Change the comptiable for support of multi-platform
Add description for reg
Add description for source_cg
Add description for mediatek,latch-ck
Note that source_cg and mediatek,latch-ck are optional for some projects,
eg, MT2701 do not have source_cg, and MT2712 do not need
mediatek,latch-ck
Signed-off-by: Chaotian Jing <[email protected]>
---
Documentation/devicetree/bindings/mmc/mtk-sd.txt | 13 ++++++++++---
1 file changed, 10 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
index 4182ea3..b934a29 100644
--- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt
+++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
@@ -7,10 +7,15 @@ This file documents differences between the core properties in mmc.txt
and the properties used by the msdc driver.
Required properties:
-- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc"
+- compatible: value should be either of the following.
+ "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
+ "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
+ "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
+ "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
+- reg: physical base address of the controller and length
- interrupts: Should contain MSDC interrupt number
-- clocks: MSDC source clock, HCLK
-- clock-names: "source", "hclk"
+- clocks: MSDC source clock, HCLK, source_cg
+- clock-names: "source", "hclk", "source_cg"
- pinctrl-names: should be "default", "state_uhs"
- pinctrl-0: should contain default/high speed pin ctrl
- pinctrl-1: should contain uhs mode pin ctrl
@@ -30,6 +35,8 @@ Optional properties:
- mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection
If present,HS400 command responses are sampled on rising edges.
If not present,HS400 command responses are sampled on falling edges.
+- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
+ error caused by stop clock(fifo full)
Examples:
mmc0: mmc@11230000 {
--
1.8.1.1.dirty
On 09/22/2017 02:03 PM, Chaotian Jing wrote:
> Change the comptiable for support of multi-platform
> Add description for reg
> Add description for source_cg
> Add description for mediatek,latch-ck
> Note that source_cg and mediatek,latch-ck are optional for some projects,
> eg, MT2701 do not have source_cg, and MT2712 do not need
> mediatek,latch-ck
>
> Signed-off-by: Chaotian Jing <[email protected]>
> ---
> Documentation/devicetree/bindings/mmc/mtk-sd.txt | 13 ++++++++++---
> 1 file changed, 10 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> index 4182ea3..b934a29 100644
> --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> @@ -7,10 +7,15 @@ This file documents differences between the core properties in mmc.txt
> and the properties used by the msdc driver.
>
> Required properties:
> -- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc"
> +- compatible: value should be either of the following.
> + "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
> + "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
> + "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
> + "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
NAK, this has to be:
You have to add the fallback comatible ("mediatek,mt8135-mmc") to the binding
description as otherwise the driver does not get probed.
Regards,
Matthias
> +- reg: physical base address of the controller and length
> - interrupts: Should contain MSDC interrupt number
> -- clocks: MSDC source clock, HCLK
> -- clock-names: "source", "hclk"
> +- clocks: MSDC source clock, HCLK, source_cg
> +- clock-names: "source", "hclk", "source_cg"
> - pinctrl-names: should be "default", "state_uhs"
> - pinctrl-0: should contain default/high speed pin ctrl
> - pinctrl-1: should contain uhs mode pin ctrl
> @@ -30,6 +35,8 @@ Optional properties:
> - mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection
> If present,HS400 command responses are sampled on rising edges.
> If not present,HS400 command responses are sampled on falling edges.
> +- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
> + error caused by stop clock(fifo full)
>
> Examples:
> mmc0: mmc@11230000 {
>
On Fri, 2017-09-29 at 13:11 +0200, Matthias Brugger wrote:
>
> On 09/22/2017 02:03 PM, Chaotian Jing wrote:
> > Change the comptiable for support of multi-platform
> > Add description for reg
> > Add description for source_cg
> > Add description for mediatek,latch-ck
> > Note that source_cg and mediatek,latch-ck are optional for some projects,
> > eg, MT2701 do not have source_cg, and MT2712 do not need
> > mediatek,latch-ck
> >
> > Signed-off-by: Chaotian Jing <[email protected]>
> > ---
> > Documentation/devicetree/bindings/mmc/mtk-sd.txt | 13 ++++++++++---
> > 1 file changed, 10 insertions(+), 3 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> > index 4182ea3..b934a29 100644
> > --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> > +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> > @@ -7,10 +7,15 @@ This file documents differences between the core properties in mmc.txt
> > and the properties used by the msdc driver.
> >
> > Required properties:
> > -- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc"
> > +- compatible: value should be either of the following.
> > + "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
> > + "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
> > + "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
> > + "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
>
> NAK, this has to be:
> You have to add the fallback compatible ("mediatek,mt8135-mmc") to the binding
> description as otherwise the driver does not get probed.
>
> Regards,
> Matthias
Thanks for your comments, will add the fallback compatible
("mediatek,mt8135-mmc") to the binding in this patch.
but, is possible to remove the fallback compatible at next patch ?
eg, following patches will modify the driver like below:
static const struct of_device_id msdc_of_ids[] = {
{ .compatible = "mediatek,mt8135-mmc", .data = &mt8135_compat},
{ .compatible = "mediatek,mt8173-mmc", .data = &mt8173_compat},
};
then, there is no probe issue and remove the fallback compatible.
Thx!
>
> > +- reg: physical base address of the controller and length
> > - interrupts: Should contain MSDC interrupt number
> > -- clocks: MSDC source clock, HCLK
> > -- clock-names: "source", "hclk"
> > +- clocks: MSDC source clock, HCLK, source_cg
> > +- clock-names: "source", "hclk", "source_cg"
> > - pinctrl-names: should be "default", "state_uhs"
> > - pinctrl-0: should contain default/high speed pin ctrl
> > - pinctrl-1: should contain uhs mode pin ctrl
> > @@ -30,6 +35,8 @@ Optional properties:
> > - mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection
> > If present,HS400 command responses are sampled on rising edges.
> > If not present,HS400 command responses are sampled on falling edges.
> > +- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
> > + error caused by stop clock(fifo full)
> >
> > Examples:
> > mmc0: mmc@11230000 {
> >