I have a pci backplane extender, with 4 cards
(named piraq) in it. The cards are detected by
the PCI system, and irqs 92-95 are assigned,
as shown in /var/log/messages:
kernel: PCI->APIC IRQ transform: (B6,I4,P0) -> 93
kernel: PCI->APIC IRQ transform: (B6,I6,P0) -> 95
kernel: PCI->APIC IRQ transform: (B6,I7,P0) -> 92
kernel: PCI->APIC IRQ transform: (B6,I9,P0) -> 94
My driver loads happily, with succesful registering
of these interrupts. However, the interrupts don't
get handled properly, and /proc/interrupts shows that
they have not been correctly setup:
CPU0 CPU1
0: 4946 10162 IO-APIC-edge timer
1: 53 131 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
8: 1 0 IO-APIC-edge rtc
12: 4816 0 IO-APIC-edge PS/2 Mouse
15: 903 1 IO-APIC-edge ide1
16: 0 0 IO-APIC-level usb-uhci
18: 0 0 IO-APIC-level usb-uhci
19: 0 0 IO-APIC-level usb-uhci
20: 3 0 IO-APIC-level ohci1394
23: 0 0 IO-APIC-level ehci_hcd
24: 748 0 IO-APIC-level eth0
25: 43 0 IO-APIC-level ioc0
26: 43 0 IO-APIC-level ioc1
50: 9142 4235 IO-APIC-level ioc2
92: 0 0 none piraq
93: 0 0 none piraq
94: 0 0 none piraq
95: 0 0 none piraq
NMI: 0 0
LOC: 15017 15016
ERR: 0
MIS: 0
If I boot with "noapic", the interrupts do get
assigned to XT-PIC, and will trigger correctly.
Same results are seen in 2.4.22 and 2.6.0-test9.
Thanks,
Charlie
N.B. System is Dell 650 w/ dual Xeons.
Backplane extender is a Magma. This scheme uses
a PCI interconnect card in both the Dell and
the Magma, with a connecting cable.
On Mon, 3 Nov 2003, Charles Martin wrote:
>
> I have a pci backplane extender, with 4 cards
> (named piraq) in it. The cards are detected by
> the PCI system, and irqs 92-95 are assigned,
> as shown in /var/log/messages:
>
> kernel: PCI->APIC IRQ transform: (B6,I4,P0) -> 93
> kernel: PCI->APIC IRQ transform: (B6,I6,P0) -> 95
> kernel: PCI->APIC IRQ transform: (B6,I7,P0) -> 92
> kernel: PCI->APIC IRQ transform: (B6,I9,P0) -> 94
Can you enable APIC_DEBUG debugging in "include/asm-i386/apic.h", and make
sure that you build the kernel with a big printk buffer. Then, in case
your distribution comes with a broken "dmesg" binary that doesn't show
more than about 20kB of data, compile this trivial program and run it
after bootup, and send the whole log out..
It would be a pity to have to boot with "noapic", since this is exactly
the kind of situation where you _want_ the extra interrupts.
Linus
- stupid-dmesg.c -
#include <sys/klog.h>
int main(int argc, char **argv)
{
static char buffer[128*1024];
int i;
i = klogctl(3, buffer, sizeof(buffer));
if (i > 0)
write(1, buffer, i);
}
> -----Original Message-----
> From: Linus Torvalds [mailto:[email protected]]
> Sent: Monday, November 03, 2003 10:04 AM
> To: Charles Martin
> Cc: [email protected]
> Subject: Re: interrupts across PCI bridge(s) not handled
>
>
>
> On Mon, 3 Nov 2003, Charles Martin wrote:
> >
> > I have a pci backplane extender, with 4 cards
> > (named piraq) in it. The cards are detected by
> > the PCI system, and irqs 92-95 are assigned,
> > as shown in /var/log/messages:
> >
> > kernel: PCI->APIC IRQ transform: (B6,I4,P0) -> 93
> > kernel: PCI->APIC IRQ transform: (B6,I6,P0) -> 95
> > kernel: PCI->APIC IRQ transform: (B6,I7,P0) -> 92
> > kernel: PCI->APIC IRQ transform: (B6,I9,P0) -> 94
>
> Can you enable APIC_DEBUG debugging in
> "include/asm-i386/apic.h", and make
> sure that you build the kernel with a big printk buffer.
> Then, in case
> your distribution comes with a broken "dmesg" binary that
> doesn't show
> more than about 20kB of data, compile this trivial program and run it
> after bootup, and send the whole log out..
>
> It would be a pity to have to boot with "noapic", since this
> is exactly
> the kind of situation where you _want_ the extra interrupts.
>
> Linus
>
> - stupid-dmesg.c -
> #include <sys/klog.h>
>
> int main(int argc, char **argv)
> {
> static char buffer[128*1024];
> int i;
>
> i = klogctl(3, buffer, sizeof(buffer));
> if (i > 0)
> write(1, buffer, i);
> }
>
>
I enabled APIC_DEBUG, and here is the dmesg output.
Thanks,
Charlie
<4>Linux version 2.4.22smp ([email protected]) (gcc version
3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #24 SMP Mon Nov 3 13:22:46 CST
2003
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000007ff75000 (usable)
<4> BIOS-e820: 000000007ff75000 - 000000007ff77000 (ACPI NVS)
<4> BIOS-e820: 000000007ff77000 - 000000007ff98000 (ACPI data)
<4> BIOS-e820: 000000007ff98000 - 0000000080000000 (reserved)
<4> BIOS-e820: 00000000fec00000 - 00000000fec90000 (reserved)
<4> BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
<4> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
<5>1151MB HIGHMEM available.
<5>896MB LOWMEM available.
<4>Scan SMP from c0000000 for 1024 bytes.
<4>Scan SMP from c009fc00 for 1024 bytes.
<4>Scan SMP from c00f0000 for 65536 bytes.
<4>found SMP MP-table at 000fe710
<4>hm, page 000fe000 reserved twice.
<4>hm, page 000ff000 reserved twice.
<4>hm, page 000f0000 reserved twice.
<4>On node 0 totalpages: 524149
<4>zone(0): 4096 pages.
<4>zone(1): 225280 pages.
<4>zone(2): 294773 pages.
<4>Intel MultiProcessor Specification v1.4
<4> Virtual Wire compatibility mode.
<4>OEM ID: DELL Product ID: WS 650 APIC at: 0xFEE00000
<4>Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
<4> Floating point unit present.
<4> Machine Exception supported.
<4> 64 bit compare & exchange supported.
<4> Internal APIC present.
<4> SEP present.
<4> MTRR present.
<4> PGE present.
<4> MCA present.
<4> CMOV present.
<4> PAT present.
<4> PSE present.
<4> Cache Line Flush Instruction present.
<4> Debug Trace and EMON Store present.
<4> ACPI Thermal Throttle Registers present.
<4> MMX present.
<4> FXSR present.
<4> XMM present.
<4> Willamette New Instructions present.
<4> Self Snoop present.
<4> HT present.
<4> Thermal Monitor present.
<4> Bootup CPU
<4>Processor #6 Pentium 4(tm) XEON(tm) APIC version 20
<4> Floating point unit present.
<4> Machine Exception supported.
<4> 64 bit compare & exchange supported.
<4> Internal APIC present.
<4> SEP present.
<4> MTRR present.
<4> PGE present.
<4> MCA present.
<4> CMOV present.
<4> PAT present.
<4> PSE present.
<4> Cache Line Flush Instruction present.
<4> Debug Trace and EMON Store present.
<4> ACPI Thermal Throttle Registers present.
<4> MMX present.
<4> FXSR present.
<4> XMM present.
<4> Willamette New Instructions present.
<4> Self Snoop present.
<4> HT present.
<4> Thermal Monitor present.
<4>Bus #0 is PCI
<4>Bus #1 is PCI
<4>Bus #2 is PCI
<4>Bus #3 is PCI
<4>Bus #4 is PCI
<4>Bus #5 is PCI
<4>Bus #6 is PCI
<4>Bus #7 is PCI
<4>Bus #8 is ISA
<4>I/O APIC #8 Version 32 at 0xFEC00000.
<4>I/O APIC #10 Version 32 at 0xFEC80000.
<4>I/O APIC #9 Version 32 at 0xFEC80800.
<4>Int: type 3, pol 1, trig 1, bus 8, IRQ 00, APIC ID 8, APIC INT 00
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 01, APIC ID 8, APIC INT 01
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 00, APIC ID 8, APIC INT 02
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 03, APIC ID 8, APIC INT 03
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 04, APIC ID 8, APIC INT 04
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 05, APIC ID 8, APIC INT 05
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 06, APIC ID 8, APIC INT 06
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 07, APIC ID 8, APIC INT 07
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 08, APIC ID 8, APIC INT 08
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 09, APIC ID 8, APIC INT 09
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 0a, APIC ID 8, APIC INT 0a
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 0b, APIC ID 8, APIC INT 0b
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 0c, APIC ID 8, APIC INT 0c
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 0e, APIC ID 8, APIC INT 0e
<4>Int: type 0, pol 0, trig 0, bus 8, IRQ 0f, APIC ID 8, APIC INT 0f
<4>Int: type 0, pol 0, trig 0, bus 0, IRQ 74, APIC ID 8, APIC INT 10
<4>Int: type 0, pol 0, trig 0, bus 1, IRQ 00, APIC ID 8, APIC INT 10
<4>Int: type 0, pol 0, trig 0, bus 0, IRQ 7d, APIC ID 8, APIC INT 11
<4>Int: type 0, pol 0, trig 0, bus 1, IRQ 01, APIC ID 8, APIC INT 11
<4>Int: type 0, pol 0, trig 0, bus 0, IRQ 7c, APIC ID 8, APIC INT 12
<4>Int: type 0, pol 0, trig 0, bus 0, IRQ 76, APIC ID 8, APIC INT 12
<4>Int: type 0, pol 0, trig 0, bus 0, IRQ 75, APIC ID 8, APIC INT 13
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 30, APIC ID 8, APIC INT 14
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 37, APIC ID 8, APIC INT 14
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 3a, APIC ID 8, APIC INT 14
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 1c, APIC ID 0, APIC INT 14
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 34, APIC ID 8, APIC INT 15
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 3b, APIC ID 8, APIC INT 15
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 10, APIC ID 0, APIC INT 15
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 35, APIC ID 8, APIC INT 16
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 38, APIC ID 8, APIC INT 16
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 24, APIC ID 0, APIC INT 16
<4>Int: type 0, pol 0, trig 0, bus 0, IRQ 77, APIC ID 8, APIC INT 17
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 36, APIC ID 8, APIC INT 17
<4>Int: type 0, pol 0, trig 0, bus 7, IRQ 39, APIC ID 8, APIC INT 17
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 18, APIC ID 0, APIC INT 17
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 38, APIC ID a, APIC INT 00
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 1c, APIC ID 0, APIC INT 00
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 30, APIC ID a, APIC INT 01
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 10, APIC ID 0, APIC INT 01
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 31, APIC ID a, APIC INT 02
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 24, APIC ID 0, APIC INT 02
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 32, APIC ID a, APIC INT 03
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 18, APIC ID 0, APIC INT 03
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 33, APIC ID a, APIC INT 04
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 34, APIC ID a, APIC INT 05
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 35, APIC ID a, APIC INT 06
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 36, APIC ID a, APIC INT 07
<4>Int: type 0, pol 0, trig 0, bus 3, IRQ 37, APIC ID a, APIC INT 08
<4>Int: type 0, pol 0, trig 0, bus 4, IRQ 34, APIC ID 9, APIC INT 00
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 1c, APIC ID 0, APIC INT 00
<4>Int: type 0, pol 0, trig 0, bus 4, IRQ 35, APIC ID 9, APIC INT 01
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 10, APIC ID 0, APIC INT 01
<4>Int: type 0, pol 0, trig 0, bus 4, IRQ 38, APIC ID 9, APIC INT 02
<4>Int: type 0, pol 0, trig 0, bus 4, IRQ 36, APIC ID 9, APIC INT 02
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 24, APIC ID 0, APIC INT 02
<4>Int: type 0, pol 0, trig 0, bus 4, IRQ 37, APIC ID 9, APIC INT 03
<4>Int: type 0, pol 0, trig 0, bus 6, IRQ 18, APIC ID 0, APIC INT 03
<4>Lint: type 3, pol 1, trig 1, bus 8, IRQ 00, APIC ID ff, APIC LINT 00
<4>Lint: type 1, pol 1, trig 1, bus 8, IRQ 00, APIC ID ff, APIC LINT 01
<4>Enabling APIC mode: Flat. Using 3 I/O APICs
<4>Processors: 2
<4>Kernel command line: ro root=LABEL=/ apic
<4>mapped APIC to ffffe000 (fee00000)
<4>mapped IOAPIC to ffffd000 (fec00000)
<4>mapped IOAPIC to ffffc000 (fec80000)
<4>mapped IOAPIC to ffffb000 (fec80800)
<6>Initializing CPU#0
<4>Detected 2392.343 MHz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 4771.02 BogoMIPS
<6>Memory: 2065960k/2096596k available (3174k kernel code, 30252k
reserved, 1150k data, 392k init, 1179092k highmem)
<6>Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
<6>Inode cache hash table entries: 131072 (order: 8, 1048576 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<6>Buffer cache hash table entries: 131072 (order: 7, 524288 bytes)
<4>Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch ([email protected])
<4>mtrr: detected mtrr type: Intel
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<4>CPU0: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09
<4>per-CPU timeslice cutoff: 1462.89 usecs.
<4>Getting VERSION: 50014
<4>Getting VERSION: 50014
<4>Getting ID: 0
<4>Getting ID: f000000
<4>Getting LVT0: 700
<4>Getting LVT1: 400
<4>enabled ExtINT on CPU#0
<4>ESR value before enabling vector: 00000040
<4>ESR value after enabling vector: 00000000
<4>CPU present map: 41
<4>Booting processor 1/6 eip 2000
<4>Setting warm reset code and vector.
<4>1.
<4>2.
<4>3.
<4>Asserting INIT.
<4>Waiting for send to finish...
<4>+Deasserting INIT.
<4>Waiting for send to finish...
<4>+#startup loops: 2.
<4>Sending STARTUP #1.
<4>After apic_write.
<6>Initializing CPU#1
<4>CPU#1 (phys ID: 6) waiting for CALLOUT
<4>Startup point 1.
<4>Waiting for send to finish...
<4>+Sending STARTUP #2.
<4>After apic_write.
<4>Startup point 1.
<4>Waiting for send to finish...
<4>+After Startup.
<4>Before Callout 1.
<4>After Callout 1.
<4>CALLIN, before setup_local_APIC().
<4>masked ExtINT on CPU#1
<4>ESR value before enabling vector: 00000000
<4>ESR value after enabling vector: 00000000
<4>Calibrating delay loop... 4784.12 BogoMIPS
<4>Stack at about f7ffbfb0
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 3
<6>Intel machine check reporting enabled on CPU#1.
<7>CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU: Common caps: bfebfbff 00000000 00000000 00000000
<4>OK.
<4>CPU1: Intel(R) Xeon(TM) CPU 2.40GHz stepping 09
<4>CPU has booted.
<4>Before bogomips.
<6>Total of 2 processors activated (9555.14 BogoMIPS).
<4>Before bogocount - setting activated=1.
<4>Boot done.
<4>WARNING: No sibling found for CPU 0.
<4>WARNING: No sibling found for CPU 1.
<4>ENABLING IO-APIC IRQs
<4>Setting 8 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 8 ... ok.
<4>Setting 10 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 10 ... ok.
<4>Setting 9 in the phys_id_present_map
<6>...changing IO-APIC physical APIC ID to 9 ... ok.
<4>Synchronizing Arb IDs.
<7>init IO_APIC IRQs
<7> IO-APIC (apicid-pin) 8-0, 8-13, 10-9, 10-10, 10-11, 10-12, 10-13,
10-14, 10-15, 10-16, 10-17, 10-18, 10-19, 10-20, 10-21, 10-22, 10-23,
9-4, 9-5, 9-6, 9-7, 9-8, 9-9, 9-10, 9-11, 9-12, 9-13, 9-14, 9-15, 9-16,
9-17, 9-18, 9-19, 9-20, 9-21, 9-22, 9-23 not connected.
<6>..TIMER: vector=0x31 pin1=2 pin2=0
<7>number of MP IRQ sources: 58.
<7>number of IO-APIC #8 registers: 24.
<7>number of IO-APIC #10 registers: 24.
<7>number of IO-APIC #9 registers: 24.
<6>testing the IO APIC.......................
<4>
<7>IO APIC #8......
<7>.... register #00: 08000000
<7>....... : physical APIC id: 08
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 00000000
<7>....... : arbitration: 00
<7>.... register #03: 00000001
<7>....... : Boot DT : 1
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 000 00 1 0 0 0 0 0 0 00
<7> 01 003 03 0 0 0 0 0 1 1 39
<7> 02 003 03 0 0 0 0 0 1 1 31
<7> 03 003 03 0 0 0 0 0 1 1 41
<7> 04 003 03 0 0 0 0 0 1 1 49
<7> 05 003 03 0 0 0 0 0 1 1 51
<7> 06 003 03 0 0 0 0 0 1 1 59
<7> 07 003 03 0 0 0 0 0 1 1 61
<7> 08 003 03 0 0 0 0 0 1 1 69
<7> 09 003 03 0 0 0 0 0 1 1 71
<7> 0a 003 03 0 0 0 0 0 1 1 79
<7> 0b 003 03 0 0 0 0 0 1 1 81
<7> 0c 003 03 0 0 0 0 0 1 1 89
<7> 0d 000 00 1 0 0 0 0 0 0 00
<7> 0e 003 03 0 0 0 0 0 1 1 91
<7> 0f 003 03 0 0 0 0 0 1 1 99
<7> 10 003 03 1 1 0 1 0 1 1 A1
<7> 11 003 03 1 1 0 1 0 1 1 A9
<7> 12 003 03 1 1 0 1 0 1 1 B1
<7> 13 003 03 1 1 0 1 0 1 1 B9
<7> 14 003 03 1 1 0 1 0 1 1 C1
<7> 15 003 03 1 1 0 1 0 1 1 C9
<7> 16 003 03 1 1 0 1 0 1 1 D1
<7> 17 003 03 1 1 0 1 0 1 1 D9
<4>
<7>IO APIC #10......
<7>.... register #00: 0A000000
<7>....... : physical APIC id: 0A
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 0A000000
<7>....... : arbitration: 0A
<7>.... register #03: 00000001
<7>....... : Boot DT : 1
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 003 03 1 1 0 1 0 1 1 E1
<7> 01 003 03 1 1 0 1 0 1 1 E9
<7> 02 003 03 1 1 0 1 0 1 1 32
<7> 03 003 03 1 1 0 1 0 1 1 3A
<7> 04 003 03 1 1 0 1 0 1 1 42
<7> 05 003 03 1 1 0 1 0 1 1 4A
<7> 06 003 03 1 1 0 1 0 1 1 52
<7> 07 003 03 1 1 0 1 0 1 1 5A
<7> 08 003 03 1 1 0 1 0 1 1 62
<7> 09 000 00 1 0 0 0 0 0 0 00
<7> 0a 000 00 1 0 0 0 0 0 0 00
<7> 0b 000 00 1 0 0 0 0 0 0 00
<7> 0c 000 00 1 0 0 0 0 0 0 00
<7> 0d 000 00 1 0 0 0 0 0 0 00
<7> 0e 000 00 1 0 0 0 0 0 0 00
<7> 0f 000 00 1 0 0 0 0 0 0 00
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<4>
<7>IO APIC #9......
<7>.... register #00: 09000000
<7>....... : physical APIC id: 09
<7>....... : Delivery Type: 0
<7>....... : LTS : 0
<7>.... register #01: 00178020
<7>....... : max redirection entries: 0017
<7>....... : PRQ implemented: 1
<7>....... : IO APIC version: 0020
<7>.... register #02: 09000000
<7>....... : arbitration: 09
<7>.... register #03: 00000001
<7>....... : Boot DT : 1
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<7> 00 003 03 1 1 0 1 0 1 1 6A
<7> 01 003 03 1 1 0 1 0 1 1 72
<7> 02 003 03 1 1 0 1 0 1 1 7A
<7> 03 003 03 1 1 0 1 0 1 1 82
<7> 04 000 00 1 0 0 0 0 0 0 00
<7> 05 000 00 1 0 0 0 0 0 0 00
<7> 06 000 00 1 0 0 0 0 0 0 00
<7> 07 000 00 1 0 0 0 0 0 0 00
<7> 08 000 00 1 0 0 0 0 0 0 00
<7> 09 000 00 1 0 0 0 0 0 0 00
<7> 0a 000 00 1 0 0 0 0 0 0 00
<7> 0b 000 00 1 0 0 0 0 0 0 00
<7> 0c 000 00 1 0 0 0 0 0 0 00
<7> 0d 000 00 1 0 0 0 0 0 0 00
<7> 0e 000 00 1 0 0 0 0 0 0 00
<7> 0f 000 00 1 0 0 0 0 0 0 00
<7> 10 000 00 1 0 0 0 0 0 0 00
<7> 11 000 00 1 0 0 0 0 0 0 00
<7> 12 000 00 1 0 0 0 0 0 0 00
<7> 13 000 00 1 0 0 0 0 0 0 00
<7> 14 000 00 1 0 0 0 0 0 0 00
<7> 15 000 00 1 0 0 0 0 0 0 00
<7> 16 000 00 1 0 0 0 0 0 0 00
<7> 17 000 00 1 0 0 0 0 0 0 00
<7>IRQ to pin mappings:
<7>IRQ0 -> 0:2
<7>IRQ1 -> 0:1
<7>IRQ3 -> 0:3
<7>IRQ4 -> 0:4
<7>IRQ5 -> 0:5
<7>IRQ6 -> 0:6
<7>IRQ7 -> 0:7
<7>IRQ8 -> 0:8
<7>IRQ9 -> 0:9
<7>IRQ10 -> 0:10
<7>IRQ11 -> 0:11
<7>IRQ12 -> 0:12
<7>IRQ14 -> 0:14
<7>IRQ15 -> 0:15
<7>IRQ16 -> 0:16
<7>IRQ17 -> 0:17
<7>IRQ18 -> 0:18
<7>IRQ19 -> 0:19
<7>IRQ20 -> 0:20
<7>IRQ21 -> 0:21
<7>IRQ22 -> 0:22
<7>IRQ23 -> 0:23
<7>IRQ24 -> 1:0
<7>IRQ25 -> 1:1
<7>IRQ26 -> 1:2
<7>IRQ27 -> 1:3
<7>IRQ28 -> 1:4
<7>IRQ29 -> 1:5
<7>IRQ30 -> 1:6
<7>IRQ31 -> 1:7
<7>IRQ32 -> 1:8
<7>IRQ48 -> 2:0
<7>IRQ49 -> 2:1
<7>IRQ50 -> 2:2
<7>IRQ51 -> 2:3
<6>.................................... done.
<4>Using local APIC timer interrupts.
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 2392.2463 MHz.
<4>..... host bus clock speed is 132.9025 MHz.
<4>cpu: 0, clocks: 1329025, slice: 443008
<4>CPU0<T0:1329024,T1:886016,D:0,S:443008,C:1329025>
<4>cpu: 1, clocks: 1329025, slice: 443008
<4>CPU1<T0:1329024,T1:443008,D:0,S:443008,C:1329025>
<4>checking TSC synchronization across CPUs: passed.
<4>Setting commenced=1, go go go
<4>Waiting on wait_init_idle (map = 0x2)
<4>All processors have done init_idle
<6>PCI: PCI BIOS revision 2.10 entry at 0xfbdd5, last bus=7
<6>PCI: Using configuration type 1
<6>PCI: Probing PCI hardware
<4>PCI: Probing PCI hardware (bus 00)
<6>PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
<4>Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
<6>PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
<4>querying PCI -> IRQ mapping bus:0, slot:29, pin:0.
<6>PCI->APIC IRQ transform: (B0,I29,P0) -> 16
<4>querying PCI -> IRQ mapping bus:0, slot:29, pin:1.
<6>PCI->APIC IRQ transform: (B0,I29,P1) -> 19
<4>querying PCI -> IRQ mapping bus:0, slot:29, pin:2.
<6>PCI->APIC IRQ transform: (B0,I29,P2) -> 18
<4>querying PCI -> IRQ mapping bus:0, slot:29, pin:3.
<6>PCI->APIC IRQ transform: (B0,I29,P3) -> 23
<4>querying PCI -> IRQ mapping bus:0, slot:31, pin:0.
<6>PCI->APIC IRQ transform: (B0,I31,P0) -> 18
<4>querying PCI -> IRQ mapping bus:0, slot:31, pin:1.
<6>PCI->APIC IRQ transform: (B0,I31,P1) -> 17
<4>querying PCI -> IRQ mapping bus:0, slot:31, pin:1.
<6>PCI->APIC IRQ transform: (B0,I31,P1) -> 17
<4>querying PCI -> IRQ mapping bus:1, slot:0, pin:0.
<6>PCI->APIC IRQ transform: (B1,I0,P0) -> 16
<4>querying PCI -> IRQ mapping bus:3, slot:12, pin:0.
<6>PCI->APIC IRQ transform: (B3,I12,P0) -> 25
<4>querying PCI -> IRQ mapping bus:3, slot:12, pin:1.
<6>PCI->APIC IRQ transform: (B3,I12,P1) -> 26
<4>querying PCI -> IRQ mapping bus:3, slot:14, pin:0.
<6>PCI->APIC IRQ transform: (B3,I14,P0) -> 24
<4>querying PCI -> IRQ mapping bus:4, slot:14, pin:0.
<6>PCI->APIC IRQ transform: (B4,I14,P0) -> 50
<4>querying PCI -> IRQ mapping bus:6, slot:4, pin:0.
<6>PCI->APIC IRQ transform: (B6,I4,P0) -> 93
<4>querying PCI -> IRQ mapping bus:6, slot:6, pin:0.
<6>PCI->APIC IRQ transform: (B6,I6,P0) -> 95
<4>querying PCI -> IRQ mapping bus:6, slot:7, pin:0.
<6>PCI->APIC IRQ transform: (B6,I7,P0) -> 92
<4>querying PCI -> IRQ mapping bus:6, slot:9, pin:0.
<6>PCI->APIC IRQ transform: (B6,I9,P0) -> 94
<4>querying PCI -> IRQ mapping bus:7, slot:12, pin:0.
<6>PCI->APIC IRQ transform: (B7,I12,P0) -> 20
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<6>IA-32 Microcode Update Driver: v1.11 <[email protected]>
<4>Starting kswapd
<4>allocated 32 pages and 32 bhs reserved for the highmem bounces
<6>Journalled Block Device driver loaded
<6>Installing knfsd (copyright (C) 1996 [email protected]).
<6>i2c-core.o: i2c core module
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI ISAPNP enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<6>Real Time Clock Driver v1.10e
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>0 3c515 cards found.
<4>RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
<6>loop: loaded (max 8 devices)
<6>Intel(R) PRO/1000 Network Driver - version 5.1.13-k1
<6>Copyright (c) 1999-2003 Intel Corporation.
<6>eth0: Intel(R) PRO/1000 Network Connection
<6>Linux agpgart interface v0.99 (c) Jeff Hartmann
<6>agpgart: Maximum main memory to use for agp memory: 1919M
<3>agpgart: Unsupported Intel chipset (device id: 2550), you might want
to try agp_try_unsupported=1.
<7>agpgart: no supported devices found.
<6>[drm] Initialized tdfx 1.0.0 20010216 on minor 0
<6>[drm] Initialized radeon 1.1.1 20010405 on minor 1
<3>[drm:drm_init] *ERROR* Cannot initialize the agpgart module.
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
<6>ICH4: IDE controller at PCI slot 00:1f.1
<4>PCI: Enabling device 00:1f.1 (0005 -> 0007)
<6>ICH4: chipset revision 1
<6>ICH4: not 100% native mode: will probe irqs later
<6> ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
<4>hdc: Lite-On LTN486S 48x Max, ATAPI CD/DVD-ROM drive
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hdc: attached ide-cdrom driver.
<6>hdc: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
<6>Uniform CD-ROM driver Revision: 3.12
<6>SCSI subsystem driver Revision: 1.00
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<6>Fusion MPT base driver 2.05.05+
<6>Copyright (c) 1999-2002 LSI Logic Corporation
<6>mptbase: Initiating ioc0 bringup
<6>ioc0: 53C1030: Capabilities={Initiator}
<6>mptbase: Initiating ioc1 bringup
<6>ioc1: 53C1030: Capabilities={Initiator}
<6>mptbase: Initiating ioc2 bringup
<6>ioc2: 53C1030: Capabilities={Initiator}
<6>mptbase: 3 MPT adapters found, 3 installed.
<6>Fusion MPT SCSI Host driver 2.05.05+
<6>scsi0 : ioc0: LSI53C1030, FwRev=01011800h, Ports=1, MaxQ=222, IRQ=25
<6>scsi1 : ioc1: LSI53C1030, FwRev=01011800h, Ports=1, MaxQ=222, IRQ=26
<6>scsi2 : ioc2: LSI53C1030, FwRev=01011800h, Ports=1, MaxQ=222, IRQ=50
<4>blk: queue c28d741c, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LW Rev: DS08
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue c29d461c, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LW Rev: DS08
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue c29d401c, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<4> Vendor: SEAGATE Model: ST3146807LW Rev: DS08
<4> Type: Direct-Access ANSI SCSI revision: 03
<4>blk: queue c29baa1c, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
<6>mptscsih: ioc2: scsi2: Id=0 Lun=0: Queue depth=31
<6>mptscsih: ioc2: scsi2: Id=1 Lun=0: Queue depth=31
<6>mptscsih: ioc2: scsi2: Id=2 Lun=0: Queue depth=31
<4>Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
<4>Attached scsi disk sdb at scsi2, channel 0, id 1, lun 0
<4>Attached scsi disk sdc at scsi2, channel 0, id 2, lun 0
<4>SCSI device sda: 286749480 512-byte hdwr sectors (146816 MB)
<6>Partition check:
<6> sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
<4>SCSI device sdb: 286749480 512-byte hdwr sectors (146816 MB)
<6> sdb: unknown partition table
<4>SCSI device sdc: 286749480 512-byte hdwr sectors (146816 MB)
<6> sdc: unknown partition table
<6>ohci1394: $Rev: 1010 $ Ben Collins <[email protected]>
<6>ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[fd1ff800-fd1fffff]
Max Packet=[2048]
<6>video1394: Installed video1394 module
<6>raw1394: /dev/raw1394 device initialized
<6>sbp2: $Rev: 1010 $ Ben Collins <[email protected]>
<6>es1371: version v0.32 time 12:56:23 Nov 3 2003
<6>usb.c: registered new driver usbdevfs
<6>usb.c: registered new driver hub
<7>PCI: Setting latency timer of device 00:1d.7 to 64
<6>ehci_hcd 00:1d.7: Intel Corp. 82801DB USB2
<6>ehci_hcd 00:1d.7: irq 23, pci mem f8829800
<6>usb.c: new USB bus registered, assigned bus number 1
<6>ehci_hcd 00:1d.7: enabled 64bit PCI DMA
<4>PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by
BIOS/FW.
<4>PCI: 00:1d.7 PCI cache line size corrected to 32.
<6>ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
<6>hub.c: USB hub found
<6>hub.c: 6 ports detected
<7>ieee1394: Host added: ID:BUS[0-00:1023] GUID[83ffffffffffff00]
<6>host/uhci.c: USB Universal Host Controller Interface driver v1.1
<7>PCI: Setting latency timer of device 00:1d.0 to 64
<6>host/uhci.c: USB UHCI at I/O 0xff80, IRQ 16
<6>usb.c: new USB bus registered, assigned bus number 2
<6>hub.c: USB hub found
<6>hub.c: 2 ports detected
<7>PCI: Setting latency timer of device 00:1d.1 to 64
<6>host/uhci.c: USB UHCI at I/O 0xff60, IRQ 19
<6>usb.c: new USB bus registered, assigned bus number 3
<6>hub.c: USB hub found
<6>hub.c: 2 ports detected
<7>PCI: Setting latency timer of device 00:1d.2 to 64
<6>host/uhci.c: USB UHCI at I/O 0xff40, IRQ 18
<6>usb.c: new USB bus registered, assigned bus number 4
<6>hub.c: USB hub found
<6>hub.c: 2 ports detected
<6>usb.c: registered new driver hiddev
<6>usb.c: registered new driver hid
<6>hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
<6>hid-core.c: USB HID support drivers
<6>usb.c: registered new driver usblp
<6>printer.c: v0.11: USB Printer Device Class driver
<6>bluetooth.c: USB Bluetooth support registered
<6>usb.c: registered new driver bluetty
<6>bluetooth.c: USB Bluetooth tty driver v0.13
<6>usb.c: registered new driver serial
<6>usbserial.c: USB Serial support registered for Generic
<6>usbserial.c: USB Serial Driver core v1.4
<6>usbserial.c: USB Serial support registered for Handspring Visor /
Treo / Palm 4.0 / Cli? 4.x
<6>usbserial.c: USB Serial support registered for Sony Cli? 3.5
<6>visor.c: USB HandSpring Visor, Palm m50x, Treo, Sony Cli? driver v1.7
<6>ipaq.c: USB PocketPC PDA driver v0.5
<6>usbserial.c: USB Serial support registered for PocketPC PDA
<6>usbserial.c: USB Serial support registered for Connect Tech -
WhiteHEAT - (prerenumeration)
<6>usbserial.c: USB Serial support registered for Connect Tech -
WhiteHEAT
<6>whiteheat.c: USB ConnectTech WhiteHEAT driver v1.2
<7>ftdi_sio.c: ftdi_init
<6>usbserial.c: USB Serial support registered for FTDI SIO
<6>usbserial.c: USB Serial support registered for FTDI 8U232AM
Compatible
<6>usbserial.c: USB Serial support registered for FTDI FT232BM
Compatible
<6>usbserial.c: USB Serial support registered for USB-UIRT Infrared
Receiver/Transmitter
<6>usbserial.c: USB Serial support registered for Home-Electronics
TIRA-1 IR Transceiver
<6>ftdi_sio.c: v1.3.4:USB FTDI Serial Converters Driver
<6>usbserial.c: USB Serial support registered for Keyspan PDA
<6>usbserial.c: USB Serial support registered for Keyspan PDA -
(prerenumeration)
<6>usbserial.c: USB Serial support registered for Xircom / Entregra PGS
- (prerenumeration)
<6>keyspan_pda.c: USB Keyspan PDA Converter driver v1.1
<6>usbserial.c: USB Serial support registered for Keyspan - (without
firmware)
<6>usbserial.c: USB Serial support registered for Keyspan 1 port adapter
<6>usbserial.c: USB Serial support registered for Keyspan 2 port adapter
<6>usbserial.c: USB Serial support registered for Keyspan 4 port adapter
<6>keyspan.c: v1.1.4:Keyspan USB to Serial Converter Driver
<6>usbserial.c: USB Serial support registered for ZyXEL - omni.net lcd
plus usb
<6>omninet.c: v1.1:USB ZyXEL omni.net LCD PLUS Driver
