Hi,
I get sometimes these kind of errors reading continously from CDs:
Nov 26 13:38:09 wl-193 kernel: hda: dma_timer_expiry: dma status == 0x24
Nov 26 13:38:19 wl-193 kernel: hda: DMA interrupt recovery
Nov 26 13:38:19 wl-193 kernel: hda: lost interrupt
and
Nov 26 16:16:50 wl-193 kernel: hdc: DMA interrupt recovery
Nov 26 16:16:50 wl-193 kernel: hdc: lost interrupt
This happens when I use Xine playing AVIs from CDs.
When it happens, it happens frequently, like once in every 5-10 minutes.
When I play an SVCD then it's less frequent than on data CDs,
like once in 30 minutes.
Drive is:
hdc: LITE-ON COMBO LTC-48161H, ATAPI CD/DVD-ROM drive
I haven't seen these kind of errors on my previous FC1/i386 system with
2.6.x kernels, I installed FC3/x86-64 recently. The original and the
second errata kernel both show this errors.
I also don't get this error on my harddisk.
Best regards,
Zolt?n B?sz?rm?nyi
Zoltan Boszormenyi ?rta:
> Hi,
>
> I get sometimes these kind of errors reading continously from CDs:
>
> Nov 26 13:38:09 wl-193 kernel: hda: dma_timer_expiry: dma status == 0x24
> Nov 26 13:38:19 wl-193 kernel: hda: DMA interrupt recovery
> Nov 26 13:38:19 wl-193 kernel: hda: lost interrupt
>
> and
>
> Nov 26 16:16:50 wl-193 kernel: hdc: DMA interrupt recovery
> Nov 26 16:16:50 wl-193 kernel: hdc: lost interrupt
>
> This happens when I use Xine playing AVIs from CDs.
> When it happens, it happens frequently, like once in every 5-10 minutes.
> When I play an SVCD then it's less frequent than on data CDs,
> like once in 30 minutes.
>
> Drive is:
>
> hdc: LITE-ON COMBO LTC-48161H, ATAPI CD/DVD-ROM drive
>
> I haven't seen these kind of errors on my previous FC1/i386 system with
> 2.6.x kernels, I installed FC3/x86-64 recently. The original and the
> second errata kernel both show this errors.
>
> I also don't get this error on my harddisk.
Sorry, this last statement is not true, just compare the two error
reports above. Both hda and hdc show this error.
>
> Best regards,
> Zolt?n B?sz?rm?nyi
>
On Sat, 27 Nov 2004, Zoltan Boszormenyi wrote:
> Sorry, this last statement is not true, just compare the two error
> reports above. Both hda and hdc show this error.
Please provide full dmesg, lspci and if possible state around which kernel
version the problems began occuring
Thanks,
Zwane
00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [80] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [c0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 1.02
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration
00: 06 11 88 31 06 00 30 22 01 00 00 06 00 08 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 88 31
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800 South] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: cfc00000-cfcfffff
Prefetchable memory behind bridge: 9fb00000-bfafffff
Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 88 b1 07 01 30 02 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 90 90 20 22
20: c0 cf c0 cf b0 9f a0 bf 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0e 00
00:05.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 02)
Subsystem: Avermedia Technologies Inc: Unknown device 0003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 169
Region 0: Memory at cfbfe000 (32-bit, prefetchable) [size=4K]
00: 9e 10 6e 03 06 00 80 02 02 00 00 04 00 20 80 00
10: 08 e0 bf cf 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 61 14 03 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 10 28
00:05.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 02)
Subsystem: Avermedia Technologies Inc: Unknown device 0003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 169
Region 0: Memory at cfbff000 (32-bit, prefetchable) [size=4K]
00: 9e 10 78 08 06 00 80 02 02 00 80 04 00 20 80 00
10: 08 f0 bf cf 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 61 14 03 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 04 ff
00:06.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE] (prog-if 00 [VGA])
Subsystem: PC Partner Limited: Unknown device 7c02
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 177
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at e000 [size=256]
Region 2: Memory at cffd0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at cff80000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 59 51 87 00 90 02 00 00 00 03 08 20 00 00
10: 08 00 00 c0 01 e0 00 00 00 00 fd cf 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 02 7c
30: 00 00 f8 cf 50 00 00 00 00 00 00 00 0a 01 08 00
00:08.0 Network controller: Intersil Corporation Prism 2.5 Wavelan chipset (rev 01)
Subsystem: Netgear MA311 802.11b wireless adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 185
Region 0: Memory at cfbfd000 (32-bit, prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 60 12 73 38 17 00 90 02 01 00 80 02 08 20 00 00
10: 08 d0 bf cf 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 85 13 05 41
30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 00 00
00:0a.0 Multimedia controller: Sigma Designs, Inc. REALmagic Hollywood Plus DVD Decoder (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 177
Region 0: Memory at cfe00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 05 11 00 83 06 00 10 02 02 00 80 04 00 20 00 00
10: 00 00 e0 cf 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00
40: 01 00 01 00 00 00 00 00
