From: Ondrej Jirman <[email protected]>
This is driver for ANX7688 USB-C HDMI, with flashing and debugging
features removed. ANX7688 is rather criticial piece on PinePhone,
there's no display and no battery charging without it.
There's likely more work to be done here, but having basic support
in mainline is needed to be able to work on the other stuff
(networking, cameras, power management).
Signed-off-by: Ondrej Jirman <[email protected]>
Signed-off-by: Martijn Braam <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Pavel Machek <[email protected]>
diff --git a/drivers/usb/typec/Kconfig b/drivers/usb/typec/Kconfig
index 2f80c2792dbd..982b7c444a1f 100644
--- a/drivers/usb/typec/Kconfig
+++ b/drivers/usb/typec/Kconfig
@@ -64,6 +65,17 @@ config TYPEC_ANX7411
If you choose to build this driver as a dynamically linked module, the
module will be called anx7411.ko.
+config TYPEC_ANX7688
+ tristate "Analogix ANX7688 Type-C DRP Port controller and mux driver"
+ depends on I2C
+ depends on USB_ROLE_SWITCH
+ help
+ Say Y or M here if your system has Analogix ANX7688 Type-C Bridge
+ controller driver.
+
+ If you choose to build this driver as a dynamically linked module, the
+ module will be called anx7688.ko.
+
config TYPEC_RT1719
tristate "Richtek RT1719 Sink Only Type-C controller driver"
depends on USB_ROLE_SWITCH || !USB_ROLE_SWITCH
diff --git a/drivers/usb/typec/Makefile b/drivers/usb/typec/Makefile
index 7a368fea61bc..3f8ff94ad294 100644
--- a/drivers/usb/typec/Makefile
+++ b/drivers/usb/typec/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_TYPEC_TCPM) += tcpm/
obj-$(CONFIG_TYPEC_UCSI) += ucsi/
obj-$(CONFIG_TYPEC_TPS6598X) += tipd/
obj-$(CONFIG_TYPEC_ANX7411) += anx7411.o
+obj-$(CONFIG_TYPEC_ANX7688) += anx7688.o
obj-$(CONFIG_TYPEC_HD3SS3220) += hd3ss3220.o
obj-$(CONFIG_TYPEC_STUSB160X) += stusb160x.o
obj-$(CONFIG_TYPEC_RT1719) += rt1719.o
diff --git a/drivers/usb/typec/anx7688.c b/drivers/usb/typec/anx7688.c
new file mode 100644
index 000000000000..9b693c9fd085
--- /dev/null
+++ b/drivers/usb/typec/anx7688.c
@@ -0,0 +1,1866 @@
+/*
+ * ANX7688 USB-C HDMI bridge/PD driver
+ *
+ * Warning, this driver is somewhat PinePhone specific.
+ *
+ * How this works:
+ * - this driver allows to program firmware into ANX7688 EEPROM, and
+ * initialize it
+ * - it then communicates with the firmware running on the OCM (on-chip
+ * microcontroller)
+ * - it detects whether there is cable plugged in or not and powers
+ * up or down the ANX7688 based on that
+ * - when the cable is connected the firmware on the OCM will handle
+ * the detection of the nature of the device on the other end
+ * of the USB-C cable
+ * - this driver then communicates with the USB phy to let it swap
+ * data roles accordingly
+ * - it also enables VBUS and VCONN regulators as appropriate
+ * - USB phy driver (Allwinner) needs to know whether to switch to
+ * device or host mode, or whether to turn off
+ * - when the firmware detects SRC.1.5A or SRC.3.0A via CC pins
+ * or something else via PD, it notifies this driver via software
+ * interrupt and this driver will determine how to update the TypeC
+ * port status and what input current limit is appropriate
+ * - input current limit determination happens 500ms after cable
+ * insertion or hard reset (delay is necessary to determine whether
+ * the remote end is PD capable or not)
+ * - this driver tells to the PMIC driver that the input current limit
+ * needs to be changed
+ * - this driver also monitors PMIC status and re-sets the input current
+ * limit if it changes for some reason (due to PMIC internal decision
+ * making) (this is disabled for now)
+ *
+ * ANX7688 FW behavior as observed:
+ *
+ * - DO NOT SET MORE THAN 1 SINK CAPABILITY! Firmware will ignore what
+ * you set and send hardcoded PDO_BATT 5-21V 30W message!
+ *
+ * Product brief:
+ * https://www.analogix.com/en/system/files/AA-002281-PB-6-ANX7688_Product_Brief_0.pdf
+ * Development notes:
+ * https://xnux.eu/devices/feature/anx7688.html
+ */
+
+#define DEBUG
+
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/extcon-provider.h>
+#include <linux/firmware.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irqreturn.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/power_supply.h>
+#include <linux/regulator/consumer.h>
+#include <linux/usb/pd.h>
+#include <linux/usb/role.h>
+#include <linux/usb/typec.h>
+
+/* firmware regs */
+
+#define ANX7688_REG_VBUS_OFF_DELAY_TIME 0x22
+#define ANX7688_REG_FEATURE_CTRL 0x27
+#define ANX7688_REG_EEPROM_LOAD_STATUS1 0x11
+#define ANX7688_REG_EEPROM_LOAD_STATUS0 0x12
+#define ANX7688_REG_FW_VERSION1 0x15
+#define ANX7688_REG_FW_VERSION0 0x16
+
+#define ANX7688_EEPROM_FW_LOADED 0x01
+
+#define ANX7688_REG_STATUS_INT_MASK 0x17
+#define ANX7688_REG_STATUS_INT 0x28
+#define ANX7688_IRQS_RECEIVED_MSG BIT(0)
+#define ANX7688_IRQS_RECEIVED_ACK BIT(1)
+#define ANX7688_IRQS_VCONN_CHANGE BIT(2)
+#define ANX7688_IRQS_VBUS_CHANGE BIT(3)
+#define ANX7688_IRQS_CC_STATUS_CHANGE BIT(4)
+#define ANX7688_IRQS_DATA_ROLE_CHANGE BIT(5)
+
+#define ANX7688_REG_STATUS 0x29
+#define ANX7688_VCONN_STATUS BIT(2) /* 0 = off 1 = on */
+#define ANX7688_VBUS_STATUS BIT(3) /* 0 = off 1 = on */
+#define ANX7688_DATA_ROLE_STATUS BIT(5) /* 0 = device 1 = host */
+
+#define ANX7688_REG_CC_STATUS 0x2a
+#define ANX7688_REG_TRY_UFP_TIMER 0x23
+#define ANX7688_REG_TIME_CTRL 0x24
+
+#define ANX7688_REG_MAX_VOLTAGE 0x1b
+#define ANX7688_REG_MAX_POWER 0x1c
+#define ANX7688_REG_MIN_POWER 0x1d
+#define ANX7688_REG_MAX_VOLTAGE_STATUS 0x1e
+#define ANX7688_REG_MAX_POWER_STATUS 0x1f
+
+#define ANX7688_SOFT_INT_MASK 0x7f
+
+/* tcpc regs */
+
+#define ANX7688_TCPC_REG_VENDOR_ID0 0x00
+#define ANX7688_TCPC_REG_VENDOR_ID1 0x01
+#define ANX7688_TCPC_REG_ALERT0 0x10
+#define ANX7688_TCPC_REG_ALERT1 0x11
+#define ANX7688_TCPC_REG_ALERT_MASK0 0x12
+#define ANX7688_TCPC_REG_ALERT_MASK1 0x13
+#define ANX7688_TCPC_REG_INTERFACE_SEND 0x30
+#define ANX7688_TCPC_REG_INTERFACE_RECV 0x51
+
+/* hw regs */
+
+#define ANX7688_REG_IRQ_EXT_SOURCE0 0x3e
+#define ANX7688_REG_IRQ_EXT_SOURCE1 0x4e
+#define ANX7688_REG_IRQ_EXT_SOURCE2 0x4f
+#define ANX7688_REG_IRQ_EXT_MASK0 0x3b
+#define ANX7688_REG_IRQ_EXT_MASK1 0x3c
+#define ANX7688_REG_IRQ_EXT_MASK2 0x3d
+#define ANX7688_REG_IRQ_SOURCE0 0x54
+#define ANX7688_REG_IRQ_SOURCE1 0x55
+#define ANX7688_REG_IRQ_SOURCE2 0x56
+#define ANX7688_REG_IRQ_MASK0 0x57
+#define ANX7688_REG_IRQ_MASK1 0x58
+#define ANX7688_REG_IRQ_MASK2 0x59
+
+#define ANX7688_IRQ2_SOFT_INT BIT(2)
+
+#define ANX7688_REG_USBC_RESET_CTRL 0x05
+#define ANX7688_USBC_RESET_CTRL_OCM_RESET BIT(4)
+
+/* ocm messages */
+
+#define ANX7688_OCM_MSG_PWR_SRC_CAP 0x00
+#define ANX7688_OCM_MSG_PWR_SNK_CAP 0x01
+#define ANX7688_OCM_MSG_DP_SNK_IDENTITY 0x02
+#define ANX7688_OCM_MSG_SVID 0x03
+#define ANX7688_OCM_MSG_GET_DP_SNK_CAP 0x04
+#define ANX7688_OCM_MSG_ACCEPT 0x05
+#define ANX7688_OCM_MSG_REJECT 0x06
+#define ANX7688_OCM_MSG_PSWAP_REQ 0x10
+#define ANX7688_OCM_MSG_DSWAP_REQ 0x11
+#define ANX7688_OCM_MSG_GOTO_MIN_REQ 0x12
+#define ANX7688_OCM_MSG_VCONN_SWAP_REQ 0x13
+#define ANX7688_OCM_MSG_VDM 0x14
+#define ANX7688_OCM_MSG_DP_SNK_CFG 0x15
+#define ANX7688_OCM_MSG_PWR_OBJ_REQ 0x16
+#define ANX7688_OCM_MSG_PD_STATUS_REQ 0x17
+#define ANX7688_OCM_MSG_DP_ALT_ENTER 0x19
+#define ANX7688_OCM_MSG_DP_ALT_EXIT 0x1a
+#define ANX7688_OCM_MSG_GET_SNK_CAP 0x1b
+#define ANX7688_OCM_MSG_RESPONSE_TO_REQ 0xf0
+#define ANX7688_OCM_MSG_SOFT_RST 0xf1
+#define ANX7688_OCM_MSG_HARD_RST 0xf2
+#define ANX7688_OCM_MSG_RESTART 0xf3
+
+static const char * const anx7688_supply_names[] = {
+ "avdd33",
+ "avdd18",
+ "dvdd18",
+ "avdd10",
+ "dvdd10",
+ "i2c",
+ "hdmi_vt",
+
+ "vconn", // power for VCONN1/VCONN2 switches
+ "vbus", // vbus power
+};
+
