This driver provides support for clock controller on Loongson-2 SoC,
the Loongson-2 SoC uses a 100MHz clock as the PLL reference clock,
there are five independent PLLs inside, each of which PLL can
provide up to three sets of frequency dependent clock outputs.
Signed-off-by: Yinbo Zhu <[email protected]>
---
Change in v15:
1. Remove the depends on COMMON_CLK && OF and add depend on
LOONGARCH || COMPILE_TEST.
2. Remove some head file that include "linux/of.h", "linux/of_address.h"
and "linux/clk.h".
3. Remove the initialization of .name in struct clk_parent_data.
4. Replace device node with struct device.
5. Replace of_clk_hw_register with devm_clk_hw_register.
6. Remove the initialized operaion in loongson2_calc_pll_rate.
7. Inline the function about loongson2_clocks_init.
8. Replace of_iomap with devm_platform_ioremap_resource.
9. Drop error messages when mapping.
10. Replace kzalloc with devm_kzalloc.
Change in v14:
1. For some board's config file doesn't enable CONFIG_64BIT and
will report readq undefine error, and this version was to
add include <linux/io-64-nonatomic-lo-hi.h> to fix this issue.
Change in v13:
1. Add the Loongson-2 boot clk support.
Change in v12:
1. Change driver register way that use platform driver register.
Change in v11:
1. Remove the repetitive COMMON_CLK config in loongarch Kconfig.
2. Fixup the help paragraph descprition in COMMON_CLK_LOONGSON2.
3. Drop the <linux/clkdev.h>.
4. Drop the cast in clock driver.
5. Use div_u64() replace do_div().
6. Inline this function for loongson2_check_clk_hws.
7. Fixup the comma deposition on the loongson2_check_clk_hws.
8. Drop the loongson2_obtain_fixed_clk_hw and rework this driver
use clk_parent_data and the 'fw_name'.
Change in v10:
1. Detach of_clk_init to another patch.
Change in v9:
1. Add all history changelog information.
Change in v8:
1. Remove the flag "CLK_IS_BASIC".
Change in v7:
1. Adjust position alphabetically in Kconfig and Makefile.
2. Add static for loongson2_pll_base.
3. Move other file-scope variables in probe.
Change in v6:
1. NO change, but other patch in this series of patches has
changes.
Change in v5:
1. Replace loongson2 with Loongson-2 in commit info.
2. Replace Loongson2 with Loongson-2 in binding and
Kconfig file.
3. Replace soc with SoC.
Change in v4:
1. Fixup clock-names that replace "xxx-clk" with "xxx".
Change in v3:
1. NO change, but other patch in this series of patches has
changes.
Change in v2:
1. Update the include filename.
2. Change string from refclk/REFCLK to ref/REF.
MAINTAINERS | 1 +
drivers/clk/Kconfig | 9 +
drivers/clk/Makefile | 1 +
drivers/clk/clk-loongson2.c | 344 ++++++++++++++++++++++++++++++++++++
4 files changed, 355 insertions(+)
create mode 100644 drivers/clk/clk-loongson2.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 25a0981c74b6..a6983bf85956 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12155,6 +12155,7 @@ M: Yinbo Zhu <[email protected]>
L: [email protected]
S: Maintained
F: Documentation/devicetree/bindings/clock/loongson,ls2k-clk.yaml
+F: drivers/clk/clk-loongson2.c
F: include/dt-bindings/clock/loongson,ls2k-clk.h
LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 1eef05bb1f99..6da372fcc56a 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -325,6 +325,15 @@ config COMMON_CLK_LOCHNAGAR
This driver supports the clocking features of the Cirrus Logic
Lochnagar audio development board.
+config COMMON_CLK_LOONGSON2
+ bool "Clock driver for Loongson-2 SoC"
+ depends on LOONGARCH || COMPILE_TEST
+ help
+ This driver provides support for clock controller on Loongson-2 SoC.
+ The clock controller can generates and supplies clock to various
+ peripherals within the SoC.
+ Say Y here to support Loongson-2 SoC clock driver.
+
config COMMON_CLK_NXP
def_bool COMMON_CLK && (ARCH_LPC18XX || ARCH_LPC32XX)
select REGMAP_MMIO if ARCH_LPC32XX
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index e3ca0d058a25..b298c5dabc1a 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_COMMON_CLK_K210) += clk-k210.o
obj-$(CONFIG_LMK04832) += clk-lmk04832.o
obj-$(CONFIG_COMMON_CLK_LAN966X) += clk-lan966x.o
obj-$(CONFIG_COMMON_CLK_LOCHNAGAR) += clk-lochnagar.o
+obj-$(CONFIG_COMMON_CLK_LOONGSON2) += clk-loongson2.o
obj-$(CONFIG_COMMON_CLK_MAX77686) += clk-max77686.o
obj-$(CONFIG_COMMON_CLK_MAX9485) += clk-max9485.o
obj-$(CONFIG_ARCH_MILBEAUT_M10V) += clk-milbeaut.o
diff --git a/drivers/clk/clk-loongson2.c b/drivers/clk/clk-loongson2.c
new file mode 100644
index 000000000000..090810655511
--- /dev/null
+++ b/drivers/clk/clk-loongson2.c
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Author: Yinbo Zhu <[email protected]>
+ * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/clk-provider.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
+#include <dt-bindings/clock/loongson,ls2k-clk.h>
+
+#define LOONGSON2_PLL_MULT_SHIFT 32
+#define LOONGSON2_PLL_MULT_WIDTH 10
+#define LOONGSON2_PLL_DIV_SHIFT 26
+#define LOONGSON2_PLL_DIV_WIDTH 6
+#define LOONGSON2_APB_FREQSCALE_SHIFT 20
+#define LOONGSON2_APB_FREQSCALE_WIDTH 3
+#define LOONGSON2_USB_FREQSCALE_SHIFT 16
+#define LOONGSON2_USB_FREQSCALE_WIDTH 3
+#define LOONGSON2_SATA_FREQSCALE_SHIFT 12
+#define LOONGSON2_SATA_FREQSCALE_WIDTH 3
+#define LOONGSON2_BOOT_FREQSCALE_SHIFT 8
+#define LOONGSON2_BOOT_FREQSCALE_WIDTH 3
+
+static void __iomem *loongson2_pll_base;
+
+static const struct clk_parent_data pdata[] = {
+ { .fw_name = "ref_100m",},
+};
+
+static struct clk_hw *loongson2_clk_register(struct device *dev,
+ const char *name,
+ const char *parent_name,
+ const struct clk_ops *ops,
+ unsigned long flags)
+{
+ int ret;
+ struct clk_hw *hw;
+ struct clk_init_data init;
+
+ /* allocate the divider */
+ hw = devm_kzalloc(dev, sizeof(*hw), GFP_KERNEL);
+ if (!hw)
+ return ERR_PTR(-ENOMEM);
+
+ init.name = name;
+ init.ops = ops;
+ init.flags = flags;
+ init.num_parents = 1;
+
+ if (!parent_name)
+ init.parent_data = pdata;
+ else
+ init.parent_names = &parent_name;
+
+ hw->init = &init;
+
+ /* register the clock */
+ ret = devm_clk_hw_register(dev, hw);
+ if (ret)
+ hw = ERR_PTR(ret);
+
+ return hw;
+}
+
+static unsigned long loongson2_calc_pll_rate(int offset, unsigned long rate)
+{
+ u64 val;
+ u32 mult, div;
+
+ val = readq(loongson2_pll_base + offset);
+
+ mult = (val >> LOONGSON2_PLL_MULT_SHIFT) &
+ clk_div_mask(LOONGSON2_PLL_MULT_WIDTH);
+ div = (val >> LOONGSON2_PLL_DIV_SHIFT) &
+ clk_div_mask(LOONGSON2_PLL_DIV_WIDTH);
+
+ return div_u64((u64)rate * mult, div);
+}
+
+static unsigned long loongson2_node_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_pll_rate(0x0, parent_rate);
+}
+
+static const struct clk_ops loongson2_node_clk_ops = {
+ .recalc_rate = loongson2_node_recalc_rate,
+};
+
+static unsigned long loongson2_ddr_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_pll_rate(0x10, parent_rate);
+}
+
+static const struct clk_ops loongson2_ddr_clk_ops = {
+ .recalc_rate = loongson2_ddr_recalc_rate,
+};
+
+static unsigned long loongson2_dc_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_pll_rate(0x20, parent_rate);
+}
+
+static const struct clk_ops loongson2_dc_clk_ops = {
+ .recalc_rate = loongson2_dc_recalc_rate,
+};
+
+static unsigned long loongson2_pix0_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_pll_rate(0x30, parent_rate);
+}
+
+static const struct clk_ops loongson2_pix0_clk_ops = {
+ .recalc_rate = loongson2_pix0_recalc_rate,
+};
+
