This fixes the lost aliases for the IOT2050 series, fixes mini PCIe card
hangs,, drops an unused device node, brings runtime pinmuxing for the
Arduino connector via debugfs as well as spidev. Finally, it enables
PRU-based Ethernet on PG2/M.2 device variants (depends on [1]). PG1
devices still need changes to the TI driver to enable them as well.
Jan
[1] https://lore.kernel.org/lkml/[email protected]/
Benedikt Niedermayr (1):
arm64: dts: ti: iot2050: Definitions for runtime pinmuxing
Jan Kiszka (5):
arm64: dts: ti: iot2050: Re-add aliases
arm64: dts: ti: iot2050: Drop unused ecap0 PWM
dt-bindings: trivial-devices: Add IOT2050 Arduino SPI connector
arm64: dts: ti: iot2050: Add node for SPI devices on Arduino connector
arm64: dts: ti: iot2050: Add icssg-prueth nodes for PG2 devices
Su Bao Cheng (1):
arm64: dts: ti: iot2050: Refactor the m.2 and minipcie power pin
.../devicetree/bindings/trivial-devices.yaml | 2 +
.../dts/ti/k3-am65-iot2050-common-pg1.dtsi | 10 +-
.../dts/ti/k3-am65-iot2050-common-pg2.dtsi | 4 +-
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 834 +++++++++++++++++-
.../dts/ti/k3-am6548-iot2050-advanced-m2.dts | 12 +-
5 files changed, 802 insertions(+), 60 deletions(-)
--
2.35.3
From: Jan Kiszka <[email protected]>
This interface is normally driven by userspace on the IOT2050.
Signed-off-by: Jan Kiszka <[email protected]>
---
arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 53bd296ba310..bc77ba58d8f9 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -1180,6 +1180,12 @@ &mcu_spi0 {
#address-cells = <1>;
#size-cells = <0>;
ti,pindir-d0-out-d1-in;
+
+ spidev@0 {
+ compatible = "siemens,iot2050-arduino-spi";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
};
&tscadc1 {
--
2.35.3
From: Jan Kiszka <[email protected]>
On the Siemens IOT2050 devices, the SPI controller wired to the Arduino
connector is normally driven by userspace. Introduce a binding for use
by spidev.
Signed-off-by: Jan Kiszka <[email protected]>
---
Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
index 430a814f64a5..01b9f36afcd5 100644
--- a/Documentation/devicetree/bindings/trivial-devices.yaml
+++ b/Documentation/devicetree/bindings/trivial-devices.yaml
@@ -349,6 +349,8 @@ properties:
- silabs,si3210
# Relative Humidity and Temperature Sensors
- silabs,si7020
+ # Siemens IOT2050: SPI interface on Arduino connector
+ - siemens,iot2050-arduino-spi
# Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply
- skyworks,sky81452
# Socionext SynQuacer TPM MMIO module
--
2.35.3
From: Benedikt Niedermayr <[email protected]>
Add multiple device tree nodes in order to support
runtime pinmuxing via debugfs.
All nodes are added to the pinctrl device node,
since they are now belonging to multiple interfaces now.
Note: Pinconf is also handled by debugfs-pinmux. This is possible since
pinconf and pinmux accessing the same 32-Bit register and setting the
function mask to 32-Bit allows writes to the whole register.
Signed-off-by: Benedikt Niedermayr <[email protected]>
---
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 663 +++++++++++++++++-
.../dts/ti/k3-am6548-iot2050-advanced-m2.dts | 4 +-
2 files changed, 628 insertions(+), 39 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index fc39ae0f9587..74c4accff4b7 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -114,6 +114,425 @@ dp_refclk: clock {
};
&wkup_pmx0 {
+ pinctrl-names =
+ "default",
+ "d0-uart0-rxd", "d0-gpio", "d0-gpio-pullup", "d0-gpio-pulldown",
+ "d1-uart0-txd", "d1-gpio", "d1-gpio-pullup", "d1-gpio-pulldown",
+ "d2-uart0-ctsn", "d2-gpio", "d2-gpio-pullup", "d2-gpio-pulldown",
+ "d3-uart0-rtsn", "d3-gpio", "d3-gpio-pullup", "d3-gpio-pulldown",
+ "d10-spi0-cs0", "d10-gpio", "d10-gpio-pullup", "d10-gpio-pulldown",
+ "d11-spi0-d0", "d11-gpio", "d11-gpio-pullup", "d11-gpio-pulldown",
+ "d12-spi0-d1", "d12-gpio", "d12-gpio-pullup", "d12-gpio-pulldown",
+ "d13-spi0-clk", "d13-gpio", "d13-gpio-pullup", "d13-gpio-pulldown",
+ "a0-gpio", "a0-gpio-pullup", "a0-gpio-pulldown",
+ "a1-gpio", "a1-gpio-pullup", "a1-gpio-pulldown",
+ "a2-gpio", "a2-gpio-pullup", "a2-gpio-pulldown",
+ "a3-gpio", "a3-gpio-pullup", "a3-gpio-pulldown",
+ "a4-gpio", "a4-gpio-pullup", "a4-gpio-pulldown",
