Hello,
After upgrading to 2.6.19-rc6 and enabling experimental support of
pata_via noticed that my hdd was downgraded to UDMA/33:
Before (2.6.18-rc & via82cxxx):
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override withidebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: VIA IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 16
VP_IDE: not 100%% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:07.1
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: max request size: 128KiB
hda: 40031712 sectors (20496 MB) w/512KiB Cache, CHS=39714/16/63, UDMA(66)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
Now (2.6.16-rc6 & pata_via):
pata_via 0000:00:07.1: version 0.1.14
ata1: PATA max UDMA/66 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15
scsi0 : pata_via
ata1.00: ATA-5, max UDMA/66, 40031712 sectors: LBA
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/33
scsi1 : pata_via
ata2: port is slow to respond, please be patient (Status 0xff)
ata2: port failed to respond (30 secs, Status 0xff)
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: reset failed, giving up
scsi 0:0:0:0: Direct-Access ATA FUJITSU MPF3204A 0031 PQ: 0 ANSI: 5
SCSI device sda: 40031712 512-byte hdwr sectors (20496 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 40031712 512-byte hdwr sectors (20496 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
sd 0:0:0:0: Attached scsi disk sda
# hdparm -I /dev/sda|grep dma
DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
BTW: is it possible to do something with this annoying long delay with
the "port is slow to respond, please be patient" message? :)
Best regards,
Krzysztof Ol?dzki
> ata1.00: ATA-5, max UDMA/66, 40031712 sectors: LBA
> ata1.00: ata1: dev 0 multi count 16
> ata1.00: configured for UDMA/33
Looks like a cable detect error.
> scsi1 : pata_via
> ata2: port is slow to respond, please be patient (Status 0xff)
> ata2: port failed to respond (30 secs, Status 0xff)
> ata2: SRST failed (status 0xFF)
> ata2: SRST failed (err_mask=0x100)
> ata2: softreset failed, retrying in 5 secs
> ata2: SRST failed (status 0xFF)
> ata2: SRST failed (err_mask=0x100)
> ata2: softreset failed, retrying in 5 secs
> ata2: SRST failed (status 0xFF)
This is a known bug in the libata core at the moment
> BTW: is it possible to do something with this annoying long delay with
> the "port is slow to respond, please be patient" message? :)
No, but it does appear to be a bug. Can you send me an lspci -vvxxx
Alan
On Sat, 25 Nov 2006, Alan wrote:
>> ata1.00: ATA-5, max UDMA/66, 40031712 sectors: LBA
>> ata1.00: ata1: dev 0 multi count 16
>> ata1.00: configured for UDMA/33
>
> Looks like a cable detect error.
Oh, indeed. Forcing ATA_CBL_PATA80 brings back expected UDMA66 speed.
>> scsi1 : pata_via
>> ata2: port is slow to respond, please be patient (Status 0xff)
>> ata2: port failed to respond (30 secs, Status 0xff)
>> ata2: SRST failed (status 0xFF)
>> ata2: SRST failed (err_mask=0x100)
>> ata2: softreset failed, retrying in 5 secs
>> ata2: SRST failed (status 0xFF)
>> ata2: SRST failed (err_mask=0x100)
>> ata2: softreset failed, retrying in 5 secs
>> ata2: SRST failed (status 0xFF)
>
> This is a known bug in the libata core at the moment
OK.
>> BTW: is it possible to do something with this annoying long delay with
>> the "port is slow to respond, please be patient" message? :)
>
> No, but it does appear to be a bug. Can you send me an lspci -vvxxx
00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133] (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 05 06 06 00 10 a2 01 00 00 06 00 00 00 00
10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: fd d8 c8 b6 05 00 18 18 08 80 00 00 08 10 14 18
60: 3c 0a c0 20 d5 e6 e6 00 43 38 86 2d 08 2f 00 00
70: c0 88 cc 0c 0e a1 d2 00 01 f4 09 02 00 00 00 08
80: 0f 40 00 00 c0 00 00 00 02 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 02 c0 20 00 07 02 00 1f 00 00 00 00 6b 02 04 00
b0: 7f ff 12 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 0a 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 22 42 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: dee00000-dfefffff
Prefetchable memory behind bridge: dcc00000-decfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 05 86 07 00 30 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 90 90 00 00
20: e0 de e0 df c0 dc c0 de 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 08 00
40: 48 cd 00 44 04 72 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 02 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 06 11 86 06 87 00 10 02 22 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 86 06
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 08 00 00 00 00 80 60 e6 01 00 c4 00 00 00 00 f3
50: 0e 06 34 00 00 00 a0 90 00 06 ff 08 50 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 05 30 00 02 00 00 04 08 00 00 00 00
80: 10 00 00 00 00 09 00 00 00 00 00 02 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Subsystem: GVC/BCM Advanced Research Unknown device 2129
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at ffa0 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 10 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 a4 14 29 21
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00
40: 03 f2 08 3a 0c 1f c0 00 a8 a8 a8 20 7f 00 ff 20
50: 0b 03 0b e2 14 00 00 00 a8 a8 a8 a8 00 00 00 00
60: 00 02 00 00 00 00 00 00 00 02 00 00 00 00 00 00
70: 02 01 00 00 00 00 00 00 82 01 00 00 00 00 00 00
80: 00 d0 3f 01 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 10 00 71 05 a4 14 29 21 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at cc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 01 10 02 10 00 03 0c 08 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 cc 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 09 04 00 00
40: 00 10 03 00 c6 00 30 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 17 01 10 02 10 00 03 0c 08 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 09 04 00 00
40: 00 10 03 00 c2 00 20 c0 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Subsystem: GVC/BCM Advanced Research Unknown device 2129
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 7
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 57 30 00 00 90 02 30 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 a4 14 29 21
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00
40: 20 84 57 00 5a 10 00 00 01 08 00 00 00 18 00 00
50: 00 df fe 00 10 00 00 00 00 ff fe 00 a4 14 29 21
60: 00 00 00 00 00 00 00 00 01 00 02 00 00 00 00 00
70: 01 0c 00 00 01 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 01 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 20)
Subsystem: GVC/BCM Advanced Research Unknown device 2129
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at d800 [size=4]
Region 2: I/O ports at d400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 58 30 01 00 10 02 20 00 01 04 00 00 00 00
10: 01 dc 00 00 01 d8 00 00 01 d4 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 a4 14 29 21
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 03 00 00
40: 01 c9 4b 1c 00 00 00 00 00 00 00 02 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:12.0 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
Subsystem: Intel Corporation PRO/1000 MT Dual Port Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at dffc0000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at c400 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 10 10 17 01 30 02 01 00 00 02 08 40 80 00
10: 04 00 fc df 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 c4 00 00 00 00 00 00 00 00 00 00 86 80 12 10
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 ff 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 e4 22 c8
e0: 00 20 00 28 07 f0 02 00 00 00 43 04 00 00 00 00
f0: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
00:12.1 Ethernet controller: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) (rev 01)
Subsystem: Intel Corporation PRO/1000 MT Dual Port Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 9
Region 0: Memory at dffe0000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at c800 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 10 10 17 01 30 02 01 00 00 02 08 40 80 00
