2023-12-01 05:05:21

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 00/10] Enable HS-G5 support on SM8550

This series enables HS-G5 support on SM8550.

This series is rebased on below changes from Mani -
https://patchwork.kernel.org/project/linux-scsi/patch/[email protected]/
https://patchwork.kernel.org/project/linux-scsi/patch/[email protected]/

This series is tested on below HW combinations -
SM8550 MTP + UFS4.0
SM8550 QRD + UFS3.1
SM8450 MTP + UFS3.1 (for regression test)
SM8350 MTP + UFS3.1 (for regression test)

Note that during reboot test on above platforms, I occasinally hit PA (PHY)
error during the 2nd init, this is not related with this series. A fix for
this is mentioned in below patchwork -

https://patchwork.kernel.org/project/linux-scsi/patch/[email protected]/

Also note that on platforms, which have two sets of UFS PHY settings are
provided (say G4 and no-G4, G5 and no-G5). The two sets of PHY settings are
basically programming different values to different registers, mixing the
two sets and/or overwriting one set with another set is definitely not
blessed by UFS PHY designers. For SM8550, this series will make sure we
honor the rule. However, for old targets Mani and I will fix them in
another series in future.

v6 -> v7:
1. Rebased on linux-next, based SM8650 PHY settings are merged there, no changes to patches for UFS driver
2. Addressed comments from Mani

v5 -> v6:
1. Rebased on scsi-queue-6.8
2. Addressed comments from Dmitry and Mani in patches to phy-qcom-qmp-ufs.c

v4 -> v5:
Removed two useless debug prints in patch #9

v3 -> v4:
Used .tbls_hs_overlay array instead of adding more tables with different names like .tbls_hs_g5

v2 -> v3:
1. Addressed comments from Andrew, Mani and Bart in patch #1
2. Added patch #2 as per request from Andrew and Mani
3. Added patch #4 to fix a common issue on old targets, it is not necessary
for this series, but put in this series only because it would be easier
to maintain and no need to rebase
4. Addressed comments from Dmitry and Mani in patches to phy-qcom-qmp-ufs.c

v1 -> v2:
1. Removed 2 changes which were exposing power info in sysfs
2. Removed 1 change which was moving data structs to phy-qcom-qmp-ufs.h
3. Added one new change (the 1st one) to clean up usage of ufs_dev_params based on comments from Mani
4. Adjusted the logic of UFS device version detection according to comments from Mani:
4.1 For HW version < 0x5, go through dual init
4.2 For HW version >= 0x5
a. If UFS device version is populated, one init is required
b. If UFS device version is not populated, go through dual init

Bao D. Nguyen (1):
scsi: ufs: ufs-qcom: Add support for UFS device version detection

Can Guo (9):
scsi: ufs: host: Rename structure ufs_dev_params to ufs_host_params
scsi: ufs: ufs-qcom: No need to set hs_rate after
ufshcd_init_host_param()
scsi: ufs: ufs-qcom: Setup host power mode during init
scsi: ufs: ufs-qcom: Allow the first init start with the maximum
supported gear
scsi: ufs: ufs-qcom: Limit HS-G5 Rate-A to hosts with HW version 5
scsi: ufs: ufs-qcom: Set initial PHY gear to max HS gear for HW ver 4
and newer
scsi: ufs: ufs-qcom: Check return value of phy_set_mode_ext()
phy: qualcomm: phy-qcom-qmp-ufs: Rectify SM8550 UFS HS-G4 PHY Settings
phy: qualcomm: phy-qcom-qmp-ufs: Add High Speed Gear 5 support for
SM8550

drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h | 2 +
drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h | 2 +
.../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 9 +
drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 191 ++++++++++++++++++---
drivers/ufs/host/ufs-exynos.c | 7 +-
drivers/ufs/host/ufs-hisi.c | 11 +-
drivers/ufs/host/ufs-mediatek.c | 12 +-
drivers/ufs/host/ufs-qcom.c | 97 ++++++++---
drivers/ufs/host/ufs-qcom.h | 7 +-
drivers/ufs/host/ufshcd-pltfrm.c | 69 ++++----
drivers/ufs/host/ufshcd-pltfrm.h | 10 +-
11 files changed, 309 insertions(+), 108 deletions(-)

--
2.7.4


2023-12-01 05:05:28

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 03/10] scsi: ufs: ufs-qcom: Setup host power mode during init

Setup host power mode and its limitations during UFS host driver init to
avoid repetitive work during every power mode change.

Acked-by: Andrew Halaney <[email protected]>
Reviewed-by: Nitin Rawat <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Co-developed-by: Bao D. Nguyen <[email protected]>
Signed-off-by: Bao D. Nguyen <[email protected]>
Signed-off-by: Can Guo <[email protected]>
---
drivers/ufs/host/ufs-qcom.c | 21 ++++++++++++++-------
drivers/ufs/host/ufs-qcom.h | 1 +
2 files changed, 15 insertions(+), 7 deletions(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index c21ff2c..9a90019 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -898,7 +898,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
struct ufs_pa_layer_attr *dev_req_params)
{
struct ufs_qcom_host *host = ufshcd_get_variant(hba);
- struct ufs_host_params host_params;
+ struct ufs_host_params *host_params = &host->host_params;
int ret = 0;

if (!dev_req_params) {
@@ -908,12 +908,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,

switch (status) {
case PRE_CHANGE:
- ufshcd_init_host_params(&host_params);
-
- /* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
- host_params.hs_tx_gear = host_params.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
-
- ret = ufshcd_negotiate_pwr_params(&host_params, dev_max_params, dev_req_params);
+ ret = ufshcd_negotiate_pwr_params(host_params, dev_max_params, dev_req_params);
if (ret) {
dev_err(hba->dev, "%s: failed to determine capabilities\n",
__func__);
@@ -1048,6 +1043,17 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
}

+static void ufs_qcom_set_host_params(struct ufs_hba *hba)
+{
+ struct ufs_qcom_host *host = ufshcd_get_variant(hba);
+ struct ufs_host_params *host_params = &host->host_params;
+
+ ufshcd_init_host_params(host_params);
+
+ /* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
+ host_params->hs_tx_gear = host_params->hs_rx_gear = ufs_qcom_get_hs_gear(hba);
+}
+
static void ufs_qcom_set_caps(struct ufs_hba *hba)
{
struct ufs_qcom_host *host = ufshcd_get_variant(hba);
@@ -1272,6 +1278,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)

ufs_qcom_set_caps(hba);
ufs_qcom_advertise_quirks(hba);
+ ufs_qcom_set_host_params(hba);

err = ufs_qcom_ice_init(host);
if (err)
diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
index 82cd143..11419eb 100644
--- a/drivers/ufs/host/ufs-qcom.h
+++ b/drivers/ufs/host/ufs-qcom.h
@@ -238,6 +238,7 @@ struct ufs_qcom_host {

struct gpio_desc *device_reset;

+ struct ufs_host_params host_params;
u32 phy_gear;

bool esi_enabled;
--
2.7.4

2023-12-01 05:05:30

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 05/10] scsi: ufs: ufs-qcom: Limit HS-G5 Rate-A to hosts with HW version 5

Qcom UFS hosts, with HW ver 5, can only support up to HS-G5 Rate-A due to
HW limitations. If the HS-G5 PHY gear is used, update host_params->hs_rate
to Rate-A, so that the subsequent power mode changes shall stick to Rate-A.

Reviewed-by: Nitin Rawat <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Can Guo <[email protected]>
---
drivers/ufs/host/ufs-qcom.c | 18 +++++++++++++++++-
1 file changed, 17 insertions(+), 1 deletion(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 81056b9..aca6199 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -442,9 +442,25 @@ static u32 ufs_qcom_get_hs_gear(struct ufs_hba *hba)
static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
{
struct ufs_qcom_host *host = ufshcd_get_variant(hba);
+ struct ufs_host_params *host_params = &host->host_params;
struct phy *phy = host->generic_phy;
+ enum phy_mode mode;
int ret;

+ /*
+ * HW ver 5 can only support up to HS-G5 Rate-A due to HW limitations.
+ * If the HS-G5 PHY gear is used, update host_params->hs_rate to Rate-A,
+ * so that the subsequent power mode change shall stick to Rate-A.
+ */
+ if (host->hw_ver.major == 0x5) {
+ if (host->phy_gear == UFS_HS_G5)
+ host_params->hs_rate = PA_HS_MODE_A;
+ else
+ host_params->hs_rate = PA_HS_MODE_B;
+ }
+
+ mode = host_params->hs_rate == PA_HS_MODE_B ? PHY_MODE_UFS_HS_B : PHY_MODE_UFS_HS_A;
+
/* Reset UFS Host Controller and PHY */
ret = ufs_qcom_host_reset(hba);
if (ret)
@@ -459,7 +475,7 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
return ret;
}

- phy_set_mode_ext(phy, PHY_MODE_UFS_HS_B, host->phy_gear);
+ phy_set_mode_ext(phy, mode, host->phy_gear);

/* power on phy - start serdes and phy's power and clocks */
ret = phy_power_on(phy);
--
2.7.4

2023-12-01 05:05:33

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 06/10] scsi: ufs: ufs-qcom: Set initial PHY gear to max HS gear for HW ver 4 and newer

Since HW ver 4, max HS gear can be get from UFS host controller's register,
use the max HS gear as the initial PHY gear instead of UFS_HS_G2, so that
we don't need to update the hard code for newer targets in future.

Reviewed-by: Nitin Rawat <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Can Guo <[email protected]>
---
drivers/ufs/host/ufs-qcom.c | 23 +++++++++++++++++------
1 file changed, 17 insertions(+), 6 deletions(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index aca6199..543939c 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -1060,6 +1060,22 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
}

+static void ufs_qcom_set_phy_gear(struct ufs_qcom_host *host)
+{
+ struct ufs_host_params *host_params = &host->host_params;
+
+ host->phy_gear = host_params->hs_tx_gear;
+
+ /*
+ * For controllers whose major HW version is < 4, power up the PHY using
+ * minimum supported gear (UFS_HS_G2). Switching to max gear will be
+ * performed during reinit if supported. For newer controllers, whose
+ * major HW version is >= 4, power up the PHY using max supported gear.
+ */
+ if (host->hw_ver.major < 0x4)
+ host->phy_gear = UFS_HS_G2;
+}
+
static void ufs_qcom_set_host_params(struct ufs_hba *hba)
{
struct ufs_qcom_host *host = ufshcd_get_variant(hba);
@@ -1296,6 +1312,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)
ufs_qcom_set_caps(hba);
ufs_qcom_advertise_quirks(hba);
ufs_qcom_set_host_params(hba);
+ ufs_qcom_set_phy_gear(host);

err = ufs_qcom_ice_init(host);
if (err)
@@ -1313,12 +1330,6 @@ static int ufs_qcom_init(struct ufs_hba *hba)
dev_warn(dev, "%s: failed to configure the testbus %d\n",
__func__, err);

- /*
- * Power up the PHY using the minimum supported gear (UFS_HS_G2).
- * Switching to max gear will be performed during reinit if supported.
- */
- host->phy_gear = UFS_HS_G2;
-
return 0;

out_variant_clear:
--
2.7.4

2023-12-01 05:05:35

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 04/10] scsi: ufs: ufs-qcom: Allow the first init start with the maximum supported gear

During host driver init, the phy_gear is set to the minimum supported gear
(HS_G2). Then, during the first power mode change, the negotiated gear, say
HS-G4, is updated to the phy_gear variable so that in the second init the
updated phy_gear can be used to program the PHY.