+ "a5-gpio", "a5-gpio-pullup", "a5-gpio-pulldown";
+
+ pinctrl-0 = <&d0_uart0_rxd>;
+ pinctrl-1 = <&d0_uart0_rxd>;
+ pinctrl-2 = <&d0_gpio>;
+ pinctrl-3 = <&d0_gpio_pullup>;
+ pinctrl-4 = <&d0_gpio_pulldown>;
+ pinctrl-5 = <&d1_uart0_txd>;
+ pinctrl-6 = <&d1_gpio>;
+ pinctrl-7 = <&d1_gpio_pullup>;
+ pinctrl-8 = <&d1_gpio_pulldown>;
+ pinctrl-9 = <&d2_uart0_ctsn>;
+ pinctrl-10 = <&d2_gpio>;
+ pinctrl-11 = <&d2_gpio_pullup>;
+ pinctrl-12 = <&d2_gpio_pulldown>;
+ pinctrl-13 = <&d3_uart0_rtsn>;
+ pinctrl-14 = <&d3_gpio>;
+ pinctrl-15 = <&d3_gpio_pullup>;
+ pinctrl-16 = <&d3_gpio_pulldown>;
+ pinctrl-17 = <&d10_spi0_cs0>;
+ pinctrl-18 = <&d10_gpio>;
+ pinctrl-19 = <&d10_gpio_pullup>;
+ pinctrl-20 = <&d10_gpio_pulldown>;
+ pinctrl-21 = <&d11_spi0_d0>;
+ pinctrl-22 = <&d11_gpio>;
+ pinctrl-23 = <&d11_gpio_pullup>;
+ pinctrl-24 = <&d11_gpio_pulldown>;
+ pinctrl-25 = <&d12_spi0_d1>;
+ pinctrl-26 = <&d12_gpio>;
+ pinctrl-27 = <&d12_gpio_pullup>;
+ pinctrl-28 = <&d12_gpio_pulldown>;
+ pinctrl-29 = <&d13_spi0_clk>;
+ pinctrl-30 = <&d13_gpio>;
+ pinctrl-31 = <&d13_gpio_pullup>;
+ pinctrl-32 = <&d13_gpio_pulldown>;
+ pinctrl-33 = <&a0_gpio>;
+ pinctrl-34 = <&a0_gpio_pullup>;
+ pinctrl-35 = <&a0_gpio_pulldown>;
+ pinctrl-36 = <&a1_gpio>;
+ pinctrl-37 = <&a1_gpio_pullup>;
+ pinctrl-38 = <&a1_gpio_pulldown>;
+ pinctrl-39 = <&a2_gpio>;
+ pinctrl-40 = <&a2_gpio_pullup>;
+ pinctrl-41 = <&a2_gpio_pulldown>;
+ pinctrl-42 = <&a3_gpio>;
+ pinctrl-43 = <&a3_gpio_pullup>;
+ pinctrl-44 = <&a3_gpio_pulldown>;
+ pinctrl-45 = <&a4_gpio>;
+ pinctrl-46 = <&a4_gpio_pullup>;
+ pinctrl-47 = <&a4_gpio_pulldown>;
+ pinctrl-48 = <&a5_gpio>;
+ pinctrl-49 = <&a5_gpio_pullup>;
+ pinctrl-50 = <&a5_gpio_pulldown>;
+
+ d0_uart0_rxd: d0-uart0-rxd {
+ pinctrl-single,pins = <
+ /* (P4) MCU_UART0_RXD */
+ AM65X_WKUP_IOPAD(0x0044, PIN_INPUT, 4)
+ >;
+ };
+
+ d0_gpio: d0-gpio {
+ pinctrl-single,pins = <
+ /* (P4) WKUP_GPIO0_29 */
+ AM65X_WKUP_IOPAD(0x0044, PIN_INPUT, 7)
+ >;
+ };
+
+ d0_gpio_pullup: d0-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (P4) WKUP_GPIO0_29 */
+ AM65X_WKUP_IOPAD(0x0044, PIN_INPUT_PULLUP, 7)
+ >;
+ };
+
+ d0_gpio_pulldown: d0-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (P4) WKUP_GPIO0_29 */
+ AM65X_WKUP_IOPAD(0x0044, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d1_uart0_txd: d1-uart0-txd {
+ pinctrl-single,pins = <
+ /* (P5) MCU_UART0_TXD */
+ AM65X_WKUP_IOPAD(0x0048, PIN_OUTPUT, 4)
+ >;
+ };
+
+ d1_gpio: d1-gpio {
+ pinctrl-single,pins = <
+ /* (P5) WKUP_GPIO0_30 */
+ AM65X_WKUP_IOPAD(0x0048, PIN_INPUT, 7)
+ >;
+ };
+
+ d1_gpio_pullup: d1-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (P5) WKUP_GPIO0_30 */
+ AM65X_WKUP_IOPAD(0x0048, PIN_INPUT, 7)
+ >;
+ };
+
+ d1_gpio_pulldown: d1-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (P5) WKUP_GPIO0_30 */
+ AM65X_WKUP_IOPAD(0x0048, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d2_uart0_ctsn: d2-uart0-ctsn {
+ pinctrl-single,pins = <
+ /* (P1) MCU_UART0_CTSn */
+ AM65X_WKUP_IOPAD(0x004C, PIN_INPUT, 4)
+ >;
+ };
+
+ d2_gpio: d2-gpio {
+ pinctrl-single,pins = <
+ /* (P5) WKUP_GPIO0_31 */
+ AM65X_WKUP_IOPAD(0x004C, PIN_INPUT, 7)
+ >;
+ };
+
+ d2_gpio_pullup: d2-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (P5) WKUP_GPIO0_31 */
+ AM65X_WKUP_IOPAD(0x004C, PIN_INPUT, 7)
+ >;
+ };
+
+ d2_gpio_pulldown: d2-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (P5) WKUP_GPIO0_31 */
+ AM65X_WKUP_IOPAD(0x004C, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d3_uart0_rtsn: d3-uart0-rtsn {
+ pinctrl-single,pins = <
+ /* (N3) MCU_UART0_RTSn */
+ AM65X_WKUP_IOPAD(0x0054, PIN_OUTPUT, 4)
+ >;
+ };
+
+ d3_gpio: d3-gpio {
+ pinctrl-single,pins = <
+ /* (N3) WKUP_GPIO0_33 */
+ AM65X_WKUP_IOPAD(0x0054, PIN_INPUT, 7)
+ >;
+ };
+
+ d3_gpio_pullup: d3-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (N3) WKUP_GPIO0_33 */
+ AM65X_WKUP_IOPAD(0x0054, PIN_INPUT, 7)
+ >;
+ };
+
+ d3_gpio_pulldown: d3-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (N3) WKUP_GPIO0_33 */
+ AM65X_WKUP_IOPAD(0x0054, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d10_spi0_cs0: d10-spi0-cs0 {
+ pinctrl-single,pins = <
+ /* (Y4) MCU_SPI0_CS0 */