10: 04 00 fe df 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 c8 00 00 00 00 00 00 00 00 00 00 86 80 12 10
30: 00 00 00 00 dc 00 00 00 00 00 00 00 09 02 ff 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 e4 22 c8
e0: 00 20 00 28 07 f0 02 00 01 00 43 04 00 00 00 00
f0: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev 03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G200 AGP
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at dd000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at dfefc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at dfee0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
00: 2b 10 21 05 07 00 90 02 03 00 00 03 08 40 00 00
10: 08 00 00 dd 00 c0 ef df 00 00 00 df 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 03 ff
30: 00 00 ee df dc 00 00 00 00 00 00 00 0b 01 10 20
40: 21 95 07 40 08 3c 00 00 00 00 4f 00 00 00 00 00
50: 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 f0 21 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 02 00 10 00 03 02 00 1f 02 03 00 1f 00 00 00 00
Best regards,
Krzysztof Ol?dzki
Does this fix it
--- drivers/ata/pata_via.c~ 2006-11-29 15:16:10.961387472 +0000
+++ drivers/ata/pata_via.c 2006-11-29 15:17:08.784597008 +0000
@@ -60,7 +60,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_via"
-#define DRV_VERSION "0.2.0"
+#define DRV_VERSION "0.2.1"
/*
* The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
@@ -159,10 +159,13 @@
return -ENOENT;
}
- if ((config->flags & VIA_UDMA) >= VIA_UDMA_66)
+ if ((config->flags & VIA_UDMA) >= VIA_UDMA_100)
ap->cbl = via_cable_detect(ap);
- else
+ /* The UDMA66 series has no cable detect so do drive side detect */
+ else if ((config->flags & VIA_UDMA) < VIA_UDMA_66)
ap->cbl = ATA_CBL_PATA40;
+
+
return ata_std_prereset(ap);
}
On Wed, 29 Nov 2006, Alan wrote:
> Does this fix it
>
> --- drivers/ata/pata_via.c~ 2006-11-29 15:16:10.961387472 +0000
> +++ drivers/ata/pata_via.c 2006-11-29 15:17:08.784597008 +0000
> @@ -60,7 +60,7 @@
> #include <linux/libata.h>
>
> #define DRV_NAME "pata_via"
> -#define DRV_VERSION "0.2.0"
> +#define DRV_VERSION "0.2.1"
>
> /*
> * The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
> @@ -159,10 +159,13 @@
> return -ENOENT;
> }
>
> - if ((config->flags & VIA_UDMA) >= VIA_UDMA_66)
> + if ((config->flags & VIA_UDMA) >= VIA_UDMA_100)
> ap->cbl = via_cable_detect(ap);
> - else
> + /* The UDMA66 series has no cable detect so do drive side detect */
> + else if ((config->flags & VIA_UDMA) < VIA_UDMA_66)
> ap->cbl = ATA_CBL_PATA40;
> +
> +
> return ata_std_prereset(ap);
> }
Yes and no - UDMA66 gets enabled, but with both 80-wire and 40-wire
cables.
* With 80-wire cable:
pata_via 0000:00:07.1: version 0.1.14
ata1: PATA max UDMA/66 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15
scsi0 : pata_via
ata1.00: ATA-5, max UDMA/66, 40031712 sectors: LBA
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/66
scsi1 : pata_via
ata2: port is slow to respond, please be patient (Status 0xff)
ata2: port failed to respond (30 secs, Status 0xff)
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: reset failed, giving up
scsi 0:0:0:0: Direct-Access ATA FUJITSU MPF3204A 0031 PQ: 0 ANSI: 5
SCSI device sda: 40031712 512-byte hdwr sectors (20496 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 40031712 512-byte hdwr sectors (20496 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
sd 0:0:0:0: Attached scsi disk sda
(...)
* With 40-wire cable:
pata_via 0000:00:07.1: version 0.1.14
ata1: PATA max UDMA/66 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15
scsi0 : pata_via
ata1.00: ATA-5, max UDMA/66, 40031712 sectors: LBA
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/66
scsi1 : pata_via
ata2: port is slow to respond, please be patient (Status 0xff)
ata2: port failed to respond (30 secs, Status 0xff)
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: softreset failed, retrying in 5 secs
ata2: SRST failed (status 0xFF)
ata2: SRST failed (err_mask=0x100)
ata2: reset failed, giving up
scsi 0:0:0:0: Direct-Access ATA FUJITSU MPF3204A 0031 PQ: 0 ANSI: 5
SCSI device sda: 40031712 512-byte hdwr sectors (20496 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 40031712 512-byte hdwr sectors (20496 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda:<3>ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x20)
ata1.00: tag 0 cmd 0xc8 Emask 0x10 stat 0x51 err 0x84 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x20)
ata1.00: tag 0 cmd 0xc8 Emask 0x10 stat 0x51 err 0x84 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x20)
ata1.00: tag 0 cmd 0xc8 Emask 0x10 stat 0x51 err 0x84 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/66
ata1: EH complete
ata1.00: limiting speed to UDMA/44
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
ata1.00: (BMDMA stat 0x20)
ata1.00: tag 0 cmd 0xc8 Emask 0x10 stat 0x51 err 0x84 (ATA bus error)
ata1: soft resetting port
ata1.00: configured for UDMA/44
ata1: EH complete
sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
sd 0:0:0:0: Attached scsi disk sda
Besr regards,
Krzysztof Ol?dzki