo-differential.
*/
- if (cmd->chanlist && (cmd->chanlist_len > 0)) {
+ if (cmd->chanlist && cmd->chanlist_len > 0) {
/* Peek analogue reference of first channel. */
if (CR_AREF(cmd->chanlist[0]) == AREF_DIFF)
max_speed_ai = MAX_SPEED_AI_DIFF;
@@ -1768,13 +1768,12 @@ static int pci230_ai_cmdtest(struct comedi_device *dev,
* The only flags allowed are CR_INVERT and CR_EDGE.
* CR_EDGE is required.
*/
- if ((cmd->convert_arg &
- (CR_FLAGS_MASK & ~CR_INVERT)) != CR_EDGE) {
+ if ((cmd->convert_arg & CR_FLAGS_MASK & ~CR_INVERT) !=
+ CR_EDGE) {
/* Set CR_EDGE, preserve CR_INVERT. */
- cmd->convert_arg = COMBINE(cmd->start_arg,
- (CR_EDGE | 0),
- CR_FLAGS_MASK &
- ~CR_INVERT);
+ cmd->convert_arg =
+ COMBINE(cmd->start_arg, CR_EDGE | 0,
+ CR_FLAGS_MASK & ~CR_INVERT);
err |= -EINVAL;
}
} else {
@@ -1877,11 +1876,10 @@ static void pci230_ai_update_fifo_trigger_level(struct comedi_device *dev,
scanlen >= PCI230_ADC_FIFOLEVEL_HALFFULL)
wake = PCI230_ADC_FIFOLEVEL_HALFFULL;
else
- wake = (devpriv->ai_scan_count * scanlen) -
- devpriv->ai_scan_pos;
+ wake = devpriv->ai_scan_count * scanlen - devpriv->ai_scan_pos;
if (wake >= PCI230_ADC_FIFOLEVEL_HALFFULL) {
triglev = PCI230_ADC_INT_FIFO_HALF;
- } else if ((wake > 1) && (devpriv->hwver > 0)) {
+ } else if (wake > 1 && devpriv->hwver > 0) {
/* PCI230+/260+ programmable FIFO interrupt level. */
if (devpriv->adcfifothresh != wake) {
devpriv->adcfifothresh = wake;
@@ -1927,8 +1925,8 @@ static int pci230_ai_inttrig_convert(struct comedi_device *dev,
* bit has a different meaning when FIFO enabled (and when
* FIFO not enabled, it only works for software triggers).
*/
- if (((devpriv->adccon & PCI230_ADC_IM_MASK) ==
- PCI230_ADC_IM_DIF) && (devpriv->hwver == 0)) {
+ if ((devpriv->adccon & PCI230_ADC_IM_MASK) ==
+ PCI230_ADC_IM_DIF && devpriv->hwver == 0) {
/* PCI230/260 in differential mode */
delayus = 8;
} else {
@@ -2197,12 +2195,11 @@ static void pci230_handle_ai(struct comedi_device *dev,
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else if (devpriv->ai_scan_count == 0) {
todo = 0;
- } else if ((devpriv->ai_scan_count > PCI230_ADC_FIFOLEVEL_HALFFULL) ||
- (scanlen > PCI230_ADC_FIFOLEVEL_HALFFULL)) {
+ } else if (devpriv->ai_scan_count > PCI230_ADC_FIFOLEVEL_HALFFULL ||
+ scanlen > PCI230_ADC_FIFOLEVEL_HALFFULL) {
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
} else {
- todo = (devpriv->ai_scan_count * scanlen) -
- devpriv->ai_scan_pos;
+ todo = devpriv->ai_scan_count * scanlen - devpriv->ai_scan_pos;
if (todo > PCI230_ADC_FIFOLEVEL_HALFFULL)
todo = PCI230_ADC_FIFOLEVEL_HALFFULL;
}
@@ -2292,13 +2289,13 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
* Need Z2-CT2 to supply a conversion trigger source at a high
* logic level, even if not doing timed conversions.