+ AM65X_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0)
+ >;
+ };
+
+ d10_gpio: d10-gpio {
+ pinctrl-single,pins = <
+ /* (Y4) WKUP_GPIO0_51 */
+ AM65X_WKUP_IOPAD(0x009c, PIN_INPUT, 7)
+ >;
+ };
+
+ d10_gpio_pullup: d10-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (Y4) WKUP_GPIO0_51 */
+ AM65X_WKUP_IOPAD(0x009c, PIN_INPUT, 7)
+ >;
+ };
+
+ d10_gpio_pulldown: d10-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (Y4) WKUP_GPIO0_51 */
+ AM65X_WKUP_IOPAD(0x009c, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d11_spi0_d0: d11-spi0-d0 {
+ pinctrl-single,pins = <
+ /* (Y3) MCU_SPI0_D0 */
+ AM65X_WKUP_IOPAD(0x0094, PIN_INPUT, 0)
+ >;
+ };
+
+ d11_gpio: d11-gpio {
+ pinctrl-single,pins = <
+ /* (Y3) WKUP_GPIO0_49 */
+ AM65X_WKUP_IOPAD(0x0094, PIN_INPUT, 7)
+ >;
+ };
+
+ d11_gpio_pullup: d11-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (Y3) WKUP_GPIO0_49 */
+ AM65X_WKUP_IOPAD(0x0094, PIN_INPUT, 7)
+ >;
+ };
+
+ d11_gpio_pulldown: d11-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (Y3) WKUP_GPIO0_49 */
+ AM65X_WKUP_IOPAD(0x0094, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d12_spi0_d1: d12-spi0-d1 {
+ pinctrl-single,pins = <
+ /* (Y2) MCU_SPI0_D1 */
+ AM65X_WKUP_IOPAD(0x0098, PIN_INPUT, 0)
+ >;
+ };
+
+ d12_gpio: d12-gpio {
+ pinctrl-single,pins = <
+ /* (Y2) WKUP_GPIO0_50 */
+ AM65X_WKUP_IOPAD(0x0098, PIN_INPUT, 7)
+ >;
+ };
+
+ d12_gpio_pullup: d12-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (Y2) WKUP_GPIO0_50 */
+ AM65X_WKUP_IOPAD(0x0098, PIN_INPUT, 7)
+ >;
+ };
+
+ d12_gpio_pulldown: d12-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (Y2) WKUP_GPIO0_50 */
+ AM65X_WKUP_IOPAD(0x0098, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d13_spi0_clk: d13-spi0-clk {
+ pinctrl-single,pins = <
+ /* (Y1) MCU_SPI0_CLK */
+ AM65X_WKUP_IOPAD(0x0090, PIN_INPUT, 0)
+ >;
+ };
+
+ d13_gpio: d13-gpio {
+ pinctrl-single,pins = <
+ /* (Y1) WKUP_GPIO0_48 */
+ AM65X_WKUP_IOPAD(0x0090, PIN_INPUT, 7)
+ >;
+ };
+
+ d13_gpio_pullup: d13-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (Y1) WKUP_GPIO0_48 */
+ AM65X_WKUP_IOPAD(0x0090, PIN_INPUT, 7)
+ >;
+ };
+
+ d13_gpio_pulldown: d13-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (Y1) WKUP_GPIO0_48 */
+ AM65X_WKUP_IOPAD(0x0090, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ a0_gpio: a0-gpio {
+ pinctrl-single,pins = <
+ /* (L6) WKUP_GPIO0_45 */
+ AM65X_WKUP_IOPAD(0x0084, PIN_INPUT, 7)
+ >;
+ };
+
+ a0_gpio_pullup: a0-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (L6) WKUP_GPIO0_45 */
+ AM65X_WKUP_IOPAD(0x0084, PIN_INPUT, 7)
+ >;
+ };
+
+ a0_gpio_pulldown: a0-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (L6) WKUP_GPIO0_45 */
+ AM65X_WKUP_IOPAD(0x0084, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ a1_gpio: a1-gpio {
+ pinctrl-single,pins = <
+ /* (M6) WKUP_GPIO0_44 */
+ AM65X_WKUP_IOPAD(0x0080, PIN_INPUT, 7)
+ >;
+ };
+
+ a1_gpio_pullup: a1-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (M6) WKUP_GPIO0_44 */
+ AM65X_WKUP_IOPAD(0x0080, PIN_INPUT, 7)
+ >;
+ };
+
+ a1_gpio_pulldown: a1-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (M6) WKUP_GPIO0_44 */
+ AM65X_WKUP_IOPAD(0x0080, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ a2_gpio: a2-gpio {
+ pinctrl-single,pins = <
+ /* (L5) WKUP_GPIO0_43 */
+ AM65X_WKUP_IOPAD(0x007C, PIN_INPUT, 7)
+ >;
+ };
+
+ a2_gpio_pullup: a2-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (L5) WKUP_GPIO0_43 */
+ AM65X_WKUP_IOPAD(0x007C, PIN_INPUT, 7)
+ >;
+ };
+
+ a2_gpio_pulldown: a2-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (L5) WKUP_GPIO0_43 */
+ AM65X_WKUP_IOPAD(0x007C, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ a3_gpio: a3-gpio {
+ pinctrl-single,pins = <
+ /* (M5) WKUP_GPIO0_39 */
+ AM65X_WKUP_IOPAD(0x006C, PIN_INPUT, 7)
+ >;
+ };
+
+ a3_gpio_pullup: a3-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (M5) WKUP_GPIO0_39 */
+ AM65X_WKUP_IOPAD(0x006C, PIN_INPUT, 7)
+ >;
+ };
+
+ a3_gpio_pulldown: a3-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (M5) WKUP_GPIO0_39 */
+ AM65X_WKUP_IOPAD(0x006C, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ a4_gpio: a4-gpio {
+ pinctrl-single,pins = <
+ /* (L2) WKUP_GPIO0_42 */