+#define ANX7688_NUM_SUPPLIES ARRAY_SIZE(anx7688_supply_names)
+#define ANX7688_NUM_ALWAYS_ON_SUPPLIES (ANX7688_NUM_SUPPLIES - 1)
+
+#define ANX7688_I2C_INDEX (ANX7688_NUM_SUPPLIES - 4)
+#define ANX7688_VCONN_INDEX (ANX7688_NUM_SUPPLIES - 2)
+#define ANX7688_VBUS_INDEX (ANX7688_NUM_SUPPLIES - 1)
+
+enum {
+ ANX7688_F_POWERED,
+ ANX7688_F_CONNECTED,
+ ANX7688_F_FW_FAILED,
+ ANX7688_F_PWRSUPPLY_CHANGE,
+ ANX7688_F_CURRENT_UPDATE,
+};
+
+struct anx7688 {
+ struct device *dev;
+ struct i2c_client *client;
+ struct i2c_client *client_tcpc;
+ struct regulator_bulk_data supplies[ANX7688_NUM_SUPPLIES];
+ struct power_supply *vbus_in_supply;
+ struct notifier_block vbus_in_nb;
+ int input_current_limit; // mA
+ struct gpio_desc *gpio_enable;
+ struct gpio_desc *gpio_reset;
+ struct gpio_desc *gpio_cabledet;
+
+ uint32_t src_caps[8];
+ unsigned n_src_caps;
+
+ uint32_t snk_caps[8];
+ unsigned n_snk_caps;
+
+ unsigned long flags[1];
+
+ struct delayed_work work;
+ struct timer_list work_timer;
+
+ struct mutex lock;
+ bool vbus_on, vconn_on;
+ bool pd_capable;
+ int pd_current_limit; // mA
+ ktime_t current_update_deadline;
+
+ struct typec_port *port;
+ struct typec_partner *partner;
+ struct usb_pd_identity partner_identity;
+ struct usb_role_switch *role_sw;
+ int pwr_role, data_role;
+
+ struct dentry *debug_root;
+
+ /* for debug */
+ int last_status;
+ int last_cc_status;
+ int last_dp_state;
+ int last_bc_result;
+
+ /* for HDMI HPD */
+ struct extcon_dev *extcon;
+ int last_extcon_state;
+};
+
+static const unsigned int anx7688_extcon_cable[] = {
+ EXTCON_DISP_HDMI,
+ EXTCON_NONE,
+};
+
+static int anx7688_reg_read(struct anx7688 *anx7688, u8 reg_addr)
+{
+ int ret;
+
+ ret = i2c_smbus_read_byte_data(anx7688->client, reg_addr);
+ if (ret < 0)
+ dev_err(anx7688->dev, "i2c read failed at 0x%x (%d)\n",
+ reg_addr, ret);
+
+ return ret;
+}
+
+static int anx7688_reg_write(struct anx7688 *anx7688, u8 reg_addr, u8 value)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(anx7688->client, reg_addr, value);
+ if (ret < 0)
+ dev_err(anx7688->dev, "i2c write failed at 0x%x (%d)\n",
+ reg_addr, ret);
+
+ return ret;
+}
+
+static int anx7688_reg_update_bits(struct anx7688 *anx7688, u8 reg_addr,
+ u8 mask, u8 value)
+{
+ int ret;
+
+ ret = anx7688_reg_read(anx7688, reg_addr);
+ if (ret < 0)
+ return ret;
+
+ ret &= ~mask;
+ ret |= value;
+
+ return anx7688_reg_write(anx7688, reg_addr, ret);
+}
+
+static int anx7688_tcpc_reg_read(struct anx7688 *anx7688, u8 reg_addr)
+{
+ int ret;
+
+ ret = i2c_smbus_read_byte_data(anx7688->client_tcpc, reg_addr);
+ if (ret < 0)
+ dev_err(anx7688->dev, "tcpc i2c read failed at 0x%x (%d)\n",
+ reg_addr, ret);
+
+ return ret;
+}
+
+static int anx7688_tcpc_reg_write(struct anx7688 *anx7688, u8 reg_addr, u8 value)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(anx7688->client_tcpc, reg_addr, value);
+ if (ret < 0)
+ dev_err(anx7688->dev, "tcpc i2c write failed at 0x%x (%d)\n",
+ reg_addr, ret);
+
+ return ret;
+}
+
+static void anx7688_power_enable(struct anx7688 *anx7688)
+{
+ gpiod_set_value(anx7688->gpio_reset, 1);
+ gpiod_set_value(anx7688->gpio_enable, 1);
+
+ /* wait for power to stabilize and release reset */
+ msleep(10);
+ gpiod_set_value(anx7688->gpio_reset, 0);
+ udelay(2);
+
+ dev_dbg(anx7688->dev, "power enabled\n");
+
+ set_bit(ANX7688_F_POWERED, anx7688->flags);
+}
+
+static void anx7688_power_disable(struct anx7688 *anx7688)
+{
+ gpiod_set_value(anx7688->gpio_reset, 1);
+ msleep(5);
+ gpiod_set_value(anx7688->gpio_enable, 0);
+
+ dev_dbg(anx7688->dev, "power disabled\n");
+
+ clear_bit(ANX7688_F_POWERED, anx7688->flags);
+}
+
+static int anx7688_send_ocm_message(struct anx7688 *anx7688, int cmd,
+ const u8 *data, int data_len)
+{
+ int ret = 0, i;
+ u8 pkt[32];
+
+ if (data_len > sizeof(pkt) - 3) {
+ dev_dbg(anx7688->dev,
+ "invalid ocm message length cmd=0x%02x len=%d\n",
+ cmd, data_len);
+ return -EINVAL;
+ }
+
+ // prepare pd packet
+ pkt[0] = data_len + 1;
+ pkt[1] = cmd;
+ if (data_len > 0)
+ memcpy(pkt + 2, data, data_len);
+ pkt[2 + data_len] = 0;
+ for (i = 0; i < data_len + 2; i++)
+ pkt[data_len + 2] -= pkt[i];
+
+ dev_dbg(anx7688->dev, "send pd packet cmd=0x%02x %*ph\n",
+ cmd, data_len + 3, pkt);
+
+ ret = anx7688_tcpc_reg_read(anx7688, ANX7688_TCPC_REG_INTERFACE_SEND);
+ if (ret) {
+ dev_err(anx7688->dev,
+ "failed to send pd packet (tx buffer full)\n");
+ return -EBUSY;
+ }
+
+ ret = i2c_smbus_write_i2c_block_data(anx7688->client_tcpc,
+ ANX7688_TCPC_REG_INTERFACE_SEND,
+ data_len + 3, pkt);
+ if (ret < 0)
+ dev_err(anx7688->dev,
+ "failed to send pd packet (err=%d)\n", ret);
+
+ // wait until the message is processed (30ms max)
+ for (i = 0; i < 300; i++) {
+ ret = anx7688_tcpc_reg_read(anx7688, ANX7688_TCPC_REG_INTERFACE_SEND);
+ if (ret <= 0)
+ return ret;
+
+ udelay(100);
+ }
+
+ dev_err(anx7688->dev, "timeout waiting for the message queue flush\n");
+ return -ETIMEDOUT;
+}
+
+static int anx7688_connect(struct anx7688 *anx7688)
+{
+ struct typec_partner_desc desc = {};
+ int ret, i;
+ u8 fw[2];
+ const u8 dp_snk_identity[16] = {
+ 0x00, 0x00, 0x00, 0xec, /* id header */
+ 0x00, 0x00, 0x00, 0x00, /* cert stat */
+ 0x00, 0x00, 0x00, 0x00, /* product type */
+ 0x39, 0x00, 0x00, 0x51 /* alt mode adapter */
+ };
+ const u8 svid[4] = {
+ 0x00, 0x00, 0x01, 0xff,
+ };
+ u32 caps[8];
+
+ dev_dbg(anx7688->dev, "cable inserted\n");
+
+ anx7688->last_status = -1;
+ anx7688->last_cc_status = -1;
+ anx7688->last_dp_state = -1;
+
+ msleep(10);
+ anx7688_power_enable(anx7688);
+
+ ret = regulator_enable(anx7688->supplies[ANX7688_VCONN_INDEX].consumer);
+ if (ret) {
+ dev_err(anx7688->dev, "failed to enable vconn\n");
+ goto err_poweroff;
+ }
+ anx7688->vconn_on = true;
+
+ /* wait till the firmware is loaded (typically ~30ms) */
+ for (i = 0; i < 100; i++) {
+ ret = anx7688_reg_read(anx7688, ANX7688_REG_EEPROM_LOAD_STATUS0);
+
+ if (ret >= 0 && (ret & ANX7688_EEPROM_FW_LOADED) == ANX7688_EEPROM_FW_LOADED) {
+ dev_dbg(anx7688->dev, "eeprom0 = 0x%02x\n", ret);
+ dev_info(anx7688->dev, "fw loaded after %d ms\n", i * 10);
+ goto fw_loaded;
+ }
+
+ msleep(5);
+ }
+
+ set_bit(ANX7688_F_FW_FAILED, anx7688->flags);
+ dev_err(anx7688->dev, "boot firmware load failed (you may need to flash FW to anx7688 first)\n");
+ ret = -ETIMEDOUT;
+ goto err_vconoff;
+
+fw_loaded:
+ ret = i2c_smbus_read_i2c_block_data(anx7688->client,
+ ANX7688_REG_FW_VERSION1, 2, fw);
+ if (ret < 0) {
+ dev_err(anx7688->dev, "failed to read firmware version\n");
+ goto err_vconoff;
+ }
+
+ dev_info(anx7688->dev, "OCM firmware loaded (version 0x%04x)\n",
+ fw[1] | fw[0] << 8);
+
+ /* Unmask interrupts */
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_STATUS_INT, 0);
+ if (ret)
+ goto err_vconoff;
+
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_STATUS_INT_MASK, ~ANX7688_SOFT_INT_MASK);
+ if (ret)
+ goto err_vconoff;
+
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_IRQ_EXT_SOURCE2, 0xff);
+ if (ret)
+ goto err_vconoff;
+
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_IRQ_EXT_MASK2, (u8)~ANX7688_IRQ2_SOFT_INT);
+ if (ret)
+ goto err_vconoff;
+
+ /* time to turn off vbus after cc disconnect (unit is 4 ms) */
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_VBUS_OFF_DELAY_TIME, 100 / 4);
+ if (ret)
+ goto err_vconoff;
+
+ /* 300ms (unit is 2 ms) */
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_TRY_UFP_TIMER, 300 / 2);
+ if (ret)
+ goto err_vconoff;
+
+ /* maximum voltage in 100 mV units */
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_MAX_VOLTAGE, 50); /* 5 V */
+ if (ret)
+ goto err_vconoff;
+
+ /* min/max power in 500 mW units */
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_MAX_POWER, 15 * 2); /* 15 W */
+ if (ret)
+ goto err_vconoff;