<6>usbserial.c: USB Serial support registered for Digi USB
<6>usbserial.c: USB Serial support registered for Digi USB
<6>digi_acceleport.c: v1.80.1.2:Digi AccelePort USB-2/USB-4 Serial
Converter driver
<6>usbserial.c: USB Serial support registered for Belkin / Peracom /
GoHubs USB Serial Adapter
<6>belkin_sa.c: USB Belkin Serial converter driver v1.2
<6>usbserial.c: USB Serial support registered for Empeg
<6>empeg.c: v1.2:USB Empeg Mark I/II Driver
<6>usbserial.c: USB Serial support registered for Magic Control
Technology USB-RS232
<6>mct_u232.c: Magic Control Technology USB-RS232 converter driver v1.1
<6>usbserial.c: USB Serial support registered for Edgeport 1 port
adapter
<6>usbserial.c: USB Serial support registered for Edgeport 2 port
adapter
<6>usbserial.c: USB Serial support registered for Edgeport 4 port
adapter
<6>usbserial.c: USB Serial support registered for Edgeport 8 port
adapter
<6>io_edgeport.c: Edgeport USB Serial Driver v2.3
<6>usbserial.c: USB Serial support registered for Edgeport TI 1 port
adapter
<6>usbserial.c: USB Serial support registered for Edgeport TI 2 port
adapter
<6>io_ti.c: Edgeport USB Serial Driver v0.2
<6>usbserial.c: USB Serial support registered for PL-2303
<6>pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.9
<6>usbserial.c: USB Serial support registered for Reiner SCT Cyberjack
USB card reader
<6>cyberjack.c: v1.0 Matthias Bruestle
<6>cyberjack.c: REINER SCT cyberJack pinpad/e-com USB Chipcard Reader
Driver
<6>usbserial.c: USB Serial support registered for IR Dongle
<6>ir-usb.c: USB IR Dongle driver v0.4
<6>usbserial.c: USB Serial support registered for KL5KUSB105D /
PalmConnect
<6>kl5kusb105.c: KLSI KL5KUSB105 chipset USB->Serial Converter driver
v0.3a
<6>usbserial.c: USB Serial support registered for KOBIL USB smart card
terminal
<6>kobil_sct.c: 12/03/2002 KOBIL Systems GmbH - http://www.kobil.com
<6>kobil_sct.c: KOBIL USB Smart Card Terminal Driver (experimental)
<6>Initializing USB Mass Storage driver...
<6>usb.c: registered new driver usb-storage
<6>USB Mass Storage support registered.
<6>mice: PS/2 mouse device common for all mice
<6>md: linear personality registered as nr 1
<6>md: raid0 personality registered as nr 2
<6>md: raid1 personality registered as nr 3
<6>md: raid5 personality registered as nr 4
<6>raid5: measuring checksumming speed
<4> 8regs : 2767.200 MB/sec
<4> 32regs : 1710.800 MB/sec
<4> pIII_sse : 3091.200 MB/sec
<4> pII_mmx : 2801.200 MB/sec
<4> p5_mmx : 2780.000 MB/sec
<4>raid5: using function: pIII_sse (3091.200 MB/sec)
<6>md: multipath personality registered as nr 7
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>LVM version 1.0.5+(22/07/2002)
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 8192 buckets, 128Kbytes
<6>TCP: Hash tables configured (established 131072 bind 43690)
<6>IPv4 over IPv4 tunneling driver
<6>GRE over IPv4 tunneling driver
<6>Linux IP multicast router 0.06 plus PIM-SM
<4>ip_conntrack version 2.1 (8192 buckets, 65536 max) - 292 bytes per
conntrack
<4>ip_tables: (C) 2000-2002 Netfilter core team
<6>ipt_recent v0.3.1: Stephen Frost <[email protected]>.
http://snowman.net/projects/ipt_recent/
<4>arp_tables: (C) 2002 David S. Miller
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<6>NET4: Linux IPX 0.47 for NET4.0
<6>IPX Portions Copyright (c) 1995 Caldera, Inc.
<6>IPX Portions Copyright (c) 2000, 2001 Conectiva, Inc.
<5>RAMDISK: Compressed image found at block 0
<6>Freeing initrd memory: 223k freed
<4>VFS: Mounted root (ext2 filesystem).
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>Freeing unused kernel memory: 392k freed
<6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,5), internal journal
<6>Adding Swap: 2040212k swap-space (priority -1)
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,0), internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>hdc: DMA disabled
<3>microcode: CPU0 no microcode found! (sig=f29, pflags=2)
<3>microcode: CPU1 no microcode found! (sig=f29, pflags=2)
<4>i2c-core.o: adapter Smbus i8254x at 03:0e.0 Int registered as adapter
0.
<4>i2c-core.o: adapter Smbus i8254x at 03:0e.0 Ext registered as adapter
1.
<4>Loading i8254x SMBus driver. Version 3.0.9
<6>e1000: eth0 NIC Link is Up 100 Mbps Full Duplex
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<7>usbserial.c: serial_open
<4>calling pci_register_driver
<4>entering piraqProbe
<4>current number of piraqs: 0
<4>before pci_enable_device
<4>Piraq 1 located at bus 6, device/function 0x20
<4> pci configuration space:
<4>
<4> 0x00: e8 10 20 59 03 01 80 02 00 00 00 09 00 00 00 00
<4> 0x10: 81 dc 00 00 00 00 ae fd 00 fc ad fd 00 f8 ad fd
<4> 0x20: 00 00 a0 fd 00 00 00 00 00 00 00 00 00 00 00 00
<4> 0x30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
<4> silicon version 0
<4> interrupt line 9
<4> interrupt pin 1
<4> irq 93
<4> Base address[0]: I/O 0x0000dc80 0x00000080 128
<4> Base address[1]: MEM 0xfdae0000 0x00020000 131072
<4> Base address[2]: MEM 0xfdadfc00 0x00000040 64
<4> Base address[3]: MEM 0xfdadf800 0x00000010 16
<4> Base address[4]: MEM 0xfda00000 0x00080000 524288
<4> Base address[5]: 0x00000000 0x00000000 0
<4>piraq count now at 1
<4>entering piraqProbe
<4>current number of piraqs: 1
<4>before pci_enable_device
<4>Piraq 2 located at bus 6, device/function 0x30
<4> pci configuration space:
<4>
<4> 0x00: e8 10 20 59 03 01 80 02 00 00 00 09 00 00 00 00
<4> 0x10: 01 dc 00 00 00 00 aa fd 00 f4 ad fd 00 f0 ad fd
<4> 0x20: 00 00 98 fd 00 00 00 00 00 00 00 00 00 00 00 00
<4> 0x30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
<4> silicon version 0
<4> interrupt line 9
<4> interrupt pin 1
<4> irq 95
<4> Base address[0]: I/O 0x0000dc00 0x00000080 128
<4> Base address[1]: MEM 0xfdaa0000 0x00020000 131072
<4> Base address[2]: MEM 0xfdadf400 0x00000040 64
<4> Base address[3]: MEM 0xfdadf000 0x00000010 16
<4> Base address[4]: MEM 0xfd980000 0x00080000 524288
<4> Base address[5]: 0x00000000 0x00000000 0
<4>piraq count now at 2
<4>entering piraqProbe
