From: Carlos Song <[email protected]>
I2C bus recovery need a pinmux and gpio. So i2c driver can switch
gpio mode to toggle scl to recovery bus.
Add pinctrl-single node to every i2c bus on fsl-ls2160 layerscape
platform.
Signed-off-by: Carlos Song <[email protected]>
Reviewed-by: Frank Li <[email protected]>
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
index e665c629e1a1..96055593204a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -748,7 +748,10 @@ i2c0: i2c@2000000 {
clock-names = "i2c";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
- scl-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c0_scl>;
+ pinctrl-1 = <&i2c0_scl_gpio>;
+ scl-gpios = <&gpio0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -761,6 +764,10 @@ i2c1: i2c@2010000 {
clock-names = "i2c";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c1_scl>;
+ pinctrl-1 = <&i2c1_scl_gpio>;
+ scl-gpios = <&gpio0 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -773,6 +780,10 @@ i2c2: i2c@2020000 {
clock-names = "i2c";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c2_scl>;
+ pinctrl-1 = <&i2c2_scl_gpio>;
+ scl-gpios = <&gpio0 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -785,6 +796,10 @@ i2c3: i2c@2030000 {
clock-names = "i2c";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c3_scl>;
+ pinctrl-1 = <&i2c3_scl_gpio>;
+ scl-gpios = <&gpio0 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -797,7 +812,10 @@ i2c4: i2c@2040000 {
clock-names = "i2c";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
- scl-gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c4_scl>;
+ pinctrl-1 = <&i2c4_scl_gpio>;
+ scl-gpios = <&gpio0 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -810,6 +828,10 @@ i2c5: i2c@2050000 {
clock-names = "i2c";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c5_scl>;
+ pinctrl-1 = <&i2c5_scl_gpio>;
+ scl-gpios = <&gpio0 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -822,6 +844,10 @@ i2c6: i2c@2060000 {
clock-names = "i2c";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c6_scl>;
+ pinctrl-1 = <&i2c6_scl_gpio>;
+ scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -834,6 +860,10 @@ i2c7: i2c@2070000 {
clock-names = "i2c";
clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
QORIQ_CLK_PLL_DIV(16)>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&i2c7_scl>;
+ pinctrl-1 = <&i2c7_scl_gpio>;
+ scl-gpios = <&gpio1 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
};
@@ -1669,6 +1699,80 @@ pcs18: ethernet-phy@0 {
};
};
+ pinmux_i2crv: pinmux@70010012c {
+ compatible = "pinctrl-single";
+ reg = <0x00000007 0x0010012c 0x0 0xc>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ pinctrl-single,bit-per-mux;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x7>;
+
+ i2c1_scl: i2c1-scl-pins {
+ pinctrl-single,bits = <0x0 0 0x7>;
+ };
+
+ i2c1_scl_gpio: i2c1-scl-gpio-pins {
+ pinctrl-single,bits = <0x0 0x1 0x7>;
+ };
+
+ i2c2_scl: i2c2-scl-pins {
+ pinctrl-single,bits = <0x0 0 (0x7 << 3)>;
+ };
+
+ i2c2_scl_gpio: i2c2-scl-gpio-pins {
+ pinctrl-single,bits = <0x0 (0x1 << 3) (0x7 << 3)>;
+ };
+
+ i2c3_scl: i2c3-scl-pins {
+ pinctrl-single,bits = <0x0 0 (0x7 << 6)>;
+ };
+
+ i2c3_scl_gpio: i2c3-scl-gpio-pins {
+ pinctrl-single,bits = <0x0 (0x1 << 6) (0x7 << 6)>;
+ };
+
+ i2c4_scl: i2c4-scl-pins {
+ pinctrl-single,bits = <0x0 0 (0x7 << 9)>;
+ };
+
+ i2c4_scl_gpio: i2c4-scl-gpio-pins {
+ pinctrl-single,bits = <0x0 (0x1 << 9) (0x7 << 9)>;
+ };
+
+ i2c5_scl: i2c5-scl-pins {
+ pinctrl-single,bits = <0x0 0 (0x7 << 12)>;
+ };
+
+ i2c5_scl_gpio: i2c5-scl-gpio-pins {
+ pinctrl-single,bits = <0x0 (0x1 << 12) (0x7 << 12)>;
+ };
+
+ i2c6_scl: i2c6-scl-pins {
+ pinctrl-single,bits = <0x4 0x2 0x7>;
+ };
+
+ i2c6_scl_gpio: i2c6-scl-gpio-pins {
+ pinctrl-single,bits = <0x4 0x1 0x7>;
+ };
+
+ i2c7_scl: i2c7-scl-pins {
+ pinctrl-single,bits = <0x4 0x2 0x7>;
+ };
+
+ i2c7_scl_gpio: i2c7-scl-gpio-pins {
+ pinctrl-single,bits = <0x4 0x1 0x7>;
+ };
+
+ i2c0_scl: i2c0-scl-pins {
+ pinctrl-single,bits = <0x8 0 (0x7 << 10)>;
+ };
+
+ i2c0_scl_gpio: i2c0-scl-gpio-pins {
+ pinctrl-single,bits = <0x8 (0x1 << 10) (0x7 << 10)>;
+ };
+ };
+
fsl_mc: fsl-mc@80c000000 {
compatible = "fsl,qoriq-mc";
reg = <0x00000008 0x0c000000 0 0x40>,
--
2.34.1
On Thu, Mar 28, 2024 at 02:14:19PM +0800, [email protected] wrote:
> From: Carlos Song <[email protected]>
>
> I2C bus recovery need a pinmux and gpio. So i2c driver can switch
> gpio mode to toggle scl to recovery bus.
>
> Add pinctrl-single node to every i2c bus on fsl-ls2160 layerscape
> platform.
>
> Signed-off-by: Carlos Song <[email protected]>
> Reviewed-by: Frank Li <[email protected]>
Applied, thanks!