1. Export symbol on xhci_hub_control
2. Add hub_control to xhci_driver_overrides
3. Program USB2 pad PD controls during port connect/disconnect, port
suspend/resume, and test mode, to reduce power consumption on
disconnect or suspend.
Patch
xhci: tegra: USB2 pad power controls
depends on
xhci: hub: export symbol on xhci_hub_control
xhci: Add hub_control to xhci_driver_overrides
Jim Lin (3):
xhci: Add hub_control to xhci_driver_overrides
xhci: hub: export symbol on xhci_hub_control
xhci: tegra: USB2 pad power controls
drivers/usb/host/xhci-hub.c | 1 +
drivers/usb/host/xhci-tegra.c | 125 ++++++++++++++++++++++++++++++++++
drivers/usb/host/xhci.c | 2 +
drivers/usb/host/xhci.h | 2 +
4 files changed, 130 insertions(+)
--
2.17.1
From: Petlozu Pravareshwar <[email protected]>
Program USB2 pad PD controls during port connect/disconnect, port
suspend/resume, and test mode, to reduce power consumption on
disconnect or suspend.
Signed-off-by: Petlozu Pravareshwar <[email protected]>
Co-developed-by: Jim Lin <[email protected]>
Signed-off-by: Jim Lin <[email protected]>
---
v2: Fix issue that wrong tegra->phys[] may be accessed on tegra124
v3: No change on copyright
v4: Remove hcd_to_tegra_xusb() function which is used only once.
v5: Update .hub_control in tegra_xhci_overrides (xhci-tegra.c)
Invoke xhci_hub_control() directly (xhci-tegra.c)
v6: Change author to Petlozu
Changed from u32 to u8 for variable enable_utmi_pad_after_lp0_exit
Modified tegra_xhci_disable_phy_wake(), tegra_xhci_program_utmi_power_lp0_exit(),
tegra_xhci_hub_control()
v7: no change
drivers/usb/host/xhci-tegra.c | 125 ++++++++++++++++++++++++++++++++++
1 file changed, 125 insertions(+)
diff --git a/drivers/usb/host/xhci-tegra.c b/drivers/usb/host/xhci-tegra.c
index c8af2cd2216d..b5ed06ddbbac 100644
--- a/drivers/usb/host/xhci-tegra.c
+++ b/drivers/usb/host/xhci-tegra.c
@@ -274,6 +274,7 @@ struct tegra_xusb {
bool suspended;
struct tegra_xusb_context context;
+ u8 lp0_utmi_pad_mask;
};
static struct hc_driver __read_mostly tegra_xhci_hc_driver;
@@ -1951,10 +1952,24 @@ static void tegra_xhci_disable_phy_wake(struct tegra_xusb *tegra)
struct tegra_xusb_padctl *padctl = tegra->padctl;
unsigned int i;
+ for (i = 0; i < tegra->num_usb_phys; i++) {
+ struct phy *phy = tegra_xusb_get_phy(tegra, "usb2", i);
+
+ if (!phy)
+ continue;
+
+ if (tegra_xusb_padctl_remote_wake_detected(padctl, phy))
+ tegra_phy_xusb_utmi_pad_power_on(phy);
+ }
+
for (i = 0; i < tegra->num_phys; i++) {
if (!tegra->phys[i])
continue;
+ if (tegra_xusb_padctl_remote_wake_detected(padctl, tegra->phys[i]))
+ dev_dbg(tegra->dev, "%pOF remote wake detected\n",
+ tegra->phys[i]->dev.of_node);
+
tegra_xusb_padctl_disable_phy_wake(padctl, tegra->phys[i]);
}
}
@@ -1972,6 +1987,28 @@ static void tegra_xhci_disable_phy_sleepwalk(struct tegra_xusb *tegra)
}
}
+static void tegra_xhci_program_utmi_power_lp0_exit(struct tegra_xusb *tegra)
+{
+ unsigned int i, index_to_usb2;
+ struct phy *phy;
+
+ for (i = 0; i < tegra->soc->num_types; i++) {
+ if (strcmp(tegra->soc->phy_types[i].name, "usb2") == 0)