*/
- res_mask |= (1U << RES_Z2CT2);
+ res_mask |= 1U << RES_Z2CT2;
if (cmd->scan_begin_src != TRIG_FOLLOW) {
/* Using Z2-CT0 monostable to gate Z2-CT2 conversion timer */
- res_mask |= (1U << RES_Z2CT0);
+ res_mask |= 1U << RES_Z2CT0;
if (cmd->scan_begin_src == TRIG_TIMER)
/* Using Z2-CT1 for scan frequency */
- res_mask |= (1U << RES_Z2CT1);
+ res_mask |= 1U << RES_Z2CT1;
}
/* Claim resources. */
if (!get_resources(dev, res_mask, OWNER_AICMD))
@@ -2370,7 +2367,7 @@ static int pci230_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
*/
adcen |= 1 << gainshift;
} else {
- gainshift = (chan & ~1);
+ gainshift = chan & ~1;
adcen |= 1 << chan;
}
devpriv->adcg = (devpriv->adcg & ~(3 << gainshift)) |
@@ -2689,8 +2686,7 @@ static int pci230_attach_common(struct comedi_device *dev,
* on PCI260[+].)
*/
extfunc |= PCI230P_EXTFUNC_GAT_EXTTRIG;
- if ((thisboard->ao_chans > 0) &&
- (devpriv->hwver >= 2))
+ if (thisboard->ao_chans > 0 && devpriv->hwver >= 2)
/* Enable DAC FIFO functionality. */
extfunc |= PCI230P2_EXTFUNC_DACFIFO;
}
--
2.0.0
On 2014-07-30 01:54, Hartley Sweeten wrote:
> On Tuesday, July 29, 2014 4:58 AM, Ian Abbott wrote:
>>
>> Tidy up the "amplc_pci230" driver a bit. There are more changes to come
>> after this. The only one of these that should alter the object code is
>> patch 06, which replaces a udelay() call with usleep_range().
>>
>> 01) staging: comedi: amplc_pci230: reformat a load of comments
>> 02) staging: comedi: amplc_pci230: fix checkpatch line over 80
>> characters
>> 03) staging: comedi: amplc_pci230: logical continuations should be on
>> the previous line
>> 04) staging: comedi: amplc_pci230: blank lines aren't necessary before a
>> close brace '}'
>> 05) staging: comedi: amplc_pci230: alignment should match open
>> parenthesis
>> 06) staging: comedi: amplc_pci230: usleep_range is preferred over udelay
>> 07) staging: comedi: amplc_pci230: remove unused settling time constants
>> 08) staging: comedi: amplc_pci230: remove PCI230_ADC_CONV
>> 09) staging: comedi: amplc_pci230: remove PCI230_TEST_BIT()
>> 10) staging: comedi: amplc_pci230: add whitespace to register values
>> 11) staging: comedi: amplc_pci230: don't begin line with binary operator
>> 12) staging: comedi: amplc_pci230: omit '!= 0' from logical expressions
>> 13) staging: comedi: amplc_pci230: remove unnecessary braces
>> 14) staging: comedi: amplc_pci230: remove some indentation in
>> pci230_ai_check_chanlist()
>> 15) staging: comedi: amplc_pci230: no need for '&function'
>> 16) staging: comedi: amplc_pci230: add whitespace to pci230_boards[]
>> 17) staging: comedi: amplc_pci230: no need to initialize named members
>> to zero
>> 18) staging: comedi: amplc_pci230: tidy up stuct pci230_private
>> 19) staging: comedi: amplc_pci230: remove some unnecessary parentheses
>>
>> drivers/staging/comedi/drivers/amplc_pci230.c | 1417 +++++++++++++------------
>> 1 file changed, 736 insertions(+), 681 deletions(-)
>
> Other than my comment about patch 13, this looks ok.