<4>current number of piraqs: 2
<4>before pci_enable_device
<4>Piraq 3 located at bus 6, device/function 0x38
<4> pci configuration space:
<4>
<4> 0x00: e8 10 20 59 03 01 80 02 00 00 00 09 00 00 00 00
<4> 0x10: 81 d8 00 00 00 00 a8 fd 00 ec ad fd 00 e8 ad fd
<4> 0x20: 00 00 90 fd 00 00 00 00 00 00 00 00 00 00 00 00
<4> 0x30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
<4> silicon version 0
<4> interrupt line 9
<4> interrupt pin 1
<4> irq 92
<4> Base address[0]: I/O 0x0000d880 0x00000080 128
<4> Base address[1]: MEM 0xfda80000 0x00020000 131072
<4> Base address[2]: MEM 0xfdadec00 0x00000040 64
<4> Base address[3]: MEM 0xfdade800 0x00000010 16
<4> Base address[4]: MEM 0xfd900000 0x00080000 524288
<4> Base address[5]: 0x00000000 0x00000000 0
<4>piraq count now at 3
<4>entering piraqProbe
<4>current number of piraqs: 3
<4>before pci_enable_device
<4>Piraq 4 located at bus 6, device/function 0x48
<4> pci configuration space:
<4>
<4> 0x00: e8 10 20 59 03 01 80 02 00 00 00 09 00 00 00 00
<4> 0x10: 01 d8 00 00 00 00 8e fd 00 e4 ad fd 00 e0 ad fd
<4> 0x20: 00 00 80 fd 00 00 00 00 00 00 00 00 00 00 00 00
<4> 0x30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
<4> silicon version 0
<4> interrupt line 9
<4> interrupt pin 1
<4> irq 94
<4> Base address[0]: I/O 0x0000d800 0x00000080 128
<4> Base address[1]: MEM 0xfd8e0000 0x00020000 131072
<4> Base address[2]: MEM 0xfdade400 0x00000040 64
<4> Base address[3]: MEM 0xfdade000 0x00000010 16
<4> Base address[4]: MEM 0xfd800000 0x00080000 524288
<4> Base address[5]: 0x00000000 0x00000000 0
<4>piraq count now at 4
<4>after pci_register_driver
<4>initializing state for board 0, dsp 0
<4>initializing state for board 0, dsp 1
<4>initializing state for board 1, dsp 0
<4>initializing state for board 1, dsp 1
<4>initializing state for board 2, dsp 0
<4>initializing state for board 2, dsp 1
<4>initializing state for board 3, dsp 0
<4>initializing state for board 3, dsp 1
<4>allocating memory for piraq 0, dsp 0
<4>allocating memory for piraq 0, dsp 1
<4>allocating memory for piraq 1, dsp 0
<4>allocating memory for piraq 1, dsp 1
<4>allocating memory for piraq 2, dsp 0
<4>allocating memory for piraq 2, dsp 1
<4>allocating memory for piraq 3, dsp 0
<4>allocating memory for piraq 3, dsp 1
<4>piraq debugging at after allocateMemory
<4>calling piraqPciSetup
<4>piraq debugging at entering piraqPciSetup
<4>piraq debugging at --------------------------------------------
<4>piraq debugging at getting pci resources for next piraq
<4>piraq debugging at remapping memory areas
<4> wave remapped from 0xfda00000 to 0xfad21000
<4> dsp dpr remapped from 0xfdae0000 to 0xfada2000
<4> dsp0 pDprComm is 0xfada2100
<4> dsp0 intPending is 0xfada2100
<4> dsp1 pDprComm is 0xfadb2100
<4> dsp1 intPending is 0xfadb2100
<4> status remapped to 0xfad1f800
<4> counter remapped to 0xfadc3c00
<4> addint clear is 0xfadc3c20
<4> mailbox size(words) 0x00002805
<4> free dpr begins at 0x00002845
<4> free dpr len(words) 0x000017bb
<4>piraq debugging at calling piraq_boardReset
<4>dsp 0a counters set to zero
<4>dsp 0b counters set to zero
<4>piraq debugging at after piraq_boardReset
<4>piraq debugging at --------------------------------------------
<4>piraq debugging at getting pci resources for next piraq
<4>piraq debugging at remapping memory areas
<4> wave remapped from 0xfd980000 to 0xfadc7000
<4> dsp dpr remapped from 0xfdaa0000 to 0xfae48000
<4> dsp0 pDprComm is 0xfae48100
<4> dsp0 intPending is 0xfae48100
<4> dsp1 pDprComm is 0xfae58100
<4> dsp1 intPending is 0xfae58100
<4> status remapped to 0xfadc5000
<4> counter remapped to 0xfae69400
<4> addint clear is 0xfae69420
<4> mailbox size(words) 0x00002805
<4> free dpr begins at 0x00002845
<4> free dpr len(words) 0x000017bb
<4>piraq debugging at calling piraq_boardReset
<4>dsp 1a counters set to zero
<4>dsp 1b counters set to zero
<4>piraq debugging at after piraq_boardReset
<4>piraq debugging at --------------------------------------------
<4>piraq debugging at getting pci resources for next piraq
<4>piraq debugging at remapping memory areas
<4> wave remapped from 0xfd900000 to 0xfae6d000
<4> dsp dpr remapped from 0xfda80000 to 0xfaeee000
<4> dsp0 pDprComm is 0xfaeee100
<4> dsp0 intPending is 0xfaeee100
<4> dsp1 pDprComm is 0xfaefe100
<4> dsp1 intPending is 0xfaefe100
<4> status remapped to 0xfae6b800
<4> counter remapped to 0xfaf0fc00
<4> addint clear is 0xfaf0fc20
<4> mailbox size(words) 0x00002805
<4> free dpr begins at 0x00002845
<4> free dpr len(words) 0x000017bb
<4>piraq debugging at calling piraq_boardReset
<4>dsp 2a counters set to zero
<4>dsp 2b counters set to zero
<4>piraq debugging at after piraq_boardReset
<4>piraq debugging at --------------------------------------------
<4>piraq debugging at getting pci resources for next piraq
<4>piraq debugging at remapping memory areas
<4> wave remapped from 0xfd800000 to 0xfaf13000
<4> dsp dpr remapped from 0xfd8e0000 to 0xfaf94000
<4> dsp0 pDprComm is 0xfaf94100
<4> dsp0 intPending is 0xfaf94100
<4> dsp1 pDprComm is 0xfafa4100
<4> dsp1 intPending is 0xfafa4100
<4> status remapped to 0xfaf11000
<4> counter remapped to 0xfafb5400
<4> addint clear is 0xfafb5420
<4> mailbox size(words) 0x00002805
<4> free dpr begins at 0x00002845
<4> free dpr len(words) 0x000017bb
<4>piraq debugging at calling piraq_boardReset
<4>dsp 3a counters set to zero
<4>dsp 3b counters set to zero
<4>piraq debugging at after piraq_boardReset
<4>piraq debugging at leaving pciSetup
<4>piraq debugging at after piraqPciSetup
<4>piraq debugging at requesting interrupt
<4> irq 93 registered for piraq #0
<4> irq 95 registered for piraq #1
<4> irq 92 registered for piraq #2
<4> irq 94 registered for piraq #3
<4>piraq debugging at calling register_chrdev for piraq
<4>piraq debugging at calling register_chrdev for dsp
<4>piraq debugging at calling procfs_init
<4>piraq registration succesful for 4 cards
On Mon, 3 Nov 2003, Charles Martin wrote:
>
> I enabled APIC_DEBUG, and here is the dmesg output.
