From: Arnd Bergmann <[email protected]>
The w5100/w5300 drivers only support probing with old platform data in
MMIO mode, or probing with DT in SPI mode. There are no users of this
platform data in tree, and from the git history it appears that the only
users of MMIO mode were on the (since removed) blackfin architecture.
Remove the platform data option, as it's unlikely to still be needed, and
change the internal operation to GPIO descriptors, making the behavior
the same for SPI and MMIO mode. The other data in the platform_data
structure is the MAC address, so make that also handled the same for both.
It would probably be possible to just remove the MMIO mode driver
completely, but it seems fine otherwise, and fixing it to use the modern
interface seems easy enough.
Signed-off-by: Arnd Bergmann <[email protected]>
---
.../devicetree/bindings/net/wiznet,w5x00.txt | 4 +-
drivers/net/ethernet/wiznet/w5100-spi.c | 21 ++-----
drivers/net/ethernet/wiznet/w5100.c | 57 ++++++++++---------
drivers/net/ethernet/wiznet/w5100.h | 3 +-
drivers/net/ethernet/wiznet/w5300.c | 52 ++++++++++-------
include/linux/platform_data/wiznet.h | 23 --------
6 files changed, 70 insertions(+), 90 deletions(-)
delete mode 100644 include/linux/platform_data/wiznet.h
diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
index e9665798c4be..e8a802d65817 100644
--- a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
+++ b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
@@ -1,6 +1,6 @@
* Wiznet w5x00
-This is a standalone 10/100 MBit Ethernet controller with SPI interface.
+This is a standalone 10/100 MBit Ethernet controller with SPI or MMIO interface.
For each device connected to a SPI bus, define a child node within
the SPI master node.
@@ -9,6 +9,7 @@ Required properties:
- compatible: Should be one of the following strings:
"wiznet,w5100"
"wiznet,w5200"
+ "wiznet,w5300"
"wiznet,w5500"
- reg: Specify the SPI chip select the chip is wired to.
- interrupts: Specify the interrupt index within the interrupt controller (referred
@@ -25,6 +26,7 @@ Optional properties:
According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however,
board designs may need to limit this value.
- local-mac-address: See ethernet.txt in the same directory.
+- link-gpios: a GPIO line used for the link detection interrupt
Example (for Raspberry Pi with pin control stuff for GPIO irq):
diff --git a/drivers/net/ethernet/wiznet/w5100-spi.c b/drivers/net/ethernet/wiznet/w5100-spi.c
index 7c52796273a4..81ac52f0fe50 100644
--- a/drivers/net/ethernet/wiznet/w5100-spi.c
+++ b/drivers/net/ethernet/wiznet/w5100-spi.c
@@ -423,23 +423,12 @@ static int w5100_spi_probe(struct spi_device *spi)
const struct of_device_id *of_id;
const struct w5100_ops *ops;
kernel_ulong_t driver_data;
- const void *mac = NULL;
- u8 tmpmac[ETH_ALEN];
int priv_size;
- int ret;
- ret = of_get_mac_address(spi->dev.of_node, tmpmac);
- if (!ret)
- mac = tmpmac;
-
- if (spi->dev.of_node) {
- of_id = of_match_device(w5100_of_match, &spi->dev);
- if (!of_id)
- return -ENODEV;
- driver_data = (kernel_ulong_t)of_id->data;
- } else {
- driver_data = spi_get_device_id(spi)->driver_data;
- }
+ of_id = of_match_device(w5100_of_match, &spi->dev);
+ if (!of_id)
+ return -ENODEV;
+ driver_data = (kernel_ulong_t)of_id->data;
switch (driver_data) {
case W5100:
@@ -458,7 +447,7 @@ static int w5100_spi_probe(struct spi_device *spi)
return -EINVAL;
}
- return w5100_probe(&spi->dev, ops, priv_size, mac, spi->irq, -EINVAL);