But the current code only allows update the phy_gear to a higher value. If
one wants to start the first init with the maximum support gear, say HS-G4,
the phy_gear is not updated to HS-G3 if the device only supports HS-G3.

The original check added there is intend to make sure the phy_gear won't be
updated when gear is scaled down (during clock scaling). Update the check
so that one can start the first init with the maximum support gear without
breaking the original fix by checking the ufshcd_state, that is, allow
update to phy_gear only if power mode change is invoked from
ufshcd_probe_hba().

Reviewed-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Can Guo <[email protected]>
---
drivers/ufs/host/ufs-qcom.c | 9 +++++----
1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 9a90019..81056b9 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -916,11 +916,12 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
}

/*
- * Update phy_gear only when the gears are scaled to a higher value. This is
- * because, the PHY gear settings are backwards compatible and we only need to
- * change the PHY gear settings while scaling to higher gears.
+ * During UFS driver probe, always update the PHY gear to match the negotiated
+ * gear, so that, if quirk UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH is enabled,
+ * the second init can program the optimal PHY settings. This allows one to start
+ * the first init with either the minimum or the maximum support gear.
*/
- if (dev_req_params->gear_tx > host->phy_gear)
+ if (hba->ufshcd_state == UFSHCD_STATE_RESET)
host->phy_gear = dev_req_params->gear_tx;

/* enable the device ref clock before changing to HS mode */
--
2.7.4

2023-12-01 05:05:41

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 09/10] phy: qualcomm: phy-qcom-qmp-ufs: Rectify SM8550 UFS HS-G4 PHY Settings

The registers, which are being touched in current SM8550 UFS PHY settings,
and the values being programmed are mainly the ones working for HS-G4 mode,
meanwhile, there are also a few ones somehow taken from HS-G5 PHY settings.
However, even consider HS-G4 mode only, some of them are incorrect and some
are missing. Rectify the HS-G4 PHY settings by strictly aligning with the
SM8550 UFS PHY Hardware Programming Guide suggested HS-G4 PHY settings.

Fixes: 1679bfef906f ("phy: qcom-qmp-ufs: Add SM8550 support")
Reviewed-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Abel Vesa <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Can Guo <[email protected]>
---
.../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 1 +
drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 28 +++++++++++++++-------
2 files changed, 20 insertions(+), 9 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
index ae220fd..35d497f 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
@@ -11,6 +11,7 @@
#define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX 0x30
#define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_RX 0x34
#define QSERDES_UFS_V6_TX_LANE_MODE_1 0x7c
+#define QSERDES_UFS_V6_TX_FR_DCC_CTRL 0x108

#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2 0x08
#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4 0x10
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
index 5f79d18..3c2e625 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
@@ -763,22 +763,26 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x4c),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x99),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x07),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x99),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
+};
+
+static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
};

static const struct qmp_phy_init_tbl sm8550_ufsphy_tx[] = {
- QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_LANE_MODE_1, 0x05),
QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_FR_DCC_CTRL, 0x4c),
};

static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
- QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2, 0x0c),
- QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2, 0x0c),
QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),

QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0, 0xc2),
@@ -801,6 +805,8 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_pcs[] = {
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x04),
+ QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x04),
};

static const struct qmp_phy_init_tbl sm8650_ufsphy_serdes[] = {
@@ -1357,6 +1363,10 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
.pcs = sm8550_ufsphy_pcs,
.pcs_num = ARRAY_SIZE(sm8550_ufsphy_pcs),
},
+ .tbls_hs_b = {
+ .serdes = sm8550_ufsphy_hs_b_serdes,
+ .serdes_num = ARRAY_SIZE(sm8550_ufsphy_hs_b_serdes),
+ },
.clk_list = sdm845_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
.vreg_list = qmp_phy_vreg_l,
--
2.7.4

2023-12-01 05:05:44

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 07/10] scsi: ufs: ufs-qcom: Check return value of phy_set_mode_ext()

In ufs_qcom_power_up_sequence(), check return value of phy_set_mode_ext()
and stop proceeding if phy_set_mode_ext() fails.

Reviewed-by: Nitin Rawat <[email protected]>
Signed-off-by: Can Guo <[email protected]>
---
drivers/ufs/host/ufs-qcom.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 543939c..ee3f07a 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -475,7 +475,9 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
return ret;
}

- phy_set_mode_ext(phy, mode, host->phy_gear);
+ ret = phy_set_mode_ext(phy, mode, host->phy_gear);
+ if (ret)
+ goto out_disable_phy;

/* power on phy - start serdes and phy's power and clocks */
ret = phy_power_on(phy);
--
2.7.4

2023-12-01 05:06:16

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 10/10] phy: qualcomm: phy-qcom-qmp-ufs: Add High Speed Gear 5 support for SM8550

On SM8550, two sets of UFS PHY settings are provided, one set is to support
HS-G5, another set is to support HS-G4 and lower gears. The two sets of PHY
settings are programming different values to different registers, mixing
the two sets and/or overwriting one set with another set is definitely not
blessed by UFS PHY designers.

To add HS-G5 support for SM8550, split the two sets of PHY settings into
their dedicated overlay tables, only the common parts of the two sets of
PHY settings are left in the .tbls.

Consider we are going to add even higher gear support in future, to avoid
adding more tables with different names, rename the .tbls_hs_g4 and make it
an array, a size of 2 is enough as of now.

In this case, .tbls alone is not a complete set of PHY settings, so either
tbls_hs_overlay[0] or tbls_hs_overlay[1] must be applied on top of the
.tbls to become a complete set of PHY settings.

Signed-off-by: Can Guo <[email protected]>
---
drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h | 2 +
drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h | 2 +
.../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 8 +
drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 169 ++++++++++++++++++---
4 files changed, 159 insertions(+), 22 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
index fe6c450..970cc06 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
@@ -19,6 +19,7 @@
#define QPHY_V6_PCS_UFS_BIST_FIXED_PAT_CTRL 0x060
#define QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY 0x074
#define QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY 0x0bc
+#define QPHY_V6_PCS_UFS_RX_HS_G5_SYNC_LENGTH_CAPABILITY 0x12c
#define QPHY_V6_PCS_UFS_DEBUG_BUS_CLKSEL 0x158
#define QPHY_V6_PCS_UFS_LINECFG_DISABLE 0x17c
#define QPHY_V6_PCS_UFS_RX_MIN_HIBERN8_TIME 0x184
@@ -28,5 +29,6 @@
#define QPHY_V6_PCS_UFS_READY_STATUS 0x1a8
#define QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1 0x1f4
#define QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1 0x1fc
+#define QPHY_V6_PCS_UFS_RX_HSG5_SYNC_WAIT_TIME 0x220

#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
index f420f8f..ef392ce 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
@@ -56,6 +56,8 @@
#define QSERDES_V6_COM_SYS_CLK_CTRL 0xe4
#define QSERDES_V6_COM_SYSCLK_BUF_ENABLE 0xe8
#define QSERDES_V6_COM_PLL_IVCO 0xf4
+#define QSERDES_V6_COM_CMN_IETRIM 0xfc
+#define QSERDES_V6_COM_CMN_IPTRIM 0x100
#define QSERDES_V6_COM_SYSCLK_EN_SEL 0x110
#define QSERDES_V6_COM_RESETSM_CNTRL 0x118
#define QSERDES_V6_COM_LOCK_CMP_EN 0x120
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
index 35d497f..d9a87bd 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
@@ -15,13 +15,19 @@

#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2 0x08
#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4 0x10
+#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_SO_GAIN_RATE4 0x24
#define QSERDES_UFS_V6_RX_UCDR_SO_SATURATION 0x28
+#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4 0x54
#define QSERDES_UFS_V6_RX_UCDR_PI_CTRL1 0x58
#define QSERDES_UFS_V6_RX_RX_TERM_BW_CTRL0 0xc4
#define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2 0xd4
#define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4 0xdc
+#define QSERDES_UFS_V6_RX_UCDR_SO_GAIN_RATE4 0xf0
+#define QSERDES_UFS_V6_RX_UCDR_PI_CONTROLS 0xf4
#define QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL 0x178
+#define QSERDES_UFS_V6_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x1bc
#define QSERDES_UFS_V6_RX_INTERFACE_MODE 0x1e0
+#define QSERDES_UFS_V6_RX_OFFSET_ADAPTOR_CNTRL3 0x1c4
#define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0 0x208
#define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1 0x20c
#define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B3 0x214
@@ -33,6 +39,8 @@
#define QSERDES_UFS_V6_RX_MODE_RATE3_B5 0x264
#define QSERDES_UFS_V6_RX_MODE_RATE3_B8 0x270
#define QSERDES_UFS_V6_RX_MODE_RATE4_B3 0x280
+#define QSERDES_UFS_V6_RX_MODE_RATE4_B4 0x284
#define QSERDES_UFS_V6_RX_MODE_RATE4_B6 0x28c
+#define QSERDES_UFS_V6_RX_DLL0_FTUNE_CTRL 0x2f8

#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
index 3c2e625..11cea34 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
@@ -41,6 +41,8 @@

#define PHY_INIT_COMPLETE_TIMEOUT 10000

+#define NUM_OVERLAY 2
+
struct qmp_phy_init_tbl {
unsigned int offset;
unsigned int val;
@@ -754,15 +756,22 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x11),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x01),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_INITVAL2, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
+};
+
+static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
+};
+
+static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_serdes[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x0a),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
@@ -771,19 +780,24 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
};