+static unsigned long loongson2_pix1_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_pll_rate(0x40, parent_rate);
+}
+
+static const struct clk_ops loongson2_pix1_clk_ops = {
+ .recalc_rate = loongson2_pix1_recalc_rate,
+};
+
+static unsigned long loongson2_calc_rate(unsigned long rate,
+ int shift, int width)
+{
+ u64 val;
+ u32 mult;
+
+ val = readq(loongson2_pll_base + 0x50);
+
+ mult = (val >> shift) & clk_div_mask(width);
+
+ return div_u64((u64)rate * (mult + 1), 8);
+}
+
+static unsigned long loongson2_boot_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_rate(parent_rate,
+ LOONGSON2_BOOT_FREQSCALE_SHIFT,
+ LOONGSON2_BOOT_FREQSCALE_WIDTH);
+}
+
+static const struct clk_ops loongson2_boot_clk_ops = {
+ .recalc_rate = loongson2_boot_recalc_rate,
+};
+
+static unsigned long loongson2_apb_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_rate(parent_rate,
+ LOONGSON2_APB_FREQSCALE_SHIFT,
+ LOONGSON2_APB_FREQSCALE_WIDTH);
+}
+
+static const struct clk_ops loongson2_apb_clk_ops = {
+ .recalc_rate = loongson2_apb_recalc_rate,
+};
+
+static unsigned long loongson2_usb_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_rate(parent_rate,
+ LOONGSON2_USB_FREQSCALE_SHIFT,
+ LOONGSON2_USB_FREQSCALE_WIDTH);
+}
+
+static const struct clk_ops loongson2_usb_clk_ops = {
+ .recalc_rate = loongson2_usb_recalc_rate,
+};
+
+static unsigned long loongson2_sata_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return loongson2_calc_rate(parent_rate,
+ LOONGSON2_SATA_FREQSCALE_SHIFT,
+ LOONGSON2_SATA_FREQSCALE_WIDTH);
+}
+
+static const struct clk_ops loongson2_sata_clk_ops = {
+ .recalc_rate = loongson2_sata_recalc_rate,
+};
+
+static inline void loongson2_check_clk_hws(struct clk_hw *clks[], unsigned int count)
+{
+ unsigned int i;
+
+ for (i = 0; i < count; i++)
+ if (IS_ERR(clks[i]))
+ pr_err("Loongson2 clk %u: register failed with %ld\n",
+ i, PTR_ERR(clks[i]));
+}
+
+static inline void loongson2_clocks_init(struct device *dev)
+{
+ struct clk_hw **hws;
+ struct clk_hw_onecell_data *clk_hw_data;
+ spinlock_t loongson2_clk_lock;
+
+ clk_hw_data = devm_kzalloc(dev, struct_size(clk_hw_data, hws, LOONGSON2_CLK_END),
+ GFP_KERNEL);
+ if (WARN_ON(!clk_hw_data))
+ return;
+
+ clk_hw_data->num = LOONGSON2_CLK_END;
+ hws = clk_hw_data->hws;
+
+ hws[LOONGSON2_NODE_PLL] = loongson2_clk_register(dev, "node_pll",
+ NULL,
+ &loongson2_node_clk_ops, 0);
+
+ hws[LOONGSON2_DDR_PLL] = loongson2_clk_register(dev, "ddr_pll",
+ NULL,
+ &loongson2_ddr_clk_ops, 0);
+
+ hws[LOONGSON2_DC_PLL] = loongson2_clk_register(dev, "dc_pll",
+ NULL,
+ &loongson2_dc_clk_ops, 0);
+
+ hws[LOONGSON2_PIX0_PLL] = loongson2_clk_register(dev, "pix0_pll",
+ NULL,
+ &loongson2_pix0_clk_ops, 0);
+
+ hws[LOONGSON2_PIX1_PLL] = loongson2_clk_register(dev, "pix1_pll",
+ NULL,
+ &loongson2_pix1_clk_ops, 0);
+
+ hws[LOONGSON2_BOOT_CLK] = loongson2_clk_register(dev, "boot",
+ NULL,
+ &loongson2_boot_clk_ops, 0);
+
+ hws[LOONGSON2_NODE_CLK] = clk_hw_register_divider(NULL, "node",
+ "node_pll", 0,
+ loongson2_pll_base + 0x8, 0,
+ 6, CLK_DIVIDER_ONE_BASED,
+ &loongson2_clk_lock);
+
+ /*
+ * The hda clk divisor in the upper 32bits and the clk-prodiver
+ * layer code doesn't support 64bit io operation thus a conversion
+ * is required that subtract shift by 32 and add 4byte to the hda
+ * address
+ */
+ hws[LOONGSON2_HDA_CLK] = clk_hw_register_divider(NULL, "hda",
+ "ddr_pll", 0,
+ loongson2_pll_base + 0x22, 12,
+ 7, CLK_DIVIDER_ONE_BASED,
+ &loongson2_clk_lock);
+
+ hws[LOONGSON2_GPU_CLK] = clk_hw_register_divider(NULL, "gpu",
+ "ddr_pll", 0,
+ loongson2_pll_base + 0x18, 22,
+ 6, CLK_DIVIDER_ONE_BASED,
+ &loongson2_clk_lock);
+