+
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_MIN_POWER, 1); /* 0.5 W */
+ if (ret)
+ goto err_vconoff;
+
+ /* auto_pd, try.src, try.sink, goto safe 5V */
+ ret = anx7688_reg_write(anx7688, ANX7688_REG_FEATURE_CTRL, 0x1e & ~BIT(2)); // disable try_src
+ if (ret)
+ goto err_vconoff;
+
+ for (i = 0; i < anx7688->n_src_caps; i++)
+ caps[i] = cpu_to_le32(anx7688->src_caps[i]);
+ ret = anx7688_send_ocm_message(anx7688, ANX7688_OCM_MSG_PWR_SRC_CAP,
+ (u8*)&caps, 4 * anx7688->n_src_caps);
+ if (ret)
+ goto err_vconoff;
+
+ for (i = 0; i < anx7688->n_snk_caps; i++)
+ caps[i] = cpu_to_le32(anx7688->snk_caps[i]);
+ ret = anx7688_send_ocm_message(anx7688, ANX7688_OCM_MSG_PWR_SNK_CAP,
+ (u8*)&caps, 4 * anx7688->n_snk_caps);
+ if (ret)
+ goto err_vconoff;
+
+ /* Send DP SNK identity */
+ ret = anx7688_send_ocm_message(anx7688, ANX7688_OCM_MSG_DP_SNK_IDENTITY,
+ dp_snk_identity, sizeof dp_snk_identity);
+ if (ret)
+ goto err_vconoff;
+
+ ret = anx7688_send_ocm_message(anx7688, ANX7688_OCM_MSG_SVID,
+ svid, sizeof svid);
+ if (ret)
+ goto err_vconoff;
+
+ dev_dbg(anx7688->dev, "OCM configuration completed\n");
+
+ desc.accessory = TYPEC_ACCESSORY_NONE;
+
+ typec_unregister_partner(anx7688->partner);
+
+ anx7688->partner = typec_register_partner(anx7688->port, &desc);
+ if (IS_ERR(anx7688->partner)) {
+ ret = PTR_ERR(anx7688->partner);
+ goto err_vconoff;
+ }
+
+ // after this deadline passes we'll check if device is pd_capable and
+ // set up the current limit accordingly
+ anx7688->current_update_deadline = ktime_add_ms(ktime_get(), 3000);
+
+ set_bit(ANX7688_F_CONNECTED, anx7688->flags);
+ return 0;
+
+err_vconoff:
+ regulator_disable(anx7688->supplies[ANX7688_VCONN_INDEX].consumer);
+ anx7688->vconn_on = false;
+err_poweroff:
+ anx7688_power_disable(anx7688);
+ dev_err(anx7688->dev, "OCM configuration failed\n");
+ return ret;
+}
+
+static void anx7688_set_hdmi_hpd(struct anx7688 *anx7688, int state)
+{
+ if (!anx7688->extcon)
+ return;
+
+ if (anx7688->last_extcon_state != state) {
+ extcon_set_state_sync(anx7688->extcon, EXTCON_DISP_HDMI, state);
+ anx7688->last_extcon_state = state;
+ }
+}
+
+static void anx7688_disconnect(struct anx7688 *anx7688)
+{
+ union power_supply_propval val = {0,};
+ struct device *dev = anx7688->dev;
+ int ret;
+
+ dev_dbg(dev, "cable removed\n");
+
+ anx7688->current_update_deadline = 0;
+
+ anx7688_set_hdmi_hpd(anx7688, 0);
+
+ if (anx7688->vconn_on) {
+ regulator_disable(anx7688->supplies[ANX7688_VCONN_INDEX].consumer);
+ anx7688->vconn_on = false;
+ }
+
+ if (anx7688->vbus_on) {
+ regulator_disable(anx7688->supplies[ANX7688_VBUS_INDEX].consumer);
+ anx7688->vbus_on = false;
+ }
+
+ anx7688_power_disable(anx7688);
+
+ anx7688->pd_capable = false;
+
+ typec_unregister_partner(anx7688->partner);
+ anx7688->partner = NULL;
+
+ anx7688->pwr_role = TYPEC_SINK;
+ anx7688->data_role = TYPEC_DEVICE;
+ typec_set_pwr_role(anx7688->port, anx7688->pwr_role);
+ typec_set_data_role(anx7688->port, anx7688->data_role);
+ typec_set_pwr_opmode(anx7688->port, TYPEC_PWR_MODE_USB);
+ typec_set_vconn_role(anx7688->port, TYPEC_SINK);
+
+ usb_role_switch_set_role(anx7688->role_sw, USB_ROLE_NONE);
+
+ val.intval = 500 * 1000;
+ dev_dbg(dev, "setting vbus_in current limit to %d mA\n", val.intval);
+ ret = power_supply_set_property(anx7688->vbus_in_supply,
+ POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
+ &val);
+ if (ret)
+ dev_err(dev, "failed to set vbus_in current to %d mA\n",
+ val.intval / 1000);
+
+ val.intval = 0;
+ dev_dbg(dev, "disabling vbus_in power path\n");
+ ret = power_supply_set_property(anx7688->vbus_in_supply,
+ POWER_SUPPLY_PROP_ONLINE,
+ &val);
+ if (ret)
+ dev_err(dev, "failed to offline vbus_in\n");
+
+ dev_dbg(dev, "enabling USB BC 1.2 detection\n");
+
+ clear_bit(ANX7688_F_CONNECTED, anx7688->flags);
+}
+
+static void anx7688_handle_cable_change(struct anx7688* anx7688)
+{
+ int cabledet;
+ bool connected;
+
+ connected = test_bit(ANX7688_F_CONNECTED, anx7688->flags);
+ cabledet = gpiod_get_value(anx7688->gpio_cabledet);
+
+ if (cabledet && !connected)
+ anx7688_connect(anx7688);
+ else if (!cabledet && connected)
+ anx7688_disconnect(anx7688);
+}
+
+static irqreturn_t anx7688_irq_plug_handler(int irq, void *data)
+{
+ struct anx7688 *anx7688 = data;
+
+ dev_dbg(anx7688->dev, "plug irq (cd=%d)\n",
+ gpiod_get_value(anx7688->gpio_cabledet));
+
+ /*
+ * After each cabledet change the scheduled work timer is reset
+ * to fire in ~10ms. So the work is done only after the cabledet
+ * is stable for ~10ms.
+ */
+ schedule_delayed_work(&anx7688->work, msecs_to_jiffies(10));
+
+ return IRQ_HANDLED;
+}
+
+enum {
+ CMD_SUCCESS,
+ CMD_REJECT,
+ CMD_FAIL,
+ CMD_BUSY,
+};
+
+static const char* anx7688_cmd_statuses[] = {
+ "SUCCESS",
+ "REJECT",
+ "FAIL",
+ "BUSY",
+};
+
+static int anx7688_handle_pd_message_response(struct anx7688* anx7688,
+ u8 to_cmd, u8 resp)
+{
+ const char* status = resp <= CMD_BUSY ? anx7688_cmd_statuses[resp] : "UNKNOWN";
+
+ switch (to_cmd) {
+ case ANX7688_OCM_MSG_PSWAP_REQ:
+ dev_info(anx7688->dev, "received response to PSWAP_REQ (%s)\n", status);
+ break;
+
+ case ANX7688_OCM_MSG_DSWAP_REQ:
+ dev_info(anx7688->dev, "received response to DSWAP_REQ (%s)\n", status);
+ break;
+
+ case ANX7688_OCM_MSG_VCONN_SWAP_REQ:
+ dev_info(anx7688->dev, "received response to VCONN_SWAP_REQ (%s)\n", status);
+ break;
+
+ case ANX7688_OCM_MSG_PWR_OBJ_REQ:
+ dev_info(anx7688->dev, "received response to PWR_OBJ_REQ (%s)\n", status);
+ break;
+
+ case ANX7688_OCM_MSG_VDM:
+ dev_info(anx7688->dev, "received response to VDM (%s)\n", status);
+ break;
+
+ case ANX7688_OCM_MSG_GOTO_MIN_REQ:
+ dev_info(anx7688->dev, "received response to GOTO_MIN_REQ (%s)\n", status);
+ break;
+
+ case ANX7688_OCM_MSG_GET_SNK_CAP:
+ dev_info(anx7688->dev, "received response to GET_SNK_CAP (%s)\n", status);
+ break;
+
+ default:
+ dev_info(anx7688->dev, "received response to unknown request (%s)\n", status);
+ break;
+ }
+
+ return 0;
+}
+
+static int anx7688_handle_pd_message(struct anx7688* anx7688,
+ u8 cmd, u8* msg, unsigned len)
+{
+ struct device *dev = anx7688->dev;
+ union power_supply_propval psy_val = {0,};
+ uint32_t* pdos = (uint32_t*)msg;
+ int ret, i, rdo_max_v, rdo_max_p;
+ uint32_t pdo, rdo;
+
+ switch (cmd) {
+ case ANX7688_OCM_MSG_PWR_SRC_CAP:
+ dev_info(anx7688->dev, "received SRC_CAP\n");
+
+ if (len % 4 != 0) {
+ dev_warn(anx7688->dev, "received invalid sized PDO array\n");
+ break;
+ }
+
+ /* the partner is PD capable */
+ anx7688->pd_capable = true;
+
+ for (i = 0; i < len / 4; i++) {
+ pdo = le32_to_cpu(pdos[i]);
+
+ if (pdo_type(pdo) == PDO_TYPE_FIXED) {
+ unsigned voltage = pdo_fixed_voltage(pdo);
+ unsigned max_curr = pdo_max_current(pdo);
+
+ dev_info(anx7688->dev, "SRC_CAP PDO_FIXED (%umV %umA)\n", voltage, max_curr);
+ } else if (pdo_type(pdo) == PDO_TYPE_BATT) {
+ unsigned min_volt = pdo_min_voltage(pdo);
+ unsigned max_volt = pdo_max_voltage(pdo);
+ unsigned max_pow = pdo_max_power(pdo);
+
+ dev_info(anx7688->dev, "SRC_CAP PDO_BATT (%umV-%umV %umW)\n", min_volt, max_volt, max_pow);
+ } else if (pdo_type(pdo) == PDO_TYPE_VAR) {
+ unsigned min_volt = pdo_min_voltage(pdo);
+ unsigned max_volt = pdo_max_voltage(pdo);
+ unsigned max_curr = pdo_max_current(pdo);
+
+ dev_info(anx7688->dev, "SRC_CAP PDO_VAR (%umV-%umV %umA)\n", min_volt, max_volt, max_curr);
+ } else {
+ dev_info(anx7688->dev, "SRC_CAP PDO_APDO (0x%08X)\n", pdo);
+ }
+ }
+
+ /* when auto_pd mode is enabled, the FW has already set
+ * RDO_MAX_VOLTAGE and RDO_MAX_POWER for the RDO it sent to the
+ * partner based on the received SOURCE_CAPs. This does not
+ * mean, the request was acked, but we can't do better here than
+ * calculate the current_limit to set later and hope for the best.