-static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
- QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
+static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_serdes[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IETRIM, 0x1b),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IPTRIM, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
};

static const struct qmp_phy_init_tbl sm8550_ufsphy_tx[] = {
QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_LANE_MODE_1, 0x05),
QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
+};
+
+static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_tx[] = {
QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_FR_DCC_CTRL, 0x4c),
};

static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2, 0x0c),
- QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),

QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0, 0xc2),
QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1, 0xc2),
@@ -799,16 +813,45 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE3_B8, 0x02),
};

+static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_rx[] = {
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),
+};
+
+static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_rx[] = {
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_SO_GAIN_RATE4, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_PI_CONTROLS, 0x07),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_OFFSET_ADAPTOR_CNTRL3, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_SO_GAIN_RATE4, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B3, 0xb9),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B4, 0x4f),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B6, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_DLL0_FTUNE_CTRL, 0x30),
+};
+
static const struct qmp_phy_init_tbl sm8550_ufsphy_pcs[] = {
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_SIGDET_CTRL2, 0x69),
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0f),
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
- QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_pcs[] = {
+ QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x04),
QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x04),
};

+static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_pcs[] = {
+ QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x33),
+ QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HS_G5_SYNC_LENGTH_CAPABILITY, 0x4f),
+ QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSG5_SYNC_WAIT_TIME, 0x9e),
+};
+
static const struct qmp_phy_init_tbl sm8650_ufsphy_serdes[] = {
QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
@@ -889,6 +932,8 @@ struct qmp_phy_cfg_tbls {
int rx_num;
const struct qmp_phy_init_tbl *pcs;
int pcs_num;
+ /* Maximum supported Gear of this tbls */
+ u32 max_gear;
};

/* struct qmp_phy_cfg - per-PHY initialization config */
@@ -896,13 +941,15 @@ struct qmp_phy_cfg {
int lanes;

const struct qmp_ufs_offsets *offsets;
+ /* Maximum supported Gear of this config */
+ u32 max_supported_gear;

/* Main init sequence for PHY blocks - serdes, tx, rx, pcs */
const struct qmp_phy_cfg_tbls tbls;
/* Additional sequence for HS Series B */
const struct qmp_phy_cfg_tbls tbls_hs_b;
- /* Additional sequence for HS G4 */
- const struct qmp_phy_cfg_tbls tbls_hs_g4;
+ /* Additional sequence for different HS Gears */
+ const struct qmp_phy_cfg_tbls tbls_hs_overlay[NUM_OVERLAY];

/* clock ids to be requested */
const char * const *clk_list;
@@ -1005,6 +1052,7 @@ static const struct qmp_phy_cfg msm8996_ufsphy_cfg = {
.lanes = 1,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G3,

.tbls = {
.serdes = msm8996_ufsphy_serdes,
@@ -1030,6 +1078,7 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G4,

.tbls = {
.serdes = sm8350_ufsphy_serdes,
@@ -1045,13 +1094,14 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = {
.serdes = sm8350_ufsphy_hs_b_serdes,
.serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
},
- .tbls_hs_g4 = {
+ .tbls_hs_overlay[0] = {
.tx = sm8350_ufsphy_g4_tx,
.tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
.rx = sm8350_ufsphy_g4_rx,
.rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
.pcs = sm8350_ufsphy_g4_pcs,
.pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
+ .max_gear = UFS_HS_G4,
},
.clk_list = sm8450_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
@@ -1064,6 +1114,7 @@ static const struct qmp_phy_cfg sc7280_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G4,

.tbls = {
.serdes = sm8150_ufsphy_serdes,
@@ -1079,13 +1130,14 @@ static const struct qmp_phy_cfg sc7280_ufsphy_cfg = {
.serdes = sm8150_ufsphy_hs_b_serdes,
.serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
},
- .tbls_hs_g4 = {
+ .tbls_hs_overlay[0] = {
.tx = sm8250_ufsphy_hs_g4_tx,
.tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx),
.rx = sc7280_ufsphy_hs_g4_rx,
.rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx),
.pcs = sm8150_ufsphy_hs_g4_pcs,
.pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
+ .max_gear = UFS_HS_G4,
},
.clk_list = sm8450_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
@@ -1098,6 +1150,7 @@ static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G4,

.tbls = {
.serdes = sm8350_ufsphy_serdes,
@@ -1113,13 +1166,14 @@ static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = {
.serdes = sm8350_ufsphy_hs_b_serdes,
.serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
},
- .tbls_hs_g4 = {
+ .tbls_hs_overlay[0] = {
.tx = sm8350_ufsphy_g4_tx,
.tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
.rx = sm8350_ufsphy_g4_rx,
.rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
.pcs = sm8350_ufsphy_g4_pcs,
.pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
+ .max_gear = UFS_HS_G4,
},
.clk_list = sdm845_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
@@ -1132,6 +1186,7 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G3,

.tbls = {
.serdes = sdm845_ufsphy_serdes,
@@ -1160,6 +1215,7 @@ static const struct qmp_phy_cfg sm6115_ufsphy_cfg = {
.lanes = 1,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G3,

.tbls = {
.serdes = sm6115_ufsphy_serdes,
@@ -1188,6 +1244,7 @@ static const struct qmp_phy_cfg sm7150_ufsphy_cfg = {
.lanes = 1,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G3,

.tbls = {
.serdes = sdm845_ufsphy_serdes,
@@ -1216,6 +1273,7 @@ static const struct qmp_phy_cfg sm8150_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G4,

.tbls = {
.serdes = sm8150_ufsphy_serdes,
@@ -1231,13 +1289,14 @@ static const struct qmp_phy_cfg sm8150_ufsphy_cfg = {
.serdes = sm8150_ufsphy_hs_b_serdes,
.serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
},
- .tbls_hs_g4 = {
+ .tbls_hs_overlay[0] = {
.tx = sm8150_ufsphy_hs_g4_tx,
.tx_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_tx),
.rx = sm8150_ufsphy_hs_g4_rx,
.rx_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_rx),
.pcs = sm8150_ufsphy_hs_g4_pcs,
.pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
+ .max_gear = UFS_HS_G4,
},
.clk_list = sdm845_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
@@ -1250,6 +1309,7 @@ static const struct qmp_phy_cfg sm8250_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G4,

.tbls = {
.serdes = sm8150_ufsphy_serdes,
@@ -1265,13 +1325,14 @@ static const struct qmp_phy_cfg sm8250_ufsphy_cfg = {
.serdes = sm8150_ufsphy_hs_b_serdes,
.serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
},
- .tbls_hs_g4 = {
+ .tbls_hs_overlay[0] = {
.tx = sm8250_ufsphy_hs_g4_tx,
.tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx),
.rx = sm8250_ufsphy_hs_g4_rx,
.rx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_rx),
.pcs = sm8150_ufsphy_hs_g4_pcs,
.pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
+ .max_gear = UFS_HS_G4,
},
.clk_list = sdm845_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
@@ -1284,6 +1345,7 @@ static const struct qmp_phy_cfg sm8350_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G4,

.tbls = {
.serdes = sm8350_ufsphy_serdes,
@@ -1299,13 +1361,14 @@ static const struct qmp_phy_cfg sm8350_ufsphy_cfg = {
.serdes = sm8350_ufsphy_hs_b_serdes,
.serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
},
- .tbls_hs_g4 = {
+ .tbls_hs_overlay[0] = {
.tx = sm8350_ufsphy_g4_tx,
.tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
.rx = sm8350_ufsphy_g4_rx,
.rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
.pcs = sm8350_ufsphy_g4_pcs,
.pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
+ .max_gear = UFS_HS_G4,
},
.clk_list = sdm845_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
@@ -1318,6 +1381,7 @@ static const struct qmp_phy_cfg sm8450_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets,
+ .max_supported_gear = UFS_HS_G4,

.tbls = {
.serdes = sm8350_ufsphy_serdes,
@@ -1333,13 +1397,14 @@ static const struct qmp_phy_cfg sm8450_ufsphy_cfg = {
.serdes = sm8350_ufsphy_hs_b_serdes,
.serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
},
- .tbls_hs_g4 = {
+ .tbls_hs_overlay[0] = {
.tx = sm8350_ufsphy_g4_tx,
.tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
.rx = sm8350_ufsphy_g4_rx,
.rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
.pcs = sm8350_ufsphy_g4_pcs,
.pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
+ .max_gear = UFS_HS_G4,
},
.clk_list = sm8450_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
@@ -1352,6 +1417,7 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets_v6,
+ .max_supported_gear = UFS_HS_G5,

.tbls = {
.serdes = sm8550_ufsphy_serdes,
@@ -1367,6 +1433,26 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
.serdes = sm8550_ufsphy_hs_b_serdes,
.serdes_num = ARRAY_SIZE(sm8550_ufsphy_hs_b_serdes),
},
+ .tbls_hs_overlay[0] = {
+ .serdes = sm8550_ufsphy_g4_serdes,
+ .serdes_num = ARRAY_SIZE(sm8550_ufsphy_g4_serdes),
+ .tx = sm8550_ufsphy_g4_tx,
+ .tx_num = ARRAY_SIZE(sm8550_ufsphy_g4_tx),
+ .rx = sm8550_ufsphy_g4_rx,
+ .rx_num = ARRAY_SIZE(sm8550_ufsphy_g4_rx),
+ .pcs = sm8550_ufsphy_g4_pcs,
+ .pcs_num = ARRAY_SIZE(sm8550_ufsphy_g4_pcs),
+ .max_gear = UFS_HS_G4,
+ },
+ .tbls_hs_overlay[1] = {
+ .serdes = sm8550_ufsphy_g5_serdes,
+ .serdes_num = ARRAY_SIZE(sm8550_ufsphy_g5_serdes),
+ .rx = sm8550_ufsphy_g5_rx,
+ .rx_num = ARRAY_SIZE(sm8550_ufsphy_g5_rx),
+ .pcs = sm8550_ufsphy_g5_pcs,
+ .pcs_num = ARRAY_SIZE(sm8550_ufsphy_g5_pcs),
+ .max_gear = UFS_HS_G5,
+ },
.clk_list = sdm845_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
.vreg_list = qmp_phy_vreg_l,
@@ -1378,6 +1464,7 @@ static const struct qmp_phy_cfg sm8650_ufsphy_cfg = {
.lanes = 2,

.offsets = &qmp_ufs_offsets_v6,
+ .max_supported_gear = UFS_HS_G5,

.tbls = {
.serdes = sm8650_ufsphy_serdes,
@@ -1451,17 +1538,49 @@ static void qmp_ufs_pcs_init(struct qmp_ufs *qmp, const struct qmp_phy_cfg_tbls
qmp_ufs_configure(pcs, tbls->pcs, tbls->pcs_num);
}

+static int qmp_ufs_get_gear_overlay(struct qmp_ufs *qmp, const struct qmp_phy_cfg *cfg)
+{
+ u32 max_gear, floor_max_gear = cfg->max_supported_gear;
+ int idx, ret = -EINVAL;
+
+ for (idx = NUM_OVERLAY - 1; idx >= 0; idx--) {
+ max_gear = cfg->tbls_hs_overlay[idx].max_gear;
+
+ /* Skip if the table is not available */
+ if (max_gear == 0)
+ continue;
+
+ /* Direct matching, bail */
+ if (qmp->submode == max_gear)
+ return idx;
+
+ /* If no direct matching, the lowest gear is the best matching */
+ if (max_gear < floor_max_gear) {
+ ret = idx;
+ floor_max_gear = max_gear;
+ }
+ }
+
+ return ret;
+}
+
static void qmp_ufs_init_registers(struct qmp_ufs *qmp, const struct qmp_phy_cfg *cfg)
{
+ int i;
+
qmp_ufs_serdes_init(qmp, &cfg->tbls);
- if (qmp->mode == PHY_MODE_UFS_HS_B)
- qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_b);
qmp_ufs_lanes_init(qmp, &cfg->tbls);
- if (qmp->submode == UFS_HS_G4)
- qmp_ufs_lanes_init(qmp, &cfg->tbls_hs_g4);
qmp_ufs_pcs_init(qmp, &cfg->tbls);
- if (qmp->submode == UFS_HS_G4)
- qmp_ufs_pcs_init(qmp, &cfg->tbls_hs_g4);
+
+ i = qmp_ufs_get_gear_overlay(qmp, cfg);
+ if (i >= 0) {
+ qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_overlay[i]);
+ qmp_ufs_lanes_init(qmp, &cfg->tbls_hs_overlay[i]);
+ qmp_ufs_pcs_init(qmp, &cfg->tbls_hs_overlay[i]);
+ }
+
+ if (qmp->mode == PHY_MODE_UFS_HS_B)
+ qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_b);
}

static int qmp_ufs_com_init(struct qmp_ufs *qmp)
@@ -1633,6 +1752,12 @@ static int qmp_ufs_disable(struct phy *phy)
static int qmp_ufs_set_mode(struct phy *phy, enum phy_mode mode, int submode)
{
struct qmp_ufs *qmp = phy_get_drvdata(phy);
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+
+ if (submode > cfg->max_supported_gear || submode == 0) {
+ dev_err(qmp->dev, "Invalid PHY submode %d\n", submode);
+ return -EINVAL;
+ }

qmp->mode = mode;
qmp->submode = submode;
--
2.7.4

2023-12-01 05:06:16

by Can Guo

[permalink] [raw]
Subject: [PATCH v7 01/10] scsi: ufs: host: Rename structure ufs_dev_params to ufs_host_params

Structure ufs_dev_params is actually used in UFS host vendor drivers to
declare host specific power mode parameters, like ufs_<vendor>_params or
host_cap, which makes the code not very straightforward to read. Rename the
structure ufs_dev_params to ufs_host_params and unify the declarations in
all vendor drivers to host_params.

In addition, rename the two functions ufshcd_init_pwr_dev_param() and
ufshcd_get_pwr_dev_param() which work based on the ufs_host_params to
ufshcd_init_host_params() and ufshcd_negotiate_pwr_params() respectively to
avoid confusions.

This change does not change any functionalities or logic.

Acked-by: Andrew Halaney <[email protected]>
Reviewed-by: Nitin Rawat <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Can Guo <[email protected]>
---
drivers/ufs/host/ufs-exynos.c | 7 ++--
drivers/ufs/host/ufs-hisi.c | 11 +++----
drivers/ufs/host/ufs-mediatek.c | 12 +++----
drivers/ufs/host/ufs-qcom.c | 12 +++----
drivers/ufs/host/ufshcd-pltfrm.c | 69 ++++++++++++++++++++--------------------
drivers/ufs/host/ufshcd-pltfrm.h | 10 +++---
6 files changed, 57 insertions(+), 64 deletions(-)

diff --git a/drivers/ufs/host/ufs-exynos.c b/drivers/ufs/host/ufs-exynos.c
index 71bd6db..734d40f 100644
--- a/drivers/ufs/host/ufs-exynos.c
+++ b/drivers/ufs/host/ufs-exynos.c
@@ -765,7 +765,7 @@ static int exynos_ufs_pre_pwr_mode(struct ufs_hba *hba,
{
struct exynos_ufs *ufs = ufshcd_get_variant(hba);
struct phy *generic_phy = ufs->phy;
- struct ufs_dev_params ufs_exynos_cap;
+ struct ufs_host_params host_params;
int ret;

if (!dev_req_params) {
@@ -774,10 +774,9 @@ static int exynos_ufs_pre_pwr_mode(struct ufs_hba *hba,
goto out;
}

- ufshcd_init_pwr_dev_param(&ufs_exynos_cap);
+ ufshcd_init_host_params(&host_params);

- ret = ufshcd_get_pwr_dev_param(&ufs_exynos_cap,
- dev_max_params, dev_req_params);
+ ret = ufshcd_negotiate_pwr_params(&host_params, dev_max_params, dev_req_params);
if (ret) {
pr_err("%s: failed to determine capabilities\n", __func__);
goto out;
diff --git a/drivers/ufs/host/ufs-hisi.c b/drivers/ufs/host/ufs-hisi.c
index 0229ac0..5ee73ff 100644
--- a/drivers/ufs/host/ufs-hisi.c
+++ b/drivers/ufs/host/ufs-hisi.c
@@ -293,9 +293,9 @@ static int ufs_hisi_link_startup_notify(struct ufs_hba *hba,
return err;
}

-static void ufs_hisi_set_dev_cap(struct ufs_dev_params *hisi_param)
+static void ufs_hisi_set_dev_cap(struct ufs_host_params *host_params)
{
- ufshcd_init_pwr_dev_param(hisi_param);
+ ufshcd_init_host_params(host_params);
}

static void ufs_hisi_pwr_change_pre_change(struct ufs_hba *hba)
@@ -365,7 +365,7 @@ static int ufs_hisi_pwr_change_notify(struct ufs_hba *hba,
struct ufs_pa_layer_attr *dev_max_params,
struct ufs_pa_layer_attr *dev_req_params)
{
- struct ufs_dev_params ufs_hisi_cap;
+ struct ufs_host_params host_params;
int ret = 0;

if (!dev_req_params) {
@@ -377,9 +377,8 @@ static int ufs_hisi_pwr_change_notify(struct ufs_hba *hba,

switch (status) {
case PRE_CHANGE:
- ufs_hisi_set_dev_cap(&ufs_hisi_cap);
- ret = ufshcd_get_pwr_dev_param(&ufs_hisi_cap,
- dev_max_params, dev_req_params);
+ ufs_hisi_set_dev_cap(&host_params);
+ ret = ufshcd_negotiate_pwr_params(&host_params, dev_max_params, dev_req_params);
if (ret) {
dev_err(hba->dev,
"%s: failed to determine capabilities\n", __func__);
diff --git a/drivers/ufs/host/ufs-mediatek.c b/drivers/ufs/host/ufs-mediatek.c
index fc61790..776bca4 100644
--- a/drivers/ufs/host/ufs-mediatek.c
+++ b/drivers/ufs/host/ufs-mediatek.c
@@ -996,16 +996,14 @@ static int ufs_mtk_pre_pwr_change(struct ufs_hba *hba,
struct ufs_pa_layer_attr *dev_req_params)
{
struct ufs_mtk_host *host = ufshcd_get_variant(hba);
- struct ufs_dev_params host_cap;
+ struct ufs_host_params host_params;
int ret;

- ufshcd_init_pwr_dev_param(&host_cap);
- host_cap.hs_rx_gear = UFS_HS_G5;
- host_cap.hs_tx_gear = UFS_HS_G5;
+ ufshcd_init_host_params(&host_params);
+ host_params.hs_rx_gear = UFS_HS_G5;
+ host_params.hs_tx_gear = UFS_HS_G5;

- ret = ufshcd_get_pwr_dev_param(&host_cap,
- dev_max_params,
- dev_req_params);
+ ret = ufshcd_negotiate_pwr_params(&host_params, dev_max_params, dev_req_params);
if (ret) {
pr_info("%s: failed to determine capabilities\n",
__func__);
diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 96cb8b5..197c5a5 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -898,7 +898,7 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
struct ufs_pa_layer_attr *dev_req_params)
{
struct ufs_qcom_host *host = ufshcd_get_variant(hba);
- struct ufs_dev_params ufs_qcom_cap;
+ struct ufs_host_params host_params;
int ret = 0;

if (!dev_req_params) {
@@ -908,15 +908,13 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,

switch (status) {
case PRE_CHANGE:
- ufshcd_init_pwr_dev_param(&ufs_qcom_cap);
- ufs_qcom_cap.hs_rate = UFS_QCOM_LIMIT_HS_RATE;
+ ufshcd_init_host_params(&host_params);
+ host_params.hs_rate = UFS_QCOM_LIMIT_HS_RATE;

/* This driver only supports symmetic gear setting i.e., hs_tx_gear == hs_rx_gear */
- ufs_qcom_cap.hs_tx_gear = ufs_qcom_cap.hs_rx_gear = ufs_qcom_get_hs_gear(hba);
+ host_params.hs_tx_gear = host_params.hs_rx_gear = ufs_qcom_get_hs_gear(hba);

- ret = ufshcd_get_pwr_dev_param(&ufs_qcom_cap,
- dev_max_params,
- dev_req_params);
+ ret = ufshcd_negotiate_pwr_params(&host_params, dev_max_params, dev_req_params);
if (ret) {
dev_err(hba->dev, "%s: failed to determine capabilities\n",
__func__);
diff --git a/drivers/ufs/host/ufshcd-pltfrm.c b/drivers/ufs/host/ufshcd-pltfrm.c
index da2558e..1633edc 100644
--- a/drivers/ufs/host/ufshcd-pltfrm.c
+++ b/drivers/ufs/host/ufshcd-pltfrm.c
@@ -285,61 +285,60 @@ static int ufshcd_parse_operating_points(struct ufs_hba *hba)
}

/**
- * ufshcd_get_pwr_dev_param - get finally agreed attributes for
- * power mode change
- * @pltfrm_param: pointer to platform parameters
+ * ufshcd_negotiate_pwr_params - find power mode settings that are supported by
+ both the controller and the device
+ * @host_params: pointer to host parameters
* @dev_max: pointer to device attributes
* @agreed_pwr: returned agreed attributes
*
* Return: 0 on success, non-zero value on failure.
*/
-int ufshcd_get_pwr_dev_param(const struct ufs_dev_params *pltfrm_param,
- const struct ufs_pa_layer_attr *dev_max,
- struct ufs_pa_layer_attr *agreed_pwr)
+int ufshcd_negotiate_pwr_params(const struct ufs_host_params *host_params,
+ const struct ufs_pa_layer_attr *dev_max,
+ struct ufs_pa_layer_attr *agreed_pwr)
{
- int min_pltfrm_gear;
+ int min_host_gear;
int min_dev_gear;
bool is_dev_sup_hs = false;
- bool is_pltfrm_max_hs = false;
+ bool is_host_max_hs = false;

if (dev_max->pwr_rx == FAST_MODE)
is_dev_sup_hs = true;

- if (pltfrm_param->desired_working_mode == UFS_HS_MODE) {
- is_pltfrm_max_hs = true;
- min_pltfrm_gear = min_t(u32, pltfrm_param->hs_rx_gear,
- pltfrm_param->hs_tx_gear);
+ if (host_params->desired_working_mode == UFS_HS_MODE) {
+ is_host_max_hs = true;
+ min_host_gear = min_t(u32, host_params->hs_rx_gear,
+ host_params->hs_tx_gear);
} else {
- min_pltfrm_gear = min_t(u32, pltfrm_param->pwm_rx_gear,
- pltfrm_param->pwm_tx_gear);
+ min_host_gear = min_t(u32, host_params->pwm_rx_gear,
+ host_params->pwm_tx_gear);
}

/*
- * device doesn't support HS but
- * pltfrm_param->desired_working_mode is HS,
- * thus device and pltfrm_param don't agree
+ * device doesn't support HS but host_params->desired_working_mode is HS,
+ * thus device and host_params don't agree
*/
- if (!is_dev_sup_hs && is_pltfrm_max_hs) {
+ if (!is_dev_sup_hs && is_host_max_hs) {
pr_info("%s: device doesn't support HS\n",
__func__);
return -ENOTSUPP;
- } else if (is_dev_sup_hs && is_pltfrm_max_hs) {
+ } else if (is_dev_sup_hs && is_host_max_hs) {
/*
* since device supports HS, it supports FAST_MODE.
- * since pltfrm_param->desired_working_mode is also HS
+ * since host_params->desired_working_mode is also HS
* then final decision (FAST/FASTAUTO) is done according
* to pltfrm_params as it is the restricting factor
*/
- agreed_pwr->pwr_rx = pltfrm_param->rx_pwr_hs;
+ agreed_pwr->pwr_rx = host_params->rx_pwr_hs;
agreed_pwr->pwr_tx = agreed_pwr->pwr_rx;
} else {
/*
- * here pltfrm_param->desired_working_mode is PWM.
+ * here host_params->desired_working_mode is PWM.
* it doesn't matter whether device supports HS or PWM,
- * in both cases pltfrm_param->desired_working_mode will
+ * in both cases host_params->desired_working_mode will
* determine the mode
*/
- agreed_pwr->pwr_rx = pltfrm_param->rx_pwr_pwm;
+ agreed_pwr->pwr_rx = host_params->rx_pwr_pwm;
agreed_pwr->pwr_tx = agreed_pwr->pwr_rx;
}

@@ -349,9 +348,9 @@ int ufshcd_get_pwr_dev_param(const struct ufs_dev_params *pltfrm_param,
* the same decision will be made for rx
*/
agreed_pwr->lane_tx = min_t(u32, dev_max->lane_tx,
- pltfrm_param->tx_lanes);
+ host_params->tx_lanes);
agreed_pwr->lane_rx = min_t(u32, dev_max->lane_rx,
- pltfrm_param->rx_lanes);
+ host_params->rx_lanes);

/* device maximum gear is the minimum between device rx and tx gears */
min_dev_gear = min_t(u32, dev_max->gear_rx, dev_max->gear_tx);
@@ -364,26 +363,26 @@ int ufshcd_get_pwr_dev_param(const struct ufs_dev_params *pltfrm_param,
* what is the gear, as it is the one that also decided previously what
* pwr the device will be configured to.
*/
- if ((is_dev_sup_hs && is_pltfrm_max_hs) ||
- (!is_dev_sup_hs && !is_pltfrm_max_hs)) {
+ if ((is_dev_sup_hs && is_host_max_hs) ||
+ (!is_dev_sup_hs && !is_host_max_hs)) {
agreed_pwr->gear_rx =
- min_t(u32, min_dev_gear, min_pltfrm_gear);
+ min_t(u32, min_dev_gear, min_host_gear);
} else if (!is_dev_sup_hs) {
agreed_pwr->gear_rx = min_dev_gear;
} else {
- agreed_pwr->gear_rx = min_pltfrm_gear;
+ agreed_pwr->gear_rx = min_host_gear;
}
agreed_pwr->gear_tx = agreed_pwr->gear_rx;

- agreed_pwr->hs_rate = pltfrm_param->hs_rate;
+ agreed_pwr->hs_rate = host_params->hs_rate;

return 0;
}
-EXPORT_SYMBOL_GPL(ufshcd_get_pwr_dev_param);
+EXPORT_SYMBOL_GPL(ufshcd_negotiate_pwr_params);

-void ufshcd_init_pwr_dev_param(struct ufs_dev_params *dev_param)
+void ufshcd_init_host_params(struct ufs_host_params *host_params)
{
- *dev_param = (struct ufs_dev_params){
+ *host_params = (struct ufs_host_params){
.tx_lanes = UFS_LANE_2,
.rx_lanes = UFS_LANE_2,
.hs_rx_gear = UFS_HS_G3,
@@ -398,7 +397,7 @@ void ufshcd_init_pwr_dev_param(struct ufs_dev_params *dev_param)
.desired_working_mode = UFS_HS_MODE,
};
}
-EXPORT_SYMBOL_GPL(ufshcd_init_pwr_dev_param);
+EXPORT_SYMBOL_GPL(ufshcd_init_host_params);

/**
* ufshcd_pltfrm_init - probe routine of the driver
diff --git a/drivers/ufs/host/ufshcd-pltfrm.h b/drivers/ufs/host/ufshcd-pltfrm.h
index a86a3ad..df387be 100644
--- a/drivers/ufs/host/ufshcd-pltfrm.h
+++ b/drivers/ufs/host/ufshcd-pltfrm.h
@@ -10,7 +10,7 @@
#define UFS_PWM_MODE 1
#define UFS_HS_MODE 2

-struct ufs_dev_params {
+struct ufs_host_params {
u32 pwm_rx_gear; /* pwm rx gear to work in */
u32 pwm_tx_gear; /* pwm tx gear to work in */
u32 hs_rx_gear; /* hs rx gear to work in */
@@ -25,10 +25,10 @@ struct ufs_dev_params {
u32 desired_working_mode;
};

-int ufshcd_get_pwr_dev_param(const struct ufs_dev_params *dev_param,
- const struct ufs_pa_layer_attr *dev_max,
- struct ufs_pa_layer_attr *agreed_pwr);
-void ufshcd_init_pwr_dev_param(struct ufs_dev_params *dev_param);
+int ufshcd_negotiate_pwr_params(const struct ufs_host_params *host_params,
+ const struct ufs_pa_layer_attr *dev_max,
+ struct ufs_pa_layer_attr *agreed_pwr);
+void ufshcd_init_host_params(struct ufs_host_params *host_params);
int ufshcd_pltfrm_init(struct platform_device *pdev,
const struct ufs_hba_variant_ops *vops);
int ufshcd_populate_vreg(struct device *dev, const char *name,
--
2.7.4

2023-12-01 05:43:31

by Manivannan Sadhasivam

[permalink] [raw]
Subject: Re: [PATCH v7 07/10] scsi: ufs: ufs-qcom: Check return value of phy_set_mode_ext()

On Thu, Nov 30, 2023 at 09:03:17PM -0800, Can Guo wrote:
> In ufs_qcom_power_up_sequence(), check return value of phy_set_mode_ext()
> and stop proceeding if phy_set_mode_ext() fails.
>
> Reviewed-by: Nitin Rawat <[email protected]>
> Signed-off-by: Can Guo <[email protected]>

Reviewed-by: Manivannan Sadhasivam <[email protected]>

- Mani

> ---
> drivers/ufs/host/ufs-qcom.c | 4 +++-
> 1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 543939c..ee3f07a 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -475,7 +475,9 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
> return ret;
> }
>
> - phy_set_mode_ext(phy, mode, host->phy_gear);
> + ret = phy_set_mode_ext(phy, mode, host->phy_gear);
> + if (ret)
> + goto out_disable_phy;
>
> /* power on phy - start serdes and phy's power and clocks */
> ret = phy_power_on(phy);
> --
> 2.7.4
>

--
மணிவண்ணன் சதாசிவம்

2023-12-01 05:46:45

by Manivannan Sadhasivam

[permalink] [raw]
Subject: Re: [PATCH v7 10/10] phy: qualcomm: phy-qcom-qmp-ufs: Add High Speed Gear 5 support for SM8550

On Thu, Nov 30, 2023 at 09:03:20PM -0800, Can Guo wrote:
> On SM8550, two sets of UFS PHY settings are provided, one set is to support
> HS-G5, another set is to support HS-G4 and lower gears. The two sets of PHY
> settings are programming different values to different registers, mixing
> the two sets and/or overwriting one set with another set is definitely not
> blessed by UFS PHY designers.
>
> To add HS-G5 support for SM8550, split the two sets of PHY settings into
> their dedicated overlay tables, only the common parts of the two sets of
> PHY settings are left in the .tbls.
>
> Consider we are going to add even higher gear support in future, to avoid
> adding more tables with different names, rename the .tbls_hs_g4 and make it
> an array, a size of 2 is enough as of now.
>
> In this case, .tbls alone is not a complete set of PHY settings, so either
> tbls_hs_overlay[0] or tbls_hs_overlay[1] must be applied on top of the
> .tbls to become a complete set of PHY settings.
>
> Signed-off-by: Can Guo <[email protected]>

Reviewed-by: Manivannan Sadhasivam <[email protected]>

- Mani

> ---
> drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h | 2 +
> drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h | 2 +
> .../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 8 +
> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 169 ++++++++++++++++++---
> 4 files changed, 159 insertions(+), 22 deletions(-)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
> index fe6c450..970cc06 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
> @@ -19,6 +19,7 @@
> #define QPHY_V6_PCS_UFS_BIST_FIXED_PAT_CTRL 0x060
> #define QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY 0x074
> #define QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY 0x0bc
> +#define QPHY_V6_PCS_UFS_RX_HS_G5_SYNC_LENGTH_CAPABILITY 0x12c
> #define QPHY_V6_PCS_UFS_DEBUG_BUS_CLKSEL 0x158
> #define QPHY_V6_PCS_UFS_LINECFG_DISABLE 0x17c
> #define QPHY_V6_PCS_UFS_RX_MIN_HIBERN8_TIME 0x184
> @@ -28,5 +29,6 @@
> #define QPHY_V6_PCS_UFS_READY_STATUS 0x1a8
> #define QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1 0x1f4
> #define QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1 0x1fc
> +#define QPHY_V6_PCS_UFS_RX_HSG5_SYNC_WAIT_TIME 0x220
>
> #endif
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
> index f420f8f..ef392ce 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
> @@ -56,6 +56,8 @@
> #define QSERDES_V6_COM_SYS_CLK_CTRL 0xe4
> #define QSERDES_V6_COM_SYSCLK_BUF_ENABLE 0xe8
> #define QSERDES_V6_COM_PLL_IVCO 0xf4
> +#define QSERDES_V6_COM_CMN_IETRIM 0xfc
> +#define QSERDES_V6_COM_CMN_IPTRIM 0x100
> #define QSERDES_V6_COM_SYSCLK_EN_SEL 0x110
> #define QSERDES_V6_COM_RESETSM_CNTRL 0x118
> #define QSERDES_V6_COM_LOCK_CMP_EN 0x120
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> index 35d497f..d9a87bd 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> @@ -15,13 +15,19 @@
>
> #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2 0x08
> #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4 0x10
> +#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_SO_GAIN_RATE4 0x24
> #define QSERDES_UFS_V6_RX_UCDR_SO_SATURATION 0x28
> +#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4 0x54
> #define QSERDES_UFS_V6_RX_UCDR_PI_CTRL1 0x58
> #define QSERDES_UFS_V6_RX_RX_TERM_BW_CTRL0 0xc4
> #define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2 0xd4
> #define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4 0xdc
> +#define QSERDES_UFS_V6_RX_UCDR_SO_GAIN_RATE4 0xf0
> +#define QSERDES_UFS_V6_RX_UCDR_PI_CONTROLS 0xf4
> #define QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL 0x178
> +#define QSERDES_UFS_V6_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x1bc
> #define QSERDES_UFS_V6_RX_INTERFACE_MODE 0x1e0
> +#define QSERDES_UFS_V6_RX_OFFSET_ADAPTOR_CNTRL3 0x1c4
> #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0 0x208
> #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1 0x20c
> #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B3 0x214
> @@ -33,6 +39,8 @@
> #define QSERDES_UFS_V6_RX_MODE_RATE3_B5 0x264
> #define QSERDES_UFS_V6_RX_MODE_RATE3_B8 0x270
> #define QSERDES_UFS_V6_RX_MODE_RATE4_B3 0x280
> +#define QSERDES_UFS_V6_RX_MODE_RATE4_B4 0x284
> #define QSERDES_UFS_V6_RX_MODE_RATE4_B6 0x28c
> +#define QSERDES_UFS_V6_RX_DLL0_FTUNE_CTRL 0x2f8
>
> #endif
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> index 3c2e625..11cea34 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> @@ -41,6 +41,8 @@
>
> #define PHY_INIT_COMPLETE_TIMEOUT 10000
>
> +#define NUM_OVERLAY 2
> +
> struct qmp_phy_init_tbl {
> unsigned int offset;
> unsigned int val;
> @@ -754,15 +756,22 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x11),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x01),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_INITVAL2, 0x00),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_serdes[] = {
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x0a),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
> @@ -771,19 +780,24 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
> };
>
> -static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_serdes[] = {
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x1f),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IETRIM, 0x1b),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IPTRIM, 0x1c),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
> };
>
> static const struct qmp_phy_init_tbl sm8550_ufsphy_tx[] = {
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_LANE_MODE_1, 0x05),
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_tx[] = {
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_FR_DCC_CTRL, 0x4c),
> };
>
> static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2, 0x0c),
> - QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),
>
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0, 0xc2),
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1, 0xc2),
> @@ -799,16 +813,45 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE3_B8, 0x02),
> };
>
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_rx[] = {
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_rx[] = {
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4, 0x0c),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_SO_GAIN_RATE4, 0x04),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x14),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_PI_CONTROLS, 0x07),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_OFFSET_ADAPTOR_CNTRL3, 0x0e),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4, 0x02),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4, 0x1c),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_SO_GAIN_RATE4, 0x06),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x08),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B3, 0xb9),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B4, 0x4f),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE4_B6, 0xff),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_DLL0_FTUNE_CTRL, 0x30),
> +};
> +
> static const struct qmp_phy_init_tbl sm8550_ufsphy_pcs[] = {
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_SIGDET_CTRL2, 0x69),
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0f),
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
> - QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_pcs[] = {
> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x04),
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x04),
> };
>
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_g5_pcs[] = {
> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x33),
> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HS_G5_SYNC_LENGTH_CAPABILITY, 0x4f),
> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSG5_SYNC_WAIT_TIME, 0x9e),
> +};
> +
> static const struct qmp_phy_init_tbl sm8650_ufsphy_serdes[] = {
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
> @@ -889,6 +932,8 @@ struct qmp_phy_cfg_tbls {
> int rx_num;
> const struct qmp_phy_init_tbl *pcs;
> int pcs_num;
> + /* Maximum supported Gear of this tbls */
> + u32 max_gear;
> };
>
> /* struct qmp_phy_cfg - per-PHY initialization config */
> @@ -896,13 +941,15 @@ struct qmp_phy_cfg {
> int lanes;
>
> const struct qmp_ufs_offsets *offsets;
> + /* Maximum supported Gear of this config */
> + u32 max_supported_gear;
>
> /* Main init sequence for PHY blocks - serdes, tx, rx, pcs */
> const struct qmp_phy_cfg_tbls tbls;
> /* Additional sequence for HS Series B */
> const struct qmp_phy_cfg_tbls tbls_hs_b;
> - /* Additional sequence for HS G4 */
> - const struct qmp_phy_cfg_tbls tbls_hs_g4;
> + /* Additional sequence for different HS Gears */
> + const struct qmp_phy_cfg_tbls tbls_hs_overlay[NUM_OVERLAY];
>
> /* clock ids to be requested */
> const char * const *clk_list;
> @@ -1005,6 +1052,7 @@ static const struct qmp_phy_cfg msm8996_ufsphy_cfg = {
> .lanes = 1,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G3,
>
> .tbls = {
> .serdes = msm8996_ufsphy_serdes,
> @@ -1030,6 +1078,7 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G4,
>
> .tbls = {
> .serdes = sm8350_ufsphy_serdes,
> @@ -1045,13 +1094,14 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = {
> .serdes = sm8350_ufsphy_hs_b_serdes,
> .serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
> },
> - .tbls_hs_g4 = {
> + .tbls_hs_overlay[0] = {
> .tx = sm8350_ufsphy_g4_tx,
> .tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
> .rx = sm8350_ufsphy_g4_rx,
> .rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
> .pcs = sm8350_ufsphy_g4_pcs,
> .pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
> + .max_gear = UFS_HS_G4,
> },
> .clk_list = sm8450_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
> @@ -1064,6 +1114,7 @@ static const struct qmp_phy_cfg sc7280_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G4,
>
> .tbls = {
> .serdes = sm8150_ufsphy_serdes,
> @@ -1079,13 +1130,14 @@ static const struct qmp_phy_cfg sc7280_ufsphy_cfg = {
> .serdes = sm8150_ufsphy_hs_b_serdes,
> .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
> },
> - .tbls_hs_g4 = {
> + .tbls_hs_overlay[0] = {
> .tx = sm8250_ufsphy_hs_g4_tx,
> .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx),
> .rx = sc7280_ufsphy_hs_g4_rx,
> .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx),
> .pcs = sm8150_ufsphy_hs_g4_pcs,
> .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
> + .max_gear = UFS_HS_G4,
> },
> .clk_list = sm8450_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
> @@ -1098,6 +1150,7 @@ static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G4,
>
> .tbls = {
> .serdes = sm8350_ufsphy_serdes,
> @@ -1113,13 +1166,14 @@ static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = {
> .serdes = sm8350_ufsphy_hs_b_serdes,
> .serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
> },
> - .tbls_hs_g4 = {
> + .tbls_hs_overlay[0] = {
> .tx = sm8350_ufsphy_g4_tx,
> .tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
> .rx = sm8350_ufsphy_g4_rx,
> .rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
> .pcs = sm8350_ufsphy_g4_pcs,
> .pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
> + .max_gear = UFS_HS_G4,
> },
> .clk_list = sdm845_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
> @@ -1132,6 +1186,7 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G3,
>
> .tbls = {
> .serdes = sdm845_ufsphy_serdes,
> @@ -1160,6 +1215,7 @@ static const struct qmp_phy_cfg sm6115_ufsphy_cfg = {
> .lanes = 1,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G3,
>
> .tbls = {
> .serdes = sm6115_ufsphy_serdes,
> @@ -1188,6 +1244,7 @@ static const struct qmp_phy_cfg sm7150_ufsphy_cfg = {
> .lanes = 1,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G3,
>
> .tbls = {
> .serdes = sdm845_ufsphy_serdes,
> @@ -1216,6 +1273,7 @@ static const struct qmp_phy_cfg sm8150_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G4,
>
> .tbls = {
> .serdes = sm8150_ufsphy_serdes,
> @@ -1231,13 +1289,14 @@ static const struct qmp_phy_cfg sm8150_ufsphy_cfg = {
> .serdes = sm8150_ufsphy_hs_b_serdes,
> .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
> },
> - .tbls_hs_g4 = {
> + .tbls_hs_overlay[0] = {
> .tx = sm8150_ufsphy_hs_g4_tx,
> .tx_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_tx),
> .rx = sm8150_ufsphy_hs_g4_rx,
> .rx_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_rx),
> .pcs = sm8150_ufsphy_hs_g4_pcs,
> .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
> + .max_gear = UFS_HS_G4,
> },
> .clk_list = sdm845_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
> @@ -1250,6 +1309,7 @@ static const struct qmp_phy_cfg sm8250_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G4,
>
> .tbls = {
> .serdes = sm8150_ufsphy_serdes,
> @@ -1265,13 +1325,14 @@ static const struct qmp_phy_cfg sm8250_ufsphy_cfg = {
> .serdes = sm8150_ufsphy_hs_b_serdes,
> .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
> },
> - .tbls_hs_g4 = {
> + .tbls_hs_overlay[0] = {
> .tx = sm8250_ufsphy_hs_g4_tx,
> .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx),
> .rx = sm8250_ufsphy_hs_g4_rx,
> .rx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_rx),
> .pcs = sm8150_ufsphy_hs_g4_pcs,
> .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
> + .max_gear = UFS_HS_G4,
> },
> .clk_list = sdm845_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
> @@ -1284,6 +1345,7 @@ static const struct qmp_phy_cfg sm8350_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G4,
>
> .tbls = {
> .serdes = sm8350_ufsphy_serdes,
> @@ -1299,13 +1361,14 @@ static const struct qmp_phy_cfg sm8350_ufsphy_cfg = {
> .serdes = sm8350_ufsphy_hs_b_serdes,
> .serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
> },
> - .tbls_hs_g4 = {
> + .tbls_hs_overlay[0] = {
> .tx = sm8350_ufsphy_g4_tx,
> .tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
> .rx = sm8350_ufsphy_g4_rx,
> .rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
> .pcs = sm8350_ufsphy_g4_pcs,
> .pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
> + .max_gear = UFS_HS_G4,
> },
> .clk_list = sdm845_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
> @@ -1318,6 +1381,7 @@ static const struct qmp_phy_cfg sm8450_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets,
> + .max_supported_gear = UFS_HS_G4,
>
> .tbls = {
> .serdes = sm8350_ufsphy_serdes,
> @@ -1333,13 +1397,14 @@ static const struct qmp_phy_cfg sm8450_ufsphy_cfg = {
> .serdes = sm8350_ufsphy_hs_b_serdes,
> .serdes_num = ARRAY_SIZE(sm8350_ufsphy_hs_b_serdes),
> },
> - .tbls_hs_g4 = {
> + .tbls_hs_overlay[0] = {
> .tx = sm8350_ufsphy_g4_tx,
> .tx_num = ARRAY_SIZE(sm8350_ufsphy_g4_tx),
> .rx = sm8350_ufsphy_g4_rx,
> .rx_num = ARRAY_SIZE(sm8350_ufsphy_g4_rx),
> .pcs = sm8350_ufsphy_g4_pcs,
> .pcs_num = ARRAY_SIZE(sm8350_ufsphy_g4_pcs),
> + .max_gear = UFS_HS_G4,
> },
> .clk_list = sm8450_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
> @@ -1352,6 +1417,7 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets_v6,
> + .max_supported_gear = UFS_HS_G5,
>
> .tbls = {
> .serdes = sm8550_ufsphy_serdes,
> @@ -1367,6 +1433,26 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
> .serdes = sm8550_ufsphy_hs_b_serdes,
> .serdes_num = ARRAY_SIZE(sm8550_ufsphy_hs_b_serdes),
> },
> + .tbls_hs_overlay[0] = {
> + .serdes = sm8550_ufsphy_g4_serdes,
> + .serdes_num = ARRAY_SIZE(sm8550_ufsphy_g4_serdes),
> + .tx = sm8550_ufsphy_g4_tx,
> + .tx_num = ARRAY_SIZE(sm8550_ufsphy_g4_tx),
> + .rx = sm8550_ufsphy_g4_rx,
> + .rx_num = ARRAY_SIZE(sm8550_ufsphy_g4_rx),
> + .pcs = sm8550_ufsphy_g4_pcs,
> + .pcs_num = ARRAY_SIZE(sm8550_ufsphy_g4_pcs),
> + .max_gear = UFS_HS_G4,
> + },
> + .tbls_hs_overlay[1] = {
> + .serdes = sm8550_ufsphy_g5_serdes,
> + .serdes_num = ARRAY_SIZE(sm8550_ufsphy_g5_serdes),
> + .rx = sm8550_ufsphy_g5_rx,
> + .rx_num = ARRAY_SIZE(sm8550_ufsphy_g5_rx),
> + .pcs = sm8550_ufsphy_g5_pcs,
> + .pcs_num = ARRAY_SIZE(sm8550_ufsphy_g5_pcs),
> + .max_gear = UFS_HS_G5,
> + },
> .clk_list = sdm845_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
> .vreg_list = qmp_phy_vreg_l,
> @@ -1378,6 +1464,7 @@ static const struct qmp_phy_cfg sm8650_ufsphy_cfg = {
> .lanes = 2,
>
> .offsets = &qmp_ufs_offsets_v6,
> + .max_supported_gear = UFS_HS_G5,
>
> .tbls = {
> .serdes = sm8650_ufsphy_serdes,
> @@ -1451,17 +1538,49 @@ static void qmp_ufs_pcs_init(struct qmp_ufs *qmp, const struct qmp_phy_cfg_tbls
> qmp_ufs_configure(pcs, tbls->pcs, tbls->pcs_num);
> }
>
> +static int qmp_ufs_get_gear_overlay(struct qmp_ufs *qmp, const struct qmp_phy_cfg *cfg)
> +{
> + u32 max_gear, floor_max_gear = cfg->max_supported_gear;
> + int idx, ret = -EINVAL;
> +
> + for (idx = NUM_OVERLAY - 1; idx >= 0; idx--) {
> + max_gear = cfg->tbls_hs_overlay[idx].max_gear;
> +
> + /* Skip if the table is not available */
> + if (max_gear == 0)
> + continue;
> +
> + /* Direct matching, bail */
> + if (qmp->submode == max_gear)
> + return idx;
> +
> + /* If no direct matching, the lowest gear is the best matching */
> + if (max_gear < floor_max_gear) {
> + ret = idx;
> + floor_max_gear = max_gear;
> + }
> + }
> +
> + return ret;
> +}
> +
> static void qmp_ufs_init_registers(struct qmp_ufs *qmp, const struct qmp_phy_cfg *cfg)
> {
> + int i;
> +
> qmp_ufs_serdes_init(qmp, &cfg->tbls);
> - if (qmp->mode == PHY_MODE_UFS_HS_B)
> - qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_b);
> qmp_ufs_lanes_init(qmp, &cfg->tbls);
> - if (qmp->submode == UFS_HS_G4)
> - qmp_ufs_lanes_init(qmp, &cfg->tbls_hs_g4);
> qmp_ufs_pcs_init(qmp, &cfg->tbls);
> - if (qmp->submode == UFS_HS_G4)
> - qmp_ufs_pcs_init(qmp, &cfg->tbls_hs_g4);
> +
> + i = qmp_ufs_get_gear_overlay(qmp, cfg);
> + if (i >= 0) {
> + qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_overlay[i]);
> + qmp_ufs_lanes_init(qmp, &cfg->tbls_hs_overlay[i]);
> + qmp_ufs_pcs_init(qmp, &cfg->tbls_hs_overlay[i]);
> + }
> +
> + if (qmp->mode == PHY_MODE_UFS_HS_B)
> + qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_b);
> }
>
> static int qmp_ufs_com_init(struct qmp_ufs *qmp)
> @@ -1633,6 +1752,12 @@ static int qmp_ufs_disable(struct phy *phy)
> static int qmp_ufs_set_mode(struct phy *phy, enum phy_mode mode, int submode)
> {
> struct qmp_ufs *qmp = phy_get_drvdata(phy);
> + const struct qmp_phy_cfg *cfg = qmp->cfg;
> +
> + if (submode > cfg->max_supported_gear || submode == 0) {
> + dev_err(qmp->dev, "Invalid PHY submode %d\n", submode);
> + return -EINVAL;
> + }
>
> qmp->mode = mode;
> qmp->submode = submode;
> --
> 2.7.4
>

--
மணிவண்ணன் சதாசிவம்

2023-12-01 07:43:16

by Abel Vesa

[permalink] [raw]
Subject: Re: [PATCH v7 09/10] phy: qualcomm: phy-qcom-qmp-ufs: Rectify SM8550 UFS HS-G4 PHY Settings

On 23-11-30 21:03:19, Can Guo wrote:
> The registers, which are being touched in current SM8550 UFS PHY settings,
> and the values being programmed are mainly the ones working for HS-G4 mode,
> meanwhile, there are also a few ones somehow taken from HS-G5 PHY settings.
> However, even consider HS-G4 mode only, some of them are incorrect and some
> are missing. Rectify the HS-G4 PHY settings by strictly aligning with the
> SM8550 UFS PHY Hardware Programming Guide suggested HS-G4 PHY settings.
>
> Fixes: 1679bfef906f ("phy: qcom-qmp-ufs: Add SM8550 support")
> Reviewed-by: Dmitry Baryshkov <[email protected]>
> Reviewed-by: Abel Vesa <[email protected]>
> Reviewed-by: Manivannan Sadhasivam <[email protected]>
> Signed-off-by: Can Guo <[email protected]>
> ---

Hi Can,

Since you are not CC'ing everyone on all patches from this series,
please write the changes made since the last version in every patch (if
applicable) from now on.

Thanks,
Abel

> .../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 1 +
> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 28 +++++++++++++++-------
> 2 files changed, 20 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> index ae220fd..35d497f 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> @@ -11,6 +11,7 @@
> #define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX 0x30
> #define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_RX 0x34
> #define QSERDES_UFS_V6_TX_LANE_MODE_1 0x7c
> +#define QSERDES_UFS_V6_TX_FR_DCC_CTRL 0x108
>
> #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2 0x08
> #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4 0x10
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> index 5f79d18..3c2e625 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> @@ -763,22 +763,26 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x4c),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x99),
> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x07),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x0a),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x14),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x99),
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
> +};
> +
> +static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
> };
>
> static const struct qmp_phy_init_tbl sm8550_ufsphy_tx[] = {
> - QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0x05),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_LANE_MODE_1, 0x05),
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_FR_DCC_CTRL, 0x4c),
> };
>
> static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
> - QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2, 0x0c),
> - QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4, 0x0f),
> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2, 0x0c),
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),
>
> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0, 0xc2),
> @@ -801,6 +805,8 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_pcs[] = {
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x04),
> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x04),
> };
>
> static const struct qmp_phy_init_tbl sm8650_ufsphy_serdes[] = {
> @@ -1357,6 +1363,10 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
> .pcs = sm8550_ufsphy_pcs,
> .pcs_num = ARRAY_SIZE(sm8550_ufsphy_pcs),
> },
> + .tbls_hs_b = {
> + .serdes = sm8550_ufsphy_hs_b_serdes,
> + .serdes_num = ARRAY_SIZE(sm8550_ufsphy_hs_b_serdes),
> + },
> .clk_list = sdm845_ufs_phy_clk_l,
> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
> .vreg_list = qmp_phy_vreg_l,
> --
> 2.7.4
>

2023-12-01 09:22:18

by Nitin Rawat

[permalink] [raw]
Subject: Re: [PATCH v7 04/10] scsi: ufs: ufs-qcom: Allow the first init start with the maximum supported gear



On 12/1/2023 10:33 AM, Can Guo wrote:
> During host driver init, the phy_gear is set to the minimum supported gear
> (HS_G2). Then, during the first power mode change, the negotiated gear, say
> HS-G4, is updated to the phy_gear variable so that in the second init the
> updated phy_gear can be used to program the PHY.
>
> But the current code only allows update the phy_gear to a higher value. If
> one wants to start the first init with the maximum support gear, say HS-G4,
> the phy_gear is not updated to HS-G3 if the device only supports HS-G3.
>
> The original check added there is intend to make sure the phy_gear won't be
> updated when gear is scaled down (during clock scaling). Update the check
> so that one can start the first init with the maximum support gear without
> breaking the original fix by checking the ufshcd_state, that is, allow
> update to phy_gear only if power mode change is invoked from
> ufshcd_probe_hba().
>
> Reviewed-by: Manivannan Sadhasivam <[email protected]>
> Signed-off-by: Can Guo <[email protected]>
> ---
> drivers/ufs/host/ufs-qcom.c | 9 +++++----
> 1 file changed, 5 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 9a90019..81056b9 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -916,11 +916,12 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
> }
>
> /*
> - * Update phy_gear only when the gears are scaled to a higher value. This is
> - * because, the PHY gear settings are backwards compatible and we only need to
> - * change the PHY gear settings while scaling to higher gears.
> + * During UFS driver probe, always update the PHY gear to match the negotiated
> + * gear, so that, if quirk UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH is enabled,
> + * the second init can program the optimal PHY settings. This allows one to start
> + * the first init with either the minimum or the maximum support gear.
> */
> - if (dev_req_params->gear_tx > host->phy_gear)
> + if (hba->ufshcd_state == UFSHCD_STATE_RESET)
> host->phy_gear = dev_req_params->gear_tx;
>
> /* enable the device ref clock before changing to HS mode */

Reviewed-by: Nitin Rawat <[email protected]>

2023-12-01 10:10:08

by Neil Armstrong

[permalink] [raw]
Subject: Re: [PATCH v7 00/10] Enable HS-G5 support on SM8550

On 01/12/2023 06:03, Can Guo wrote:
> This series enables HS-G5 support on SM8550.
>
> This series is rebased on below changes from Mani -
> https://patchwork.kernel.org/project/linux-scsi/patch/[email protected]/
> https://patchwork.kernel.org/project/linux-scsi/patch/[email protected]/
>
> This series is tested on below HW combinations -
> SM8550 MTP + UFS4.0
> SM8550 QRD + UFS3.1
> SM8450 MTP + UFS3.1 (for regression test)
> SM8350 MTP + UFS3.1 (for regression test)
>
> Note that during reboot test on above platforms, I occasinally hit PA (PHY)
> error during the 2nd init, this is not related with this series. A fix for
> this is mentioned in below patchwork -
>
> https://patchwork.kernel.org/project/linux-scsi/patch/[email protected]/
>
> Also note that on platforms, which have two sets of UFS PHY settings are
> provided (say G4 and no-G4, G5 and no-G5). The two sets of PHY settings are
> basically programming different values to different registers, mixing the
> two sets and/or overwriting one set with another set is definitely not
> blessed by UFS PHY designers. For SM8550, this series will make sure we
> honor the rule. However, for old targets Mani and I will fix them in
> another series in future.
>
> v6 -> v7:
> 1. Rebased on linux-next, based SM8650 PHY settings are merged there, no changes to patches for UFS driver
> 2. Addressed comments from Mani
>
> v5 -> v6:
> 1. Rebased on scsi-queue-6.8
> 2. Addressed comments from Dmitry and Mani in patches to phy-qcom-qmp-ufs.c
>
> v4 -> v5:
> Removed two useless debug prints in patch #9
>
> v3 -> v4:
> Used .tbls_hs_overlay array instead of adding more tables with different names like .tbls_hs_g5
>
> v2 -> v3:
> 1. Addressed comments from Andrew, Mani and Bart in patch #1
> 2. Added patch #2 as per request from Andrew and Mani
> 3. Added patch #4 to fix a common issue on old targets, it is not necessary
> for this series, but put in this series only because it would be easier
> to maintain and no need to rebase
> 4. Addressed comments from Dmitry and Mani in patches to phy-qcom-qmp-ufs.c
>
> v1 -> v2:
> 1. Removed 2 changes which were exposing power info in sysfs
> 2. Removed 1 change which was moving data structs to phy-qcom-qmp-ufs.h
> 3. Added one new change (the 1st one) to clean up usage of ufs_dev_params based on comments from Mani
> 4. Adjusted the logic of UFS device version detection according to comments from Mani:
> 4.1 For HW version < 0x5, go through dual init
> 4.2 For HW version >= 0x5
> a. If UFS device version is populated, one init is required
> b. If UFS device version is not populated, go through dual init
>
> Bao D. Nguyen (1):
> scsi: ufs: ufs-qcom: Add support for UFS device version detection
>
> Can Guo (9):
> scsi: ufs: host: Rename structure ufs_dev_params to ufs_host_params
> scsi: ufs: ufs-qcom: No need to set hs_rate after
> ufshcd_init_host_param()
> scsi: ufs: ufs-qcom: Setup host power mode during init
> scsi: ufs: ufs-qcom: Allow the first init start with the maximum
> supported gear
> scsi: ufs: ufs-qcom: Limit HS-G5 Rate-A to hosts with HW version 5
> scsi: ufs: ufs-qcom: Set initial PHY gear to max HS gear for HW ver 4
> and newer
> scsi: ufs: ufs-qcom: Check return value of phy_set_mode_ext()
> phy: qualcomm: phy-qcom-qmp-ufs: Rectify SM8550 UFS HS-G4 PHY Settings
> phy: qualcomm: phy-qcom-qmp-ufs: Add High Speed Gear 5 support for
> SM8550
>
> drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h | 2 +
> drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h | 2 +
> .../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 9 +
> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 191 ++++++++++++++++++---
> drivers/ufs/host/ufs-exynos.c | 7 +-
> drivers/ufs/host/ufs-hisi.c | 11 +-
> drivers/ufs/host/ufs-mediatek.c | 12 +-
> drivers/ufs/host/ufs-qcom.c | 97 ++++++++---
> drivers/ufs/host/ufs-qcom.h | 7 +-
> drivers/ufs/host/ufshcd-pltfrm.c | 69 ++++----
> drivers/ufs/host/ufshcd-pltfrm.h | 10 +-
> 11 files changed, 309 insertions(+), 108 deletions(-)
>

Tested-by: Neil Armstrong <[email protected]> # on SM8550-QRD
Tested-by: Neil Armstrong <[email protected]> # on SM8650-QRD

Thanks,
Neil

2023-12-02 10:11:57

by Can Guo

[permalink] [raw]
Subject: Re: [PATCH v7 09/10] phy: qualcomm: phy-qcom-qmp-ufs: Rectify SM8550 UFS HS-G4 PHY Settings


On 12/1/2023 3:42 PM, Abel Vesa wrote:
> On 23-11-30 21:03:19, Can Guo wrote:
>> The registers, which are being touched in current SM8550 UFS PHY settings,
>> and the values being programmed are mainly the ones working for HS-G4 mode,
>> meanwhile, there are also a few ones somehow taken from HS-G5 PHY settings.
>> However, even consider HS-G4 mode only, some of them are incorrect and some
>> are missing. Rectify the HS-G4 PHY settings by strictly aligning with the
>> SM8550 UFS PHY Hardware Programming Guide suggested HS-G4 PHY settings.
>>
>> Fixes: 1679bfef906f ("phy: qcom-qmp-ufs: Add SM8550 support")
>> Reviewed-by: Dmitry Baryshkov <[email protected]>
>> Reviewed-by: Abel Vesa <[email protected]>
>> Reviewed-by: Manivannan Sadhasivam <[email protected]>
>> Signed-off-by: Can Guo <[email protected]>
>> ---
> Hi Can,
>
> Since you are not CC'ing everyone on all patches from this series,
> please write the changes made since the last version in every patch (if
> applicable) from now on.
>
> Thanks,
> Abel

Sure.


Thanks,

Can Guo.

>
>> .../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 1 +
>> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 28 +++++++++++++++-------
>> 2 files changed, 20 insertions(+), 9 deletions(-)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
>> index ae220fd..35d497f 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
>> @@ -11,6 +11,7 @@
>> #define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX 0x30
>> #define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_RX 0x34
>> #define QSERDES_UFS_V6_TX_LANE_MODE_1 0x7c
>> +#define QSERDES_UFS_V6_TX_FR_DCC_CTRL 0x108
>>
>> #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2 0x08
>> #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4 0x10
>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> index 5f79d18..3c2e625 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> @@ -763,22 +763,26 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
>> QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x4c),
>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x99),
>> - QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x07),
>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x0a),
>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x14),
>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x99),
>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
>> +};
>> +
>> +static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
>> + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
>> };
>>
>> static const struct qmp_phy_init_tbl sm8550_ufsphy_tx[] = {
>> - QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0x05),
>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_LANE_MODE_1, 0x05),
>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_TX_FR_DCC_CTRL, 0x4c),
>> };
>>
>> static const struct qmp_phy_init_tbl sm8550_ufsphy_rx[] = {
>> - QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2, 0x0c),
>> - QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4, 0x0f),
>> + QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2, 0x0c),
>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL, 0x0e),
>>
>> QMP_PHY_INIT_CFG(QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0, 0xc2),
>> @@ -801,6 +805,8 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_pcs[] = {
>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_PLL_CNTL, 0x2b),
>> QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
>> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x04),
>> + QMP_PHY_INIT_CFG(QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x04),
>> };
>>
>> static const struct qmp_phy_init_tbl sm8650_ufsphy_serdes[] = {
>> @@ -1357,6 +1363,10 @@ static const struct qmp_phy_cfg sm8550_ufsphy_cfg = {
>> .pcs = sm8550_ufsphy_pcs,
>> .pcs_num = ARRAY_SIZE(sm8550_ufsphy_pcs),
>> },
>> + .tbls_hs_b = {
>> + .serdes = sm8550_ufsphy_hs_b_serdes,
>> + .serdes_num = ARRAY_SIZE(sm8550_ufsphy_hs_b_serdes),
>> + },
>> .clk_list = sdm845_ufs_phy_clk_l,
>> .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
>> .vreg_list = qmp_phy_vreg_l,
>> --
>> 2.7.4
>>