+ AM65X_WKUP_IOPAD(0x0078, PIN_INPUT, 7)
+ >;
+ };
+
+ a4_gpio_pullup: a4-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (L2) WKUP_GPIO0_42 */
+ AM65X_WKUP_IOPAD(0x0078, PIN_INPUT, 7)
+ >;
+ };
+
+ a4_gpio_pulldown: a4-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (L2) WKUP_GPIO0_42 */
+ AM65X_WKUP_IOPAD(0x0078, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ a5_gpio: a5-gpio {
+ pinctrl-single,pins = <
+ /* (N5) WKUP_GPIO0_35 */
+ AM65X_WKUP_IOPAD(0x005C, PIN_INPUT, 7)
+ >;
+ };
+
+ a5_gpio_pullup: a5-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (N5) WKUP_GPIO0_35 */
+ AM65X_WKUP_IOPAD(0x005C, PIN_INPUT_PULLUP, 7)
+ >;
+ };
+
+ a5_gpio_pulldown: a5-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (N5) WKUP_GPIO0_35 */
+ AM65X_WKUP_IOPAD(0x005C, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
pinctrl-single,pins = <
/* (AC7) WKUP_I2C0_SCL */
@@ -146,23 +565,6 @@ AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7)
>;
};
- arduino_uart_pins_default: arduino-uart-default-pins {
- pinctrl-single,pins = <
- /* (P4) MCU_UART0_RXD */
- AM65X_WKUP_IOPAD(0x0044, PIN_INPUT, 4)
- /* (P5) MCU_UART0_TXD */
- AM65X_WKUP_IOPAD(0x0048, PIN_OUTPUT, 4)
- >;
- };
-
- arduino_io_d2_to_d3_pins_default: arduino-io-d2-to-d3-default-pins {
- pinctrl-single,pins = <
- /* (P1) WKUP_GPIO0_31 */
- AM65X_WKUP_IOPAD(0x004C, PIN_OUTPUT, 7)
- /* (N3) WKUP_GPIO0_33 */
- AM65X_WKUP_IOPAD(0x0054, PIN_OUTPUT, 7)
- >;
- };
arduino_io_oe_pins_default: arduino-io-oe-default-pins {
pinctrl-single,pins = <
@@ -242,6 +644,214 @@ AM65X_WKUP_IOPAD(0x003C, PIN_OUTPUT, 7)
};
&main_pmx0 {
+ pinctrl-names =
+ "default",
+ "d4-ehrpwm0-a", "d4-gpio", "d4-gpio-pullup", "d4-gpio-pulldown",
+ "d5-ehrpwm1-a", "d5-gpio", "d5-gpio-pullup", "d5-gpio-pulldown",
+ "d6-ehrpwm2-a", "d6-gpio", "d6-gpio-pullup", "d6-gpio-pulldown",
+ "d7-ehrpwm3-a", "d7-gpio", "d7-gpio-pullup", "d7-gpio-pulldown",
+ "d8-ehrpwm4-a", "d8-gpio", "d8-gpio-pullup", "d8-gpio-pulldown",
+ "d9-ehrpwm5-a", "d9-gpio", "d9-gpio-pullup", "d9-gpio-pulldown";
+
+ pinctrl-0 = <&d4_ehrpwm0_a>;
+ pinctrl-1 = <&d4_ehrpwm0_a>;
+ pinctrl-2 = <&d4_gpio>;
+ pinctrl-3 = <&d4_gpio_pullup>;
+ pinctrl-4 = <&d4_gpio_pulldown>;
+
+ pinctrl-5 = <&d5_ehrpwm1_a>;
+ pinctrl-6 = <&d5_gpio>;
+ pinctrl-7 = <&d5_gpio_pullup>;
+ pinctrl-8 = <&d5_gpio_pulldown>;
+
+ pinctrl-9 = <&d6_ehrpwm2_a>;
+ pinctrl-10 = <&d6_gpio>;
+ pinctrl-11 = <&d6_gpio_pullup>;
+ pinctrl-12 = <&d6_gpio_pulldown>;
+
+ pinctrl-13 = <&d7_ehrpwm3_a>;
+ pinctrl-14 = <&d7_gpio>;
+ pinctrl-15 = <&d7_gpio_pullup>;
+ pinctrl-16 = <&d7_gpio_pulldown>;
+
+ pinctrl-17 = <&d8_ehrpwm4_a>;
+ pinctrl-18 = <&d8_gpio>;
+ pinctrl-19 = <&d8_gpio_pullup>;
+ pinctrl-20 = <&d8_gpio_pulldown>;
+
+ pinctrl-21 = <&d9_ehrpwm5_a>;
+ pinctrl-22 = <&d9_gpio>;
+ pinctrl-23 = <&d9_gpio_pullup>;
+ pinctrl-24 = <&d9_gpio_pulldown>;
+
+ d4_ehrpwm0_a: d4-ehrpwm0-a {
+ pinctrl-single,pins = <
+ /* (AG18) EHRPWM0_A */
+ AM65X_IOPAD(0x0084, PIN_OUTPUT, 5)
+ >;
+ };
+
+ d4_gpio: d4-gpio {
+ pinctrl-single,pins = <
+ /* (AG18) GPIO0_33 */
+ AM65X_IOPAD(0x0084, PIN_INPUT, 7)
+ >;
+ };
+
+ d4_gpio_pullup: d4-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (AG18) GPIO0_33 */
+ AM65X_IOPAD(0x0084, PIN_INPUT_PULLUP, 7)
+ >;
+ };
+
+ d4_gpio_pulldown: d4-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (AG18) GPIO0_33 */
+ AM65X_IOPAD(0x0084, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d5_ehrpwm1_a: d5-ehrpwm1-a {
+ pinctrl-single,pins = <
+ /* (AF17) EHRPWM1_A */
+ AM65X_IOPAD(0x008C, PIN_OUTPUT, 5)
+ >;
+ };
+
+ d5_gpio: d5-gpio {
+ pinctrl-single,pins = <
+ /* (AF17) GPIO0_35 */
+ AM65X_IOPAD(0x008C, PIN_INPUT, 7)
+ >;
+ };
+
+ d5_gpio_pullup: d5-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (AF17) GPIO0_35 */
+ AM65X_IOPAD(0x008C, PIN_INPUT_PULLUP, 7)
+ >;
+ };
+
+ d5_gpio_pulldown: d5-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (AF17) GPIO0_35 */
+ AM65X_IOPAD(0x008C, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d6_ehrpwm2_a: d6-ehrpwm2-a {
+ pinctrl-single,pins = <
+ /* (AH16) EHRPWM2_A */
+ AM65X_IOPAD(0x0098, PIN_OUTPUT, 5)
+ >;
+ };
+
+ d6_gpio: d6-gpio {
+ pinctrl-single,pins = <
+ /* (AH16) GPIO0_38 */