+ */
+ rdo_max_v = anx7688_reg_read(anx7688, ANX7688_REG_MAX_VOLTAGE_STATUS);
+ if (rdo_max_v < 0)
+ return rdo_max_v;
+ if (rdo_max_v == 0)
+ return -EINVAL;
+
+ rdo_max_p = anx7688_reg_read(anx7688, ANX7688_REG_MAX_POWER_STATUS);
+ if (rdo_max_p < 0)
+ return rdo_max_p;
+
+ anx7688->pd_current_limit = rdo_max_p * 5000 / rdo_max_v;
+
+ dev_dbg(anx7688->dev, "RDO max voltage = %dmV, max power = %dmW, PD current limit = %dmA\n",
+ rdo_max_v * 100, rdo_max_p * 500, anx7688->pd_current_limit);
+
+ // update current limit sooner, now that we have PD negotiation result
+ anx7688->current_update_deadline = ktime_add_ms(ktime_get(), 500);
+ break;
+
+ case ANX7688_OCM_MSG_PWR_SNK_CAP:
+ dev_info(anx7688->dev, "received SNK_CAP\n");
+
+ if (len % 4 != 0) {
+ dev_warn(anx7688->dev, "received invalid sized PDO array\n");
+ break;
+ }
+
+ for (i = 0; i < len / 4; i++) {
+ pdo = le32_to_cpu(pdos[i]);
+
+ if (pdo_type(pdo) == PDO_TYPE_FIXED) {
+ unsigned voltage = pdo_fixed_voltage(pdo);
+ unsigned max_curr = pdo_max_current(pdo);
+
+ dev_info(anx7688->dev, "SNK_CAP PDO_FIXED (%umV %umA)\n", voltage, max_curr);
+ } else if (pdo_type(pdo) == PDO_TYPE_BATT) {
+ unsigned min_volt = pdo_min_voltage(pdo);
+ unsigned max_volt = pdo_max_voltage(pdo);
+ unsigned max_pow = pdo_max_power(pdo);
+
+ dev_info(anx7688->dev, "SNK_CAP PDO_BATT (%umV-%umV %umW)\n", min_volt, max_volt, max_pow);
+ } else if (pdo_type(pdo) == PDO_TYPE_VAR) {
+ unsigned min_volt = pdo_min_voltage(pdo);
+ unsigned max_volt = pdo_max_voltage(pdo);
+ unsigned max_curr = pdo_max_current(pdo);
+
+ dev_info(anx7688->dev, "SNK_CAP PDO_VAR (%umV-%umV %umA)\n", min_volt, max_volt, max_curr);
+ } else {
+ dev_info(anx7688->dev, "SNK_CAP PDO_APDO (0x%08X)\n", pdo);
+ }
+ }
+
+ break;
+
+ case ANX7688_OCM_MSG_PWR_OBJ_REQ:
+ dev_info(anx7688->dev, "received PWR_OBJ_REQ\n");
+
+ anx7688->pd_capable = true;
+
+ if (len != 4) {
+ dev_warn(anx7688->dev, "received invalid sized RDO\n");
+ break;
+ }
+
+ rdo = le32_to_cpu(pdos[0]);
+
+ if (rdo_index(rdo) >= 1 && rdo_index(rdo) <= anx7688->n_src_caps) {
+ unsigned rdo_op_curr = rdo_op_current(rdo);
+ unsigned rdo_max_curr = rdo_max_current(rdo);
+ unsigned rdo_idx = rdo_index(rdo) - 1;
+ unsigned pdo_volt, pdo_max_curr;
+
+ pdo = anx7688->src_caps[rdo_idx];
+ pdo_volt = pdo_fixed_voltage(pdo);
+ pdo_max_curr = pdo_max_current(pdo);
+
+ dev_info(anx7688->dev, "RDO (idx=%d op=%umA max=%umA)\n",
+ rdo_idx, rdo_op_curr, rdo_max_curr);
+
+ dev_info(anx7688->dev, "PDO_FIXED (%umV %umA)\n",
+ pdo_volt, pdo_max_curr);
+
+ // We could check the req and respond with accept/reject
+ // but we're using auto_pd feature, so the FW will do
+ // this for us
+ } else {
+ dev_info(anx7688->dev, "PWR_OBJ RDO index out of range (RDO = 0x%08X)\n", rdo);
+ }
+
+ break;
+
+ case ANX7688_OCM_MSG_ACCEPT:
+ dev_info(anx7688->dev, "received ACCEPT\n");
+ break;
+
+ case ANX7688_OCM_MSG_REJECT:
+ dev_info(anx7688->dev, "received REJECT\n");
+ break;
+
+ case ANX7688_OCM_MSG_RESPONSE_TO_REQ:
+ if (len < 2) {
+ dev_warn(anx7688->dev, "received short RESPONSE_TO_REQ\n");
+ break;
+ }
+
+ anx7688_handle_pd_message_response(anx7688, msg[0], msg[1]);
+ break;
+
+ case ANX7688_OCM_MSG_SOFT_RST:
+ dev_info(anx7688->dev, "received SOFT_RST\n");
+ break;
+
+ case ANX7688_OCM_MSG_HARD_RST:
+ if (anx7688->pd_capable) {
+ dev_info(anx7688->dev, "received HARD_RST\n");
+
+ // stop drawing power from VBUS
+ psy_val.intval = 0;
+ dev_dbg(dev, "disabling vbus_in power path\n");
+ ret = power_supply_set_property(anx7688->vbus_in_supply,
+ POWER_SUPPLY_PROP_ONLINE,
+ &psy_val);
+ if (ret)
+ dev_err(anx7688->dev, "failed to offline vbus_in\n");
+
+ // wait till the dust settles
+ anx7688->current_update_deadline = ktime_add_ms(ktime_get(), 3000);
+ } else {
+ dev_dbg(anx7688->dev, "received HARD_RST, idiot firmware is bored\n");
+ }
+
+ break;
+
+ case ANX7688_OCM_MSG_RESTART:
+ dev_info(anx7688->dev, "received RESTART\n");
+ break;
+
+ case ANX7688_OCM_MSG_PSWAP_REQ:
+ dev_info(anx7688->dev, "received PSWAP_REQ\n");
+ break;
+
+ case ANX7688_OCM_MSG_DSWAP_REQ:
+ dev_info(anx7688->dev, "received DSWAP_REQ\n");
+ break;
+
+ case ANX7688_OCM_MSG_VCONN_SWAP_REQ:
+ dev_info(anx7688->dev, "received VCONN_SWAP_REQ\n");
+ break;
+
+ case ANX7688_OCM_MSG_DP_ALT_ENTER:
+ dev_info(anx7688->dev, "received DP_ALT_ENTER\n");
+ break;
+
+ case ANX7688_OCM_MSG_DP_ALT_EXIT:
+ dev_info(anx7688->dev, "received DP_ALT_EXIT\n");
+ break;
+
+ case ANX7688_OCM_MSG_DP_SNK_IDENTITY:
+ dev_info(anx7688->dev, "received DP_SNK_IDENTITY\n");
+ break;
+
+ case ANX7688_OCM_MSG_SVID:
+ dev_info(anx7688->dev, "received SVID\n");
+ break;
+
+ case ANX7688_OCM_MSG_VDM:
+ dev_info(anx7688->dev, "received VDM\n");
+ break;
+
+ case ANX7688_OCM_MSG_GOTO_MIN_REQ:
+ dev_info(anx7688->dev, "received GOTO_MIN_REQ\n");
+ break;
+
+ case ANX7688_OCM_MSG_PD_STATUS_REQ:
+ dev_info(anx7688->dev, "received PD_STATUS_REQ\n");
+ break;
+
+ case ANX7688_OCM_MSG_GET_DP_SNK_CAP:
+ dev_info(anx7688->dev, "received GET_DP_SNK_CAP\n");
+ break;
+
+ case ANX7688_OCM_MSG_DP_SNK_CFG:
+ dev_info(anx7688->dev, "received DP_SNK_CFG\n");
+ break;
+
+ default:
+ dev_info(anx7688->dev, "received unknown message 0x%02x\n", cmd);
+ break;
+ }
+
+ return 0;
+}
+
+static int anx7688_receive_msg(struct anx7688* anx7688)
+{
+ u8 pkt[32], checksum = 0;
+ int i, ret;
+
+ ret = i2c_smbus_read_i2c_block_data(anx7688->client_tcpc,
+ ANX7688_TCPC_REG_INTERFACE_RECV,
+ 32, pkt);
+ if (ret < 0) {
+ dev_err(anx7688->dev, "failed to read pd msg\n");
+ return ret;
+ }
+
+ ret = anx7688_tcpc_reg_write(anx7688, ANX7688_TCPC_REG_INTERFACE_RECV, 0);
+ if (ret) {
+ dev_warn(anx7688->dev, "failed to clear recv fifo\n");
+ }
+
+ if (pkt[0] == 0 || pkt[0] > sizeof(pkt) - 2) {
+ dev_err(anx7688->dev, "received invalid pd message: %*ph\n",
+ (int)sizeof(pkt), pkt);
+ return -EINVAL;
+ }
+
+ dev_dbg(anx7688->dev, "recv ocm message cmd=0x%02x %*ph\n",
+ pkt[1], pkt[0] + 2, pkt);
+
+ for (i = 0; i < pkt[0] + 2; i++)
+ checksum += pkt[i];
+
+ if (checksum != 0) {
+ dev_err(anx7688->dev, "bad checksum on received message\n");
+ return -EINVAL;
+ }
+
+ anx7688_handle_pd_message(anx7688, pkt[1], pkt + 2, pkt[0] - 1);
+ return 0;
+}
+
+static const char* anx7688_cc_status_string(unsigned v)
+{
+ switch (v) {
+ case 0: return "SRC.Open";
+ case 1: return "SRC.Rd";
+ case 2: return "SRC.Ra";
+ case 4: return "SNK.Default";
+ case 8: return "SNK.Power1.5";
+ case 12: return "SNK.Power3.0";
+ default: return "UNK";
+ }
+}
+
+static int anx7688_update_status(struct anx7688 *anx7688)
+{
+ struct device *dev = anx7688->dev;
+ bool vbus_on, vconn_on, dr_dfp;
+ int status, cc_status, dp_state, dp_substate, ret;
+
+ status = anx7688_reg_read(anx7688, ANX7688_REG_STATUS);
+ if (status < 0)
+ return status;
+
+ cc_status = anx7688_reg_read(anx7688, ANX7688_REG_CC_STATUS);
+ if (cc_status < 0)
+ return cc_status;
+
+ dp_state = anx7688_tcpc_reg_read(anx7688, 0x87);
+ if (dp_state < 0)
+ return dp_state;
+