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at cfffbf00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at cff60000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: ec 10 69 81 17 00 b0 02 10 00 00 02 08 40 00 00
10: 01 dc 00 00 00 bf ff cf 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 2c 70
30: 00 00 f6 cf dc 00 00 00 00 00 00 00 0b 01 20 40
00:0d.0 RAID bus controller: Promise Technology, Inc. PDC20378 (FastTrak 378/SATA 378) (rev 02)
Subsystem: Micro-Star International Co., Ltd. K8T NEO FIS2R motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (1000ns min, 4500ns max), Cache Line Size 91
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at ec00 [size=64]
Region 1: I/O ports at e800 [size=16]
Region 2: I/O ports at e400 [size=128]
Region 3: Memory at cffef000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at cffa0000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 5a 10 73 33 17 00 30 02 02 00 04 01 91 60 00 00
10: 01 ec 00 00 01 e8 00 00 01 e4 00 00 00 f0 fe cf
20: 00 00 fa cf 00 00 00 00 00 00 00 00 62 14 2e 70
30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 04 12
00:0e.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 185
Region 0: Memory at cffee000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at d800 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 44 30 17 00 10 02 80 10 00 0c 08 20 00 00
10: 00 e0 fe cf 01 d8 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 2d 70
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 20
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
Subsystem: Micro-Star International Co., Ltd. K8T Neo 2 Motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin B routed to IRQ 193
Region 0: I/O ports at d400 [size=8]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at cc00 [size=8]
Region 3: I/O ports at c800 [size=4]
Region 4: I/O ports at c400 [size=16]
Region 5: I/O ports at c000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 49 31 07 00 90 02 80 00 04 01 00 20 80 00
10: 01 d4 00 00 01 d0 00 00 01 cc 00 00 01 c8 00 00
20: 01 c4 00 00 01 c0 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 02 00 00
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 193
Region 4: I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 fc 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 01 00 00
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 201
Region 4: I/O ports at b000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 b0 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 09 01 00 00
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 201
Region 4: I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 b4 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 09 01 00 00
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin B routed to IRQ 201
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 b8 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 09 02 00 00
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin B routed to IRQ 201
Region 4: I/O ports at bc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 bc 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 09 02 00 00
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 10
Interrupt: pin C routed to IRQ 201
Region 0: Memory at cfffbd00 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 04 31 17 00 10 02 86 20 03 0c 10 20 80 00
10: 00 bd ff cf 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 03 00 00
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800 South]
Subsystem: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800 South]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 27 32 87 00 10 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 27 32
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 209
Region 0: I/O ports at ac00 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 59 30 01 00 10 02 60 00 01 04 00 00 00 00
10: 01 ac 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 80 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 01 03 00 00
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00: 22 10 03 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (rev 01) (prog-if 00 [VGA])
Subsystem: PC Partner Limited: Unknown device 7c26
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 169
Region 0: Memory at b0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9800 [size=256]
Region 2: Memory at cfcf0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at cfcc0000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 64 59 07 00 b0 02 01 00 00 03 08 20 80 00
10: 08 00 00 b0 01 98 00 00 00 00 cf cf 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 26 7c
30: 00 00 cc cf 58 00 00 00 00 00 00 00 0b 01 08 00
01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 SE] (Secondary) (rev 01)
Subsystem: PC Partner Limited: Unknown device 7c27
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size 08
Region 0: Memory at a8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at cfce0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 44 5d 07 00 b0 02 01 00 80 03 08 20 00 00
10: 08 00 00 a8 00 00 ce cf 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 27 7c
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 08 00
On Sat, 27 Nov 2004, Zoltan Boszormenyi wrote:
> Zwane Mwaikambo ?rta:
> > On Sat, 27 Nov 2004, Zoltan Boszormenyi wrote:
> >
> >
> > > Sorry, this last statement is not true, just compare the two error
> > > reports above. Both hda and hdc show this error.