+ return w5100_probe(&spi->dev, ops, priv_size, spi->irq);
}
static void w5100_spi_remove(struct spi_device *spi)
diff --git a/drivers/net/ethernet/wiznet/w5100.c b/drivers/net/ethernet/wiznet/w5100.c
index 634946e87e5f..11c448f78193 100644
--- a/drivers/net/ethernet/wiznet/w5100.c
+++ b/drivers/net/ethernet/wiznet/w5100.c
@@ -11,7 +11,6 @@
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/platform_device.h>
-#include <linux/platform_data/wiznet.h>
#include <linux/ethtool.h>
#include <linux/skbuff.h>
#include <linux/types.h>
@@ -24,6 +23,7 @@
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/gpio.h>
+#include <linux/of_net.h>
#include "w5100.h"
@@ -139,6 +139,12 @@ MODULE_LICENSE("GPL");
#define W5500_RX_MEM_START 0x30000
#define W5500_RX_MEM_SIZE 0x04000
+#ifndef CONFIG_WIZNET_BUS_SHIFT
+#define CONFIG_WIZNET_BUS_SHIFT 0
+#endif
+
+#define W5100_BUS_DIRECT_SIZE (0x8000 << CONFIG_WIZNET_BUS_SHIFT)
+
/*
* Device driver private data structure
*/
@@ -157,7 +163,7 @@ struct w5100_priv {
int irq;
int link_irq;
- int link_gpio;
+ struct gpio_desc *link_gpio;
struct napi_struct napi;
struct net_device *ndev;
@@ -729,8 +735,8 @@ static u32 w5100_get_link(struct net_device *ndev)
{
struct w5100_priv *priv = netdev_priv(ndev);
- if (gpio_is_valid(priv->link_gpio))
- return !!gpio_get_value(priv->link_gpio);
+ if (priv->link_gpio)
+ return !!gpiod_get_value(priv->link_gpio);
return 1;
}
@@ -943,7 +949,7 @@ static irqreturn_t w5100_detect_link(int irq, void *ndev_instance)
struct w5100_priv *priv = netdev_priv(ndev);
if (netif_running(ndev)) {
- if (gpio_get_value(priv->link_gpio) != 0) {
+ if (gpiod_get_value(priv->link_gpio) != 0) {
netif_info(priv, link, ndev, "link is up\n");
netif_carrier_on(ndev);
} else {
@@ -998,8 +1004,8 @@ static int w5100_open(struct net_device *ndev)
w5100_hw_start(priv);
napi_enable(&priv->napi);
netif_start_queue(ndev);
- if (!gpio_is_valid(priv->link_gpio) ||
- gpio_get_value(priv->link_gpio) != 0)
+ if (!priv->link_gpio ||
+ gpiod_get_value(priv->link_gpio) != 0)
netif_carrier_on(ndev);
return 0;
}
@@ -1037,15 +1043,10 @@ static const struct net_device_ops w5100_netdev_ops = {
static int w5100_mmio_probe(struct platform_device *pdev)
{
- struct wiznet_platform_data *data = dev_get_platdata(&pdev->dev);
- const void *mac_addr = NULL;
struct resource *mem;
const struct w5100_ops *ops;
int irq;
- if (data && is_valid_ether_addr(data->mac_addr))
- mac_addr = data->mac_addr;
-
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!mem)
return -EINVAL;
@@ -1058,8 +1059,7 @@ static int w5100_mmio_probe(struct platform_device *pdev)
if (irq < 0)
return irq;
- return w5100_probe(&pdev->dev, ops, sizeof(struct w5100_mmio_priv),
- mac_addr, irq, data ? data->link_gpio : -EINVAL);
+ return w5100_probe(&pdev->dev, ops, sizeof(struct w5100_mmio_priv), irq);
}
static int w5100_mmio_remove(struct platform_device *pdev)
@@ -1077,13 +1077,13 @@ void *w5100_ops_priv(const struct net_device *ndev)
EXPORT_SYMBOL_GPL(w5100_ops_priv);
int w5100_probe(struct device *dev, const struct w5100_ops *ops,
- int sizeof_ops_priv, const void *mac_addr, int irq,
- int link_gpio)
+ int sizeof_ops_priv, int irq)
{
struct w5100_priv *priv;
struct net_device *ndev;
int err;
size_t alloc_size;
+ u8 tmpmac[ETH_ALEN];
alloc_size = sizeof(*priv);
if (sizeof_ops_priv) {
@@ -1129,7 +1129,9 @@ int w5100_probe(struct device *dev, const struct w5100_ops *ops,
priv->ndev = ndev;
priv->ops = ops;
priv->irq = irq;
- priv->link_gpio = link_gpio;