+ dp_substate = anx7688_tcpc_reg_read(anx7688, 0x88);
+ if (dp_substate < 0)
+ return dp_substate;
+
+ anx7688_set_hdmi_hpd(anx7688, dp_state >= 3);
+
+ dp_state = (dp_state << 8) | dp_substate;
+
+ if (anx7688->last_status == -1 || anx7688->last_status != status) {
+ anx7688->last_status = status;
+ dev_dbg(dev, "status changed to 0x%02x\n", status);
+ }
+
+ if (anx7688->last_cc_status == -1 || anx7688->last_cc_status != cc_status) {
+ anx7688->last_cc_status = cc_status;
+ dev_dbg(dev, "cc_status changed to CC1 = %s CC2 = %s\n",
+ anx7688_cc_status_string(cc_status & 0xf),
+ anx7688_cc_status_string((cc_status >> 4) & 0xf));
+ }
+
+ if (anx7688->last_dp_state == -1 || anx7688->last_dp_state != dp_state) {
+ anx7688->last_dp_state = dp_state;
+ dev_dbg(dev, "DP state changed to 0x%04x\n", dp_state);
+ }
+
+ vbus_on = !!(status & ANX7688_VBUS_STATUS);
+ vconn_on = !!(status & ANX7688_VCONN_STATUS);
+ dr_dfp = !!(status & ANX7688_DATA_ROLE_STATUS);
+
+ if (anx7688->vbus_on != vbus_on) {
+ dev_dbg(anx7688->dev, "POWER role change to %s\n",
+ vbus_on ? "SOURCE" : "SINK");
+
+ if (vbus_on) {
+ ret = regulator_enable(anx7688->supplies[ANX7688_VBUS_INDEX].consumer);
+ if (ret) {
+ dev_err(anx7688->dev, "failed to enable vbus\n");
+ return ret;
+ }
+ } else {
+ ret = regulator_disable(anx7688->supplies[ANX7688_VBUS_INDEX].consumer);
+ if (ret) {
+ dev_err(anx7688->dev, "failed to disable vbus\n");
+ return ret;
+ }
+ }
+
+ anx7688->pwr_role = vbus_on ? TYPEC_SOURCE : TYPEC_SINK;
+ typec_set_pwr_role(anx7688->port, anx7688->pwr_role);
+ anx7688->vbus_on = vbus_on;
+ }
+
+ if (anx7688->vconn_on != vconn_on) {
+ dev_dbg(anx7688->dev, "VCONN role change to %s\n",
+ vconn_on ? "SOURCE" : "SINK");
+
+ if (vconn_on) {
+ ret = regulator_enable(anx7688->supplies[ANX7688_VCONN_INDEX].consumer);
+ if (ret) {
+ dev_err(anx7688->dev, "failed to enable vconn\n");
+ return ret;
+ }
+ } else {
+ ret = regulator_disable(anx7688->supplies[ANX7688_VCONN_INDEX].consumer);
+ if (ret) {
+ dev_err(anx7688->dev, "failed to disable vconn\n");
+ return ret;
+ }
+ }
+
+ typec_set_vconn_role(anx7688->port, vconn_on ? TYPEC_SOURCE : TYPEC_SINK);
+ anx7688->vconn_on = vconn_on;
+ }
+
+ anx7688->data_role = dr_dfp ? TYPEC_HOST : TYPEC_DEVICE;
+ typec_set_data_role(anx7688->port, anx7688->data_role);
+
+ if (usb_role_switch_get_role(anx7688->role_sw) !=
+ (dr_dfp ? USB_ROLE_HOST : USB_ROLE_DEVICE)) {
+ dev_dbg(anx7688->dev, "DATA role change requested to %s\n",
+ dr_dfp ? "DFP" : "UFP");
+
+ ret = usb_role_switch_set_role(anx7688->role_sw,
+ dr_dfp ? USB_ROLE_HOST : USB_ROLE_DEVICE);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static irqreturn_t anx7688_irq_status_handler(int irq, void *data)
+{
+ struct anx7688 *anx7688 = data;
+ struct device *dev = anx7688->dev;
+ int tcpc_status, ext2_status, soft_status;
+
+ mutex_lock(&anx7688->lock);
+
+ if (!test_bit(ANX7688_F_CONNECTED, anx7688->flags)) {
+ dev_dbg(dev, "spurious status irq\n");
+ /* anx chip should be disabled and power off, nothing
+ * more to do */
+ goto out_unlock;
+ }
+
+ // clear tcpc interrupt
+ tcpc_status = anx7688_tcpc_reg_read(anx7688, ANX7688_TCPC_REG_ALERT0);
+ if (tcpc_status > 0) {
+ anx7688_tcpc_reg_write(anx7688, ANX7688_TCPC_REG_ALERT0, tcpc_status);
+ }
+
+ ext2_status = anx7688_reg_read(anx7688, ANX7688_REG_IRQ_EXT_SOURCE2);
+ if (ext2_status & ANX7688_IRQ2_SOFT_INT) {
+ soft_status = anx7688_reg_read(anx7688, ANX7688_REG_STATUS_INT);
+ anx7688_reg_write(anx7688, ANX7688_REG_STATUS_INT, 0);
+
+ if (soft_status > 0) {
+ soft_status &= ANX7688_SOFT_INT_MASK;
+
+ if (soft_status & ANX7688_IRQS_RECEIVED_MSG)
+ anx7688_receive_msg(anx7688);
+
+ if (soft_status & (ANX7688_IRQS_CC_STATUS_CHANGE |
+ ANX7688_IRQS_VBUS_CHANGE |
+ ANX7688_IRQS_VCONN_CHANGE |
+ ANX7688_IRQS_DATA_ROLE_CHANGE)) {
+ anx7688_update_status(anx7688);
+ }
+ }
+
+ anx7688_reg_write(anx7688, ANX7688_REG_IRQ_EXT_SOURCE2, ANX7688_IRQ2_SOFT_INT);
+ }
+
+out_unlock:
+ mutex_unlock(&anx7688->lock);
+
+ return IRQ_HANDLED;
+}
+
+static int anx7688_dr_set(struct typec_port *port, enum typec_data_role role)
+{
+ struct anx7688 *anx7688 = typec_get_drvdata(port);
+ int ret = 0;
+
+ dev_info(anx7688->dev, "data role set %d\n", role);
+
+ if (anx7688->data_role != role) {
+ mutex_lock(&anx7688->lock);
+ ret = anx7688_send_ocm_message(anx7688, ANX7688_OCM_MSG_DSWAP_REQ, 0, 0);
+ mutex_unlock(&anx7688->lock);
+ }
+
+ return ret;
+}
+
+static int anx7688_pr_set(struct typec_port *port, enum typec_role role)
+{
+ struct anx7688 *anx7688 = typec_get_drvdata(port);
+ int ret = 0;
+
+ dev_info(anx7688->dev, "power role set %d\n", role);
+
+ if (anx7688->pwr_role != role) {
+ mutex_lock(&anx7688->lock);
+ ret = anx7688_send_ocm_message(anx7688, ANX7688_OCM_MSG_PSWAP_REQ, 0, 0);
+ mutex_unlock(&anx7688->lock);
+ }
+
+ return ret;
+}
+
+/*
+ * Calls to the EEPROM functions need to be taken under the anx7688 lock.
+ */
+static int anx7688_eeprom_set_address(struct anx7688 *anx7688, u16 addr)
+{
+ int ret;
+
+ ret = anx7688_reg_write(anx7688, 0xe0, (addr >> 8) & 0xff);
+ if (ret < 0)
+ return ret;
+
+ return anx7688_reg_write(anx7688, 0xe1, addr & 0xff);
+}
+
+static int anx7688_eeprom_wait_done(struct anx7688 *anx7688)
+{
+ ktime_t timeout;
+ int ret;
+
+ // wait for read to be done
+ timeout = ktime_add_us(ktime_get(), 50000);
+ while (true) {
+ ret = anx7688_reg_read(anx7688, 0xe2);
+ if (ret < 0)
+ return ret;
+
+ if (ret & BIT(3))
+ return 0;
+
+ if (ktime_after(ktime_get(), timeout)) {
+ dev_err(anx7688->dev, "timeout waiting for eeprom\n");
+ return -ETIMEDOUT;
+ }
+ }
+}
+
+/* wait for internal FSM of EEPROM to be in a state ready for
+ * programming/reading
+ */
+static int anx7688_eeprom_wait_ready(struct anx7688 *anx7688)
+{
+ ktime_t timeout;
+ int ret;
+
+ // wait until eeprom is ready
+ timeout = ktime_add_us(ktime_get(), 1000000);
+ while (true) {
+ ret = anx7688_reg_read(anx7688, 0x7f);
+ if (ret < 0)
+ return ret;
+
+ if ((ret & 0x0f) == 7)
+ return 0;
+
+ if (ktime_after(ktime_get(), timeout)) {
+ dev_err(anx7688->dev, "timeout waiting for eeprom to initialize\n");
+ return -ETIMEDOUT;
+ }
+
+ msleep(5);
+ }
+}
+
+static int anx7688_eeprom_read(struct anx7688 *anx7688, unsigned addr, u8 buf[16])
+{
+ int ret;
+
+ ret = anx7688_eeprom_set_address(anx7688, addr);
+ if (ret)
+ return ret;
+
+ // initiate read
+ ret = anx7688_reg_write(anx7688, 0xe2, 0x06);
+ if (ret < 0)
+ return ret;
+
+ ret = anx7688_eeprom_wait_done(anx7688);
+ if (ret)
+ return ret;
+
+ ret = i2c_smbus_read_i2c_block_data(anx7688->client, 0xd0, 16, buf);
+ if (ret < 0) {
+ dev_err(anx7688->dev,
+ "failed to read eeprom data (err=%d)\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct typec_operations anx7688_typec_ops = {
+ .dr_set = anx7688_dr_set,
+ .pr_set = anx7688_pr_set,
+};
+
+/*
+ * This function has to work when the ANX7688 is active, and when
+ * it is powered down. It power cycles the chip and asserts the OCM
+ * reset, to prevent OCM FW interfering with EEPROM reading.