> >
> >
> > Please provide full dmesg, lspci and if possible state around which kernel
> > version the problems began occuring
> >
>
> They are attached. I am running the linuxconsole.sf.net multiconsole
> extension, I patched the Fedora Core 3 original and the second errata
> kernel with it and made a custom RPM.
Heavens =) Would it be possible for you to test latest -bk snapshot?
Thanks,
Zwane
Zwane Mwaikambo írta:
> On Sat, 27 Nov 2004, Zoltan Boszormenyi wrote:
>
>
>>Zwane Mwaikambo �rta:
>>
>>>On Sat, 27 Nov 2004, Zoltan Boszormenyi wrote:
>>>
>>>
>>>
>>>>Sorry, this last statement is not true, just compare the two error
>>>>reports above. Both hda and hdc show this error.
>>>
>>>
>>>Please provide full dmesg, lspci and if possible state around which kernel
>>>version the problems began occuring
>>>
>>
>>They are attached. I am running the linuxconsole.sf.net multiconsole
>>extension, I patched the Fedora Core 3 original and the second errata
>>kernel with it and made a custom RPM.
>
>
> Heavens =) Would it be possible for you to test latest -bk snapshot?
:-)
I will soon. Although I have to apply this patch also, more than one
person use my machine at once. My 2 and a half year old son would be
angry without his cartoons. ;-)
In the meantime it turned out that downing eth1 did not solve this
problem. The r8169 stopped spitting its messages but I still had one
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
in dmesg.
Best regards,
Zoltán Böszörményi
On Sat, 27 Nov 2004, Zoltan Boszormenyi wrote:
> I will soon. Although I have to apply this patch also, more than one
> person use my machine at once. My 2 and a half year old son would be
> angry without his cartoons. ;-)
>
> In the meantime it turned out that downing eth1 did not solve this
> problem. The r8169 stopped spitting its messages but I still had one
>
> hda: dma_timer_expiry: dma status == 0x24
> hda: DMA interrupt recovery
> hda: lost interrupt
Or you could try booting with acpi=off
Bootdata ok (command line is ro root=LABEL=/ dumbcon=1 rhgb acpi=off quiet)
Linux version 2.6.9-1.681ruby_FC3.root ([email protected]) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Wed Nov 24 20:26:05 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000cc000 - 00000000000d6000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
No mptable found.
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: VIA <6>Product ID: K8T400 <6>APIC at: 0xFEE00000
Processor #0 15:4 APIC version 17
I/O APIC #2 Version 3 at 0xFEC00000.
Processors: 1
Checking aperture...
CPU 0: aperture @ d0000000 size 128 MB
Built 1 zonelists
Kernel command line: ro root=LABEL=/ dumbcon=1 rhgb acpi=off quiet console=tty0
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 2000.138 MHz processor.