+ priv->link_gpio = gpiod_get_optional(dev, "link", GPIOD_IN);
+ if (IS_ERR(priv->link_gpio))
+ return PTR_ERR(priv->link_gpio);
ndev->netdev_ops = &w5100_netdev_ops;
ndev->ethtool_ops = &w5100_ethtool_ops;
@@ -1156,8 +1158,9 @@ int w5100_probe(struct device *dev, const struct w5100_ops *ops,
INIT_WORK(&priv->setrx_work, w5100_setrx_work);
INIT_WORK(&priv->restart_work, w5100_restart_work);
- if (mac_addr)
- eth_hw_addr_set(ndev, mac_addr);
+ err = of_get_mac_address(dev->of_node, tmpmac);
+ if (!err)
+ eth_hw_addr_set(ndev, tmpmac);
else
eth_hw_addr_random(ndev);
@@ -1182,7 +1185,7 @@ int w5100_probe(struct device *dev, const struct w5100_ops *ops,
if (err)
goto err_hw;
- if (gpio_is_valid(priv->link_gpio)) {
+ if (priv->link_gpio) {
char *link_name = devm_kzalloc(dev, 16, GFP_KERNEL);
if (!link_name) {
@@ -1190,12 +1193,14 @@ int w5100_probe(struct device *dev, const struct w5100_ops *ops,
goto err_gpio;
}
snprintf(link_name, 16, "%s-link", netdev_name(ndev));
- priv->link_irq = gpio_to_irq(priv->link_gpio);
+ priv->link_irq = gpiod_to_irq(priv->link_gpio);
if (request_any_context_irq(priv->link_irq, w5100_detect_link,
IRQF_TRIGGER_RISING |
IRQF_TRIGGER_FALLING,
- link_name, priv->ndev) < 0)
- priv->link_gpio = -EINVAL;
+ link_name, priv->ndev) < 0) {
+ gpiod_put(priv->link_gpio);
+ priv->link_gpio = NULL;
+ }
}
return 0;
@@ -1219,7 +1224,7 @@ void w5100_remove(struct device *dev)
w5100_hw_reset(priv);
free_irq(priv->irq, ndev);
- if (gpio_is_valid(priv->link_gpio))
+ if (priv->link_gpio)
free_irq(priv->link_irq, ndev);
flush_work(&priv->setrx_work);
@@ -1256,8 +1261,8 @@ static int w5100_resume(struct device *dev)
w5100_hw_start(priv);
netif_device_attach(ndev);
- if (!gpio_is_valid(priv->link_gpio) ||
- gpio_get_value(priv->link_gpio) != 0)
+ if (!priv->link_gpio ||
+ gpiod_get_value(priv->link_gpio) != 0)
netif_carrier_on(ndev);
}
return 0;
diff --git a/drivers/net/ethernet/wiznet/w5100.h b/drivers/net/ethernet/wiznet/w5100.h
index 481af3b6d9e8..013ef2835115 100644
--- a/drivers/net/ethernet/wiznet/w5100.h
+++ b/drivers/net/ethernet/wiznet/w5100.h
@@ -29,8 +29,7 @@ struct w5100_ops {
void *w5100_ops_priv(const struct net_device *ndev);
int w5100_probe(struct device *dev, const struct w5100_ops *ops,
- int sizeof_ops_priv, const void *mac_addr, int irq,
- int link_gpio);
+ int sizeof_ops_priv, int irq);
void w5100_remove(struct device *dev);
extern const struct dev_pm_ops w5100_pm_ops;
diff --git a/drivers/net/ethernet/wiznet/w5300.c b/drivers/net/ethernet/wiznet/w5300.c
index b0958fe8111e..9fcf50926d62 100644
--- a/drivers/net/ethernet/wiznet/w5300.c
+++ b/drivers/net/ethernet/wiznet/w5300.c
@@ -12,7 +12,6 @@
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/platform_device.h>
-#include <linux/platform_data/wiznet.h>
#include <linux/ethtool.h>
#include <linux/skbuff.h>
#include <linux/types.h>
@@ -24,7 +23,8 @@
#include <linux/ioport.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/of_net.h>
#define DRV_NAME "w5300"
#define DRV_VERSION "2012-04-04"
@@ -80,6 +80,12 @@ MODULE_LICENSE("GPL");
#define W5300_S0_RX_FIFO 0x0230 /* S0 Receive FIFO */
#define W5300_REGS_LEN 0x0400
+#ifndef CONFIG_WIZNET_BUS_SHIFT
+#define CONFIG_WIZNET_BUS_SHIFT 0
+#endif
+
+#define W5300_BUS_DIRECT_SIZE (0x0400 << CONFIG_WIZNET_BUS_SHIFT)
+
/*
* Device driver private data structure
*/
@@ -91,7 +97,7 @@ struct w5300_priv {
void (*write)(struct w5300_priv *priv, u16 addr, u16 data);
int irq;
int link_irq;
- int link_gpio;
+ struct gpio_desc *link_gpio;