+ *
+ * After reading EEPROM, the reconnection is scheduled.
+ */
+static int anx7688_firmware_show(struct seq_file *s, void *data)
+{
+ struct anx7688 *anx7688 = s->private;
+ unsigned addr;
+ u8 buf[16];
+ int ret;
+
+ mutex_lock(&anx7688->lock);
+
+ if (test_bit(ANX7688_F_CONNECTED, anx7688->flags))
+ anx7688_disconnect(anx7688);
+
+ msleep(20);
+
+ anx7688_power_enable(anx7688);
+
+ ret = anx7688_reg_update_bits(anx7688, ANX7688_REG_USBC_RESET_CTRL,
+ ANX7688_USBC_RESET_CTRL_OCM_RESET,
+ ANX7688_USBC_RESET_CTRL_OCM_RESET);
+ if (ret < 0)
+ goto out_powerdown;
+
+ ret = anx7688_eeprom_wait_ready(anx7688);
+ if (ret)
+ goto out_powerdown;
+
+ msleep(10);
+
+ for (addr = 0x10; addr < 0x10000; addr += 16) {
+ // set address
+ ret = anx7688_eeprom_read(anx7688, addr, buf);
+ if (ret < 0)
+ goto out_powerdown;
+
+ seq_write(s, buf, sizeof buf);
+ }
+
+out_powerdown:
+ anx7688_power_disable(anx7688);
+ schedule_delayed_work(&anx7688->work, 0);
+ mutex_unlock(&anx7688->lock);
+
+ return ret;
+}
+DEFINE_SHOW_ATTRIBUTE(anx7688_firmware);
+
+static int anx7688_regs_show(struct seq_file *s, void *data)
+{
+ struct anx7688 *anx7688 = s->private;
+ u8 buf[16];
+ unsigned i, addr;
+ int ret = -ENODEV;
+
+ mutex_lock(&anx7688->lock);
+
+ if (!test_bit(ANX7688_F_POWERED, anx7688->flags))
+ goto out_unlock;
+
+ for (addr = 0; addr < 256; addr += 16) {
+ ret = i2c_smbus_read_i2c_block_data(anx7688->client, addr,
+ sizeof buf, buf);
+ if (ret < 0) {
+ dev_err(anx7688->dev,
+ "failed to read registers (err=%d)\n", ret);
+ goto out_unlock;
+ }
+
+ for (i = 0; i < 16; i++)
+ seq_printf(s, "50%02x: %02x\n", addr + i, buf[i]);
+ }
+
+ for (addr = 0; addr < 256; addr += 16) {
+ ret = i2c_smbus_read_i2c_block_data(anx7688->client_tcpc, addr,
+ sizeof buf, buf);
+ if (ret < 0) {
+ dev_err(anx7688->dev,
+ "failed to read registers (err=%d)\n", ret);
+ goto out_unlock;
+ }
+
+ for (i = 0; i < 16; i++)
+ seq_printf(s, "58%02x: %02x\n", addr + i, buf[i]);
+ }
+
+out_unlock:
+ mutex_unlock(&anx7688->lock);
+
+ return ret;
+}
+DEFINE_SHOW_ATTRIBUTE(anx7688_regs);
+
+static int anx7688_status_show(struct seq_file *s, void *data)
+{
+ struct anx7688 *anx7688 = s->private;
+
+ mutex_lock(&anx7688->lock);
+
+ seq_printf(s, "not much\n");
+
+ mutex_unlock(&anx7688->lock);
+
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(anx7688_status);
+
+/*
+ * This is just a 1s watchdog checking the state if cabledet pin.
+ */
+static void anx7688_cabledet_timer_fn(struct timer_list *t)
+{
+ struct anx7688 *anx7688 = from_timer(anx7688, t, work_timer);
+
+ schedule_delayed_work(&anx7688->work, 0);
+ mod_timer(t, jiffies + msecs_to_jiffies(1000));
+}
+
+static void anx7688_handle_vbus_in_notify(struct anx7688 *anx7688)
+{
+ union power_supply_propval psy_val = {0,};
+ struct device *dev = anx7688->dev;
+ int ret;
+
+ ret = power_supply_get_property(anx7688->vbus_in_supply,
+ POWER_SUPPLY_PROP_USB_TYPE,
+ &psy_val);
+ if (ret) {
+ dev_err(dev, "failed to get USB BC1.2 result\n");
+ return;
+ }
+
+ if (anx7688->last_bc_result == psy_val.intval)
+ return;
+
+ anx7688->last_bc_result = psy_val.intval;
+
+ switch (psy_val.intval) {
+ case POWER_SUPPLY_USB_TYPE_DCP:
+ case POWER_SUPPLY_USB_TYPE_CDP:
+ dev_dbg(dev, "BC 1.2 result: DCP or CDP\n");
+ break;
+ case POWER_SUPPLY_USB_TYPE_SDP:
+ default:
+ dev_dbg(dev, "BC 1.2 result: SDP\n");
+ break;
+ }
+}
+
+static int anx7688_cc_status(unsigned v)
+{
+ switch (v) {
+ case 0: return -1;
+ case 1: return -1;
+ case 2: return -1;
+ case 4: return TYPEC_PWR_MODE_USB;
+ case 8: return TYPEC_PWR_MODE_1_5A;
+ case 12: return TYPEC_PWR_MODE_3_0A;
+ default: return -1;
+ }
+}
+
+static const char *anx7688_get_power_mode_name(enum typec_pwr_opmode mode)
+{
+ switch (mode) {
+ case TYPEC_PWR_MODE_USB: return "USB";
+ case TYPEC_PWR_MODE_1_5A: return "1.5A";
+ case TYPEC_PWR_MODE_3_0A: return "3.0A";
+ case TYPEC_PWR_MODE_PD: return "PD";
+ default: return "Unknown";
+ }
+}
+
+/*
+ * This is called after 500ms after connection when the PD contract should have
+ * been negotiated. We should inspect CC pins or PD status here and decide what
+ * input current limit to set.
+ */
+static void anx7688_handle_current_update(struct anx7688* anx7688)
+{
+ unsigned cc_status = anx7688->last_cc_status;
+ union power_supply_propval val = {0,};
+ struct device *dev = anx7688->dev;
+ int pwr_mode, ret, current_limit = 0;
+
+ if (anx7688->pd_capable) {
+ pwr_mode = TYPEC_PWR_MODE_PD;
+ } else if (cc_status < 0) {
+ pwr_mode = TYPEC_PWR_MODE_USB;
+ } else {
+ pwr_mode = anx7688_cc_status(cc_status & 0xf);
+ if (pwr_mode < 0)
+ pwr_mode = anx7688_cc_status((cc_status >> 4) & 0xf);
+ if (pwr_mode < 0)
+ pwr_mode = TYPEC_PWR_MODE_USB;
+ }
+
+ if (pwr_mode == TYPEC_PWR_MODE_1_5A)
+ current_limit = 1500;
+ else if (pwr_mode == TYPEC_PWR_MODE_3_0A)
+ current_limit = 3000;
+ else if (pwr_mode == TYPEC_PWR_MODE_PD)
+ current_limit = anx7688->pd_current_limit;
+
+ anx7688->input_current_limit = current_limit;
+
+ dev_info(anx7688->dev, "updating power mode to %s, current limit %dmA (0 => BC1.2)\n",
+ anx7688_get_power_mode_name(pwr_mode), current_limit);
+
+ if (current_limit) {
+ /*
+ * Disable BC1.2 detection, because we'll be setting
+ * a current limit determined by USB-PD
+ */
+ dev_dbg(dev, "disabling USB BC 1.2 detection\n");
+
+ val.intval = current_limit * 1000;
+ dev_dbg(dev, "setting vbus_in current limit to %d mA\n", current_limit);
+ ret = power_supply_set_property(anx7688->vbus_in_supply,
+ POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
+ &val);
+ if (ret)
+ dev_err(dev, "failed to set vbus_in current to %d mA\n",
+ current_limit);
+ }
+ /*
+ * else use the result of BC1.2 detection performed by PMIC.
