From: Guanbing Huang <[email protected]>
The 16550a serial port based on the ACPI table requires obtaining the
reg-shift attribute. In the ACPI scenario, If the reg-shift property
is not configured like in DTS, the 16550a serial driver cannot read or
write controller registers properly during initialization.
Signed-off-by: Guanbing Huang <[email protected]>
Reviewed-by: Bing Fan <[email protected]>
Tested-by: Linheng Du <[email protected]>
---
v3 -> v4: dependent on two pre patches: "pnp: Add dev_is_pnp() macro" and
"serial: 8250_port: Add support of pnp irq to __uart_read_properties()",
the iotype is reserved, the mapsize is initialized, fix the UPF_SHARE_IRQ
flag, check for IRQ being absent
v2 -> v3: switch to use uart_read_port_properties(), change "Signed-off-by" to "Reviewed-by" and "Tested-by"
v1 -> v2: change the names after "Signed off by" to the real names
drivers/tty/serial/8250/8250_pnp.c | 36 ++++++++++++++++++++----------
1 file changed, 24 insertions(+), 12 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c
index 1974bbadc975..292cb8e84b37 100644
--- a/drivers/tty/serial/8250/8250_pnp.c
+++ b/drivers/tty/serial/8250/8250_pnp.c
@@ -435,6 +435,7 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
{
struct uart_8250_port uart, *port;
int ret, line, flags = dev_id->driver_data;
+ unsigned char iotype;
if (flags & UNKNOWN_DEV) {
ret = serial_pnp_guess_board(dev);
@@ -443,25 +444,31 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
}
memset(&uart, 0, sizeof(uart));
- if (pnp_irq_valid(dev, 0))
- uart.port.irq = pnp_irq(dev, 0);
if ((flags & CIR_PORT) && pnp_port_valid(dev, 2)) {
uart.port.iobase = pnp_port_start(dev, 2);
- uart.port.iotype = UPIO_PORT;
+ iotype = UPIO_PORT;
} else if (pnp_port_valid(dev, 0)) {
uart.port.iobase = pnp_port_start(dev, 0);
- uart.port.iotype = UPIO_PORT;
+ iotype = UPIO_PORT;
} else if (pnp_mem_valid(dev, 0)) {
uart.port.mapbase = pnp_mem_start(dev, 0);
- uart.port.iotype = UPIO_MEM;
+ uart.port.mapsize = pnp_mem_end(dev, 0) - pnp_mem_start(dev, 0);
+ iotype = UPIO_MEM;
uart.port.flags = UPF_IOREMAP;
} else
return -ENODEV;
- dev_dbg(&dev->dev,
- "Setup PNP port: port %#lx, mem %#llx, irq %u, type %u\n",
- uart.port.iobase, (unsigned long long)uart.port.mapbase,
- uart.port.irq, uart.port.iotype);
+ uart.port.uartclk = 1843200;
+ uart.port.dev = &dev->dev;
+
+ ret = uart_read_port_properties(&uart.port);
+ /* no interrupt -> fall back to polling */
+ if (ret == -ENXIO)
+ ret = 0;
+ if (ret)
+ return ret;
+
+ uart.port.iotype = iotype;
if (flags & CIR_PORT) {
uart.port.flags |= UPF_FIXED_PORT | UPF_FIXED_TYPE;
@@ -471,9 +478,14 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
uart.port.flags |= UPF_SHARE_IRQ;
- uart.port.uartclk = 1843200;
- device_property_read_u32(&dev->dev, "clock-frequency", &uart.port.uartclk);
- uart.port.dev = &dev->dev;
+ else
+ uart.port.flags &= ~UPF_SHARE_IRQ;
+
+
+ dev_dbg(&dev->dev,
+ "Setup PNP port: port %#lx, mem %#llx, size %#llx, irq %u, type %u\n",
+ uart.port.iobase, (unsigned long long)uart.port.mapbase,
+ (unsigned long long)uart.port.mapsize, uart.port.irq, uart.port.iotype);
line = serial8250_register_8250_port(&uart);
if (line < 0 || (flags & CIR_PORT))
--
2.17.1
On Wed, Apr 03, 2024 at 03:41:30PM +0800, Guanbing Huang wrote:
> From: Guanbing Huang <[email protected]>
>
> The 16550a serial port based on the ACPI table requires obtaining the
> reg-shift attribute. In the ACPI scenario, If the reg-shift property
> is not configured like in DTS, the 16550a serial driver cannot read or
> write controller registers properly during initialization.
..
> uart.port.mapbase = pnp_mem_start(dev, 0);
> + uart.port.mapsize = pnp_mem_end(dev, 0) - pnp_mem_start(dev, 0);
pnp_mem_len()
..
Add a comment here to explain that
/*
* The previous call may not set iotype correctly when reg-io-width
* property is absent and it doesn't support IO port resource.
*/
> + uart.port.iotype = iotype;
> uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
> if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
> uart.port.flags |= UPF_SHARE_IRQ;
> - uart.port.uartclk = 1843200;
> - device_property_read_u32(&dev->dev, "clock-frequency", &uart.port.uartclk);
> - uart.port.dev = &dev->dev;
> + else
> + uart.port.flags &= ~UPF_SHARE_IRQ;
This is not needed, just move
uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
to be before uart_read_properties().
--
With Best Regards,
Andy Shevchenko