+ hws[LOONGSON2_DDR_CLK] = clk_hw_register_divider(NULL, "ddr",
+ "ddr_pll", 0,
+ loongson2_pll_base + 0x18, 0,
+ 6, CLK_DIVIDER_ONE_BASED,
+ &loongson2_clk_lock);
+
+ hws[LOONGSON2_GMAC_CLK] = clk_hw_register_divider(NULL, "gmac",
+ "dc_pll", 0,
+ loongson2_pll_base + 0x28, 22,
+ 6, CLK_DIVIDER_ONE_BASED,
+ &loongson2_clk_lock);
+
+ hws[LOONGSON2_DC_CLK] = clk_hw_register_divider(NULL, "dc",
+ "dc_pll", 0,
+ loongson2_pll_base + 0x28, 0,
+ 6, CLK_DIVIDER_ONE_BASED,
+ &loongson2_clk_lock);
+
+ hws[LOONGSON2_APB_CLK] = loongson2_clk_register(dev, "apb",
+ "gmac",
+ &loongson2_apb_clk_ops, 0);
+
+ hws[LOONGSON2_USB_CLK] = loongson2_clk_register(dev, "usb",
+ "gmac",
+ &loongson2_usb_clk_ops, 0);
+
+ hws[LOONGSON2_SATA_CLK] = loongson2_clk_register(dev, "sata",
+ "gmac",
+ &loongson2_sata_clk_ops, 0);
+
+ hws[LOONGSON2_PIX0_CLK] = clk_hw_register_divider(NULL, "pix0",
+ "pix0_pll", 0,
+ loongson2_pll_base + 0x38, 0, 6,
+ CLK_DIVIDER_ONE_BASED,
+ &loongson2_clk_lock);
+
+ hws[LOONGSON2_PIX1_CLK] = clk_hw_register_divider(NULL, "pix1",
+ "pix1_pll", 0,
+ loongson2_pll_base + 0x48, 0, 6,
+ CLK_DIVIDER_ONE_BASED,
+ &loongson2_clk_lock);
+
+ loongson2_check_clk_hws(hws, LOONGSON2_CLK_END);
+
+ devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clk_hw_data);
+}
+
+static const struct of_device_id loongson2_clk_match_table[] = {
+ { .compatible = "loongson,ls2k-clk" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, loongson2_clk_match_table);
+
+static int loongson2_clk_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+
+ loongson2_pll_base = devm_platform_ioremap_resource(pdev, 0);
+ if (!loongson2_pll_base)
+ return PTR_ERR(loongson2_pll_base);
+
+ loongson2_clocks_init(dev);
+
+ return 0;
+}
+
+static struct platform_driver loongson2_clk_driver = {
+ .probe = loongson2_clk_probe,
+ .driver = {
+ .name = "loongson2-clk",
+ .of_match_table = loongson2_clk_match_table,
+ },
+};
+module_platform_driver(loongson2_clk_driver);
+
+MODULE_DESCRIPTION("Loongson2 clock driver");
+MODULE_LICENSE("GPL");
--
2.20.1
Quoting Yinbo Zhu (2023-03-21 06:07:10)
> diff --git a/drivers/clk/clk-loongson2.c b/drivers/clk/clk-loongson2.c
> new file mode 100644
> index 000000000000..090810655511
> --- /dev/null
> +++ b/drivers/clk/clk-loongson2.c
> @@ -0,0 +1,344 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Author: Yinbo Zhu <[email protected]>
> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
> + */
> +
> +#include <linux/err.h>
> +#include <linux/init.h>
> +#include <linux/clk-provider.h>
> +#include <linux/slab.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/io-64-nonatomic-lo-hi.h>
> +#include <dt-bindings/clock/loongson,ls2k-clk.h>
> +
> +#define LOONGSON2_PLL_MULT_SHIFT 32
> +#define LOONGSON2_PLL_MULT_WIDTH 10
> +#define LOONGSON2_PLL_DIV_SHIFT 26
> +#define LOONGSON2_PLL_DIV_WIDTH 6
> +#define LOONGSON2_APB_FREQSCALE_SHIFT 20
> +#define LOONGSON2_APB_FREQSCALE_WIDTH 3
> +#define LOONGSON2_USB_FREQSCALE_SHIFT 16
> +#define LOONGSON2_USB_FREQSCALE_WIDTH 3
> +#define LOONGSON2_SATA_FREQSCALE_SHIFT 12
> +#define LOONGSON2_SATA_FREQSCALE_WIDTH 3
> +#define LOONGSON2_BOOT_FREQSCALE_SHIFT 8
> +#define LOONGSON2_BOOT_FREQSCALE_WIDTH 3
> +
> +static void __iomem *loongson2_pll_base;
Why is this a global?
> +
> +static const struct clk_parent_data pdata[] = {
> + { .fw_name = "ref_100m",},
> +};
> +
> +static struct clk_hw *loongson2_clk_register(struct device *dev,
> + const char *name,
> + const char *parent_name,
> + const struct clk_ops *ops,
> + unsigned long flags)
> +{
> + int ret;
> + struct clk_hw *hw;
> + struct clk_init_data init;
> +
> + /* allocate the divider */
Remove useless comment.