struct napi_struct napi;
struct net_device *ndev;
@@ -292,8 +298,8 @@ static u32 w5300_get_link(struct net_device *ndev)
{
struct w5300_priv *priv = netdev_priv(ndev);
- if (gpio_is_valid(priv->link_gpio))
- return !!gpio_get_value(priv->link_gpio);
+ if (priv->link_gpio)
+ return !!gpiod_get_value(priv->link_gpio);
return 1;
}
@@ -442,7 +448,7 @@ static irqreturn_t w5300_detect_link(int irq, void *ndev_instance)
struct w5300_priv *priv = netdev_priv(ndev);
if (netif_running(ndev)) {
- if (gpio_get_value(priv->link_gpio) != 0) {
+ if (gpiod_get_value(priv->link_gpio) != 0) {
netif_info(priv, link, ndev, "link is up\n");
netif_carrier_on(ndev);
} else {
@@ -485,8 +491,8 @@ static int w5300_open(struct net_device *ndev)
w5300_hw_start(priv);
napi_enable(&priv->napi);
netif_start_queue(ndev);
- if (!gpio_is_valid(priv->link_gpio) ||
- gpio_get_value(priv->link_gpio) != 0)
+ if (!priv->link_gpio ||
+ gpiod_get_value(priv->link_gpio) != 0)
netif_carrier_on(ndev);
return 0;
}
@@ -524,7 +530,6 @@ static const struct net_device_ops w5300_netdev_ops = {
static int w5300_hw_probe(struct platform_device *pdev)
{
- struct wiznet_platform_data *data = dev_get_platdata(&pdev->dev);
struct net_device *ndev = platform_get_drvdata(pdev);
struct w5300_priv *priv = netdev_priv(ndev);
const char *name = netdev_name(ndev);
@@ -533,11 +538,9 @@ static int w5300_hw_probe(struct platform_device *pdev)
int irq;
int ret;
- if (data && is_valid_ether_addr(data->mac_addr)) {
- eth_hw_addr_set(ndev, data->mac_addr);
- } else {
- eth_hw_addr_random(ndev);
- }
+ ret = of_get_ethdev_address(pdev->dev.of_node, ndev);
+ if (ret)
+ eth_hw_addr_random(ndev);
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
priv->base = devm_ioremap_resource(&pdev->dev, mem);
@@ -569,17 +572,22 @@ static int w5300_hw_probe(struct platform_device *pdev)
return ret;
priv->irq = irq;
- priv->link_gpio = data ? data->link_gpio : -EINVAL;
- if (gpio_is_valid(priv->link_gpio)) {
+ priv->link_gpio = gpiod_get_optional(&pdev->dev, "link", GPIOD_IN);
+ if (IS_ERR(priv->link_gpio))
+ return PTR_ERR(priv->link_gpio);
+
+ if (priv->link_gpio) {
char *link_name = devm_kzalloc(&pdev->dev, 16, GFP_KERNEL);
if (!link_name)
return -ENOMEM;
snprintf(link_name, 16, "%s-link", name);
- priv->link_irq = gpio_to_irq(priv->link_gpio);
+ priv->link_irq = gpiod_to_irq(priv->link_gpio);
if (request_any_context_irq(priv->link_irq, w5300_detect_link,
IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- link_name, priv->ndev) < 0)
- priv->link_gpio = -EINVAL;
+ link_name, priv->ndev) < 0) {
+ priv->link_gpio = NULL;
+ gpiod_put(priv->link_gpio);
+ }
}
netdev_info(ndev, "at 0x%llx irq %d\n", (u64)mem->start, irq);
@@ -634,7 +642,7 @@ static int w5300_remove(struct platform_device *pdev)
w5300_hw_reset(priv);
free_irq(priv->irq, ndev);
- if (gpio_is_valid(priv->link_gpio))
+ if (priv->link_gpio)
free_irq(priv->link_irq, ndev);
unregister_netdev(ndev);
@@ -667,8 +675,8 @@ static int w5300_resume(struct device *dev)
w5300_hw_start(priv);
netif_device_attach(ndev);
- if (!gpio_is_valid(priv->link_gpio) ||
- gpio_get_value(priv->link_gpio) != 0)
+ if (!priv->link_gpio ||
+ gpiod_get_value(priv->link_gpio) != 0)
netif_carrier_on(ndev);
}
return 0;
diff --git a/include/linux/platform_data/wiznet.h b/include/linux/platform_data/wiznet.h
deleted file mode 100644
index 1154c4db8a13..000000000000
--- a/include/linux/platform_data/wiznet.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Ethernet driver for the WIZnet W5x00 chip.