Console: Colour VGA+ 80x25 vc:1-16
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 509312k/524224k available (2408k kernel code, 14156k reserved, 1292k data, 164k init)
Calibrating delay loop... 3940.35 BogoMIPS (lpj=1970176)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 08
Using local APIC NMI watchdog using perfctr0
Using IO-APIC 2
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter disabled.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3227] at 0000:00:11.0
PCI->APIC IRQ transform: (B0,I5,P0) -> 137
PCI->APIC IRQ transform: (B0,I5,P0) -> 137
PCI->APIC IRQ transform: (B0,I6,P0) -> 145
PCI->APIC IRQ transform: (B0,I8,P0) -> 153
PCI->APIC IRQ transform: (B0,I10,P0) -> 145
PCI->APIC IRQ transform: (B0,I11,P0) -> 137
PCI->APIC IRQ transform: (B0,I13,P0) -> 145
PCI->APIC IRQ transform: (B0,I14,P0) -> 153
PCI->APIC IRQ transform: (B0,I15,P1) -> 145
PCI->APIC IRQ transform: (B0,I15,P0) -> 145
PCI->APIC IRQ transform: (B0,I16,P0) -> 161
PCI->APIC IRQ transform: (B0,I16,P0) -> 161
PCI->APIC IRQ transform: (B0,I16,P1) -> 161
PCI->APIC IRQ transform: (B0,I16,P1) -> 161
PCI->APIC IRQ transform: (B0,I16,P2) -> 161
PCI->APIC IRQ transform: (B0,I17,P2) -> 169
PCI->APIC IRQ transform: (B1,I0,P0) -> 137
agpgart: Detected AGP bridge 0
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xd0000000
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1101630820.170:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key A617AC2237592777
- User ID: Red Hat, Inc. (Kernel Module GPG key)
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 1
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 1
PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 1
PCI: Via IRQ fixup for 0000:00:11.5, from 3 to 9
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: probe of vesafb0 failed with error -6
Console: mono dummy device 80x25 vc:17-17
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: Maxtor 6Y120L0, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LITE-ON COMBO LTC-48161H, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
hdc: ATAPI 48X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
keyboard.c: [AT Raw Set 2 keyboard] vc:1-16
input: AT Raw Set 2 keyboard on isa0060/serio1
keyboard.c: [AT Translated Set 2 keyboard] vc:17-17
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 28Kbytes
TCP: Hash tables configured (established 32768 bind 4681)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09b)
powernow-k8: BIOS error - no PSB
Freeing unused kernel memory: 164k freed
SCSI subsystem initialized
libata version 1.02 loaded.
sata_via version 0.20
sata_via(0000:00:0f.0): routed to hard irq line 1
ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD002 bmdma 0xC400 irq 145
ata2: SATA max UDMA/133 cmd 0xCC00 ctl 0xC802 bmdma 0xC408 irq 145
ata1: no device found (phy stat 00000000)
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
sata_promise version 1.00
ata3: SATA max UDMA/133 cmd 0xFFFFFF0000054200 ctl 0xFFFFFF0000054238 bmdma 0x0 irq 145
ata4: SATA max UDMA/133 cmd 0xFFFFFF0000054280 ctl 0xFFFFFF00000542B8 bmdma 0x0 irq 145
ata3: no device found (phy stat 00000000)
scsi2 : sata_promise
ata4: no device found (phy stat 00000000)
scsi3 : sata_promise
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 4 roles, 280 types, 16 bools
security: 53 classes, 5494 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hda10, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for labeling
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
inserting floppy driver for 2.6.9-1.681ruby_FC3.root
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
orinoco 0.13e (David Gibson <[email protected]>, Pavel Roskin <[email protected]>, et al)
orinoco_pci 0.13e (Pavel Roskin <[email protected]>, David Gibson <[email protected]> & Jean Tourrilhes <[email protected]>)
orinoco_pci: Detected Orinoco/Prism2 PCI device at 0000:00:08.0, mem:0xCFBFD000 to 0xCFBFDFFF -> 0xffffff0000056000, irq:153
Reset done..............................................................................................................................................................................................................................................................;
Clear Reset............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................;
pci_cor : reg = 0x0 - FFFB9D4D - FFFB9B59
divert: allocating divert_blk for eth0
eth0: Station identity 001f:0006:0001:0003
eth0: Looks like an Intersil firmware version 1.3.6
eth0: Ad-hoc demo mode supported
eth0: IEEE standard IBSS ad-hoc mode supported
eth0: WEP supported, 104-bit key
eth0: MAC address 00:09:5B:91:B2:E4
eth0: Station name "Prism I"
eth0: ready
r8169 Gigabit Ethernet driver 1.2 loaded
r8169: NAPI enabled
divert: allocating divert_blk for eth1
eth1: Identified chip type is 'RTL8169s/8110s'.