+ AM65X_IOPAD(0x0098, PIN_INPUT, 7)
+ >;
+ };
+
+ d6_gpio_pullup: d6-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (AH16) GPIO0_38 */
+ AM65X_IOPAD(0x0098, PIN_INPUT_PULLUP, 7)
+ >;
+ };
+
+ d6_gpio_pulldown: d6-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (AH16) GPIO0_38 */
+ AM65X_IOPAD(0x0098, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d7_ehrpwm3_a: d7-ehrpwm3-a {
+ pinctrl-single,pins = <
+ /* (AH15) EHRPWM3_A */
+ AM65X_IOPAD(0x00AC, PIN_OUTPUT, 5)
+ >;
+ };
+
+ d7_gpio: d7-gpio {
+ pinctrl-single,pins = <
+ /* (AH15) GPIO0_43 */
+ AM65X_IOPAD(0x00AC, PIN_INPUT, 7)
+ >;
+ };
+
+ d7_gpio_pullup: d7-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (AH15) GPIO0_43 */
+ AM65X_IOPAD(0x00AC, PIN_INPUT_PULLUP, 7)
+ >;
+ };
+
+ d7_gpio_pulldown: d7-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (AH15) GPIO0_43 */
+ AM65X_IOPAD(0x00AC, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d8_ehrpwm4_a: d8-ehrpwm4-a {
+ pinctrl-single,pins = <
+ /* (AG15) EHRPWM4_A */
+ AM65X_IOPAD(0x00C0, PIN_OUTPUT, 5)
+ >;
+ };
+
+ d8_gpio: d8-gpio {
+ pinctrl-single,pins = <
+ /* (AG15) GPIO0_48 */
+ AM65X_IOPAD(0x00C0, PIN_INPUT, 7)
+ >;
+ };
+
+ d8_gpio_pullup: d8-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (AG15) GPIO0_48 */
+ AM65X_IOPAD(0x00C0, PIN_INPUT_PULLUP, 7)
+ >;
+ };
+
+ d8_gpio_pulldown: d8-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (AG15) GPIO0_48 */
+ AM65X_IOPAD(0x00C0, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
+ d9_ehrpwm5_a: d9-ehrpwm5-a {
+ pinctrl-single,pins = <
+ /* (AD15) EHRPWM5_A */
+ AM65X_IOPAD(0x00CC, PIN_OUTPUT, 5)
+ >;
+ };
+
+ d9_gpio: d9-gpio {
+ pinctrl-single,pins = <
+ /* (AD15) GPIO0_51 */
+ AM65X_IOPAD(0x00CC, PIN_INPUT, 7)
+ >;
+ };
+
+ d9_gpio_pullup: d9-gpio-pullup {
+ pinctrl-single,pins = <
+ /* (AD15) GPIO0_51 */
+ AM65X_IOPAD(0x00CC, PIN_INPUT_PULLUP, 7)
+ >;
+ };
+
+ d9_gpio_pulldown: d9-gpio-pulldown {
+ pinctrl-single,pins = <
+ /* (AD15) GPIO0_51 */
+ AM65X_IOPAD(0x00CC, PIN_INPUT_PULLDOWN, 7)
+ >;
+ };
+
main_uart1_pins_default: main-uart1-default-pins {
pinctrl-single,pins = <
AM65X_IOPAD(0x0174, PIN_INPUT, 6) /* (AE23) UART1_RXD */
@@ -283,17 +893,6 @@ AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */
>;
};
- arduino_io_d4_to_d9_pins_default: arduino-io-d4-to-d9-default-pins {
- pinctrl-single,pins = <
- AM65X_IOPAD(0x0084, PIN_OUTPUT, 7) /* (AG18) GPIO0_33 */
- AM65X_IOPAD(0x008C, PIN_OUTPUT, 7) /* (AF17) GPIO0_35 */
- AM65X_IOPAD(0x0098, PIN_OUTPUT, 7) /* (AH16) GPIO0_38 */
- AM65X_IOPAD(0x00AC, PIN_OUTPUT, 7) /* (AH15) GPIO0_43 */
- AM65X_IOPAD(0x00C0, PIN_OUTPUT, 7) /* (AG15) GPIO0_48 */
- AM65X_IOPAD(0x00CC, PIN_OUTPUT, 7) /* (AD15) GPIO0_51 */
- >;
- };
-
dss_vout1_pins_default: dss-vout1-default-pins {
pinctrl-single,pins = <
AM65X_IOPAD(0x0000, PIN_OUTPUT, 1) /* VOUT1_DATA0 */
@@ -370,13 +969,9 @@ &main_uart1 {
&mcu_uart0 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&arduino_uart_pins_default>;
};
&main_gpio0 {
- pinctrl-names = "default";
- pinctrl-0 = <&arduino_io_d4_to_d9_pins_default>;
gpio-line-names =
"main_gpio0-base", "", "", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "", "", "",
@@ -389,7 +984,6 @@ &main_gpio0 {
&wkup_gpio0 {
pinctrl-names = "default";
pinctrl-0 =
- <&arduino_io_d2_to_d3_pins_default>,
<&arduino_i2c_aio_switch_pins_default>,
<&arduino_io_oe_pins_default>,
<&push_button_pins_default>,
@@ -572,9 +1166,6 @@ &usb1 {
&mcu_spi0 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mcu_spi0_pins_default>;
-
#address-cells = <1>;
#size-cells = <0>;
ti,pindir-d0-out-d1-in;
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
index 774eb14ac907..8301c35c31b3 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
@@ -66,9 +66,7 @@ AM65X_IOPAD(0x001c, PIN_INPUT_PULLUP, 7) /* (C23) GPIO1_89 */
&main_gpio0 {
pinctrl-names = "default";
- pinctrl-0 =
- <&main_m2_pcie_mux_control>,
- <&arduino_io_d4_to_d9_pins_default>;
+ pinctrl-0 = <&main_m2_pcie_mux_control>;
};
&main_gpio1 {
--
2.35.3
From: Su Bao Cheng <[email protected]>
Make the m.2 power control pin also available on miniPCIE variants.
This can fix some miniPCIE card hang issue, by forcing a power on reset
during boot.
