Initial introduction of Facebook Bletchley equipped with
Aspeed 2600 BMC SoC.
Signed-off-by: Howard Chiu <[email protected]>
---
Change since v7:
- Add switchphy mode back due to unknown failure
Change since v6:
- Fix FUSB302 node warnings
- Remove switchphy node.
- Remvoe status property from spi-gpio node
- Remove interrupt pin of FUSB302 temporally due to hardware issue
- Add more gpio-line-name
- Replace MP5023 device drivr with "mps,mp5023"
Change since v5:
- Add an EEPROM on i2c-7
- Change address of FUSB302 to 0x22
- Assign interrupt pin to FUSB302
- Rework pin assignment of pca9539
Change since v4:
- Change address of TMP421 on i2c-12 to 0x4d
Change since v3:
- Add a TMP421 on i2c-10
Change since v2:
- Remove uart5 workaround
- Remove gpio nodes of pca9552/pca9539
- Modify gpio-line-name of led/power/presence pins with openbmc pattern
- Add MP5023 devices
Change since v1:
- Keep sorted in Makefile
- Change baudrate to 57600 from 115200
- Rename node *-ember to *-amber
- Use openbmc-flash-layout-128.dtsi
arch/arm/boot/dts/Makefile | 1 +
.../dts/aspeed-bmc-facebook-bletchley.dts | 756 ++++++++++++++++++
2 files changed, 757 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..b804b577010a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1482,6 +1482,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-arm-stardragon4800-rep2.dtb \
aspeed-bmc-asrock-e3c246d4i.dtb \
aspeed-bmc-bytedance-g220a.dtb \
+ aspeed-bmc-facebook-bletchley.dtb \
aspeed-bmc-facebook-cloudripper.dtb \
aspeed-bmc-facebook-cmm.dtb \
aspeed-bmc-facebook-elbert.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
new file mode 100644
index 000000000000..f973ea883b97
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -0,0 +1,756 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/usb/pd.h>
+
+/ {
+ model = "Facebook Bletchley BMC";
+ compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial4 = &uart5;
+ };
+
+ chosen {
+ bootargs = "console=ttyS4,57600n8";
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+ <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+ <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+ <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+ };
+
+ spi_gpio: spi-gpio {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+
+ tpmdev@0 {
+ compatible = "tcg,tpm_tis-spi";
+ spi-max-frequency = <33000000>;
+ reg = <0>;
+ };
+ };
+
+ switchphy: ethernet-phy@0 {
+ // Fixed link
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ sys_log_id {
+ retain-state-shutdown;
+ default-state = "keep";
+ gpios = <&front_leds 0 GPIO_ACTIVE_HIGH>;
+ };
+ fan0_blue {
+ retain-state-shutdown;
+ default-state = "on";
+ gpios = <&fan_ioexp 8 GPIO_ACTIVE_HIGH>;
+ };
+ fan1_blue {
+ retain-state-shutdown;
+ default-state = "on";
+ gpios = <&fan_ioexp 9 GPIO_ACTIVE_HIGH>;
+ };
+ fan2_blue {
+ retain-state-shutdown;
+ default-state = "on";
+ gpios = <&fan_ioexp 10 GPIO_ACTIVE_HIGH>;
+ };
+ fan3_blue {
+ retain-state-shutdown;
+ default-state = "on";
+ gpios = <&fan_ioexp 11 GPIO_ACTIVE_HIGH>;
+ };
+ fan0_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&fan_ioexp 12 GPIO_ACTIVE_HIGH>;
+ };
+ fan1_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&fan_ioexp 13 GPIO_ACTIVE_HIGH>;
+ };
+ fan2_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&fan_ioexp 14 GPIO_ACTIVE_HIGH>;
+ };
+ fan3_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&fan_ioexp 15 GPIO_ACTIVE_HIGH>;
+ };
+ sled0_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled0_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled0_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled0_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled1_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled1_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled2_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled2_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled3_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled3_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled4_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled4_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ sled5_amber {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
+ };
+ sled5_blue {
+ retain-state-shutdown;
+ default-state = "off";
+ gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&mac2 {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&switchphy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii3_default>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+ };
+};
+
+&spi2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi2_default>;
+
+ flash@0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "pnor";
+ spi-max-frequency = <100000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled0_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED0_MS_DETECT1","SLED0_VBUS_BMC_EN","SLED0_INA230_ALERT","SLED0_P12V_STBY_ALERT",
+ "SLED0_SSD_ALERT","SLED0_MS_DETECT0","SLED0_RST_CCG5","SLED0_FUSB302_INT",
+ "SLED0_MD_STBY_RESET","SLED0_MD_IOEXP_EN_FAULT","SLED0_MD_DIR","SLED0_MD_DECAY",
+ "SLED0_MD_MODE1","SLED0_MD_MODE2","SLED0_MD_MODE3","power-host0";
+ };
+
+ sled0_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled0-amber","led-sled0-blue","SLED0_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled0_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled1_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
+ "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
+ "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
+ "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
+ };
+
+ sled1_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled1_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled2_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
+ "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
+ "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
+ "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
+ };
+
+ sled2_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled2_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled3_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
+ "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
+ "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
+ "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
+ };
+
+ sled3_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled3_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c4 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled4_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
+ "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
+ "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
+ "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
+ };
+
+ sled4_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled4_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+ /* TODO: Add ADC INA230 */
+
+ mp5023@40 {
+ compatible = "mps,mp5023";
+ reg = <0x40>;
+ };
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ sled5_ioexp: pca9539@76 {
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
+ "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
+ "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
+ "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
+ };
+
+ sled5_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+
+ sled5_fusb302: typec-portc@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ try-power-role = "sink";
+ data-role = "dual";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(3000, 12000, 3000)
+ PDO_PPS_APDO(3000, 11000, 3000)>;
+ op-sink-microwatt = <10000000>;
+ };
+ };
+};
+
+&i2c6 {
+ status = "okay";
+
+ eeprom@56 {
+ compatible = "atmel,24c64";
+ reg = <0x56>;
+ };
+
+ rtc@51 {
+ compatible = "nxp,pcf85263";
+ reg = <0x51>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ eeprom@54 {
+ compatible = "atmel,24c64";
+ reg = <0x54>;
+ };
+};
+
+&i2c9 {
+ status = "okay";
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+};
+
+&i2c10 {
+ status = "okay";
+
+ tmp421@4f {
+ compatible = "ti,tmp421";
+ reg = <0x4f>;
+ };
+
+ hdc1080@40 {
+ compatible = "ti,hdc1080";
+ reg = <0x40>;
+ };
+
+ front_leds: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "led-fault-identify","power-p5v-stby-good",
+ "power-p1v0-dvdd-good","power-p1v0-avdd-good",
+ "","","","",
+ "","","","",
+ "","","","";
+ };
+};
+
+&i2c12 {
+ status = "okay";
+
+ adm1278@11 {
+ compatible = "adi,adm1278";
+ reg = <0x11>;
+ };
+
+ tmp421@4c {
+ compatible = "ti,tmp421";
+ reg = <0x4c>;
+ };
+
+ tmp421@4d {
+ compatible = "ti,tmp421";
+ reg = <0x4d>;
+ };
+
+ fan_ioexp: pca9552@67 {
+ compatible = "nxp,pca9552";
+ reg = <0x67>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio-line-names =
+ "presence-fan0","presence-fan1",
+ "presence-fan2","presence-fan3",
+ "power-fan0-good","power-fan1-good",
+ "power-fan2-good","power-fan3-good",
+ "","","","",
+ "","","","";
+ };
+};
+
+&i2c13 {
+ multi-master;
+ aspeed,hw-timeout-ms = <1000>;
+ status = "okay";
+};
+
+&gpio0 {
+ gpio-line-names =
+ /*A0-A7*/ "","","","","","","","",
+ /*B0-B7*/ "","","SEL_SPI2_MUX","SPI2_MUX1",
+ "SPI2_MUX2","SPI2_MUX3","","",
+ /*C0-C7*/ "","","","","","","","",
+ /*D0-D7*/ "","","","","","","","",
+ /*E0-E7*/ "","","","","","","","",
+ /*F0-F7*/ "","","","","","","","",
+ /*G0-G7*/ "","SWITCH_FRU_MUX","","","","","","",
+ /*H0-H7*/ "presence-riser1","presence-riser2",
+ "presence-sled0","presence-sled1",
+ "presence-sled2","presence-sled3",
+ "presence-sled4","presence-sled5",
+ /*I0-I7*/ "REV_ID0","","REV_ID1","REV_ID2",
+ "","","","",
+ /*J0-J7*/ "","","","","","","","",
+ /*K0-K7*/ "","","","","","","","",
+ /*L0-L7*/ "","","","","","","","",
+ /*M0-M7*/ "ALERT_SLED0","ALERT_SLED1",
+ "ALERT_SLED2","ALERT_SLED3",
+ "ALERT_SLED4","ALERT_SLED5",
+ "P12V_AUX_ALERT1","",
+ /*N0-N7*/ "","","","","","","","",
+ /*O0-O7*/ "","","","",
+ "","BOARD_ID0","BOARD_ID1","BOARD_ID2",
+ /*P0-P7*/ "","","","","","","","",
+ /*Q0-Q7*/ "","","","","","","","",
+ /*R0-R7*/ "","","","","","","","",
+ /*S0-S7*/ "","","","BAT_DETECT",
+ "BMC_BT_WP0","BMC_BT_WP1","","",
+ /*T0-T7*/ "","","","","","","","",
+ /*U0-U7*/ "","","","","","","","",
+ /*V0-V7*/ "","RST_BMC_MVL","","",
+ "USB2_SEL0_A","USB2_SEL1_A",
+ "USB2_SEL0_B","USB2_SEL1_B",
+ /*W0-W7*/ "RST_FRONT_IOEXP","","","","","","","",
+ /*X0-X7*/ "","","","","","","","",
+ /*Y0-Y7*/ "","","BSM_FLASH_LATCH","","","","","",
+ /*Z0-Z7*/ "","","","","","","","";
+};
+
+&adc0 {
+ vref = <1800>;
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+ &pinctrl_adc2_default &pinctrl_adc3_default
+ &pinctrl_adc4_default &pinctrl_adc5_default
+ &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+ vref = <2500>;
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+ &pinctrl_adc10_default &pinctrl_adc11_default
+ &pinctrl_adc12_default &pinctrl_adc13_default
+ &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
--
2.25.1
Hi Patrick,
On Tue, 7 Dec 2021 at 09:52, Howard Chiu <[email protected]> wrote:
>
> Initial introduction of Facebook Bletchley equipped with
> Aspeed 2600 BMC SoC.
>
> Signed-off-by: Howard Chiu <[email protected]>
Are you ok for this one to go in for v5.17?
> ---
> Change since v7:
> - Add switchphy mode back due to unknown failure
>
> Change since v6:
> - Fix FUSB302 node warnings
> - Remove switchphy node.
> - Remvoe status property from spi-gpio node
> - Remove interrupt pin of FUSB302 temporally due to hardware issue
> - Add more gpio-line-name
> - Replace MP5023 device drivr with "mps,mp5023"
>
> Change since v5:
> - Add an EEPROM on i2c-7
> - Change address of FUSB302 to 0x22
> - Assign interrupt pin to FUSB302
> - Rework pin assignment of pca9539
>
> Change since v4:
> - Change address of TMP421 on i2c-12 to 0x4d
>
> Change since v3:
> - Add a TMP421 on i2c-10
>
> Change since v2:
> - Remove uart5 workaround
> - Remove gpio nodes of pca9552/pca9539
> - Modify gpio-line-name of led/power/presence pins with openbmc pattern
> - Add MP5023 devices
>
> Change since v1:
> - Keep sorted in Makefile
> - Change baudrate to 57600 from 115200
> - Rename node *-ember to *-amber
> - Use openbmc-flash-layout-128.dtsi
>
> arch/arm/boot/dts/Makefile | 1 +
> .../dts/aspeed-bmc-facebook-bletchley.dts | 756 ++++++++++++++++++
> 2 files changed, 757 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 0de64f237cd8..b804b577010a 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1482,6 +1482,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-arm-stardragon4800-rep2.dtb \
> aspeed-bmc-asrock-e3c246d4i.dtb \
> aspeed-bmc-bytedance-g220a.dtb \
> + aspeed-bmc-facebook-bletchley.dtb \
> aspeed-bmc-facebook-cloudripper.dtb \
> aspeed-bmc-facebook-cmm.dtb \
> aspeed-bmc-facebook-elbert.dtb \
> diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
> new file mode 100644
> index 000000000000..f973ea883b97
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
> @@ -0,0 +1,756 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +// Copyright (c) 2021 Facebook Inc.
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/usb/pd.h>
> +
> +/ {
> + model = "Facebook Bletchley BMC";
> + compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
> +
> + aliases {
> + serial4 = &uart5;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS4,57600n8";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x80000000>;
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
> + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
> + <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
> + <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
> + };
> +
> + spi_gpio: spi-gpio {
> + compatible = "spi-gpio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
> + gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
> + gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
> + num-chipselects = <1>;
> + cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
> +
> + tpmdev@0 {
> + compatible = "tcg,tpm_tis-spi";
> + spi-max-frequency = <33000000>;
> + reg = <0>;
> + };
> + };
> +
> + switchphy: ethernet-phy@0 {
> + // Fixed link
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + sys_log_id {
> + retain-state-shutdown;
> + default-state = "keep";
> + gpios = <&front_leds 0 GPIO_ACTIVE_HIGH>;
> + };
> + fan0_blue {
> + retain-state-shutdown;
> + default-state = "on";
> + gpios = <&fan_ioexp 8 GPIO_ACTIVE_HIGH>;
> + };
> + fan1_blue {
> + retain-state-shutdown;
> + default-state = "on";
> + gpios = <&fan_ioexp 9 GPIO_ACTIVE_HIGH>;
> + };
> + fan2_blue {
> + retain-state-shutdown;
> + default-state = "on";
> + gpios = <&fan_ioexp 10 GPIO_ACTIVE_HIGH>;
> + };
> + fan3_blue {
> + retain-state-shutdown;
> + default-state = "on";
> + gpios = <&fan_ioexp 11 GPIO_ACTIVE_HIGH>;
> + };
> + fan0_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&fan_ioexp 12 GPIO_ACTIVE_HIGH>;
> + };
> + fan1_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&fan_ioexp 13 GPIO_ACTIVE_HIGH>;
> + };
> + fan2_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&fan_ioexp 14 GPIO_ACTIVE_HIGH>;
> + };
> + fan3_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&fan_ioexp 15 GPIO_ACTIVE_HIGH>;
> + };
> + sled0_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled0_leds 0 GPIO_ACTIVE_LOW>;
> + };
> + sled0_blue {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled0_leds 1 GPIO_ACTIVE_LOW>;
> + };
> + sled1_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
> + };
> + sled1_blue {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
> + };
> + sled2_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
> + };
> + sled2_blue {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
> + };
> + sled3_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
> + };
> + sled3_blue {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
> + };
> + sled4_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
> + };
> + sled4_blue {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
> + };
> + sled5_amber {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
> + };
> + sled5_blue {
> + retain-state-shutdown;
> + default-state = "off";
> + gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&mac2 {
> + status = "okay";
> + phy-mode = "rgmii";
> + phy-handle = <&switchphy>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii3_default>;
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&fmc {
> + status = "okay";
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout-128.dtsi"
> + };
> +};
> +
> +&spi2 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi2_default>;
> +
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "pnor";
> + spi-max-frequency = <100000000>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> + /* TODO: Add ADC INA230 */
> +
> + mp5023@40 {
> + compatible = "mps,mp5023";
> + reg = <0x40>;
> + };
> +
> + tmp421@4f {
> + compatible = "ti,tmp421";
> + reg = <0x4f>;
> + };
> +
> + sled0_ioexp: pca9539@76 {
> + compatible = "nxp,pca9539";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "SLED0_MS_DETECT1","SLED0_VBUS_BMC_EN","SLED0_INA230_ALERT","SLED0_P12V_STBY_ALERT",
> + "SLED0_SSD_ALERT","SLED0_MS_DETECT0","SLED0_RST_CCG5","SLED0_FUSB302_INT",
> + "SLED0_MD_STBY_RESET","SLED0_MD_IOEXP_EN_FAULT","SLED0_MD_DIR","SLED0_MD_DECAY",
> + "SLED0_MD_MODE1","SLED0_MD_MODE2","SLED0_MD_MODE3","power-host0";
> + };
> +
> + sled0_leds: pca9552@67 {
> + compatible = "nxp,pca9552";
> + reg = <0x67>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "led-sled0-amber","led-sled0-blue","SLED0_RST_IOEXP","",
> + "","","","",
> + "","","","",
> + "","","","";
> + };
> +
> + sled0_fusb302: typec-portc@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "dual";
> + try-power-role = "sink";
> + data-role = "dual";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> + PDO_VAR(3000, 12000, 3000)
> + PDO_PPS_APDO(3000, 11000, 3000)>;
> + op-sink-microwatt = <10000000>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> + /* TODO: Add ADC INA230 */
> +
> + mp5023@40 {
> + compatible = "mps,mp5023";
> + reg = <0x40>;
> + };
> +
> + tmp421@4f {
> + compatible = "ti,tmp421";
> + reg = <0x4f>;
> + };
> +
> + sled1_ioexp: pca9539@76 {
> + compatible = "nxp,pca9539";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
> + "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
> + "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
> + "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
> + };
> +
> + sled1_leds: pca9552@67 {
> + compatible = "nxp,pca9552";
> + reg = <0x67>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","",
> + "","","","",
> + "","","","",
> + "","","","";
> + };
> +
> + sled1_fusb302: typec-portc@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "dual";
> + try-power-role = "sink";
> + data-role = "dual";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> + PDO_VAR(3000, 12000, 3000)
> + PDO_PPS_APDO(3000, 11000, 3000)>;
> + op-sink-microwatt = <10000000>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + status = "okay";
> + /* TODO: Add ADC INA230 */
> +
> + mp5023@40 {
> + compatible = "mps,mp5023";
> + reg = <0x40>;
> + };
> +
> + tmp421@4f {
> + compatible = "ti,tmp421";
> + reg = <0x4f>;
> + };
> +
> + sled2_ioexp: pca9539@76 {
> + compatible = "nxp,pca9539";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
> + "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
> + "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
> + "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
> + };
> +
> + sled2_leds: pca9552@67 {
> + compatible = "nxp,pca9552";
> + reg = <0x67>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","",
> + "","","","",
> + "","","","",
> + "","","","";
> + };
> +
> + sled2_fusb302: typec-portc@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "dual";
> + try-power-role = "sink";
> + data-role = "dual";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> + PDO_VAR(3000, 12000, 3000)
> + PDO_PPS_APDO(3000, 11000, 3000)>;
> + op-sink-microwatt = <10000000>;
> + };
> + };
> +};
> +
> +&i2c3 {
> + status = "okay";
> + /* TODO: Add ADC INA230 */
> +
> + mp5023@40 {
> + compatible = "mps,mp5023";
> + reg = <0x40>;
> + };
> +
> + tmp421@4f {
> + compatible = "ti,tmp421";
> + reg = <0x4f>;
> + };
> +
> + sled3_ioexp: pca9539@76 {
> + compatible = "nxp,pca9539";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
> + "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
> + "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
> + "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
> + };
> +
> + sled3_leds: pca9552@67 {
> + compatible = "nxp,pca9552";
> + reg = <0x67>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","",
> + "","","","",
> + "","","","",
> + "","","","";
> + };
> +
> + sled3_fusb302: typec-portc@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "dual";
> + try-power-role = "sink";
> + data-role = "dual";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> + PDO_VAR(3000, 12000, 3000)
> + PDO_PPS_APDO(3000, 11000, 3000)>;
> + op-sink-microwatt = <10000000>;
> + };
> + };
> +};
> +
> +&i2c4 {
> + status = "okay";
> + /* TODO: Add ADC INA230 */
> +
> + mp5023@40 {
> + compatible = "mps,mp5023";
> + reg = <0x40>;
> + };
> +
> + tmp421@4f {
> + compatible = "ti,tmp421";
> + reg = <0x4f>;
> + };
> +
> + sled4_ioexp: pca9539@76 {
> + compatible = "nxp,pca9539";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
> + "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
> + "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
> + "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
> + };
> +
> + sled4_leds: pca9552@67 {
> + compatible = "nxp,pca9552";
> + reg = <0x67>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","",
> + "","","","",
> + "","","","",
> + "","","","";
> + };
> +
> + sled4_fusb302: typec-portc@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "dual";
> + try-power-role = "sink";
> + data-role = "dual";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> + PDO_VAR(3000, 12000, 3000)
> + PDO_PPS_APDO(3000, 11000, 3000)>;
> + op-sink-microwatt = <10000000>;
> + };
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> + /* TODO: Add ADC INA230 */
> +
> + mp5023@40 {
> + compatible = "mps,mp5023";
> + reg = <0x40>;
> + };
> +
> + tmp421@4f {
> + compatible = "ti,tmp421";
> + reg = <0x4f>;
> + };
> +
> + sled5_ioexp: pca9539@76 {
> + compatible = "nxp,pca9539";
> + reg = <0x76>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
> + "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
> + "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
> + "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
> + };
> +
> + sled5_leds: pca9552@67 {
> + compatible = "nxp,pca9552";
> + reg = <0x67>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","",
> + "","","","",
> + "","","","",
> + "","","","";
> + };
> +
> + sled5_fusb302: typec-portc@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "dual";
> + try-power-role = "sink";
> + data-role = "dual";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> + PDO_VAR(3000, 12000, 3000)
> + PDO_PPS_APDO(3000, 11000, 3000)>;
> + op-sink-microwatt = <10000000>;
> + };
> + };
> +};
> +
> +&i2c6 {
> + status = "okay";
> +
> + eeprom@56 {
> + compatible = "atmel,24c64";
> + reg = <0x56>;
> + };
> +
> + rtc@51 {
> + compatible = "nxp,pcf85263";
> + reg = <0x51>;
> + };
> +};
> +
> +&i2c7 {
> + status = "okay";
> +
> + eeprom@54 {
> + compatible = "atmel,24c64";
> + reg = <0x54>;
> + };
> +};
> +
> +&i2c9 {
> + status = "okay";
> +
> + tmp421@4f {
> + compatible = "ti,tmp421";
> + reg = <0x4f>;
> + };
> +};
> +
> +&i2c10 {
> + status = "okay";
> +
> + tmp421@4f {
> + compatible = "ti,tmp421";
> + reg = <0x4f>;
> + };
> +
> + hdc1080@40 {
> + compatible = "ti,hdc1080";
> + reg = <0x40>;
> + };
> +
> + front_leds: pca9552@67 {
> + compatible = "nxp,pca9552";
> + reg = <0x67>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "led-fault-identify","power-p5v-stby-good",
> + "power-p1v0-dvdd-good","power-p1v0-avdd-good",
> + "","","","",
> + "","","","",
> + "","","","";
> + };
> +};
> +
> +&i2c12 {
> + status = "okay";
> +
> + adm1278@11 {
> + compatible = "adi,adm1278";
> + reg = <0x11>;
> + };
> +
> + tmp421@4c {
> + compatible = "ti,tmp421";
> + reg = <0x4c>;
> + };
> +
> + tmp421@4d {
> + compatible = "ti,tmp421";
> + reg = <0x4d>;
> + };
> +
> + fan_ioexp: pca9552@67 {
> + compatible = "nxp,pca9552";
> + reg = <0x67>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + gpio-line-names =
> + "presence-fan0","presence-fan1",
> + "presence-fan2","presence-fan3",
> + "power-fan0-good","power-fan1-good",
> + "power-fan2-good","power-fan3-good",
> + "","","","",
> + "","","","";
> + };
> +};
> +
> +&i2c13 {
> + multi-master;
> + aspeed,hw-timeout-ms = <1000>;
> + status = "okay";
> +};
> +
> +&gpio0 {
> + gpio-line-names =
> + /*A0-A7*/ "","","","","","","","",
> + /*B0-B7*/ "","","SEL_SPI2_MUX","SPI2_MUX1",
> + "SPI2_MUX2","SPI2_MUX3","","",
> + /*C0-C7*/ "","","","","","","","",
> + /*D0-D7*/ "","","","","","","","",
> + /*E0-E7*/ "","","","","","","","",
> + /*F0-F7*/ "","","","","","","","",
> + /*G0-G7*/ "","SWITCH_FRU_MUX","","","","","","",
> + /*H0-H7*/ "presence-riser1","presence-riser2",
> + "presence-sled0","presence-sled1",
> + "presence-sled2","presence-sled3",
> + "presence-sled4","presence-sled5",
> + /*I0-I7*/ "REV_ID0","","REV_ID1","REV_ID2",
> + "","","","",
> + /*J0-J7*/ "","","","","","","","",
> + /*K0-K7*/ "","","","","","","","",
> + /*L0-L7*/ "","","","","","","","",
> + /*M0-M7*/ "ALERT_SLED0","ALERT_SLED1",
> + "ALERT_SLED2","ALERT_SLED3",
> + "ALERT_SLED4","ALERT_SLED5",
> + "P12V_AUX_ALERT1","",
> + /*N0-N7*/ "","","","","","","","",
> + /*O0-O7*/ "","","","",
> + "","BOARD_ID0","BOARD_ID1","BOARD_ID2",
> + /*P0-P7*/ "","","","","","","","",
> + /*Q0-Q7*/ "","","","","","","","",
> + /*R0-R7*/ "","","","","","","","",
> + /*S0-S7*/ "","","","BAT_DETECT",
> + "BMC_BT_WP0","BMC_BT_WP1","","",
> + /*T0-T7*/ "","","","","","","","",
> + /*U0-U7*/ "","","","","","","","",
> + /*V0-V7*/ "","RST_BMC_MVL","","",
> + "USB2_SEL0_A","USB2_SEL1_A",
> + "USB2_SEL0_B","USB2_SEL1_B",
> + /*W0-W7*/ "RST_FRONT_IOEXP","","","","","","","",
> + /*X0-X7*/ "","","","","","","","",
> + /*Y0-Y7*/ "","","BSM_FLASH_LATCH","","","","","",
> + /*Z0-Z7*/ "","","","","","","","";
> +};
> +
> +&adc0 {
> + vref = <1800>;
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
> + &pinctrl_adc2_default &pinctrl_adc3_default
> + &pinctrl_adc4_default &pinctrl_adc5_default
> + &pinctrl_adc6_default &pinctrl_adc7_default>;
> +};
> +
> +&adc1 {
> + vref = <2500>;
> + status = "okay";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
> + &pinctrl_adc10_default &pinctrl_adc11_default
> + &pinctrl_adc12_default &pinctrl_adc13_default
> + &pinctrl_adc14_default &pinctrl_adc15_default>;
> +};
> --
> 2.25.1
>
On Tue, Dec 21, 2021 at 04:37:55AM +0000, Joel Stanley wrote:
> Hi Patrick,
>
> On Tue, 7 Dec 2021 at 09:52, Howard Chiu <[email protected]> wrote:
> >
> > Initial introduction of Facebook Bletchley equipped with
> > Aspeed 2600 BMC SoC.
> >
> > Signed-off-by: Howard Chiu <[email protected]>
>
> Are you ok for this one to go in for v5.17?
Yes.
Reviewed-by: Patrick Williams <[email protected]>
Would also appreciate if you could apply to your Aspeed tree for OpenBMC.
--
Patrick Williams
On Tue, 21 Dec 2021 at 15:43, Patrick Williams <[email protected]> wrote:
>
> On Tue, Dec 21, 2021 at 04:37:55AM +0000, Joel Stanley wrote:
> > Hi Patrick,
> >
> > On Tue, 7 Dec 2021 at 09:52, Howard Chiu <[email protected]> wrote:
> > >
> > > Initial introduction of Facebook Bletchley equipped with
> > > Aspeed 2600 BMC SoC.
> > >
> > > Signed-off-by: Howard Chiu <[email protected]>
> >
> > Are you ok for this one to go in for v5.17?
>
> Yes.
>
> Reviewed-by: Patrick Williams <[email protected]>
>
> Would also appreciate if you could apply to your Aspeed tree for OpenBMC.
Thanks. I've done both.
On Tue, Dec 07, 2021 at 05:49:24PM +0800, Howard Chiu wrote:
> Initial introduction of Facebook Bletchley equipped with
> Aspeed 2600 BMC SoC.
[...]
> + tpmdev@0 {
> + compatible = "tcg,tpm_tis-spi";
What's the chip used on this board? Going forward, the DT schema for TPMs
requires the exact chip name in addition to the generic "tcg,tpm_tis-spi".
> + spi-max-frequency = <33000000>;
> + reg = <0>;
> + };
> + };
---
Patrick Williams
> On Dec 20, 2023, at 2:07 AM, Lukas Wunner <[email protected]> wrote:
>
> On Tue, Dec 07, 2021 at 05:49:24PM +0800, Howard Chiu wrote:
>> Initial introduction of Facebook Bletchley equipped with
>> Aspeed 2600 BMC SoC.
> [...]
>> + tpmdev@0 {
>> + compatible = "tcg,tpm_tis-spi";
>
> What's the chip used on this board? Going forward, the DT schema for TPMs
> requires the exact chip name in addition to the generic "tcg,tpm_tis-spi".
Why is this a requirement? This assumes there is exactly one chip. TPMs are often placed on a pluggable module in which multiple vendors could be used. There is no way in the DTS to specify multiple compatible chips.
>> + spi-max-frequency = <33000000>;
>> + reg = <0>;
>> + };
>> + };
On Wed, Dec 20, 2023 at 06:38:59AM -0600, Patrick Williams wrote:
> On Dec 20, 2023, at 2:07AM, Lukas Wunner <[email protected]> wrote:
> > On Tue, Dec 07, 2021 at 05:49:24PM +0800, Howard Chiu wrote:
> > > Initial introduction of Facebook Bletchley equipped with
> > > Aspeed 2600 BMC SoC.
> > [...]
> > > + tpmdev@0 {
> > > + compatible = "tcg,tpm_tis-spi";
> >
> > What's the chip used on this board? Going forward, the DT schema for TPMs
> > requires the exact chip name in addition to the generic "tcg,tpm_tis-spi".
>
> Why is this a requirement? This assumes there is exactly one chip.
> TPMs are often placed on a pluggable module in which multiple vendors
> could be used. There is no way in the DTS to specify multiple compatible
> chips.
It seems to be a convention to provide the name of the chip that's
actually used, in addition to the generic compatible.
One advantage I see is that specific properties can be enforced per-chip.
E.g. Infineon SLB9670 TPMs support an SPI clock of up to 43 MHz,
whereas Atmel ATTPM20P support 36 MHz. The devicetree schema may
contain those maximum speeds and the validator can check whether
devicetrees observe them.
Similarly, a device driver may use chip-specific quirks based on the
compatible string.
Last not least, it is useful for documentation purposes to specify which
chip is used.
If chips are dual-sourced or triple-sourced, as you say, and they
behave identically, then I think it is fine to specify all of their
compatible strings plus the generic compatible. If they do not
behave identically, separate devicetrees should be used for each
board version with a different chip.
As for specifying the generic compatible last, this follows from
section 2.3.1 of the devicetree specification:
"The compatible property value consists of one or more strings
that define the specific programming model for the device.
This list of strings should be used by a client program for
device driver selection. The property value consists of a
concatenated list of null terminated strings, from most specific
to most general."
https://buildmedia.readthedocs.org/media/pdf/devicetree-specification/latest/devicetree-specification.pdf
Thanks,
Lukas
(cc'd TPM mailing list for awareness)
On Wed, Dec 20, 2023 at 06:00:12PM +0100, Lukas Wunner wrote:
> On Wed, Dec 20, 2023 at 06:38:59AM -0600, Patrick Williams wrote:
> > On Dec 20, 2023, at 2:07AM, Lukas Wunner <[email protected]> wrote:
> > > On Tue, Dec 07, 2021 at 05:49:24PM +0800, Howard Chiu wrote:
> > > > Initial introduction of Facebook Bletchley equipped with
> > > > Aspeed 2600 BMC SoC.
> > > [...]
> > > > + tpmdev@0 {
> > > > + compatible = "tcg,tpm_tis-spi";
> > >
> > > What's the chip used on this board? Going forward, the DT schema for TPMs
> > > requires the exact chip name in addition to the generic "tcg,tpm_tis-spi".
> >
> > Why is this a requirement? This assumes there is exactly one chip.
> > TPMs are often placed on a pluggable module in which multiple vendors
> > could be used. There is no way in the DTS to specify multiple compatible
> > chips.
>
> It seems to be a convention to provide the name of the chip that's
> actually used, in addition to the generic compatible.
My impression is that this is subsystem dependent. The MTD SPI-NOR
subsystem, for example, does not want any compatible or additional devices
added and instead `compatible = "jedic,spi-nor"` is all you need. The
subsystem does the SFDP detection of the specific device (and
parameters) [1].
> One advantage I see is that specific properties can be enforced per-chip.
> E.g. Infineon SLB9670 TPMs support an SPI clock of up to 43 MHz,
> whereas Atmel ATTPM20P support 36 MHz. The devicetree schema may
> contain those maximum speeds and the validator can check whether
> devicetrees observe them.
Noble goal.
For the Aspeed SOC that we use to interact with the TPM module, the
hardware logic doesn't properly implement bi-directional access, so we
end up using the SPI-GPIO driver and running at speeds far far below any
device maximum (obviously this isn't everyone's problem).
> Similarly, a device driver may use chip-specific quirks based on the
> compatible string.
IMO, if a chip requires quirks in order to function properly then it
isn't compatible with "tcg,tpm_tis-spi" is it? Standards exist for a
reason. If a chip can't follow them, don't claim it does.
> Last not least, it is useful for documentation purposes to specify which
> chip is used.
>
> If chips are dual-sourced or triple-sourced, as you say, and they
> behave identically, then I think it is fine to specify all of their
> compatible strings plus the generic compatible.
This has explicitly been rejected before; having multiple incompatible
chips listed in the same compatible. I've tried to search lore but I
can't find a reference unfortunately. We've had similar scenarios with
second-source scenarios and have been told to: change the DTS in u-boot,
use user-space bind calls, or work with the DTS overlay project to get
that working. Frankly, all of those options are a challenge for
something fundamental like the TPM.
Furthermore, what you're suggesting does not jive with what is in the
devicetree binding documentation for tpm_tis-spi [2]:
- compatible: should be **one** of the following (emphasis mine)
> If they do not
> behave identically, separate devicetrees should be used for each
> board version with a different chip.
I am not following how that would work in a reasonable way. As I said,
these are pluggable modules and not simply second-source builds. There
are a collection of modules that can all be plugged into the same header.
They might not even be shipped with the device... You might want TPM
modules provisioned under control of your own process, rather than the
device manufacturer, and you plug them in prior to using the device.
The only way I can conceive of doing this is to have a good chunk of u-boot
code that detects which module is plugged in and manually modifies the
compatible string in the DTS before loading the kernel. Of course,
doing this changes your measurements and has to be done in the CRTM,
both of which decrease your security posture.
1. https://lore.kernel.org/lkml/[email protected]/
2. https://github.com/torvalds/linux/blob/c0f65a7c112b3cfa691cead54bcf24d6cc2182b5/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt#L2
--
Patrick Williams
On Fri, Dec 22, 2023 at 04:38:12PM -0600, Patrick Williams wrote:
> On Wed, Dec 20, 2023 at 06:00:12PM +0100, Lukas Wunner wrote:
> > If chips are dual-sourced or triple-sourced, as you say, and they
> > behave identically, then I think it is fine to specify all of their
> > compatible strings plus the generic compatible.
>
> This has explicitly been rejected before; having multiple incompatible
> chips listed in the same compatible. I've tried to search lore but I
> can't find a reference unfortunately.
I'll let devicetree maintainers comment on that.
> Furthermore, what you're suggesting does not jive with what is in the
> devicetree binding documentation for tpm_tis-spi [2]:
>
> - compatible: should be **one** of the following (emphasis mine)
That's superseded by:
https://lore.kernel.org/all/[email protected]/
I don't really have a dog in this fight, I merely stepped up to
convert TPM DT bindings to YAML. There have been multiple attempts
to convert them in the past but none of them have been pursued into
mainline.
I looked at compatible string usage in arch/arm{,64}/boot/dts
and was under the impression that the majority of devicetrees
use a combo matching this pattern:
"vendor,chip", "tcg,tpm[_-]tis-{spi,i2c,mmio}"
So that's what I went for in the conversion. It would be inconsistent
to enforce a generic compatible for i2c and mmio, but not for spi.
I ran the validator against all arm/arm64 devicetrees and there are
four devicetrees which only use a generic compatible and not a
"vendor,chip" compatible:
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi
arch/arm/boot/dts/aspeed-bmc-facebook-wedge400.dts
arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
So, three Aspeed Facebook and one Moxa. There's a fifth case (phyTEC)
but the devicetree author clarified it's an Infineon SLB9670.
The authors of the other four devicetrees listed above did not respond.
Patches to fix up schema violations are here:
https://github.com/l1k/linux/commit/7813a455ed15393df7d9d353173635b98ae23387
https://github.com/l1k/linux/commit/a958be44952b1de170100be1007780a72ce7d861
> As I said,
> these are pluggable modules and not simply second-source builds. There
> are a collection of modules that can all be plugged into the same header.
> They might not even be shipped with the device...
If those TPM modules might not even be plugged in or are interchangeable,
I think they ought to be represented as DT overlays.
Honestly I'm wondering how common the scenario you're describing is.
If it's an edge case, it might not be worth holding up the YAML
conversion because of it. The missing YAML conversion is a constant
cause of pain for a lot of people.
Thanks,
Lukas
On Sat, Dec 23, 2023 at 09:36:23AM +0100, Lukas Wunner wrote:
> On Fri, Dec 22, 2023 at 04:38:12PM -0600, Patrick Williams wrote:
> > On Wed, Dec 20, 2023 at 06:00:12PM +0100, Lukas Wunner wrote:
> > > If chips are dual-sourced or triple-sourced, as you say, and they
> > > behave identically, then I think it is fine to specify all of their
> > > compatible strings plus the generic compatible.
> >
> > This has explicitly been rejected before; having multiple incompatible
> > chips listed in the same compatible. I've tried to search lore but I
> > can't find a reference unfortunately.
>
> I'll let devicetree maintainers comment on that.
>
>
> > Furthermore, what you're suggesting does not jive with what is in the
> > devicetree binding documentation for tpm_tis-spi [2]:
> >
> > - compatible: should be **one** of the following (emphasis mine)
>
> That's superseded by:
>
> https://lore.kernel.org/all/[email protected]/
>
> I don't really have a dog in this fight, I merely stepped up to
> convert TPM DT bindings to YAML. There have been multiple attempts
> to convert them in the past but none of them have been pursued into
> mainline.
Thank you for the effort and context. I wasn't aware of this pending
change.
> I looked at compatible string usage in arch/arm{,64}/boot/dts
> and was under the impression that the majority of devicetrees
> use a combo matching this pattern:
> "vendor,chip", "tcg,tpm[_-]tis-{spi,i2c,mmio}"
>
> So that's what I went for in the conversion. It would be inconsistent
> to enforce a generic compatible for i2c and mmio, but not for spi.
>
> I ran the validator against all arm/arm64 devicetrees and there are
> four devicetrees which only use a generic compatible and not a
> "vendor,chip" compatible:
> arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
> arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi
> arch/arm/boot/dts/aspeed-bmc-facebook-wedge400.dts
> arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
After some investigation, it should be safe to use "infineon,slb9670"
for all of the facebook systems. If you want to add that to your patch
set you can cc me and Tao Ren ([email protected]) and I will at
least give my Reviewed-by.
> So, three Aspeed Facebook and one Moxa. There's a fifth case (phyTEC)
> but the devicetree author clarified it's an Infineon SLB9670.
> The authors of the other four devicetrees listed above did not respond.
>
> Patches to fix up schema violations are here:
> https://github.com/l1k/linux/commit/7813a455ed15393df7d9d353173635b98ae23387
> https://github.com/l1k/linux/commit/a958be44952b1de170100be1007780a72ce7d861
>
>
> > As I said,
> > these are pluggable modules and not simply second-source builds. There
> > are a collection of modules that can all be plugged into the same header.
> > They might not even be shipped with the device...
>
> If those TPM modules might not even be plugged in or are interchangeable,
> I think they ought to be represented as DT overlays.
I still don't think DT overlays are appropriate for TPMs as it
effectively extends the attack surface for the kernel PCRs all the way
until you can run enough code to load the appropriate DT overlay,
which is likely somewhere in userspace. This seriously diminishes the
value of measured boot.
> Honestly I'm wondering how common the scenario you're describing is.
> If it's an edge case, it might not be worth holding up the YAML
> conversion because of it. The missing YAML conversion is a constant
> cause of pain for a lot of people.
Understood.
Since any of the chips we might be using are currently equivalent from a
driver perspective with the generic TCG spec (and the infineon,slb9670
compatible) we should be fine. If there becomes an incompatibility in
the future with the tpm_tis_spi code we'll cross that bridge at that
time.
--
Patrick Williams