The 'objs' is for user space tools, for the kernel modules
we should use 'y'.
Signed-off-by: Andy Shevchenko <[email protected]>
---
drivers/platform/surface/aggregator/Makefile | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/drivers/platform/surface/aggregator/Makefile b/drivers/platform/surface/aggregator/Makefile
index c8498c41e758..ce548dba1d4b 100644
--- a/drivers/platform/surface/aggregator/Makefile
+++ b/drivers/platform/surface/aggregator/Makefile
@@ -6,12 +6,12 @@ CFLAGS_core.o = -I$(src)
obj-$(CONFIG_SURFACE_AGGREGATOR) += surface_aggregator.o
-surface_aggregator-objs := core.o
-surface_aggregator-objs += ssh_parser.o
-surface_aggregator-objs += ssh_packet_layer.o
-surface_aggregator-objs += ssh_request_layer.o
-surface_aggregator-objs += controller.o
+surface_aggregator-y := core.o
+surface_aggregator-y += ssh_parser.o
+surface_aggregator-y += ssh_packet_layer.o
+surface_aggregator-y += ssh_request_layer.o
+surface_aggregator-y += controller.o
ifeq ($(CONFIG_SURFACE_AGGREGATOR_BUS),y)
-surface_aggregator-objs += bus.o
+surface_aggregator-y += bus.o
endif
--
2.30.2
On 8/3/21 7:50 PM, Andy Shevchenko wrote:
> The 'objs' is for user space tools, for the kernel modules
> we should use 'y'.
>
> Signed-off-by: Andy Shevchenko <[email protected]>
Thank you! I was previously not aware of that distinction. Two small
notes:
- There is a typo in the subject line.
- With that change, the ifeq could be placed in-line (see note below).
All in all looks good to me (assuming the typo gets fixed).
Reviewed-by: Maximilian Luz <[email protected]>
> ---
> drivers/platform/surface/aggregator/Makefile | 12 ++++++------
> 1 file changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/platform/surface/aggregator/Makefile b/drivers/platform/surface/aggregator/Makefile
> index c8498c41e758..ce548dba1d4b 100644
> --- a/drivers/platform/surface/aggregator/Makefile
> +++ b/drivers/platform/surface/aggregator/Makefile
> @@ -6,12 +6,12 @@ CFLAGS_core.o = -I$(src)
>
> obj-$(CONFIG_SURFACE_AGGREGATOR) += surface_aggregator.o
>
> -surface_aggregator-objs := core.o
> -surface_aggregator-objs += ssh_parser.o
> -surface_aggregator-objs += ssh_packet_layer.o
> -surface_aggregator-objs += ssh_request_layer.o
> -surface_aggregator-objs += controller.o
> +surface_aggregator-y := core.o
> +surface_aggregator-y += ssh_parser.o
> +surface_aggregator-y += ssh_packet_layer.o
> +surface_aggregator-y += ssh_request_layer.o
> +surface_aggregator-y += controller.o
>
> ifeq ($(CONFIG_SURFACE_AGGREGATOR_BUS),y)
> -surface_aggregator-objs += bus.o
> +surface_aggregator-y += bus.o
> endif
I believe it should now be possible to write this as
surface_aggregator-$(CONFIG_SURFACE_AGGREGATOR_BUS) += bus.o
which might be a bit cleaner. Don't have much of a preference though so
I'd also be fine with keeping the ifeq.
Regards,
Max
On Tue, Aug 03, 2021 at 08:40:10PM +0200, Maximilian Luz wrote:
> On 8/3/21 7:50 PM, Andy Shevchenko wrote:
> > The 'objs' is for user space tools, for the kernel modules
> > we should use 'y'.
> >
> > Signed-off-by: Andy Shevchenko <[email protected]>
>
> Thank you! I was previously not aware of that distinction. Two small
> notes:
>
> - There is a typo in the subject line.
> - With that change, the ifeq could be placed in-line (see note below).
Will address both.
> All in all looks good to me (assuming the typo gets fixed).
>
> Reviewed-by: Maximilian Luz <[email protected]>
Thanks!
--
With Best Regards,
Andy Shevchenko