In case this PHY is bootstrapped for managed mode, we need to manually
wake it. Otherwise no link will be detected.
Cc: [email protected]
Fixes: cb80ee2f9bee1 ("net: phy: Add support for the DP83TG720S Ethernet PHY")
Signed-off-by: Oleksij Rempel <[email protected]>
---
drivers/net/phy/dp83tg720.c | 18 +++++++++++++++---
1 file changed, 15 insertions(+), 3 deletions(-)
diff --git a/drivers/net/phy/dp83tg720.c b/drivers/net/phy/dp83tg720.c
index 326c9770a6dcc..1186dfc70fb3c 100644
--- a/drivers/net/phy/dp83tg720.c
+++ b/drivers/net/phy/dp83tg720.c
@@ -17,6 +17,11 @@
#define DP83TG720S_PHY_RESET 0x1f
#define DP83TG720S_HW_RESET BIT(15)
+#define DP83TG720S_LPS_CFG3 0x18c
+/* Power modes are documented as bit fields but used as values */
+/* Power Mode 0 is Normal mode */
+#define DP83TG720S_LPS_CFG3_PWR_MODE_0 BIT(0)
+
#define DP83TG720S_RGMII_DELAY_CTRL 0x602
/* In RGMII mode, Enable or disable the internal delay for RXD */
#define DP83TG720S_RGMII_RX_CLK_SEL BIT(1)
@@ -154,10 +159,17 @@ static int dp83tg720_config_init(struct phy_device *phydev)
*/
usleep_range(1000, 2000);
- if (phy_interface_is_rgmii(phydev))
- return dp83tg720_config_rgmii_delay(phydev);
+ if (phy_interface_is_rgmii(phydev)) {
+ ret = dp83tg720_config_rgmii_delay(phydev);
+ if (ret)
+ return ret;
+ }
- return 0;
+ /* In case the PHY is bootstrapped in managed mode, we need to
+ * wake it.
+ */
+ return phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_LPS_CFG3,
+ DP83TG720S_LPS_CFG3_PWR_MODE_0);
}
static struct phy_driver dp83tg720_driver[] = {
--
2.39.2
Get initial master/slave configuration, otherwise ethtool
wont be able to provide this information until link is
established. This makes troubleshooting harder, since wrong
role configuration would prevent the link start.
Fixes: cb80ee2f9bee1 ("net: phy: Add support for the DP83TG720S Ethernet PHY")
Cc: [email protected]
Signed-off-by: Oleksij Rempel <[email protected]>
---
drivers/net/phy/dp83tg720.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/net/phy/dp83tg720.c b/drivers/net/phy/dp83tg720.c
index 1186dfc70fb3c..84256827a03bf 100644
--- a/drivers/net/phy/dp83tg720.c
+++ b/drivers/net/phy/dp83tg720.c
@@ -168,8 +168,12 @@ static int dp83tg720_config_init(struct phy_device *phydev)
/* In case the PHY is bootstrapped in managed mode, we need to
* wake it.
*/
- return phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_LPS_CFG3,
- DP83TG720S_LPS_CFG3_PWR_MODE_0);
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_LPS_CFG3,
+ DP83TG720S_LPS_CFG3_PWR_MODE_0);
+ if (ret)
+ return ret;
+
+ return genphy_c45_pma_baset1_read_master_slave(phydev);
}
static struct phy_driver dp83tg720_driver[] = {
--
2.39.2
On Thu, Jun 13, 2024 at 08:30:34PM +0200, Oleksij Rempel wrote:
> Get initial master/slave configuration, otherwise ethtool
> wont be able to provide this information until link is
> established. This makes troubleshooting harder, since wrong
> role configuration would prevent the link start.
I looked at how genphy_c45_read_status() works. If we have
phydev->autoneg == AUTONEG_ENABLE then genphy_c45_baset1_read_status()
is called which sets phydev->master_slave_get. If not AUTONEG_ENABLE
it calls genphy_c45_read_pma() which ends up calling
genphy_c45_pma_baset1_read_master_slave().
So it seems like the .read_status op should be setting master/slave
each time it is called, and not one time during .config_init.
What do you think?
Andrew
On Thu, Jun 13, 2024 at 09:33:01PM +0200, Andrew Lunn wrote:
> On Thu, Jun 13, 2024 at 08:30:34PM +0200, Oleksij Rempel wrote:
> > Get initial master/slave configuration, otherwise ethtool
> > wont be able to provide this information until link is
> > established. This makes troubleshooting harder, since wrong
> > role configuration would prevent the link start.
>
> I looked at how genphy_c45_read_status() works. If we have
> phydev->autoneg == AUTONEG_ENABLE then genphy_c45_baset1_read_status()
> is called which sets phydev->master_slave_get. If not AUTONEG_ENABLE
> it calls genphy_c45_read_pma() which ends up calling
> genphy_c45_pma_baset1_read_master_slave().
>
> So it seems like the .read_status op should be setting master/slave
> each time it is called, and not one time during .config_init.
>
> What do you think?
Yes, you are right. I verified it:
In case of this driver, .config_init will be executed every time no link
is detected over phy_init_hw() call. If link is detected
genphy_c45_pma_baset1_read_master_slave() is called directly.
It is not directly visible but read_master_slave() will be executed on
every .read_status.
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
On Fri, Jun 14, 2024 at 07:21:15AM +0200, Oleksij Rempel wrote:
> On Thu, Jun 13, 2024 at 09:33:01PM +0200, Andrew Lunn wrote:
> > On Thu, Jun 13, 2024 at 08:30:34PM +0200, Oleksij Rempel wrote:
> > > Get initial master/slave configuration, otherwise ethtool
> > > wont be able to provide this information until link is
> > > established. This makes troubleshooting harder, since wrong
> > > role configuration would prevent the link start.
> >
> > I looked at how genphy_c45_read_status() works. If we have
> > phydev->autoneg == AUTONEG_ENABLE then genphy_c45_baset1_read_status()
> > is called which sets phydev->master_slave_get. If not AUTONEG_ENABLE
> > it calls genphy_c45_read_pma() which ends up calling
> > genphy_c45_pma_baset1_read_master_slave().
> >
> > So it seems like the .read_status op should be setting master/slave
> > each time it is called, and not one time during .config_init.
> >
> > What do you think?
>
> Yes, you are right. I verified it:
> In case of this driver, .config_init will be executed every time no link
> is detected over phy_init_hw() call. If link is detected
> genphy_c45_pma_baset1_read_master_slave() is called directly.
> It is not directly visible but read_master_slave() will be executed on
> every .read_status.
Hm.. on other hand. Since the configuration state is readed only on
init and reset, we will see on user space side only default state not updated
after config_aneg().
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |