Odroid N2/N2+ support active cooling via gpio-fan controller.
Add fan controls and tip point for cpu and ddr thermal sensor
on this boards.
Signed-off-by: Anand Moon <[email protected]>
---
.../dts/amlogic/meson-g12b-odroid-n2.dtsi | 42 +++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index fd3fa82e4c33..e61a4285a910 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -39,6 +39,14 @@ emmc_pwrseq: emmc-pwrseq {
reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
};
+ fan: gpio-fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio_ao GPIOAO_10 GPIO_ACTIVE_HIGH>;
+ /* Using Dummy Speed */
+ gpio-fan,speed-map = <0 0>, <1 1>;
+ #cooling-cells = <2>;
+ };
+
leds {
compatible = "gpio-leds";
@@ -410,6 +418,40 @@ &cpu103 {
clock-latency = <50000>;
};
+&cpu_thermal {
+ trips {
+ cpu_active: cpu-active {
+ temperature = <60000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&cpu_active>;
+ cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&ddr_thermal {
+ trips {
+ ddr_active: cpu-active {
+ temperature = <60000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&ddr_active>;
+ cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
&ext_mdio {
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
base-commit: aae703b02f92bde9264366c545e87cec451de471
--
2.38.0
Hello Anand,
On Tue, Oct 18, 2022 at 9:53 PM Anand Moon <[email protected]> wrote:
>
> Odroid N2/N2+ support active cooling via gpio-fan controller.
> Add fan controls and tip point for cpu and ddr thermal sensor
> on this boards.
In the schematics for board rev 0.6 [0] I cannot find any information
about a fan connector.
The schematics for board rev 0.3 [1] on the other hand document a PWM
based fan connector on page 16.
So now I am not sure whether your patch only applies to certain board
revisions, the schematics are incorrect, etc.
Can you please provide some details about the fan connector on
Odroid-N2/N2+ and which hardware revisions are supported (and which
aren't) by your patch?
Thank you!
Martin
[0] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf
[1] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.3_20190117.pdf
Den 18.10.2022 kl. 23.16 skrev Martin Blumenstingl:
> Hello Anand,
>
> On Tue, Oct 18, 2022 at 9:53 PM Anand Moon <[email protected]> wrote:
>> Odroid N2/N2+ support active cooling via gpio-fan controller.
>> Add fan controls and tip point for cpu and ddr thermal sensor
>> on this boards.
> In the schematics for board rev 0.6 [0] I cannot find any information
> about a fan connector.
> The schematics for board rev 0.3 [1] on the other hand document a PWM
> based fan connector on page 16.
> So now I am not sure whether your patch only applies to certain board
> revisions, the schematics are incorrect, etc.
>
> Can you please provide some details about the fan connector on
> Odroid-N2/N2+ and which hardware revisions are supported (and which
> aren't) by your patch?
I can add that my N2+ rev 0.5 does have a fan connector.
>
>
> Thank you!
> Martin
>
>
> [0] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf
> [1] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.3_20190117.pdf
>
> _______________________________________________
> linux-amlogic mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-amlogic
--
Kind regards
*Dan Johansen*
Project lead of the *Manjaro ARM* project
Manjaro-ARM <https://manjaro.org>
Hi Martin,
On Wed, 19 Oct 2022 at 02:46, Martin Blumenstingl
<[email protected]> wrote:
>
> Hello Anand,
>
> On Tue, Oct 18, 2022 at 9:53 PM Anand Moon <[email protected]> wrote:
> >
> > Odroid N2/N2+ support active cooling via gpio-fan controller.
> > Add fan controls and tip point for cpu and ddr thermal sensor
> > on this boards.
> In the schematics for board rev 0.6 [0] I cannot find any information
> about a fan connector.
> The schematics for board rev 0.3 [1] on the other hand document a PWM
> based fan connector on page 16.
> So now I am not sure whether your patch only applies to certain board
> revisions, the schematics are incorrect, etc.
>
> Can you please provide some details about the fan connector on
> Odroid-N2/N2+ and which hardware revisions are supported (and which
> aren't) by your patch?
>
>
Ok I got this wrong the schematics below there is pwm controller, not
gpio controller
GPIOAO.BIT10 (PWM)
I will correct the patch sorry for the mistake I did not look more carefully.
> Thank you!
> Martin
>
>
> [0] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf
> [1] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.3_20190117.pdf
Thanks
-Anand
Hi,
On 18/10/2022 23:16, Martin Blumenstingl wrote:
> Hello Anand,
>
> On Tue, Oct 18, 2022 at 9:53 PM Anand Moon <[email protected]> wrote:
>>
>> Odroid N2/N2+ support active cooling via gpio-fan controller.
>> Add fan controls and tip point for cpu and ddr thermal sensor
>> on this boards.
> In the schematics for board rev 0.6 [0] I cannot find any information
> about a fan connector.
> The schematics for board rev 0.3 [1] on the other hand document a PWM
> based fan connector on page 16.
It seems the fan connector is on page 41 on rev 0.6 and it seems to be the same.
> So now I am not sure whether your patch only applies to certain board
> revisions, the schematics are incorrect, etc.
>
> Can you please provide some details about the fan connector on
> Odroid-N2/N2+ and which hardware revisions are supported (and which
> aren't) by your patch?
>
>
> Thank you!
> Martin
>
>
> [0] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf
> [1] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.3_20190117.pdf
Neil
Hi Martin,
On Wed, 19 Oct 2022 at 08:36, Anand Moon <[email protected]> wrote:
>
> Hi Martin,
>
> On Wed, 19 Oct 2022 at 02:46, Martin Blumenstingl
> <[email protected]> wrote:
> >
> > Hello Anand,
> >
> > On Tue, Oct 18, 2022 at 9:53 PM Anand Moon <[email protected]> wrote:
> > >
> > > Odroid N2/N2+ support active cooling via gpio-fan controller.
> > > Add fan controls and tip point for cpu and ddr thermal sensor
> > > on this boards.
> > In the schematics for board rev 0.6 [0] I cannot find any information
> > about a fan connector.
> > The schematics for board rev 0.3 [1] on the other hand document a PWM
> > based fan connector on page 16.
> > So now I am not sure whether your patch only applies to certain board
> > revisions, the schematics are incorrect, etc.
> >
> > Can you please provide some details about the fan connector on
> > Odroid-N2/N2+ and which hardware revisions are supported (and which
> > aren't) by your patch?
> >
> >
> Ok I got this wrong the schematics below there is pwm controller, not
> gpio controller
> GPIOAO.BIT10 (PWM)
> I will correct the patch sorry for the mistake I did not look more carefully.
>
As per the schematics GPIOAO_10 is controlled by PWMAO_D
But looking into the datasheet [0] I could not find the relevant
PWMAO_D pmw ip block to link the fan to the PWM controller.
[0] https://dn.odroid.com/S922X/ODROID-N2/Datasheet/S922X_Public_Datasheet_V0.2.pdf
I could get the PWM node but is not working for me.
@@ -547,6 +588,14 @@ &pwm_ab {
status = "okay";
};
+&pwm_AO_ab {
+ pinctrl-1 = <&pwm_ao_d_10_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
Thanks
-Anand
> > Thank you!
> > Martin
> >
> >
> > [0] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf
> > [1] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.3_20190117.pdf
> Thanks
> -Anand
Hi Anand,
On 19/10/2022 11:48, Anand Moon wrote:
> Hi Martin,
>
> On Wed, 19 Oct 2022 at 08:36, Anand Moon <[email protected]> wrote:
>>
>> Hi Martin,
>>
>> On Wed, 19 Oct 2022 at 02:46, Martin Blumenstingl
>> <[email protected]> wrote:
>>>
>>> Hello Anand,
>>>
>>> On Tue, Oct 18, 2022 at 9:53 PM Anand Moon <[email protected]> wrote:
>>>>
>>>> Odroid N2/N2+ support active cooling via gpio-fan controller.
>>>> Add fan controls and tip point for cpu and ddr thermal sensor
>>>> on this boards.
>>> In the schematics for board rev 0.6 [0] I cannot find any information
>>> about a fan connector.
>>> The schematics for board rev 0.3 [1] on the other hand document a PWM
>>> based fan connector on page 16.
>>> So now I am not sure whether your patch only applies to certain board
>>> revisions, the schematics are incorrect, etc.
>>>
>>> Can you please provide some details about the fan connector on
>>> Odroid-N2/N2+ and which hardware revisions are supported (and which
>>> aren't) by your patch?
>>>
>>>
>> Ok I got this wrong the schematics below there is pwm controller, not
>> gpio controller
>> GPIOAO.BIT10 (PWM)
>> I will correct the patch sorry for the mistake I did not look more carefully.
>>
>
> As per the schematics GPIOAO_10 is controlled by PWMAO_D
> But looking into the datasheet [0] I could not find the relevant
> PWMAO_D pmw ip block to link the fan to the PWM controller.
>
> [0] https://dn.odroid.com/S922X/ODROID-N2/Datasheet/S922X_Public_Datasheet_V0.2.pdf
>
> I could get the PWM node but is not working for me.
>
> @@ -547,6 +588,14 @@ &pwm_ab {
> status = "okay";
> };
>
> +&pwm_AO_ab {
&pwm_AO_cd not _ab
> + pinctrl-1 = <&pwm_ao_d_10_pins>;
> + pinctrl-names = "default";
> + clocks = <&xtal>;
> + clock-names = "clkin0";
> + status = "okay";
> +};
> +
>
> Thanks
> -Anand
>
>
>>> Thank you!
>>> Martin
>>>
>>>
>>> [0] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.6_20210121.pdf
>>> [1] https://dn.odroid.com/S922X/ODROID-N2/Schematic/odroid-n2_rev0.3_20190117.pdf
>> Thanks
>> -Anand
Neil
Am Dienstag, 18. Oktober 2022, 21:51:19 CEST schrieb Anand Moon:
> Odroid N2/N2+ support active cooling via gpio-fan controller.
> Add fan controls and tip point for cpu and ddr thermal sensor
> on this boards.
>
> Signed-off-by: Anand Moon <[email protected]>
> ---
> .../dts/amlogic/meson-g12b-odroid-n2.dtsi | 42 +++++++++++++++++++
> 1 file changed, 42 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi index
> fd3fa82e4c33..e61a4285a910 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
> @@ -39,6 +39,14 @@ emmc_pwrseq: emmc-pwrseq {
> reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
> };
>
> + fan: gpio-fan {
> + compatible = "gpio-fan";
> + gpios = <&gpio_ao GPIOAO_10 GPIO_ACTIVE_HIGH>;
> + /* Using Dummy Speed */
> + gpio-fan,speed-map = <0 0>, <1 1>;
> + #cooling-cells = <2>;
> + };
> +
> leds {
> compatible = "gpio-leds";
>
> @@ -410,6 +418,40 @@ &cpu103 {
> clock-latency = <50000>;
> };
>
> +&cpu_thermal {
> + trips {
> + cpu_active: cpu-active {
> + temperature = <60000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "active";
> + };
> + };
> +
> + cooling-maps {
> + map {
> + trip = <&cpu_active>;
> + cooling-device = <&fan THERMAL_NO_LIMIT
THERMAL_NO_LIMIT>;
> + };
> + };
> +};
> +
> +&ddr_thermal {
> + trips {
> + ddr_active: cpu-active {
I suspect this node name shall be 'ddr-active', not 'cpu-active'.