>
> Reviewed-by: H Hartley Sweeten <[email protected]>
I've posted v2 patches for patches 13 and 19. Patch 13 v2 is less
aggressive about brace removal. Patch 19 is updated to v2 because of
conflicts with the new patch 13.
--
-=( Ian Abbott @ MEV Ltd. E-mail: <[email protected]> )=-
-=( Tel: +44 (0)161 477 1898 FAX: +44 (0)161 718 3587 )=-
On Wed, Jul 30, 2014 at 12:53:47PM +0100, Ian Abbott wrote:
> Signed-off-by: Ian Abbott <[email protected]>
> ---
> v2: Be less aggressive in brace removal. Keep them for outer nested
> 'if's. Keep them in outer control statements where the inner control
> statement uses braces.
Really every multi-line indent should have braces for readability. This
isn't documented anywhere, but it's normal kernel style and Greg prefers
it for staging as well but I can't find the URL on google where he
mentioned that.
regards,
dan carpenter
On 2014-07-30 14:41, Dan Carpenter wrote:
> On Wed, Jul 30, 2014 at 12:53:47PM +0100, Ian Abbott wrote:
>> Signed-off-by: Ian Abbott <[email protected]>
>> ---
>> v2: Be less aggressive in brace removal. Keep them for outer nested
>> 'if's. Keep them in outer control statements where the inner control
>> statement uses braces.
>
> Really every multi-line indent should have braces for readability. This
> isn't documented anywhere, but it's normal kernel style and Greg prefers
> it for staging as well but I can't find the URL on google where he
> mentioned that.
With this version of the patch, amplc_pci230.c conforms to that -- as
long as you don't count comments, or splitting a simple statement across
multiple lines to fit within 80 columns, e.g.:
if (foo)
/* do this */
bar = baz +
qux;
--
-=( Ian Abbott @ MEV Ltd. E-mail: <[email protected]> )=-
-=( Tel: +44 (0)161 477 1898 FAX: +44 (0)161 718 3587 )=-
On Wed, Jul 30, 2014 at 03:04:03PM +0100, Ian Abbott wrote:
> On 2014-07-30 14:41, Dan Carpenter wrote:
> >On Wed, Jul 30, 2014 at 12:53:47PM +0100, Ian Abbott wrote:
> >>Signed-off-by: Ian Abbott <[email protected]>
> >>---
> >>v2: Be less aggressive in brace removal. Keep them for outer nested
> >>'if's. Keep them in outer control statements where the inner control
> >>statement uses braces.
> >
> >Really every multi-line indent should have braces for readability. This
> >isn't documented anywhere, but it's normal kernel style and Greg prefers
> >it for staging as well but I can't find the URL on google where he
> >mentioned that.
>
> With this version of the patch, amplc_pci230.c conforms to that --
> as long as you don't count comments, or splitting a simple statement
> across multiple lines to fit within 80 columns, e.g.:
>
> if (foo)
> /* do this */
> bar = baz +
> qux;
Heh... I am counting comments and broken lines, though. It's not a
totally strict rule and it's especially not strict for broken lines.
But we would prefer braces in those situations.
regards,
dan carpenter
On 2014-07-30 15:09, Dan Carpenter wrote:
> On Wed, Jul 30, 2014 at 03:04:03PM +0100, Ian Abbott wrote:
>> On 2014-07-30 14:41, Dan Carpenter wrote:
>>> On Wed, Jul 30, 2014 at 12:53:47PM +0100, Ian Abbott wrote:
>>>> Signed-off-by: Ian Abbott <[email protected]>
>>>> ---
>>>> v2: Be less aggressive in brace removal. Keep them for outer nested
>>>> 'if's. Keep them in outer control statements where the inner control
>>>> statement uses braces.
>>>
>>> Really every multi-line indent should have braces for readability. This
>>> isn't documented anywhere, but it's normal kernel style and Greg prefers
>>> it for staging as well but I can't find the URL on google where he
>>> mentioned that.