> + hw = devm_kzalloc(dev, sizeof(*hw), GFP_KERNEL);
> + if (!hw)
> + return ERR_PTR(-ENOMEM);
> +
> + init.name = name;
> + init.ops = ops;
> + init.flags = flags;
> + init.num_parents = 1;
> +
> + if (!parent_name)
> + init.parent_data = pdata;
> + else
> + init.parent_names = &parent_name;
> +
> + hw->init = &init;
> +
> + /* register the clock */
Remove useless comment.
> + ret = devm_clk_hw_register(dev, hw);
> + if (ret)
> + hw = ERR_PTR(ret);
> +
> + return hw;
> +}
> +
[....]
> +
> +static const struct clk_ops loongson2_sata_clk_ops = {
> + .recalc_rate = loongson2_sata_recalc_rate,
> +};
> +
> +static inline void loongson2_check_clk_hws(struct clk_hw *clks[], unsigned int count)
This needs to return an error instead of be void.
> +{
> + unsigned int i;
> +
> + for (i = 0; i < count; i++)
> + if (IS_ERR(clks[i]))
> + pr_err("Loongson2 clk %u: register failed with %ld\n",
> + i, PTR_ERR(clks[i]));
> +}
> +
> +static inline void loongson2_clocks_init(struct device *dev)
> +{
> + struct clk_hw **hws;
> + struct clk_hw_onecell_data *clk_hw_data;
> + spinlock_t loongson2_clk_lock;
> +
> + clk_hw_data = devm_kzalloc(dev, struct_size(clk_hw_data, hws, LOONGSON2_CLK_END),
> + GFP_KERNEL);
> + if (WARN_ON(!clk_hw_data))
> + return;
> +
> + clk_hw_data->num = LOONGSON2_CLK_END;
> + hws = clk_hw_data->hws;
> +
> + hws[LOONGSON2_NODE_PLL] = loongson2_clk_register(dev, "node_pll",
> + NULL,
> + &loongson2_node_clk_ops, 0);
> +
> + hws[LOONGSON2_DDR_PLL] = loongson2_clk_register(dev, "ddr_pll",
> + NULL,
> + &loongson2_ddr_clk_ops, 0);
> +
> + hws[LOONGSON2_DC_PLL] = loongson2_clk_register(dev, "dc_pll",
> + NULL,
> + &loongson2_dc_clk_ops, 0);
> +
> + hws[LOONGSON2_PIX0_PLL] = loongson2_clk_register(dev, "pix0_pll",
> + NULL,
> + &loongson2_pix0_clk_ops, 0);
> +
> + hws[LOONGSON2_PIX1_PLL] = loongson2_clk_register(dev, "pix1_pll",
> + NULL,
> + &loongson2_pix1_clk_ops, 0);
> +
> + hws[LOONGSON2_BOOT_CLK] = loongson2_clk_register(dev, "boot",
> + NULL,
> + &loongson2_boot_clk_ops, 0);
> +
> + hws[LOONGSON2_NODE_CLK] = clk_hw_register_divider(NULL, "node",
These should be devm_ variants so they're undone on failure.
> + "node_pll", 0,
> + loongson2_pll_base + 0x8, 0,
> + 6, CLK_DIVIDER_ONE_BASED,
> + &loongson2_clk_lock);
> +
> + /*
> + * The hda clk divisor in the upper 32bits and the clk-prodiver
> + * layer code doesn't support 64bit io operation thus a conversion
> + * is required that subtract shift by 32 and add 4byte to the hda
> + * address
> + */
> + hws[LOONGSON2_HDA_CLK] = clk_hw_register_divider(NULL, "hda",
> + "ddr_pll", 0,
> + loongson2_pll_base + 0x22, 12,
> + 7, CLK_DIVIDER_ONE_BASED,
> + &loongson2_clk_lock);
> +
> + hws[LOONGSON2_GPU_CLK] = clk_hw_register_divider(NULL, "gpu",
> + "ddr_pll", 0,
> + loongson2_pll_base + 0x18, 22,
> + 6, CLK_DIVIDER_ONE_BASED,
> + &loongson2_clk_lock);
> +
> + hws[LOONGSON2_DDR_CLK] = clk_hw_register_divider(NULL, "ddr",
> + "ddr_pll", 0,
> + loongson2_pll_base + 0x18, 0,
> + 6, CLK_DIVIDER_ONE_BASED,
> + &loongson2_clk_lock);
> +
> + hws[LOONGSON2_GMAC_CLK] = clk_hw_register_divider(NULL, "gmac",
> + "dc_pll", 0,
> + loongson2_pll_base + 0x28, 22,
> + 6, CLK_DIVIDER_ONE_BASED,
> + &loongson2_clk_lock);
> +
> + hws[LOONGSON2_DC_CLK] = clk_hw_register_divider(NULL, "dc",
> + "dc_pll", 0,
> + loongson2_pll_base + 0x28, 0,
> + 6, CLK_DIVIDER_ONE_BASED,
> + &loongson2_clk_lock);
> +
> + hws[LOONGSON2_APB_CLK] = loongson2_clk_register(dev, "apb",
> + "gmac",
> + &loongson2_apb_clk_ops, 0);
> +
> + hws[LOONGSON2_USB_CLK] = loongson2_clk_register(dev, "usb",
> + "gmac",
> + &loongson2_usb_clk_ops, 0);
> +
> + hws[LOONGSON2_SATA_CLK] = loongson2_clk_register(dev, "sata",
> + "gmac",
> + &loongson2_sata_clk_ops, 0);
> +
> + hws[LOONGSON2_PIX0_CLK] = clk_hw_register_divider(NULL, "pix0",
> + "pix0_pll", 0,
> + loongson2_pll_base + 0x38, 0, 6,
> + CLK_DIVIDER_ONE_BASED,
> + &loongson2_clk_lock);
> +
> + hws[LOONGSON2_PIX1_CLK] = clk_hw_register_divider(NULL, "pix1",
> + "pix1_pll", 0,
> + loongson2_pll_base + 0x48, 0, 6,
> + CLK_DIVIDER_ONE_BASED,
> + &loongson2_clk_lock);
> +
> + loongson2_check_clk_hws(hws, LOONGSON2_CLK_END);
> +
> + devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clk_hw_data);
Return this error code.