+ index_to_usb2 = i;
+ }
+
+ for (i = 0; i < tegra->num_usb_phys; i++) {
+ if (!is_host_mode_phy(tegra, index_to_usb2, i))
+ continue;
+
+ phy = tegra_xusb_get_phy(tegra, "usb2", i);
+ if (tegra->lp0_utmi_pad_mask & BIT(i))
+ tegra_phy_xusb_utmi_pad_power_on(phy);
+ else
+ tegra_phy_xusb_utmi_pad_power_down(phy);
+ }
+}
+
static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool runtime)
{
struct xhci_hcd *xhci = hcd_to_xhci(tegra->hcd);
@@ -1980,6 +2017,7 @@ static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool runtime)
unsigned int i;
int err;
u32 usbcmd;
+ u32 portsc;
dev_dbg(dev, "entering ELPG\n");
@@ -1993,6 +2031,15 @@ static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool runtime)
goto out;
}
+ for (i = 0; i < tegra->num_usb_phys; i++) {
+ if (!xhci->usb2_rhub.ports[i])
+ continue;
+ portsc = readl(xhci->usb2_rhub.ports[i]->addr);
+ tegra->lp0_utmi_pad_mask &= ~BIT(i);
+ if (((portsc & PORT_PLS_MASK) == XDEV_U3) || ((portsc & DEV_SPEED_MASK) == XDEV_FS))
+ tegra->lp0_utmi_pad_mask |= BIT(i);
+ }
+
err = xhci_suspend(xhci, wakeup);
if (err < 0) {
dev_err(tegra->dev, "failed to suspend XHCI: %d\n", err);
@@ -2066,6 +2113,8 @@ static int tegra_xusb_exit_elpg(struct tegra_xusb *tegra, bool runtime)
phy_power_on(tegra->phys[i]);
}
+ if (tegra->suspended)
+ tegra_xhci_program_utmi_power_lp0_exit(tegra);
tegra_xusb_config(tegra);
tegra_xusb_restore_context(tegra);
@@ -2437,8 +2486,84 @@ static int tegra_xhci_setup(struct usb_hcd *hcd)
return xhci_gen_setup(hcd, tegra_xhci_quirks);
}
+static int tegra_xhci_hub_control(struct usb_hcd *hcd, u16 type_req, u16 value, u16 index,
+ char *buf, u16 length)
+{
+ struct tegra_xusb *tegra = dev_get_drvdata(hcd->self.controller);
+ struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ struct xhci_hub *rhub;
+ struct xhci_bus_state *bus_state;
+ int port = (index & 0xff) - 1;
+ unsigned int i;
+ struct xhci_port **ports;
+ u32 portsc;
+ int ret;
+ struct phy *phy;
+
+ rhub = &xhci->usb2_rhub;
+ bus_state = &rhub->bus_state;
+ if (bus_state->resuming_ports && hcd->speed == HCD_USB2) {
+ ports = rhub->ports;
+ i = rhub->num_ports;
+ while (i--) {
+ if (!test_bit(i, &bus_state->resuming_ports))
+ continue;
+ portsc = readl(ports[i]->addr);
+ if ((portsc & PORT_PLS_MASK) == XDEV_RESUME)
+ tegra_phy_xusb_utmi_pad_power_on(
+ tegra_xusb_get_phy(tegra, "usb2", (int) i));
+ }
+ }
+
+ if (hcd->speed == HCD_USB2) {
+ phy = tegra_xusb_get_phy(tegra, "usb2", port);
+ if ((type_req == ClearPortFeature) && (value == USB_PORT_FEAT_SUSPEND)) {
+ if (!index || index > rhub->num_ports)
+ return -EPIPE;
+ tegra_phy_xusb_utmi_pad_power_on(phy);
+ }
+ if ((type_req == SetPortFeature) && (value == USB_PORT_FEAT_RESET)) {
+ if (!index || index > rhub->num_ports)
+ return -EPIPE;
+ ports = rhub->ports;
+ portsc = readl(ports[port]->addr);
+ if (portsc & PORT_CONNECT)
+ tegra_phy_xusb_utmi_pad_power_on(phy);
+ }
+ }
+
+ ret = xhci_hub_control(hcd, type_req, value, index, buf, length);
+ if (ret < 0)
+ return ret;
+
+ if (hcd->speed == HCD_USB2) {
+ /* Use phy where we set previously */
+ if ((type_req == SetPortFeature) && (value == USB_PORT_FEAT_SUSPEND))
+ /* We don't suspend the PAD while HNP role swap happens on the OTG port */
+ if (!((hcd->self.otg_port == (port + 1)) && hcd->self.b_hnp_enable))
+ tegra_phy_xusb_utmi_pad_power_down(phy);
+
+ if ((type_req == ClearPortFeature) && (value == USB_PORT_FEAT_C_CONNECTION)) {
+ ports = rhub->ports;
+ portsc = readl(ports[port]->addr);
+ if (!(portsc & PORT_CONNECT)) {
+ /* We don't suspend the PAD while HNP role swap happens on the OTG
+ * port
+ */
+ if (!((hcd->self.otg_port == (port + 1)) && hcd->self.b_hnp_enable))
+ tegra_phy_xusb_utmi_pad_power_down(phy);
+ }
+ }
+ if ((type_req == SetPortFeature) && (value == USB_PORT_FEAT_TEST))
+ tegra_phy_xusb_utmi_pad_power_on(phy);
+ }
+
+ return ret;
+}
+
static const struct xhci_driver_overrides tegra_xhci_overrides __initconst = {
.reset = tegra_xhci_setup,
+ .hub_control = tegra_xhci_hub_control,
};
static int __init tegra_xusb_init(void)
--
2.17.1
Add a hub_control() callback to the xhci_driver_overrides structure to
allow host drivers to override the default hub_control function. This
is required for Tegra which requires device specific actions for power
management to be executed during USB state transitions.
Signed-off-by: Jim Lin <[email protected]>
---
v5: new change
v6: adjust parameter alignment (xhci.h hub_control)
v7: change commit message
drivers/usb/host/xhci.c | 2 ++
drivers/usb/host/xhci.h | 2 ++
2 files changed, 4 insertions(+)
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 902f410874e8..3c7bf0a0e0b4 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -5461,6 +5461,8 @@ void xhci_init_driver(struct hc_driver *drv,
drv->check_bandwidth = over->check_bandwidth;
if (over->reset_bandwidth)
drv->reset_bandwidth = over->reset_bandwidth;
+ if (over->hub_control)
+ drv->hub_control = over->hub_control;
}
}
EXPORT_SYMBOL_GPL(xhci_init_driver);
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 5a75fe563123..f51b674fc10c 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1943,6 +1943,8 @@ struct xhci_driver_overrides {
struct usb_host_endpoint *ep);
int (*check_bandwidth)(struct usb_hcd *, struct usb_device *);
void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
+ int (*hub_control)(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
+ u16 wIndex, char *buf, u16 wLength);
};
#define XHCI_CFC_DELAY 10
--
2.17.1
On 11/11/2022 10:18, Jim Lin wrote:
> From: Petlozu Pravareshwar <[email protected]>
>
> Program USB2 pad PD controls during port connect/disconnect, port
> suspend/resume, and test mode, to reduce power consumption on
> disconnect or suspend.
>
> Signed-off-by: Petlozu Pravareshwar <[email protected]>
> Co-developed-by: Jim Lin <[email protected]>
> Signed-off-by: Jim Lin <[email protected]>
>
> ---
> v2: Fix issue that wrong tegra->phys[] may be accessed on tegra124
> v3: No change on copyright
> v4: Remove hcd_to_tegra_xusb() function which is used only once.