>>
>> With this version of the patch, amplc_pci230.c conforms to that --
>> as long as you don't count comments, or splitting a simple statement
>> across multiple lines to fit within 80 columns, e.g.:
>>
>> if (foo)
>> /* do this */
>> bar = baz +
>> qux;
>
> Heh... I am counting comments and broken lines, though. It's not a
> totally strict rule and it's especially not strict for broken lines.
> But we would prefer braces in those situations.
If necessary, patches 13 and 19 can be dropped entirely.
--
-=( Ian Abbott @ MEV Ltd. E-mail: <[email protected]> )=-
-=( Tel: +44 (0)161 477 1898 FAX: +44 (0)161 718 3587 )=-
On Wednesday, July 30, 2014 7:28 AM, Ian Abbott wrote:
> On 2014-07-30 15:09, Dan Carpenter wrote:
>> On Wed, Jul 30, 2014 at 03:04:03PM +0100, Ian Abbott wrote:
>>> On 2014-07-30 14:41, Dan Carpenter wrote:
>>>> On Wed, Jul 30, 2014 at 12:53:47PM +0100, Ian Abbott wrote:
>>>>> Signed-off-by: Ian Abbott <[email protected]>
>>>>> ---
>>>>> v2: Be less aggressive in brace removal. Keep them for outer nested
>>>>> 'if's. Keep them in outer control statements where the inner control
>>>>> statement uses braces.
>>>>
>>>> Really every multi-line indent should have braces for readability. This
>>>> isn't documented anywhere, but it's normal kernel style and Greg prefers
>>>> it for staging as well but I can't find the URL on google where he
>>>> mentioned that.
>>>
>>> With this version of the patch, amplc_pci230.c conforms to that --
>>> as long as you don't count comments, or splitting a simple statement
>>> across multiple lines to fit within 80 columns, e.g.:
>>>
>>> if (foo)
>>> /* do this */
>>> bar = baz +
>>> qux;
>>
>> Heh... I am counting comments and broken lines, though. It's not a
>> totally strict rule and it's especially not strict for broken lines.
>> But we would prefer braces in those situations.
>
> If necessary, patches 13 and 19 can be dropped entirely.
That might be best for now.
The rest of the series applies fine with them dropped.
Regards,
Hartley
On Wed, Jul 30, 2014 at 04:15:23PM +0000, Hartley Sweeten wrote:
> On Wednesday, July 30, 2014 7:28 AM, Ian Abbott wrote:
> > On 2014-07-30 15:09, Dan Carpenter wrote:
> >> On Wed, Jul 30, 2014 at 03:04:03PM +0100, Ian Abbott wrote:
> >>> On 2014-07-30 14:41, Dan Carpenter wrote:
> >>>> On Wed, Jul 30, 2014 at 12:53:47PM +0100, Ian Abbott wrote:
> >>>>> Signed-off-by: Ian Abbott <[email protected]>
> >>>>> ---
> >>>>> v2: Be less aggressive in brace removal. Keep them for outer nested
> >>>>> 'if's. Keep them in outer control statements where the inner control
> >>>>> statement uses braces.
> >>>>
> >>>> Really every multi-line indent should have braces for readability. This
> >>>> isn't documented anywhere, but it's normal kernel style and Greg prefers
> >>>> it for staging as well but I can't find the URL on google where he
> >>>> mentioned that.
> >>>
> >>> With this version of the patch, amplc_pci230.c conforms to that --
> >>> as long as you don't count comments, or splitting a simple statement
> >>> across multiple lines to fit within 80 columns, e.g.:
> >>>
> >>> if (foo)
> >>> /* do this */
> >>> bar = baz +
> >>> qux;
> >>
> >> Heh... I am counting comments and broken lines, though. It's not a
> >> totally strict rule and it's especially not strict for broken lines.
> >> But we would prefer braces in those situations.
> >
> > If necessary, patches 13 and 19 can be dropped entirely.
>
> That might be best for now.
>
> The rest of the series applies fine with them dropped.
Now dropped :)