- */
-
-#ifndef PLATFORM_DATA_WIZNET_H
-#define PLATFORM_DATA_WIZNET_H
-
-#include <linux/if_ether.h>
-
-struct wiznet_platform_data {
- int link_gpio;
- u8 mac_addr[ETH_ALEN];
-};
-
-#ifndef CONFIG_WIZNET_BUS_SHIFT
-#define CONFIG_WIZNET_BUS_SHIFT 0
-#endif
-
-#define W5100_BUS_DIRECT_SIZE (0x8000 << CONFIG_WIZNET_BUS_SHIFT)
-#define W5300_BUS_DIRECT_SIZE (0x0400 << CONFIG_WIZNET_BUS_SHIFT)
-
-#endif /* PLATFORM_DATA_WIZNET_H */
--
2.39.0
On Thu, Jan 26, 2023 at 02:54:12PM +0100, Arnd Bergmann wrote:
> From: Arnd Bergmann <[email protected]>
>
> The w5100/w5300 drivers only support probing with old platform data in
> MMIO mode, or probing with DT in SPI mode. There are no users of this
> platform data in tree, and from the git history it appears that the only
> users of MMIO mode were on the (since removed) blackfin architecture.
>
> Remove the platform data option, as it's unlikely to still be needed, and
> change the internal operation to GPIO descriptors, making the behavior
> the same for SPI and MMIO mode. The other data in the platform_data
> structure is the MAC address, so make that also handled the same for both.
>
> It would probably be possible to just remove the MMIO mode driver
> completely, but it seems fine otherwise, and fixing it to use the modern
> interface seems easy enough.
>
> Signed-off-by: Arnd Bergmann <[email protected]>
> ---
> .../devicetree/bindings/net/wiznet,w5x00.txt | 4 +-
> drivers/net/ethernet/wiznet/w5100-spi.c | 21 ++-----
> drivers/net/ethernet/wiznet/w5100.c | 57 ++++++++++---------
> drivers/net/ethernet/wiznet/w5100.h | 3 +-
> drivers/net/ethernet/wiznet/w5300.c | 52 ++++++++++-------
> include/linux/platform_data/wiznet.h | 23 --------
> 6 files changed, 70 insertions(+), 90 deletions(-)
> delete mode 100644 include/linux/platform_data/wiznet.h
<...>
> #include "w5100.h"
>
> @@ -139,6 +139,12 @@ MODULE_LICENSE("GPL");
> #define W5500_RX_MEM_START 0x30000
> #define W5500_RX_MEM_SIZE 0x04000
>
> +#ifndef CONFIG_WIZNET_BUS_SHIFT
> +#define CONFIG_WIZNET_BUS_SHIFT 0
> +#endif
I don't see any define of CONFIG_WIZNET_BUS_SHIFT in the code, so it looks
like it always zero and can be removed.
Thanks
On Thu, Jan 26, 2023, at 19:14, Leon Romanovsky wrote:
> On Thu, Jan 26, 2023 at 02:54:12PM +0100, Arnd Bergmann wrote:
>>
>> @@ -139,6 +139,12 @@ MODULE_LICENSE("GPL");
>> #define W5500_RX_MEM_START 0x30000
>> #define W5500_RX_MEM_SIZE 0x04000
>>
>> +#ifndef CONFIG_WIZNET_BUS_SHIFT
>> +#define CONFIG_WIZNET_BUS_SHIFT 0
>> +#endif
>
> I don't see any define of CONFIG_WIZNET_BUS_SHIFT in the code, so it looks
> like it always zero and can be removed.
Good catch! Evidently the original idea was that this would
be set to a machine specific value through Kconfig. I've renamed
the constant, removed the #ifdef and explained it in the changelog
text now.
Arnd