> v5: Update .hub_control in tegra_xhci_overrides (xhci-tegra.c)
> Invoke xhci_hub_control() directly (xhci-tegra.c)
> v6: Change author to Petlozu
> Changed from u32 to u8 for variable enable_utmi_pad_after_lp0_exit
> Modified tegra_xhci_disable_phy_wake(), tegra_xhci_program_utmi_power_lp0_exit(),
> tegra_xhci_hub_control()
> v7: no change
>
> drivers/usb/host/xhci-tegra.c | 125 ++++++++++++++++++++++++++++++++++
> 1 file changed, 125 insertions(+)
>
> diff --git a/drivers/usb/host/xhci-tegra.c b/drivers/usb/host/xhci-tegra.c
> index c8af2cd2216d..b5ed06ddbbac 100644
> --- a/drivers/usb/host/xhci-tegra.c
> +++ b/drivers/usb/host/xhci-tegra.c
> @@ -274,6 +274,7 @@ struct tegra_xusb {
>
> bool suspended;
> struct tegra_xusb_context context;
> + u8 lp0_utmi_pad_mask;
> };
>
> static struct hc_driver __read_mostly tegra_xhci_hc_driver;
> @@ -1951,10 +1952,24 @@ static void tegra_xhci_disable_phy_wake(struct tegra_xusb *tegra)
> struct tegra_xusb_padctl *padctl = tegra->padctl;
> unsigned int i;
>
> + for (i = 0; i < tegra->num_usb_phys; i++) {
> + struct phy *phy = tegra_xusb_get_phy(tegra, "usb2", i);
> +
> + if (!phy)
> + continue;
> +
> + if (tegra_xusb_padctl_remote_wake_detected(padctl, phy))
> + tegra_phy_xusb_utmi_pad_power_on(phy);
> + }
> +
> for (i = 0; i < tegra->num_phys; i++) {
> if (!tegra->phys[i])
> continue;
>
> + if (tegra_xusb_padctl_remote_wake_detected(padctl, tegra->phys[i]))
> + dev_dbg(tegra->dev, "%pOF remote wake detected\n",
> + tegra->phys[i]->dev.of_node);
> +
> tegra_xusb_padctl_disable_phy_wake(padctl, tegra->phys[i]);
> }
> }
> @@ -1972,6 +1987,28 @@ static void tegra_xhci_disable_phy_sleepwalk(struct tegra_xusb *tegra)
> }
> }
>
> +static void tegra_xhci_program_utmi_power_lp0_exit(struct tegra_xusb *tegra)
> +{
> + unsigned int i, index_to_usb2;
> + struct phy *phy;
> +
> + for (i = 0; i < tegra->soc->num_types; i++) {
> + if (strcmp(tegra->soc->phy_types[i].name, "usb2") == 0)
> + index_to_usb2 = i;
> + }
> +
> + for (i = 0; i < tegra->num_usb_phys; i++) {
> + if (!is_host_mode_phy(tegra, index_to_usb2, i))
> + continue;
> +
> + phy = tegra_xusb_get_phy(tegra, "usb2", i);
> + if (tegra->lp0_utmi_pad_mask & BIT(i))
> + tegra_phy_xusb_utmi_pad_power_on(phy);
> + else
> + tegra_phy_xusb_utmi_pad_power_down(phy);
> + }
> +}
> +
> static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool runtime)
> {
> struct xhci_hcd *xhci = hcd_to_xhci(tegra->hcd);
> @@ -1980,6 +2017,7 @@ static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool runtime)
> unsigned int i;
> int err;
> u32 usbcmd;
> + u32 portsc;
>
> dev_dbg(dev, "entering ELPG\n");
>
> @@ -1993,6 +2031,15 @@ static int tegra_xusb_enter_elpg(struct tegra_xusb *tegra, bool runtime)
> goto out;
> }
>
> + for (i = 0; i < tegra->num_usb_phys; i++) {
> + if (!xhci->usb2_rhub.ports[i])
> + continue;
> + portsc = readl(xhci->usb2_rhub.ports[i]->addr);
> + tegra->lp0_utmi_pad_mask &= ~BIT(i);
> + if (((portsc & PORT_PLS_MASK) == XDEV_U3) || ((portsc & DEV_SPEED_MASK) == XDEV_FS))
> + tegra->lp0_utmi_pad_mask |= BIT(i);
> + }
> +
> err = xhci_suspend(xhci, wakeup);
> if (err < 0) {
> dev_err(tegra->dev, "failed to suspend XHCI: %d\n", err);
> @@ -2066,6 +2113,8 @@ static int tegra_xusb_exit_elpg(struct tegra_xusb *tegra, bool runtime)
>
> phy_power_on(tegra->phys[i]);
> }
> + if (tegra->suspended)