+ */
+
+ /* Turn on VBUS power path inside PMIC. */
+ val.intval = 1;
+ dev_dbg(dev, "enabling vbus_in power path\n");
+ ret = power_supply_set_property(anx7688->vbus_in_supply,
+ POWER_SUPPLY_PROP_ONLINE,
+ &val);
+ if (ret)
+ dev_err(anx7688->dev, "failed to enable vbus_in\n");
+
+ typec_set_pwr_opmode(anx7688->port, pwr_mode);
+}
+
+static int anx7688_vbus_in_notify(struct notifier_block *nb,
+ unsigned long val, void *v)
+{
+ struct anx7688 *anx7688 = container_of(nb, struct anx7688, vbus_in_nb);
+ struct power_supply *psy = v;
+
+ /* atomic context */
+ if (val == PSY_EVENT_PROP_CHANGED && psy == anx7688->vbus_in_supply) {
+ set_bit(ANX7688_F_PWRSUPPLY_CHANGE, anx7688->flags);
+ schedule_delayed_work(&anx7688->work, 0);
+ }
+
+ return NOTIFY_OK;
+}
+
+static void anx7688_work(struct work_struct *work)
+{
+ struct anx7688 *anx7688 = container_of(work, struct anx7688, work.work);
+
+ if (test_bit(ANX7688_F_FW_FAILED, anx7688->flags))
+ return;
+
+ mutex_lock(&anx7688->lock);
+
+ if (test_and_clear_bit(ANX7688_F_PWRSUPPLY_CHANGE, anx7688->flags))
+ anx7688_handle_vbus_in_notify(anx7688);
+
+ anx7688_handle_cable_change(anx7688);
+
+ if (test_bit(ANX7688_F_CONNECTED, anx7688->flags)) {
+ /*
+ * We check status periodically outside of interrupt, just to
+ * be sure we didn't miss any status interrupts
+ */
+ anx7688_update_status(anx7688);
+
+ if (anx7688->current_update_deadline &&
+ ktime_after(ktime_get(), anx7688->current_update_deadline)) {
+ anx7688->current_update_deadline = 0;
+ anx7688_handle_current_update(anx7688);
+ }
+ }
+
+ mutex_unlock(&anx7688->lock);
+}
+
+static int anx7688_i2c_probe(struct i2c_client *client)
+{
+ struct anx7688 *anx7688;
+ struct device *dev = &client->dev;
+ struct typec_capability typec_cap = { };
+ int i, vid_h, vid_l;
+ int irq_cabledet;
+ int ret = 0;
+
+ anx7688 = devm_kzalloc(dev, sizeof(*anx7688), GFP_KERNEL);
+ if (!anx7688)
+ return -ENOMEM;
+
+ i2c_set_clientdata(client, anx7688);
+ anx7688->client = client;
+ anx7688->dev = &client->dev;
+ mutex_init(&anx7688->lock);
+ INIT_DELAYED_WORK(&anx7688->work, anx7688_work);
+ anx7688->last_extcon_state = -1;
+
+ ret = of_property_read_variable_u32_array(dev->of_node, "source-caps",
+ anx7688->src_caps,
+ 1, ARRAY_SIZE(anx7688->src_caps));
+ if (ret < 0) {
+ dev_err(dev, "failed to get source-caps from DT\n");
+ return ret;
+ }
+ anx7688->n_src_caps = ret;
+
+ ret = of_property_read_variable_u32_array(dev->of_node, "sink-caps",
+ anx7688->snk_caps,
+ 1, ARRAY_SIZE(anx7688->snk_caps));
+ if (ret < 0) {
+ dev_err(dev, "failed to get sink-caps from DT\n");
+ return ret;
+ }
+ anx7688->n_snk_caps = ret;
+
+ for (i = 0; i < ANX7688_NUM_SUPPLIES; i++)
+ anx7688->supplies[i].supply = anx7688_supply_names[i];
+ ret = devm_regulator_bulk_get(dev, ANX7688_NUM_SUPPLIES,
+ anx7688->supplies);
+ if (ret)
+ return ret;
+
+ anx7688->vbus_in_supply =
+ devm_power_supply_get_by_phandle(dev, "vbus_in-supply");
+ if (IS_ERR(anx7688->vbus_in_supply)) {
+ dev_err(dev, "Couldn't get the VBUS power supply\n");
+ return PTR_ERR(anx7688->vbus_in_supply);
+ }
+
+ if (!anx7688->vbus_in_supply)
+ return -EPROBE_DEFER;
+
+ anx7688->gpio_enable = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
+ if (IS_ERR(anx7688->gpio_enable)) {
+ dev_err(dev, "Could not get enable gpio\n");
+ return PTR_ERR(anx7688->gpio_enable);
+ }
+
+ anx7688->gpio_reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(anx7688->gpio_reset)) {
+ dev_err(dev, "Could not get reset gpio\n");
+ return PTR_ERR(anx7688->gpio_reset);
+ }
+
+ anx7688->gpio_cabledet = devm_gpiod_get(dev, "cabledet", GPIOD_IN);
+ if (IS_ERR(anx7688->gpio_cabledet)) {
+ dev_err(dev, "Could not get cabledet gpio\n");
+ return PTR_ERR(anx7688->gpio_cabledet);
+ }
+
+ irq_cabledet = gpiod_to_irq(anx7688->gpio_cabledet);
+ if (irq_cabledet < 0) {
+ dev_err(dev, "Could not get cabledet irq\n");
+ return irq_cabledet;
+ }
+
+ // Initialize extcon device
+ anx7688->extcon = devm_extcon_dev_allocate(dev, anx7688_extcon_cable);
+ if (IS_ERR(anx7688->extcon))
+ return -ENOMEM;
+
+ ret = devm_extcon_dev_register(dev, anx7688->extcon);
+ if (ret) {
+ dev_err(dev, "failed to register extcon device\n");
+ return ret;
+ }
+
+ // Register the TCPC i2c interface as second interface (0x58)
+ anx7688->client_tcpc = i2c_new_dummy_device(client->adapter, 0x2c);
+ if (IS_ERR(anx7688->client_tcpc)) {
+ dev_err(dev, "Could not register tcpc i2c client\n");
+ return PTR_ERR(anx7688->client_tcpc);
+ }
+ i2c_set_clientdata(anx7688->client_tcpc, anx7688);
+
+ // powerup and probe the ANX chip
+
+ ret = regulator_bulk_enable(ANX7688_NUM_ALWAYS_ON_SUPPLIES,
+ anx7688->supplies);
+ if (ret) {
+ dev_err(dev, "Could not enable regulators\n");
+ goto err_dummy_dev;
+ }
+
+ msleep(10);
+
+ anx7688_power_enable(anx7688);
+
+ vid_l = anx7688_tcpc_reg_read(anx7688, ANX7688_TCPC_REG_VENDOR_ID0);
+ vid_h = anx7688_tcpc_reg_read(anx7688, ANX7688_TCPC_REG_VENDOR_ID1);
+ if (vid_l < 0 || vid_h < 0) {
+ ret = vid_l < 0 ? vid_l : vid_h;
+ anx7688_power_disable(anx7688);
+ goto err_disable_reg;
+ }
+
+ dev_info(dev, "Vendor id 0x%04x\n", vid_l | vid_h << 8);
+
+ anx7688_power_disable(anx7688);
+
+ anx7688->role_sw = usb_role_switch_get(dev);
+ if (IS_ERR(anx7688->role_sw)) {
+ dev_err(dev, "Could not get role switch\n");
+ ret = PTR_ERR(anx7688->role_sw);
+ goto err_disable_reg;
+ }
+
+ // setup a typec port device
+ typec_cap.revision = USB_TYPEC_REV_1_2;
+ typec_cap.pd_revision = 0x200;
+ typec_cap.prefer_role = TYPEC_NO_PREFERRED_ROLE;
+ typec_cap.type = TYPEC_PORT_DRP;
+ typec_cap.data = TYPEC_PORT_DRD;
+ typec_cap.driver_data = anx7688;
+ typec_cap.ops = &anx7688_typec_ops;
+
+ anx7688->port = typec_register_port(dev, &typec_cap);
+ if (IS_ERR(anx7688->port)) {
+ dev_err(dev, "Could not register type-c port\n");
+ ret = PTR_ERR(anx7688->port);
+ goto err_role_sw;
+ }
+
+ anx7688->pwr_role = TYPEC_SINK;
+ anx7688->data_role = TYPEC_DEVICE;
+ typec_set_pwr_role(anx7688->port, anx7688->pwr_role);
+ typec_set_data_role(anx7688->port, anx7688->data_role);
+ typec_set_pwr_opmode(anx7688->port, TYPEC_PWR_MODE_USB);
+ typec_set_vconn_role(anx7688->port, TYPEC_SINK);
+
+ // make sure BC1.2 detection in PMIC is enabled
+ anx7688->last_bc_result = -1;
+
+ dev_dbg(dev, "enabling USB BC 1.2 detection\n");
+
+ ret = devm_request_irq(dev, irq_cabledet, anx7688_irq_plug_handler,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "anx7688-cabledet", anx7688);
+ if (ret < 0) {
+ dev_err(dev, "Could not request cabledet irq (%d)\n", ret);
+ goto err_cport;
+ }
+
+ ret = devm_request_threaded_irq(dev, client->irq,
+ NULL, anx7688_irq_status_handler,
+ IRQF_ONESHOT, NULL, anx7688);
+ if (ret < 0) {
+ dev_err(dev, "Could not request irq (%d)\n", ret);
+ goto err_cport;
+ }
+
+ anx7688->vbus_in_nb.notifier_call = anx7688_vbus_in_notify;
+ anx7688->vbus_in_nb.priority = 0;
+ ret = power_supply_reg_notifier(&anx7688->vbus_in_nb);
+ if (ret)
+ goto err_cport;
+
+ anx7688->debug_root = debugfs_create_dir("anx7688", NULL);
+ debugfs_create_file("firmware", 0444, anx7688->debug_root, anx7688,
+ &anx7688_firmware_fops);
+ debugfs_create_file("regs", 0444, anx7688->debug_root, anx7688,
+ &anx7688_regs_fops);
+ debugfs_create_file("status", 0444, anx7688->debug_root, anx7688,
+ &anx7688_status_fops);
+
+ schedule_delayed_work(&anx7688->work, msecs_to_jiffies(10));
+
+ timer_setup(&anx7688->work_timer, anx7688_cabledet_timer_fn, 0);
+ mod_timer(&anx7688->work_timer, jiffies + msecs_to_jiffies(1000));
+
+ return 0;
+
+err_cport:
+ typec_unregister_port(anx7688->port);
+err_role_sw:
+ usb_role_switch_put(anx7688->role_sw);
+err_disable_reg:
+ regulator_bulk_disable(ANX7688_NUM_ALWAYS_ON_SUPPLIES, anx7688->supplies);
+err_dummy_dev:
+ i2c_unregister_device(anx7688->client_tcpc);
+ return ret;
+}
+
+static void anx7688_i2c_remove(struct i2c_client *client)
+{
+ struct anx7688 *anx7688 = i2c_get_clientdata(client);
+
+ mutex_lock(&anx7688->lock);
+
+ power_supply_unreg_notifier(&anx7688->vbus_in_nb);
+
+ del_timer_sync(&anx7688->work_timer);
+
+ cancel_delayed_work_sync(&anx7688->work);
+
+ if (test_bit(ANX7688_F_CONNECTED, anx7688->flags))
+ anx7688_disconnect(anx7688);
+
+ typec_unregister_partner(anx7688->partner);
+ typec_unregister_port(anx7688->port);
+ usb_role_switch_put(anx7688->role_sw);
+
+ regulator_bulk_disable(ANX7688_NUM_ALWAYS_ON_SUPPLIES, anx7688->supplies);
+ i2c_unregister_device(anx7688->client_tcpc);
+
+ debugfs_remove(anx7688->debug_root);
+
+ mutex_unlock(&anx7688->lock);
+}
+
+static int __maybe_unused anx7688_suspend(struct device *dev)
+{
+ struct anx7688 *anx7688 = i2c_get_clientdata(to_i2c_client(dev));
+
+ del_timer_sync(&anx7688->work_timer);
+ cancel_delayed_work_sync(&anx7688->work);
+
+ regulator_disable(anx7688->supplies[ANX7688_I2C_INDEX].consumer);
+
+ return 0;
+}
+
+static int __maybe_unused anx7688_resume(struct device *dev)
+{
+ struct anx7688 *anx7688 = i2c_get_clientdata(to_i2c_client(dev));
+ int ret;
+
+ ret = regulator_enable(anx7688->supplies[ANX7688_I2C_INDEX].consumer);
+ if (ret)
+ dev_warn(anx7688->dev,
+ "failed to enable I2C regulator (%d)\n", ret);
+
+ // check status right after resume, since it could have changed during
+ // sleep
+ schedule_delayed_work(&anx7688->work, msecs_to_jiffies(50));
+ mod_timer(&anx7688->work_timer, jiffies + msecs_to_jiffies(1000));
+
+ return 0;
+}
+
+static const struct dev_pm_ops anx7688_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(anx7688_suspend, anx7688_resume)
+};
+
+static const struct i2c_device_id anx7688_ids[] = {
+ { "anx7688", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, anx7688_ids);
+
+static struct of_device_id anx7688_of_match_table[] = {
+ { .compatible = "analogix,anx7688" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, anx7688_of_match_table);
+
+static struct i2c_driver anx7688_driver = {
+ .driver = {
+ .name = "anx7688",
+ .of_match_table = anx7688_of_match_table,
+ .pm = &anx7688_pm_ops,
+ },
+ .probe = anx7688_i2c_probe,
+ .remove = anx7688_i2c_remove,
+ .id_table = anx7688_ids,
+};
+
+module_i2c_driver(anx7688_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Martijn Braam <[email protected]>");
+MODULE_AUTHOR("Ondrej Jirman <[email protected]>");
+MODULE_DESCRIPTION("Analogix ANX7688 USB-C DisplayPort bridge");
On Thu, Feb 01, 2024 at 11:41:56AM +0100, Pavel Machek wrote:
> --- /dev/null
> +++ b/drivers/usb/typec/anx7688.c
> @@ -0,0 +1,1866 @@
> +/*
> + * ANX7688 USB-C HDMI bridge/PD driver
> + *
<snip>
Did this pass checkpatch? I need a spdx line for new files please,
don't force us to go back and guess in the future, that isn't nice.