eth1: RTL8169 at 0xffffff0000058f00, 00:0c:76:52:dc:54, IRQ 137
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
PCI: Setting latency timer of device 0000:00:11.5 to 64
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: irq 161, pci mem ffffff000007cd00
SELinux: initialized (dev usbdevfs, type usbdevfs), uses genfs_contexts
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: irq 161, io base 000000000000b000
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: irq 161, io base 000000000000b400
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: irq 161, io base 000000000000b800
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: irq 161, io base 000000000000bc00
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ohci1394: $Rev: 1223 $ Ben Collins <[email protected]>
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[153] MMIO=[cffee000-cffee7ff] Max Packet=[2048]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 3-1: new low speed USB device using address 2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:10.1-1
usb 3-2: new low speed USB device using address 3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00002c4af2]
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:10.1-2
EXT3 FS on hda10, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [email protected]
usb 5-2: new full speed USB device using address 2
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem hda2
Ending clean XFS mount for filesystem: hda2
SELinux: initialized (dev hda2, type xfs), uses xattr
XFS mounting filesystem hda5
Ending clean XFS mount for filesystem: hda5
SELinux: initialized (dev hda5, type xfs), uses xattr
XFS mounting filesystem hda7
Ending clean XFS mount for filesystem: hda7
SELinux: initialized (dev hda7, type xfs), uses xattr
XFS mounting filesystem hda11
Ending clean XFS mount for filesystem: hda11
SELinux: initialized (dev hda11, type xfs), uses xattr
XFS mounting filesystem hda6
Ending clean XFS mount for filesystem: hda6
SELinux: initialized (dev hda6, type xfs), uses xattr
XFS mounting filesystem hda9
Ending clean XFS mount for filesystem: hda9
SELinux: initialized (dev hda9, type xfs), uses xattr
XFS mounting filesystem hda8
Ending clean XFS mount for filesystem: hda8
SELinux: initialized (dev hda8, type xfs), uses xattr
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80452a20(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
Adding 522104k swap on /dev/hda3. Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2047 buckets, 16376 max) - 496 bytes per conntrack
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
eth0: New link status: Connected (0001)
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
i2c /dev entries driver
eth0: no IPv6 routers present
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
vmmon: module license 'unspecified' taints kernel.
vmmon: no version for "sys_ioctl" found: kernel tainted.
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
/dev/vmnet: open called by PID 3391 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth1: peer interface eth1 not found, will wait for it to come up
bridge-eth1: attached
/dev/vmnet: open called by PID 3414 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 5343 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
divert: allocating divert_blk for vmnet8
/dev/vmnet: open called by PID 5324 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
divert: allocating divert_blk for vmnet1
/dev/vmnet: open called by PID 5882 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 6097 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
[drm] Initialized radeon 1.11.0 20020828 on minor 0:
[drm] Initialized radeon 1.11.0 20020828 on minor 1:
vmnet8: no IPv6 routers present
vmnet1: no IPv6 routers present
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[drm] Loading R200 Microcode
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
SELinux: initialized (dev hdc, type iso9660), uses genfs_contexts
application mozilla-bin uses obsolete OSS audio interface
Losing some ticks... checking if CPU frequency changed.
warning: many lost ticks.
Your time source seems to be instable or some driver is hogging interupts
rip __do_softirq+0x41/0xa2
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
hda: dma_timer_expiry: dma status == 0x24
hda: DMA interrupt recovery
hda: lost interrupt
Zoltan Boszormenyi <[email protected]> wrote:
>
> Hi,
>
> I get sometimes these kind of errors reading continously from CDs:
>
> Nov 26 13:38:09 wl-193 kernel: hda: dma_timer_expiry: dma status == 0x24
> Nov 26 13:38:19 wl-193 kernel: hda: DMA interrupt recovery
> Nov 26 13:38:19 wl-193 kernel: hda: lost interrupt
>
> and
>
> Nov 26 16:16:50 wl-193 kernel: hdc: DMA interrupt recovery
> Nov 26 16:16:50 wl-193 kernel: hdc: lost interrupt
>
> This happens when I use Xine playing AVIs from CDs.
> When it happens, it happens frequently, like once in every 5-10 minutes.
> When I play an SVCD then it's less frequent than on data CDs,
> like once in 30 minutes.
>
> Drive is:
>
> hdc: LITE-ON COMBO LTC-48161H, ATAPI CD/DVD-ROM drive
>
> I haven't seen these kind of errors on my previous FC1/i386 system with
> 2.6.x kernels, I installed FC3/x86-64 recently. The original and the
> second errata kernel both show this errors.
>
> I also don't get this error on my harddisk.
Could we see the full boot log please? (ie: the dmesg output)