> + tegra_xhci_program_utmi_power_lp0_exit(tegra);
>
> tegra_xusb_config(tegra);
> tegra_xusb_restore_context(tegra);
> @@ -2437,8 +2486,84 @@ static int tegra_xhci_setup(struct usb_hcd *hcd)
> return xhci_gen_setup(hcd, tegra_xhci_quirks);
> }
>
> +static int tegra_xhci_hub_control(struct usb_hcd *hcd, u16 type_req, u16 value, u16 index,
> + char *buf, u16 length)
> +{
> + struct tegra_xusb *tegra = dev_get_drvdata(hcd->self.controller);
> + struct xhci_hcd *xhci = hcd_to_xhci(hcd);
> + struct xhci_hub *rhub;
> + struct xhci_bus_state *bus_state;
> + int port = (index & 0xff) - 1;
> + unsigned int i;
> + struct xhci_port **ports;
> + u32 portsc;
> + int ret;
> + struct phy *phy;
> +
> + rhub = &xhci->usb2_rhub;
> + bus_state = &rhub->bus_state;
> + if (bus_state->resuming_ports && hcd->speed == HCD_USB2) {
> + ports = rhub->ports;
> + i = rhub->num_ports;
> + while (i--) {
> + if (!test_bit(i, &bus_state->resuming_ports))
> + continue;
> + portsc = readl(ports[i]->addr);
> + if ((portsc & PORT_PLS_MASK) == XDEV_RESUME)
> + tegra_phy_xusb_utmi_pad_power_on(
> + tegra_xusb_get_phy(tegra, "usb2", (int) i));
> + }
> + }
> +
> + if (hcd->speed == HCD_USB2) {
> + phy = tegra_xusb_get_phy(tegra, "usb2", port);
> + if ((type_req == ClearPortFeature) && (value == USB_PORT_FEAT_SUSPEND)) {
> + if (!index || index > rhub->num_ports)
> + return -EPIPE;
> + tegra_phy_xusb_utmi_pad_power_on(phy);
> + }
> + if ((type_req == SetPortFeature) && (value == USB_PORT_FEAT_RESET)) {
> + if (!index || index > rhub->num_ports)
> + return -EPIPE;
> + ports = rhub->ports;
> + portsc = readl(ports[port]->addr);
> + if (portsc & PORT_CONNECT)
> + tegra_phy_xusb_utmi_pad_power_on(phy);
> + }
> + }
> +
> + ret = xhci_hub_control(hcd, type_req, value, index, buf, length);
> + if (ret < 0)
> + return ret;
> +
> + if (hcd->speed == HCD_USB2) {
> + /* Use phy where we set previously */
> + if ((type_req == SetPortFeature) && (value == USB_PORT_FEAT_SUSPEND))
> + /* We don't suspend the PAD while HNP role swap happens on the OTG port */
> + if (!((hcd->self.otg_port == (port + 1)) && hcd->self.b_hnp_enable))
> + tegra_phy_xusb_utmi_pad_power_down(phy);
> +
> + if ((type_req == ClearPortFeature) && (value == USB_PORT_FEAT_C_CONNECTION)) {
> + ports = rhub->ports;
> + portsc = readl(ports[port]->addr);
> + if (!(portsc & PORT_CONNECT)) {
> + /* We don't suspend the PAD while HNP role swap happens on the OTG
> + * port
> + */
> + if (!((hcd->self.otg_port == (port + 1)) && hcd->self.b_hnp_enable))
> + tegra_phy_xusb_utmi_pad_power_down(phy);
> + }
> + }
> + if ((type_req == SetPortFeature) && (value == USB_PORT_FEAT_TEST))
> + tegra_phy_xusb_utmi_pad_power_on(phy);
> + }
> +
> + return ret;
> +}
> +
> static const struct xhci_driver_overrides tegra_xhci_overrides __initconst = {
> .reset = tegra_xhci_setup,
> + .hub_control = tegra_xhci_hub_control,
> };
>
> static int __init tegra_xusb_init(void)
Reviewed-by: Jon Hunter <[email protected]>
Tested-by: Jon Hunter <[email protected]>
Thanks
Jon
--
nvpublic
On 11/11/2022 10:18, Jim Lin wrote:
> Add a hub_control() callback to the xhci_driver_overrides structure to
> allow host drivers to override the default hub_control function. This
> is required for Tegra which requires device specific actions for power
> management to be executed during USB state transitions.