Signed-off-by: Baocheng Su <[email protected]>
---
.../arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi | 4 +++-
arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi | 11 +++++++++++
.../boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts | 8 +-------
3 files changed, 15 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
index e9419c4fe605..e9b57b87e42e 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
@@ -20,7 +20,9 @@ AM65X_IOPAD(0x01e0, PIN_OUTPUT, 7)
&main_gpio1 {
pinctrl-names = "default";
- pinctrl-0 = <&cp2102n_reset_pin_default>;
+ pinctrl-0 =
+ <&main_pcie_enable_pins_default>,
+ <&cp2102n_reset_pin_default>;
gpio-line-names =
"", "", "", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "", "", "",
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 74c4accff4b7..53bd296ba310 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -852,6 +852,12 @@ AM65X_IOPAD(0x00CC, PIN_INPUT_PULLDOWN, 7)
>;
};
+ main_pcie_enable_pins_default: main-pcie-enable-default-pins {
+ pinctrl-single,pins = <
+ AM65X_IOPAD(0x01c4, PIN_INPUT_PULLUP, 7) /* (AH13) GPIO1_17 */
+ >;
+ };
+
main_uart1_pins_default: main-uart1-default-pins {
pinctrl-single,pins = <
AM65X_IOPAD(0x0174, PIN_INPUT, 6) /* (AE23) UART1_RXD */
@@ -981,6 +987,11 @@ &main_gpio0 {
"", "IO9";
};
+&main_gpio1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_pcie_enable_pins_default>;
+};
+
&wkup_gpio0 {
pinctrl-names = "default";
pinctrl-0 =
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
index 8301c35c31b3..bd6f2e696e94 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
@@ -27,12 +27,6 @@ &mcu_r5fss0 {
};
&main_pmx0 {
- main_m2_enable_pins_default: main-m2-enable-default-pins {
- pinctrl-single,pins = <
- AM65X_IOPAD(0x01c4, PIN_INPUT_PULLUP, 7) /* (AH13) GPIO1_17 */
- >;
- };
-
main_bkey_pcie_reset: main-bkey-pcie-reset-default-pins {
pinctrl-single,pins = <
AM65X_IOPAD(0x01bc, PIN_OUTPUT_PULLUP, 7) /* (AG13) GPIO1_15 */
@@ -72,7 +66,7 @@ &main_gpio0 {
&main_gpio1 {
pinctrl-names = "default";
pinctrl-0 =
- <&main_m2_enable_pins_default>,
+ <&main_pcie_enable_pins_default>,
<&main_pmx0_m2_config_pins_default>,
<&main_pmx1_m2_config_pins_default>,
<&cp2102n_reset_pin_default>;
--
2.35.3
From: Jan Kiszka <[email protected]>
Lost while dropping them from the common dtsi.
Fixes: ffc449e016e2 ("arm64: dts: ti: k3-am65: Drop aliases")
Signed-off-by: Jan Kiszka <[email protected]>
---
arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index ba1c14a54acf..b849648d51f9 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -14,6 +14,16 @@
/ {
aliases {
+ serial0 = &wkup_uart0;
+ serial1 = &mcu_uart0;
+ serial2 = &main_uart0;
+ serial3 = &main_uart1;
+ i2c0 = &wkup_i2c0;
+ i2c1 = &mcu_i2c0;
+ i2c2 = &main_i2c0;
+ i2c3 = &main_i2c1;
+ i2c4 = &main_i2c2;
+ i2c5 = &main_i2c3;
spi0 = &mcu_spi0;
mmc0 = &sdhci1;
mmc1 = &sdhci0;
--
2.35.3
From: Jan Kiszka <[email protected]>
Add the required nodes to enable ICSSG SR2.0 based prueth networking.
As the driver still needs to be extended for SR1.0 support, keep related
nodes disabled on PG1 devices.
Signed-off-by: Jan Kiszka <[email protected]>
---
.../dts/ti/k3-am65-iot2050-common-pg1.dtsi | 10 +-
.../boot/dts/ti/k3-am65-iot2050-common.dtsi | 132 ++++++++++++++++++
2 files changed, 141 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
index 51f902fa35a7..1d1979859583 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * Copyright (c) Siemens AG, 2021
+ * Copyright (c) Siemens AG, 2021-2023
*
* Authors:
* Jan Kiszka <[email protected]>
@@ -44,3 +44,11 @@ &tx_pru2_0 {
&tx_pru2_1 {
status = "disabled";
};
+
+&icssg0_eth {
+ status = "disabled";
+};
+
+&icssg0_mdio {
+ status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index bc77ba58d8f9..1a558851ea96 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -11,6 +11,7 @@
#include "k3-am654.dtsi"
#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/net/ti-dp83867.h>
/ {
aliases {
@@ -27,6 +28,8 @@ aliases {
spi0 = &mcu_spi0;
mmc0 = &sdhci1;
mmc1 = &sdhci0;
+ ethernet1 = &icssg0_emac0;
+ ethernet2 = &icssg0_emac1;
};
chosen {
@@ -111,6 +114,80 @@ dp_refclk: clock {
#clock-cells = <0>;
clock-frequency = <19200000>;
};
+
+ /* Dual Ethernet application node on PRU-ICSSG0 */
+ icssg0_eth: icssg0-eth {
+ compatible = "ti,am654-icssg-prueth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&icssg0_rgmii_pins_default>;
+ sram = <&msmc_ram>;
+
+ ti,prus = <&pru0_0>, <&rtu0_0>, <&tx_pru0_0>,
+ <&pru0_1>, <&rtu0_1>, <&tx_pru0_1>;
+ firmware-name = "ti-pruss/am65x-sr2-pru0-prueth-fw.elf",
+ "ti-pruss/am65x-sr2-rtu0-prueth-fw.elf",
+ "ti-pruss/am65x-sr2-txpru0-prueth-fw.elf",
+ "ti-pruss/am65x-sr2-pru1-prueth-fw.elf",