thanks,
greg k-h
On Thu, Feb 01, 2024 at 11:41:56AM +0100, Pavel Machek wrote:
> +#define DEBUG
Please don't. This is dynamic, use the dynamic debugging and set it
from userspace if you want to debug the driver.
> +
> +#include <linux/debugfs.h>
> +#include <linux/delay.h>
> +#include <linux/extcon-provider.h>
> +#include <linux/firmware.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/irqreturn.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of_irq.h>
> +#include <linux/power_supply.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/usb/pd.h>
> +#include <linux/usb/role.h>
> +#include <linux/usb/typec.h>
> +
> +/* firmware regs */
> +
> +#define ANX7688_REG_VBUS_OFF_DELAY_TIME 0x22
> +#define ANX7688_REG_FEATURE_CTRL 0x27
> +#define ANX7688_REG_EEPROM_LOAD_STATUS1 0x11
> +#define ANX7688_REG_EEPROM_LOAD_STATUS0 0x12
> +#define ANX7688_REG_FW_VERSION1 0x15
> +#define ANX7688_REG_FW_VERSION0 0x16
> +
> +#define ANX7688_EEPROM_FW_LOADED 0x01
Mix of tabs and spaces, please just use tabs.
> +static const char * const anx7688_supply_names[] = {
> + "avdd33",
> + "avdd18",
> + "dvdd18",
> + "avdd10",
> + "dvdd10",
> + "i2c",
> + "hdmi_vt",
> +
> + "vconn", // power for VCONN1/VCONN2 switches
> + "vbus", // vbus power
> +};
Again, tabs vs. spaces, please use checkpatch.
> +#define ANX7688_NUM_SUPPLIES ARRAY_SIZE(anx7688_supply_names)
> +#define ANX7688_NUM_ALWAYS_ON_SUPPLIES (ANX7688_NUM_SUPPLIES - 1)
> +
> +#define ANX7688_I2C_INDEX (ANX7688_NUM_SUPPLIES - 4)
> +#define ANX7688_VCONN_INDEX (ANX7688_NUM_SUPPLIES - 2)
> +#define ANX7688_VBUS_INDEX (ANX7688_NUM_SUPPLIES - 1)
> +
> +enum {
> + ANX7688_F_POWERED,
> + ANX7688_F_CONNECTED,
> + ANX7688_F_FW_FAILED,
> + ANX7688_F_PWRSUPPLY_CHANGE,
> + ANX7688_F_CURRENT_UPDATE,
> +};
> +
> +struct anx7688 {
> + struct device *dev;
> + struct i2c_client *client;
> + struct i2c_client *client_tcpc;
> + struct regulator_bulk_data supplies[ANX7688_NUM_SUPPLIES];
> + struct power_supply *vbus_in_supply;
> + struct notifier_block vbus_in_nb;
> + int input_current_limit; // mA
> + struct gpio_desc *gpio_enable;
> + struct gpio_desc *gpio_reset;
> + struct gpio_desc *gpio_cabledet;
I'm stopping here, again, tabs, you know this :(
greg k-h
Hi!
> > --- /dev/null
> > +++ b/drivers/usb/typec/anx7688.c
> > @@ -0,0 +1,1866 @@
> > +/*
> > + * ANX7688 USB-C HDMI bridge/PD driver
> > + *
>
> <snip>
>
> Did this pass checkpatch? I need a spdx line for new files please,
> don't force us to go back and guess in the future, that isn't nice.
Thanks for the review. Fixing checkpatch issues is easy, but it looks
like closer look will be needed at the devicetree probing.
Also, what are the authors preferences about the license? I'd prefer
GPLv2+.
Best regards,
Pavel
Hi Pavel,
On Thu, Feb 01, 2024 at 11:41:56AM +0100, Pavel Machek wrote:
> From: Ondrej Jirman <[email protected]>
>
> This is driver for ANX7688 USB-C HDMI, with flashing and debugging
> features removed. ANX7688 is rather criticial piece on PinePhone,
> there's no display and no battery charging without it.
Don't remove the flashing part. Some Pinephones come without the firmware
in the past. Even recently, I've seen some people in the Pine chat
asking how to flash the firmware on some old PinePhone.
It's a safe operation that can be done at any time and can only be done
from the kernel driver.
> There's likely more work to be done here, but having basic support
> in mainline is needed to be able to work on the other stuff
> (networking, cameras, power management).
>
> Signed-off-by: Ondrej Jirman <[email protected]>
I should be second in order of sign-offs. Martijn wrote a non-working skeleton
https://megous.com/git/linux/commit/?h=pp-5.7&id=30e33cefd7956a2b49fb27008b4af9d868974e58
driver. Then I picked it up and developed it over years to a working thing.
Almost none of the skeleton remains.
License is GPLv2.
> Signed-off-by: Martijn Braam <[email protected]>
> Signed-off-by: Samuel Holland <[email protected]>
> Signed-off-by: Pavel Machek <[email protected]>
>
> [...]
>
> +static int anx7688_i2c_probe(struct i2c_client *client)
> +{
> + struct anx7688 *anx7688;
> + struct device *dev = &client->dev;
> + struct typec_capability typec_cap = { };
> + int i, vid_h, vid_l;
> + int irq_cabledet;
> + int ret = 0;
> +
> + anx7688 = devm_kzalloc(dev, sizeof(*anx7688), GFP_KERNEL);
> + if (!anx7688)
> + return -ENOMEM;
> +
> + i2c_set_clientdata(client, anx7688);
> + anx7688->client = client;
> + anx7688->dev = &client->dev;
> + mutex_init(&anx7688->lock);
> + INIT_DELAYED_WORK(&anx7688->work, anx7688_work);
> + anx7688->last_extcon_state = -1;
> +
> + ret = of_property_read_variable_u32_array(dev->of_node, "source-caps",
> + anx7688->src_caps,
> + 1, ARRAY_SIZE(anx7688->src_caps));
> + if (ret < 0) {
> + dev_err(dev, "failed to get source-caps from DT\n");
> + return ret;
> + }
> + anx7688->n_src_caps = ret;
> +
> + ret = of_property_read_variable_u32_array(dev->of_node, "sink-caps",
> + anx7688->snk_caps,
> + 1, ARRAY_SIZE(anx7688->snk_caps));
> + if (ret < 0) {
> + dev_err(dev, "failed to get sink-caps from DT\n");
> + return ret;
> + }
^^^ The driver will need to follow usb-c-connector bindings and it will need
a bindings documentation for itself.
That's one of the missing things that I did not implement, yet.
Kind regards,
o.
Hi!
> > From: Ondrej Jirman <[email protected]>
> >
> > This is driver for ANX7688 USB-C HDMI, with flashing and debugging
> > features removed. ANX7688 is rather criticial piece on PinePhone,
> > there's no display and no battery charging without it.
>
> Don't remove the flashing part. Some Pinephones come without the firmware
> in the past. Even recently, I've seen some people in the Pine chat
> asking how to flash the firmware on some old PinePhone.
>
> It's a safe operation that can be done at any time and can only be done
> from the kernel driver.
I can re-add it later, but initial merge will be tricky enough as-is.
> > There's likely more work to be done here, but having basic support
> > in mainline is needed to be able to work on the other stuff
> > (networking, cameras, power management).
> >
> > Signed-off-by: Ondrej Jirman <[email protected]>
>
> I should be second in order of sign-offs. Martijn wrote a non-working skeleton
> https://megous.com/git/linux/commit/?h=pp-5.7&id=30e33cefd7956a2b49fb27008b4af9d868974e58
> driver. Then I picked it up and developed it over years to a working thing.
> Almost none of the skeleton remains.
I believe From: should match First signed-off. I guess Martijn should
be marked as co-developed-by or something like that?
> License is GPLv2.
Ok.
> > + ret = of_property_read_variable_u32_array(dev->of_node, "sink-caps",
> > + anx7688->snk_caps,
> > + 1, ARRAY_SIZE(anx7688->snk_caps));
> > + if (ret < 0) {
> > + dev_err(dev, "failed to get sink-caps from DT\n");
> > + return ret;
> > + }
>
> ^^^ The driver will need to follow usb-c-connector bindings and it will need
> a bindings documentation for itself.
>
> That's one of the missing things that I did not implement, yet.
Yep, I fought with device trees for few days. I should have yaml
ready.
Best regards,
Pavel
--
People of Russia, stop Putin before his war on Ukraine escalates.