>
> Signed-off-by: Jim Lin <[email protected]>
>
> ---
> v5: new change
> v6: adjust parameter alignment (xhci.h hub_control)
> v7: change commit message
>
> drivers/usb/host/xhci.c | 2 ++
> drivers/usb/host/xhci.h | 2 ++
> 2 files changed, 4 insertions(+)
>
> diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
> index 902f410874e8..3c7bf0a0e0b4 100644
> --- a/drivers/usb/host/xhci.c
> +++ b/drivers/usb/host/xhci.c
> @@ -5461,6 +5461,8 @@ void xhci_init_driver(struct hc_driver *drv,
> drv->check_bandwidth = over->check_bandwidth;
> if (over->reset_bandwidth)
> drv->reset_bandwidth = over->reset_bandwidth;
> + if (over->hub_control)
> + drv->hub_control = over->hub_control;
> }
> }
> EXPORT_SYMBOL_GPL(xhci_init_driver);
> diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
> index 5a75fe563123..f51b674fc10c 100644
> --- a/drivers/usb/host/xhci.h
> +++ b/drivers/usb/host/xhci.h
> @@ -1943,6 +1943,8 @@ struct xhci_driver_overrides {
> struct usb_host_endpoint *ep);
> int (*check_bandwidth)(struct usb_hcd *, struct usb_device *);
> void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
> + int (*hub_control)(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
> + u16 wIndex, char *buf, u16 wLength);
> };
>
> #define XHCI_CFC_DELAY 10
Reviewed-by: Jon Hunter <[email protected]>
Tested-by: Jon Hunter <[email protected]>
Thanks
Jon
--
nvpublic
On Fri, Nov 11, 2022 at 06:18:13PM +0800, Jim Lin wrote:
> From: Petlozu Pravareshwar <[email protected]>
>
> Program USB2 pad PD controls during port connect/disconnect, port
> suspend/resume, and test mode, to reduce power consumption on
> disconnect or suspend.
>
> Signed-off-by: Petlozu Pravareshwar <[email protected]>
> Co-developed-by: Jim Lin <[email protected]>
> Signed-off-by: Jim Lin <[email protected]>
>
> ---
> v2: Fix issue that wrong tegra->phys[] may be accessed on tegra124
> v3: No change on copyright
> v4: Remove hcd_to_tegra_xusb() function which is used only once.
> v5: Update .hub_control in tegra_xhci_overrides (xhci-tegra.c)
> Invoke xhci_hub_control() directly (xhci-tegra.c)
> v6: Change author to Petlozu
> Changed from u32 to u8 for variable enable_utmi_pad_after_lp0_exit
> Modified tegra_xhci_disable_phy_wake(), tegra_xhci_program_utmi_power_lp0_exit(),
> tegra_xhci_hub_control()
> v7: no change
>
> drivers/usb/host/xhci-tegra.c | 125 ++++++++++++++++++++++++++++++++++
> 1 file changed, 125 insertions(+)
Acked-by: Thierry Reding <[email protected]>
On Fri, Nov 11, 2022 at 06:18:11PM +0800, Jim Lin wrote:
> Add a hub_control() callback to the xhci_driver_overrides structure to
> allow host drivers to override the default hub_control function. This
> is required for Tegra which requires device specific actions for power
> management to be executed during USB state transitions.
>
> Signed-off-by: Jim Lin <[email protected]>
>
> ---
> v5: new change
> v6: adjust parameter alignment (xhci.h hub_control)
> v7: change commit message
>
> drivers/usb/host/xhci.c | 2 ++
> drivers/usb/host/xhci.h | 2 ++
> 2 files changed, 4 insertions(+)
Acked-by: Thierry Reding <[email protected]>
Hi Greg,
On 11/11/2022 10:18, Jim Lin wrote:
> 1. Export symbol on xhci_hub_control
> 2. Add hub_control to xhci_driver_overrides
> 3. Program USB2 pad PD controls during port connect/disconnect, port
> suspend/resume, and test mode, to reduce power consumption on
> disconnect or suspend.