+ "ti-pruss/am65x-sr2-rtu1-prueth-fw.elf",
+ "ti-pruss/am65x-sr2-txpru1-prueth-fw.elf";
+
+ ti,pruss-gp-mux-sel = <2>, /* MII mode */
+ <2>,
+ <2>,
+ <2>, /* MII mode */
+ <2>,
+ <2>;
+
+ ti,mii-g-rt = <&icssg0_mii_g_rt>;
+ ti,mii-rt = <&icssg0_mii_rt>;
+ ti,iep = <&icssg0_iep0>, <&icssg0_iep1>;
+
+ interrupt-parent = <&icssg0_intc>;
+ interrupts = <24 0 2>, <25 1 3>;
+ interrupt-names = "tx_ts0", "tx_ts1";
+
+ dmas = <&main_udmap 0xc100>, /* egress slice 0 */
+ <&main_udmap 0xc101>, /* egress slice 0 */
+ <&main_udmap 0xc102>, /* egress slice 0 */
+ <&main_udmap 0xc103>, /* egress slice 0 */
+ <&main_udmap 0xc104>, /* egress slice 1 */
+ <&main_udmap 0xc105>, /* egress slice 1 */
+ <&main_udmap 0xc106>, /* egress slice 1 */
+ <&main_udmap 0xc107>, /* egress slice 1 */
+
+ <&main_udmap 0x4100>, /* ingress slice 0 */
+ <&main_udmap 0x4101>, /* ingress slice 1 */
+ <&main_udmap 0x4102>, /* mgmnt rsp slice 0 */
+ <&main_udmap 0x4103>; /* mgmnt rsp slice 1 */
+ dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
+ "tx1-0", "tx1-1", "tx1-2", "tx1-3",
+ "rx0", "rx1",
+ "rxmgm0", "rxmgm1";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ icssg0_emac0: port@0 {
+ reg = <0>;
+ phy-handle = <&icssg0_eth0_phy>;
+ phy-mode = "rgmii-id";
+ ti,syscon-rgmii-delay = <&scm_conf 0x4100>;
+ ti,half-duplex-capable;
+ /* Filled in by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ };
+
+ icssg0_emac1: port@1 {
+ reg = <1>;
+ phy-handle = <&icssg0_eth1_phy>;
+ phy-mode = "rgmii-id";
+ ti,syscon-rgmii-delay = <&scm_conf 0x4104>;
+ ti,half-duplex-capable;
+ /* Filled in by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ };
+ };
+ };
};
&wkup_pmx0 {
@@ -944,6 +1021,43 @@ AM65X_IOPAD(0x0074, PIN_INPUT, 5) /* (T27) I2C2_SCL */
AM65X_IOPAD(0x0070, PIN_INPUT, 5) /* (R25) I2C2_SDA */
>;
};
+
+ icssg0_mdio_pins_default: icssg0-mdio-pins-default {
+ pinctrl-single,pins = <
+ AM65X_IOPAD(0x0294, PIN_INPUT, 0) /* (AE26) PRG0_MDIO0_MDIO */
+ AM65X_IOPAD(0x0298, PIN_OUTPUT, 0) /* (AE28) PRG0_MDIO0_MDC */
+ >;
+ };
+
+ icssg0_rgmii_pins_default: icssg0-rgmii-pins-default {
+ pinctrl-single,pins = <
+ AM65X_IOPAD(0x0244, PIN_INPUT, 2) /* (AB28) PRG0_PRU1_GPO0.PRG0_RGMII2_RD0 */
+ AM65X_IOPAD(0x0248, PIN_INPUT, 2) /* (AC28) PRG0_PRU1_GPO1.PRG0_RGMII2_RD1 */
+ AM65X_IOPAD(0x024c, PIN_INPUT, 2) /* (AC27) PRG0_PRU1_GPO2.PRG0_RGMII2_RD2 */
+ AM65X_IOPAD(0x0250, PIN_INPUT, 2) /* (AB26) PRG0_PRU1_GPO3.PRG0_RGMII2_RD3 */
+ AM65X_IOPAD(0x0274, PIN_OUTPUT, 2) /* (AC25) PRG0_PRU1_GPO12.PRG0_RGMII2_TD0 */
+ AM65X_IOPAD(0x0278, PIN_OUTPUT, 2) /* (AD25) PRG0_PRU1_GPO13.PRG0_RGMII2_TD1 */
+ AM65X_IOPAD(0x027c, PIN_OUTPUT, 2) /* (AD24) PRG0_PRU1_GPO14.PRG0_RGMII2_TD2 */
+ AM65X_IOPAD(0x0280, PIN_OUTPUT, 2) /* (AE27) PRG0_PRU1_GPO15.PRG0_RGMII2_TD3 */
+ AM65X_IOPAD(0x0284, PIN_INPUT, 2) /* (AC24) PRG0_PRU1_GPO16.PRG0_RGMII2_TXC */
+ AM65X_IOPAD(0x0270, PIN_OUTPUT, 2) /* (AB24) PRG0_PRU1_GPO11.PRG0_RGMII2_TX_CTL */
+ AM65X_IOPAD(0x025c, PIN_INPUT, 2) /* (AB27) PRG0_PRU1_GPO6.PRG0_RGMII2_RXC */
+ AM65X_IOPAD(0x0254, PIN_INPUT, 2) /* (AA25) PRG0_PRU1_GPO4.PRG0_RGMII2_RX_CTL */
+
+ AM65X_IOPAD(0x01f4, PIN_INPUT, 2) /* (V24) PRG0_PRU0_GPO0.PRG0_RGMII1_RD0 */
+ AM65X_IOPAD(0x01f8, PIN_INPUT, 2) /* (W25) PRG0_PRU0_GPO1.PRG0_RGMII1_RD1 */
+ AM65X_IOPAD(0x01fc, PIN_INPUT, 2) /* (W24) PRG0_PRU0_GPO2.PRG0_RGMII1_RD2 */
+ AM65X_IOPAD(0x0200, PIN_INPUT, 2) /* (AA27) PRG0_PRU0_GPO3.PRG0_RGMII1_RD3 */
+ AM65X_IOPAD(0x0224, PIN_OUTPUT, 2) /* (AD27) PRG0_PRU0_GPO12.PRG0_RGMII1_TD0 */
+ AM65X_IOPAD(0x0228, PIN_OUTPUT, 2) /* (AC26) PRG0_PRU0_GPO13.PRG0_RGMII1_TD1 */
+ AM65X_IOPAD(0x022c, PIN_OUTPUT, 2) /* (AD26) PRG0_PRU0_GPO14.PRG0_RGMII1_TD2 */
+ AM65X_IOPAD(0x0230, PIN_OUTPUT, 2) /* (AA24) PRG0_PRU0_GPO15.PRG0_RGMII1_TD3 */
+ AM65X_IOPAD(0x0234, PIN_INPUT, 2) /* (AD28) PRG0_PRU0_GPO16.PRG0_RGMII1_TXC */
+ AM65X_IOPAD(0x0220, PIN_OUTPUT, 2) /* (AB25) PRG0_PRU0_GPO11.PRG0_RGMII1_TX_CTL */
+ AM65X_IOPAD(0x020c, PIN_INPUT, 2) /* (Y25) PRG0_PRU0_GPO6.PRG0_RGMII1_RXC */
+ AM65X_IOPAD(0x0204, PIN_INPUT, 2) /* (Y24) PRG0_PRU0_GPO4.PRG0_RGMII1_RX_CTL */
+ >;
+ };
};
&main_pmx1 {
@@ -1322,3 +1436,21 @@ &mcu_r5fss0_core1 {
<&mcu_r5fss0_core1_memory_region>;
mboxes = <&mailbox0_cluster1>, <&mbox_mcu_r5fss0_core1>;
};
+
+&icssg0_mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&icssg0_mdio_pins_default>;
+
+ icssg0_eth0_phy: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+
+ icssg0_eth1_phy: ethernet-phy@1 {
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+};
--
2.35.3
On 15:34-20231027, Jan Kiszka wrote:
> From: Su Bao Cheng <[email protected]>
>
> Make the m.2 power control pin also available on miniPCIE variants.