Hmm..
The MP tables mention IRQ's up to 51, but no further.
But the PIRQ routing tables talk about irqs 92-95 for bus 6.
It really looks like the IRQ routing entries are just broken. One
potential fix is to enable ACPI, and hope that the ACPI irq routing isn't
as broken as the PIRQ stuff.
Other than that I don't see anything we can do. Anybody else?
Linus
> -----Original Message-----
> From: Linus Torvalds [mailto:[email protected]]
> Sent: Monday, November 03, 2003 1:23 PM
> To: Charles Martin
> Cc: [email protected]; [email protected]
> Subject: RE: interrupts across PCI bridge(s) not handled
>
>
>
> On Mon, 3 Nov 2003, Charles Martin wrote:
> >
> > I enabled APIC_DEBUG, and here is the dmesg output.
>
> Hmm..
>
> The MP tables mention IRQ's up to 51, but no further.
>
> But the PIRQ routing tables talk about irqs 92-95 for bus 6.
>
> It really looks like the IRQ routing entries are just broken. One
> potential fix is to enable ACPI, and hope that the ACPI irq
> routing isn't
> as broken as the PIRQ stuff.
>
> Other than that I don't see anything we can do. Anybody else?
>
> Linus
>
>
I do notice that bus #6, which is the backplane extender,
has an APIC id of 0, but an APIC #0 was not enumerated. All other
buses get assigned to the identified APICs of 8, 9 and 10.
Charlie
On Mon, 3 Nov 2003, Charles Martin wrote:
>
> I do notice that bus #6, which is the backplane extender,
> has an APIC id of 0, but an APIC #0 was not enumerated. All other
> buses get assigned to the identified APICs of 8, 9 and 10.
Yes. However, I have this suspicion that that is just more confusion by
the BIOS tables.
The reason APIC #0 wasn't enumerated is that it doesn't seem to exist in
the MP tables. So not only does the PIRQ table not contain any information
about that bus, but the MP tables are very silent about it too.
I dunno.. Maybe I'm reading this wrong, but it really looks like your BIOS
tables are just pretty broken.
It would really be interesting to hear whether using ACPI enumeration
fixes it or at least whether the symptoms are different. Especially with
newer hardware, the BIOS people have only ever tested their tables with
Windows, and ACPI will have overridden any MPtable information, so..
Linus
>
> Hmm..
>
> The MP tables mention IRQ's up to 51, but no further.
>
> But the PIRQ routing tables talk about irqs 92-95 for bus 6.
>
> It really looks like the IRQ routing entries are just broken. One
> potential fix is to enable ACPI, and hope that the ACPI irq
> routing isn't
> as broken as the PIRQ stuff.
>
> Other than that I don't see anything we can do. Anybody else?
>
> Linus
>
I enabled ACPI, and the interrupts are now assigned correctly,
and in the range of 48-51:
CPU0 CPU1
48: 878 389 IO-APIC-level piraq
49: 923 336 IO-APIC-level piraq
50: 17239 838 IO-APIC-level ioc2, piraq
51: 879 404 IO-APIC-level piraq
They are now getting handled properly, i.e. I am receiveing
interrupts from the boards located in the backplane extender.
This is with 2.4.22.
I didn't realize that ACPI is related to interrupt management
as well as power control. Is there any downside to using ACPI?
Thanks,
Charlie
On Mon, 3 Nov 2003, Charles Martin wrote:
>
> I enabled ACPI, and the interrupts are now assigned correctly,
> and in the range of 48-51:
Good.
> I didn't realize that ACPI is related to interrupt management
> as well as power control. Is there any downside to using ACPI?
The downside to ACPI is that it's a complex standard, and with complexity
comes the inevitable bugs. As you just found out, it does a lot more than
just power control (the "C" is for "Configuration").
On some machines the ACPI support is even more broken than other BIOS
tables, but it's getting better.
Linus
On Mon, 3 Nov 2003, Linus Torvalds wrote:
>
> On Mon, 3 Nov 2003, Charles Martin wrote:
> >
> > I have a pci backplane extender, with 4 cards
> > (named piraq) in it. The cards are detected by
> > the PCI system, and irqs 92-95 are assigned,
> > as shown in /var/log/messages:
> >
> > kernel: PCI->APIC IRQ transform: (B6,I4,P0) -> 93
> > kernel: PCI->APIC IRQ transform: (B6,I6,P0) -> 95
> > kernel: PCI->APIC IRQ transform: (B6,I7,P0) -> 92
> > kernel: PCI->APIC IRQ transform: (B6,I9,P0) -> 94
>
> Can you enable APIC_DEBUG debugging in "include/asm-i386/apic.h", and make
> sure that you build the kernel with a big printk buffer. Then, in case
> your distribution comes with a broken "dmesg" binary that doesn't show
> more than about 20kB of data, compile this trivial program and run it
> after bootup, and send the whole log out..
>
> It would be a pity to have to boot with "noapic", since this is exactly
> the kind of situation where you _want_ the extra interrupts.
I wonder how the request_irq worked there, doesn't 'none' denote no
irq_desc[i].handler == no_irq_type?
>>>>> "Charles" == Charles Martin <[email protected]> writes:
Charles> They are now getting handled properly, i.e. I am receiveing
Charles> interrupts from the boards located in the backplane extender.
Charles> This is with 2.4.22.
Charles> I didn't realize that ACPI is related to interrupt management
Charles> as well as power control. Is there any downside to using
Charles> ACPI?
Yep it does ;-( IA64 relies exclusively on ACPI for irq routing and on
x86 you are seeing more and more hardware that requires it as well,
notably Sony laptops such as the R505 series will not see interrupts
assigned to their cardbus bridge without ACPI interrupt routing.
As for downsides, take a look at the ACPI spec and judge for
yourself. I'll refrain from commenting ;-)
Cheers,
Jes
On Mon, 3 Nov 2003, Linux Torvalds wrote:
> On Mon, 3 Nov 2003, Charles Martin wrote:
> >
> > I enabled ACPI, and the interrupts are now assigned correctly,
> > and in the range of 48-51:
>
> Good.
>
> > I didn't realize that ACPI is related to interrupt management
> > as well as power control. Is there any downside to using ACPI?
>
> The downside to ACPI is that it's a complex standard, and with
> complexity
> comes the inevitable bugs. As you just found out, it does a lot more
> than
> just power control (the "C" is for "Configuration").
>
> On some machines the ACPI support is even more broken than other BIOS
> tables, but it's getting better.
I infer from this discussion that the old (2.2.x-era) rule-of-thumb
about disabling ACPI for SMP systems is now dangerous advice. True?
(Even for a 2.4.x series kernel?) Any other "gotchas" with ACPI and SMP
systems?
Frank Horowitz