> +}
> +
> +static const struct of_device_id loongson2_clk_match_table[] = {
> + { .compatible = "loongson,ls2k-clk" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, loongson2_clk_match_table);
This table can go next to the driver instead of be above probe.
> +
> +static int loongson2_clk_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> +
> + loongson2_pll_base = devm_platform_ioremap_resource(pdev, 0);
> + if (!loongson2_pll_base)
Should be IS_ERR(loongson2_pll_base)
> + return PTR_ERR(loongson2_pll_base);
> +
> + loongson2_clocks_init(dev);
Please inline this function here.
在 2023/3/22 上午7:42, Stephen Boyd 写道:
> Quoting Yinbo Zhu (2023-03-21 06:07:10)
>> diff --git a/drivers/clk/clk-loongson2.c b/drivers/clk/clk-loongson2.c
>> new file mode 100644
>> index 000000000000..090810655511
>> --- /dev/null
>> +++ b/drivers/clk/clk-loongson2.c
>> @@ -0,0 +1,344 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Author: Yinbo Zhu <[email protected]>
>> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
>> + */
>> +
>> +#include <linux/err.h>
>> +#include <linux/init.h>
>> +#include <linux/clk-provider.h>
>> +#include <linux/slab.h>
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/io-64-nonatomic-lo-hi.h>
>> +#include <dt-bindings/clock/loongson,ls2k-clk.h>
>> +
>> +#define LOONGSON2_PLL_MULT_SHIFT 32
>> +#define LOONGSON2_PLL_MULT_WIDTH 10
>> +#define LOONGSON2_PLL_DIV_SHIFT 26
>> +#define LOONGSON2_PLL_DIV_WIDTH 6
>> +#define LOONGSON2_APB_FREQSCALE_SHIFT 20
>> +#define LOONGSON2_APB_FREQSCALE_WIDTH 3
>> +#define LOONGSON2_USB_FREQSCALE_SHIFT 16
>> +#define LOONGSON2_USB_FREQSCALE_WIDTH 3
>> +#define LOONGSON2_SATA_FREQSCALE_SHIFT 12
>> +#define LOONGSON2_SATA_FREQSCALE_WIDTH 3
>> +#define LOONGSON2_BOOT_FREQSCALE_SHIFT 8
>> +#define LOONGSON2_BOOT_FREQSCALE_WIDTH 3
>> +
>> +static void __iomem *loongson2_pll_base;
> Why is this a global?
Normally, this should be an element in the structure, but since there is
only one
element, It is directly defined as a global variable for use by other
function.
>
>> +
>> +static const struct clk_parent_data pdata[] = {
>> + { .fw_name = "ref_100m",},
>> +};
>> +
>> +static struct clk_hw *loongson2_clk_register(struct device *dev,
>> + const char *name,
>> + const char *parent_name,
>> + const struct clk_ops *ops,
>> + unsigned long flags)
>> +{
>> + int ret;
>> + struct clk_hw *hw;
>> + struct clk_init_data init;
>> +
>> + /* allocate the divider */
> Remove useless comment.
okay , I will remove it.
>
>> + hw = devm_kzalloc(dev, sizeof(*hw), GFP_KERNEL);
>> + if (!hw)
>> + return ERR_PTR(-ENOMEM);
>> +
>> + init.name = name;
>> + init.ops = ops;
>> + init.flags = flags;
>> + init.num_parents = 1;
>> +
>> + if (!parent_name)
>> + init.parent_data = pdata;
>> + else
>> + init.parent_names = &parent_name;
>> +
>> + hw->init = &init;
>> +
>> + /* register the clock */
> Remove useless comment.
okay, I will remove it.