>
> Patch
> xhci: tegra: USB2 pad power controls
> depends on
> xhci: hub: export symbol on xhci_hub_control
> xhci: Add hub_control to xhci_driver_overrides
>
> Jim Lin (3):
> xhci: Add hub_control to xhci_driver_overrides
> xhci: hub: export symbol on xhci_hub_control
> xhci: tegra: USB2 pad power controls
>
> drivers/usb/host/xhci-hub.c | 1 +
> drivers/usb/host/xhci-tegra.c | 125 ++++++++++++++++++++++++++++++++++
> drivers/usb/host/xhci.c | 2 +
> drivers/usb/host/xhci.h | 2 +
> 4 files changed, 130 insertions(+)
>
I have verified that this still applies cleanly on top of -next. Please
let us know if this can be queued up for Linux v6.3?
Thanks
Jon
--
nvpublic
On Fri, Jan 06, 2023 at 02:56:51PM +0000, Jon Hunter wrote:
> Hi Greg,
>
> On 11/11/2022 10:18, Jim Lin wrote:
> > 1. Export symbol on xhci_hub_control
> > 2. Add hub_control to xhci_driver_overrides
> > 3. Program USB2 pad PD controls during port connect/disconnect, port
> > suspend/resume, and test mode, to reduce power consumption on
> > disconnect or suspend.
> >
> > Patch
> > xhci: tegra: USB2 pad power controls
> > depends on
> > xhci: hub: export symbol on xhci_hub_control
> > xhci: Add hub_control to xhci_driver_overrides
> >
> > Jim Lin (3):
> > xhci: Add hub_control to xhci_driver_overrides
> > xhci: hub: export symbol on xhci_hub_control
> > xhci: tegra: USB2 pad power controls
> >
> > drivers/usb/host/xhci-hub.c | 1 +
> > drivers/usb/host/xhci-tegra.c | 125 ++++++++++++++++++++++++++++++++++
> > drivers/usb/host/xhci.c | 2 +
> > drivers/usb/host/xhci.h | 2 +
> > 4 files changed, 130 insertions(+)
> >
>
>
> I have verified that this still applies cleanly on top of -next. Please let
> us know if this can be queued up for Linux v6.3?
Normally for xhci stuff I want it to go through Mathias for things that
are outside of just xhci-tegra.c.
thanks,
greg k-h
On 6.1.2023 17.25, Greg KH wrote:
> On Fri, Jan 06, 2023 at 02:56:51PM +0000, Jon Hunter wrote:
>> Hi Greg,
>>
>> On 11/11/2022 10:18, Jim Lin wrote:
>>> 1. Export symbol on xhci_hub_control
>>> 2. Add hub_control to xhci_driver_overrides
>>> 3. Program USB2 pad PD controls during port connect/disconnect, port
>>> suspend/resume, and test mode, to reduce power consumption on
>>> disconnect or suspend.
>>>
>>> Patch
>>> xhci: tegra: USB2 pad power controls
>>> depends on
>>> xhci: hub: export symbol on xhci_hub_control
>>> xhci: Add hub_control to xhci_driver_overrides
>>>
>>> Jim Lin (3):
>>> xhci: Add hub_control to xhci_driver_overrides
>>> xhci: hub: export symbol on xhci_hub_control
>>> xhci: tegra: USB2 pad power controls
>>>
>>> drivers/usb/host/xhci-hub.c | 1 +
>>> drivers/usb/host/xhci-tegra.c | 125 ++++++++++++++++++++++++++++++++++
>>> drivers/usb/host/xhci.c | 2 +
>>> drivers/usb/host/xhci.h | 2 +
>>> 4 files changed, 130 insertions(+)
>>>
>>
>>
>> I have verified that this still applies cleanly on top of -next. Please let
>> us know if this can be queued up for Linux v6.3?
>
> Normally for xhci stuff I want it to go through Mathias for things that
> are outside of just xhci-tegra.c.
Looks good to me, can be picked up directly
Acked-by: Mathias Nyman <[email protected]>
Or I can add this to the series going to usb-next if that is preferred.
Thanks
Mathias
>
> thanks,
>
> greg k-h
On 09/01/2023 08:28, Mathias Nyman wrote:
> On 6.1.2023 17.25, Greg KH wrote:
>> On Fri, Jan 06, 2023 at 02:56:51PM +0000, Jon Hunter wrote:
>>> Hi Greg,
>>>
>>> On 11/11/2022 10:18, Jim Lin wrote:
>>>> 1. Export symbol on xhci_hub_control
>>>> 2. Add hub_control to xhci_driver_overrides
>>>> 3. Program USB2 pad PD controls during port connect/disconnect, port
>>>> suspend/resume, and test mode, to reduce power consumption on
>>>> disconnect or suspend.
>>>>
>>>> Patch
>>>> xhci: tegra: USB2 pad power controls
>>>> depends on
>>>> xhci: hub: export symbol on xhci_hub_control
>>>> xhci: Add hub_control to xhci_driver_overrides
>>>>
>>>> Jim Lin (3):
>>>> xhci: Add hub_control to xhci_driver_overrides
>>>> xhci: hub: export symbol on xhci_hub_control
>>>> xhci: tegra: USB2 pad power controls
>>>>
>>>> drivers/usb/host/xhci-hub.c | 1 +
>>>> drivers/usb/host/xhci-tegra.c | 125
>>>> ++++++++++++++++++++++++++++++++++
>>>> drivers/usb/host/xhci.c | 2 +
>>>> drivers/usb/host/xhci.h | 2 +
>>>> 4 files changed, 130 insertions(+)
>>>>
>>>
>>>
>>> I have verified that this still applies cleanly on top of -next.
>>> Please let
>>> us know if this can be queued up for Linux v6.3?
>>
>> Normally for xhci stuff I want it to go through Mathias for things that
>> are outside of just xhci-tegra.c.
>
> Looks good to me, can be picked up directly
> Acked-by: Mathias Nyman <[email protected]>
>
> Or I can add this to the series going to usb-next if that is preferred.
I did not see this in -next yet.
Mathias, are you able to pick this up?
Thanks Jon
--
nvpublic
On Mon, Jan 16, 2023 at 11:50:19AM +0000, Jon Hunter wrote:
>
> On 09/01/2023 08:28, Mathias Nyman wrote:
> > On 6.1.2023 17.25, Greg KH wrote:
> > > On Fri, Jan 06, 2023 at 02:56:51PM +0000, Jon Hunter wrote:
> > > > Hi Greg,
> > > >
> > > > On 11/11/2022 10:18, Jim Lin wrote:
> > > > > 1. Export symbol on xhci_hub_control
> > > > > 2. Add hub_control to xhci_driver_overrides
> > > > > 3. Program USB2 pad PD controls during port connect/disconnect, port
> > > > > suspend/resume, and test mode, to reduce power consumption on
> > > > > disconnect or suspend.
> > > > >
> > > > > Patch
> > > > > xhci: tegra: USB2 pad power controls
> > > > > depends on
> > > > > xhci: hub: export symbol on xhci_hub_control
> > > > > xhci: Add hub_control to xhci_driver_overrides
> > > > >
> > > > > Jim Lin (3):
> > > > > ??? xhci: Add hub_control to xhci_driver_overrides
> > > > > ??? xhci: hub: export symbol on xhci_hub_control
> > > > > ??? xhci: tegra: USB2 pad power controls
> > > > >
> > > > > ?? drivers/usb/host/xhci-hub.c?? |?? 1 +
> > > > > ?? drivers/usb/host/xhci-tegra.c | 125
> > > > > ++++++++++++++++++++++++++++++++++
> > > > > ?? drivers/usb/host/xhci.c?????? |?? 2 +
> > > > > ?? drivers/usb/host/xhci.h?????? |?? 2 +
> > > > > ?? 4 files changed, 130 insertions(+)
> > > > >
> > > >
> > > >
> > > > I have verified that this still applies cleanly on top of -next.
> > > > Please let
> > > > us know if this can be queued up for Linux v6.3?
> > >
> > > Normally for xhci stuff I want it to go through Mathias for things that
> > > are outside of just xhci-tegra.c.
> >
> > Looks good to me, can be picked up directly
> > Acked-by: Mathias Nyman <[email protected]>
> >
> > Or I can add this to the series going to usb-next if that is preferred.
>
>
> I did not see this in -next yet.
>
> Mathias, are you able to pick this up?
I will when I catch up with linux-usb patches this week, sorry for the
delay, too many fires this early in the year...