>
> This can fix some miniPCIE card hang issue, by forcing a power on reset
> during boot.
>
> Signed-off-by: Baocheng Su <[email protected]>
> ---
Jan - please Sign-off for the carried chain..
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
On 15:34-20231027, Jan Kiszka wrote:
> From: Benedikt Niedermayr <[email protected]>
>
> Add multiple device tree nodes in order to support
> runtime pinmuxing via debugfs.
>
> All nodes are added to the pinctrl device node,
> since they are now belonging to multiple interfaces now.
>
> Note: Pinconf is also handled by debugfs-pinmux. This is possible since
> pinconf and pinmux accessing the same 32-Bit register and setting the
> function mask to 32-Bit allows writes to the whole register.
>
> Signed-off-by: Benedikt Niedermayr <[email protected]>
Your sign off is missing here Jan.
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
On 27.10.23 15:43, Nishanth Menon wrote:
> On 15:34-20231027, Jan Kiszka wrote:
>> From: Su Bao Cheng <[email protected]>
>>
>> Make the m.2 power control pin also available on miniPCIE variants.
>>
>> This can fix some miniPCIE card hang issue, by forcing a power on reset
>> during boot.
>>
>> Signed-off-by: Baocheng Su <[email protected]>
>> ---
>
> Jan - please Sign-off for the carried chain..
>
Sure, can do. Was intentionally not doing that because I somewhere
picked up that this is not desired.
Jan
--
Siemens AG, Technology
Linux Expert Center
On 15:45-20231027, Jan Kiszka wrote:
> On 27.10.23 15:43, Nishanth Menon wrote:
> > On 15:34-20231027, Jan Kiszka wrote:
> >> From: Su Bao Cheng <[email protected]>
> >>
> >> Make the m.2 power control pin also available on miniPCIE variants.
> >>
> >> This can fix some miniPCIE card hang issue, by forcing a power on reset
> >> during boot.
> >>
> >> Signed-off-by: Baocheng Su <[email protected]>
> >> ---
> >
> > Jan - please Sign-off for the carried chain..
> >
>
> Sure, can do. Was intentionally not doing that because I somewhere
> picked up that this is not desired.
Hmm... Documentation/process/submitting-patches.rst
Signed-off-by: must always be that of the developer submitting the
patch. --> I assume you are this ;).
Signed-off-by: First Co-Author <[email protected]>
Signed-off-by: Second Co-Author <[email protected]>
Signed-off-by: From Author <[email protected]>
Signed-off-by: Random Co-Author <[email protected]>
Signed-off-by: From Author <[email protected]>
Signed-off-by: Submitting Co-Author <[email protected]>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
On Fri, Oct 27, 2023 at 03:34:36PM +0200, Jan Kiszka wrote:
> From: Jan Kiszka <[email protected]>
>
> On the Siemens IOT2050 devices, the SPI controller wired to the Arduino
> connector is normally driven by userspace. Introduce a binding for use
> by spidev.
What's spidev? Not a h/w device...
>
> Signed-off-by: Jan Kiszka <[email protected]>
> ---
> Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
> index 430a814f64a5..01b9f36afcd5 100644
> --- a/Documentation/devicetree/bindings/trivial-devices.yaml
> +++ b/Documentation/devicetree/bindings/trivial-devices.yaml
> @@ -349,6 +349,8 @@ properties:
> - silabs,si3210
> # Relative Humidity and Temperature Sensors
> - silabs,si7020
> + # Siemens IOT2050: SPI interface on Arduino connector
> + - siemens,iot2050-arduino-spi
How is this specific to your board? Presumably, an 'Arduino connector'
is a somewhat standard interface, right? If every board with an Arduino
connector adds a compatible, this doesn't scale.
A connector is what you should be describing, but I imagine it is not
just SPI. Here's some past discussions[1][2] on the need for connector
bindings.
Rob
[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/CAL_JsqK2DKPbaFvUPSU2E7oh1_pryrRXPMg8OASmK722jmznwA@mail.gmail.com/
On 30.10.23 17:43, Rob Herring wrote:
> On Fri, Oct 27, 2023 at 03:34:36PM +0200, Jan Kiszka wrote:
>> From: Jan Kiszka <[email protected]>
>>
>> On the Siemens IOT2050 devices, the SPI controller wired to the Arduino
>> connector is normally driven by userspace. Introduce a binding for use
>> by spidev.
>
> What's spidev? Not a h/w device...
>
>
>>
>> Signed-off-by: Jan Kiszka <[email protected]>
>> ---
>> Documentation/devicetree/bindings/trivial-devices.yaml | 2 ++
>> 1 file changed, 2 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml
>> index 430a814f64a5..01b9f36afcd5 100644
>> --- a/Documentation/devicetree/bindings/trivial-devices.yaml
>> +++ b/Documentation/devicetree/bindings/trivial-devices.yaml
>> @@ -349,6 +349,8 @@ properties:
>> - silabs,si3210
>> # Relative Humidity and Temperature Sensors
>> - silabs,si7020
>> + # Siemens IOT2050: SPI interface on Arduino connector
>> + - siemens,iot2050-arduino-spi
>
> How is this specific to your board? Presumably, an 'Arduino connector'
> is a somewhat standard interface, right? If every board with an Arduino
> connector adds a compatible, this doesn't scale.
>
> A connector is what you should be describing, but I imagine it is not
> just SPI. Here's some past discussions[1][2] on the need for connector
> bindings.
Right, we are not alone with this modelling problem on our board. The
code talking to the SPI devices is inside applications, the kernel just
needs to pave the way to the interface. However, you can't define that
path without bending of the DT. This is specific to at least SPI, maybe
some other buses without probing as well.
If this were a PCI device, no problem: tell vfio-pci or uio_pci_generic
to be responsible as well (add IDs on the fly), bind bind any of them
and then let userspace handle things. Same why to go back to an
in-kernel driver. No bothering of the DT regarding how the final device
is driven.
Jan
--
Siemens AG, Technology
Linux Expert Center