>
>> + ret = devm_clk_hw_register(dev, hw);
>> + if (ret)
>> + hw = ERR_PTR(ret);
>> +
>> + return hw;
>> +}
>> +
> [....]
>> +
>> +static const struct clk_ops loongson2_sata_clk_ops = {
>> + .recalc_rate = loongson2_sata_recalc_rate,
>> +};
>> +
>> +static inline void loongson2_check_clk_hws(struct clk_hw *clks[], unsigned int count)
> This needs to return an error instead of be void.
okay, I got it.
>
>> +{
>> + unsigned int i;
>> +
>> + for (i = 0; i < count; i++)
>> + if (IS_ERR(clks[i]))
>> + pr_err("Loongson2 clk %u: register failed with %ld\n",
>> + i, PTR_ERR(clks[i]));
>> +}
>> +
>> +static inline void loongson2_clocks_init(struct device *dev)
>> +{
>> + struct clk_hw **hws;
>> + struct clk_hw_onecell_data *clk_hw_data;
>> + spinlock_t loongson2_clk_lock;
>> +
>> + clk_hw_data = devm_kzalloc(dev, struct_size(clk_hw_data, hws, LOONGSON2_CLK_END),
>> + GFP_KERNEL);
>> + if (WARN_ON(!clk_hw_data))
>> + return;
>> +
>> + clk_hw_data->num = LOONGSON2_CLK_END;
>> + hws = clk_hw_data->hws;
>> +
>> + hws[LOONGSON2_NODE_PLL] = loongson2_clk_register(dev, "node_pll",
>> + NULL,
>> + &loongson2_node_clk_ops, 0);
>> +
>> + hws[LOONGSON2_DDR_PLL] = loongson2_clk_register(dev, "ddr_pll",
>> + NULL,
>> + &loongson2_ddr_clk_ops, 0);
>> +
>> + hws[LOONGSON2_DC_PLL] = loongson2_clk_register(dev, "dc_pll",
>> + NULL,
>> + &loongson2_dc_clk_ops, 0);
>> +
>> + hws[LOONGSON2_PIX0_PLL] = loongson2_clk_register(dev, "pix0_pll",
>> + NULL,
>> + &loongson2_pix0_clk_ops, 0);
>> +
>> + hws[LOONGSON2_PIX1_PLL] = loongson2_clk_register(dev, "pix1_pll",
>> + NULL,
>> + &loongson2_pix1_clk_ops, 0);
>> +
>> + hws[LOONGSON2_BOOT_CLK] = loongson2_clk_register(dev, "boot",
>> + NULL,
>> + &loongson2_boot_clk_ops, 0);
>> +
>> + hws[LOONGSON2_NODE_CLK] = clk_hw_register_divider(NULL, "node",
> These should be devm_ variants so they're undone on failure.
okay , I will use devm_clk_hw_register_divider
>
>> + "node_pll", 0,
>> + loongson2_pll_base + 0x8, 0,
>> + 6, CLK_DIVIDER_ONE_BASED,
>> + &loongson2_clk_lock);
>> +
>> + /*
>> + * The hda clk divisor in the upper 32bits and the clk-prodiver
>> + * layer code doesn't support 64bit io operation thus a conversion
>> + * is required that subtract shift by 32 and add 4byte to the hda
>> + * address
>> + */
>> + hws[LOONGSON2_HDA_CLK] = clk_hw_register_divider(NULL, "hda",
>> + "ddr_pll", 0,
>> + loongson2_pll_base + 0x22, 12,
>> + 7, CLK_DIVIDER_ONE_BASED,
>> + &loongson2_clk_lock);
>> +
>> + hws[LOONGSON2_GPU_CLK] = clk_hw_register_divider(NULL, "gpu",
>> + "ddr_pll", 0,
>> + loongson2_pll_base + 0x18, 22,
>> + 6, CLK_DIVIDER_ONE_BASED,
>> + &loongson2_clk_lock);
>> +
>> + hws[LOONGSON2_DDR_CLK] = clk_hw_register_divider(NULL, "ddr",
>> + "ddr_pll", 0,
>> + loongson2_pll_base + 0x18, 0,
>> + 6, CLK_DIVIDER_ONE_BASED,
>> + &loongson2_clk_lock);
>> +
>> + hws[LOONGSON2_GMAC_CLK] = clk_hw_register_divider(NULL, "gmac",
>> + "dc_pll", 0,
>> + loongson2_pll_base + 0x28, 22,
>> + 6, CLK_DIVIDER_ONE_BASED,
>> + &loongson2_clk_lock);
>> +
>> + hws[LOONGSON2_DC_CLK] = clk_hw_register_divider(NULL, "dc",
>> + "dc_pll", 0,
>> + loongson2_pll_base + 0x28, 0,
>> + 6, CLK_DIVIDER_ONE_BASED,
>> + &loongson2_clk_lock);
>> +
>> + hws[LOONGSON2_APB_CLK] = loongson2_clk_register(dev, "apb",
>> + "gmac",
>> + &loongson2_apb_clk_ops, 0);
>> +
>> + hws[LOONGSON2_USB_CLK] = loongson2_clk_register(dev, "usb",
>> + "gmac",
>> + &loongson2_usb_clk_ops, 0);
>> +
>> + hws[LOONGSON2_SATA_CLK] = loongson2_clk_register(dev, "sata",
>> + "gmac",
>> + &loongson2_sata_clk_ops, 0);
>> +
>> + hws[LOONGSON2_PIX0_CLK] = clk_hw_register_divider(NULL, "pix0",
>> + "pix0_pll", 0,
>> + loongson2_pll_base + 0x38, 0, 6,
>> + CLK_DIVIDER_ONE_BASED,
>> + &loongson2_clk_lock);
>> +
>> + hws[LOONGSON2_PIX1_CLK] = clk_hw_register_divider(NULL, "pix1",
>> + "pix1_pll", 0,
>> + loongson2_pll_base + 0x48, 0, 6,
>> + CLK_DIVIDER_ONE_BASED,
>> + &loongson2_clk_lock);
>> +
>> + loongson2_check_clk_hws(hws, LOONGSON2_CLK_END);
>> +
>> + devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clk_hw_data);
> Return this error code.