Best regards,
Alexander
> + temperature = <60000>; /* millicelsius */
> + hysteresis = <2000>; /* millicelsius */
> + type = "active";
> + };
> + };
> +
> + cooling-maps {
> + map {
> + trip = <&ddr_active>;
> + cooling-device = <&fan THERMAL_NO_LIMIT
THERMAL_NO_LIMIT>;
> + };
> + };
> +};
> +
> &ext_mdio {
> external_phy: ethernet-phy@0 {
> /* Realtek RTL8211F (0x001cc916) */
>
> base-commit: aae703b02f92bde9264366c545e87cec451de471
Hi Neil
On Wed, 19 Oct 2022 at 16:39, Neil Armstrong <[email protected]> wrote:
>
> Hi Anand,
>
> On 19/10/2022 11:48, Anand Moon wrote:
> > Hi Martin,
> >
> > On Wed, 19 Oct 2022 at 08:36, Anand Moon <[email protected]> wrote:
> >>
> >> Hi Martin,
> >>
> >> On Wed, 19 Oct 2022 at 02:46, Martin Blumenstingl
> >> <[email protected]> wrote:
> >>>
> >>> Hello Anand,
> >>>
> >>> On Tue, Oct 18, 2022 at 9:53 PM Anand Moon <[email protected]> wrote:
> >>>>
> >>>> Odroid N2/N2+ support active cooling via gpio-fan controller.
> >>>> Add fan controls and tip point for cpu and ddr thermal sensor
> >>>> on this boards.
> >>> In the schematics for board rev 0.6 [0] I cannot find any information
> >>> about a fan connector.
> >>> The schematics for board rev 0.3 [1] on the other hand document a PWM
> >>> based fan connector on page 16.
> >>> So now I am not sure whether your patch only applies to certain board
> >>> revisions, the schematics are incorrect, etc.
> >>>
> >>> Can you please provide some details about the fan connector on
> >>> Odroid-N2/N2+ and which hardware revisions are supported (and which
> >>> aren't) by your patch?
> >>>
> >>>
> >> Ok I got this wrong the schematics below there is pwm controller, not
> >> gpio controller
> >> GPIOAO.BIT10 (PWM)
> >> I will correct the patch sorry for the mistake I did not look more carefully.
> >>
> >
> > As per the schematics GPIOAO_10 is controlled by PWMAO_D
> > But looking into the datasheet [0] I could not find the relevant
> > PWMAO_D pmw ip block to link the fan to the PWM controller.
> >
> > [0] https://dn.odroid.com/S922X/ODROID-N2/Datasheet/S922X_Public_Datasheet_V0.2.pdf
> >
> > I could get the PWM node but is not working for me.
> >
> > @@ -547,6 +588,14 @@ &pwm_ab {
> > status = "okay";
> > };
> >
> > +&pwm_AO_ab {
>
> &pwm_AO_cd not _ab
>
No it has a conflict with CPU_B (vddcpu_b) PWM
I have tried linking all the PWM with pwm-fan but it's not working.
# sudo cat /sys/kernel/debug/pwm
platform/ffd1b000.pwm, 2 PWM devices
pwm-0 (regulator-vddcpu-a ): requested enabled period: 1250 ns
duty: 0 ns polarity: normal
pwm-1 ((null) ): period: 0 ns duty: 0 ns polarity: normal
platform/ff807000.pwm, 2 PWM devices
pwm-0 ((null) ): period: 0 ns duty: 0 ns polarity: normal
pwm-1 (pwm-fan ): requested period: 1250 ns duty: 0 ns
polarity: normal
platform/ff802000.pwm, 2 PWM devices
pwm-0 ((null) ): period: 0 ns duty: 0 ns polarity: normal
pwm-1 (regulator-vddcpu-b ): requested enabled period: 1250 ns
duty: 88 ns polarity: normal
Thanks
-Anand
Hi Anand,
On Wed, Oct 19, 2022 at 7:17 PM Anand Moon <[email protected]> wrote:
[...]
> > > +&pwm_AO_ab {
> >
> > &pwm_AO_cd not _ab
> >
> No it has a conflict with CPU_B (vddcpu_b) PWM
Uh, you're right. That's probably why the Hardkernel team uses a
software based PWM implementation: [0]
In hindsight they should have used a different pad either for VDDCPU_B
or the fan.