okay, I got it.
>
>> +}
>> +
>> +static const struct of_device_id loongson2_clk_match_table[] = {
>> + { .compatible = "loongson,ls2k-clk" },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(of, loongson2_clk_match_table);
> This table can go next to the driver instead of be above probe.
okay, I will move it above loongson2_clk_driver.
>
>> +
>> +static int loongson2_clk_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> +
>> + loongson2_pll_base = devm_platform_ioremap_resource(pdev, 0);
>> + if (!loongson2_pll_base)
> Should be IS_ERR(loongson2_pll_base)
okay, I got it.
>
>> + return PTR_ERR(loongson2_pll_base);
>> +
>> + loongson2_clocks_init(dev);
> Please inline this function here.
The loongson2_clocks_init had inline in this version, or do you mean something else ? Need to inline the probe?
Quoting zhuyinbo (2023-03-21 19:07:26)
>
> 在 2023/3/22 上午7:42, Stephen Boyd 写道:
> > Quoting Yinbo Zhu (2023-03-21 06:07:10)
> >> diff --git a/drivers/clk/clk-loongson2.c b/drivers/clk/clk-loongson2.c
> >> new file mode 100644
> >> index 000000000000..090810655511
> >> --- /dev/null
> >> +++ b/drivers/clk/clk-loongson2.c
> >> @@ -0,0 +1,344 @@
[....]
> >> +
> >> +static void __iomem *loongson2_pll_base;
> > Why is this a global?
>
> Normally, this should be an element in the structure, but since there is
> only one
>
> element, It is directly defined as a global variable for use by other
> function.
>
Ok. Globals are frowned upon but it's just a single pointers so I guess
it's Ok.
> >
> >> + return PTR_ERR(loongson2_pll_base);
> >> +
> >> + loongson2_clocks_init(dev);
> > Please inline this function here.
>
> The loongson2_clocks_init had inline in this version, or do you mean something else ? Need to inline the probe?
I mean get rid of the function loongson2_clocks_init() and move the code
in that function into this probe function. With this patch the probe is
split to two functions when it should be one function.
在 2023/3/22 下午11:16, Stephen Boyd 写道:
> Quoting zhuyinbo (2023-03-21 19:07:26)
>> 在 2023/3/22 上午7:42, Stephen Boyd 写道:
>>> Quoting Yinbo Zhu (2023-03-21 06:07:10)
>>>> diff --git a/drivers/clk/clk-loongson2.c b/drivers/clk/clk-loongson2.c
>>>> new file mode 100644
>>>> index 000000000000..090810655511
>>>> --- /dev/null
>>>> +++ b/drivers/clk/clk-loongson2.c
>>>> @@ -0,0 +1,344 @@
> [....]
>>>> +
>>>> +static void __iomem *loongson2_pll_base;
>>> Why is this a global?
>> Normally, this should be an element in the structure, but since there is
>> only one
>>
>> element, It is directly defined as a global variable for use by other
>> function.
>>
> Ok. Globals are frowned upon but it's just a single pointers so I guess
> it's Ok.
>
>>>> + return PTR_ERR(loongson2_pll_base);
>>>> +
>>>> + loongson2_clocks_init(dev);
>>> Please inline this function here.
>> The loongson2_clocks_init had inline in this version, or do you mean something else ? Need to inline the probe?
> I mean get rid of the function loongson2_clocks_init() and move the code
> in that function into this probe function. With this patch the probe is
> split to two functions when it should be one function.
okay, I got it.
Thanks.