I think the most pragmatic approach (since the "GPIO PWM" driver is
not upstream and I don't know if something like that would be accepted
upstream) is to use a GPIO based fan as you did in your initial patch.
Not sure what others think though.
Best regards,
Martin
[0] https://github.com/hardkernel/linux/blob/c109dec94e7e819554830acfac4b6ed96e230179/arch/arm64/boot/dts/amlogic/meson64_odroidn2.dtsi#L356-L359
On 19/10/2022 22:40, Martin Blumenstingl wrote:
> Hi Anand,
>
> On Wed, Oct 19, 2022 at 7:17 PM Anand Moon <[email protected]> wrote:
> [...]
>>>> +&pwm_AO_ab {
>>>
>>> &pwm_AO_cd not _ab
>>>
>> No it has a conflict with CPU_B (vddcpu_b) PWM
> Uh, you're right. That's probably why the Hardkernel team uses a
> software based PWM implementation: [0]
> In hindsight they should have used a different pad either for VDDCPU_B
> or the fan.
>
> I think the most pragmatic approach (since the "GPIO PWM" driver is
> not upstream and I don't know if something like that would be accepted
> upstream) is to use a GPIO based fan as you did in your initial patch.
> Not sure what others think though.
>
Indeed I recall them using a SW pwm.
Yes it's perfectly ok to use a gpio-fan.
Anand, please fixup the ddr-active name and send a v2.
Thanks,
Neil
>
> Best regards,
> Martin
>
>
> [0] https://github.com/hardkernel/linux/blob/c109dec94e7e819554830acfac4b6ed96e230179/arch/arm64/boot/dts/amlogic/meson64_odroidn2.dtsi#L356-L359
Hi Martin / Neil,
On Thu, 20 Oct 2022 at 02:10, Martin Blumenstingl
<[email protected]> wrote:
>
> Hi Anand,
>
> On Wed, Oct 19, 2022 at 7:17 PM Anand Moon <[email protected]> wrote:
> [...]
> > > > +&pwm_AO_ab {
> > >
> > > &pwm_AO_cd not _ab
> > >
> > No it has a conflict with CPU_B (vddcpu_b) PWM
> Uh, you're right. That's probably why the Hardkernel team uses a
> software based PWM implementation: [0]
> In hindsight they should have used a different pad either for VDDCPU_B
> or the fan.
>
> I think the most pragmatic approach (since the "GPIO PWM" driver is
> not upstream and I don't know if something like that would be accepted
> upstream) is to use a GPIO based fan as you did in your initial patch.
> Not sure what others think though.
>
When I use gpio-fan I get the following output with gpioinfo
Feature it woks as expected.
$ .sudo gpioinfo
....
gpiochip1 - 15 lines:
line 0: unnamed unused input active-high
line 1: unnamed unused input active-high
line 2: unnamed "enable" output active-high [used]
line 3: unnamed unused input active-high
line 4: unnamed unused output active-high
line 5: unnamed unused input active-high
line 6: unnamed unused input active-high
line 7: unnamed unused input active-high
line 8: unnamed "regulator-tflash_vdd" output active-high [used]
line 9: unnamed "TF_IO" output active-high [used]
line 10: unnamed "gpio-fan" output active-high [used]
line 11: unnamed "n2:blue" output active-high [used]
line 12: unnamed unused input active-high
line 13: unnamed unused input active-high
line 14: unnamed unused input active-high
When I am using pwm-fan using *pwm_ao_d_10_pins* pin is not getting
registered below hence it is not working on my end.
$ .sudo gpioinfo
....
gpiochip1 - 15 lines:
line 0: unnamed unused input active-high
line 1: unnamed unused input active-high
line 2: unnamed "enable" output active-high [used]
line 3: unnamed unused input active-high
line 4: unnamed unused output active-high
line 5: unnamed unused input active-high
line 6: unnamed unused input active-high
line 7: unnamed unused input active-high
line 8: unnamed "regulator-tflash_vdd" output active-high [used]
line 9: unnamed "TF_IO" output active-high [used]
line 10: unnamed unused output active-high
line 11: unnamed "n2:blue" output active-high [used]
line 12: unnamed unused input active-high
line 13: unnamed unused input active-high
line 14: unnamed unused input active-high
Thanks
-Anand
>
> Best regards,
> Martin
>
>
> [0] https://github.com/hardkernel/linux/blob/c109dec94e7e819554830acfac4b6ed96e230179/arch/arm64/boot/dts/amlogic/meson64_odroidn2.dtsi#L356-L359
On 21/10/2022 07:07, Anand Moon wrote:
> Hi Martin / Neil,
>
> On Thu, 20 Oct 2022 at 02:10, Martin Blumenstingl
> <[email protected]> wrote:
>>
>> Hi Anand,
>>
>> On Wed, Oct 19, 2022 at 7:17 PM Anand Moon <[email protected]> wrote:
>> [...]
>>>>> +&pwm_AO_ab {
>>>>
>>>> &pwm_AO_cd not _ab
>>>>
>>> No it has a conflict with CPU_B (vddcpu_b) PWM
>> Uh, you're right. That's probably why the Hardkernel team uses a
>> software based PWM implementation: [0]
>> In hindsight they should have used a different pad either for VDDCPU_B
>> or the fan.
>>
>> I think the most pragmatic approach (since the "GPIO PWM" driver is
>> not upstream and I don't know if something like that would be accepted
>> upstream) is to use a GPIO based fan as you did in your initial patch.
>> Not sure what others think though.
>>
>
> When I use gpio-fan I get the following output with gpioinfo
> Feature it woks as expected.
>
> $ .sudo gpioinfo
> ....
> gpiochip1 - 15 lines:
> line 0: unnamed unused input active-high
> line 1: unnamed unused input active-high
> line 2: unnamed "enable" output active-high [used]
> line 3: unnamed unused input active-high
> line 4: unnamed unused output active-high
> line 5: unnamed unused input active-high
> line 6: unnamed unused input active-high
> line 7: unnamed unused input active-high
> line 8: unnamed "regulator-tflash_vdd" output active-high [used]
> line 9: unnamed "TF_IO" output active-high [used]
> line 10: unnamed "gpio-fan" output active-high [used]
> line 11: unnamed "n2:blue" output active-high [used]
> line 12: unnamed unused input active-high
> line 13: unnamed unused input active-high
> line 14: unnamed unused input active-high
>
> When I am using pwm-fan using *pwm_ao_d_10_pins* pin is not getting
> registered below hence it is not working on my end.
It's expected because it's not used as a GPIO but another function, you should look
in the pinctrl debugfs files to see it.
>
> $ .sudo gpioinfo
> ....
> gpiochip1 - 15 lines:
> line 0: unnamed unused input active-high
> line 1: unnamed unused input active-high
> line 2: unnamed "enable" output active-high [used]
> line 3: unnamed unused input active-high
> line 4: unnamed unused output active-high
> line 5: unnamed unused input active-high
> line 6: unnamed unused input active-high
> line 7: unnamed unused input active-high
> line 8: unnamed "regulator-tflash_vdd" output active-high [used]
> line 9: unnamed "TF_IO" output active-high [used]
> line 10: unnamed unused output active-high
> line 11: unnamed "n2:blue" output active-high [used]
> line 12: unnamed unused input active-high
> line 13: unnamed unused input active-high
> line 14: unnamed unused input active-high
>
> Thanks
> -Anand
>
>
>
>
>>
>> Best regards,
>> Martin
>>
>>
>> [0] https://github.com/hardkernel/linux/blob/c109dec94e7e819554830acfac4b6ed96e230179/arch/arm64/boot/dts/amlogic/meson64_odroidn2.dtsi#L356-L359